Professional Documents
Culture Documents
Sl1200mk2 Service Man
Sl1200mk2 Service Man
experienced repair technicians This service literature is designed for public . It does not and is not designed for use by the general only of cau:'.ons to advise non-technical individuals contain warnings or a product. Products powered potential dangers in attempting to service repaired only by experienced by electricity should be serviced or attempt to service or repair the product professional technicians. C.iy t;+ anyone else could or, ,products dealt with in this service literature injury or death . rest'' in.. serious
ORDER NO . SD7908-1601
Turntable System
" The model SL-11 200MK2 (M) is available in U .S .A . only . *The model SL-1200MK2 (MC) is available in Canada only .
SPECIFICATIONS
Power supply : Power consumption : Dimensions : (WxHxD) Weight :
Specifications subject to change without notice . Weight and dimensions shown are approximate . 120 V,AC,50or60Hz 12W 45 .3x 16 .2 x36 cm (17-27/32"x6-19/64"x l 4-11/64") 11 kg (24 .3 lb) Quartz direct drive Manual turntable Direct drive Brushless DC motor Aluminum diecast Diameter 33 .2 cm (13-5/64") Weight 2 kg (4 .4 lb .) 33-1/3 rpm and 45 rpm All quartz-locked 8% range 1 .5 kg-cm (1 .3 Ib-in) 0 .7 s . from standstill to 33-1/3 rpm Electronic brake Rumble : -56 dB (I EC 98A Unweighted) -78 dB (IEC 98A Weighted) Universal 230mm (9-1/16") 31 .8-37 .8 mm (helicoid part 6 mm) (1-21 /32"-3-35/64") (helicoid part 15/64") 15 mm (19/32") 12 g (without cartridge) 22 Less than 7 mg (lateral, vertical) Within 2 32' (at the outer groove of 30 cm (12") record Within 0 32' (at the inner groove of 30 cm (12") record 0-2 .5 g 6-10 g 13 .5-17 .5 g (including headshell) 9 .5-13 g 17-20 .5 g (including headshell) 3 .5-6 .5 g 11-14 g (including headshell) 7 .5 g
General
Turntable section
Type : Drive method : Motor : Turntable platter: Turntable speeds : Pitch control : ;:carting torque : Build-up characteristics : Braking system : Speed change due to load torque : Wow and flutter :
Type : Effective length : Arm height adjustment range : Overhang : Effective mass : Offset angle : Friction : Tracking error angle :
Tonearm section
0% within 1 .0 kg-cm (0 .87 Ib-in) 0 .01% WRMS* 0 .025% WRMS (JIS C5521) 0 .035% peak (IEC 98A Weighted) * This rating refers to turntable assembly alone, excluding effects of record, cartridge or tonarm, but including platter . Measured by obtaining signal from built-in frequency generator of motor assembly .
Stylus pressure adjustment range : Applicable cartridge weight range : (with auxiliary weight) : (with shell weight) : Headshell weight :
Cud Matsushita Electric Industrial Co . Ltd. All rights reserved . Unauthenzed copying and distribution is a violation of law Matsushita Electric of Canada Ltd . 5770 Ambler Drive, Mississauga, Ontario LAW 2T3
Panasonic Company Panasonic Hawaii, Inc . Division of Matsushita Electric 320 Waiakamilo Road, Honolulu, Corporation of America .Hawaii 96817 One Panasonic Way, Secaucus, New Jersey 07094
SL-1200MK2 CONTENTS
DISASSEMBLY PROCEDURE . . . . . . . . . PARTS IDENTIFICATIONS . . . . . . . . . . . ARM BASE ASSEMBLING PROCEDURE. FEATURES . . . . . . . . . . . . . . . . . . . . . . . . ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . SCHEMATIC DIAGRAM . . . . . . . . . REPLACEMENT PARTS LIST (Electrical) .. . TROUBLE SHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. .. .. .. . .. .. .. .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2,3 . 3 . 4 . 5 . 6 . 7,8 . 9 . 10 PRINTED CIRCUIT BOARD . . . . . . . . . . . . . . . . . . . . . ADJUSTMENT (Electrical) . . . . . . . . . . . . . . . . . . . . . . . REFERENCE VOLTAGE AND WAVEFORM AT EACH PIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BLOCK DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EXPLODED VIEWS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . REPLACEMENT PARTS LIST (Mechanical) . . . . . . . . . . EXPLODED VIEWS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . IC .. . .. . .. . .. . .. . 11,12 13 13,14 15,16 17,18 19 20
