Professional Documents
Culture Documents
C-FS11
Fastening
Solutions
When performance is critical
Sometimes you need a fastener that does more. Maybe youre looking for higher loads or additional corrosion resistance, or perhaps an installation method that saves time on a repetitive application. Whatever it is, you are no longer looking for just a fastener, what you are really looking for is a solution. When faced with such challenges look to Simpson Strong-Tie. We specialize in these performance-critical challenges, offering fasteners and installation systems that uniquely suit the applications for which they are intended. By blending field research with insightful design and the highest-quality materials, we are able to offer premium fastening products with the features that ensure a successful result for almost any application. For more information about how we may be able to help you on your next project, please call (800) 999-5099 to speak with one of our knowledgeable, jobsite-trained fastening professionals. To learn more, visit: www.strongtie.com/fasten
Structural
Stainless
Quik Drive
Systems
Specialty
TABLE OF CONTENTS
GENERAL INFORMATION
Coatings and Materials ........................................................... 12-13 Corrosion Information ............................................................ 10-11 Fastener Overview .................................................................. 14-15 How Self-Drilling Screws Work ............................................. 16-17 Important Information and General Notes ..................................... 8 Warranties and Warnings ........................................................ 8-10 Full Round Head, Spiral Shank ................................................ 53 Full Round Head, Smooth Shank ............................................. 54 31-34 Paper-Tape Collation 31-34, Clipped Head, Ring Shank .......................................... 55 33, Full Round Head, Ring Shank .......................................... 62 31-34 Plastic-Strip Collation, Full Round Head, Ring Shank ...... 55 33 Tape Collation, DA-Style Head Angled Finishing ................... 62 Adhesive Collation 20 T-Style Head Angle Finishing ............................................ 63 25 FN-Style Head Angle Finishing ........................................... 62 16 Gauge Straight, T-Style Head, Finishing ............................... 63 18 Gauge Straight, T-Style Head, Brads ................................... 64 23 Gauge Straight, Micro Pins ................................................. 64 Inserted-Plastic-Coil Collation 0 Full Round Head, Ring Shank ............................................. 61 15 Full Round Head, Ring Shank ........................................... 61 L Series Flooring Cleats ............................................................... 68 T Series Flooring Cleats ............................................................... 68
TABLE OF CONTENTS
HAND-DRIVE SCREWS (cont.)
Self Drilling, Hex Washer Head, Sealing Washer ....................... 112 Self Drilling, Pancake Head, Standing Seam Roofing, Stainless Steel ....................................................................... 107 Self Drilling, Wire-Lath Modified Truss Head, Stainless Steel .... 107 Self Drilling, Trim Head, Siding, Stainless Steel ........................ 106 Self Drilling, Truss Head, Stainless Steel ................................... 108 Self Drilling, Wafer Head with Wings, Stainless Steel ................ 110 Storm-Panel Screw, Stainless Steel ........................................... 112 Strong-Drive SD8 Wafer-Head Screw ........................................ 100 Trim Head Decking, Coated .......................................................... 86 Trim Head Decking, Stainless Steel ....................................... 87-89 Trim Head, Sealing Washer, Stainless Steel ............................... 102 Truss Head, Stainless Steel ........................................................ 103 Wire-Lath Modified Truss Head, Stainless Steel ........................ 102
Search our extensive line of collated nails based on the tool you own.
Novices and pros alike can easily search based on what they know about the fastener they are looking for.
The Fastener Finder provides both hand-drive and collated options, including fasteners for our Quik Drive auto-feed screw driving systems.
Results show all model numbers and available packaging sizes to make ordering easy.
COMPANY INFORMATION
For more than 50 years, Simpson Strong-Tie has focused on creating structural products that help people build safer and stronger homes and buildings. A leader in structural systems research and technology, Simpson Strong-Tie is one of the largest suppliers of structural building products in the world. The Simpson Strong-Tie commitment to product development, engineering, testing and training is evident in the consistent quality and delivery of its products and services. Simpson Strong-Tie product lines include: Structural connectors for wood and Simpson Strong-Tie Anchor Systems anchors and fasteners for concrete and cold-formed-steel construction masonry Strong-Wall prefabricated shearwalls Simpson Strong-Tie Fastening Systems Strong Frame ordinary moment frames Connectors for Cold-Formed Steel ATS Anchor Tiedown systems for Curtainwalls multi-story buildings For more information, visit the companys Web site at www.strongtie.com. The Simpson Strong-Tie Company Inc. No Equal pledge includes:
Quality products value-engineered for the lowest installed cost at the highest rated performance levels Most thoroughly tested and evaluated products in the industry Strategically-located manufacturing and warehouse facilities National code agency listings Largest number of patented connectors in the industry European locations with an international sales team In-house R&D, and tool and die professionals In-house product testing and quality control engineers Member of AITC, ASTM, ASCE, AWPA, ACI, AISC, CSI, ICFA, NBMDA, NLBMDA, SDI, SETMA, STAFDA, SREA, NFBA, WTCA and local engineering groups.
18-29
Hand-Drive Nails
30-50
Collated Nails
51-64
Collated Staples
65-74
75-84
Hand-Drive Screws
85-113
114-133
Tom Fitzmyers
Chief Executive Officer
Terry Kingsfather
President
134-156
157-191
800-999-5099 | www.strongtie.com
All rights reserved. This catalog may not be reproduced in whole or in part without the prior written approval of Simpson Strong-Tie Company Inc.
GENERAL NOTES
These notes are provided to ensure proper selection and installation of Simpson Strong-Tie Company Inc. products and must be followed carefully. a. Simpson Strong-Tie Company Inc. reserves the right to change specifications, designs and models without notice or liability for such changes. b. Do not exceed published loads, doing so could jeopardize the connection. c. A fastener that splits the wood will not take the design load. Evaluate splits to determine if the connection will perform as required. Dry wood may split easily and should be evaluated as required. If wood tends to split consider pre-boring holes with diameters specified in the 2005 Edition National Design Specification (NDS) section 11.1.5 for nails and 11.1.4 for screws. d. Unless otherwise noted, dimensions are in inches, loads are in pounds and shear loads are applied perpendicular to edge. e. Unless otherwise noted, nail penny size does not imply specific diameters or load capacities. Design standards must be used in conjunction with fastener material, diameter and length to determine acceptable uses. f. Dissimilar metal combinations should be carefully assessed and avoided if possible. g. Fasteners may break if driven into hard materials or if countersunk below the surface of the substrate fastened. h. All carbon steel based fasteners do have the potential to corrode and rust. i. Use Quik Drive tools only with authentic Quik Drive fasteners. Other fasteners will void the warranty and may cause the tool to malfunction and become damaged. j. If a Quik Drive product is compatible with a specified tool, do not use the product with any other tool. k. Do not overdrive fasteners. Overdriven fasteners may have a reduction in shear and pull-through capacity. l. Some hardened fasteners may have premature failure if exposed to moisture. These fasteners are recommended to be used in interior dry conditions. m. Pneumatically driven fasteners may deflect and injure the operator or others. Follow the manufacturers instructions and use the appropriate safety equipment. n. Choose the proper tool to suit the fastener and applications. o. Use products only in accordance with all instructions. p. All specified fasteners must be installed according to the instructions in this catalog. q. Use proper safety equipment and follow all safety instructions. r. Always wear protective eyewear. 8 s. There are many choices of fasteners, tools and other products. It is often difficult to determine which type of product is best suited for your application. In some cases, there may be more than one type of product that will work well. The information in this catalog is intended to guide the Designer toward the product best suited for the specific application, use and environment. The choice of which product to use should be made by a qualified Designer. t. All connected members and related elements shall be designed by the Designer. u. Select fasteners of a type, size, length, thread, head, coating, material, point and other characteristics suitable for your application, use and environment. Incorrect fastener selection may cause the connection to fail. v. Select a fastener only after reading the corrosion information on pages 10-13 of this catalog. w. If using a fastener from this catalog with any other Simpson Strong-Tie product, consult the appropriate Simpson Strong-Tie catalog or www.strongtie.com for detailed information concerning the other product. x. Some fasteners have load ratings, and others do not. Fasteners that are not load rated should not be used in any structural application. y. Be aware of special conditions that may increase corrosion risk and select product accordingly. z. Test fasteners in mockup of assembly to assure fasteners properly install. aa. With the use of any power or pneumatic tools, follow manufacturers safety instructions. bb. Austenitic stainless steel screws are softer by nature and have less torsional strength than many other types. Simpson Strong-Tie cannot assume any liability for breakage or damage due to breakage during or after installation. Pre-drilling may be necessary in some cases. For best results drive at 2500 RPM or less. cc. The term Designer used throughout this catalog is intended to mean a licensed/certified building design professional, a licensed professional engineer or licensed architect. dd. Follow manufacturers installation instructions and fastener recommendations. This catalog includes all information available as of the effective date of publication. Please consult www.strongtie.com for current information.
INDEMNITY
Customer or Designers modifying products or installation procedures, or designing non-catalog products for fabrication by Simpson Strong-Tie Company Inc. shall, regardless of specific instructions to the user, indemnify, defend, and hold harmless Simpson Strong-Tie Company Inc. for any and all claimed loss or damage occasioned in whole or in part by non-catalog or modified products.
LIMITED WARRANTY
This Limited Warranty must be read in conjunction with the General Notes, Corrosion Information, and Terms & Conditions of Sale. Simpson Strong-Tie Co. Inc. (Simpson) warrants catalog products to be free from defects in material or manufacturing. Simpson products are further warranted for adequacy of design when used in accordance with design limits in this catalog, and properly specified and installed. This warranty does not apply to products used not in compliance with specific applications and installation procedures set forth in this catalog, or to non-catalog or modified products, or to deterioration due to environmental conditions. Simpson products are designed to the load capacities and uses listed in this catalog. Properly installed Simpson products will perform in accordance with the specifications set forth in the applicable Simpson Strong-Tie catalog. Additional performance limitations for specific products may be listed on the applicable catalog pages. Due to the particular characteristics of potential impact events, the specific design and location of the structure, the building materials used, the quality of construction, and the condition of the soils involved, damage may nonetheless result to a structure and its contents even if the loads resulting from the impact event do not exceed Simpson Strong-Tie catalog specifications and Simpson Strong-Tie products are properly installed in accordance with applicable building codes. All warranty obligations of Simpson shall be limited, at the discretion of Simpson to repair or replacement of the defective part(s). These remedies shall constitute Simpsons sole obligation and sole remedy of purchaser under this warranty. This warranty may change periodically consult this website for current information. SIMPSON DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT WILL SIMPSON BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL, PUNITIVE OR SPECIAL DAMAGES OR DIRECT OR INDIRECT LOSS OF ANY KIND, INCLUDING BUT NOT LIMITED TO PROPERTY DAMAGE AND PERSONAL INJURY. SIMPSONS ENTIRE LIABILITY IS LIMITED TO THE PURCHASE PRICE OF THE PRODUCT. SOME STATES DO NOT ALLOW LIMITATIONS ON IMPLIED WARRANTIES, OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
IMPORTANT INFORMATION
ADDITIONAL QUIK DRIVE SAFETY WARNINGS
SAFE WORK AREA
a. Keep work area clean and well lit. b. Do not operate Simpson Strong-Tie Quik Drive tools in dangerous environments. Do not expose tools to rain, or use them in damp or wet locations. Do not use Quik Drive tools in the presence of flammable liquids, dust or gases, as they can create sparks. c. Keep bystanders, children and visitors away while operating a Quik Drive Tool. Distractions can cause accidents and serious bodily injury. b. the tool. Inattention while operating Quik Drive tools may result in serious bodily injury. Dress properly when using a Quik Drive tool. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, long hair or jewelry can be caught in moving parts and result in serious bodily injury. Be sure the power switch on a Quik Drive tool is in the off position before plugging in the tool. Do not carry tools with your finger on the switch. Keep proper footing and balance at all times. Always use safety equipment such as wearing protective glasses, dust masks, non-skid safety shoes, safety harnesses hard hats and/or earplugs.
c. d. e.
PERSONAL SAFETY
a. Stay alert. Do not use a Quik Drive tool while tired or under the influence of drugs, alcohol or medication. Use common sense when operating
5. Use the chart below, which is based on Simpson Strong-Tie testing and experience, to select the fastener coating or material.
If the material or preservative-treated wood product to be used is not show on the chart, Simpson Strong-Tie has not evaluated it and cannot make any other recommendation than the use of coatings/materials shown in the high category shown below. Manufacturers may independently provide test results or other product use information; Simpson Strong-Tie Company Inc. expresses no opinion regarding such information.
Interior Dry
Environment
ACZA
Other or Uncertain
Exterior
1. For preservative-treated lumber used above ground, with actual retention levels higher than 0.05 pcf for CA-C, 0.06 pcf for MCA and CA-C, 0.08 for CA-B, 0.15 pcf for MCQ and 0.2 pcf for ACQ, types 304/305/316 stainless-steel, copper or silicone bronze fasteners are recommended. 2. Borate treated woods are not appropriate for outdoor use. 3. Test results indicate that mechanically galvanized (C-3, N2000 and class 55) and Quik Guard will perform adequately, subject to regular maintenance and periodic inspection. However, the test protocol followed was a modified version of the nationally recognized test method AWPA E12-94. This test method is an accelerated test, so data over an extended period of time is not available. Also noteworthy is that tests run in a laboratory may not correlate to service conditions. If uncertain, use types 304/305/316 stainless steel. 4. Some treated wood may have excess surface chemicals making it potentially more corrosive. If you suspect this or are uncertain, use types 304/305/316 stainless steel, copper or silicon bronze. 5. Ammonia is typically used as a chemical carrier for difficult to treat wood species, such as, but not exclusive to, Douglas Fir and Hem Fir, which are usually found in the western United States. Amine carriers are used in some of the eastern species, such as Southern Yellow Pine. If uncertain, verify chemical with wood treater. 6. Type 316 stainless-steel fasteners are the minimum recommendation for ocean-salt air and other chloride environments.
Higher Exposure
For the latest Simpson Strong-Tie coating information and additional technical information on this topic, visit our website at www.strongtie.com/info.
11
Electrocoating (ECoat)
Electrocoating utilizes electrical current to deposit the coating material on the fastener. After application the coating is cured an oven. Electrocoating provides a minimum amount of corrosion protection and is intended for dry, non-corrosive applications only.
Yellow Zinc
Electroplated zinc applied in accordance with ASTM F1941. In the ASTM B117 salt spray test yellow zinc provides 24 hours of protection before the first appearance of red rust.
Gray Phosphate
Gray phosphate provides a minimum amount of corrosion protection and is intended for dry, non-corrosive applications only.
Black Phosphate
Black phosphate provides a minimum amount of corrosion protection and is intended for dry non-corrosive applications only.
Mechanically-applied zinc in accordance with ASTM B695, Class 55 with a supplementary overcoat. Mechanically galvanized, Class 55 fasteners are compliant with the 2006 International Residential Code (R319.3) and the 2009 International Residential Code (R317.3)
Quik Guard
Quik Guard is a proprietary double-barrier coating that consists of an electrodeposited base layer with organic paint layer. In the ASTM B117 salt spray test Quik Guard has less than 10% of surface red rust at 950 hours.
Double Barrier
The Simpson Strong-Tie double-barrier coating is a proprietary two-layer coating that provides a level of corrosion protection that is equivalent to ASTM A-153 hot-dip galvanization.
Teal-Arrow Icon
Throughout this catalog this icon identifies coated fasteners that Simpson Strong-Tie classifies as possessing a medium level of corrosion resistance, making them suitable for use in some exterior and corrosive environments and with some preservative-treated woods. For applications in higher-exposure applications, type-300 series stainless-steel fasteners should be considered for superior corrosion resistance. Additional important information on pages 10-13 should be reviewed before selecting a fastener for a specific application.
12
Copper
The copper used for the manufacture of fasteners contains a minimum of 98% copper in accordance with ASTM F1667. Copper fasteners are compliant with the 2006 International Residential Code (R319.3), 2006 International Building Code (2304.9.5), 2009 International Residential Code (R317.3) and the 2009 International Building Code (2304.9.5.1).
Silicon Bronze
Silicon Bronze is a copper alloy with silicon used as an alloying element. Fastener made from silicon bronze are compliant with the 2006 International Residential Code (R319.3), 2006 International Building Code (2304.9.5), 2009 International Residential Code (R317.3) and the 2009 International Building Code (2304.9.5.1).
General note about salt spray testing: Salt spray testing in accordance with ASTM B117 is not intended to represent real-world corrosion
performance of screw coatings. It should only be used for comparative evaluation between like products. Many variables may affect the outcome of the salt spray test such as screw features, coating types, post-coating processes, etc.
TRADEMARK ATTRIBUTION
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
4-Cut, Accuset, AEG, Airco, Airy, Akuzuki, Apach, Archer, Arrow, Atro, Atlas Copco, BeA, Besco, Black & Decker, Bosch, Bostitch, Cadex, Campbell Hausfeld, Central Pneumatic, Chicago Pneumatic, Craftsman, Craftex, DeWalt, Duo-Fast, Eagle, EB-TY, E-Coat, E-Z Fasten, Fasco, Freeman, Grex, Grip-Rite, Grizzly, Haubold, HighPro, Hilti, Hitachi, ISM, Jamerco, Makita, Marutex, Max, Maxus Leland Master Gripper, Masterpower, Metabo, Milwaukee, Monel, Mylar, N2000, Northern Tool, Numax, Palmgren, Paslode, Phillips, Pneutools, Porta-Nails, Porter Cable, Powernail, Prebena, Primeair, Primatech, Porter Cable, Ramsond, Rigid, Senco, Sioux, Snap-On, Spotnails, Stanley, Stan-Tech, Supco, Superior, Surebonder, Trex and Trex Transcend, Wen and Westward are all registered trademarks of their respective companies.
13
FASTENER OVERVIEW
NAILS
Nail Sizes
The most common method used to represent nail sizes is the penny size, which is a length designation. The size is written with a number and the abbreviation d for denarius which is Latin for penny. While referring to penny size and type designations such as box or common is a typical method for calling out nails, it is more accurate and reduces potential confusion if the nail is called out by diameter and length.
Nail Types
Box: A wire nail with a round head, these nails have a smaller shank diameter than common nails of the same penny size. Brads: A common term used for nails less than 1 14" in length with a head slightly larger than the shank. These nails can be easily concealed by countersinking below the work surface. Casing: A wire nail with a head that is only slightly larger head than a finish nail, often used for flooring. Common: A common construction wire nail with a round head. Common nails have larger shanks than box nails of the same penny size. Finishing: A wire nail with a head that is only slightly larger than the shank. These nails can be easily concealed by countersinking below the work surface. Roofing: A nail used for attaching paper or shingle to roof battens or sheathing; usually with a large flat head. Siding: A wire nail with a shank that is typically 0.99" or less in diameter and a smaller head than other nails of the same size to help conceal the fastener after installation.
Smooth Shank
Spiral Shank
FASTENER OVERVIEW
SCREW FEATURES
Head Styles
Flat Head
Bugle Head
Trim Head
Cap Head
Truss Head
Pan Head
Pancake Head
Washer Head
Thread Styles
Coarse Threads
Twin Threads
Tapping Threads
Box Threads
High-Low Threads
Point Styles
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
Sharp Point Application: Wood and thin metal (18 gauge or thinner)
Type-17 Point Application: Wood, composite and thin metal (18 gauge or thinner)
Drill Point Application: Metal (see pages 16-17 for more information)
4"
1 58"
Measure all other screws from top of head to point
Measure pan, pancake, truss, washer and hex head screws from under head to point
15
Definitions
RPM: The speed at which the screwdriver motor runs while the screw is installed. This is often adjustable using a variable-pull trigger or different driver motor. Applied Force: A measure of how hard the user pushes as the screw is installed. Work Material Hardness: Can be viewed as a materials resistance to drilling or cutting. In most instances, the harder the work material, the harder it is to cut. Depending on the application, this may be outside the users control.
* Suggested maximum values. Stated speeds may require a variable-speed screwdriver motor and a partial trigger-pull. Harder material may require slower speeds and less applied force.
Additional Considerations:
Screw Drill-Point Material: Typically plain carbon steel which is less stable at high temperature than equivalent high-speed steel (HSS) drill-bits. Reduced Screwdriver-Motor RPM: This may actually decrease installation time by allowing the user to push harder during installation.
When selecting a self-drilling screw design, it is important to consider the material thickness and type of materials to be joined. There are key design features to consider when selecting a suitable fastener for a specic application.
Head
Drill Flute
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
The utes allow drilled material to exit the hole. Once the utes become completely embedded in the material, they can no longer remove the chips cut from the work material. Since these chips contain approximately 80% of the heat created by the drilling process, this can cause the point to over-heat and fail.
Threads
Point Length
The length of the drill point determines the material thickness which the screw can reliably penetrate. The unthreaded portion of the point, known as the pilot section, must be long enough to completely drill through the material before the threads engage. Since the threads advance faster than the drilling process, if they engage before drilling is done the fastener can bind and break.
