Professional Documents
Culture Documents
Dunlop Conveyor Handbook
Dunlop Conveyor Handbook
DUNLOP Belting
Print
INDEX
Introduction
Dunlop Conveyor Belting Range
Belting Characteristics
Additional Features
SABS Specifications
Conveyor Belt Design
Step By Step Example of Belt Tension Calculation
Table 1: Table of Symbols
Table 2: Material Characteristics
Table 2(a): Typical Flowability
Determination of Conveyor Capacities
Table 3: Capacities of Troughed Belt Conveyors
Table 4: Recommended Maximum Belt Speed for Normal Use
Table 5: Recommended Idler Spacing
Table 6: Friction Factors
Table 7: Sag Factor
Table 7(a): Recommended Percentage Sag
Table 8: Estimated Belt Mass
Table 9: Typical Mass of Rotating Parts of Idlers
Table 10: Mass of Moving Parts
Table 11: Drive Factor
Conveyor Belt Selection
Table 12: Maximum Recommended Operating Tensions
Table 13: Recommended Minimum Pulley Diameters
Table 14: Load Support
Table 15: Maximum Number of Plies Recommended for Correct Empty Belt Troughing
Table 16: Carcass Thickness
Table 17: Mass of Belt Carcass
Table 18: Mass of Covers per mm of Thickness
Rate of Wear Graph
Table 19: Minimum Belt Top Cover Gauge Guide
Table 20: Belt Modulus
Tabulator Calculations
Sheet 1: Empty Belt
Sheet 2: Fully Loaded Belt
Sheet 3: Non-Declines Loaded
Sheet 4: Declines Loaded
Tension Tabulator
Vertical Curves
Maximum Incline Angle
Graph for Estimating Belt Length/Rolled Belt Diameter
Useful Data Conversion Factors
Conveyor Belting Design Manual
INTRODUCTION
Dunlop Africa Industrial Products is the leading designer and manufacturer of industrial rubber products in South Africa. In fact our belting
systems can be seen on some highly productive plants all around the globe.
What more can you expect, when you consider that our belts have been designed and fabricated by some of the best engineers in the
industry and from only the finest raw materials.
Using the most current technology, many components have taken years of refinement to attain such technological precision. And every belt
is guaranteed to provide maximum performance and maximum life.
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/Dunlop/Belting%20B... 24/05/2004
Dunlop Conveyor Belt Design Manual Page 2 of 33
And with some 750 000 various specifications available, you can expect to find the right belt for your requirements no matter how
specialised.
This manual contains all the elements, formulae and tables you need to specify the exact belt. It has been compiled for your benefit, as a
quick reference book for easy selection. If however you have an application not covered in the following pages, please contact Dunlop Africa
Industrial Products. A team of experienced and helpful engineers will be pleased to assist you.
Our range of excellent products, competitive pricing and impeccable service, has earned Dunlop Africa Industrial Products the reputation of
being the market's first choice.
Dunlop Africa Industrial Products manufactures the most comprehensive range of conveyor belting in South Africa.
z Rufftop belting
z Endless belts
z Woodmaster
Steelcord belting
Flinger belts
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/Dunlop/Belting%20B... 24/05/2004
Dunlop Conveyor Belt Design Manual Page 3 of 33
BELTING CHARACTERISTICS
z From the early days of cotton duck plies, progress has been made in the manufacture of all-synthetic plies offering many
advantages.
z The range of strengths has been greatly increased, with improvements in the flexible structure. The modern multi-ply belt is
manufactured with a synthetic fibre carcass in a wide slab, then slit to width as required for individual orders.
z A wide range of belt specifications is available with current belt constructions having versatile applications.
z The standard XT belting (Grade N) incorporates covers suitable for the handling of most abrasive materials, having a blend of
natural and synthetic rubber.
z Grade M Belts have covers with high natural rubber content recommended for belts operating under extremely arduous conditions
where cutting and gouging of covers occurs.
z Phoenix Heat Resistant belting covers are styrene butadiene based and are recommended for belts handling materials with
temperatures up to 1200C.
z Super Phoenix Heat Resistant belts have chlorobutyl covers and are recommended for belts handling materials with temperatures
of up to 1700C.
z Delta Hete heat resistant belting with EPDM synthetic rubber covers in a formulation developed to allow conveying materials of
temperatures up to 2000C.
z Fire Resistant XT belting is manufactured with covers containing neoprene and multi-ply carcass constructions to meet the
stringent standards for safety in all underground mining industries and is therefore particularly suited to shaft applications.
Woodmaster
z This belt has been especially developed for the Timber Industry. The rubber has been compounded to provide resistance to oil and
resin, and is non-staining.