DISASSEMBLY PROCEDURE
How to remove panel cover 1 . Remove head shell and turntable. 2 . Secure arm with arm clamp . 3 . Remove 5 screws O of the panel cover as shown in Fig. 1 . How to remove stater frame coil and F.G detector coil 4 . Remove 3 connectors O and 2 read wires @ from power transformer as shown in Fig. 2. 5 . Remove 3 screws @ of the drive circuit board and 3 screws of the stater frame cover as shown in Fig. 2. 6 . Disconnect 18 soldered parts O of the stater coil and 4 soldered parts O of the F.G detector coil as show in Fig. 3. 7 . Remove 3 screws Q of the stater frame ass'y as shown in Fig. 3. How to remove bottom base ass'y 8. Remove 4 audio insulators . (Counterclockwise rotation) 9. Remove 17 screws and spacer Q as show in Fig. 4. 10 . Remove 11 screws O as shown in Fig. 4. How to remove stylus-illuminator lamp 11 . Remove 2 screws Q of the stylus-illuminator lamp ass'y as shown in Fig . 5. 12 . Remove 1 screw O as shown in Fig. 6. How to remove neon-illuminator L .E .D . 13 . Remov e 4 screws Q as shown in Fig. 5. 14 . Remove 1 circlip Q and switch cam QQ as shown in Fig. 5. 15 . Remove strobo-illuminator case . How to remove tone arm 16 . Remove 4 screws Q of the arm base cover as shown in Fig . 5. 17 . Remove 2 screws of the phono cord clamper as shown in Fig. 5 . 18 . Remove phono cord clamper as shown in Fig. 7. 19 . Remove 2 screws Q of the phono cord p.c .b . as shown in Fig . 8. 20 . Remove 2 screws as shown in Fig . 8. 21 . Remove 2 screws Q of the silicon oil dumper as shown in Fig. 8 . 22 . Remove 3 screws Q as shown in Fig. 8 . 23 . Remove 2 screws 0 of the tone arm as shown in Fig. 9.
Lamp caset
Fig .
Fig . 9
m PARTS IDENTIFICATION
Hinge
Balance weight
Fig . 10
10
3 . Hold the arm base and set the red line mark on the arm base to the scale near "2", then turn the arm base clockwise . (See Fig . 12) Note : Take care not to allow deflection of the predetermined positions of the control ring and arm base seat .
SL-1200MK2
Total quartz locked continuous pitch adjustment f8% Quartz-phase-locked control means almost perfect accuracy of turntable rotation . But with most quartz turntables, this accurate control circuit must be cut out when the pitch control is employed . With the SL-1200MK2, however, pitch is variable continuously (analogically) by up to 8% under total quartzlocked control . The pitch is controlled with a large sliding lever, located to the right of the turntable platter . Four lines of platter markings are also provided indicating +6%, +3 .3%, 0% (exact rated speed) and -3 .3% change from rated speed . Aluminum diecast cabinet and special heavy rubber base material provide acoustic isolation The effects of external vibrations are dramatically reduced in the turntable by this new turntable construction . The turntable base is precision-made aluminum diecast. And the underside of the main base is made of a heavy rubber material (special one-piece molding) which has excellent vibration resistance and absorbing characteristics . The turntable platter is also vibration-damped with specially fabricat rubber matting in the underside along with the thick turntable sheet (rubber mat) . Four large-size insulating feet also help to absorb unwanted vibrations . These features make SL-11 200MK2 ideal for use with extrahigh sound pressure levels . High torque for fast starts The integral rotor/platter motor delivers 1 .5kg-cm (1 .3lb-in) starting torque . This high torque gives very quick starts enabling the platter to reach 33-1/3 rpm within 0 .7 s. (a quarter of a turn) . This is a big advantage in many professional applications where fast cueing is a necessity. Stylus illuminator for low-light conditions You'll appreciate the stylus illuminator when you are using the turntable under low-light conditions . The illuminator can be hidden in the turntable base, should you need it, simply push a button and it will pop up gently and cast a beam of light across the disc in the area traversed by the tonearm .
