Professional Documents
Culture Documents
Lab Manual 3
Lab Manual 3
Organic Chemistry
CONTENTS
Page Introduction 1. Conversion of Cholesterol to Cholestenone 2 3
2. Formation of carbon-carbon bonds The Wittig Reaction 3. Lactone Synthesis 4. Analysis of a Binary Mixture 5. Appendices
6 10 12 15
__________________________________________________________________
SCES/P3120
INTRODUCTION Laboratory Notebook: One laboratory notebook or jotter (e.g. inexpensive exercise book ) is required for recording all primary experimental data. All reaction products must be submitted.
Course Content The Course is designed so that on completion you should know of the following: (a) How to separate and identify organic compounds by classical and spectrophotometric techniques and chromatographic techniques including LC and TLC (b) How to do routine operations e.g. crystallization, distillation, sublimation, vacuum distillation, and extractions. (c) How to synthesize compounds and study reaction mechanisms The following is an approximate guide as to how you should spend your time in the lab. 1. Two organic synthesis experiments 2. Spectral and Qualitative analyses of a binary mixture 50% Credit 50% Credit
This is a final Year Organic chemistry course and you are expected to do most of the laboratory operations on your own. As a matter of routine you may have to perform recrystallizations, distillations, extractions, steam distillation, vacuum distillation and other things learnt during the earlier years. You have no excuse if you do not know them. If you are unsure or have forgotten refer back to your manuals or texts. You are also reminded not to neglect safety precautions (e.g. in anticipation of fire hazards, in handling corrosive chemicals, recovery/disposal of solvents, in handling toxic/carcinogenic/explosive chemicals). As a matter of good personal habits expected of a potential UM graduate you are to be tidy, save on chemicals and handle equipment or glassware with intelligence and care.
__________________________________________________________________
Experiment 1
CONVERSION OF CHOLESTEROL TO CHOLESTENONE Preparation of 5-cholesten-3-one and 4-cholesten-3-one from cholesterol use of a protecting group in organic synthesis In an attempt to oxidize cholesterol (I) to the corresponding ketone 5-cholesten-3one (II), it was found (L. F. Fieser, J. Am. Chem. Soc., 1953, 75, 4377, 4386) that it was not possible to obtain pure 5-cholesten-3-one. Due to the presence of a double bond , - to the alcohol group, an array of products were obtained:
HO (I)
O (II)
O O
HO
HOOC HOOC O
HO
O O
To avoid this difficulty it is necessary to temporarily remove the double bond and to regenerate it after oxidation. This is carried out by adding bromine across the double bond, and later debrominating using zinc (Note: modern reagents for carrying out the oxidation directly without affecting the double bond include PCC, TPAP/NMO, and (COCl)2/DMSO; Et3N or the Swern oxidation).
Br2 HO HO Br (III) Br Na2Cr2O7 O Br (IV) Br
Zn O (II)
(CO2H)2 O (V)
__________________________________________________________________
Procedure
Preparation of Cholesterol Dibromide (III) Add a mixture of 2.5 g bromine (caution), 0.2g anhydrous sodium acetate and 25 mL glacial acetic acid to 5 g cholesterol in 50 mL ether. After a few minutes, the mixture will precipitate as crystals. Collect these cholesterol dibromide (III) crystals by suction filtration and wash with a small amount of glacial acetic acid.
Oxidation 5,6-Dibromcholesten-3-one (IV) Transfer the cholesterol dibromide (III) into a flask containing 70 mL glacial acetic acid. Prepare a solution of 2.7g sodium dichromate in 70 mL glacial acetic acid which has been warmed to 90 oC and pour this mixture, with stirring, into the flask containing the cholesterol dibromide (III) suspension. The temperature of the mixture must be kept between 55-58 oC and the solid must dissolve within 5 minutes (if not, warm the mixture to 65 oC and most of the solids should dissolve within 10 minutes. Discard any impurities that did not dissolve). Leave the mixture to cool to room temperature (about 30 minutes). Cool the mixture in an ice-bath and add (dropwise) 25 mL water: EtOH (2:1; v/v) mixture while stirring with a magnetic stirrer for 30 minutes at 0 10 oC. 5,6-Dibromcholesten-3-one (IV) is obtained as fine white crystals, m.p. 72-76 oC. Proceed to the next step, or, if time does not permit, store these crystals in the fridge. (Note:
CrO3.2(C5H5N))
__________________________________________________________________
Question: 1. 2. Calculate the max for the compounds I V. Compare the IR and NMR spectra for both ketones (II) and (V). Write mechanisms for the transformations that you have carried out.