Rufftop Belting
z This is a range of rough top package belting, of two or three ply all-synthetic carcass belts with deep impression rubber covers.
The range is ideal for the packaging and warehousing industries and baggage handling installations such as airports and railway
stations etc.
z Riffled conveyor belting has raised edges, is 1 500 mm wide and available in endless form. These belts are uniquely applied at
gold mine concentrators.
z Food quality belting is ideal where foodstuffs come into direct contact with the belt surface. This range of belting is manufactured
from non-toxic materials and is resistant to oils, fats and staining, and meets the strict hygiene requirements laid down by the
food processing industry. The two types available are Grey food belting and Salmon pink belting
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/Dunlop/Belting%20B... 24/05/2004
Dunlop Conveyor Belt Design Manual Page 4 of 33
Endless Belting
z The complete XT range can be made available as factory spliced endless belts. These belts are recommended for short conveyor
installations. (Suitable for lengths up to 50 in.)
Flinger Belts
z Flinger Belts are fitted to flinger conveyors, the primary function of which is to disperse the discharging material over a wide area,
thus minimising heap build-up below the main conveyor. The flinging effect is achieved by running the flinger belt at a high speed
in a U configuration. Flinger belts are built and cured on a drum to eliminate a spliced join.
z Commonly known as 'Vinyplast' solid woven PVC. The construction has inherently high fastener holding qualities. The belting is
constructed of polyester and nylon with a cotton armouring, is impregnated with PVC and has PVC covers. These belts have been
specially developed to resist impact, tear, rot and abrasion and to meet the most stringent flame-resistant standards.
z The nitrile cover on solid woven PVC belts is specially designed to meet the SABS specifications for use in mines, where a fire
hazard exists. In general the nitrile cover has good flame-retardant properties and oil, abrasion and heat resistance.
z Steelcord conveyor belting is designed for very long hauls where textile reinforcement would either not achieve the requisite
strength or would have too high an elongation at reference load. Resistance to severe shock and exceptional tensile loading is
achieved by the wire reinforcement encased between thick top and bottom covers of the highest quality rubber. These belts are
designed to conform to or exceed the requirements of stringent standards and offer a long belt life.
Fire Resistant Steelcord Belting (Conforms to SABS 1366. 1982 type F).
z Steelcord belting of fire-resistant quality is made with specially compounded rubbers which render it self extinguishing. Fire-
resistant steelcord belting offers great advantages in maintenance-free operation and long belt life for conveyors situated in fiery
mines.
z Oil resistant belting provides easily cleanable covers of either nitrile or neoprene on all-synthetic fabric plies. Choice of covers
gives maximum resistance to mineral and vegetable oils thus permitting the user to convey a wide variety of materials containing
mineral and vegetable oils.
ADDITIONAL FEATURES
1. Rip Protector
As an additional feature rip protection can be incorporated into the belt by means of arranging strong nylon fibres transversely or
by inclusion of electronic loops. The textile rip protection can be built into the belt in 2-metre lengths at regular intervals or over
the full length of the belt.
For applications where the lump size of the material carried is large and where adverse loading conditions exist, an open weave
breaker ply can be incorporated below the top cover as an extra protection for the carcass.
This incorporates steel tyre cord in a 'V shape, as a rip protection, at intervals over the belt length. Particularly recommended for
XT belting where arduous conditions are experienced i.e. slag transportation.
4. Belt Edges
Many conveyor belts track off at some stage of their lives, causing edge damage to a greater or lesser extent. Belts can be
supplied with either slit or moulded edges.
Slit edges:
All-synthetic constructed carcasses have good resistance to edge chafing, due to modern fibre construction In addition there is
minimal penetration of moisture to the carcass and therefore no problem with carrying out hot vulcanised splices or repairs.
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/Dunlop/Belting%20B... 24/05/2004
Dunlop Conveyor Belt Design Manual Page 5 of 33
Moulded edges:
A moulded rubber edge can be provided to protect the carcass from acids, chemicals and oils. In most applications a moulded
edge is unnecessary as synthetic fibres will not rot or be degraded by mildew.
SABS SPECIFICATIONS
Dunlop Africa Industrial Products conveyor belting complies with the stringent standards as laid down by the SABS.
The above specifications cover the requirements of the various conveyor belts and are classified according to the minimum full thickness
breaking strength of the finished belting in kilonewtons per metre width.
Introduction
1. Reinforcement or a carcass which provides the tensile strength of the belt, imparts rigidity for load support and provides a means
of joining the belt.
2. An elastometric cover which protects the carcass against damage from the material being conveyed and provides a satisfactory
surface for transmitting the drive power to the carcass.