FEATURES
You can then clearly see the spaces between the selections on the record, and cue the arm exactly where you want it . The illuminator can then be pushed back down into the base . High sensitivity, low mass, gimbal suspension tonearm The highly sensitive tonearm features a genuine gimbal suspension, the rotational center of which is precisely defined at one point. Bearings are finished to a tolerance of 0 .5 microns. This and the extra-closeness of pivot center to the bearings, result in the minimal friction of 7 mg (0 .007 g) for both horizontal and vertical movement . Add to this the low 12-gram effective tonearm mass (including headshell, without cartridge) and you have a tonearm compatible with the wide range of compliances found in today's cartridges . If you choose a popular high compliance MM cartridge, the low range resonance frequency will appear in the correct area to avoid warp frequencies of records, but without entering the low end of the audio spectrum . This tonearm is provided with a computer designed, light-weight, high-rigidity headshell made of single-piece diecast aluminum to resist partial vibration. The universal design allows headshell interchangeability . Contacts are gold-plated . Helicoid tonearm height adjustment Arm height is adjustable within a range of 6 mm to accommodate varying cartridge dimensions . Adjustments are done with a precision-made helicoid . Other fine features " Quick stops are achieved with a fully electronic braking system . " A strobe illuminator is provided . The stroboscope is controlled by the extremely stable quartz oscillator, rather than potentially unstable AC line frequency. Power on/off control built-into strobe illuminator for ease-of-operation . Soft-touch start-stop switch allowing precision control capability without the annoyance of accidental operation. " Technics integral rotor/platter motor construction with full cycle detection FG .
)MK2
lections want it . nto the
SL-1200MK2
Pitch control (fine adjustment of speed) (See Figs . 18 and 19 .) When the pitch control knob is located at the center of the position after turning on the power, the green LED indicator is lit showing the operating condition for the predetermined speed (either 33-1/3 or 45 rpm) . The pitch control is variable in a range of 0-8% . Adjustment should be done on the basis of indicator scale . Figures on the indicator show approximate percentages for variable pitch control . When the strobe dots in 4 stages marked at the peripheral edge of the turntable appear to be stationary, variation of individual pitches is shown . (See Fig . 19 .) Note : The strobe-illumination of this unit employs a strobe-illuminator LED synchronized with the precise quartz frequency . For fine adjustment of the turntable speed, be sure to effect the adjustment according to the LED illumination . The LED illumination is not synchronized with fluorescent lamps . Adjustment of arm-lift height (See Figs . 20 and 21 .) The arm-lift height (distance between the stylus tip and record surface when cueing lever is raised) has been adjusted at the factory before shipping to approximately 8-13mm . If the clearance becomes too narrow or too wide, turn the adjustment screw clockwise or counterclockwise, while pushing the arm lift down . Clockwise rotation -distance between the record and stylus tip is decreased . Counterclockwise rotation -distance between the record and stylus tip is increased . Note : As the adjusting screw has hexagonal head, be sure to make the adjustment while depressing the arm lift, or the screw will not move freely . Also be sure that the hexagonal head retracts correctly into the arm lift when the latter is released .
ADJUSTMENTS
Adjustment of the tonearm height (See Fig . 22 .) The height of the tonearm can be adjusted up to 6 mm, and a scale is provided on the adjust ring in 0 .5 mm increments . Be sure to set the proper arm height using the adjust ring scale and referring to the table . Height of cartridge (mm) (H) 15 16 17 18 19 20 21 Scale reading on the arm-height adjust ring 0 1 2 3 4 5
~ension gimbal recisely - ance of t center f7 mg nt . Add icluding m comtoday's ice MM )pear in As, but m . This weight, iminum vs head-
For example, if the cartridge height is 17 .5 mm, the armheight adjust ring should be positioned at the intermediate location between 2 and 3 on the scale . (See Fig . 22 .) Caution : Be sure to lock the tonearm by turning the arm lock knob in the direction indicated by the arrow after finishing the height adjustment for the tonearm . Lubrication (See Fig . 23 .) Apply 2 or 3 drops of oil once after every 2000 hours'of operation . The time interval is much longer than that for conventional type motors (200-500 hours) . Please purchase original oil . (Part number is SFWO 010 .)
accomre done
(t)
: ig . 17
appears stahonary at the pitch (2) appears stahonary at the pitch slat, onary at the pitch f3f appears (4) appears stahonary at the pitch
o3 3%
Fig . 19
Schematic Diagram
2 A
6
SVDSl RBA20
7
Q
~pnai
ORG T .I
J
Q3
R5 4
AC 117V (50/60Hz)
BLU }
TP4
SVORD5.1E
'
D2
R204
2.
