Professional Documents
Culture Documents
Ccna Discovery 40 Final 3rd Module
Ccna Discovery 40 Final 3rd Module
Close Window
Assessment System
Exam Viewer - DRSEnt Final - CCNA Discovery: Introducing Routing and Switching in the Enterprise (Version
4.0)
Below you will find the assessment items as presented on the exam as well as the scoring rules associated with the item.
Use of the exam information in the Exam Viewer is subject to the terms of the Academy Connection Website Usage Agreement between you
and Cisco. The purpose of the Exam Viewer is to support instruction while not compromising exam security for other Cisco Networking
Academies or students. This material should not be distributed outside a proctored and controlled setting. If misuse is found, action will be
taken to limit access to assessment content. Please remember to logout and close your browser window after using the Exam Viewer.
31
Refer to the exhibit. Both routers are configured to use the EIGRP routing protocol. However, when the show ip eigrp neighbors
command is issued at R1, the output displays that the routers are unable to establish adjacency. What is the possible cause of this
problem?
EIGRP routing is incorrectly configured at R1.
The autonomous system number is the same on both routers.
The no auto-summary command is applied on both routers.
The IP address of the serial interfaces of both routers is incorrectly configured.
Max Value = 2
Max Value = 2
Refer to the exhibit. Which VTP function will this switch perform?
It will create, change and share local VLAN information with other switches in the XYZ domain.
It will forward to other switches the VLANs that are created in Switch1.
It will back up the VTP database for domain XYZ.
It will forward VTP configuration information for domain XYZ.
Max Value = 2
Max Value = 2
Max Value = 2
Max Value = 2
Refer to the exhibit. All routers are configured to use OSPF with the default configuration. The network administrator wants to ensure
that R1 will be the DR when the routers are booted.
What are two ways the network administrator could accomplish this goal?
Configure the OSPF priority value of the Fa0/0 interface of R1 to 0.
Configure the router ID of R2, R3, and R4 to a higher value than R1.
Change the priority value of the Fa0/0 interface of R2, R3, and R4 to 255.
Configure a loopback interface on R1 with an IP address higher than any IP
address on the other routers.
Configure the OSPF priority value of the Fa0/0 interface of R1 to a higher value than the Fa0/0 interface of any other router.
Max Value = 2
Max Value = 2
Refer to the exhibit. A network administrator wants to block Telnet sessions from host B to hosts E and F. Where should ACL 110 be
placed if the administrator follows Cisco best practices?
on the Fa0/0 interface of R1 inbound
on the S0/0/0 interface of R1 inbound
on the S0/0/0 interface of R3 outbound
on the Fa0/0 interface of R3 inbound
Max Value = 2
Max Value = 2
Refer to the exhibit. The network administrator has used classless routing in the network. What is the result of running the displayed
command?
All packets that are destined for address 10.12.0.1/22 will be forwarded via serial0/0/0.
All packets that are destined for address 10.12.14.0/22 will be forwarded via serial0/0/0.
All packets that are destined for address 10.12.16.1/22 will be forwarded via serial0/0/0.
All packets that are destined for address 10.12.15.255/22 will be forwarded via serial0/0/0.
Max Value = 2
Max Value = 2
Refer to the exhibit. All switches are configured with default bridge priority. Which two ports will definitely be elected STP designated
ports if all links are operating at the same bandwidth? (Choose two.)
Fa0/1 interface of switch A
Fa0/2 interface of switch A
Fa0/2 interface of switch B
Fa0/1 interface of switch C
Fa0/2 interface of switch C
Max Value = 2
Max Value = 2
Max Value = 2
Max Value = 2
Refer to the exhibit. How will Switch2 respond to the VTP advertisement sent by Switch1?
It will ignore the VTP advertisement.
It will add two VLANs to its database.
It will change its configuration revision number to 4.
It will send the VTP advertisement to Switch1 to delete the two VLANs.
Max Value = 2
Max Value = 2
Refer to the exhibit. Both switches have been configured with static VLANs. Host A and host C belong to one VLAN and host B and D
belong to another VLAN. However, the hosts within the same VLAN are unable to communicate with each other.
Max Value = 2
It immediately transitions all ports that are not discarding to the forwarding state.
It provides a mechanism for disabling redundant links in a switched network.
It has three port states: discarding, learning, and forwarding.
It ensures that there are no loops in the switched network.
It converges the switched network in less than 1 second.
Max Value = 2
Refer to the exhibit. The network administrator configures R1 as displayed. However, some hosts from Network A are unable to access
the Internet. Which two actions can resolve this problem? (Choose two.)
Configure the ip nat inside and ip nat outside commands on the correct interfaces.
Increase the number of IP addresses in the NAT address pool.
Configure the Fa0/0 interface of R1 for a different subnet.
Use PAT instead of dynamic NAT.
Use static NAT.
Max Value = 2
Max Value = 2
Max Value = 2
Refer to the exhibit. R1 is using the default OSPF operation. Which IP address will be used as the router ID of R1?
192.168.201.1
172.16.1.1
10.10.10.1
10.1.1.1
Max Value = 2
Max Value = 2
Refer to the exhibit. None of the hosts in network A are able to access the Internet. How can this problem be resolved?
Configure dynamic NAT instead of PAT.
Configure the access list for the correct network.
Include the ip nat pool command in the configuration.
Configure the ip nat inside command on the correct interface.
Max Value = 2
Max Value = 2
Reset View
Close Window
All contents copyright ©2001-2008 Cisco Systems, Inc. All rights reserved. Privacy Statement and Trademarks.