In selecting the most suitable belt for a particular application, several factors have to be considered:
1. The tensile strength of the belt carcass must be adequate to transmit the power required in conveying the material over the
distance involved.
2. The belt carcass selected must have the characteristics necessary to:
a. provide load support for the duty.
b. conform to the contour of the troughing idlers when empty, and
c. flex satisfactorily around the pulleys used on the conveyor installation.
3. The quality and gauge of cover material must be suitable to withstand the physical and chemical effects of the material conveyed.
Belt Tensions
In order to calculate the maximum belt tension and hence the strength of belt that is required, it is first necessary to calculate the effective
tension. This is the force required to move the conveyor and the load it is conveying at constant speed. Since the calculation of effective
tension is based on a constant speed conveyor, the forces required to move the conveyor and material are only those to overcome frictional
resistance and gravitational force.
For the sake of simplicity the conveyor is considered to be made up of interconnected unit length components all of equal mass. The mass
of each of these units is called the mass of the moving parts and is calculated by adding the total mass of the belting, the rotating mass of
all the carrying and return idlers and the rotating mass of all pulleys. This total is divided by the horizontal length of the conveyor to get the
mean mass of all the components. At the outset the belt idlers and pulleys have not been selected and hence no mass for these components
can be determined. Therefore the mass of the moving parts is selected from the tabulated values to be found in Table 10.
As is the case with the components the load that is conveyed is considered to be evenly distributed along the length of the conveyor. Given
the peak capacity in ton per hour the mass of the load per unit length is given by:
τ τ
Q = 0,278 or Q=
S 3,600S
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/Dunlop/Belting%20B... 24/05/2004
Dunlop Conveyor Belt Design Manual Page 6 of 33
Te = Tx + Ty + Tz +Tu
Tx = 9,8G x fx x Lc
Tz = 9,8Q x H
Various conveyor accessories that add resistance to belt movement are standard on most conveyors. The most common are skirtboards at
the loading point and belt scrapers. Other accessories include movable trippers and belt plows.
9,8fs x Q x Ls
Tus =
S x b²
Tuc = A x ρ x fc
In the case of a belt plow the additional tension required to overcome the resistance of each plow is
Tup = 1,5W
Moving trippers require additional pulleys in the system and therefore add tension. If the mass of the additional pulleys has been included in
the mass of moving parts then no additional tension is added. However, if a separate calculation of the tension to overcome the resistance
of the additional pulleys is required this can be determined for each additional pulley as follows
do x T 1
Tut = 0,01
Dt
Corrected length Lc
Short conveyors require relatively more force to overcome frictional resistance than longer conveyors and therefore an adjustment is made
to the length of the conveyor used in determining the effective tension. The adjusted length is always greater than the actual horizontal
length.
LC = L + 70
Lc
C=
L
All conveyors require an additional tension in the belt to enable the drive pulley to transmit the effective tension into the belt without
slipping. This tension, termed the slack side tension T2, is induced by the take-up system. In the case of a simple horizontal conveyor the
maximum belt tension T1 is the sum of the effective tension Te and the slack side tension T2
ie: T1 = Te + T2
For a more complex conveyor profile that is inclined, additional tensions are induced due to the mass of the belt on the slope. This tension is
termed the slope tension 'h and increases the total tension.
Thus T1 = Te + T2 + Th
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/Dunlop/Belting%20B... 24/05/2004
Dunlop Conveyor Belt Design Manual Page 7 of 33
The slack side tension is determined by consideration of two conditions that must be met in any conveyor. The first condition is that there
must be sufficient tension on the slack side to prevent belt slip on the drive. The second condition is that there must be sufficient tension to
prevent excessive sag between the carrying idlers.
T1
= eµθ
T2
Since T1 = Te + T2
1
T2 = Te
eµθ - 1
1
The expression :
eµθ - 1
is called the drive factor k. and the value of T2 that will just prevent slip is referred to as the minimum to prevent slip Tm and therefore
Tm = k x T e
The tension required to limit sag is dependent on the combined mass of belt and load, the spacing of the carry idlers and the amount of sag
that is permissable.
Ts = 9,8Sf x (B + Q) x ld
The value of the slack side tension must ensure that both conditions are met and therefore T2 must be the larger of Tm or Ts.
Slope tension Th
The slope tension is the product of the belt weight and the vertical lift and has its maximum value at the highest point of the conveyor.
Th = 9,8B x H
Unit tension T
The maximum belt tension T1 has as its reference width the full width of the belt. Usually this is converted to the tension per unit of belt
width as this is the reference dimension for belt strengths.