Braking
adjustment
TP21 R205
VR201 R215 4 .7K R214 22K IC201 50KB TP22
A N 6680
TF Q202
G
VR303
MA150
D204
5203 S/S
5201 33
1 5202
45
SVDSR105C
D201, 202
STR(
THE SHADED AREA ON THIS SCHEMATIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR SAFETY . WHEN SERVICING IT IS ESSENTIAL THAT ONLY MANUFACTURER SPECIFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SHADED AREAS OF THE SCHEMATIC.
fP3
220 P19
OVI
.213 Ilop i
D206 5401
WITCH
STYLUS-ILLUMINATOR STROBE ILLUMINATOR NOTO : 1 . S201 : Speed selector switch (33-1/3 r.p .m .) in "ON" position . (push condition) 2 . S202 : Speed selector switch (45 r .p .m .) in "OFF" position . (not-push condition) 3 . S203 : Start/Stop switch in "OFF" position . (notpush condition) 4 . S301 : Pitch lock switch in "ON" position . (center position) 5 . S401 : Stylus-illuminator switch in "OFF" position . 6 . S601 : Power switch in "ON" position . 7 . The drive circuit IC voltage and wave form are not indicated in side the schematic diagram . 8 . Indicated voltage values are the standard values for the unit measured by DC electronic circuit tester (high impedance) with the chassis taken as standard . Therefore, there may exist some errors in the voltage values, depending on the internal impedance of the DC circuit tester .
D204
D205
PLl
Part numbers are indicated on most mechanical parts. Please use this part number for parts orders. indicates that only parts specified by manufacturer be used for safety . SL-1200MK2(M) + [MI , SL-1200MK2 (MC)+ (MC1 Part No . Part Name & Description Ref, No. 8108 8109, 110 R201 R202 8203 R204 8205 R206 8207 R208 R209 R210 R211 R212 R213 8214 R215 R216 8217 R218 R219 R220 R221 8301 R302 R303 R304 R306 R601 CAPACITORS Cl C2 C3 C101, 102 C103 C104,105 C106,107 C108 C109, 110 C111 0112 C201 C202,203 C204 C205 C206 C207 C208 C209 C210 C211 C212 C213 C214 C215 C216 C301,302 C303 C304 C305 C306 C601 [MI C601 [MCI ECEBlHS471 ECEAIVS330 ECEAIES220 ECEAlVS330 ECEAlVS330 ECQMlH104KZ ECQMlHl04KZ ECEAlES101 ECQMIH104KZ ECQMlH562KZ ECEAIJS4R7 ECEAICS330 ECEA50ZI ECQMlH473KZ ECEA1AS221 ECEA50ZI ECCDIHt01K ECCDlH390K ECEAIES101 ECQMlH224KZ ECQMlH473KZ ECEA50Z3R3 ECCDlH47lK ECEAIES101 ECEA50Z1 ECEAIES470 ECQK1123FZ ECEA50ZI ECEA1HS100 ECQMlHl22KZ ECEA50Z1 ECQFlA473MD ECQUIA473ME Electrolytic, Electrolytic, Electrolytic, Electrolytic, Electrolytic, Polyester, Polyester, Electrolytic, Polyester, Polyester, Electrolytic, Electrolytic, Electrolytic, Polyester, Electrolytic, Electrolytic, Ceramic, Ceramic, Electrolytic, Polyester, Polyester, Electrolytic, Ceramic, Electrolytic, Electrolytic, Electrolytic, Polyester, -Electrolytic ;`' ElectrOiytic, Polyest& ; " Electrolytic, Polyester, Polyester, 470yF, 33juF, 22/AF, 33juF, 33pF, 0 .1PF, 0 .1,uF, 100UF, 0,1yF, 0 .0056pF, 4,7pF, 33pF, luF, 0 .047liF, 220pF, luF, 100pF, 39pF, 100pF, 0.22pF, 0.047pF, 3.3pF, 470pF, 100pF, 1uF, 50V 35V 25V 35V 35V 50V, 50V, 25V 50V, 50V, 63V 16V 50V 50V, 1ov 50V 50V, 50V, 16V 50V, 50V, 50V 50V, 25V 50V A Part No . ERD25FJ103 ERXIANJ4R7 ERGlANJ561 EAD25FJ103 ERD25FJ470 ERD25FJ272 ERD25TJ124 ERD25TJ"183 ERD25TJ563 ERD25TJ224 ER025TJ154 ERD25TJ183 ERD25FJ103 ERD25FJ121 ERD25FJ122 ERD25TJ223 ERD25FJ472 ERD25TJ154 ERD25TJ223 ERD25FJ102 ERD25FJ332 ERD25FJ221 ERD25FJ471 ER025CKF3301 ERD25FJ471 ERD25FJ822 ERD25FJ152 ERD25TJ223 ERD25FJ4R7 Part Name & Description Carbon, Metal Film, Metal Oxide, Carbon, Carbon, Carbon, Carbon, Carbon, Carbon, Carbon, Carbon, Carbon, Carbon, Carbon, Carbon, Carbon, Carbon, Carbon, Carbon, Carbon, Carbon, Carbon, Carbon, Metal Film, Carbon, Carbon, Carbon, Carbon, Carbon, 10kn, 4 .7fl, 560fl, 1Okfl, 47fl, 2 .7kfl, 120kfl, 18kf1, 56kfl, 220k fl, 150kfl, 18kf2, 1OkQ, 120fl, 1 .2kfl, 22kfl, 4 .7kfl, 150kfl, 22kf1, lkfl, 3 .3kf2, 22012, 47012, 3.3kfl, 470(2, 8.2kf2, 1 .5kfl, 22kfl, 4 .7(2, 1/4W, 1W, 1W, 1/4W, 1/4W, 1/4W, 1/4W, 1/4W, 1/4W, 1/4W, 1/4W, 1/4W, 1/4W, 1/4W, 1/4W, 1/4W, 1/4W, 1/4W, 1/4W, 1/4W, 1/4W, 1/4W, 1/4W, 1/4W, 1/4W, 1/4W, 1/4W, 1/4W, 1/4W, t t t t t t t t t t t t t t t t t t t t t t t t t t t t t 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 1% 5% 5% 5% 5% 5%
INTEGRATED CIRCUITS IC101 IC201 IC301 IC302 TRANSISTORS Q1 Q2, 3, 202 Q201 Q203 DIODES D1 D2,301 D204 D201, 202 D203-206 D401 CRYSTAL X201 SVQU306115 Crystal, 4 .19328MHz Oscillator A SVDSIRBA40 MA7051 MA162A SVDSR-105C SVDEBR5505S SVDGL-9PG2 Rectifier Diode,Zener5 .iV Diode Light Emitting Diode Light Emitting Diode Light Emitting Diode 2SD389A-Q 2SD637 2SC1846-R 2SC1328-T Transistor Transistor Transistor Transistor AN6675 AN6680 AN6682 SVITC4011BP Integrated Integrated Integrated Integrated Circuit Circuit Circuit Circuit
VARIABLE RESISTORS VR201 VR301 VR302 VR303 SWITCHES S201 5202 S203 5401 S601 LAMP PL1 TRANSFORMER Tl FUSE F1 RESISTORS R1 R2 R3 R4 R5 R101 R102 R103 R104 R105 R106 R107 ERD25FJ562 ERD25FJ682 ERD25FJ272 ERD25FJ561 ERD25FJ471 ERD25FJ103 ERXIANJ4R7 ERD25FJ472 ERD25TJ473 ER026FJ403 ERD25FJISO ERXIANJlR5 Carbon, Carbon, Carbon, Carbon, Carbon, Carbon, Metal Film, Carbon, Carbon, Carbon, Carbon, Metal Film, 6 .6k fl, 6 .8kfl, 2 .7kfl, 560fl, 470fl, 10kfl, 4 .7fl, 4 .7kfl, 47kQ, 10kfl, 1511, 1 .511, 1/4W, 1/4W, 1/4W, 1/4W, 1/4W, 1/4W, 1W, 1/4W, 1/4W, 1/4W, 1/4W, 1W, t t t t t t t t t t t t 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% XBA2FO3NU100 