Flute
Point Length
Point
Winged Reamer
Wings ream hole larger than threads so threads will not engage wood.
Wings break off when they hit steel, then threads engage.
16
Steel Thickness
Gauge 25 22 20 (drywall) 20 (structural) 18 16 14 12 Mils 18 27 30 33 43 54 68 97 Design Thickness (in.) 0.0188 0.0283 0.0312 0.0346 0.0451 0.0566 0.0713 0.1017 (mm) 0.48 0.72 0.79 0.88 1.14 1.44 1.81 2.58 Minimum Thickness (in.) 0.0179 0.0269 0.0296 0.0329 0.0428 0.0538 0.0677 0.0966 (mm) 0.45 0.68 0.75 0.84 1.09 1.37 1.72 2.45
#2
#3
#4 #5
1. One mil is 1/1000 (0.001) of an inch. Mil thickness measures the uncoated based material.
Work material too hard Insufficient chip clearance Excessive force (feed) applied while drilling
Confirm work material specs Choose screw with longer pilot section Reduce application force
Drill motor set on reverse Work material too hard Drill point blunted by handling
17
HAND-DRIVE NAILS
Cedar and Redwood Decking Types 304 and 316 stainless steel, page 31
COLLATED NAILS
20-22 Plastic Strip, Full Round Checkered Head, Ring Shank Types 304 and 316 stainless steel and silicon bronze, page 52
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
Preservative-Treated Wood Decking Types 304 and 316 stainless steel, page 32
20-22 Plastic Strip, Full Round Smooth Head, Screw Shank Types 304 and 316 stainless steel, page 53
20-22 Plastic Strip, Checkered, Casing Head, Ring Shank Type 304 stainless steel, page 53
18
HAND-DRIVE SCREWS
Trim-Head Decking Coated, page 86
Types 305 and 316 stainless steel, page 87 Painted head, types 305 and 316 stainless steel, pages 88-89
Bugle-Head Wood Decking Types 305 and 316 stainless steel, pages 90-92 Painted head, type 305 stainless steel, page 92 31-34 Paper Tape, Clipped Smooth Head, Ring Shank Types 304 and 316 stainless steel, page 55
Dexxter Composite Decking Coated and types 305 and 316 stainless steel, page 93 Painted head, type 305 stainless steel, page 94
Composi-Lok Composite Decking Coated and type 305 stainless steel, page 95
28 Wire Weld, Clipped Smooth Head, Ring Shank Type 304 stainless steel, page 56
Hardwood Decking Flat and trim head styles, types 305 and 316 stainless steel, page 96 Painted head, types 305 and 316 stainless steel, page 97
Flat Head Trim Head
DHPD Hardwood Decking, Stainless Steel Type 305 stainless steel, page 97 15 Wire Coil, Full Round Checkered Head, Ring Shank Types 304 and 316 stainless steel, page 57
19
HAND-DRIVE NAILS
Cedar and Redwood Siding Types 304 and 316 stainless steel, page 33
COLLATED NAILS
15 Wire Coil, Full Round Checkered Head, Ring Shank Types 304 and 316 stainless steel, page 58
Shake and Shingle Siding/Roofing Types 304 and 316 stainless steel, page 34
Painted Siding Types 304 and 316 stainless steel, pages 35-36
15 Wire Coil, Full Round Checkered Head, Ring Shank, Fiber-Cement Siding Type 304 stainless steel, page 58
15 Wire Coil, Painted, Full Round Checkered Head, Ring Shank Type 304 stainless steel, page 59
20
HAND-DRIVE SCREWS
Hex-Washer Head Type 316 stainless steel, with and without bonded washer, page 101
Wire-Lathe Modified Truss Head Type 305 stainless steel, page 102
COLLATED STAPLES
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
16 Gauge, 716" Crown Types 304 and 316 stainless steel, page 65
Fiber Cement, Wafer Head Type 316 stainless steel, page 101
Fiber Cement, Wafer Head Self drilling, type 410 stainless steel, page 106 16 Gauge, 12 " Crown Types 304 and 316 stainless steel, page 66
Trim Head Siding Self drilling, type 410 stainless steel, page 106
Modified Truss Head, Wire Lathe Self drilling, type 410 stainless steel, page 107
21
Roofing
Simpson Strong-Tie offers a wide assortment of fasteners for all kinds of roofing applications. Whether the project calls for slate, tile or wood shingles or metal roofing, our selection of stainless steel, copper and aluminum fasteners offers long-lasting performance.
HAND-DRIVE NAILS
Shake and Shingle Siding/Roofing Types 304 and 316 stainless steel, page 34
COLLATED STAPLES
16 Gauge, 716 " Crown Types 304 and 316 stainless steel, page 65
HAND-DRIVE SCREWS
Hex-Washer Head Type 316 stainless steel, with and without bonded washer, page 101
Roofing, Tile and Slating Types 304 and 316 stainless steel, copper and aluminum, pages 38-41
Truss Head Self drilling, type 410 stainless steel, page 108
COLLATED NAILS
15 Wire Coil, Full Round Smooth Head, Roofing Types 304 and 316 stainless steel, page 60
Pancake Head, Standing-Seam Roofing Clips Self drilling, type 410 stainless steel, page 107
22
Framing
Simpson Strong-Tie nails meet the toughest requirements for quality and corrosion resistance. Framing, deck/dock construction and permanent wood foundations will all stand the test of time when our fasteners are used in their construction. Our nails are available with smooth, ring and screw shanks to meet the requirements of the most demanding applications.
HAND-DRIVE NAILS
Common Ring Shank Types 304 and 316 stainless steel, page 42
COLLATED NAILS
20-22 Plastic Strip, Full Round Checkered Head, kered Ring Shank Types 304 and 316 stainless steel and silicone bronze, page 52 20-22 Plastic Strip, p, Full Round Smooth Head, oth Screw Shank Types 304 and 316 stainless steel, page 53 20-22 Plastic Strip, rip, Checkered Casing Head, g Ring Shank Type 304 stainless steel, page 53
Common Smooth Shank Types 304 and 316 stainless steel, page 43
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
Post and Beam, Ring Shank Types 304 and 316 stainless steel, page 44
31-34 Plastic Strip, , Full Round Checkered ed Head, Ring Shank Types 304 and 316 stainless steel, page 55 31-34 Paper Tape, Clipped Smooth Head, Ring Shank Types 304 and 316 stainless steel, page 55
Box, Ring Shank Types 304 and 316 stainless steel, page 45
20-22 Plastic Strip, Full Round Smooth Head, th Smooth Shank Types 304 and 316 stainless steel, page 54
15 Wire Coil, Full Round Checkered Head, Ring Shank Types 304 and 316 stainless steel, page 57
23
HAND-DRIVE SCREWS
Strong-Drive SDS Structural Wood Screw Double-barrier coating, type 316 stainless steel, pages 76-79
24
Strong-Drive SDW Structural Wood Screw Multi-Ply Fastening Washer head, E-Coat coating, pages 80-82
HAND-DRIVE NAILS
Structural Connector Bright, hot-dip galvanized, type 316 stainless steel, page 46
HAND-DRIVE SCREWS
Strong-Drive SD Structural-Connector Screw Class 55 mechanically galvanized, pages 83-84
Strong-Drive SDS Structural Wood Screw Double-barrier coating, type 316 stainless steel, pages 76-79
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
COLLATED NAILS
Paper Tape 33, Ring Shank, , Structural Connector Type 316 stainless steel, page 56
25
COLLATED NAILS
20 Adhesive Collation, ation, T-Style Head Angle Finishing 16 gauge, types 304 and 316 stainless steel, page 63 33 Tape Collation, n, DA-Style Head Angle Finishing 15 gauge, types 304 and 316 stainless steel, page 62 25 Adhesive Collation, ation, FN-Style Head Angle Finishing 15 gauge, types 304 and 316 stainless steel, page 62 16-Gauge Straight, Adhesive Collation n T-Style Head Finishing Types 304 and 316 stainless steel, page 63
18-Gauge Straight, Adhesive Collation,T-Style Head Brads Types 304 and 316 stainless steel, page 64
Types 305 and 316 stainless steel, page 87 Painted head, types 305 and 316 stainless steel, pages 88-89
COLLATED STAPLES
18 Gauge, 14" Crown Types 304 and 316 nd stainless steel, eel, page 67
Hardwood Decking Flat and trim head styles, types 305 and 316 stainless steel, pages 96-97
26
HAND-DRIVE SCREWS
Adhesive Collation Straight, Headless Micro-Pins 23 gauge, type 304 stainless steel, page 64
Fastening to Metal
We offer a wide assortment of stainless steel, self-drilling screws to tackle almost any application. From installing various materials onto steel to fastening the members themselves, our screws pass quality tests to ensure performance in the most demanding applications.
Wafer Head with Wings, Wood Panels to Steel Studs Type 410 stainless steel, page 110
Modified Truss Head, Wire Lathe Type 410 stainless steel, page 107
Hex Washer Head Types 305 and 316 stainless steel and Marutex, page 111
Pancake Head, Standing-Seam Roofing Clips Type 410 stainless steel, page 107
Bugle Head, Wood Panels to Steel Studs Type 410 stainless steel, page 109
27
Fencing
There are lots of ways to build a fence, but regardless of which style is chosen, Simpson Strong-Tie has the right fastener for the job. Whether the fence will be painted or left to weather to a natural color, stainless-steel fasteners not only provide the best alternative for long-term strength, they also preserve the beauty of the fencing material by preventing unsightly rust stains. Type 316 stainless steel is always recommended for coastal environments.
HAND-DRIVE NAILS
Fencing Types 304 and 316 stainless steel, page 48
COLLATED NAILS
20-22 Plastic Strip, Full Round Checkered Head, d, Ring Shank Types 304 and 316 stainless steel, page 52
HAND-DRIVE SCREWS
Trim-Head Decking Coated, page 86 28 Wire Weld, Clipped Head, Ring Shank Type 304 stainless steel, page 56 15 Wire Coil, Full Round Checkered Head, Ring Shank (0.090" dia.) Types 304 and 316 stainless steel, page 58
Types 305 and 316 stainless steel, page 87 Painted head, types 305 and 316 stainless steel, pages 88-89
Bugle-Head Wood Decking Types 305 and 316 stainless steel, pages 90-92 Painted head, type 305 stainless steel, page 92
31-34 Plastic Strip, Full Round Checkered Head, d, Ring Shank Types 304 and 316 stainless steel, page 55
0 Inserted Plastic Coil, Full Round Checkered Head, Ring Shank Type 304 stainless steel, page 61
28
Cooling Towers
Simpson Strong-Tie stocks a wide variety of fasteners for the construction of new cooling towers as well as the maintenance and repair of older towers. Whether for siding, fan decks, or wood construction we have the fasteners you need in 300 series stainless steel as well as aluminum, copper and silicone bronze. By combining on-hand inventory with customer-focused service we are well prepared to supply this fast-moving market.
HAND-DRIVE NAILS
Common Ring Shank Types 304 and 316 stainless steel, page 42
HAND-DRIVE SCREWS
Bugle-Head Wood Decking Types 305 and 316 stainless steel, pages 90-92
MISCELLANEOUS FASTENERS
Fencing Staples Type 304 stainless steel, page 50
Common Spiral Shank (Special-Order Option) Types 304 and 316 stainless steel, page 42
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
Trim Head, Sealing Washer Type 305 stainless steel, page 102
Box, Ring Shank Types 304 and 316 stainless steel, page 45
Hex Washer Head Marutex and types 305 and 316 stainless steel, page 101
Box, Spiral Shank (Special-Order Option) Types 304 and 316 stainless steel, special order option, page 45 Hex Washer Head, Sealing Washer Types 305 and 316 stainless steel, page 101 Sealing Washer Types 302 and 316 stainless steel, page 50
Roofing, Tile and Slating Types 304 and 316 stainless steel, copper and aluminum, pages 38-41
29
HAND-DRIVE NAILS
Stainless-steel nails offer the promise of longevity in corrosive environments; a premium upgrade to ensure that fasteners will last as long as the materials they fasten.
Simpson Strong-Tie offers the widest selection of stainless-steel hand-drive nails in the industry. A vast range of sizes suited to specific applications Many styles available in both types 304 and 316 stainless steel for corrosion resistance tailored to the project environment Checkered or smooth heads as well as smooth, ring and screw shanks Copper, silicone bronze and Monel nails as well as painted-head options and even custom-order nail capability ensures we have, or can make, the fastener you need
30
HAND-DRIVE NAILS
Cedar and Redwood Decking Nails
FEATURES:
Smaller heads are less visible Checker pattern on heads blends with wood grain and reduces glare from sunlight Annular ring shank increases pull-out resistance to help prevent nail heads from popping up over time. Slender shank permits nailing at board ends with reduced splitting Diamond point for easier driving Available in 3 colors: Gray, Redwood and Tan Choose type 316 for seaside applications and superior corrosion resistance
Available in 3 colors
Gray
Redwood
Tan
Length (in.) 2 12 2 2 2 12 2 2 3 3 3 3 3 14 3 14 3 14 3 14 3 2 3 12 3 12 3 12
1 1 1
Gauge 12 12 12 12 12 12 12 12 12 12 12 12 11 11 11 11
Shank Diameter (in.) 0.109 0.109 0.109 0.109 0.109 0.109 0.109 0.109 0.109 0.109 0.109 0.109 0.120 0.120 0.120 0.120
Color Gray Redwood Tan Gray Redwood Tan Gray Redwood Tan Gray Redwood Tan
Approx. Count per lb. 145 145 145 145 120 120 120 120 110 110 110 110 88 88 88 88
1 lb. Model No. S8CRD1 S8CRDG1 S8CRDR1 S8CRDT1 S10CRD1 S10CRDG1 S10CRDR1 S10CRDT1 S12CRD1 S12CRDG1 S12CRDR1 S12CRDT1 S16CRD1 S16CRDG1 S16CRDR1 S16CRDT1
5 lb. Model No. S8CRD5 S8CRDG5 S8CRDR5 S8CRDT5 S10CRD5 S10CRDG5 S10CRDR5 S10CRDT5 S12CRD5 S12CRDG5 S12CRDR5 S12CRDT5 S16CRD5 S16CRDG5 S16CRDR5 S16CRDT5
25 lb. Bucket Model No. S8CRDB S8CRDGB S8CRDRB S8CRDTB S10CRDB S10CRDGB S10CRDRB S10CRDTB S12CRDB S12CRDGB S12CRDRB S12CRDTB S16CRDB S16CRDGB S16CRDRB S16CRDTB
32 32 32 32 32 32 32 32 32 32 32 32 4 4 4 4
7 7
1 1 1 1
Gauge 12 12 12 12 12 12 12 12 12 12 12 12 11 11 11 11
Shank Diameter (in.) 0.109 0.109 0.109 0.109 0.109 0.109 0.109 0.109 0.109 0.109 0.109 0.109 0.120 0.120 0.120 0.120
Color Gray Redwood Tan Gray Redwood Tan Gray Redwood Tan Gray Redwood Tan
Approx. Count per lb. 145 145 145 145 120 120 120 120 110 110 110 110 88 88 88 88
1 lb. Model No. T8CRD1 T8CRDG1 T8CRDR1 T8CRDT1 T10CRD1 T10CRDG1 T10CRDR1 T10CRDT1 T12CRD1 T12CRDG1 T12CRDR1 T12CRDT1 T16CRD1 T16CRDG1 T16CRDR1 T16CRDT1
5 lb. Model No. T8CRD5 T8CRDG5 T8CRDR5 T8CRDT5 T10CRD5 T10CRDG5 T10CRDR5 T10CRDT5 T12CRD5 T12CRDG5 T12CRDR5 T12CRDT5 T16CRD5 T16CRDG5 T16CRDR5 T16CRDT5
25 lb. Bucket Model No. T8CRDB T8CRDGB T8CRDRB T8CRDTB T10CRDB T10CRDGB T10CRDRB T10CRDTB T12CRDB T12CRDGB T12CRDRB T12CRDTB T16CRDB T16CRDGB T16CRDRB T16CRDTB 31
32 32 32 32 32 32 32 32 32 32 32 32 4 4 4 4
7 7 7
1 1 1 1
HAND-DRIVE NAILS
Preservative-Treated Wood Decking Nails
FEATURES:
Ideal for decks and docks Checker pattern on heads blends with wood grain and reduces glare from sunlight Annular ring shank increases pull-out resistance to help prevent nail heads from popping up over time. Larger shank diameter easily penetrates both green and seasoned preservative-treated pine Diamond point for easier driving Choose type 316 for seaside applications and superior corrosion resistance
Gauge 11 10 10 9 9 9 8 8 6
Shank Diameter (in.) 0.120 0.134 0.134 0.148 0.148 0.148 0.165 0.165 0.203
1 lb. Model No. S8PTD1 S8HPTD1 S10PTD1 S10HPTD1 S12PTD1 S16PTD1 S16HPTD1 S20PTD1 S20HPTD1
5 lb. Model No. S8PTD5 S8HPTD5 S10PTD5 S10HPTD5 S12PTD5 S16PTD5 S16HPTD5 S20PTD5 S20HPTD5
25 lb. Bucket Model No. S8PTDB S8HPTDB S10PTDB S10HPTDB S12PTDB S16PTDB S16HPTDB S20PTDB S20HPTDB
32 32 32 16 16 16 32 32
5 5 5
11 11 7
16
Gauge 11 10 10 9 9 9 8 8 6
Shank Diameter (in.) 0.120 0.134 0.134 0.148 0.148 0.148 0.165 0.165 0.203
1 lb. Model No. T8PTD1 T8HPTD1 T10PTD1 T10HPTD1 T12PTD1 T16PTD1 T16HPTD1 T20PTD1 T20HPTD1
5 lb. Model No. T8PTD5 T8HPTD5 T10PTD5 T10HPTD5 T12PTD5 T16PTD5 T16HPTD5 T20PTD5 T20HPTD5
25 lb. Bucket Model No. T8PTDB T8HPTDB T10PTDB T10HPTDB T12PTDB T16PTDB T16HPTDB T20PTDB T20HPTDB
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
32 32 32 16 16 16 32 32
5 5 5
11 11 7
16
32
HAND-DRIVE NAILS
Cedar and Redwood Siding Nails
FEATURES:
Checker pattern on heads blends with wood grain, reduces glare from sunlight and accepts surface nishes Annular ring shank increases pull-out resistance to provide a secure attachment that reduces cupping of siding boards Diamond point for easier driving Choose type 316 for seaside applications and superior corrosion resistance
Gauge 14 14 14 13 13 13 12 12 11 10
Shank Diameter (in.) 0.083 0.083 0.083 0.095 0.095 0.095 0.109 0.109 0.120 0.134
Approx. Count per lb. 495 398 354 245 215 196 120 110 88 74
1 lb. Model No. S3SND1 S4SND1 S5SND1 S6SND1 S7SND1 S8SND1 S10SND1 S12SND1 S16SND1 S20SND1
5 lb. Model No. S3SND5 S4SND5 S5SND5 S6SND5 S7SND5 S8SND5 S10SND5 S12SND5 S16SND5 S20SND5
25 lb. Bucket Model No. S3SNDB S4SNDB S5SNDB S6SNDB S7SNDB S8SNDB S10SNDB S12SNDB S16SNDB S20SNDB
32 32 32 32 32 32
7 7
32 32 4 4
1 1
Gauge 14 14 14 13 13 13 12 12 11 10
Shank Diameter (in.) 0.083 0.083 0.083 0.095 0.095 0.095 0.109 0.109 0.120 0.134
Approx. Count per lb. 495 398 354 245 215 196 120 110 88 74
1 lb. Model No. T3SND1 T4SND1 T5SND1 T6SND1 T7SND1 T8SND1 T10SND1 T12SND1 T16SND1 T20SND1
5 lb. Model No. T3SND5 T4SND5 T5SND5 T6SND5 T7SND5 T8SND5 T10SND5 T12SND5 T16SND5 T20SND5
25 lb. Bucket Model No. T3SNDB T4SNDB T5SNDB T6SNDB T7SNDB T8SNDB T10SNDB T12SNDB T16SNDB T20SNDB
32 32 32 32 32 32
7 7
32 32 4 4
1 1
33
HAND-DRIVE NAILS
Shake and Shingle Siding / Roong Nails
FEATURES:
732" diameter at head provides ample bearing surface to rmly secure shakes and shingles of all types Checker pattern on heads blends with wood grain, reduces glare from sunlight and accepts surface nishes Annular ring shank increases pull-out resistance to provide a secure attachment that helps reduces cupping of siding boards Slender shanks minimize splitting Diamond point for easier driving Choose type 316 for seaside applications and superior corrosion resistance
Gauge 14 14 14 13 13 13
Approx. Count per lb. 470 394 337 237 216 196
25 lb. Bucket Model No. S3SN7B S4SN7B S5SN7B S6SN7B S7SN7B S8SN7B
32 32 32 32 32 32
Gauge 14 14 14 13 13 13
Approx. Count per lb. 470 394 337 237 216 196
25 lb. Bucket Model No. T3SN7B T4SN7B T5SN7B T6SN7B T7SN7B T8SN7B
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
32 32 32 32 32 32
34
HAND-DRIVE NAILS
Painted Siding Nails
FEATURES:
Premium-quality nails for cedar, redwood and cypress siding materials Durable painted nish helps heads blend with siding material Checker pattern on head blends with wood texture Annular ring shank increases pull-out resistance to provide a secure attachment that reduces cupping of siding boards Slender gauge and diamond point for easier driving Custom colors available upon request (minimums apply) call for details Choose type 316 for seaside applications and superior corrosion resistance
Dark Brown
Gray
Redwood
Sienna
Tan
White
Gauge 13 13 13 13 13 13 13 13 13 13 13 13 12 12 12 12 12 12
Shank Diameter (in.) 0.095 0.095 0.095 0.095 0.095 0.095 0.095 0.095 0.095 0.095 0.095 0.095 0.109 0.109 0.109 0.109 0.109 0.109
Color Dark Brown Gray Redwood Sienna Tan White Dark Brown Gray Redwood Sienna Tan White Dark Brown Gray Redwood Sienna Tan White
Approx. Count per lb. 245 245 245 245 245 245 196 196 196 196 196 196 120 120 120 120 120 120
1 lb. Model No. S6SNDB1 S6SNDG1 S6SNDR1 S6SNDS1 S6SNDT1 S6SNDW1 S8SNDB1 S8SNDG1 S8SNDR1 S8SNDS1 S8SNDT1 S8SNDW1 S10SNDB1 S10SNDG1 S10SNDR1 S10SNDS1 S10SNDT1 S10SNDW1
5 lb. Model No. S6SNDB5 S6SNDG5 S6SNDR5 S6SNDS5 S6SNDT5 S6SNDW5 S8SNDB5 S8SNDG5 S8SNDR5 S8SNDS5 S8SNDT5 S8SNDW5 S10SNDB5 S10SNDG5 S10SNDR5 S10SNDS5 S10SNDT5 S10SNDW5
25 lb. Bucket Model No. S6SNDBB S6SNDGB S6SNDRB S6SNDSB S6SNDTB S6SNDWB S8SNDBB S8SNDGB S8SNDRB S8SNDSB S8SNDTB S8SNDWB S10SNDBB S10SNDGB S10SNDRB S10SNDSB S10SNDTB S10SNDWB
32 32 32 32 32 32 32 32 32 32 32 32
7 7 7 7 7 7
32 32 32 32 32 32
35
HAND-DRIVE NAILS
Painted Siding Nails (cont.)