T1
T=
W
Absorbed power
The amount of power required by the conveyor is by definition of power equal to the product of the force applied and the speed at which the
conveyor belt travels. The force applied is the effective tension and hence the power required at the shaft of the drive pulley/s is
P = Te x S
As an example of the application of the formulae the belt tensions for the following conveyor will be determined:
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/Dunlop/Belting%20B... 24/05/2004
Dunlop Conveyor Belt Design Manual Page 8 of 33
τ
Q= 0,278
S
0,278 x 400
=
1,4
= 79,4 kg/m
2. Look up the value of the mass of moving parts in Table 10. From the idler roll diameter and the nature of the material conveyed
the application is considered as medium duty. For a 900 mm wide belt the mass of moving parts from Table 10 is 55 kg/m
3. Calculate the corrected length and the length correction factor.
LC = L + 70
= 250 + 70
= 320 m
LC
C=
L
320
=
250
= 1,28
4. Tension to move the empty belt.
TX = 9,8G x fX x LC
= 9,8 x 55 x 0,022 x 320
= 3794 N
5. Tension to move the load horizontally.
TX = 9,8Q x fY x LC
= 9,8 x 79,4 x 0,027 x 320
= 6723 N
6. Tension to lift the load.
TZ = 9,8Q x H
= 9,8 x 79,4 x 20
= 15562 N
7. No accessories are present and therefore the tension to overcome the resistance of accessories is zero.
8. Effective tension.
Te = T X + T Y + T Z + T U
= 3794 + 6723 + 15562 + 0
= 26079 N
9. The absorbed power
P = Te x S
= 26079 x 1,4
= 36511W
10. The slack side tension.
Slack side tension to prevent slip.
The drive factor for 210 degree wrap and lagged pulley with a gravity take-up, as given in Table 11, is 0,38.
Tm = k x T e
= 0,38 x 36079
= 9910 N
Slack side tension to limit sag to 2%. The sag factor for 2% sag is 6,3 and the estimated belt mass for a medium load and 900
mm belt width, as given in Table 8, is 11,1kg/m.
TS = 9,8Sf (B + Q) x ld
= 9,8 x 6,3 x (11,1 + 79,4) x 1,2
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/Dunlop/Belting%20B... 24/05/2004
Dunlop Conveyor Belt Design Manual Page 9 of 33
= 6705 N
Th = 9,8B x H
= 9,8 x 11,1 x 20
= 2176 N
12. The maximum belt tension
T 1 = Te + T 2 + T h
= 26079 + 9910 + 2176
= 38165 N
Effective tension.
T1
T=
W
38165
=
900
= 42,4 N/mm
= 42,4 kN/m
b Width between skirtplates m T1 Maximum belt tension across full belt width N
fx Friction coefficient for empty belt Tus Tension to overcome resistance of skirtboards N
fy Friction coefficient for loaded belt Tx Tension to move the empty belt N
H Change in elevation along conveyor length m Tz Tension to lift (or lower) the load N
24/05/2004
Dunlop Conveyor Belt Design Manual Page 10 of 33
Charcoal MA N 0,35 25 22
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/Dunlop/Belting%20B... 24/05/2004
Dunlop Conveyor Belt Design Manual Page 11 of 33
Flaxseed MA O 0,70 10 12
Fluorspar MA N 1,70 30 20
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/Dunlop/Belting%20B... 24/05/2004
Dunlop Conveyor Belt Design Manual Page 12 of 33
Slate MA N 1,36 20 18
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/Dunlop/Belting%20B... 24/05/2004
Dunlop Conveyor Belt Design Manual Page 13 of 33
Starch NA GF 0,60 10 12
Characteristics
Cover Grade
Angle of Angle of
Material Characteristics
Surcharge α Repose
5° 0° - 19° Uniform Size
10° 20° - 29° Rounded, dry ,medium weight
20° 30° - 34° Granular lumpy (Coal, Clay)
25° 35° - 39° Coal, stone, ores
30° 40° - 45° Irregular (wood chips)