__________________________________________________________________
Experiment 2
WITTIG REACTION THE SYNTHESIS OF 3-PHENYLPROPENOIC ACID
Background The Wittig reaction is used to convert the carbonyl group of aldehydes and ketones into an alkene group. This reaction is named after Georg Wittig who won the Nobel Prize for the reaction in 1979. In a typical Wittig reaction, triphenylphosphine (1) reacts with an alkyl halide (2) to first form a phosphonium halide (3). Subsequently, addition of a strong base eliminates the hydrogen halide to form an ylide, alkylidenephosphorane (4) (Scheme 1).
Scheme 1
R'H2C (2)
Ph3P
X
CH2R' (3)
Ph3P
CHR'
Ph3P (4)
CHR'
The carbon of the ylide acts as a nucleophile and adds to the carbonyl group (5) to form a betaine intermediate which undergo an in situ 1,2-elimination to give the triphenylphosphine oxide (6) and an alkene (7) as the product (Scheme 2).
Scheme 2 __________________________________________________________________ 6
Ph 3 P
This experiment illustrates the general procedure with the preparation of (E)-3phenylprop-2-enoate (10) from the reaction of the ylide, methyltriphenylphosphoranylethanoate (9) and benzaldehyde. The ester which is formed (10) is then hydrolyzed with base and 3-phenylpropenoic acid (11) is then isolated as crystalline solids (Scheme 3).
Scheme 3
Br Br CO2Me Ph3P (8) Ph3P CO2Me Ph3P CO2Me (9)
CO2Me
(9) Ph O Ph (10)
CO2Me
Ph (11)
CO2H
Procedure
__________________________________________________________________
(II)
Preparation of (E)-3-phenylpropenoic acid Method 1 Dissolve the crude product (4) (3 g, 0.0089 mol) in dichloromethane (10 mL) and add to it a solution of benzaldehye (1.0 g, 0.0094 mol) in dichloromethane (10 mL). Reflux the mixture in a water bath for 1 hour. Remove the solvent to obtain a yellowish white solid containing methyl 3-phenylpropenoate. Add saturated sodium carbonate solution (20 mL) and water (100 mL) to the solid and stir the mixture vigorously for 30 min to hydrolyze the ester to an acid salt. At this stage, it is suitable to leave the mixture overnight before proceeding to the next step.
__________________________________________________________________
Method 2: Add dichloromethane (10 mL) to benzaldehyde (1g, 0.0094 mol) in a roundbottomed flask. Loosely stopper the flask, place it in an ice bath, and stir for at least ten minutes. After this time, slowly stir the crude product (4) (3 g, 0.0089 mol) and continue to stir in the ice bath for an additional ten minutes. Then allow the solution to warm up to room temperature while continuing to stir. Retrieve the stir bar from the flask and remove the solvent from the reaction mixture using a rotary evaporator. Add hexane (20 mL) to the residue in the flask and gently stir with a glass rod. The product ester is soluble in hexane but the triphenylphosphine oxide is not. Vacuum filter the solution using another 20 mL hexane to rinse the flask. Transfer the filtrate to another dry and clean round-bottomed flask. Remove hexane using a rotary evaporator. Weigh and record the melting point of the product. Characterize the product using UV and IR. Notes: 1. Methyl bromoethanoate is a lachrymator. Please use the fume-cupboard to weigh. 2. More precipitate could be obtained if the filtrate is kept overnight. 3. Distilling of about 50 mL solution is sufficient to remove any volatile compound from the reaction mixture.
QUESTIONS 1. What is the structure of the triphenylphosphoranyl ethanoate (4)? 2. Write a mechanism for formation of (E)-3-phenylpropenoic acid. 3. What is the limiting reagent in the above Wittig reaction above? __________________________________________________________________ 9
Me3CCOCH3
Procedure Preparation of Methyl-3-hydroxy-3,4,4-trimethylpentanoate Weigh 8g of granulated zinc into a 250 mL 3-necked flask with two necks closed by stoppers. Add 25 mL of bench dilute sulphuric acid to the zinc, and allow the steady reaction to proceed for 5 min by which time the metal surface should appear bright. Then, decant off the acid and wash the metal successively with water (2 x 10 mL) followed by a good grade of acetone (1 x 10 mL). After decanting off as much solvent as possible, add 30 mL of benzene, fit the flask for downward distillation and distil to a final volume of approximately 5 mL. While the flask remains warm, fit it with a mechanical stirrer, a reflux condenser and dropping funnel (Note 1), and place in the dropping funnel a mixture of pinacolone (10g), methyl bromoacetate (15.4g) in dry (Note 2) benzene (50 mL). Run in 10 mL of this solution, and observe carefully for the reaction to begin (Note 3). After the reaction has started, the remainder of the solution should be added at a rate to maintain gentle reflux ( cf. Grignard Reaction, Level II Practical ). When addition is complete, reflux the reaction until almost all the zinc has disappeared (2 3 hr). Then, cool the flask in an ice bath, and with stirring, add enough 10% H2SO4 to dissolve the Zn(OH)2.
