Professional Documents
Culture Documents
It is important to identify the details of network sections and devices that will be
affected or involved in a new design. This information is included in which section of the
Network Design Requirements Document?
Project Goal
Project Scope
Technical Requirements
2. Which two pieces of information does the network designer need to determine if the
Cisco IOS of a router requires an upgrade? (Choose two.)
3. Which three pieces of information need to be considered when selecting the proper
Cisco IOS version for an upgrade? (Choose three.)
processor ID
interface type
amount of DRAM
bootstrap version
4. What are two practices a network technician should follow when installing a new
interface card in
a router? (Choose two.)
Be sure the interface card faceplate does not touch the chassis rear panel.
Do not tighten the captive screws until the router has been powered on and recognizes the
card.
Store the blank faceplate inside the card slot to be used if the card is removed.
Push the interface card into place until the edge connector is seated securely
5. The new serial interface card for the router arrives and the network technician reads
that it is hotswappable. What does this mean?
The card cannot be installed while the router is powered on because static discharge
could damage the card.
The card cannot be installed until the router is powered off and completely cooled down.
The card can be installed while the router is powered on if the router supports this
technology.
The card is a replacement and must be installed in the same slot as the card it is
replacing.
6. Refer to the exhibit. A network administrator issues the command shown to gain
knowledge about a poorly documented network. Which two pieces of information can the
network administrator discover from the command output? (Choose two.)
The entire network contains a total of five Cisco devices with CDP enabled.
None of the directly connected network devices have been configured with an IP address.
Five Cisco devices with CDP enabled are directly connected to device C3750-24_MDF
7. Refer to the exhibit. Which of the three Cisco IOS images shown will load into RAM?
The router selects an image depending on the value of the configuration register.
The router selects the third Cisco IOS image because it is the most recent IOS image.
The router selects the second Cisco IOS image because it is the smallest IOS image.
The router selects an image depending on the boot system command in the configuration.
The router selects the third Cisco IOS image because it contains the advipservicesk9
image.
8. An administrator wants to download a new Cisco IOS software version to the local
router. Which
command performs this task?
9. Refer to the exhibit. The top of the output shows the Cisco Feature Navigator
regarding a Cisco IOS image that the administrator wants to install on a router. Below it
is the output from the show version command for that router. Which statement is true
regarding the capacity of the router to run this Cisco IOS image?
10. Which two items are objectives of a WLAN design site survey? (Choose two.)
11.Refer to the exhibit. Which two actions improve the weaknesses of the topology
shown, assuming that each access layer segment is in its own subnet? (Choose two.)
Implement a reduntant link from all access layer switches to Admin, Dist, and Server
Farm.
Implement a backup firewall with a link to a secondary ISP and implement a redundant
link to the DMZ.
Implement reduntant links from the existing firewall to all access layer switches.
12. A company is beginning to analyze their new Cisco IOS upgrade requirements. What
is one of the router components that a network administrator must consider when
selecting a new Cisco IOS version?
processor type
compatibility of the bootstrap version with the new Cisco IOS software
13. An employee at a company notices that the wireless signal strength indicator on his
laptop fluctuates from good to low. The network administrator decides to do a site survey
of that area. Which three factors need to be included in the survey? (Choose three.)
location of the AP
14. The new network design for AnyCompany must include support of voice and video
traffic. Before upgrading, the network designer checks whether the existing devices can
support the new requirements. Which three items does the designer need to check?
(Choose three.)
15. A new Cisco IOS version has been copied into flash from a TFTP server. When a
reload is issued to upgrade the Cisco IOS, the router freezes part of the way through the
loading process. What could be the problem?
The new Cisco IOS should have been loaded into NVRAM.
The new bootstrap version is not compatible with the original version on the router.
16. Refer to the exhibit. A network designer has no documentation and is attempting to
create a logical diagram of the network using the output from show commands. What can
be determined from the output shown?
17. A production router is reloaded and finishes with a Router> prompt. What three facts
can be determined? (Choose three.)
The router did not locate the Cisco IOS in flash, so it defaulted to ROM.
18. During a site survey, the network designer noticed that people were accessing the
company wireless network from the parking lot. What should be done to stop the wireless
signal from radiating out into the parking lot?
19. A network design project includes a review of the existing network. What is the
purpose of this phase of the project?
lower the cost of the project by removing redundant links and devices
determine if the number of applications used within the company can be reduced
To determine what existing network devices require upgrades to meet the new
20. Refer to the exhibit. Based upon the Cisco IOS file naming convention, what is
represented by
the value ipvoicek9 listed in the IOS filename?
version
file format
feature set
hardware platform
21 Refer to the exhibit. What two items can be determined from the output? (Choose
two.)
23 Refer to the exhibit. The network administrator is attempting to install a new version
of the IOS on R2. Based on the exhibited output, what are two possible reasons that the
transfer failed?(Choose two.)
The administrator did not enable TFTP on R2.
The administrator did not verify that the TFTP server is running.
network requirements
project scope