1. The cross sectional area of the load which can be carried without spillage.
2. The belt speed.
3. The material density.
The cross sectional area is influenced by many factors including the flowability of the material, the angle of surcharge and the incline angle
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/Dunlop/Belting%20B... 24/05/2004
Dunlop Conveyor Belt Design Manual Page 14 of 33
at the load point of the conveyor. To achieve optimum load area the loading chutes must be designed to ensure the most advantageous
initial load shape and this can only be achieved if:
To ensure that the optimum load shape is maintained along the entire belt length:
Where
M = 0,3145W - 3,2 - Bc
Where
Recommended
Belt Max. Lump Size Trough Area of Speed m/s
Width Angle Load
mm Sized Unsized Degrees m2 0,5 0,8 1,2 1,6 2,0 2,5 3,0
mm mm
600 125 200 20 0,033 59 95 142 190 236 297 357
27½ 0,037 66 106 160 213 266 333 400
30 0,038 69 110 164 218 274 342 410
35 0,040 72 115 173 230 288 360 432
45 0,042 76 121 181 242 303 378 436
750 150 250 20 0,054 97 156 233 311 389 486 583
27½ 0,060 109 173 259 346 432 540 648
30 0,062 112 179 268 357 446 558 670
35 0,065 117 187 281 375 468 585 702
45 0,068 122 196 294 392 490 612 734
900 175 300 20 0,080 144 230 346 461 576 720 864
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/Dunlop/Belting%20B... 24/05/2004
Dunlop Conveyor Belt Design Manual Page 15 of 33
TABLE 4 RECOMMENDED MAXIMUM BELT SPEEDS FOR NORMAL USE (METRES PER SECOND)*
Belt Width Grain or Other Run of Mine Hard Ores and Stone -
(mm) Free Flowing Material Coal and Earth + Primary Crushed ++
300 2,5 1,5 1,5
400 2,5 2,0 1,8
500 3,0 2,0 1,8
600 3,0 2,5 2,3
750 3,6 3,0 2,8
900 4,0 3,3 3,0
1050 4,0 3,6 3,0
1200 4,6 3,6 3,3
1350 5,0 3,6 3,3
1500 5,0 3,6 3,3
1800 4,0 3,8
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/Dunlop/Belting%20B... 24/05/2004
Dunlop Conveyor Belt Design Manual Page 16 of 33
* These speeds are intended as guides to general practice and are not absolute.
+ Moderately abrasive materials.
++ Very abrasive materials.
Note: In the case of belts loaded on inclines of 100 or more it may be necessary to reduce the above speeds in order to achieve maximum
capacity.
3% 4,2
2% 6,3
1,5% 8,4
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/Dunlop/Belting%20B... 24/05/2004
Dunlop Conveyor Belt Design Manual Page 17 of 33
Operating Conditions
Belt Width
(mm) Light Duty Medium Duty Heavy Duty
(kg/m) (kg/m) (kg/m)
500 4,1 6,2 10,3
600 5,0 7,4 12,3
750 6,2 9,3 15,5
900 7,4 11,1 18,5
1050 8,6 13,0 21,6
1200 9,8 14,8 24,7
1350 11,0 16,7 27,8
1500 12,3 18,6 30,9
1650 13,5 20,5 33,9
1800 14,7 22,3 37,0
2100 17,2 26,0 43,3
2200 18,0 27,3 45,3
Note:
The values given in the table are estimated values for use in the calculation of maximum belt operating tension necessary to make the
correct belt selection. When the belt specification has been determined, the mass should be checked more accurately from Table 17. If the
actual mass of the specification differs considerably from the approximate value obtained from the table the tension calculation should be
rechecked using the more accurate belt mass.
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/Dunlop/Belting%20B... 24/05/2004
Dunlop Conveyor Belt Design Manual Page 18 of 33
Notes:
1. When calculating the driving tension required for dual drive units, the drive factor selected must correspond to the total angle of
driving wrap.
2. The drive factors quoted for gravity or automatic take-up systems are minimum values based on the relationship between angle of
wrap and coefficient of friction between belt and drum at the point of slip. In the case of screw take-up units, an adjustment has
been made to the drive factor to allow for the extra tension which may be induced in the belt either:
a. to compensate for the effect of belt elongation when the material is loaded.
3. In those cases where an electrically or hydraulically loaded winch type take-up is used, where the induced tension can be preset
and controlled, the drive factor should be selected to correspond with a gravity take-up system.
Tensile strength
The belt class required is that which has an operating tension greater than or equal to the calculated maximum unit tension T. (Table 12).
Load support
Choose the lowest class which meets the tensile strength requirement. Looking at Table 14, determine which load category best describes
the load being conveyed i.e. A, B, C, D or E category load. The value obtained at the intersection of the belt specification row and the load
category column gives the maximum width at which that belt specification can be used.
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/Dunlop/Belting%20B... 24/05/2004
Dunlop Conveyor Belt Design Manual Page 19 of 33
Additional Information
Belt modulus
Refer to Table 20 for belt modulus.
Belt mass
The mass of a particular belt construction can be determined by adding the carcass mass found in Table 17 to the combined mass of covers
found in Table 18. This will give the mass per unit area. To calculate the mass per unit length multiply by the belt width in metres.
