Professional Documents
Culture Documents
TDA1562
TDA1562
DATA SHEET
Philips Semiconductors
Preliminary specication
TDA1562Q
Quick start option (e.g. car-telephony/navigation) Low (delta) offset voltage at the outputs Load dump protection Short-circuit safe to ground, supply voltage and across the load Low power dissipation in any short-circuit condition Protected against electrostatic discharge Thermally protected Flexible leads.
The TDA1562Q is a monolithic integrated 70 W/4 Bridge-Tied Load (BTL) class-H high efficiency power amplifier in a 17-lead DIL-bent-SIL plastic power package. The device can be used for car audio systems (e.g. car, radio and boosters) as well as mains fed applications (e.g. midi/mini audio combinations and TV sound).
QUICK REFERENCE DATA Test conditions: VP = 14.4 V; RL = 4 ; Rs = 0 ; f = 1 kHz; Tamb = 25 C; unless otherwise specied. SYMBOL VP PARAMETER supply voltage CONDITIONS operating non-operating load dump Iq(tot) Istb VOO VOO Gv Zi(dif) Po THD total quiescent current standby current output offset voltage delta output offset voltage voltage gain differential input impedance output power total harmonic distortion THD = 0.5% THD = 10% Po = 1 W Po = 20 W DDD active SVRR CMRR ISRR Vn(o) supply voltage ripple rejection common mode rejection ratio input signal rejection ratio noise output voltage on and mute on mute on on and mute; RL = open circuit standby on and mute on mute 8 25 90 45 60 60 70 80 MIN. 110 1 26 150 55 70 0.03 0.06 10 70 80 90 100 TYP. 14.4 MAX. 18 30 45 150 50 100 30 27 150 V V V mA A mV mV dB k W W % % % dB dB dB V UNIT
1998 Apr 07
Philips Semiconductors
Preliminary specication
TDA1562Q
VERSION SOT243-1
C1+ 5
VP1 9
VP2 10
status I/O
16
TEMPERATURE SENSOR
mode select
disable LIFT-SUPPLY
CURRENT PROTECTION
75 k
TDA1562Q
LOAD DETECTOR
diagnostic
PREAMP +
11
OUT
Vref
14 15 k disable
signal 17 GND
reference voltage
MGL264
15 C2
13 C2+
6 PGND1
12 PGND2
1998 Apr 07
Philips Semiconductors
Preliminary specication
TDA1562Q
handbook, halfpage
TDA1562Q
1998 Apr 07
Philips Semiconductors
Preliminary specication
TDA1562Q
1. LOW, fast mute: the circuit remains switched on, but the input signal is suppressed 2. MID, class-B: the circuit operates as class-B amplifier, the high power supply voltage is disabled, independent of the case temperature 3. HIGH, class-H: the circuit operates as class-H amplifier, the high power supply voltage is enabled, independent of the case temperature. When the circuit is switched from fast mute to class-B/H or vice versa the switching is immediately carried out. When the circuit is switched from class-B to class-H or vice versa the actual switching takes place at a zero crossing of the input signal. OUTPUT This output has 3 possibilities: 1. LOW, mute: acknowledge of muted amplifier 2. MID, class-B: the circuit operates as class-B amplifier, the high power supply voltage is disabled, caused by the case temperature Tc > 120 C 3. HIGH, class-H: the circuit operates as class-H amplifier, the high power supply voltage is enabled, because the case temperature Tc < 120 C. When the circuit is switched from class-B to class-H or vice versa the actual switching takes place at a zero crossing of the input signal. The status I/O pins of maximum 8 devices may be tied together for synchronizing purposes.
1998 Apr 07
Philips Semiconductors
Preliminary specication
TDA1562Q
on mute 0 HIGH
supply voltage
reference voltage
VRT 0 HIGH
MID LOW
1998 Apr 07
Philips Semiconductors
Preliminary specication
TDA1562Q
Just before the temperature protection becomes active the diagnostic output becomes continuously LOW. Load detection: directly after the circuit is switched from standby to mute or on, a build in detection circuit checks whether a load is present. The results of this check can be detected at the diagnostic output, by switching the mode select input in the mute mode. Since the diagnostic output is an open collector output, more devices can be tied together.