Fuse, 350mA ~SLT60EL)713 Power Transformer SFDN122-01 Lamp, Stylus-illuminator EVQP5RO4K EVQP5RO4K SFDSSS5GLl3C SFDSD2MSL-4 SFDSSS5GL-2 Switch, Switch, Switch, Switch, Switch, Speed Selector (33-1/3r .p.m .) Speed Selector (45r .p .m .) Start/Stop Stylus-illuminator Power EVLS6AA00a54 EVMH2GAOOB53 EVLS6AAOOB54 EVBJ05Cl9ABE Braking Adjustment (BRAKE), 50k(1 (B) Adjustment of Pitch Control f0%(PITCH), 5kn (B) Pitch,Adjustlnent (Gain) 50kfl Pitch Control Volume
47uF, 25V 0.012pF, 125V, I#F, 50V 10pF, 50V 0.0012pF, 50V, 1pF, 50V 0.047pF, 400V, 0.047pF, 400V,
AN6682
SVITC4011BP
2SC1846
2SC1328
2SD637
2SD389
r 13
F 1: BC
TROUBLE SHOOTING
Power switch doesn't operate Power circuity check " TP5 - 20V NO F1, S601, T1 D1, 61.1 -Q3
(B)
Reference voltage circuity check " TP5-20V YES Control circuity check " Check voltage and wave form at IC201
NO
NO
IC201 X201
Drive circuity check " Check voltage and wave form at IC101 YES heck voltage on Q201 " Base voltage - 10V NO Q201
Runaway operation
Reference voltage circuity check " TP5- 20V YES Control circuity check " Check voltage and wave form at IC201
NO
Q1 -Q3 D2
NO
IC201
Drive circuity check " Check voltage and wave form at IC101 YES FG circuity check " Check voltage on Q203
NO
NO
Q203, FG coil
Control circuity check " Check voltage and wave form at I C201
NO
X201 I C201
Pitch control circuity check Check voltage and wave form at IC301, IC302
NO
IC301 IC302
NO
(F)
Check voltage at TP28 and TP29 " TP28 - 18AV " TP29 - 9.6V
NO
r r
02
S20f
133
START/STOP SWITCH
D204
D203
POWER TRANSFORMER
G
AC 117V (50/60 Hz)
BLU
H
ORG BLU
BRN
RED
5401
STYLUS-ILLUMINATOR SWITCH
BLK NL1 IC302 BLK R401 1 .5K IC301
RED ORG
ORG
BRN
AN6682
YEL
SVITC4011 BP
r
- 470 E
zv
2S D389
Q1
2SC1328
73 . . -8 .2K
r~
Q203
1+
16VID0
R21J t~
fi, k
7P74 BRN RED ORG YEL R221 470 "---Mh-.-" R 219 :: R216 C202 50'11 R211 10K TP23 TP C21 3.3 150F . iH. FT
10 s
__" PSi4T'~ A k
1
C20
gar
C109 G -if-R10 .1 1
R101
Rt
5-of
405 ll!t
0163
6 8212 '20
nC C106 01 ~ RI :In }1. rc, -At~
BLU
S601
POWER SWITCH
AN6680
Q262
1601
_ BLU B LU
A N 6675
IC101
2S D637
Q2, 3
2SD637
SL-1200MK2 SL-12
ADJUSTMENT (Electrical)
Adjustments (Electrical) Notes: 9 Make the following adjustments Condition of the set . 1 . Power switch . . . . . . . . . . . . 2. Pitch control . . . . . . . . . . . . 3. Speed selector switch . . . . . . Instruments to be used 1 . Tester 2. Frequency counter Adjustment Adjustment of pitch control t0% (PITCH) Adjustment of pitch control gain Braking adjustment (BRAKE) after replacing parts such as IC's, transistors, diodes, etc. . ON . Center position . 33-1/3 r.p .m .