Belt thickness
The belt thickness can be obtained from the information given in Table 16.
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/Dunlop/Belting%20B... 24/05/2004
Dunlop Conveyor Belt Design Manual Page 20 of 33
Recommended maximum belt width (mm) for correct load support. Multi-ply textile reinforced rubber belting.
A B C D E
Light Duty Light to Medium Duty Medium Duty Heavy Duty Extra Heavy Duty
Belt Spec
Up to 800 kg/m3 Up to 1200 kg/m3 Up to 1600 kg/m3 Up to 2400 kg/m3 Up to 3000 kg/m3
- 25mm Lumps - 50mm Lumps - 100mm Lumps - 250mm Lumps + 250mm Lumps
160/2 750 600 500 400 Not Recommended
200/2 750 600 600 4500 Not Recommended
250/2 900 750 750 600 500
250/3 1050 900 750 600 600
315/2 900 900 750 600 500
315/3 1200 1050 1050 750 600
400/2 1200 1050 1050 900 750
400/3 1200 1050 1050 900 750
400/4 1500 1500 1350 900 750
500/2 1200 1200 1200 1050 900
500/3 1350 1200 1200 1050 900
500/4 1650 1500 1350 1200 900
500/5 1800 1800 1800 1500 1350
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/Dunlop/Belting%20B... 24/05/2004
Dunlop Conveyor Belt Design Manual Page 21 of 33
TABLE 15 MAXIMUM NUMBER OF PLIES RECOMMENDED FOR CORRECT EMPTY BELT TROUGHING
2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 20°
160
2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 35°
2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 20°
200
2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 35°
- 3 3 3 3 3 3 3 3 3 3 3 3 3 3 20°
250
- 2 2 2 3 3 3 3 3 3 3 3 3 3 3 35°
- 2 3 3 3 4 4 4 4 4 4 4 4 4 4 20°
315
- 2 3 3 3 3 4 4 4 4 4 4 4 4 4 35°
- 2 4 4 4 4 4 4 4 4 4 4 4 4 4 20°
400
- - 3 3 3 4 4 4 4 4 4 4 4 4 4 35°
- - 4 4 4 4 4 4 4 4 4 4 4 4 4 20°
500
- - 3 3 3 4 4 4 4 4 4 4 4 4 4 35°
- - 4 4 4 4 4 4 4 4 4 4 4 4 4 20°
630
- - 2 2 3 4 4 4 4 4 4 4 4 4 4 35°
- - 3 3 4 4 4 4 4 4 4 4 4 4 4 20°
800
- - 2 2 3 4 4 4 4 4 4 4 4 4 4 35°
- - - - 4 4 4 4 4 4 4 4 4 4 4 20°
1000
- - - - 2 3 4 4 4 4 4 4 4 4 4 35°
- - - - 4 4 4 4 4 4 4 4 4 4 4 20°
1250
- - - - 3 3 4 4 4 4 4 4 4 4 4 35°
- - - - 3 4 4 4 4 4 4 4 4 4 4 20°
1600
- - - - - 3 4 4 4 4 4 4 4 4 4 35°
- - - - - 4 5 5 5 5 5 5 5 5 5 20°
2000
- - - - - - 4 4 5 5 5 5 5 5 5 35°
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/Dunlop/Belting%20B... 24/05/2004
Dunlop Conveyor Belt Design Manual Page 22 of 33
Add the thickness of the covers to get the total belt thickness
To obtain total belt mass add the mass of the combined covers from Table 18.
The mass per unit length is determined by multiplying the total mass by the belt width in metres.
Mass Mass
Grade of Cover Grade of Cover
(kg/m2) (kg/m2)
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/Dunlop/Belting%20B... 24/05/2004
Dunlop Conveyor Belt Design Manual Page 23 of 33
The rate at which a belt cover wears is related to the thickness of the cover and to the impact energy imparted by material lumps.
Impact energy can be calculated for any material of known lump mass and vertical velocity.
