You are on page 1of 14

I have received many questions regarding the lockets I made inspired by the movie "The Illusionist".

Here is a video of the completed model. (6.7 mb) And here (finally) are some drawings and instructions for what I did: 1. Go to hobby/craft store and buy: (unless you like cutting shapes) 3 wooden heart wafers (or package with at least 3 wafers) Pack of axel pegs*

*Axel pegs should be in the size you want. The width of the axel will affect the size of some of the notches you must make in the wafers.

2.

Axel Pegs

3. Cutting the lid-rotation pin (half-pins): Work on the top/rounded part of the peg first so you'll have the leverage of the whole axel to hold onto. Shape the top of the peg as illustrated. Note: the top of the pin should be made concave: refer to step 5 for more info. Cut the excess from the axel. Save the excess: You can use it to make the center pin later. The bottom of the pin is cut into trapezoidal shapes (see step 4). The middle section should remain round. Cut the pin in two halves. This pin is designed to glue to the lid wafers and rotate when the two halves come together to make the heart-shape.

4. Cut the hearts in half. There are three layers of heart: lid (top), middle, and bottom. Lid (Top) Wafers: On the lid wafers, make trapezoidal notches for the half-pins. The half-pins will later glue to these notches.

5. Back/Bottom Wafers: The back/bottom wafers will have circular/convex notches to receive the rotating head of the lid-rotating pin (half-pins). Note: the concave/convex nature of the pin and notch. This is to prevent the lid pieces from falling out when the locket is rotated between the heart and oval forms. Cut these notches as smooth as possible: the lid will rotate by turning the pin in this socket.

6. Middle Wafer: Notches for Lid-rotating pin: Cut notches for the lid-rotating pin. The middle and bottom wafers will sandwich the head of the lid-rotating pin. The notch should be cut to match the width of the circular mid-section of the lid-rotating pin. Make these as smooth as possible. Notches for center pin: Measure to the midpoint (axis) where the locket will turn to rotate between the oval and heart shapes. The center-peg must be in the center of the middle wafer - long ways. I used a tiny drill bit and an exacto knife to cut these notches. Cut one side square, and the other in a 'match head' shape. See next step to match these notches to the shape of the center-pin.

7. Center Pin: Using either the excess peg saved earlier or some other wood, cut the center pin: One side square and one side in a "match head" shape. Cut as cleanly as possible to match the notches in the middle wafer.

8. A "glue side" is where the pieces are glued together - I decided that was easier than trying to call them top/bottom/bottom/top, etc. Remember to only use a thin layer of good wood glue. Don't let the glue seep into either of the pin sockets or the pieces won't rotate and the pins could snap. (This happened several times with me.) First glue the half-pins to the lid wafers. (Diagram Step #1) Next Glue the square end of the center-pin to the square notch of the middle wafer. (Diagram Step #2) Allow both to dry.

This is how the wafers stack before gluing. 9. Place the 'match head' of the center-pin into the notch of the middle wafer. Check the fit of the pin and notch. When set, there should be enough friction to keep the halves from spinning. Adjust if needed. When gluing the center pin, it is easier to remove the lid pieces and deal only with the middle and bottom wafers. Carefully glue the bottom wafers to the middle wafers to secure the center-pin. Use clamps to hold the wafers tightly in place. Allow a few days to dry.

10. And if that wasn't hard enough to understand... Here's the part that's hard to describe: Insert the lid pieces: Turn the locket half-way between the heart and oval forms. (Perpendicular). The convex notches for the lid-rotation pin should now be visible. Carefully rotate the pin-head into the notches. Don't force them. You may need to sand and adjust to get them to fit. Once the lids are in place, finish rotating the locket.

12. There will be alot of tweaking to make it all snug but still rotatable. Be patient. Depending on what you have planned for the locket. The inside of the locket can now be cut to create the storage area. (Although it could be cut at an earlier stage) As has been pointed out in some of the forums: the heart shape will be rotated in half, so any picture placed in the middle of the heart will be torn in half or will fall out the middle seam. (The movie took a few creative liberties that ignore the laws of physics.) I created a lidded box on one heart-half with gold leaf and gem-stones embedded in the other half. Alternatively you could cut a picture in half and glue half to each side. I leave this issue to your imaginative solutions. Now you are ready to Paint, Polish, and Adorn. Here is an earlier video of the semi-completed locket (3.4mb) Please email any specific questions to me if I've managed to confuse anyone. Thanks. my_oubliette@cranitorium.com

Espaol

He recibido muchas preguntas sobre los medallones que hice inspirado en la pelcula "El ilusionista". Aqu hay un video de la modelo terminado. (6,7 mb) Y aqu (por fin) son algunos de los dibujos y las instrucciones de lo que hice: 1. Ir al almacn de la mana / de artesana y comprar: (a menos que, como formas de corte) 3 obleas de corazn de madera (o un paquete con al menos 3 obleas) Paquete de clavijas eje * * Axel clavijas deben estar en el tamao que desee. El ancho de la eje afectar al tamao de algunas de las muescas que tiene que hacer en las obleas.