__________________________________________________________________ 10
Notes 1. All apparatus used in this step must be thoroughly oven dried before use, and assembled while warm. Wet apparatus will result in poor yields. 2. Dried with molecular sieves or sodium 3. Gentle warming may be required. Do not add any further reagent until the reaction has begun.
Questions 1. Based on the spectra obtained, assign a reasonable structure to the product, and propose a mechanism for its formation ( Hint : acid catalysed rearrangement ). 2. What is the purpose of distilling benzene from the zinc before starting the Reformatsky reaction ?
__________________________________________________________________ 11
Guide to Qualitative Analysis of Mixtures It is necessary to separate a mixture before the individual components can be identified. Observe the physical state of unknown mixture. Do simple tests on very small amounts, e.g. solubilities in polar and non- polar solvents, acidic or basic aqueous salutions. Observe carefully if the mixture is partially soluble and if reaction occurs. These properties could form a basis for separation as well as an idea of the nature of the compound. The following are brief descriptions of possible methods of separation:(a)
Solubility Differences This involves extraction and is probably the easiest way but it is unlikely that one encounters such a simple mixture. One component can be extracted into a solvent, the other component being insoluble. This component can then be isolated by distillation or evaporation of solvent. Normally solvent with wide differences in polarity are tried first, e.g. water and petroleum ether. Some examples where this method will work are sucrose/naphthalene, acetamide/ diphenyl and glycine hydrochloride/benzophenone, where contrasting differences in polarity of the components exist.
(b)
Chemical Differences A derivative is made and this is separated from the other components by precipitation or extraction.* The usual type of derivative is formation of a salt, e.g. if given an acidic/neutral mixture insoluble in water, the acidic component can be extracted into aqueous basic solution. Similary, a phenol/neutral mixture can be treated in the same way as most phenols are sufficiently acidic to be extracted into aqueous sodium hydroxide. For a basic/neutral mixture, extraction into aqueous acid will effect a
__________________________________________________________________ 12
* Caution:
compounds may be troublesome, so it is best to avoid too much of aqueous reagents. A mixture of a phenol and a ketone with - hydrogens would both dissolve in NaOH. Solution of the phenol may be effected with very dilute NaOH and done rapidly to avoid decomposition of the carbonyl compound. Some amines form salts which may not dissolve readily in H2O, a different acid may be used. (c) Boiling Points Differences Two liquids which do not form a constant boiling point mixture and have widely separated boiling points can be separated by fractional distillation using a simple fractionating column. The boiling points must be at least 25 0C apart. For high boiling mixtures this can be done under reduced pressure, preferably under nitrogen if the compound decomposes. ( d)
Recrystallization Often one component can easily be obtained from a mixture by a suitable choice of solvents for recrystallization
(e)
Chromatography Methods. Generally TLC, LC, GLC and other chromatographic methods are extremely effective separation methods but they can be long and tedious and furthermore are limited to small scale work involving less than 1g. unless appropriate facilities are available. The above methods should only serve as a guide as there can be no hard and fast rules. Usually, methods (b) and (c) would be suitable. Note also that many problems could arise in the process of recovering the separated components (refer text). In principle, all the given amounts should be recoverable unless they are accidently thrown away or are extremely volatile. It may be wise to try a small scale separation
__________________________________________________________________ 13
References: 1. Shriner, Hermann, Morrill, Curtin, and Fuson, The Systematic Identification of Organic Compounds (Wiley). 2. Furniss, Hannaford, Smith, and Tatchell, Vogels Textbook of Practical Organic Chemsitry (Longman). 3. Williams and Fleming, Spectroscopic Methods in Organic Chemistry (McGraw-Hill). 4. Silverstein and Webster, Spectrometric Identification of Organic Compounds (Wiley).
__________________________________________________________________ 14
__________________________________________________________________ 15
Appendix 1 CHROMATOGRAPHY The various types of chromatography is summarized in the Diagram below.