(D
Connection Points Frequency counter (2) -. TP27 0 - GROUND Tester TP31 and TP32 -
Adjustment Method 1 . Pitch control switch to center position . 2. Adjust VR301 for 262.08 kHz 10 .05 kHz of frequency. Adjust VR302 for 2.7 k92 t0.1 of resistance value Adjust VR201 for complete stop within 120 - 270 after stop signal initiated . (Turntable becomes free a few seconds after stop)
STOP SIGNAL O
VR302
OO
VR201
2700
Turntable &1 0
Start =
Stop 15V
Stop
2V sv
0v sV
oV
,uV
O Os OO 08
5V ( 'S 5V
6 .6V ov 5V 15v
sV q sv 0 S
-0 0 ' ,.,_
15V
15V
~ 15V
209. ,
(S , f
15V
20V
*40"1
r
15V
15V
ov
15V
ov
15V
Stop 2 .5V
41.
Start
1)
Stop . Ov 9 .8V L I M Q OO t I
stop -:
OV 9 .8V
fl fl u u w
A
tov
-
iov
,3J
o 9v
Same as at right
.4 ,qY
6v
Ov T
,
Same as at right
v.xw
7
~oxw
x.sv
0 .2V
~~
IV 2 .8V
T5
-[A-,-!V 3 .4V OV
2.5V
T7
sv
S .SV
8v
Stop
sv T
Stop
Start
Stop
-v
Same as at right
J U LJ L
lhf Ov w
Same as at right
'v
TO
,.,
TB
Same as at right 9V
T'
3 .9V,(A
9v
Same as at right
x.sv
~IC302 (SV ITC4011 BP) Start T1 Same as at right 5V Ts Same as at right SV T4A Stop 41 ~~ 5V -~ Sv 5V
Start
T5
Stop y, O
Start
Stop
Same as at right 5V
OO
OV Same as at right
5V , OV I~t'~ Sv
, t . SV
BLOCK DIAGRAM
0 U
(33 r .p .m. indicator) (45 r .p .m . indicator) (33 r .p .m. switch) (45 r .p .m . switch) (Start/Stop switch)
01-2 .3
D1
0203
~ ca f E ~E 0 c cli 1
CD
C.R OSC
P.C
C .P
PF
u u
ci
_ 2 0 3
vCC 9 { !
~7
,n 0 M
v
S301 VR303
16
~C " tV h 1~
SrtUU'a
SL-12C
REPLACEMENT Notes : 1.
PARTS
LIST (Mechanical)
Part numbers are indicated on most mechanical parts . Please use this part number for parts orders . 2 . indicates that only parts specified by manufacturer be used for safety . 3 . SL-1200MK2(M) +(MI,SL-120wIK2(MC) +[MC1 Part No . Part Name & Description Dust Cover Turntable Mat Turntable Cover, Turntable Cover, Stater Frame Ass'y Stater rame FG Detector Coil Ass'y Shaft, Stater Frame Ass'y Plate, Shield Cabinet Ornament, Stylus-illuminator Knob, Power Switch Case, Strobe-illuminator Knob, Start/Stop Switch Spring, Start/S1op Knob Base, Operation Knob, Speed Selector (33-1/3r .p .m .) Connector, 7-PIN Spacer, Rubber (Speed Selector) Ball, Switch Cam Spring, Switch Cam Cam, Switch Spacer, LED Cover, Lamp Boss, Drive Spring, Drive Boss Pin, Lock Canceler Bracket, Stylus-illuminator Plate, .Lock Operation Connector, 3-PIN Pin, Guide Spring, Lock Canceler Pin Spring, Lock Operating Plate M'tg Pin, Lock Operating Plate M'tg Clamper; AC Cord Bracket, AC Cord AC Cord Bracket, Power Transformer Cushion, Power Transformer Spacer, Power Transformer Knob, Pitch Control Volume Ornament, Pitch Control Volume Shading Cloth, Pitch Control Volume Hqlder, LED - Bucket, Pitch Control Volume Connector, 4-PIN Supporter, Bottom Base Base, Bottom Supporter (A), Hinge Supporter (B), Hinge Case, Hinge Audio Insulator Supporter (C), Hinge Knob, Speed Selector (45 r.p .m) Name Plate Name Plate Pipe (A) Pipe (B) Hinge Ass'y Ref . No . 75 [M] 75 (MC) 76 77 78 79 80 81 Part No . SFDH360MOl SFDH028-01 SFP 1 720 SFPKDKD1720 SFPKB 1 7201S SF P 12201 SFPAB 17206 Part Name & Description Phono Cord Phono Cord GroundWire Arm Rest Arm Base Ring, Arm Base Operation ng, Bracket, Arm Base Knob, Anti-skate Force Control
Ref . No .
