Professional Documents
Culture Documents
Asce 70-5 Wind
Asce 70-5 Wind
xls" Program
Version 1.2
Input Data:
If z <= 15 then: Kz = 2.01*(15/zg)^(2/α) , If z > 15 then: Kz = 2.01*(z/zg)^(2/α) (Table 6-3, Case 2a)
α= 9.50 zg = 900 (Table 6-2)
Kh = 1.25 (Kh = Kz evaluated at z = h)
I= 1.15 (Table 6-1) (Importance factor)
Velocity Pressure: qz = 0.00256*Kz*Kzt*Kd*V^2*I (Sect. 6.5.10, Eq. 6-15)
qh = 22.58 psf qh = 0.00256*Kh*Kzt*Kd*V^2*I (qz evaluated at z = h)
Ratio h/L = 1.898 freq., f = 1.657 hz. (f >= 1, Rigid structure)
Gust Factor, G = 0.850 (Sect. 6.5.8)
Design Net External Wind Pressures (Sect. 6.5.12.2):
p = qz*G*Cp - qi*(+/-GCpi) for windward wall (psf), where: qi =qh (Eq. 6-17, Sect. 6.5.12.2.1)
p = qh*G*Cp - qi*(+/-GCpi) for leeward wall, sidewalls, and roof (psf), where: qi = qh (Sect. 6.5.12.2.1)
1 of 4 4/12/2011 6:56 AM
"ASCE705W.xls" Program
Version 1.2
Normal to Ridge Wind Load Tabulation for MWFRS - Buildings of Any Height
Surface z Kz qz Cp p = Net Design Press. (psf)
(ft.) (psf) (w/ +GCpi) (w/ -GCpi)
Windward Wall 0 0.85 15.35 0.80 6.37 14.50
15.00 0.85 15.35 0.80 6.37 14.50
20.00 0.90 16.31 0.80 7.02 15.15
25.00 0.95 17.09 0.80 7.56 15.69
30.00 0.98 17.76 0.80 8.01 16.14
35.00 1.01 18.34 0.80 8.41 16.54
40.00 1.04 18.87 0.80 8.76 16.90
45.00 1.07 19.34 0.80 9.09 17.22
50.00 1.09 19.78 0.80 9.38 17.51
55.00 1.12 20.18 0.80 9.65 17.79
60.00 1.14 20.55 0.80 9.91 18.04
70.00 1.17 21.23 0.80 10.37 18.50
80.00 1.21 21.83 0.80 10.78 18.91
90.00 1.24 22.38 0.80 11.15 19.28
For z = hr: 98.00 1.26 22.79 0.80 11.43 19.56
Notes: 1. (+) and (-) signs signify wind pressures acting toward & away from respective surfaces.
2. Per Code Section 6.1.4.1, the minimum wind load for MWFRS shall not be less than 10 psf.
3. References : a. ASCE 7-02, "Minimum Design Loads for Buildings and Other Structures".
b. "Guide to the Use of the Wind Load Provisions of ASCE 7-02"
by: Kishor C. Mehta and James M. Delahay (2004).
2 of 4 4/12/2011 6:56 AM
"ASCE705W.xls" Program
Version 1.2
Parameters Used in Both Item #2 and Item #3 Calculations (from Table 6-2):
α^ = 0.105
b^ = 1.00
α(bar) = 0.154
b(bar) = 0.65
c= 0.20
l= 500 ft.
ε(bar) = 0.200
z(min) = 15 ft.
3 of 4 4/12/2011 6:56 AM
"ASCE705W.xls" Program
Version 1.2
Figure 6-9 - Design Wind Load Cases of MWFRS for Buildings of All Heights
Case 1: Full design wind pressure acting on the projected area perpendicular to each principal axis of
the structure, considered separately along each principal axis.
Case 2: Three quarters of the design wind pressure acting on the projected area perpendicular to each
principal axis of the structure in conjunction with a torsional moment as shown, considered
separately for each principal axis.
Case 3: Wind pressure as defined in Case 1, but considered to act simultaneously at 75% of the
specified value.
Case 4: Wind pressure as defined in Case 2, but considered to act simultaneously at 75% of the
specified value.
Notes: 1. Design wind pressures for windward (Pw) and leeward (PL) faces shall be determined in
accordance with the provisions of Section 6.5.12.2.1 and 6.5.12.2.3 as applicable for buildings
of all heights.
2. Above diagrams show plan views of building.
3. Notation:
Pwx, Pwy = Windward face pressure acting in the X, Y principal axis, respectively.
PLx, PLy = Leeward face pressure acting in the X, Y principal axis, respectively.
e (e x, ey) = Eccentricity for the X, Y principal axis of the structure, respectively.
MT = Torsional moment per unit height acting about a vertical axis of the building.
4 of 4 4/12/2011 6:56 AM