HIGH
handbook, full pagewidth
MID
LOW
HIGH
diagnostic output no load LOW t clipping signal short-circuit to supply or ground short-circuit across load
MGL265
1998 Apr 07
Philips Semiconductors
Preliminary specication
TDA1562Q
class-H
class-B
0 HIGH
diagnostic output
LOW
HIGH
MID
LOW 100
120
145
150 Tj (C)
160
MGL266
LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 134). SYMBOL VP PARAMETER supply voltage CONDITIONS operating non-operating load dump; tr > 2.5 ms; T = 50 ms IOSM Vsc Tstg Tamb Tj Ptot Note 1. Tj is a theoretical temperature which is based on a simplified representation of the thermal behaviour of the device. Tj = Tc + P Rth(j-c), where Rth(j-c) is a fixed value to be used for the calculation of Tj. The rating for Tj limits the allowable combinations of power dissipation P and case temperature Tc (in accordance with IEC 747-1). non-repetitive peak output current repetitive peak output current short-circuit safe voltage storage temperature ambient temperature junction temperature total power dissipation note 1 55 40 MIN. MAX. 18 30 45 10 8 18 +150 150 60 V V V A A V C C C W UNIT
1998 Apr 07
Philips Semiconductors
Preliminary specication
TDA1562Q
DC CHARACTERISTICS VP = 14.4 V; RL = 4 ; Tamb = 25 C; measurements in accordance with Fig.10; unless otherwise specied. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
Supplies VP1 and VP2 (pins 9 and 10) VP Vth+ Vth VPH1 Iq Istb VO VOO VOO VI II Vth1+ Vth1 VmsH1 Vth2+ Vth2 VmsH2 supply voltage supply threshold voltage supply threshold voltage hysteresis (Vth+ Vth) quiescent current standby current on and mute; RL = open circuit standby mute on on mute 8 7 14.4 200 110 1 18 9 150 50 100 30 V V V mV mA A
Amplier outputs OUT+ and OUT (pins 7 and 11) DC output voltage output offset voltage delta output offset voltage on and mute on and mute on mute 6.5 200 200 V mV mV
Mode select input MODE (pin 4) input voltage range input current threshold voltage threshold voltage hysteresis (Vth1+ Vth1) threshold voltage threshold voltage hysteresis (Vth2+ Vth2) mute on on mute VMODE = 14.4 V standby mute mute standby 0 1 3.3 Vp 20 2 4.2 V A V V mV V V mV
Status I/O STAT (pin 16) PIN STAT AS INPUT Vst IstH IstL Vth1+ Vth1 VstH1 Vth2+ Vth2 VstH2 1998 Apr 07 input voltage HIGH-level input current LOW-level input current threshold voltage threshold voltage hysteresis (Vth1+ Vth1) threshold voltage threshold voltage hysteresis (Vth2+ Vth1) 9 class B class H class H class B VSTAT = 14.4 V VSTAT = 0 V fast mute class B class B fast mute 0 1 3.3 200 200 VP 4 400 2 4.2 V mA A V V mV V V mV
Philips Semiconductors
Preliminary specication
TDA1562Q
UNIT
mA V A V A V C
VP 2.5
Diagnostic output DIAG (pin 8) output voltage load resistance for open load detection threshold junction temperature sensor active LOW 0.6 V C
1998 Apr 07
10
Philips Semiconductors
Preliminary specication
TDA1562Q
on-mode
on-mode
mute
Vms
class-H
class-B
Vst
1998 Apr 07
11
Philips Semiconductors
Preliminary specication
TDA1562Q
AC CHARACTERISTICS VP = 14.4; RL = 4 ; Rs = 0 ; f = 1 kHz; Tamb = 25 C; measurements in accordance with Fig.10; unless otherwise specied. SYMBOL Po PARAMETER output power CONDITIONS class-B; THD = 10% class-H; THD = 10% class-H; THD = 0.5% fro(h)(P) THD high frequency power roll-off total harmonic distortion Po (1 dB); THD = 0.5%; note 1 Po = 1 W Po = 20 W DDD active Gv fro(h)(G) Zi(dif) SVRR voltage gain high frequency gain roll-off differential input impedance supply voltage ripple rejection common mode rejection ratio input signal rejection ratio noise output voltage on and mute; note 3 standby; note 3 CMRR ISRR Vn(o) on; note 4 mute; note 5 on; note 6 mute; notes 6 and 7 Notes 1. The low frequency power roll-off is determined by the value of the electrolytic lift capacitors. 2. The low frequency gain roll-off is determined by the value of the input coupling capacitors. 3. Supply voltage ripple rejection is measured across RL; Vripple = Vripple max. = 2 VPP. 4. Common mode rejection ratio is measured across RL; Vcm = Vcm max. = 2 VPP. CMMR [dB] = differential gain (Gv) + common mode attenuation (Ac), (Test setup according Fig. 9; mismatch of input coupling capacitors excluded). 5. Input signal rejection ratio is measured across RL; Vi = Vi(max) = 2 VPP. ISSR [dB] = different gain (Gv) + mute attenuation (Am) 6. Noise output voltage is measured in a bandwidth of 20 Hz to 20 kHz. 7. Noise output voltage is independent of source impedance Rs. 70 80 Gv (1 dB); note 2 16 60 45 25 20 90 60 MIN. 20 70 55 20 0.03 0.06 10 26 150 70 90 80 90 100 60 TYP. 27 150 MAX. W W W kHz % % % dB kHz k dB dB dB dB V V UNIT
1998 Apr 07
12
Philips Semiconductors
Preliminary specication
TDA1562Q
+ VP 9 Ci supply 1 7 10
Ci VCM
TDA1562
2 14 SGND 17 PGND1 PGND2 6 12 11
RL
GND
MGL270
QUALITY SPECIFICATION Quality in accordance with SNW-FQ-611 part E, if this type is used as an audio amplifier.