CABINET and CHASSIS PARTS 1 2 3 4 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25__ 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 IM] 65 [MCI 56 57 58 SFAD122-01A SFTG172-01 SFTE172-01Z SFUM172-05 SFMGQ20401 SFMG520-31A SFMZ172-01E SFMZQ20-01A SFUP122-12 SFAC122-01 SFUM172-04 SFKT122-01 SFKK122-01E SFKTO15-06 SFQA122-01 SFUM122-01 SF KTbtS-01E SF DJ I22,02E SFGZ122-01 SFYB5-32 SFQA520-01 SFUM122-03 SFUM015-11 SF KK172-01 SFXB122-02 SFQA172-01 SFXJ172-01 SFUP122-02E SFUP122-03 SFDJ122-03E SFX0172-01 SFQA520-01 SFQA001-02 SFXJ172-05 SFHKO40L SFUP025-01 RJASVA SFUP132-03 SFGC122-01 SFUP122-10 SF KT122-02 SFKK122-03 SFUZ122-01 SFUP122-01 SFDJ122-01E SFUP122-13 SFAU122-01 SFUP122-05 SFUP122-04 SFUM170-07 SFGC122-02E SFUP122-06 SFKTO15-02E SFNN122M01 SFNN122COI SFX0122-01 SFX0122-02 SFAT122-01A
"
'
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 ACCESSORIES A1 [MI A1 [MCI A2 A3 A4 A5 A6 A7 A8 PACKINGS P1 [M] P1 [MCI P2 P3 P4 P5 P6 P7 P8
XTN3+88FZ -FXGQ20-02 XTN3+88 XTN26+88 XTN4+10B XWA48 XUC3FT XUC2FT XUC25FT SFXW910J02 XTN3+408FZ XSN3+10BVS XWE3F12FZ XTN3+25BFZ SFXW122-01 XWE3E10 SFPEW1100 SFPEW11003 XSN3+BS SFXG132-01 XTV3+BBFN XTN3+108 XTN2+108 XSN17+3FY XSN3+149 SFXW172-04 XUB14FT SFUZ172-05 XTN3+6B XSN3+8S XWA3BFZ XWA38 XWG3 SFXG829-1 XUCSFT XTW3+SB XTV3+88FN XWE4A10EW XTN3+258 XYN3+C6FZS XSN3+128VS SFPEW17201 XWG26
Screw Screw Screw Screw Screw Washer Circlip Circlip Circlip Washer Screw Screw Washer Screw Washer Washer Washer Washer Screw Screw Screw Screw Screw Screw Screw Washer Circlip O Ring Screw Screw Washer Washer Washer Screw Circlip Screw Screw Washer Screw Screw Screw Washer Washer
61 62 63 64 65 66 67 68 70 71 72 73 74
TONE ARM and ARM BASE SFPCC31001 K SFPAM18201 K SFPWG17201K SFPRT18201K SFPZB17202 SFQA829-03 SFPAB13202 SFPJL18202K SFPZB12203 SFUM170-06 SFPZB12204 SFPAB18201 K SFPZB12201 K
Head Shell Tone Arm Ass'y Balance Weight Ass'y Lift Assy Knob, Arm Base Lock Spring, Lift Ass'y Knob, Arm Lift Oil Damper Plate, Arm Base Cover Spacer, Phono Cord Clamper, Phono Cord Tone Arm Fixing Plate Ass'y Plate, Position Fix
Instruction Book Instruction Book Adaptor, 45 r .p.m . Nut, Cartridge Washer, Cartridge Screw, Cartridge Screw, Cartridge Overhang Gauge Shell Weight
Carton Carton Pad, Front Pad, Rear Pad, Top Pad, (A), Turntable Pad, (B), Turntable Polyethylene Cover, Turntable Unit and Dust Cover Polyehtylene Cover, Turntable
EXPLODED VIEWS
20
Printed in Japan