Chromatography
Gas
Liquid Chromatography
chromatography
Ion exchange Liquid/ solid Liquid/ liquid chromatography chromatography LSC LLC Thin layer TLC Paper PC
Exclusion
Liquid liquid chromatography LLC is partition chromatography. The sample is retained by partitioning between the mobile liquid and the stationary liquid, e.g in paper chromatography the stationary phase is water held on the fibres of cellulose. Liquid solid chromatography LSC is adsorption chromatography. In column or thin layer TLC the sample is adsorbed on the adsorbent silica gel or alumina. In practice silica gel or alumina has varied amounts of moisture so that the chromatography is a combination of LLC and LSC. Exclusion chromatography uses a highly porous material or gel which separates compounds (usually polymers) according to the molecular size. Ion exchange uses ionic groups bonded into a polymeric resin. Ionic coumpounds ( e.g. amino acids ) have different affinities to the resin and can be separated. Bonded phase chromatography BPC is similar LSC or LLC except that the absorbent material is chemically modified silica gel or similar substance. The OH groups of silica gel can be silated and various organic groups can be attached as shown below
_____________________________________________________________________ 16
Bonded phases are advantageous as different polarity types may be synthesized and both organic or aqueous solvents can be used. When using aqueous organic solvent mixture it may be noted that the less polar material absorb on the stationary phase while the more polar compounds are eluted by the polar aqueous eluant . This is referred to as reverse phase chromatography. A summary of the LC types and adsorbents is given in the tables below.
_____________________________________________________________________ 17
Liquid liquid
LLC
Partition and / or adsorption Paritition and / or adsorption Adsorption on Fixed Ionic Site Diffusion into Pores
LIQUID SOLID ADSORBENTS Adsorbent Silica Alumina Charcoal Chemical Structure ( SiO2 )x ( Al2 O3 )x Estimated Usage % 70 20 1 Surface Properties Slightly acidic Silightly basic * Graphitized nonpolar , Oxidized Polar (silightly basic) Strongly acidic Application General purpose General purpose Sample cleanup
Florisil
General purpose adsorbent Phenols and aromatic nitro compounds Very polar compounds
Polyamides
Basic
Relatively nonpolar
High Pressure Liquid Chromatography ( HPLC ) The obvious drawback of column chromatography is the tedium of eluting the sample out of the column . To speed up the process high pressure may be used to force in the eluant through the column. By using high pressure up % to 4000 psi. it is necessary to use stainless steel columns. A high pressure liquid chromatography system consists of a solvent pump, plumbing connections, injection port for a sample introduction, a detector to detect the eluted samples and a recorder to give a graphic output representation. For compounds absorbing UV radiation a UV detector is convenient. Read up on the instrument, and the operating instructions.
_____________________________________________________________________ 19
Caution: Read & understand the instrument first. Consult lecturer & lab. Assistant in charge. Handle microsyringe with loving care.
Column Chromatography ( CC ) or Liquid Chromatography ( LC ). CC or LC is an example of adsorption chromatography. It consists of a stationary solid phase, known as the adsorbent, supported in a column and of mobile liquid phase which is allowed to flow down the column. This is referred to as the eluant.
The mixture to be separated is introduced onto the adsorbent at the top of the column in solution form. The two components will be adsorbed to different extents depending upon the polarity of the molecules. The eluant is introduced and allowed to flow down the column. The components of the mixture will undergo many adsorption desorption processes as they pass down, the least polar molecule moving more quickly. Compound Elution Sequences* Hydrocarbons Olefins Ethers Halogen Compounds Aromatics Ketones Aldehydes EstersAlcohol, amines, mercaptans Acid and strong bases. General order of elution
_____________________________________________________________________ 20
Eluotropic Series* Petroleum ether Cyclohexane Carbon tetrachloride Benzene Methylene chloride Chloroform (alcohol free) Diethyl ether Ethyl acetate Pyridine Methanol Acetone n- Propanol Ethanol Acetic Acid
Increasing Polarity
The type of adsorbent chosen also effects the speed at which the compounds are eluted. The more active the adsorbent the more slowly the compounds will move down the column.
Adsorbents for Adsorption Chromatography* Cellulose Starch Sugars Magnesium silicate Calcium sulphate Silicic acid Florisil Magnesium oxide (magnesia) Aluminium oxide (alumina) Activated Chareoal
By suitable choice of adsorbent and eluant it is possible to separate compounds of similar chemical constitution. If two molecules are very similar it is necessary to _____________________________________________________________________ 21
Thin layer chromatography (TLC) is a modification of column chromatography. In this case the adsorbent is supported on a flat surface. To develop the chromatogram the plate is placed vertically in a tank containing the eluant which flows upwards by capillary action. Unlike column chromatography it is not possible to alter the polarity of the solvent during development of the chromatograph but by using suitable proportions of mixed solvents a separation is usually achieved.