1998 Apr 07
13
This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in _white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader. white to force landscape pages to be ... 1998 Apr 07
C1 3 CLASS-B CLASS-H FAST MUTE STANDBY MUTE ON status I/O 16 TEMPERATURE SENSOR mode select 4 disable LIFT-SUPPLY 100 nF 1 IN+ 1/2*Rs audio source 1/2*Rs 100 nF 2 IN 10 F 14 Vref 15 k 17 signal GND 15 C2
handbook, full pagewidth
Philips Semiconductors
100 nF VP2 10
2200 F
+ VP
CURRENT PROTECTION
TDA1562Q
LOAD DETECTOR
10 k 8 diagnostic 11 OUT
14
+ AMP.
disable
reference voltage
13 C2+ PGND1
12 PGND2
Preliminary specication
4700 F
TDA1562Q
GND
MGL271
Philips Semiconductors
Preliminary specication
TDA1562Q
SOT243-1
non-concave D x Dh
Eh
A2
B j E A
L3
Q c v M
1 Z e e1 bp w M
17 m e2
5 scale
10 mm
DIMENSIONS (mm are the original dimensions) UNIT mm Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT243-1 REFERENCES IEC JEDEC EIAJ EUROPEAN PROJECTION A 17.0 15.5 A2 4.6 4.2 bp 0.75 0.60 c 0.48 0.38 D (1) 24.0 23.6 d 20.0 19.6 Dh 10 E (1) 12.2 11.8 e 2.54 e1 e2 Eh 6 j 3.4 3.1 L 12.4 11.0 L3 2.4 1.6 m 4.3 Q 2.1 1.8 v 0.8 w 0.4 x 0.03 Z (1) 2.00 1.45
1.27 5.08
1998 Apr 07
15
Philips Semiconductors
Preliminary specication
TDA1562Q
The device may be mounted up to the seating plane, but the temperature of the plastic body must not exceed the specified maximum storage temperature (Tstg max). If the printed-circuit board has been pre-heated, forced cooling may be necessary immediately after soldering to keep the temperature within the permissible limit. Repairing soldered joints Apply a low voltage soldering iron (less than 24 V) to the lead(s) of the package, below the seating plane or not more than 2 mm above it. If the temperature of the soldering iron bit is less than 300 C it may remain in contact for up to 10 seconds. If the bit temperature is between 300 and 400 C, contact may be up to 5 seconds.
This data sheet contains target or goal specications for product development. This data sheet contains preliminary data; supplementary data may be published later. This data sheet contains nal product specications.
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specication is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specication. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale.
1998 Apr 07
16
Philips Semiconductors
Preliminary specication
TDA1562Q
1998 Apr 07
17
Philips Semiconductors
Preliminary specication
TDA1562Q
1998 Apr 07
18
Philips Semiconductors
Preliminary specication
TDA1562Q
1998 Apr 07
19
For all other countries apply to: Philips Semiconductors, International Marketing & Sales Communications, Building BE-p, P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax. +31 40 27 24825 Philips Electronics N.V. 1998
SCA59
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights.
545102/1200/01/pp20
This datasheet has been download from: www.datasheetcatalog.com Datasheets for electronics components.