Type 316 Stainless Steel
Penny Size 6d 6d 6d 6d 6d 6d 8d 8d 8d 8d 8d 8d 10d 10d 10d 10d 10d 10d Length (in.) 2 2 2 2 2 2 212 2 2 212 2 2 212 2 2 3 3 3 3 3 3
1 1 1
Gauge 13 13 13 13 13 13 13 13 13 13 13 13 12 12 12 12 12 12
Shank Diameter (in.) 0.095 0.095 0.095 0.095 0.095 0.095 0.095 0.095 0.095 0.095 0.095 0.095 0.109 0.109 0.109 0.109 0.109 0.109
Color Dark Brown Gray Redwood Sienna Tan White Dark Brown Gray Redwood Sienna Tan White Dark Brown Gray Redwood Sienna Tan White
Approx. Count per lb. 245 245 245 245 245 245 196 196 196 196 196 196 120 120 120 120 120 120
1 lb. Model No. T6SNDB1 T6SNDG1 T6SNDR1 T6SNDS1 T6SNDT1 T6SNDW1 T8SNDB1 T8SNDG1 T8SNDR1 T8SNDS1 T8SNDT1 T8SNDW1 T10SNDB1 T10SNDG1 T10SNDR1 T10SNDS1 T10SNDT1 T10SNDW1
5 lb. Model No. T6SNDB5 T6SNDG5 T6SNDR5 T6SNDS5 T6SNDT5 T6SNDW5 T8SNDB5 T8SNDG5 T8SNDR5 T8SNDS5 T8SNDT5 T8SNDW5 T10SNDB5 T10SNDG5 T10SNDR5 T10SNDS5 T10SNDT5 T10SNDW5
25 lb. Bucket Model No. T6SNDBB T6SNDGB T6SNDRB T6SNDSB T6SNDTB T6SNDWB T8SNDBB T8SNDGB T8SNDRB T8SNDSB T8SNDTB T8SNDWB T10SNDBB T10SNDGB T10SNDRB T10SNDSB T10SNDTB T10SNDWB
32 32 32 32 32 32 32 32 32 32 32 32
7 7 7 7 7 7
32 32 32 32 32 32
FEATURES:
Designed expressly for application of various lap and panel siding materials made of ber-cement composites Checker pattern on heads blends with wood faux grain, reduces glare from sunlight and accepts surface nishes Annular ring shank increases pull-out resistance to provide a secure attachment 1 14" length has an 1132" head for blind-nailing lap siding Diamond point for easier driving Recommended for seaside applications and superior corrosion resistance
32
32 32 32
36
HAND-DRIVE NAILS
Pyramid-Head Nails
FEATURES:
Pyramid style decorative heads are reminiscent of old rose-head nails and lend a rustic look to face-nailed lap, bevel and board and batten siding jobs Annular ring shank increases pull-out resistance to provide a secure attachment Silicon bronze weathers to dark brown color These nails are special-order, non-stock items and are subject to minimum order quantities and longer lead times. Call Simpson Strong-Tie for details.
Silicon Bronze
Penny Size 6d 8d 10d 16d Length (in.) 2 212 3 3 2
1
Gauge 11 11 11 11
4 4 4 4
Gauge 11 11 11 11
4 4 4 4
Overlap 1 1 1 8 112 1 2
1 1
Nail Count Factor Linear Foot 0.75 0.75 0.75 0.75 0.75
Nail Count Factor Square Foot 3.60 2.03 1.43 1.13 0.90
How To Figure: Multiply the linear feet or square feet by the nail count factor above. The result is the quantity of nails required. One (1) nail per stud 16" on center Allowance for waste and loss should be added
37
HAND-DRIVE NAILS
Roong, Tile and Slating Nails
FEATURES:
Available in copper, aluminum and stainless steel Large, at head provides extra bearing surface to rmly secure roong material Annular ring shank increases pull-out resistance to provide a secure attachment to wood members and plywood roof decks For slate roofs, determine the correct nail length by doubling the slate thickness and adding one inch Longer lengths ideal for installing curved Spanish roof tiles and thicker slate Aluminum nails also available with a screw shank, call Simpson Strong-Tie for details
Gauge 10 10 10 11 10 11 10 11 10 11 10 10
Shank Diameter (in.) 0.134 0.134 0.134 0.120 0.134 0.120 0.134 0.120 0.134 0.120 0.134 0.134
Approx. Count per lb. 281 212 166 199 139 170 126 149 105 136 91 78
1 lb. Model No. S7510ARN1 S210ARN1 S310ARN1 S311ARN1 S410ARN1 S411ARN1 S510ARN1 S511ARN1 S610ARN1 S611ARN1 S810ARN1 S1010ARN1
5 lb. Model No. S7510ARN5 S210ARN5 S310ARN5 S311ARN5 S410ARN5 S411ARN5 S510ARN5 S511ARN5 S610ARN5 S611ARN5 S810ARN5 S1010ARN5
25 lb. Bucket Model No. S7510ARNB S210ARNB S310ARNB S311ARNB S410ARNB S411ARNB S510ARNB S511ARNB S610ARNB S611ARNB S810ARNB S1010ARNB
8 8 8
32 8
3 11
32 8
3 11
32 8
3 11
32 8 8
3 3
Length (in.)
3
Gauge 10 10 10 11 10 11 10 11 10 11 10 10
Shank Diameter (in.) 0.134 0.134 0.134 0.120 0.134 0.120 0.134 0.120 0.134 0.120 0.134 0.134
Approx. Count per lb. 281 212 166 199 139 170 126 149 105 136 91 78
1 lb. Model No. T7510ARN1 T210ARN1 T310ARN1 T311ARN1 T410ARN1 T411ARN1 T510ARN1 T511ARN1 T610ARN1 T611ARN1 T810ARN1 T1010ARN1
5 lb. Model No. T7510ARN5 T210ARN5 T310ARN5 T311ARN5 T410ARN5 T411ARN5 T510ARN5 T511ARN5 T610ARN5 T611ARN5 T810ARN5 T1010ARN5
25 lb. Bucket Model No. T7510ARNB T210ARNB T310ARNB T311ARNB T410ARNB T411ARNB T510ARNB T511ARNB T610ARNB T611ARNB T810ARNB T1010ARNB
8 8 8
32 8
3 11
32 8
3 11
32 8
3 11
32 8 8
3 3
38
HAND-DRIVE NAILS
Roong, Tile and Slating Nails (cont.)
Tile/Slate, Annular Ring Shank, Type 304 Stainless Steel
These nails are special-order, non-stock items and are subject to minimum order quantities and longer lead times. Call Simpson Strong-Tie for details.
Penny Size 10d 16d 16d 20d 40d 50d 60d Length (in.) 3 3 2 312 4 5 5 2 6
1 1
Gauge 9 10 9 9 8 8 8
Shank Diameter (in.) 0.148 0.134 0.148 0.148 0.165 0.165 0.165
5 lb. Model No. S10ATN5 S16ATN5 S16HATN5 S20ATN5 S40ATN5 S50ATN5 S60ATN5
25 lb. Bucket Model No. S10ATNB S16ATNB S16HATNB S20ATNB S40ATNB S50ATNB S60ATNB
32
16 32 32 2 2 2
15 15
1 1 1
Gauge 9 10 9 9 8 8 8
Shank Diameter (in.) 0.148 0.134 0.148 0.148 0.165 0.165 0.165
5 lb. Model No. S10TN5 S16TN5 S16HTN5 S20TN5 S40TN5 S50TN5 S60TN5
25 lb. Bucket Model No. S10TNB S16TNB S16HTNB S20TNB S40TNB S50TNB S60TNB
32
16 32 32 2 2 2
15 15
1 1 1
Gauge 11 10 11 10 11 10 11 10 11 10 11 10 11 10
Shank Diameter (in.) .120 .134 .120 .134 .120 .134 .120 .134 .120 .134 .120 .134 .120 .134
Approx. Count per lb. 302 187 229 147 187 123 155 112 139 93 124 81 108 67
1 lb. Model No. C7511ARN1 C210ARN1 C211ARN1 C310ARN1 C311ARN1 C410ARN1 C411ARN1 C510ARN1 C511ARN1 C610ARN1 C611ARN1 C810ARN1 C811ARN1 C1010ARN1
5 lb. Model No. C7511ARN5 C210ARN5 C211ARN5 C310ARN5 C311ARN5 C410ARN5 C411ARN5 C510ARN5 C511ARN5 C610ARN5 C611ARN5 C810ARN5 C811ARN5 C1010ARN5
25 lb. Bucket Model No. C7511ARNB C210ARNB C211ARNB C310ARNB C311ARNB C410ARNB C411ARNB C510ARNB C511ARNB C610ARNB C611ARNB C810ARNB C811ARNB C1010ARNB 39
16 8
3 7
16 8
3 7
16 8
3 7
16 8
3 7
16 8
3 7
16 8
3 7
16
HAND-DRIVE NAILS
Roong, Tile and Slating Nails (cont.)
Smooth Shank, Copper
Penny Size 2d 2d 3d 3d 4d 4d 5d 5d 6d 6d 8d 8d 10d Length (in.)
3
Gauge 11 10 11 10 11 10 11 10 11 10 11 10 11 10
Shank Diameter (in.) 0.120 0.134 0.120 0.134 0.120 0.134 0.120 0.134 0.120 0.134 0.120 0.134 0.120 0.134
Approx. Count per lb. 302 187 229 147 187 123 155 112 139 93 124 81 108 67
1 lb. Model No. C7511RN1 C210RN1 C211RN1 C310RN1 C311RN1 C410RN1 C411RN1 C510RN1 C511RN1 C610RN1 C611RN1 C810RN1 C811RN1 C1010RN1
5 lb. Model No. C7511RN5 C210RN5 C211RN5 C310RN5 C311RN5 C410RN5 C411RN5 C510RN5 C511RN5 C610RN5 C611RN5 C810RN5 C811RN5 C1010RN5
25 lb. Bucket Model No. C7511RNB C210RNB C211RNB C310RNB C311RNB C410RNB C411RNB C510RNB C511RNB C610RNB C611RNB C810RNB C811RNB C1010RNB
16 8
3 7
16 8
3 7
16 8
3 7
16 8
3 7
16 8
3 7
16 8
3 7
16
Gauge 9 10 9 9 8 8 8
Shank Diameter (in.) 0.148 0.134 0.148 0.148 0.165 0.165 0.165
5 lb. Model No. C10ATN5 C16ATN5 C16HATN5 C20ATN5 C40ATN5 C50ATN5 C60ATN5
32
16 32 32 2 2 2
15 15
1 1 1
5 lb. Model No. C10TN5 C16TN5 C16HTN5 C20TN5 C40TN5 C50TN5 C60TN5
25 lb. Bucket Model No. C10TNB C16TNB C16HTNB C20TNB C40TNB C50TNB C60TNB
32
16 32 32 2 2 2
15 15
1 1 1
40
HAND-DRIVE NAILS
Roong, Tile and Slating Nails (cont.)
Annular Ring Shank, Aluminum
These nails are special-order, non-stock items and are subject to minimum order quantities and longer lead times. Call Simpson Strong-Tie for details.
Penny Size 2d 3d 4d 3d 4d 6d Length (in.) 1 114 1 2 114 112 2
1
Gauge 11 11 11 9 9 9
Approx. Count per lb. 810 686 577 440 374 288
25 lb. Bucket Model No. A211ARNB A311ARNB A411ARNB A39ARNB A49ARNB A69ARNB
8 8 8
16 16 16
Gauge 11 11 11 9 9 9
Approx. Count per lb. 810 686 577 440 374 288
25 lb. Bucket Model No. A211RNB A311RNB A411RNB A39RNB A49RNB A69RNB
8 8 8
16 16 16
FEATURES:
Heavy EPDM washer provides a weather-proof seal (916" O.D. x 18" thick) Recommended fastener for installation of corrugated-panel roong as well as sheet-metal roong and siding in corrosive environments Annular ring shank increases pull-out resistance to provide a secure attachment to wood members These nails are special-order, non-stock items and are subject to minimum order quantities and longer lead times. Call Simpson Strong-Tie for details.
Gauge 10 10 10 10 10 10 10 10 10
Shank Diameter (in.) 0.134 0.134 0.134 0.134 0.134 0.134 0.134 0.134 0.134
5 lb. Model No. S10125RNW5 S10150RNW5 S10175RNW5 S10200RNW5 S10225RNW5 S10250RNW5 S10300RNW5 S10350RNW5 S10400RNW5
25 lb. Bucket Model No. S10125RNWB S10150RNWB S10175RNWB S10200RNWB S10225RNWB S10250RNWB S10300RNWB S10350RNWB S10400RNWB 41
8 8 8 8 8 8 8 8 8
3 3 3 3
HAND-DRIVE NAILS
Common Nails
FEATURES:
Annular ring shank increases pull-out resistance to provide a secure attachment Stainless-steel nails are recommended for construction of permanent wood foundations by the ANSI/AF&PA Permanent Wood Foundations Design Specications Choose type 316 stainless steel for seaside applications and superior corrosion resistance Special Order Options Call Simpson Strong-Tie for details Spiral shank common, post-and-beam and box nails Silicon-bronze nails Monel nails: Monel is a nickel/copper alloy formulated for optimum service life in salt-water applications. It is required by the Coast Guard for refastening wooden boats in commercial service.
Gauge 15 14 12 12 11 11 10 9 9 8 6 6 6 4 4
Shank Diameter (in.) 0.072 0.083 0.109 0.109 0.120 0.120 0.134 0.148 0.148 0.165 0.203 0.203 0.203 0.238 0.238
Approx. Count per lb. 807 473 228 193 144 133 94 67 60 44 25 22 19 12 10
1 lb. Model No. S2ACN1 S3ACN1 S4ACN1 S5ACN1 S6ACN1 S7ACN1 S8ACN1 S10ACN1 S12ACN1 S16ACN1 S20ACN1 S30ACN1 S40ACN1 S60ACN1 S70ACN1
5 lb. Model No. S2ACN5 S3ACN5 S4ACN5 S5ACN5 S6ACN5 S7ACN5 S8ACN5 S10ACN5 S12ACN5 S16ACN5 S20ACN5 S30ACN5 S40ACN5 S60ACN5 S70ACN5
25 lb. Bucket Model No. S2ACNB S3ACNB S4ACNB S5ACNB S6ACNB S7ACNB S8ACNB S10ACNB S12ACNB S16ACNB S20ACNB S30ACNB S40ACNB S60ACNB S70ACNB
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
16 4 4
32
1 1 17 17 9
64 64
32 16 16 32
5 5
11 7 7 7
16 16 16 32 32
15 15
Gauge 15 14 12 12 11 11 10 9 9 8 6 6 6 4 4
Shank Diameter (in.) 0.072 0.083 0.109 0.109 0.120 0.120 0.134 0.148 0.148 0.165 0.203 0.203 0.203 0.238 0.238
Approx. Count per lb. 807 473 228 193 144 133 94 67 60 44 25 22 19 12 10
1 lb. Model No. T2ACN1 T3ACN1 T4ACN1 T5ACN1 T6ACN1 T7ACN1 T8ACN1 T10ACN1 T12ACN1 T16ACN1 T20ACN1 T30ACN1 T40ACN1 T60ACN1 T70ACN1
5 lb. Model No. T2ACN5 T3ACN5 T4ACN5 T5ACN5 T6ACN5 T7ACN5 T8ACN5 T10ACN5 T12ACN5 T16ACN5 T20ACN5 T30ACN5 T40ACN5 T60ACN5 T70ACN5
25 lb. Bucket Model No. T2ACNB T3ACNB T4ACNB T5ACNB T6ACNB T7ACNB T8ACNB T10ACNB T12ACNB T16ACNB T20ACNB T30ACNB T40ACNB T60ACNB T70ACNB
16 4 4
32
1 1 17 17 9
64 64
32 16 16 32
5 5
11 7 7 7
16 16 16 32 32
15 15
HAND-DRIVE NAILS
Common Nails (cont.)
Common, Smooth Shank, Type 304 Stainless Steel
Penny Size 2d 3d 4d 5d 6d 7d 8d 10d 12d 16d 20d 30d 40d 60d 70d Length (in.) 1 114 112 1 4 2 214 212 3 3 4 312 4 412 5 6 7
1 3
Gauge 15 14 12 12 11 11 10 9 9 8 6 6 6 4 4
Shank Diameter (in.) 0.072 0.083 0.109 0.109 0.120 0.120 0.134 0.148 0.148 0.165 0.203 0.203 0.203 0.238 0.238
Approx. Count per lb. 807 473 228 193 144 133 94 67 60 44 25 22 19 12 10
1 lb. Model No. S2CN1 S3CN1 S4CN1 S5CN1 S6CN1 S7CN1 S8CN1 S10CN1 S12CN1 S16CN1 S20CN1 S30CN1 S40CN1 S60CN1 S70CN1
5 lb. Model No. S2CN5 S3CN5 S4CN5 S5CN5 S6CN5 S7CN5 S8CN5 S10CN5 S12CN5 S16CN5 S20CN5 S30CN5 S40CN5 S60CN5 S70CN5
25 lb. Bucket Model No. S2CNB S3CNB S4CNB S5CNB S6CNB S7CNB S8CNB S10CNB S12CNB S16CNB S20CNB S30CNB S40CNB S60CNB S70CNB
16
32 4 4
1 1 17 17 9
64 64
32 16 16 32
5 5
11 7 7 7
16 16 16 32 32
15 15
Gauge 15 14 12 12 11 11 10 9 9 8 6 6 6 4 4
Shank Diameter (in.) 0.072 0.083 0.109 0.109 0.120 0.120 0.134 0.148 0.148 0.165 0.203 0.203 0.203 0.238 0.238
Approx. Count per lb. 807 473 228 193 144 133 94 67 60 44 25 22 19 12 10
1 lb. Model No. T2CN1 T3CN1 T4CN1 T5CN1 T6CN1 T7CN1 T8CN1 T10CN1 T12CN1 T16CN1 T20CN1 T30CN1 T40CN1 T60CN1 T70CN1
5 lb. Model No. T2CN5 T3CN5 T4CN5 T5CN5 T6CN5 T7CN5 T8CN5 T10CN5 T12CN5 T16CN5 T20CN5 T30CN5 T40CN5 T60CN5 T70CN5
25 lb. Bucket Model No. T2CNB T3CNB T4CNB T5CNB T6CNB T7CNB T8CNB T10CNB T12CNB T16CNB T20CNB T30CNB T40CNB T60CNB T70CNB
16
32 4 4
1 1 17 17 9
64 64
32 16 16 32
5 5
11 7 7 7
16 16 16 32 32
15 15
43
HAND-DRIVE NAILS
Post and Beam Nails
FEATURES:
Checker pattern on heads blends with wood grain, reduces glare from sunlight and accepts surface nishes Annular ring shank increases pull-out resistance to provide a secure attachment Stainless-steel nails are recommended for construction of permanent wood foundations by the ANSI/AF&PA Permanent Wood Foundations Design Specications Choose type 316 stainless steel for seaside applications and superior corrosion resistance Special Order Options Call Simpson Strong-Tie for details Spiral shank common, post-and-beam and box nails Silicon-bronze nails Monel nails: Monel is a nickel/copper alloy formulated for optimum service life in salt-water applications. It is required by the Coast Guard for refastening wooden boats in commercial service.
