Professional Documents
Culture Documents
Paper 2 2012
Paper 2 2012
IIAT-CHENNAI
1.
fires in flammable petroleum products or other flammable or combustible
liquids, greases, solvents, paints, etc is classified as
a.
class A fire
b.
class B fire
c.
class C fire
2.
a.
b.
c.
d.
3.
If distance of cg from datum is 160 and of leading edge of MAC is 140 and
length of MAC is 100. Find MAC %
a.
20%
b.
50%
c.
75%
4.
If the input of half wave rectifier is 240 V and transformer has a step down ratio
of 8:1, what is the output rms value?
a.
42.2 V
b.
30V
5.
a.
b.
c.
Demultiplexer is
Output is same as multiplexer
Output is opposite of multiplexer
As in b CCU regulates in input and output
6.
a.
b.
7.
a.
b.
c.
8.
A metal which can be hammered, rolled, or pressed into various shapes
without cracking, breaking, or leaving some other detrimental effect, is said to be
a.
Malleable
b.
Ductility
9.
MTCS regarding Austenite is
a.
The name given to steel when it is heated above the critical range, consists of
a solid solution of cementite in gamma iron.
10.
a.
b.
c.
d.
11.
a.
b.
c.
d.
12.
a.
b.
c.
d.
MTCS
turboprop engine requires lengthy runway than piston engine of same power
turbojet has more weight than piston engine of same power
turbofan required short runway as compare to turbojet
all of the above
13.
a.
b.
c.
14.
a.
b.
c.
15.
a.
b.
c.
d.
16.
a.
b.
c.
18.
We can get vastly superior product than iron If carbon is added to iron, in
percentages ranging up to
a.
Approximately 0.5 percent.
b.
Approximately 1 percent.
c.
If Nickel 3.50%, chromium 1.55% is present
19.
a.
b.
c.
20.
a.
b.
c.
d.
21.
a.
b.
c.
d.
22.
a.
b.
c.
Stringers, bulkhead, skin, rivet and extruded section are made from
Cast aluminum alloy
Wrought aluminum alloy
Pure aluminum
23.
a.
b.
c.
d.
24. Slots provided on the armature are not parallel but are staggered at an angle to
provide
a.
Safety
b.
Reduce the humming noise
c.
Stability.
d.
..
25.
a.
b.
c.
d.
26.
a.
b.
c.
27.
a.
b.
c.
d.
..
Damaged rivets can be removed by
Drive punch
Prick punch
Hollow punch
Both a and b
28.
a.
b.
c.
d.
29. If the peak value is 100 volts then at an angle of 30 what is the instantaneous
value
a.
50 V
b.
100 V
c.
150 V
d.
200 V
30
a) Carbon steel
31
The type of torque wrench which has the ability to preset the torque
a)
b)
c)
no nozzle obstruction
d)
33
a)
induced drag
b)
parasite drag
c)
profile drag
34
a)
it
lift equals drag and drag is the resistance of the air to objects moving through
b)
thrust equals weight and thrust is derived from jet propulsion or from a
propeller and engine combination
c)
d)
35
36 devices which make it possible to obtain more than one voltage from a
single power source
a)
Current divider
b)
Potential divider
c)
Resistance divider
d)
Inductance
b)
Capacitance
c)
Resistance
d)
38
1. Pay load
2. Zero fuel weight
39 medium threads is
a) Class 1
b) class 2 c) class 3
b) rope c) chain
b) eye bolt
a)
b)weft
44 Cable MTCS
a) Frequent adjustment of the cable tension
b) Low mechanical efficiency
c) High strong and high weight
d) all
45 what is an alternator
Ac current generator
a)
CRT COLOUR
1.
2.
48
1.
EICAS
Engine indicating and crew alerting system
49
RMS value in half wave is 10 amp, what will be the rms value if it is
full wave rectified
1. 14.14 amp
2. 20/ amp
3. 40/ amp
50
a)
Heat treated Al. alloy internally and the surface material is
commercially pure Al.
b)
Commercially pure Al. and the surface material is head treated Al. alloy
Stain hardened Al. alloy and the surface is pure Al
56
1. .00001
2. .001
3. .0001
57
Which too is generally used to calibrate a m.m or check its
accuracy
1. Gauge block
2. DTI
3. Machinist scale
58
59
2.Junction network
3. Open ckt
1. When two surfaces fit tightly together but can move relative to one
another
2. When two distance metals are in contact
3. When two surfaces fit loosely together but can move relative to one another
60
1. Reduce oxidation
2. Remove the oxides
d)
4. All
63
1. Size
2. Shape
3. Vapour and fluid compatibility
Q64. Which cable has high resistance to fatigue?
1. Galvanized
2. Stainless steel
3. Carbon steel
65 Which brazing method is used for precious by localized parts
1. Induction
2. Torch brazing
3) Resistance brazing
4. Furnace brazing
66 When all others parameters are remains unchanged
1. Less the aspect ratio, more the induce drag
2. More the aspect ratio less the induce drag
3. Higher the angle of attack, higher the induce drag
4. Higher the angle of attack, less the induce drag
67
In orthographic projection
common
1. Reduce reactance
2. Reduce copper loss
70
1. Stratosphere
2. Tropopause
3. Troposphere
4. Ionosphere
71
a)
72
a) Direct register
73 8085 microprocessor
VL =VP c) IL=IP
D).