Professional Documents
Culture Documents
Digisol STB User Guide
Digisol STB User Guide
ADSL2/2+ Ethernet
Broadband Router
DG-BG1000
ADSL
2/2+
24 Mbps
V1.0
2011-12-13
Trademarks:
DIGISOLTM is a trademark of Smartlink Network Systems Ltd. All other
trademarks are the property of the respective manufacturers.
Package Contents
The following items should be present in your package:
DG-BG1000 ADSL2/2+ Router
Switching power adapter
POTS splitter
Two RJ-11 cables
One RJ-45 patch cord
Quick Installation Guide
Installation Guide CD
Make sure that the package contains above items. If any of the listed
items is damaged or missing, please contact your retailer immediately.
Product Overview
Thank you for purchasing DG-BG1000 ADSL2/2+ Ethernet Broadand
Router! The DG-BG1000 is an ADSL router that supports multiple line
modes. It provides one 10/100Base-T Ethernet interface at the user
end. The device provides high-speed ADSL broadband connection to the
Internet or Intranet users, such as cyber caf and office. The device
provides high performance access to the Internet with downlink speed
of up to 24 Mbps and uplink up to 1 Mbps.
Product Features
Download speed up to 24Mbps and upload speed up to 1Mbps
Multiple PVCs support (up to eight)
DHCP server & client
NAT & NAPT
Static routing
Virtual server & DMZ
IP filter
Quality of Service (QoS)
Universal plug and play (UPnP)
System Requirements
The following system requirements are recommended
Pentium 233MHz or above
Memory 64MB or above
Ethernet network interface card with Win 2000/XP/Vista/Win7
Web Browser (IE6 or above)
Front View
Below shown is the front view of the product.
Rear View
Below shown is the rear view of the product.
Power ON/OFF
Switch
Power Connector
LAN Port
ADSL Line
Port
Factory
Reset
Interface Description
Following is the description for the interfaces on the router.
Interface
Power switch
Power Connector
Ethernet
Reset
Line
Description
Power ON or Power OFF the device.
Power interface, for connecting to the power adapter.
RJ-45 interface, for connecting to the Ethernet interface of PC or
other Ethernet devices through the Ethernet cable.
Reset to the factory defaults. To reset to the factory defaults, keep
the device powered ON and push a paper clip in to the hole for over
5 seconds. Then release it, the configuration is reset to the factory
defaults.
RJ-11 interface, for connecting to the ADSL interface or a splitter
through the telephone cable.
LED Description
The LED description for the router is as given below:
LED Name LED Color
Green
Power
Red
Link
Green
Status
Green
Data
On
Blinks
Off
Red
On
Green
Blinks
On
Ethernet
Description
On
Off
The device is handshaking with the physical layer of the office end.
The device has a successful WAN connection (PPP dial-up is
successful) in the routing mode and no data is being transmitted on
the Internet.
Data is being transmitted on the Internet in the routing mode.
The device is in the bridged mode.
In the routing mode, after the successful synchronization, the WAN
connection has failed (PPP dial-up is failed).
The LAN connection is normal and activated.
Data is being transmitted on the LAN or data is being transmitted on
the Internet in the bridged mode.
The LAN connection of the device has failed.
Router Installation
1 Insert the Setup CD into your CD-ROM drive of notebook/desktop
computer.
6 The following screen displays the LED status of the router. Click
7 In this page, enter the user ID and password to log in to the router.
8 Configure the ADSL setting for the router in the following screen.
Select the country and service provider from the drop-down list. You
can change the default VPI/VCI values as instructed by your ISP.
?
VPI: The valid value is in the range of 0 to 255.
?
VCI: The valid value is in the range of 32 to 65535.
Click Next to continue with the installation.
11