Post and Beam, Annular Ring Shank, Type 304 Stainless Steel
Penny Size 6d 8d 10d 12d 16d 20d 30d 40d 60d 70d Length (in.) 2 212 3 314 312 4 412 5 6 7 Gauge 12 11 10 10 9 8 8 8 6 4 Shank Diameter (in.) 0.109 0.120 0.134 0.134 0.148 0.165 0.165 0.165 0.203 0.238" Head Diameter (in.)
17 17 9 9
1 lb. Model No. S6APB1 S8APB1 S10APB1 S12APB1 S16APB1 S20APB1 S30APB1 S40APB1 S60APB1 S70APB1
5 lb. Model No. S6APB5 S8APB5 S10APB5 S12APB5 S16APB5 S20APB5 S30APB5 S40APB5 S60APB5 S70APB5
25 lb. Bucket Model No. S6APBB S8APBB S10APBB S12APBB S16APBB S20APBB S30APBB S40APBB S60APBB S70APBB
64 64
32 32 16 32 32 32
11 11 11 7
32 32
15
Post and Beam, Annular Ring Shank, Type 316 Stainless Steel
Penny Size 6d 8d 10d 12d 16d 20d 30d 40d 60d 70d Length (in.) 2 212 3 314 312 4 412 5 6 7 Gauge 12 11 10 10 9 8 8 8 6 4 1 lb. Model No. T6APB1 T8APB1 T10APB1 T12APB1 T16APB1 T20APB1 T30APB1 T40APB1 T60APB1 T70APB1 5 lb. Model No. T6APB5 T8APB5 T10APB5 T12APB5 T16APB5 T20APB5 T30APB5 T40APB5 T60APB5 T70APB5 25 lb. Bucket Model No. T6APBB T8APBB T10APBB T12APBB T16APBB T20APBB T30APBB T40APBB T60APBB T70APBB
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
Shank Diameter (in.) 0.109 0.120 0.134 0.134 0.148 0.165 0.165 0.165 0.203 0.238"
64 64
32 32 16 32 32 32
11 11 11 7
32 32
15
44
HAND-DRIVE NAILS
Box Nails
FEATURES:
Checker pattern on heads blends with wood grain, reduces glare from sunlight and accepts surface nishes Annular ring shank increases pull-out resistance to provide a secure attachment Stainless-steel nails are recommended for construction of permanent wood foundations by the ANSI/AF&PA Permanent Wood Foundations Design Specications Choose type 316 stainless steel for seaside applications and superior corrosion resistance Special Order Options Call Simpson Strong-Tie for details Spiral shank common, post-and-beam and box nails Silicon-bronze nails Monel nails: Monel is a nickel/copper alloy formulated for optimum service life in salt-water applications. It is required by the Coast Guard for refastening wooden boats in commercial service.
Gauge 14 14 13 12 12 12 11 10 10 8
Shank Diameter (in.) 0.083 0.083 0.095 0.109 0.109 0.109 0.120 0.134 0.134 0.165
Approx. Count per lb. 473 413 260 175 153 138 99 72 67 40
1 lb. Model No. S3ABN1 S4ABN1 S5ABN1 S6ABN1 S7ABN1 S8ABN1 S10ABN1 S12ABN1 S16ABN1 S20ABN1
5 lb. Model No. S3ABN5 S4ABN5 S5ABN5 S6ABN5 S7ABN5 S8ABN5 S10ABN5 S12ABN5 S16ABN5 S20ABN5
25 lb. Bucket Model No. S3ABNB S4ABNB S5ABNB S6ABNB S7ABNB S8ABNB S10ABNB S12ABNB S16ABNB S20ABNB
32 32 64
13
17 17 17 17 9 9
64 64 64 64
32 32 32
11
Gauge 14 14 13 12 12 12 11 10 10 8
Shank Diameter (in.) 0.083 0.083 0.095 0.109 0.109 0.109 0.120 0.134 0.134 0.165
Approx. Count per lb. 473 413 260 175 153 138 99 72 67 40
1 lb. Model No. T3ABN1 T4ABN1 T5ABN1 T6ABN1 T7ABN1 T8ABN1 T10ABN1 T12ABN1 T16ABN1 T20ABN1
5 lb. Model No. T3ABN5 T4ABN5 T5ABN5 T6ABN5 T7ABN5 T8ABN5 T10ABN5 T12ABN5 T16ABN5 T20ABN5
25 lb. Bucket Model No. T3ABNB T4ABNB T5ABNB T6ABNB T7ABNB T8ABNB T10ABNB T12ABNB T16ABNB T20ABNB
32 32 64
13
17 17 17 17 9 9
64 64 64 64
32 32 32
11
45
HAND-DRIVE NAILS
Structural-Connector Nails
FEATURES:
Stainless-steel nails are recommended for construction of permanent wood foundations by the ANSI/AF&PA Permanent Wood Foundations Design Specications Choose type 316 stainless steel for seaside applications and superior corrosion resistance
Gauge 8 3 2
1
32 2
Bright nails are not for use in exterior or preservative-treated wood applications.
N54A Nail
16 16 16 32
11
16 16
32 16 32
11
These products are coated fasteners with a medium level of corrosion protection, making them suitable for use in some exterior and corrosive environments and with some preservative-treated woods. For higher exposure applications, consider 300 series stainless-steel fasteners for superior corrosion resistance. See pages 10-13 for addition important information. 46
HAND-DRIVE NAILS
Finishing Nails
FEATURES:
Brad head for a less-visible appearance Smooth shank, diamond point for easier driving Choose type 316 for seaside applications and superior corrosion resistance
Gauge 15 15 14 14 13 12 11 11 11 11
Shank Diameter (in.) 0.072 0.072 0.083 0.083 0.095 0.109 0.120 0.120 0.120 0.120
Head Diameter (in.) 0.109 0.109 0.120 0.120 0.135 0.148 0.165 0.165 0.165 0.201
Approx. Count per lb. 863 649 434 375 247 146 102 97 86 85
1 lb. Model No. S2FN1* S3FN1* S4FN1 S5FN1* S6FN1 S8FN1 S10FN1 S12FN1* S16FN1 S20FN1*
5 lb. Model No. S2FN5* S3FN5* S4FN5 S5FN5* S6FN5 S8FN5 S10FN5 S12FN5* S16FN5 S20FN5*
25 lb. Bucket Model No. S2FNB* S3FNB* S4FNB S5FNB* S6FNB S8FNB S10FNB S12FNB* S16FNB S20FNB*
* These nails are special-order, non-stock items and are subject to minimum order quantities and longer lead times. Call Simpson Strong-Tie for details.
Gauge 15 15 14 14 13 12 11 11 11 11
Shank Diameter (in.) 0.072 0.072 0.083 0.083 0.095 0.109 0.120 0.120 0.120 0.120
Head Diameter (in.) 0.109 0.109 0.120 0.120 0.135 0.148 0.165 0.165 0.165 0.201
Approx. Count per lb. 863 649 434 375 247 146 102 97 86 85
1 lb. Model No. T2FN1* T3FN1* T4FN1 T5FN1* T6FN1 T8FN1 T10FN1 T12FN1* T16FN1 T20FN1*
5 lb. Model No. T2FN5* T3FN5* T4FN5 T5FN5* T6FN5 T8FN5 T10FN5 T12FN5* T16FN5 T20FN5*
25 lb. Bucket Model No. T2FNB* T3FNB* T4FNB T5FNB* T6FNB T8FNB T10FNB T12FNB* T16FNB T20FNB*
* These nails are special-order, non-stock items and are subject to minimum order quantities and longer lead times. Call Simpson Strong-Tie for details.
47
HAND-DRIVE NAILS
Fencing Nails
FEATURES:
Checker pattern on heads blends with wood grain, reduces glare from sunlight and accepts surface nishes Annular ring shank increases pull-out resistance to provide a secure attachment Diamond point for easier driving Choose type 316 for seaside applications to resist streaking on wood or vinyl fences
64 64
64 64
Gauge 10 10 11 10
Model No. 100 count S10A150X0C S10A175X0C S11A175X0C S10A200X0C 1000 count S10A150X0M S10A175X0M S11A175X0M S10A200X0M
Gauge 10
HAND-DRIVE NAILS
Custom-Order Nails
We Make Nails To Your Specication
Simpson Strong-Tie is proud to be one of the last remaining manufacturer of stainless-steel and copper-alloy nails in the United States. While we specialize in AISI-type 304 and 316 stainless steel, aluminum, brass, commercial bronze, copper, monel and silicon bronze, exotic alloys pose no problem provided their mechanical properties are within our manufacturing capabilities. Call Simpson Strong-Tie for details. It may also be helpful to visit www.strongtie.com to download worksheet T-NAIL-WS11 which spells out the needed information.
Simpson Strong-Tie offers fasteners in a variety of stock colors to match popular construction materials such as cedar and redwood lumber, major brands of composite decking and siding/trim material. Custom color matching is also available to match virtually any material. Material samples or a Pantone color number are required and 3-4 week lead times are standard. Call Simpson Strong-Tie for details.
49
Gauge 13 13 10
Hog Rings
Blair Shaped, Type 304 Stainless Steel
Gauge 12 Width Open (in.) 0.95 Width Across (in.) 1.82 Approx. Count per lb. 111 1 lb. Model No. S12131HR1 5 lb. Model No. S12131HR5 25 lb. Bucket Model No. S12131HRB
Blair Shaped
Inside Diameter
Carton Count 100 1000 100 1000 100 1000 100 1000
Model No. Type 302 S10N062SWC S10N062SWM S12N062SWC S12N062SWM S10N112SWC S10N112SWM Type 316 T25N112SWC T25N112SWM
Outside Diameter
8 8 8 8
4 4
50
Combine the short-term benefit of increased fastening efficiency with the long-term benefit of stainless-steel fasteners.
Regardless of the type of tool you have, chances are we have a collated nail or staple to turn it into a stainless-steel fastening machine. A variety of collation types plastic coil and strip, mylar and paper tape, wire welded and coil in a variety of angles Many styles available in both types 304 and 316 stainless steel for corrosion resistance tailored to the project environment All the popular head and shank styles, including painted nails for siding applications Stainless-steel finish nails, brads and staples in all sizes
51
COLLATED NAILS
20-22 Plastic Strip, Full Round Head, Ring-Shank Nails
FEATURES:
2022 collation angle Checker pattern on heads blends with the wood grain, reduces glare from sunlight and accepts surface nishes Annular ring shank increases pull-out resistance to provide a secure attachment Shanks are coated to increase pull-out resistance Choose type 316 for seaside applications and superior corrosion resistance
Model No. Type 304 S12A200CNB S12A200CNJ S11A200CNB S11A200CNJ S9A225CNJ S12A237CNB S12A237CNJ S11A250CNB S11A250CNJ S10A250CNB S11A300CNB S11A300CNJ S10A300CNB S10A300CNJ S11A325CNB S11A325CNJ S10A325CNB S10A325CNJ S10A350CNB S10A350CNJ Type 316 T12A200CNB T12A200CNJ T11A200CNB T11A200CNJ T12A237CNB T12A237CNJ T11A250CNB T11A250CNJ T11A300CNB T11A300CNJ T10A300CNB T10A300CNJ T11A325CNB T11A325CNJ
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
0.113 0.113 0.120 0.120 0.148 0.113 0.113 0.120 0.120 0.134 0.120 0.120 0.134 0.134 0.120 0.120 0.134 0.134 0.134 0.134
9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9
32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32
5000 1000 5000 1000 1000 5000 1000 4000 1000 4000 4000 1000 4000 1000 4000 1000 4000 1000 4000 1000
Silicon Bronze
Shank Head Penny Length Carton Diameter Diameter Size (in.) Quantity (in.) (in.) 8d 8d 12d 12d 212 2 2 314 314
1
9 9 9 9
32 32 32 32
* These nails are special-order, non-stock items and are subject to minimum order quantities and longer lead times. Call Simpson Strong-Tie for details.
52
COLLATED NAILS
20-22 Plastic Strip, Full Round Head, Screw-Shank Nails
FEATURES:
2022 collation angle Smooth head Screw shank increases pull-out resistance to provide a secure attachment Shanks are coated to increase pull-out resistance Choose type 316 for seaside applications and superior corrosion resistance
Model No. Type 304 S12S200CNB S12S200CNJ S12S250CNB S12S250CNJ S11S300CNB S11S300CNJ S11S325CNB S11S325CNJ S10S350CNB S10S350CNJ Type 316 T12S200CNB T12S200CNJ T12S250CNB T12S250CNJ T11S300CNB T11S300CNJ T11S325CNB T11S325CNJ T10S350CNB* T10S350CNJ*
32 32 32 32 32 32 32 32 32 32
5000 1000 4000 1000 4000 1000 4000 1000 4000 1000
* These nails are special-order, non-stock items and are subject to minimum order quantities and longer lead times. Call Simpson Strong-Tie for details.
Brown
Gray
Redwood Sienna
Tan
Color None Brown Gray Redwood Sienna Tan None Brown Gray Redwood Sienna Tan
Carton Quantity 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000
Model No. S11A237KDJ S11A237KJB S11A237KJG S11A237KJR S11A237KJS S11A237KJT S10A325KDJ S10A325KJB S10A325KJG S10A325KJR S10A325KJS S10A325KJT
0.120 0.120 0.120 0.120 0.120 0.120 0.134 0.134 0.134 0.134 0.134 0.134
1 1 1 1 1 1 1 1 1 1 1 1
4 4 4 4 4 4 4 4 4 4 4 4
COLLATED NAILS
20-22 Plastic Strip, Full Round Head, Smooth-Shank Nails
FEATURES:
2022 collation angle Smooth head Shanks are coated to increase pull-out resistance Choose type 316 for seaside applications and superior corrosion resistance
Model No. Type 304 S12N237CNB S12N237CNJ S9N237CNJ S9N300CNJ S8N350CNJ Type 316 T9N150JNJ
32 32 32 32 32 32
SN350-20F (up to 0.148") F21PL D51850 (up to 0.148"), D51844 (up to 0.148") GRTFR83 (up to 0.131", 314"), GRTRH350 (up to 0.148") NR83AS (up to 0.131", 314"), NR90AC3, NR90AEPR (up to 0.148"), NR90GR (up to 0.131"), NR90GR2 (up to 0.131") AN923 SN883RH (up to 0.148", 314"), SN883RH2 (up to 0.148", 314"), SN890RH (up to 0.148")
SN902XP (up to 0.148", 314"), SN952XP (up to 0.148"), GT90FRH (up to 0.131") FramePro 602 (up to 0.148"), FramePro 702XP (up to 0.148"), FramePro 752XP
If you dont see your particular model in the table above, see page 69 or call Simpson Strong-Tie and a sales professional will assist with fastener selection.
54
COLLATED NAILS
3134 Plastic Strip, Full Round Head, Ring-Shank Nails
FEATURES:
3134 collation angle Checker pattern on heads blends with the wood grain, reduces glare from sunlight and accepts surface nishes Annular ring shank increases pull-out resistance to provide a secure attachment Choose type 316 for seaside applications and superior corrosion resistance
Model No. Type 304 S12A237B31* S12A237P31 S11A300B31 S11A300P31 S10A325B31* S10A325P31* Type 316 T12A237B31* T12A237P31* T11A300B31* T11A300P31 T10A325B31* T10A325P31
32 32 32 32 32 32
* These nails are special-order, non-stock items and are subject to minimum order quantities and longer lead times. Call Simpson Strong-Tie for details.
Model No. Type 304 S12A200T31 S12A237T31 S11A300T31 S10A325T31 S10A350T31 Type 316 T12A200T31* T12A237T31 T11A300T31 T10A325T31 T10A350T31*
* These nails are special-order, non-stock items and are subject to minimum order quantities and longer lead times. Call Simpson Strong-Tie for details.
Compatible Pneumatic Tools Collated 3134 Plastic Strip and Paper Tape
Bosch Bostitch DeWalt Grip-Rite Hitachi Makita Max Paslode Porter Cable Ridgid Senco SN350-34C F33PT D51825, D51822 GRTFC83 (up to 314"), GRTCH350 NR83AA3 (up to 314"), NR90ADPR, NR90GC2 AN943 SN883CH/34 (up to 314"), SN890CH/34 PF350S, CF325 (up to 314"), F350S, 900420 (up to 314") FC350A R350CHA SN901XP (up to 314"), SN951XP, GT90CH, FramePro601, FramePro701XP
If you dont see your particular model in the table above, see page 69 or call Simpson Strong-Tie and a sales professional will assist with fastener selection.
55
COLLATED NAILS
28 Wire Weld, Clipped Head, Ring-Shank Nails
FEATURES:
28 collation angle Smooth head Annular ring shank increases pull-out resistance to provide a secure attachment
If you dont see your particular model in the table above, see page 71 or call Simpson Strong-Tie and a sales professional will assist with fastener selection.
32 32
If you dont see your particular model in the table above, see page 69 or call Simpson Strong-Tie and a sales professional will assist with fastener selection.
56
COLLATED NAILS
15 Wire Coil, Full Round Head, Ring-Shank Decking/Framing Nails
FEATURES:
15 collation angle; stainless-steel collation medium Checker pattern on head blends with the wood grain, reduces glare from sunlight and accepts surface nishes. Annular ring shank increases pull-out resistance to help prevent nail heads from popping up over time Choose type 316 for seaside applications and superior corrosion resistance
Shank Diameter (in.) 0.099 0.099 0.099 0.099 0.099 0.113 0.120 0.131 0.120 0.131 0.131
Carton Quantity 3600 3600 3600 1800 3600 3600 1800 1800 1800 1800 1800
Model No. Type 304 S12A150PNB S12A175PNB S12A200PNB S12A250PNB S12A237PNB S11A300PNJ S10A300PNJ S11A325PNJ S10A325PNJ Type 316 T12A200PNB T12A225PNJ T12A250PNB T11A300PNJ T10A300PNJ T11A325PNJ T10A350PNJ
4 4 4 4 4 4
64 64 64 64 64
N80CB (up to 314"), N75C (up to 3"), N89C D51855 P350C/CNW90, P275C (up to 234") GRTCN90-312, GRTCS250 (up to 0.099", 212") NV65AH (up to 0.099", 212"), NV75AG (up to 3"), NV83A2 AN901 CN565S (up to 212", 0.099"), CN565D (up to 212", 0.113"), CN665 (up to 212"), CN890S, CN565 (up to 212", 0.099"), CN100, CN70 (up to 212"), CN80 (up to 314") SCN60XP (up to 234", 0.113"), SCN49 (up to 212", 0.113"), SCN 65XP (up to 0.113"), PalletPro100, PalletPro130 (over 3"), PalletPro70 (up to 234", 0.113"), Pallet Pro83 (up to 314")
Duo-Fast
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
If you dont see your particular model in the table above, see page 70 or call Simpson Strong-Tie and a sales professional will assist with fastener selection.