γ - ω x νv J
Non abrasive material Abrasive material Very abrasive material Very sharp abrasive material
such as lime, charcoal, such as salt, anthracite such as slag, copper ore, such as quartz, some ores,
Cycle
wood chips, bituminous coal, phosphate rock, sinter, coke sand, foundry refuse, glass batch,
time
coal grain limestone, fullers earth flue dust iron borings
s
Lump size (mm) Lump size (mm) Lump size (mm) Lump size (mm)
dust 12 50 150 dust 12 50 150 dust 12 50 150 dust 12 50 150
to to to and to to to and to to to and to to to and
12 50 150 over 12 50 150 over 12 50 150 over 12 50 150 over
12 2,0 3,0 6,0 8,0 3,0 6,0 10,0 10,0 6,0 10,0 10,0 10,0 8,0 10,0 10,0 10,0
25 2,0 2,5 3,0 5,0 2,5 3,0 6,0 10,0 3,0 6,0 10,0 10,0 4,0 8,0 10,0 10,0
40 1,0 2,5 3,0 5,0 2,5 3,0 4,0 5,0 3,0 3,0 6,0 10,0 3,0 4,0 8,0 10,0
60 1,0 2,5 3,0 5,0 2,5 3,0 4,0 5,0 3,0 3,0 5,0 6,0 3,0 3,0 6,0 10,0
90 1,0 2,5 3,0 5,0 2,5 3,0 4,0 5,0 3,0 3,0 5,0 5,0 3,0 3,0 6,0 6,0
120 1,0 2,5 3,0 5,0 2,5 3,0 4,0 5,0 3,0 3,0 4,0 5,0 3,0 3,0 5,0 6,0
180 1,0 2,5 3,0 5,0 2,5 3,0 4,0 5,0 3,0 3,0 4,0 5,0 3,0 3,0 5,0 6,0
240+ 1,0 2,5 3,0 5,0 2,0 3,0 4,0 5,0 3,0 3,0 4,0 5,0 3,0 3,0 5,0 6,0
Multi-ply
Steelcord
Textile Solid Woven
Belt Class Reinforced
Reinforced PVC Belting
Rubber Belting
Belting
160 1060
200 1330
250 1660
315 2070 1750
400 2950 2220
500 3330 2800 29000
630 4200 3500 37700
800 5330 4440 47900
1000 6660 5550 59800
1250 8330 6900 74800
1600 10660 8890 95800
2000 13330 11110 119700
2500 149700
3150 188600
4000 240000
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/Dunlop/Belting%20B... 24/05/2004
Dunlop Conveyor Belt Design Manual Page 24 of 33
5000 300000
6300 377200
TABULATOR CALCULATIONS
The tabulation method described below is a convenient means of calculating the tensions at any point on the conveyor.
Blank copies of the "Conveyor Tabulation Sheets" are available from Dunlop Africa Industrial Products.
The following method is used to determine the tension at any point along the conveyor:
It may be found that the value of T2 obtained when the maximum effective tension has been calculated is different to that used in the
calculations. If this is the case the new T2 value is used to calculate tensions at each point.
Steps 7, 8 and 9 should be repeated for four load cases viz empty, fully loaded, non-declined sections loaded and declined sections loaded.
EXAMPLE
Step 1
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/Dunlop/Belting%20B... 24/05/2004
Dunlop Conveyor Belt Design Manual Page 25 of 33
L + 70
C=
L
570
=
500
= 1,14
Step 2
From Table 10 the mass of the moving parts for a 1200 mm wide conveyor of medium duty is 71 kg/m.
Step 3
τ
Q= 0,278
s
0,278 x 4500
=
3,5
= 357,4 kg/m
Step 4
Calculate the maximum effective tension when the non-declined sections of the conveyor are all carrying load and the declined sections
have no load. The total horizontal length of non-declined sections is 20 + 330 = 350 m.
The overall change in elevation on the non-declined sections is 70 in. Note that the actual length of the conveyor is used to calculate Tx and
only the loaded length to calculate Ty. The length correction factor is a constant and is used to convert the actual length to a corrected
length. The friction factors are determined by the total conveyor length in all cases.
Tx = 9,8G x fx C x L
= 9,8 x 71 x 0,020 x 1,14 x 500
= 7932N
Ty = 9,8Q x fy C x L
= 9,8 x 357,4 x 0,020 x 1,14 x 350
= 30745N
Tz = 9,8Q x H
= 9,8 x 357,4 x 70
= 245176N
Effective tension to overcome skirtboard friction The inter-skirtboard width is assumed to be 2/3 of the belt width i.e. 0,8 m.
9,8fs x Q x Ls
Tus =
S x b2
9,8 x 357,4 x 0,020 x 1,14 x 350
=
3,5 x 0,64
= 3050N
Te = Tx + Ty + Tz + Tus
= 7932 + 30745 + 245176 + 3050
= 286903N
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/Dunlop/Belting%20B... 24/05/2004
Dunlop Conveyor Belt Design Manual Page 26 of 33
Step 5
Tm = k x T e
k = 0,38 from Table 11 and hence
Tm = 0,38 x 286903
= 109023
The minimum slack side tension to prevent excessive belt sag is:
Ts = 9,8Sf x (B + Q) x Id
= 9,8 x 6,3 x (14,8 + 357,4) x 1,2
= 27576N
Since
Tm > Ts
T2 = Tm
i.e. T2 = 109023N
Step 6
Step 7
Calculations of the effective tension for each segment (or run) is shown on Sheet 1 for the empty belt, Sheet 2 for the fully loaded belt,
Sheet 3 for the case where only non-decline sections are loaded and Sheet 4 where only the decline sections are loaded.
