Professional Documents
Culture Documents
XCAL DRT LTE Scanner Quick Guide
XCAL DRT LTE Scanner Quick Guide
Description
Power On/Off
Unit is powered on by connecting the power cable and power off by disconnecting
power cable
Control Interface
The unit maybe connected directly to a PC through and Ethernet crossover cable.
When directly connected to a PC the unit must be setup using a static IP address a
nd the PC must also be configured with a static IP address
address.
Port Setting
1. Check Scanner button
2. Click Alias Setting button
3. Type Interface name and select Scanner Type
* Available scanner List will be shown in List box when y
you click Find Scanner button
New Task
1. If Scanner H/W is successfully synchronized with XCAL-LTE then you can
see New Task button become to Enable status
* Scanner 1 section on the left bottom side of XCAL main window would changed
g its color to Blue.
RF Setting
Scanner parameters
MeasurementEnable:
RS:RSRP(dBm),RSRQ(dB) WhenthisboxischeckedtheReferenceSignalReceivedPowerandReferenceSignalRec
eivedQualitywillbeincludedinthemeasurement
DetectionMode
D
i M d
ASYNC Detectionisattemptedwithoutattemptingtosynchronizingtothedownlinksignal
SYNC DetectionisperformedfollowingthesynchronizationofthedownlinksignaltoaknownstandardsuchasGPS
Robust Whenworkinginanenvironmentwithincreasednoiseandinterference,Robustmodewillimprove
detectionbyperformingamoredetailedanalysisofthesignal.RobustmodeisslowerthanASYNCortheSYNC
yp
g
y
g
Modes.
NumberofTXAntennas Specifiesthenumberoftransmitantennasbeingusedbythebasestation
ObservationtoAverage Thenumberofobservationsthatmustbedetectedbeforereportingthechannel.
PSCHDetectThreshold ThesignallevelbelowwhichthePrimarySynchronizationChannel(PSCH)decodeddataisnotretu
rned.ThisthresholdisenabledwhenMeasurementEnable,SCHisselected,otherwiseithasnoeffect.Thedefaultvalue
forthissettingis 10dB
SSCHDetectThreshold ThesignallevelbelowwhichtheSecondarySynchronizationChannel(SSCH)decodedataisnotret
urned.ThisthresholdisenabledwhenMeasurementEnable,SCHisselected,otherwiseithasnoeffect.Thedefaultvalue
is6dB
RSDetectThreshold
RS
Detect Threshold ThesignallevelbelowwhichtheRSdecodeddataisnotreturned.ThisthresholdisenabledwhenM
The signal level below which the RS decoded data is not returned This threshold is enabled when M
easurementEnable,RSisselected,otherwiseithasnoeffect.Thedefaultvalueforthissettingis20dB.
7
PCI Setup
PCI Setup
FilteringMode Selectsthetypeoffilteringtobeusedfordecoding.TopN returnsuptoNsetsofdata
whereNisthenumberenteredintheTopN Valuefield.
TopN Value Themaximumnumberofdatasetsthatwillbereturned.Thelargestentryis127.
PCI AllowsyoutoselectthePhysicalLayerCellIdentity(PCI)
PCIGroup AllowsyoutoselectthePCIGroup.
Count Thenumberofpairsintheunlabeledsearchfield
Unlabeledfield ThisfieldcontainsthePCI/PCIGrouppairsthatwillbesearchedforduringthesurvey.Only
dataonthesepairswillbereturned.Thisfieldcanhaveamaximumof127pairs.
Save/Load Setting
1.
2.
3.
10
Start Scan
1. Click Play Icon to start measurement
* To stop measurement and terminate task, click Stop Icon and Exit button
* You can select Key parameters what you want to see in the red marked list box
2. Click Bar graph to check detail measurement result for corresponded PCI
11
Thank You
12