57
COLLATED NAILS
15 Wire Coil, Full Round Head, Ring-Shank Siding Nails
FEATURES:
15 collation angle Checker pattern on heads blends with wood grain, reduces glare from sunlight and accepts surface nishes Generous under-head llet allows nails to be driven ush, or countersunk, without crushing surrounding wood Annular ring shank increases pull-out resistance to provide a secure attachment that reduces cupping of siding boards Slender gauge and diamond point for easier driving Choose type 316 for seaside applications and superior corrosion resistance
64 64 64 64 64 64
64 64 64 64 64
15 Wire Coil, Full Round Head, Ring Shank, Fiber-Cement Siding Nails
FEATURES:
15 collation angle Checker pattern on head blends with the faux wood grain, reduces glare from sunlight and accepts surface nishes. Annular ring shank increases pull-out resistance to provide a secure attachment
COLLATED NAILS
15 Wire Coil, Full Round Head, Painted Ring-Shank Siding Nails
FEATURES:
15 collation angle Checker pattern on heads blends with wood grain, reduces glare from sunlight and accepts surface nishes Durable painted nish helps heads blend with decking material Annular ring shank increases pull-out resistance to provide a secure attachment that reduces cupping of siding boards Slender gauge and diamond point for easier driving
Dark Brown
Gray
Redwood
Tan
White
Shank Diameter (in.) 0.090 0.090 0.090 0.090 0.090 0.090 0.090 0.090 0.090 0.090 0.090 0.090 0.090 0.090 0.090
Color Dark Brown Gray Redwood Tan White Dark Brown White Gray Redwood Tan Dark Brown Gray Redwood Tan White
Carton Quantity 3600 3600 3600 3600 3600 3600 3600 3600 3600 3600 3600 3600 3600 3600 3600
Model No. S13A200CCB S13A200CCG S13A200CCR S13A200CCT S13A200CWH S13A219SNB S13A219SNW S13A219SNG S13A219SNR S13A219SNT S13A250CCB S13A250CCG S13A250CCR S13A250CCT S13A250CWH
64 64 64 64 64 64 64 64 64 64 64 64 64 64 64
8d 8d 8d
If you dont see your particular model in the table above, see page 70 or call Simpson Strong-Tie and a sales professional will assist with fastener selection.
59
COLLATED NAILS
15 Wire Coil, Full Round Head, Ring-Shank Roong Nails
FEATURES:
15 collation angle Ideal for asphalt and synthetic slate roong Large at head, diamond point for easier driving Annular ring shank increases pull-out resistance to provide a secure attachment to OSB or plywood roof decks Choose type 316 for seaside applications and superior corrosion resistance
Shank Diameter (in.) 0.120 0.120 0.120 0.120 0.120 0.120 0.120
8 8 8 8 8 8 8
8 8 8 8
Penny Size 2d 2d 3d 3d 4d 4d 5d 5d
Length (in.)
3 7
Shank Diameter (in.) 0.120 0.120 0.120 0.120 0.120 0.120 0.120 0.120 0.120 0.120
Carton Quantity 7200 7200 7200 2400 7200 2400 7200 2400 7200 2400
Model No. S11N075RNB S11N087RNB S11N100RNB S11N100RNJ S11N125RNB S11N125RNJ S11N150RNB S11N150RNJ S11N175RNB S11N175RNJ
8 8 8 8 8 8 8 8 8 8
RN175 RN46 D51321 GRTCR175 NV45AB2, NV45AE AN453 CN445R, CN450R R175-C, CR175C
Ridgid Senco
8 8 8 8
If you dont see your particular model in the table above, see page 70 or call Simpson Strong-Tie and a sales professional will assist with fastener selection.
COLLATED NAILS
15 Inserted Plastic Coil, Full Round Head, Ring Shank Nails
FEATURES:
15 collation angle Checker pattern on head blends with the wood grain, reduces glare from sunlight and accepts surface nishes. Annular ring shank increases pull-out resistance to provide a secure attachment Choose type 316 for seaside applications and superior corrosion resistance
Model No. Type 304 S13A150IPC S13A175IPC S13A200IPC S13A225IPC S13A250IPC Type 316 T13A150IPC T13A175IPC T13A200IPC T13A225IPC
13 13 13 13 13
If you dont see your particular model in the table above, call Simpson Strong-Tie and a sales professional will assist with fastener selection.
FEATURES:
Checker pattern on head blends with the wood grain, reduces glare from sunlight and accepts surface nishes. Annular ring shank increases pull-out resistance to provide a secure attachment Available in type 304 and aluminum
Type 304 Stainless Steel and Aluminum for DuoFast Model KDN50
Penny Size 5d 7d Length (in.) 1 4 178 214
3
* These nails are special-order, non-stock items and are subject to minimum order quantities and longer lead times. Call Simpson Strong-Tie for details.
COLLATED NAILS
25 Adhesive Collation, FN-Style Angle Finishing Nails
FEATURES:
25 collation angle T-style head minimizes the nail head size for easier concealment Choose type 316 for seaside applications and superior corrosion resistance
500 count Model No. Type 316 T15N150FNB T15N200FNB T15N250FNB Type 304
If you dont see your particular model in the table above, see page 71 or call Simpson Strong-Tie and a sales professional will assist with fastener selection.
If you dont see your particular model in the table above, see page 71 or call Simpson Strong-Tie and a sales professional will assist with fastener selection. 62
COLLATED NAILS
20 Adhesive Collation, T-Style Head Angle Finishing Nails
FEATURES:
20 collation angle T-style head minimizes the nail head size for easier concealment Choose type 316 for seaside applications and superior corrosion resistance
500-Count Model No. Type 316 T16N125PFB T16N150PFB T16N200PFB T16N250PFB Type 304
If you dont see your particular model in the table above, see page 71 or call Simpson Strong-Tie and a sales professional will assist with fastener selection.
2500-Count Model No. Type 304 S16N150FNJ S16N200FNJ S16N250FNJ Type 316 T16N125FNJ T16N150FNJ T16N200FNJ T16N250FNJ
If you dont see your particular model in the table above, see page 72 or call Simpson Strong-Tie and a sales professional will assist with fastener selection. 63
COLLATED NAILS
18-Gauge Straight, Adhesive Collation, T-Style Head Brads
Choose type 316 for seaside applications and superior corrosion resistance
500 count Model No. Type 316 Quantity 10000 5000 5000 5000 5000 5000 5000 5000 5000
Carton Model No. Type 304 S18N075FNJ S18N125FNJ S18N150FNJ S18N175FNJ S18N200FNJ Type 316 T18N037FNJ T18N050FNJ T18N062FNJ T18N075FNJ T18N100FNJ T18N125FNJ T18N150FNJ T18N175FNJ T18N200FNJ
8 2 4
If you dont see your particular model in the table above, see page 72 or call Simpson Strong-Tie and a sales professional will assist with fastener selection.
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
Carton Count 1000 5000 1000 5000 1000 5000 1000 5000 1000 5000 1000 5000
Model No. S23N050MPB S23N050MPN S23N075MPB S23N075MPN S23N100MPB S23N100MPN S23N119MPB S23N119MPN S23N150MPB S23N150MPN S23N175MPB S23N175MPN
2 2 4 4
3 3
If you dont see your particular model in the table above, see page 73 or call Simpson Strong-Tie and a sales professional will assist with fastener selection.
COLLATED STAPLES
1
Compatible Tools
Bostitch Grip-Rite Hitachi PowerNail Primatech MIIIFS GR200FS N5009AF 445FS, 445FS w/Power Roller P220, P250S, P260
If you dont see your particular model in the table above, see page 73 or call Simpson Strong-Tie and a sales professional will assist with fastener selection.
Length (in.)
3
Model No. Type 304 S16N100N13 S16N125N15 S16N150N17 S16N175N19 S16N200N21 Type 316 T16N075N11 T16N100N13 T16N125N15 T16N150N17 T16N175N19 T16N200N21
1 114 1 2 134 2
1
16 16 16 16
If you dont see your particular model in the table above, see page 73 or call Simpson Strong-Tie and a sales professional will assist with fastener selection.
65
COLLATED STAPLES
1
Model No. Type 304 S16N125GS S16N150GS S16N175GS S16N200GS Type 316 T16N125GS T16N150GS T16N175GS T16N200GS
If you dont see your particular model in the table above, see page 73 or call Simpson Strong-Tie and a sales professional will assist with fastener selection.
If you dont see your particular model in the table above, see page 74 or call Simpson Strong-Tie and a sales professional will assist with fastener selection.
Model No. Type 304 S16N075P51 S16N100P53 S16N125P55 Type 316 T16N075P51 T16N100P53 T16N125P55
1 114
If you dont see your particular model in the table above, see page 74 or call Simpson Strong-Tie and a sales professional will assist with fastener selection. 66
COLLATED STAPLES
1
Model No. Type 304 S18N062L10 S18N100L13 S18N112L14 S18N125L15 S18N150L17 Type 316 T18N062L10 T18N075L11 T18N100L13 T18N112L14 T18N125L15 T18N150L17
8 4
1 1 8 114 112
1
If you dont see your particular model in the table above, see page 74 or call Simpson Strong-Tie and a sales professional will assist with fastener selection.
3
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
8 2
67
COLLATED STAPLES
T Series Flooring Cleats
Ideal for tongue-and-groove decking and ooring
Compatible Tools
Hitachi Primatech NT50AF, NT50AGF, NT50YF P210T, P240T, P250T, H300T, H330T
If you dont see your particular model in the table above, see page 73 or call Simpson Strong-Tie and a sales professional will assist with fastener selection.
Compatible Tools
Bostitch Grip-Rite Hitachi Porter Cable PowerNail MFN200, MFN201, MIIIFN GR200LCN NT50AF FCN200 45, 45R, 445SN, 101SN, 101R, 445, 445 FLEX Power Roller P210L, P240L, P250L, H300L, H330L SHF50, SHF15
Primatech Senco
If you dont see your particular model in the table above, see page 73 or call Simpson Strong-Tie and a sales professional will assist with fastener selection.
68
31-34 PAPER TAPE AND PLASTIC STRIP APACH AN-10034E APACH L3490 ATRO CHS933 BEA D100-934C BESCO CHF 9034 BESCO CHF 9034P BOSCH SN350-34C BOSTITCH F33PT BOSTITCH N90PT-1 CRAFTSMAN 18179 CRAFTSMAN 18189 DEWALT D51822 DEWALT D51823 DEWALT D51825 DUO-FAST CN-325B DUO-FAST NSPM-325F FASCO F5C HHN 31-90A SS FASCO F6 HHN 31-90 GREX PPN65 GREX SF9034H GRIP-RITE GRTFC83 GRIP-RITE GRTCH350 GRIZZLY H5571 GRIZZLY H6146 GRIZZLY H7944 HITACHI NR83AA HITACHI NR83AA2 HITACHI NR83AA3 HITACHI NR90AA HITACHI NR90AD HITACHI NR90ADPR HITACHI NR90GC HITACHI NR90GC2 ISM CHN933 MAKITA AN942 MAKITA AN943 MAX GS683CH MAX GS683CH-EX MAX SN883CH/34 MAX SN890CH/34 NORTHERN TOOL 1000992 PASLODE 5300 PWS PASLODE 5325 PASLODE 5350 PASLODE 900420 PASLODE CF325 PASLODE F350S PASLODE IM325 PASLODE IM325CT PASLODE IM350 PASLODE IMCT PASLODE PF350S PORTER CABLE FC350 PORTER CABLE FC350A POWERS W3-34CDH PRIMEAIR PCH350 RIDGID R350CHA SENCO FRAMEPRO 600 SENCO FRAMEPRO 601 SENCO FRAMEPRO 650 SENCO FRAMEPRO 651 SENCO FRAMEPRO 701XP SENCO FRAMEPRO 750XL SENCO FRAMEPRO 751XP SENCO GT90CH SENCO SN4 SENCO SN70 SENCO SN70XP SENCO SN901XP SENCO SN951XP SPOTNAIL NTD90 SPOTNAIL YTD90 STAN-TECH SDN11-PT-1 SUPCO SDF88
31-34 PAPER STRIP, STRUCTURAL CONNECTOR NAILS BOSTITCH F33PT BOSTITCH MCN150 BOSTITCH MCN250 GRIP-RITE GR150 GRIP-RITE GR250 GRIP-RITE GRSB150-112 GRIP-RITE GRSB250-212 HITACHI NR65AK HITACHI NR65AKS PASLODE 5250/65S-PP PASLODE PF150S-PP PASLODE F250S-PP PNEU TOOLS RN-150 PNEU TOOLS RN-250 PNEU TOOLS RNS-150 SENCO HN150 SENCO HN250
Not all tool models shown are compatible with all diameters and lengths in the fastener series shown.
69
15 WIRE COIL SIDING APACH CN-565 APACH CN-57E APACH CN-70E APACH CN-83E BESCO CN2755 BESCO CN2765 BOSTITCH N55C BOSTITCH N57C BOSTITCH N63CP BOSTITCH N64C BOSTITCH N65CP BOSTITCH N66C BOSTITCH N75C CRAFTSMAN 18214 DUO-FAST P275C FASCO F45C GREX CN60 GRIP-RITE GRTCS250 GRIZZLY H7950 GRIZZLY H8231 HITACHI NV65AC HITACHI NV65AH HITACHI NV75AG MAKITA AN611 MAX CN55 MAX CN550S MAX CN565 MAX CN565D MAX CN565S MAX CN665 MAX CN70 MAX HN65 PASLODE 3225/CN55 PORTER CABLE COIL200 PORTER CABLE COIL250 PRIMEAIR PCP250 SENCO PALLETPRO 57F SENCO SCN48 SENCO SCN49 SENCO SCN55S SENCO SCN56 SENCO SCN60XP SENCO SCN65XP SPOTNAIL MCW64 SPOTNAIL UCNM65 SUPCO SCN57
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
15 WIRE COIL ROOFING APACH RN-45E ARCHER CN45R ATRO CN134 BEA 554DC BEA 555DC BESCO RF3132 BESCO RF3145 BESCO RF3145P BOSCH RN175 BOSTITCH N12 BOSTITCH N12B BOSTITCH RN45 BOSTITCH RN45B BOSTITCH RN46 CAMPBELL HAUSFELD NC1545 CRAFTSMAN 154500 CRAFTSMAN 18180 CRAFTSMAN 18324 CRAFTSMAN 18444 DEWALT D51321 DUO-FAST DRN-45 DUO-FAST RN-175A GREX CR45 GREX CR50 GREX RN45 GRIP-RITE GRTCR175 GRIZZLY H7951 GRIZZLY H8230 HILTI RFC-1348 HITACHI NV45AB HITACHI NV45AB2 HITACHI NV45AB2S HITACHI NV45AC HITACHI NV45AE JAMERCO JTCJ-45R MAKITA AN451 MAKITA AN453 MAX CN12R MAX CN445R MAX CN450R MILWAUKEE 7120-21 NORTHERN TOOL 1000994 PALMGREN 91211 PASLODE 3175/44RCU PASLODE 3175RCU PASLODE F-275C/P275C PASLODE R175-C PASLODE CR175C PORTER CABLE RN175 PORTER CABLE RN175A PORTER CABLE 134R PREBENA 4X-CNZ45R PRIMEAIR PCR175 PRIMEAIR PCR200 RAMSOND CRN-45 RIDGID R175RND SENCO ROOFPRO 450 SENCO ROOFPRO 455XP SENCO SCN200R SENCO SCN40R SNAP-ON 870012 SPOTNAIL VRN45 STAN-TECH SDCN10-1 SUPCO SR168 SUREBONDER 9780 WEN 61782
Not all tool models shown are compatible with all diameters and lengths in the fastener series shown.
70
16 GAUGE, 20 ADHESIVE, T-STYLE HEAD DEWALT DC614KA DEWALT DC614KN DEWALT DC615KA DEWALT DC618K DUO-FAST FLOORMASTER 250BN GRIZZLY H7945 GRIZZLY H7995 HITACHI NT65GB PASLODE 900600 PASLODE IM250A PASLODE T250A-F16 SENCO GT65RHA
15 GAUGE, 25 ADHESIVE, FN STYLE APACH LT-1564AF ATRO MONZA 64 DB 18 BOSTITCH N60FN BOSTITCH N62FNK-2 BOSTITCH GFN 1564K MAKITA AF631 MAKITA AF632 MAX NF510/15-50 SPOTNAIL XBFN64 STAN-TECH SDN-15BR
Not all tool models shown are compatible with all diameters and lengths in the fastener series shown.
71
18-GAUGE STRAIGHT, ADHESIVE, T-STYLE HEAD BRADS ACCUSET A125BN ACCUSET A200BN AIRY 0241NK APACH LNF-32AC APACH LNF-42AC APACH LNF-50AC APACH LU-32FAC APACH LU-50FAC ARROW 091-ETF50PBN ARROW ET200 BESCO BN1842 BESCO BN1850 BESCO BN1855P BLACK & DECKER FSNS125 BLACK AND DECKER BDBN1202 BLACK AND DECKER FS1802BN BLACK AND DECKER FSBN125 BLACK AND DECKER FSNS125 BOSCH BNS200-18 BOSTITCH BT125K BOSTITCH BT125K-2 BOSTITCH BT1855K BOSTITCH BT200K-2 BOSTITCH BT35B BOSTITCH BT50B BOSTITCH GBT1850K BOSTITCH SB-1842BN BOSTITCH SB-1850BN BOSTITCH SB-2IN1 CADEX BN1850 CAMPBELL HAUSFELD NB0030 CAMPBELL HAUSFELD NB003099AV CAMPBELL HAUSFELD NB004099 CRAFTSMAN 18172 CRAFTSMAN 18173 CRAFTSMAN 18174 CRAFTSMAN 18323 DEWALT D51236K DEWALT D51238K DEWALT DC608K DUO-FAST DBN-4440 DUO-FAST DBN-4450 DUO-FAST SURESHOT 2232 DUO-FAST SURESHOT 4450 DUO-FAST SURESHOT 4450 ST EZ-FASTEN F18/32VM FASCO F20P GN31/40 FASCO F21T GN-40A CT FASCO R3C GN50SS GREX 1832 GREX 1850 GREX BS5032 GRIP-RITE GRTBN125 GRIP-RITE GRTBN200 GRIZZLY G6045 GRIZZLY G6046 GRIZZLY G6047 GRIZZLY G8126 GRIZZLY G9248 GRIZZLY H2911 GRIZZLY H2912 GRIZZLY H2913 GRIZZLY H5527 GRIZZLY H6332 GRIZZLY H7664 GRIZZLY H7679 HITACHI NT32AE HITACHI NT32AE2 HITACHI NT50AD HITACHI NT50AE HITACHI NT50AE2 HITACHI NT50GS ISM BN 18-125 JAMERCO JTBN 1832 JAMERCO JTBN 1850 MAKITA AF502 MAKITA AF503 MAKITA AF505 MAX NF201/18-35 MAX NF211/18-25 MAX NF211/18-50 MAX NF221/18-55 MAX NF235F/18 MAX NF255-ST/18 MAXUS MXN10299 MAXUS MXN10499 MILWAUKEE 7150-21 PALMGREN 91181 PASLODE 2138-F18II PASLODE 901000 PASLODE IM200-F18 PASLODE T125-F18 PASLODE T200-F18 PORTER CABLE BN125A PORTER CABLE BN138 PORTER CABLE BN200A PORTER CABLE BN200B PORTER CABLE BN200V12 PREBENA 2P-J50SDS-S90 PREBENA 2X-J50SD-S90 PRIMEAIR PFB125 PRIMEAIR PFB200 RIDGID R213BNA SENCO AIRFREE 25 SENCO FINISHPRO 15 SENCO FINISHPRO 18 SENCO FINISHPRO 25XP SENCO FINISHPRO 2N1 SENCO SLP20XP SENCO LS5 SENCO SLP20 SPOTNAIL CB1820 SPOTNAIL CB1832 SPOTNAIL CB1850 SPOTNAIL TB1840 SPOTNAIL WB1850 STAN-TECH SDN 18BR STANLEY TRE50 SUPCO F30/32 SUPCO F32 SUPCO F32X SUPCO S1840E SUPCO S1850E WEN 61715 WEN 61720 WESTWARD 4VZ69 WESTWARD 4VZ70
Not all tool models shown are compatible with all diameters and lengths in the fastener series shown.
72
2 " CROWN, 1512 GAUGE (Similar to Bostitch BCS Series) GREX MS1250 GRIP-RITE GR200FS GRIZZLY H5977 HIGHPRO FS50 HITACHI N5009AF PORTA-NAILS 472 POWERNAIL 445FS POWERNAIL 445FS w/Power Roller PRIMATECH P220 PRIMATECH P250S PRIMATECH P260 SPOTNAIL FS7550 SPOTNAIL MS7564 SUPCO SFS
APACH MFS-50 BESCO MFS 50 BOSTITCH MIIIFS DUO-FAST FLOORMASTER 200-S EAGLE FS-50
7
16 " CROWN, 16 GAUGE (Similar to Senco N Series) DUO-FAST SM7648 FASCO F4P-G-50 FASCO FC3 G-40 CT GREX 1151 GRIP-RITE GRTSM200 GRIZZLY G6044 HITACHI N5008AB HITACHI N5008AC HITACHI N5008AC2 ISM MC716200 MAKITA AT1150A MAX TA551/16-11 MAX TA551/76 MAX TA551A-16-11 PORTER CABLE MS200 PRIMEAIR PSI200 SENCO SDS45XP SENCO SKS N SENCO SNS40 SENCO SNS41 SENCO SNS44XP SENCO SNS45 SENCO SNS45XP SENCO SNS50 SENCO SNS50XP SPOTNAIL MS6650I SPOTNAIL XS6650 STAN-TECH SD716-716 SUPCO SN38 SUPCO SN50X
APACH LU-851F APACH LU-851L APACH LU-864F BESCO MS 851S BOSTITCH 438S5 BOSTITCH 650S5 CADEX TNS16851 DEWALT D51430 DUO-FAST MS-7664E DUO-FAST SM-7664
2 " CROWN, 16 GAUGE (Similar to Paslode GS Series) PASLODE 3150-S16 PASLODE 3200-S16P PASLODE 900078NT PASLODE IM200-S16 PASLODE PA-200 PASLODE S200-S16
Not all tool models shown are compatible with all diameters and lengths in the fastener series shown.