Step 8
The accumulated effective tension column is the sum of the effective tensions of the current segment and all preceeding segments.
Step 9
The total effective tension for each load case is the value in the last row of the column titled 'Accumulated Effective Tension'.
The reason for the difference between the effective tension determine step 4 and that on Sheet 3 is the more accurate figures used for mass
of the moving parts on the tabulation sheets.
The tension at any point along the conveyor can now be determined, all load cases, by adding the effective tension at the point to the slope
tension at the point and then adding the worst case T2 value.
The highest Te value occurs when all non-declines are loaded. i.e. Te = 283609N
Tm = k x T e
= 0,38 x 283609N
= 107771N
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/Dunlop/Belting%20B... 24/05/2004
Dunlop Conveyor Belt Design Manual Page 27 of 33
T2 = Tm
i.e. T2 = 107771N
Thus, for example, the effective tension at run L - M takes the following values:
From these it is determined that the tension at point M under the four cases, given by
Te + T2 + Th is
Empty belt
4302 + 107771 + 0
= 112073N
-24577 + 107771 + 0
= 83194N
Non-declines loaded
6059 + 107771 + 0
= 113830N
Declines loaded
-26334 + 107771 + 0
= 81437N
Friction Factors
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/Dunlop/Belting%20B... 24/05/2004
Dunlop Conveyor Belt Design Manual Page 28 of 33
Correction factor C 1,14 Rotating Parts Mass M 19,9 17,1 22,9 kg/set
Friction Factors
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/Dunlop/Belting%20B... 24/05/2004
Dunlop Conveyor Belt Design Manual Page 29 of 33
Friction Factors
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/Dunlop/Belting%20B... 24/05/2004
Dunlop Conveyor Belt Design Manual Page 30 of 33
Friction Factors
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/Dunlop/Belting%20B... 24/05/2004
Dunlop Conveyor Belt Design Manual Page 31 of 33
Friction Factors
TENSION TABULATOR
VERTICAL CURVES
It is necessary to calculate the tension at the point under consideration following the method described in Tabulator Calculations.
Concave curves
The worst condition exists when the belt is loaded to the start of the curve and under these conditions the minimum radius of curvature to
prevent the belt lifting off the idlers is
113 Tp
R=
B
Where
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/Dunlop/Belting%20B... 24/05/2004
Dunlop Conveyor Belt Design Manual Page 32 of 33
Sinβ x W x E
R=
4494 (tr - tc)
Sinβ x W x E
R=
8988 (tr - 5,2)
3. Maximum allowable change of incline per idler to prevent overstress of belt edges
The curve must be designed with a radius at least large enough to satisfy conditions 1 and 2 and the idler spacing must ensure that
conditions 3 and 4 are satisfied.
Belt length:
π(D + d)N
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/Dunlop/Belting%20B... 24/05/2004
Dunlop Conveyor Belt Design Manual Page 33 of 33
L= 2
or
Assuming the length of belt is large and the thickness not Where d 0,3m for general stock belting and up to 0,5m for
abnormally small, then the core diameter can be neglected in heavy rolls of belting, such as steelcord belting or very wide
approximate calculations. belts.
Imperial to metric
in2 cm2
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/Dunlop/Belting%20B... 24/05/2004
Page 1 of 1
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/dunlop/belting%20b6.1... 7/06/2004
Page 1 of 1
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/dunlop/belting%20b6.1... 7/06/2004
Page 1 of 1
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/dunlop/belting%20b6.1... 7/06/2004
Page 1 of 1
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/dunlop/belting%20b6.1... 7/06/2004
Page 1 of 1
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/dunlop/belting%20b6.1... 7/06/2004
Page 1 of 1
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/dunlop/belting%20b6.1... 7/06/2004
Page 1 of 1
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/dunlop/belting%20b6.1... 7/06/2004
Page 1 of 1
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/dunlop/belting%20b6.1... 7/06/2004
Page 1 of 1
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/dunlop/belting%20b6.1... 7/06/2004
Page 1 of 1
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/dunlop/belting%20b6.1... 7/06/2004
Page 1 of 1
http://www.ckit.co.za/Secure/Conveyor/Troughed/belt_tension/dunlop/belting%20b6.1... 7/06/2004