2. Axel clavijas

3. Corte el pin de la tapa de rotacin (medio-pins): Trabajar en la parte superior / redondeada de la primera estaca por lo que tendr la influencia de todo el eje a qu aferrarse. Forma la parte superior de la espiga, como se ilustra. Nota: la parte superior de la espiga debe ser cncava: consulte el paso 5 para ms informacin. Corte el exceso de Axel. Guarde el exceso: Se puede utilizar para hacer el pin central ms tarde. La parte inferior de la espiga se corta en forma trapezoidal (ver paso 4). La seccin central debe permanecer todo el ao. Cortar el pin en dos mitades. Este pin est diseado para fijarse a las obleas de la tapa y girar cuando las dos mitades se unen para hacer de la forma de corazn.

4. Cortar los corazones de la mitad. Hay tres capas del corazn: la tapa (parte superior), medio e inferior. Tapa (Arriba) Obleas: En las obleas de la tapa, hacer muescas trapezoidales para los pasadores de media. Los pines medio despus se pega a estas muescas.

5. Volver / inferior Obleas: Las obleas de atrs / abajo se ha muescas circulares / convexo para recibir el cabezal giratorio de la pin-tapa giratoria (media-pins). Nota: el cncavo / convexo de la naturaleza y el pasador de primera clase. Esto es para evitar que las piezas de la tapa se caiga cuando el medalln se rota entre las formas de corazn y oval. Cortar las muescas tan suave como sea posible: la tapa girar girando el perno en esta toma.

6. Wafer Medio: Muescas de la tapa giratoria pin: Corte muescas para el pasador de la tapa giratoria. Las obleas de media e inferior se sndwich de la cabeza del pasador de tapa giratoria. La muesca debe ser cortado para que coincida con el ancho de la mitad de la seccin circular del pasador de la tapa giratoria. Hacer que estos lo ms suave posible. Muescas de pin en el centro: Medida en el punto medio (eje), donde el medalln a su vez para rotar entre el valo y la forma de corazn. El centro de la vinculacin de la moneda debe estar en el centro de la lmina de medio - largo camino. He utilizado una broca pequea y un cuchillo exacto para cortar las muescas. Corte un cuadrado de lado, y la otra en forma de "cabeza de fsforo". Vea el paso siguiente para que coincida con estas muescas a la forma del centro de contactos.

7. Centro de Pin: Utilizando la paridad exceso guardado anteriormente o alguna otra madera, cortar el pin en el centro: un cuadrado lado y lado de una "cabeza de fsforo" la forma. Corte ms limpia posible para que coincida con las muescas en la oblea de media.

8. Un "lado pegamento" es donde las piezas estn pegadas entre s -, decid que era ms fcil que tratar de llamar a arriba / abajo / abajo / arriba, etc Recuerde que debe utilizar slo una fina capa de pegamento de madera buena. No deje que el pegamento se filtran

en cualquiera de las tomas de pin o partes de los no gira y los pines de presin posible. (Esto sucedi varias veces conmigo.) Pegamento Primero los pernos de media a las obleas de la tapa. (Paso diagrama # 1) Pegamento A continuacin, el extremo cuadrado del centro de contactos a la muesca cuadrada de la oblea de media. (Paso diagrama # 2) Deje que se seque tanto.

As es como la pila de obleas antes de pegar. 9. Coloque el 'cabeza de fsforo "del centro de contactos en la ranura de la lmina de media. Revise el ajuste del pasador y la muesca. Cuando se establece, debe haber suficiente friccin para mantener las dos mitades de la gira. Ajustar si es necesario. Al pegar el pin en el centro, es ms fcil de quitar las piezas de la tapa y tratar slo con la mitad inferior y obleas. Con cuidado, pegar las obleas inferior a la media obleas para asegurar el centro-pin. Utilice abrazaderas para sujetar las lminas firmemente en su lugar. Permitir que un par de das en secarse.

10. Y si eso no fuera suficientemente difcil de entender ... Aqu est la parte que es difcil de describir: Inserte las piezas de la tapa: A su vez el medalln a medio camino entre el corazn y las formas ovaladas. (Perpendicular). Las muescas convexa para el pasador de la tapa de rotacin debe ser visible. Con cuidado, gire la cabeza de alfiler en las muescas. No los obligue. Es posible que necesite ajustar la arena y conseguir que encajen. Una vez que las tapas estn en su lugar, terminar girando el relicario. 12. Habr un montn de ajustes para hacer que todo ajustado, pero todava giratoria. Sea paciente. Dependiendo de lo que hemos planeado para el medalln. El interior del medalln ahora se puede cortar para crear el rea de almacenamiento. (A pesar de que podra reducirse en una etapa anterior), como se ha sealado en algunos de los foros: la forma del corazn se girar a la mitad, por lo que cualquier imagen colocada en el centro del corazn ser rasgado por la mitad o se caen la costura del medio. (La pelcula tom algunas libertades creativas que ignoran las leyes de la fsica.) He creado una caja con tapa en un centro de la mitad de pan de oro y piedras preciosas piedras incrustadas en la otra mitad. Alternativamente, usted puede cortar una imagen en la mitad media y la cola a cada lado. Dejo este tema para sus soluciones

imaginativas. Ahora ya est listo para pintar, polaco, y adornan. Aqu est un video anterior del medalln semi-completa (3,4 MB) Por favor enviar cualquier pregunta especfica que a m si me las he arreglado para confundir a cualquiera. Gracias. my_oubliette@cranitorium.com

You might also like