73
2 " CROWN, 16 GAUGE (Similar to Bostitch BCS Series) BOSTITCH 750S4 BOSTITCH T36-1 BOSTITCH T38 BOSTITCH T40S4 BOSTITCH T50S4 BOSTITCH T55S4 CRAFTSMAN 18410 FASCO HD GRIZZLY G6772 ISM VULCANO 16NC SPOTNAIL HL7616A SPOTNAIL HL7616AP SPOTNAIL MS76-8650I SPOTNAIL XS76-8650 SUPCO SBP50
BESCO 951 FS BESCO MS 951S BOSTITCH 438S4 BOSTITCH 538S4 BOSTITCH 650S4 BOSTITCH 650S4-1
1" CROWN, 16 GAUGE (Similar to Senco P Series) BESCO WS 2538 BESCO WS 2638 CRAFTSMAN 18415 DUO-FAST KW1748 DUO-FAST RS1748 DUO-FAST SW1748 FASCO F30-SNW-50R FASCO F3C SNW-38TL CT ROOF FASCO R3C-SNW-38R GREX 2638 GRIP-RITE GRT1200-2 HITACHI N3824A HITACHI N5024A HITACHI N5024A2 MAKITA AT2550A PRIMEAIR PSW150 SENCO MW SENCO MWXP SENCO PW SENCO PW150 SENCO PW150R SENCO PW2 SENCO PW200 SENCO SPS SENCO WC150XP SENCO WC200XP SPOTNAIL XS3640 SPOTNAIL XS3650 STAN-TECH SDS16-1 SUPCO SSW2640
4" CROWN, 18 GAUGE (Similar to Senco L Series) CADEX SF9032B CADEX SF9040L CAMPBELL HAUSFELD SN258K CENTRAL PNEUMATIC 45728-6VGA CRAFTSMAN 18169 CRAFTSMAN 18171 CRAFTSMAN 18176 CRAFTSMAN 18435 DEWALT D51420K DEWALT D51422K DUO-FAST 1848F DUO-FAST DNS-1840 DUO-FAST KB-1836 DUO-FAST KN-1848A DUO-FAST SURESHOT 1820 DUO-FAST SURESHOT 1832 DUO-FAST SURESHOT 1832ST DUO-FAST SURESHOT 1848 DUO-FAST SURESHOT 1848F DUO-FAST SURESHOT 1848SL FASCO F20-40 FASCO F20P 90-25 FASCO F20T 90-30 CT FASCO F20T 90-40 CT FASCO F21P 90-25A FASCO F21T 90-40A FASCO F25A-90/40 FASCO F3C 90-40 CT 1 GREX 9040-GR GREX BS5032 GRIP-RITE GRTSN100 GRIP-RITE GRTSN150 GRIP-RITE GRTSN150A GRIZZLY G8126 GRIZZLY G9248 GRIZZLY H2912 GRIZZLY H2913 GRIZZLY H7664 HIGHPRO AS4090 HIGHPRO AS9040L HITACHI N3804AA HITACHI N3804AB HITACHI N3804AB2 HITACHI N3804AB3 ISM 18NC150 MAKITA AT638 MAX TA238/18-6 MAX TA238A/18-6 MAXUS MXN103 MAXUS MXN10499 MILWAUKEE 7155-21 PORTA-NAILER 461 PORTER CABLE NS100A PORTER CABLE NS100B PORTER CABLE NS150A PORTER CABLE NS150B PREBENA 2P-E40SDS-S90 PREBENA 2X-E40SD-S90 PRIMEAIR PSN125 RIDGID R150 FSA SENCO SKS L SENCO SLS18MG SENCO SLS20 SENCO SLS20XP-L SENCO SLS25XP SENCO SLS25XP-L SPOTNAIL FS4825 SPOTNAIL HL3852 SPOTNAIL TS4825 SPOTNAIL WS4840 STAN-TECH SDS18-14-26 SUPCO DF40 SUPCO SK9032 SUPCO SK9040 WEN 61710 WESTWARD 4VZ68
ACCUSET A100LS ACCUSET A150LS AIRY ASF-0638P AIRY ASM-0645 AIRY AST-0626S APACH AFS-9040 APACH LU-32FAC APACH LU-50FAC APACH LU-9025AC APACH LU-9032AC APACH LU-9040HAC APACH LU-9040HK APACH LU-9040K APACH LU-9040LAC ATRO MINOR 90/38 BEA 90/25-552 BEA 90/32-611 BEA 90/38-150 BEA 90/40-621 BESCO 9025 FS BESCO 9038 FS BESCO NS 9025 BESCO NS 9038LW BESCO NS 9040HD BLACK AND DECKER FSNS125 BOSCH STN150-18
Not all tool models shown are compatible with all diameters and lengths in the fastener series shown.
74
Our involvement in the structural connector industry led Simpson Strong-Tie to create our first proprietary fastener, the Strong-Drive SDS screw, over 15 years ago.
Since then we have used our expertise in structural connections and fasteners to expand the Strong-Drive line of structural screws. The SDS screw is ideal for certain connector installations as well as some wood-to-wood applications The SD structural-connector screw is the first, and only, screw approved for use with some of our most popular connectors The SDW is specifically designed for fastening multi-ply members such as plated trusses, engineered-lumber products and solid-sawn lumber
75
Stamp
S1.5
FEATURES:
Designed for installation in Simpson Strong-Tie structural connectors as well as wood-to-wood applications Available with a double-barrier coating and type 316 stainless steel 38" hex head Patented 4-CUT point (coated version) and type-17 point (stainless version) enable easy driving with no pre-drilling and minimal splitting Double-barrier coating provides corrosion resistance equivalent to hot-dip galvanization Head is stamped with the Simpson Strong-Tie = sign and fastener / length for easy identication after installation A low-speed 12" drill with a 38" hex driver is the recommended tool for installation Codes/Standards: ICC-ES ESR-2236
S2 S2.5
3" 3 1 2"
Thread Length
S3
S3.5
S4.5
S5
S6
S8
SDS 14"x3"
U.S. Patent 6,109,850; 5,897,280; 7,101,133; 7,832,173
Double-Barrier Coating
Size (in.)
1
Retail Pack Fasteners Per Pack 25 25 25 25 10 25 10 10 25 10 50 Model No. SDS25112-R25 SDS25200-R25 SDS25212-R25 SDS25300-R25 SDS25312-R10 SDS25312-R25L SDS25412-R10 SDS25500-R10 SDS25500-R25L1 SDS25600-R10 SDS25800-R50
1
Mini Bulk Fasteners Per Pack 300 250 200 150 125 100 100 100 Model No. SDS25112MB SDS25200MB SDS25212MB SDS25300MB SDS25312MB SDS25412MB SDS25500MB SDS25600MB Fasteners Per Pack 1500 1300 1100 950 900 800 500 600 400
4 x 112
1
4 x 2
4 x 212
1
4 x 3
4 x 312 4 x 412
1
4 x 5 4 x 6 4 x 8
1 1
Retail Pack Fasteners Per Pack 25 25 25 25 25 25 Model No. SDS25112SS-R25 SDS25200SS-R25 SDS25212SS-R25 SDS25300SS-R25 SDS25312SS-R25 SDS25312SS-R25L1 Fasteners Per Pack 1500 1300 1100 950 900
4 x 112
1
4 x 2
1
4 x 2 2
1
4 x 3
4 x 312
76
Finish/ Material
Thread Length (in.) 1 114 112 2 214 234 234 314 3 4 1 114 112 2 214
1
Steel Side Plate Shear (100) 16 ga 250 250 250 250 250 250 250 250 250 250 250 250 250 250 14 ga & 12 ga 250 290 390 420 420 420 420 420 420 250 290 390 420 420
Steel Side Plate Shear (100) 1 16 ga 180 180 180 180 180 180 180 180 180 180 180 180 180 180 14 ga & 12 ga 180 210 280 300 300 300 300 300 300 180 210 280 300 300 10 ga or Greater 180 210 300 300 300 300 300 300 300 180 210 300 300 300
4 x 112
1
10 ga or Greater 250 290 420 420 420 420 420 420 420 250 290 420 420 420
4 x 2 4 x 3 Double-Barrier Coating
4 x 212
1
1 1
4 x 312 4 x 412
1 1 1
4 x 112
1
4 x 212
1
4 x 312
1. Allowable loads for SDS screws are based on ICC-ES Code Report ESR-2236. Screws may be provided with the 4CUT or Type-17 point. 2. SDS screws install best with a low speed 12" drill with a 38 " hex head driver. 3. Allowable loads are shown at the wood load duration factor of CD = 1.00. Loads may be increased for load duration up to a CD = 1.60.
4. Allowable withdrawal load for DF/SP/SCL is 172 lbs./in. and for SPF/HF withdrawal is 150 lbs./in.. Total withdrawal load is based on actual thread penetration into the main member. 5. LSL wood-to-wood applications that require 4 12", 5", 6" and 8" SDS screws are limited to interior-dry use only. 6. Minimum spacing requirements are listed in ICC-ES ESR-2236.
Model No.
1
4 230 230
Model No.
1
4 190 195
1. Noted loads are based on ICC-ES Code Report ESR-2236 and/or testing per ICC AC233 and assume a minimum main member thickness of the screw length minus the side member thickness. All other allowable loads are based on the 2005 National Design Specication (NDS) and a minimum penetration of 6D = 1.45" into the main member. 2. Values are valid for a connection involving only two members. Where the side and main members have different specic gravities, the lower values shall be used.
3. Allowable loads are also applicable to structural composite lumber (e.g., LVL, PSL, and LSL) having an equivalent specic gravity of 0.50 or greater. 4. Allowable loads are shown at the wood load duration factor of CD = 1.00. Loads may be increased for load duration by the building code up to a CD = 1.60. The Designer shall apply all adjustment factors required per NDS. 5. Loads are based on installation into the side grain of the wood members with the screw axis perpendicular to the wood bers. 6. Loads apply to appropriate stainless-steel models.
77
SP 325 475
4 x 312 4 x 412
355 395
2x Solid Sawn
1. Allowable loads are based on Simpson Strong-Tie laboratory testing with a safety factor of 5 applied to the average ultimate test load. 2. Allowable loads are based on 1 12" thick main members and assume no gap between side and main members. 3. Allowable loads are shown at the wood load duration factor of CD = 1.00. Loads may be increased for load duration by the building code up to a CD = 1.60. The designer shall apply all adjustment factors required per NDS. 4. For applications with 2x side members, use allowable loads based on the lower of side member or main member species. 5. The Designer is responsible for the design of wood members.
12" min. 3" min. (typ.) 1" min. 112" min. 12" min. (typ.)
114"
58"
min. (typ.)
6" (typ.)
12" min.
min. (typ.)
Allowable Shear Loads for Installations into the Narrow Face of 2x Main Members
Size (in.)
1 1
4 x 312 4 x 4 2
1
250 250
190 190
SDS Screw
2x sole plate Wood structural sheathing fastened per code 2" min.
2x stud
SDS screws
Ledger-to-Stud Assembly
Model No.
1. Allowable loads are based on testing per ICC AC233 and are limited to parallel-to-grain loaded solid sawn main members (2" nominal). Wood side members may be loaded parallel or perpendicular to grain (see footnote 4). 2. DF/SP allowable loads are based on wood members having a minimum specic gravity of 0.50, and SPF/HF allowable loads are based on wood members having a minimum specic gravity of 0.42. Where the side and main members have different specic gravities, the lower values shall be used. 3. Allowable loads are shown at the wood load duration factor of CD = 1.00. Loads may be increased for load duration by the building code up to a CD = 1.60. 4. Minimum spacing of fasteners is 3" o.c., minimum end distance is 3" for all parallel-to-grain loaded members, or 4" for all perpendicular-to-grain loaded members, and minimum edge distance is 3 4" for all parallel-to-grain loaded members, or 1 12" for perpendicular-to-grain loaded side members. 5. Screws may be installed with an intermediate layer of wood structural panel between the side and main member provided the wood structural panel is fastened to the main member per code and the minimum penetration of the screw into the main member (excluding the wood structural panel) is met.
Size (in.)
Model No.
Allowable Loads (lbs) Minimum Sole Plate Penetration 114" Min. LVL Rim Board 114" Min. LSL Rim Board Nominal into Size Rim Board4 DF/SP SPF/HF DF/SP SPF/HF (in.) (in.) Sole Plate Sole Plate Sole Plate Sole Plate 2x 2x 2x or 3x 2 2 2 190 190 190 190 190 190 220 220 220 190 190 190
Sole plate Wood structural sheathing fastened per code 2" minimum
4 x 4 2
1 1
4 x 5 4 x 6
1. Allowable loads are based on testing per ICC AC233 and are limited to parallel-to-grain loading. 2. Allowable loads are shown at the wood load duration factor of CD = 1.00. Loads may be increased for load duration by the building code up to a CD = 1.60. 3. Minimum spacing of fasteners is 6" o.c., minimum end distance is 6", and minimum edge distance is 58". 4. Wood structural panel up to 1 18" thick is permitted between the sole plate and rim board provided it is fastened to the rim board per code and the minimum penetration of the screw into the rim board is met.
Maximum Deck Joist Span Band Joist Material and Size Up to 6 ft. Up to 8 ft. Up to 10 ft. Up to 12 ft. Up to 14 ft. Up to 16 ft. Up to 18 ft.
Maximum On-Center Spacing of Fasteners (in.) 2" Nominal Sawn Lumber 1" Min. Oriented Strand Board (OSB) Rim Board 118" Min. Oriented Strand Board (OSB) Rim Board or 114" Min. Structural Composite Lumber 2" Nominal Sawn Lumber 1" Min. Oriented Strand Board (OSB) Rim Board 1 8" Min. Oriented Strand Board (OSB) Rim Board or 114" Min. Structural Composite Lumber 13" 12" 15" 9" 8" 10" 10" 9" 11" 7" 6" 8" 8" 7" 9" 5" 5" 6" 6" 6" 7" 4" 4" 5" 5" 5" 6" 4" 3" 4" 5" 4" 5" 3" 3" 4" 4" 4" 5" 3" 2" 3"
1. Solid-sawn band joists shall be Spruce-Pine-Fir, Hem-Fir, Douglas Fir-Larch, or Southern Pine species. Ledger shall be Hem-Fir, Douglas Fir-Larch, or Southern Pine species. 2. Fastener spacings are based on single fastener testing of the Strong-Drive SDS screw with a safety factor of 5.0 and include NDS wet service adjustment factor. 3. Multiple ledger plies shall be fastened together per code independent of the SDS screws.
4. SDS screw spacing values (above) are equivalent to 2009 IRC Table R502.2.2.1, based on testing of the Strong-Drive SDS screw with a factor of safety of 5.0. The table above also provides SDS screw spacing for a wider range of materials commonly used for band joists, and an alternate loading condition as required by some jurisdictions. 5. Screw models SDS25312, SDS312SS and SDS25500.
1 2"
Wood structural panel sheathing max. thickness fastened per code Band joist per Table 112" minimum from top of ledger and band joist
Ledger fastener spacing may be offset up to 3" to avoid interference with joist attachment
SDS wood screws stagger vertically space in accordance with Table 112" minimum from bottom of ledger and band joist
79
4"
Identification on all SDW screw heads
W 22
X.X X
Stamp
W22
3.00
W22
W22
3.37
4.37
W22
W22
4.62
5.00
W22
W22
6.00
Installation:
SDW screws install best with a low-speed 12" drill motor and a T-40 6-lobe bit. The matched bit included with the screws is recommended for best results. Pre-drilling is typically not required. SDW screws may be installed through metal truss plates as approved by the Truss Designer, provided the requirements of ANSI/TPI 1-2007 Section 8.9.2 are met (pre-drilling required through the plate using a maximum of 532" bit). Screw heads that are countersunk ush to the wood surface are acceptable if the screw has not spun out. Individual screw locations may be adjusted up to 3" to avoid conicts with other hardware or to avoid lumber defects.
TL
6.37
W22
6.75
SDW
U.S. Patents 5,897,280; 7,101,133; 7,832,173
Thread Length (TL) (in.) 1716 1916 1716 1716 1916 1716 1716 1916
Retail Pack 1 Typical Application2 2x/Truss SCL 2x/Truss Desert 2x/Truss SCL/3x2PCT 2x/Truss Desert 2x/Truss SCL/4x2PCT Fasteners Per Pack 50 50 50 50 50 50 50 50 Packs Per Master Carton 6 6 4 4 4 4 4 4 Model No. SDW22300-R50 SDW22338-R50 SDW22438-R50 SDW22458-R50 SDW22500-R50 SDW22600-R50 SDW22638-R50 SDW22634-R50
3
Mini-Bulk Bucket1 Fasteners Per Pack 250 250 200 200 200 200 200 200 Model No. SDW22300MB SDW22338MB SDW22438MB SDW22458MB SDW22500MB SDW22600MB SDW22638MB SDW22634MB Fasteners Per Pack 950 900 600 600 600 500 500 500
Bulk 1 Model No. SDW22300 SDW22338 SDW22438 SDW22458 SDW22500 SDW22600 SDW22638 SDW22634
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
1. Retail and mini-bulk packs include one deep, 6-lobe, T-40 driver bit; bulk packs include two driver bits. 2. Typical screw application key: 2x/Truss = Solid-sawn dimensional lumber and plated wood trusses. 2x/Truss Desert = Solid-sawn dimensional lumber and plated wood trusses in desert environments (scant lumber).
SCL = 1 4" plies of structural-composite lumber. SCL/3x2PCT = 1 34" plies of structural-composite lumber or double 3x2 parallel-chord trusses. SCL/4x2PCT = 134" or 312" plies of structural-composite lumber or double 4x2 parallel-chord trusses. 3. If assembly is less than or equal to 4 916" thick, use the SDW22438. 4. If assembly is less than or equal to 6 316" thick, use the SDW22600.
80
Side Member
Main Member
Load
1. For minimum penetration into main member of 1 8", use 235 lbs. for DF/SP and 210 lbs. for SPF/HF.
Single Fastener Shear Loads for Solid Sawn and 2x Truss Loaded on Point Side
Assembly 2-ply 2x/Truss 3-ply 2x/Truss Desert 3-ply 2x/Truss 4-ply 2x/Truss Desert 4-ply 2x/Truss Model No. SDW22300 SDW22438 SDW22458 SDW22600 SDW22638 Nominal Thread Nominal Main Screw Length Length Side Member Member (L) (TL) Thickness Penetration (in.) (in.) (in.) (in.) 21516 1716 112 1 381 3 7 1 16 3 1 381 4 8 5 7 4 8 1 16 3 1 381 6 1716 412 1 381 6 38 1716 412 1 381 DF/SP Allowable Shear (lbs.) 325 275 275 275 275 SPF/HF Allowable Shear (lbs.) 255 255 255 255 255
Side Member
Main Member
Load
1. For minimum penetration into main member of 1 18", use 235 lbs. for DF/SP and 210 lbs. for SPF/HF.
Single Fastener Shear Loads for LVL, PSL and LSL Loaded on Head Side
Assembly 2-ply 134" SCL 3-ply 134" SCL 4-ply 134" SCL 2-ply 312" SCL Model No. SDW22338 SDW22500 SDW22634 SDW22634 Nominal Screw Length (L) (in.) 338 5 634 634 Thread Length (TL) (in.) 1916 1916 1916 1916 Nominal Main Equivalent Specific Equivalent Specific Side Member Member Gravity 0.50 Gravity 0.42 Thickness Penetration Allowable Shear Allowable Shear (in.) (in.) (lbs.) (lbs.) 134 134 134 312 1581 314 5 314 400 400 400 400 255 325 385 Load
Side Member
Main Member
1. For minimum penetration into main member of 1 12", use 300 lbs.
Single Fastener Shear Loads for LVL, PSL and LSL Loaded on Point Side
Assembly 2-ply 134" SCL 3-ply 134" SCL 4-ply 134" SCL 2-ply 312" SCL Model No. SDW22338 SDW22500 SDW22634 SDW22634 Nominal Screw Length (L) (in.) 338 5 634 634 Thread Length (TL) (in.) 1916 1916 1916 1916 Nominal Main Equivalent Specific Equivalent Specific Side Member Member Gravity 0.50 Gravity 0.42 Thickness Penetration Allowable Shear Allowable Shear (in.) (in.) (lbs.) (lbs.) 134 312 514 312 1581 112 112 314 400 300 300 400 255 255 255
Side Member
Main Member
Load
1. For minimum penetration into main member of 1 12", use 300 lbs.
81
3"
3"
1"
1. To transfer uniform or concentrated loads applied to simply supported spans on assembly top chord: a. Space screws as required to transfer half the load into the supporting truss. b. Minimum screw spacing shall be 4" o.c. 2. To transfer concentrated loads applied to simply supported spans on an assembly top chord or vertical web: a. Concentrated loads must be applied at a panel point. b. Screws to be installed within 12" of the concentrated load on top-chord assembly 3. Gap between the trusses shall not exceed 18". Concentrated Load 4. Floor sheathing shall be screwed or nailed to each top-chord ply. (Fastener spacing per the applicable Code requirements, or 12" o.c.) 12" Max. 12" Max. 5. SDW screws shall not be installed in areas where lumber wane exceeds 14". 6. Hangers on skewed girders: a. Hanger loads not exceeding 34" o.c. on a skewed girder (resulting from uniformly spaced joists up to 24" o.c.) may be converted to a uniform load. Strong-Drive b. For girders with hanger load spacing in excess of 34" o.c. the loads SDW screw (typ.) shall be considered as concentrated loads at the applicable locations. 7. Other configurations acceptable as long as approved by Truss Designer.