Silica-gel and alumina are the most common adsorbents. For T.L.C. those are usually combined with Plaster of Paris which acts as a binding agent.
As in paper chromatography, a Rf value can be calculated where R : distance moved by compound distance moved by solvent front.
If the components are colourless they can be detected by various means, eg using U.V. light, iodine vapour or charring with sulphuric acid.
The great advantage of T.L.C. is its short development time, usually of the order of 30 mins.
Gas-liquid Chromatography (GLC) proceeds mainly by partition chromatography i.e. separation depends upon the different solubilities of the components at equilibrium between the gas and liguid phase. The stationary phase is a liquid supported on a solid contained in a tube. The mobile phase is an inert gas which also acts as a carrier of the mixture. This mixture can be solid, liquid or gaseous. _____________________________________________________________________ 22
After separation the components & carrier gas pass through a detector which indicates when a compound is being eluted by drawing a curve on chart paper. The area under the curve can be considered to be proportional to the number of moles eluted.
The compounds can be characterized by their Retention Times i.e. the time taken from being injected to being eluted under set conditions.
The solution is filtered through a fluted filter paper under gravity. While filtering this crystals may be deposited. This can be avoided by (a) Warning the funnel and receiving conical flask. (b) Having prepared a hot saturated solution, adding more solvent, filtering and evaporating until the original volume is obtained.
After cooling to R.T. crystallization can be encouraged by (a) cooling in ice (b) scratching and (c) seeding addition of the crystal of solute.
The crystallized compound is collected by suction filtration and washed to remove mother liquor.
From Mixed Solvents The two solvents must be miscible and are chosen such that the compound is soluble in solvent I and insoluble or appreciably less soluble in solvent II. A hot solution is prepared in solvent I. After filtering solvent II is added dropwise until the solution just turns cloudy. On cooling crystals are formed.
Choosing a solvent A suitable solvent is found by trial and error, and this should be conducted on a small scale. The aim is to find a solvent or combination of solvents in which the solute is soluble at high temperatures and much less soluble at room temperature.
_____________________________________________________________________ 24
Recrystallisation is used for purifying a compound which is contaminated with one more other compounds. These may have similar solubilities to the major component but as they are present in smaller amounts they can be separated by one or more recrystallisations
Fractional crystallization is the separation of two components of similar solubility and present in comparable amounts by successive crystallizations and recombination of fractions. During this process the first component becomes more and more concentrated in the crystals and the mother liquor becomes more enriched with the second component. This is a tedious way of separating two components.
_____________________________________________________________________ 25
See Renfrow Hawkins, Organic Chemistry Laboratory Operations p 13, 147 Louis F. Fieser, Organic Experiment p.30
_____________________________________________________________________ 26
_____________________________________________________________________ 27
_____________________________________________________________________ 28
_____________________________________________________________________ 29
See: Renfow Hawkins, Organic Chemistry Laboratory Operation, m.s. 13, 147 _____________________________________________________________________ 30
The pressure at which the liquid boils is measured by a manometer. The most common type is a closed-end monometer.
The pressure in the closed arm is zero. This manometer is kept closed off from the system as solvent vapour can dissolve in the mercury. Then the pressure in the closed arm will no longer be zero, resulting in an uncorrect reading. This type of manometer is accurate up to a few millimeters of mercury.
J.A. Elvidge and P.G. Sammes. A course in Modern Techniques of Organic Chemistry p. 115.
_____________________________________________________________________ 31
_____________________________________________________________________ 32
_____________________________________________________________________ 33
Appendix 6 I.R
IR samples All samples must be DRY. Test first to ensure that your sample is NOT water or in an aqueous solution. Water will dissolve away the NaCl cells which are rather expensive (RM 600) . Solids can be dried in a vacuum dessicator. Liquids can be used neat between NaCl plates. Solids can be micro-pelleted with KBR. Liquids and solids if soluble in CCl4 or CS2 can be used in solution cells. Spectral grade CHCl3 may be used for less soluble compounds. Note the bands cut off when solvents are used. Solids can be mulled in Nujol but note the bands cut off by Nujol ( hydrocarbon oil ) If you get poor spectra go to the instrument room and instruct the lab. assistant as to your requirements.
_____________________________________________________________________ 34
_____________________________________________________________________ 35