Uniform Load
Sideloaded Multi-Ply Assemblies Allowable Uniform Load Applied to Either Outside Member
Multiple Members Assembly Components A-W 2 -ply 2x/Truss B-W C-W 3 -ply 2x/Truss 4 -ply 2x/Truss Nominal DF/SP SPF/HF Screw Loaded SDW @ 12" o.c. SDW @ 16" o.c. SDW @ 24" o.c. SDW @ 12" o.c. SDW @ 16" o.c. SDW @ 24" o.c. Length Side 2 Rows 3 Rows 2 Rows 3 Rows 2 Rows 3 Rows 2 Rows 3 Rows 2 Rows 3 Rows 2 Rows 3 Rows (in.) 21516 Either 1300 1950 975 1465 650 975 1020 1530 765 1150 510 765 Head 1200 1800 900 1350 600 900 975 1465 730 1095 490 730 438 or 4 58 Point 825 1240 620 930 415 620 765 1150 575 860 385 575 Head 1065 1600 800 1200 535 800 905 1360 680 1020 455 680 6 or 638 Point 735 1100 550 825 365 550 680 1020 510 765 340 510
3. When hangers are installed on point side, hanger face fasteners must be a minimum of 3" long. 4. Tables are based on Main Member Penetration as noted in Tables 1 and 2. 5. Hanger load spacing on the multi-ply assembly should not exceed 24" o.c. Exception: On a skewed girder, hanger loads up to 34" o.c. (resulting from joists uniformly spaced up to 24" o.c.) may be converted to a uniform load.
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
1. Each ply is assumed to carry same proportion of load. 2. Loads may be applied to the head side and point side concurrently provided neither published allowable load is exceeded. (Example: a 3-ply DF assembly with a head side load of 1300 plf and point side load of 900 plf may be fastened together with 3 rows of SDW @ 16" o.c.)
W 22
X.X X
W 22
X.X X
Point Side
Point Side
Point Side
Head Side
Point Side
Head Side
Head Side
Head Side
W 22
X.X X
58" 58"
Min. stagger
W 22
X.X X
W 22
X.X X
Assembly A-W
Assembly B-W
Assembly C-W
Assembly F-W
Spacing Requirements
Sideloaded Multi-Ply LVL, PSL and LSL Assemblies Allowable Uniform Load Applied to Either Outside Member
Multiple Members Assembly A-W B-W C-W F-W Components 2-ply SCL 3-ply SCL 4-ply SCL 2-ply 312" SCL Nominal Screw Length (in) 338 5 634 634 Loaded Side Either Head Point Head Point Either SDW @ 12" o.c. 2 Rows 1600 1200 900 1065 800 1600 3 Rows 2400 1800 1350 1600 1200 2400 SDW @ 16" o.c. 2 Rows 1200 900 675 800 600 1200 3 Rows 1800 1350 1015 1200 900 1800 SDW @ 24" o.c. 2 Rows 800 600 450 535 400 800 3 Rows 1200 900 675 800 600 1200
82
1. Each ply is assumed to carry same proportion of load. 2. Loads may be applied to the head side and point side concurrently provided neither published allowable load is exceeded. (Example: a 3-ply assembly with a head side load of 1300 plf and point side load of 1000 plf may be fastened together with 3 rows of SDW @ 16" o.c.)
3. When hangers are installed on point side, hanger face fasteners must be a minimum of 3" long. 4. Tables are based on Main Member Penetration as noted in single-fastener load tables.
OR
SD10
(SD9 similar) U.S. Patent 7,101,133
SD Structural-Connector Screw
Size #9 #9 #10 #10
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
Retail Pack Packs Per Master Model No. Carton 10 SD9112R100 6 10 6 SD9212R100 SD10112R100 SD10212R100
Contractor Pack Packs Per Master Model No. Carton 3 SD9112R500 2 3 2 SD9212R500 SD10112R500 SD10212R500
Mini Bulk Fasteners Per Pack 3000 2000 3000 2000 Model No. SD9112MB SD9212MB SD10112MB SD10212MB
DF/SP Allowable Loads (lbs) Shear (100) Side Plate Thickness (in.) 32 - 12 105 118 127 147
23
SPF/HF Allowable Loads (lbs) Shear (100) Side Plate Thickness (in.)
15
Size (in.)
Model No.
32 - 34 133 168
32 - 12 93 99 102 106
23
32 - 34 94 126
1 1 1 1
1. Allowable loads are shown at the wood load duration factor of CD = 1.00. Loads may be increased for load duration per the building code up to a CD = 1.60. 2. The 1532" and 2332" side members must be plywood or OSB with minimum equivalent specific gravities of 0.50 for DF and SP design values, and 0.42 for SPF and HF design values.
83
SD10
1 1
Model No. L30* L50* L70* L90* LCE4* LPC4* LSCZ LSTA9* LSTA12* LSTA15* LSTA18* LSTA21* LSTA24* LSTA30* LSTA36* LSTI49* LSTI73* LTP4* LU24 (10d)* LU26 (10d)* LU28 (10d)* LU210 (10d)* LUC26Z (10d)* LUC26Z (16d)* LUC210Z (10d)* LUC210Z (16d)* LUS24* LUS24-2* LUS26* LUS26-2* LUS28* LUS28-2* LUS210* LUS210-2* MST27* MST37* MST48 MST60 MST72 MSTA9* MSTA12* MSTA15* MSTA18* MSTA21* MSTA24* MSTA30* MSTA36* MSTA49*
SD9
1 1
SD10
1 1
Model No. MSTC28* MSTC40* MSTC52* MSTC66* MSTC78* MSTI26* MSTI36* MSTI48* MSTI60* MSTI72* MTS12* MTS16* MTS20* NS1* NS2* PBS44A PC44* PC44-16* PSPN58Z* RR* RSP4* ST9* ST12* ST18* ST2115* ST2122* ST22* ST292* ST2215* ST6215* ST6224* ST6236* THASR/L29 THASR/L29-2 THASR/L422 TP15* TP311* TP35* TP37* TP39* TP411* TP45* TP47* TP49* TP57* TPA37* TPA39* TPA57* VTCR
SD9
1 1
SD10
1
* These connectors are code listed under ICC-ES ESR-3096 when installed with the SD screw. Check withyour local building department to determinewhetherthe correct size of SD structural-connector screw may be used as a suitable substitute for nails.
84
Since testing of the SD structural-connector screw is ongoing, Simpson Strong-Tie will continue to add newly-approved connectors to this list. For the most current list of approved connectors, load values and applications visit www.strongtie.com/sd.
HAND-DRIVE SCREWS
Our extensive assortment of hand-drive screws covers the range of applications from decking and siding to roofing and steel framing and everything in-between.
With a number of corrosion resistant materials and finishes available you can be sure to find the best fastening solution for long-term durability and easy installation. Coated carbon steel as well as types 305, 316 and 410 stainless steel A selection of head styles and drive types Thread patterns and points to match a variety of applications Proprietary features that make fastening easier Painted options to match popular decking and siding colors
85
HAND-DRIVE SCREWS
Trim-Head Decking Screw
FEATURES:
Fasten wood decking and some composite decking materials Trim-style head is less noticeable on the decking surface Trim head offers a clean, nished look Available with Quik Guard coating and in type 305 stainless steel Quik Guard Coated Screw (For information on corrosion, materials and coatings, see pages 10-13.) Self-countersinking nibs under the head ensure ush installation Type-17 point for fast starts Durable coating in four colors allows heads to blend with decking Type 305 Stainless Steel Screw Box threads for easier driving Sharp point for easy starts Pre-drilling recommended near board ends to prevent splitting Driver bit included in each package These screws are also available collated for use with our Quik Drive auto-feed screw driving system. See page 160 for details.
Brown
Gray
Red
Tan
Head Diameter* (in.) 0.246 0.246 0.246 0.246 0.246 0.246 0.246 0.246
70-Count Model No. DTHB212R70 DTHG212R70 DTHR212R70 DTHT212R70 DTHB3R70 DTHG3R70 DTHR3R70 DTHT3R70
350-Count Model No. DTHB212R350 DTHG212R350 DTHR212R350 DTHT212R350 DTHB3R350 DTHG3R350 DTHR3R350 DTHT3R350
1750-Count Model No. DTHB212MB DTHG212MB DTHR212MB DTHT212MB DTHB3MB DTHG3MB DTHR3MB DTHT3MB
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
* #2 undersized square drive (replacement bit model SSBIT2U-2, see page 113 for more information)
* #2 square drive (replacement bit model SSBIT2-2, see page 113 for more information)
These coated fasteners possess a level of corrosion resistance that makes them suitable for use in some exterior and corrosive environments and with some preservative-treated woods. For applications in higher-exposure applications, consider type-300 series stainless-steel fasteners for superior corrosion resistance. See pages 10-13 for additional important information before selecting a fastener for a specific application. 86
HAND-DRIVE SCREWS
Trim-Head Decking Screw, Stainless Steel
FEATURES:
Fasten wood decking and some composite decking materials Available with either square or 6-lobe drive, in types 305 and 316 stainless steel Trim-style head is less noticeable on the decking surface Type-17 point for fast starts Coarse threads approximately 23 up the shank draw the decking and other material tightly to the substrate The 6-lobe drive option helps reduce cam-out, resulting in easier driving and longer driver-bit life A wide variety of painted heads available, see pages 88-89 350-count packs contain enough screws to fasten 100 sq. ft. of decking (6" nominal-width boards installed on 16" o.c. joists) Choose type 316 for seaside applications and superior corrosion resistance Driver bit included in each package Pre-drilling recommended near board ends to prevent splitting
* #7 screw: #1 square drive (replacement bit model SSBIT1-2, see page 113 for more information); #9x3 12" screw: #1 square drive; #9x4" screw: #2 square drive (replacement bit model SSBIT2-2, see page 113 for more information)
Head Approx. Length Diameter Count (in.) (in.) per lb. 158 214 3 0.230 0.230 0.230 195 138 98
Bulk Bucket Count 4000 3000 2000 Model No. T07162FBB T07225FBB T07300FBB
#7 #7 #7
* #1 square drive (replacement bit model SSBIT1-2, see page 113 for more information)
Bulk Bucket Count 4000 3000 2000 Model No. S07162FTB S07225FTB S07300FTB
* T-15 6-lobe drive (replacement bit model SSBIT15-2, see page 113 for more information)
* T-15 6-lobe drive (replacement bit model SSBIT15-2, see page 113 for more information)
HAND-DRIVE SCREWS
Trim-Head Decking Screw, Stainless Steel (cont.)
Painted Head, Square Drive
FEATURES:
Durable, coated nish painted heads blend with decking material Heads colored to match Azek and Veka decking and trim, and also match a wide variety of decking colors from other manufacturers Driver bit included in each package
Black
Gray
Ip
Khaki
Kona Mocha
Tan
White
Head Diameter (in.) 0.230 0.230 0.230 0.230 0.230 0.230 0.230 0.230 0.230 0.230 0.230 0.230 0.230 0.230 0.230
Head Color Ip White Almond Azek Gray Black Gray Ip Khaki Kona Mocha Tan White Gray Ip Tan
350-Count Model No. S07162FJI S07162FJW S07225FJA S07225FZJ S07225FJB S07225FJG S07225FJI S07225FJK S07225FKJ S07225FJM S07225FJT S07225FJW S07300FJG S07300FJI S07300FJT
1750-Count Model No. S07162FCI T07162FCW S07225FCA S07225FCZ S07225FCBB S07225FCG S07225FCI S07225FBK S07225FKB S07225FCM S07225FCT S07225FCW S07300FCG S07300FCI S07300FCT
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
#7 screw: #1 square drive (replacement bit model SSBIT1-2, see page 113 for more information)
Head Diameter (in.) 0.230 0.230 0.230 0.230 0.230 0.230 0.230 0.230
350-Count Model No. T07162FJG T07162FJI T07162FJT T07162FJW T07225FJG T07225FJI T07225FJT T07225FJW
1750-Count Model No. T07162FCG T07162FCI T07162FCT T07162FCW T07225FCG T07225FCI T07225FCT T07225FCW
#7 screw: #1 square drive (replacement bit model SSBIT1-2, see page 113 for more information)
88
HAND-DRIVE SCREWS
Trim-Head Decking Screw, Stainless Steel (cont.)
Painted Head, 6-Lobe Drive
FEATURES:
Durable, coated nish painted heads blend with decking material Heads colored to match Trex Escapes PVC decking, and also match a wide variety of decking colors from other manufacturers Driver bit included in each package
Acorn
Almond
Black
Gray
Jatoba
Khaki
Kona
Lt. Gray
Mocha
Pewter
Sahara
Tan
White
Head Diameter* (in.) 0.230 0.230 0.230 0.230 0.230 0.230 0.230 0.230 0.230 0.230
Head Color White Acorn Black Kona Lt. Gray Pewter Sahara Jatoba Lt. Gray Tan
350-Count Model No. S07162TJW S07225TJA S07225TJB S07225TKJ S07225TJG S07225TJE S07225TJS S08250TJJ S08250TJG S08250TJT
1750-Count Model No. S07162TCW S07225TCA S07225TCB S07225TKC S07225TCG S07225TCE S07225TCS S08250TCJ S08250TCG S08250TCT
* T-15 6-lobe drive (replacement bit model SSBIT15-2, see page 113 for more information)
Head Diameter* (in.) 0.230 0.230 0.230 0.230 0.230 0.230 0.230 0.230 0.230 0.230 0.230
Head Color White Acorn Black Lt. Gray Pewter Sahara Almond Gray Khaki Mocha White
350-Count Model No. T07162TJW T07225TJA T07225TJB T07225TJG T07225TJE T07225TJS T08250FJA T08250FZJ T08250FJK T08250FJM T08250FJW
1750-Count Model No. T07162TCW T07225TCA T07225TCB T07225TCG T07225TCE T07225TCS T08250FCA T08250FZC T08250FBK T08250FCM T08250FCW
* T-15 6-lobe drive (replacement bit model SSBIT15-2, see page 113 for more information)
89
HAND-DRIVE SCREWS
Bugle-Head Wood Decking Screw
FEATURES:
Fasten all types of wood decking including cedar, redwood and preservative-treated woods (non-hardwood) Available with either square or 6-lobe drive, in types 305 and 316 stainless steel Type-17 point for fast starts Coarse threads approximately 23 up the shank draw the decking and other material tightly to the substrate Painted heads available, see page 92 6-lobe drive option helps prevent driver-bit cam-out, resulting in easier driving and longer bit life 350-count packs contain enough screws to fasten 100 sq. ft. of decking (6" nominal-width boards installed on 16" o.c. joists) Choose type 316 for seaside applications and superior corrosion resistance Driver bit included in each package Pre-drilling recommended near board ends to prevent splitting
Head Diameter (in.) 0.344 0.344 0.344 0.344 0.344 0.344 0.344 0.344 0.344 0.344 0.344 0.344 0.344 0.344 0.344 0.344 0.344 0.344 0.344 0.344 0.344 0.344 0.344 0.430 0.430 0.430 0.430 0.430 0.430 0.430 0.430 0.430 0.430 0.430 0.430
Approx. Count per lb. 408 352 295 243 195 285 226 185 150 128 109 102 82 172 153 134 115 96 88 82 68 56 54 56 48 42 36 32 29 28 24 36 33 26 21
1 lb. Model No. S06062DB1 S06075DB1 S06100DB1 S06125DB1 S06162DB1 S08075DB1 S08112DB1 S08125DB1 S08162DB1 S08200DB1 S08225DB1 S08250DB1 S08300DB1 S10100DB1 S10125DB1 S10150DB1 S10175DB1 S10200DB1 S10225DB1 S10250DB1 S10300DB1 S10350DB1 S10375DB1 S12250DB1 S12300DB1 S12350DB1 S12400DB1 S12450DB1 S12500DB1 S12550DB1 S12600DB1 S14300DB1 S14350DB1 S14400DB1 S14500DB1
5 lb. Model No. S06062DB5 S06075DB5 S06100DB5 S06125DB5 S06162DB5 S08075DB5 S08112DB5 S08125DB5 S08162DB5 S08200DB5 S08225DB5 S08250DB5 S08300DB5 S10100DB5 S10125DB5 S10150DB5 S10175DB5 S10200DB5 S10225DB5 S10250DB5 S10300DB5 S10350DB5 S10375DB5 S12250DB5 S12300DB5 S12350DB5 S12400DB5 S12450DB5 S12500DB5 S12550DB5 S12600DB5 S14300DB5 S14350DB5 S14400DB5 S14500DB5
350-Count Model No. S08C125PAK S08C162PAK S08C200PAK S08C225PAK S08C250PAK S08C300PAK S10C250PAK S10C300PAK S10C350PAK
Bulk Bucket Count 12,000 10,000 8000 5000 4000 10,000 5000 5000 4000 3000 3000 2000 1500 4500 4000 3500 3000 2500 2000 2000 1500 1000 1000 2000 1500 1000 800 750 500 500 600 1000 750 700 500 Model No. S06062DBB S06075DBB S06100DBB S06125DBB S06162DBB S08075DBB S08112DBB S08125DBB S08162DBB S08200DBB S08225DBB S08250DBB S08300DBB S10100DBB S10125DBB S10175DBB S10200DBB S10225DBB S10250DBB S10300DBB S10350DBB S10375DBB S12250DBB S12300DBB S12350DBB S12400DBB S12450DBB S12500DBB S12550DBB S12600DBB S14300DBB S14350DBB S14400DBB S14500DBB
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
8 4
1 114 158
3
118 114 158 2 214 212 3 1 114 1 2 134 2 214 212 3 312 334 212 3 312 4 412 5 512 6 3 312 4 5
1
S10150DBB
* #6, #8 and #10 screws: #2 square drive (replacement bit model SSBIT2-2); #12 and #14 screws: #3 square drive (replacement bit model SSBIT3-2). See page 113 for information on replacement driver bits.
90
HAND-DRIVE SCREWS
Bugle-Head Wood Decking Screw (cont.)
Square Drive*, Type 316 Stainless Steel
Size #8 #8 #8 #8 #10 #10 #10 #10 #12 #12 #12 #12 #12 #12 #12 #12 #14 #14 #14 #14 #14 Length (in.) 1 4 158 2 2 2 2 2 2 3 312 2 2 3 312 4 4 2 5 512 6 3 312 4 5 6
1 1 1 1 1
Head Diameter (in.) 0.344 0.344 0.344 0.344 0.344 0.344 0.344 0.344 0.430 0.430 0.430 0.430 0.430 0.430 0.430 0.430 0.430 0.430 0.430 0.430 0.430
1 lb. Model No. T08125DB1 T08162DB1 T08200DB1 T08250DB1 T10200DB1 T10250DB1 T10300DB1 T10350DB1 T12250DB1 T12300DB1 T12350DB1 T12400DB1 T12450DB1 T12500DB1 T12550DB1 T12600DB1 T14300DB1 T14350DB1 T14400DB1 T14500DB1 T14600DB1
5 lb. Model No. T08125DB5 T08162DB5 T08200DB5 T08250DB5 T10200DB5 T10250DB5 T10300DB5 T10350DB5 T12250DB5 T12300DB5 T12350DB5 T12400DB5 T12450DB5 T12500DB5 T12550DB5 T12600DB5 T14300DB5 T14350DB5 T14400DB5 T14500DB5 T14600DB5
350-Count Model No. T08C125PAK T08C162PAK T08C200PAK T08C250PAK T10C250PAK T10C300PAK T10C350PAK
Bulk Bucket Count 5000 4000 3000 2000 2500 2000 1500 1000 2000 1500 1000 800 750 500 500 600 1000 750 700 500 500 Model No. T08125DBB T08162DBB T08200DBB T08250DBB T10200DBB T10250DBB T10300DBB T10350DBB T12250DBB T12300DBB T12350DBB T12400DBB T12450DBB T12500DBB T12550DBB T12600DBB T14300DBB T14350DBB T14400DBB T14500DBB T14600DBB
* #8 and #10 screws: #2 square drive (replacement bit model SSBIT2-2); #12 and #14 screws: #3 square drive (replacement bit model SSBIT3-2). See page 113 for information on replacement driver bits.
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
Head Diameter (in.) 0.344 0.344 0.344 0.344 0.344 0.344 0.344
1 lb. Model No. S06125DT1 S06162DT1 S08162DT1 S08200DT1 S10250DT1 S10300DT1 S10350DT1
5 lb. Model No. S06125DT5 S06162DT5 S08162DT5 S08200DT5 S10250DT5 S10300DT5 S10350DT5
Bulk Bucket Count 5000 4000 4000 3000 2000 1500 1000 Model No. S06125DTB S06162DTB S08162DTB S08200DTB S10250DTB S10300DTB S10350DTB
* #6 screws: T-15 6-lobe drive (replacement bit model SSBIT15-2); #8 screws: T-20 6-lobe drive (replacement bit model SSBIT20-2); #10 screws: T-20 6-lobe drive (replacement bit model SSBIT25-2). See page 113 for information on replacement driver bits.
91
HAND-DRIVE SCREWS
Bugle-Head Wood Decking Screw (cont.)
6-Lobe Drive*, Type 316 Stainless Steel
Size #10 #10 Length (in.) 2 2 3
1
* T-25 6-lobe drive (replacement bit model SSBIT25-2, see page 113 for more information)
Gray
Ip
Tan
* #2 square drive (replacement bit model SSBIT2-2, see page 113 for more information)
92
HAND-DRIVE SCREWS
Dexxter Composite-Decking Screw
FEATURES:
Fasten composite deck boards and deck trim Available with Quik Guard coating (square drive) or types 305 and 316 stainless steel (6-lobe drive). For information on corrosion, materials and coatings, see pages 10-13. Smaller head is less visible Unique thread form removes exhaust while driving to reduce mushrooming in composite decking Type-17 point for fast starts 350-count packs contain enough screws to fasten 100 sq. ft. of decking and 1750-count packs contain enough screws to fasten 500 sq. ft. of decking. Both assume 6" nominal-width boards installed on 16" o.c. joists. Choose type 316 for seaside applications and superior corrosion resistance Driver bit included in each package Colors with an 01 suffix (Brown 01) are formulated to match Trex Transcend decking (see next page for color reference) and also match a wide variety of decking colors from other manufacturers Brown 01 Gray 01 Red 01 The Quik-Guard coated version of this screw is also available collated for use with our Quik Drive auto-feed screw driving system. See page 162 for details.
Tan 01
Head Diameter* (in.) 0.265 0.265 0.265 0.265 0.265 0.265 0.265 0.265
Head Color Brown 01 Gray 01 Red 01 Tan 01 Brown 01 Gray 01 Red 01 Tan 01
350-Count Model No. DDX212BR01R350 DDX212GR01R350 DDX212RD01R350 DDX212TN01R350 DDX3BR01R350 DDX3GR01R350 DDX3RD01R350 DDX3TN01R350
1750-Count Model No. DDX212BR01MB DDX212GR01MB DDX212RD01MB DDX212TN01MB DDX3BR01MB DDX3GR01MB DDX3RD01MB DDX3TN01MB
* #2 undersized square drive (replacement bit model SSBIT2U-2, see page 113 for more information)
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
* T-20 6-lobe drive (replacement bit model SSBIT20-2, see page 113 for more information)
* T-20 6-lobe drive (replacement bit model SSBIT20-2, see page 113 for more information)
These coated fasteners possess a level of corrosion resistance that makes them suitable for use in some exterior and corrosive environments and with some preservative-treated woods. For applications in higher-exposure applications, consider type-300 series stainless-steel fasteners for superior corrosion resistance. See pages 10-13 for additional important information before selecting a fastener for a specific application. 93
HAND-DRIVE SCREWS
Dexxter Composite-Decking Screw (cont.)
Painted Head, 6-Lobe Drive
FEATURES:
Durable, coated nish painted heads blend with decking material Colors with an 01 sufx (Brown 01) are formulated to match Trex Transcend decking (color reference below), and will also match a wide variety of decking colors from other manufacturers Driver bit included in each package
Brown
Gray
Ip
Redwood
Tan
Head Diameter* (in.) 0.265 0.265 0.265 0.265 0.265 0.265 0.265 0.265 0.265 0.265 0.265 0.265 0.265 0.265 0.265 0.265 0.265 0.265 0.265 0.265 0.265 0.265
Head Color Brown Gray Ip Redwood Tan Brown Brown 01 Gray Gray 01 Ip Red 01 Redwood Tan Tan 01 Brown 01 Gray Gray 01 Ip Red 01 Redwood Tan Tan 01
70-Count Model No. S10150XCB S10150XCG S10150XCI S10150XCR S10150XCT S10250XCB S10250XCG S10250XCI S10250XCR S10250XCT S10300XCG S10300XCI S10300XCR S10300XCT
350-Count Model No. S10150XPB S10150XPG S10150XPI S10150XPR S10150XPT S10250XPB S10250XPBR01 S10250XPG S10250XPGR01 S10250XPI S10250XPRD01 S10250XPR S10250XPT S10250XPTN01 S10300XPBR01 S10300XPG S10300XPGR01 S10300XPI S10300XPRD01 S10300XPR S10300XPT S10300XPTN01
1750-Count Model No. S10150XBB S10150XBG S10150XBI S10150XBR S10150XBT S10250XBB S10250XBBR01 S10250XBG S10250XBGR01 S10250XBI S10250XBRD01 S10250XBR S10250XBT S10250XBTN01 S10300XBBR01 S10300XBG S10300XBGR01 S10300XBI S10300XBRD01 S10300XBR S10300XBT S10300XBTN01
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
* T-20 6-lobe drive (replacement bit model SSBIT20-2, see page 113 for more information)
94
HAND-DRIVE SCREWS
Composi-Lok Composite-Decking Screw
FEATURES:
Fasten composite deck boards Available with Quik Guard coating in four colors and type 305 stainless steel. For information on corrosion, materials and coatings, see pages 10-13. Square drive Cap-style head reduces mushrooming material, ensuring a cleaner-looking installation Cutting wings on the shaft counter-bore the deck board, helping to prevent fastener spin out Sharp point Driver bit included in each package Pre-drilling recommended near board ends to prevent splitting This screw is also available collated for use with our Quik Drive auto-feed screw driving system. See page 161 for details.
Brown
Gray
Red
Tan
* #2 undersized square drive (replacement bit model SSBIT2U-2, see page 113 for more information)
* #2 undersized square drive (replacement bit model SSBIT2U-2, see page 113 for more information)
These coated fasteners possess a level of corrosion resistance that makes them suitable for use in some exterior and corrosive environments and with some preservative-treated woods. For applications in higher-exposure applications, consider type-300 series stainless-steel fasteners for superior corrosion resistance. See pages 10-13 for additional important information before selecting a fastener for a specific application.
95
HAND-DRIVE SCREWS
Hardwood Decking Screw
FEATURES:
Penetrate the hardest wood products with ease Available in both at and trim heads, in type 305 and 316 stainless steel. Flat head style features self-countersinking nibs under the head. Unique 4-corner thread form with raised-ridge technology greatly reduces driving torque 6-lobe drive helps prevent driver-bit cam-out resulting in easier driving and longer bit life Choose type 316 stainless steel for seaside applications and superior corrosion resistance Threaded approximately 23 up the shank to tightly draw the decking to the joist Deck Packs contain enough screws to fasten 100 sq. ft. of decking and Contractor Buckets contain enough screws to fasten 500 sq. ft. of decking. Both assume 6" nominal-width boards installed on 16" o.c. joists. Driver bit included in each package Pre-drilling recommended near board ends to prevent splitting
Clam Shell Count 100 50 40 Model No. T08162DWP T10250DWP T10300DWP Count 350 350 350 350 250 100
Deck Pack Model No. T08162WPP T08200WPP T10250WPP T10300WPP T10350WPP T12400WPP
Bulk Bucket Count 4000 3000 1750 1750 1000 750 Model No. T08162WPB T08200WPB T10250WPB T10300WPB T10350WPB T12400WPB
* T-20 6-lobe drive (replacement bit model SSBIT20-2, see page 113 for more information)
* T-20 6-lobe drive (replacement bit model SSBIT20-2, see page 113 for more information)
Bulk Bucket Count 4000 1750 1750 Model No. T07162WPB T07225WPB T07300WPB
* T-15 6-lobe drive (replacement bit model SSBIT15-2, see page 113 for more information)
96
HAND-DRIVE SCREWS
Hardwood Decking Screw (cont.)
Painted Head
FEATURES:
Durable, powder-coated nish painted heads blend with decking material Driver bit included in each package
Ip
* T-20 6-lobe drive (replacement bit model SSBIT20-2, see page 113 for more information)
* T-15 6-lobe drive (replacement bit model SSBIT15-2, see page 113 for more information)
* #2 square drive (replacement bit model SSBIT2-2, see page 113 for more information)
97
Ordering Information Pack Quantity 100 Pack Model No. 100-EB TYS 175-EB TYS 275-EB TYS 175-EB TYW
Model EBE007MINI
1+
32
N/A
EBE004
1+
32
EBE004
175
175-EB162
Model EBE002
16 +
32
N/A
Model EBE005LC
N/A
EBE002
175 100
Model EBE006JR
1+
Live Cylinder design for expansive material Live Cylinder design for expansive material N/A Square-drive screws preferred
EBE005LC
Model 316TT TT
EBE006JR 175 175-EBTYJR
16 +
8 +
16
Model M d l EBEOA
Kodiak Composite
8 +
PVC Composites 98
7 7
8 + 8 +
1 3
N/A N/A
16
Model TP015
100
100-EBTYMI
Installation Information
As with all decking materials, please consult manufacturers installation instructions for deck height requirements and deck board spacing. All slots for the EB-TYs (except for the 316TT) can be cut using a #20 setting with a biscuit cutter/plate jointer or router with 5 32" slot cutter. Decking can be grooved the entire length of the board. Always butt boards over a joist. One method for installing butt ends is to cut the keel off the bottom of an EB-TY, slot the board ends, and insert the EB-TY. Another, more reliable method is to face-screw and plug.
Deck boards
If you have questions about which EB-TY to use, contact Simpson Strong-Tie.
Second deck board fastened with EB-TY and construction adhesive applied to top of oor joist
Floor joist
Installation Process
recommended when installing 1. Fasten the rst board using construction adhesive and screws, then cut composite deck boards as some slots where the board intersects joists using a 532" router bit or plate joiner adhesives will have an adverse (biscuit cutter #20) and install the rst EB-TY fasteners. Do not use reaction upon contact with construction adhesive with composite decking (see note on the right). certain plastics. 2. Cut slots in the next board where it intersects the joists. 3. Apply a bead of construction adhesive to the top of each joist and install the new board so that the slots t over the EB-TY fasteners installed in the rst board. 4. Insert EB-TY fasteners into each slot in the exposed edge of the board and fasten with screws. Bring the schematic below to your lumber yard. They will use it 5. Repeat the process until all boards are installed. to pre-groove your decking material to accept EB-TY fasteners.
0.500" 0.163"
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
Refer to the installation instructions (included) for more information. Consult composite decking manufacturers or wood suppliers installation instructions for deck height requirements and deck board spacing. Pre-grooving the entire length of the deck board is a time-saving alternative to individual grooves made with a router or plate joiner. Some types of composite lumber are available with grooves as an added feature. Have your lumber yard use the schematic on the right to pregroove boards to accept EB-TY fasteners.
*For model numbers TP015 and 316TT screws are to be driven at a 90 angle to the board face.
Ip Wood Plugs
FEATURES:
Made of high quality Ip and tapered for ease of use For use on decks using the EB-TY system (rst boards, aprons, etc.); also stairs, railings
Plug Diameter (in.)
3
16
HAND-DRIVE SCREWS
Strong-Drive SD Wafer-Head Screw
FEATURES:
Wafer head Deep Phillips drive reduces cam-out and makes driving easier Serrated threads for easier driving Sharp point for fast starts Clear zinc finish. For information on corrosion, materials and coatings, see pages 10-13.
Head Diameter* (in.) 0.418
Size #8
* #2 Phillips drive
SD8x1.25
Allowable Loads
DF/SP Allowable Loads (lbs.) Size (in.) Steel Side Plate Model No. Shear (100) 16 ga - 3 ga
5
SPF/HF Allowable Loads (lbs.) Steel Side Plate Shear (100) 16 ga - 3 ga 45 Withdrawal (100) 58
Withdrawal (100) 82
32 x 1 4
SD8x1.25
50
1. Allowable loads are shown at the wood load duration factor of CD = 1.00. Loads may be increased for load duration up to a CD = 1.60. 2. SD8x1.25 requires 34" minimum penetration into the main member. DO NOT USE SD8x1.25 wood screws with structural connectors unless specied and stated in this catalog.
For superior corrosion resistance in a range of applications including timber framing, pole barn construction, log homes, gutter installation and landscape timbers 4-corner thread form signicantly reduces driving torque Drive with standard 516" or 12" hex nut drivers
Package Count 10 10 10 10 10 10 10 10 10 Model No. T14500TP T14600TP T14800TP T37300TP T37400TP T37500TP T37600TP T37800TP T371000TP Count 100 100 100 50 100 100 50 50 25 25 25
Bucket Model No. T14450TTB T14500TTB T14600TTB T14800TTB T37300TTB T37400TTB T37500TTB T37600TTB T37800TTB T371000TTB T371200TTB
4 x 4 2 4" x 5" 4 x 6 4 x 8
16 16 16 16 2 2 2 2 2 2 2
1 1 3 3 3 3 3 3
8 x 3 8 x 4 8 x 5 8 x 6 8 x 8
1 1 1 1 1 1 1
8 x 10 8 x 12
100
HAND-DRIVE SCREWS
Fiber-Cement Screw
FEATURES:
Wafer head with self-countersinking nibs Square drive Type-17 point for fast starts Coarse thread full length (to within 516" of head) Driver bit included in each package Use 1 14" screws to attach ber cement siding to stress skin panels Use 1 58" screws to blind-fasten ber cement lap siding to wood
* #2 square drive (replacement bit model SSBIT2-2, see page 113 for more information)
Size #9 #9 #9 #9 #9 #9
101
HAND-DRIVE SCREWS
Trim-Head Screw with Sealing Washer
FEATURES:
Assemblies provide weathertight seal for use in exterior sheathing and roong applications Square drive Type-17 point for fast starts Washers are 58" in diameter and are made from type 302 stainless steel with a bonded neoprene gasket Other sizes available contact Simpson Strong-Tie for details
* #1 square drive (replacement bit model SSBIT1-2, see page 113 for more information)
Length (in.)
3 3
4 4
114 1 4
1
102
HAND-DRIVE SCREWS
Truss-Head Screw
FEATURES:
Fasten all materials to wood or wood-substitute materials Square drive Coarse thread Pre-drilling recommended dependent on substrate
Head Diameter* (in.) 0.374 0.374 0.374 0.374 0.374 0.374 0.374 0.374 0.374 0.374 0.374 0.374
Carton Quantity 100 1000 2000 100 1000 2000 100 1000 2000 100 1000 2000
Model No. S08C100TSC S08C100TSM S08100TSBC S08C125TSC S08C125TSM S08125TSBC S08C150TSC S08C150TSM S08150TSBC S08C250TSC S08C250TSM S08250TSBC
* #2 square drive (replacement bit model SSBIT2-2, see page 113 for more information)
Pancake-Head Screw
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
FEATURES:
Ideal for securing clips used in standing-seam roong Low-prole head Square drive Type-A point Type 410 stainless steel can be hardened through heat treatment, giving it the ability to drill through metal. It does not offer the same level of corrosion resistance of either type 305 or 316 stainless steel.
* #2 square drive (replacement bit model SSBIT2-2, see page 113 for more information)
103
HAND-DRIVE SCREWS
Marine Screw
FEATURES:
Designed to fasten securely in berglass, plywood and wood-substitute materials in applications exposed to harsh marine or many chemically caustic conditions Ideal for applying trim, rub rail and molding to berglass boat hulls Available with at, pan and oval heads Phillips drive Specially engineered, high/low thread form incorporates indentations (teeth) that cut easily and quickly through high-density materials Extra-sharp points speed screw starts during assembly Back-out resistance: once driven home, teeth lock the fastener into place (the thread indentations will resist back-out even after prolonged vibration) Screws up to 1" in length are fully threaded. Screws more than 1" long are threaded 23 of the shank length
Length (in.)
1
Head Diameter* (in.) 0.262 0.262 0.312 0.262 0.310 0.363 0.312 0.363 0.312 0.363 0.363
Nominal Screw Diameter (in.) 0.138 0.138 0.164 0.138 0.164 0.190 0.164 0.190 0.164 0.190 0.190
100-Count Model No. T06J050FXC T06J075FXC T08J075FXC T06J100FXC T08J100FXC T10J100FXC T08J125FXC T10J125FXC T08J150FXC T10J150FXC T10J200FXC
1000-Count Model No. T06J050FXM T06J075FXM T08J075FXM T06J100FXM T08J100FXM T10J100FXM T08J125FXM T10J125FXM
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
2 4 4
1 1 1 1 4 1 4 1 2 1 2 2
1 1 1 1
104
HAND-DRIVE SCREWS
Marine Screw (cont.)
Pan Head, Type 316 Stainless Steel
Size #6 #8 #10 #6 #8 #10 #6 #8 #10 #12 #14 #8 #10 #12 #14 #12 #14
* #2 Phillips drive
Length (in.)
1 1 1
Head Diameter* (in.) 0.263 0.314 0.365 0.263 0.314 0.365 0.263 0.314 0.365 0.416 0.483 0.314 0.365 0.416 0.483 0.416 0.483
Nominal Screw Diameter (in.) 0.138 0.164 0.190 0.138 0.164 0.190 0.138 0.164 0.190 0.216 0.242 0.164 0.190 0.216 0.242 0.216 0.242
100-Count Model No. T06J050PXC T08J050PXC T10J050PXC T06J075PXC T08J075PXC T10J075PXC T06J100PXC T08J100PXC T10J100PXC T12J100PXC T14J100PXC T08J125PXC T10J125PXC T12J150PXC T14J150PXC T12J200PXC T14J200PXC
1000-Count Model No. T06J050PXM T08J050PXM T10J050PXM T06J075PXM T08J075PXM T10J075PXM T06J100PXM T08J100PXM T10J100PXM T12J100PXM T14J100PXM T08J125PXM T10J125PXM T12J150PXM T14J150PXM T12J200PXM T14J200PXM
2 2 2 4 4 4
3 3 3
1 1 1 1 1 114 114 1 2 1 2 2 2
1 1
Length (in.)
3 3 3
Head Diameter* (in.) 0.262 0.312 0.363 0.262 0.312 0.363 0.396 0.445 0.312 0.363 0.312 0.363 0.396 0.445 0.396 0.445
Nominal Screw Diameter (in.) 0.138 0.164 0.190 0.138 0.164 0.190 0.216 0.242 0.164 0.190 0.164 0.190 0.216 0.242 0.216 0.242
100-Count Model No. T06J075OXC T08J075OXC T10J075OXC T06J100OXC T08J100OXC T10J100OXC T12J100OXC T14J100OXC T08J125OXC T10J125OXC T08J150OXC T10J150OXC T12J150OXC T14J150OXC T12J200OXC T14J200OXC
1000-Count Model No. T06J075OXM T08J075OXM T10J075OXM T06J100OXM T08J100OXM T10J100OXM T12J100OXM T14J100OXM T08J125OXM T10J125OXM T08J150OXM T10J150OXM T12J150OXM T14J150OXM T12J200OXM T14J200OXM
#6 #8 #10 #6 #8 #10 #12 #14 #8 #10 #8 #10 #12 #14 #12 #14
* #2 Phillips drive
4 4 4
105
HAND-DRIVE SCREWS
Self-Drilling Fiber-Cement Screw
FEATURES:
Fasten ber cement through furring strips to steel studs Wafer head, square drive, self-countersinking nibs under the head Threaded to within 516" of top of head #3 drill point Type 410 stainless steel can be hardened through heat treatment, giving it the ability to drill through metal. It does not offer the same level of corrosion resistance of either type 305 or 316 stainless steel. Warning: Hardened stainless-steel fasteners should not be used with steel framing in environments with high humidity, condensation or other moisture that will be present at the dissimilar-metal interface.
* #2 square drive (replacement bit model SSBIT2-2, see page 113 for more information)
Head Diameter* (in.) 0.230 0.230 0.230 0.230 0.230 0.230 0.230 0.230 0.230
Approx. Count per lb. 187 187 187 132 132 132 105 105 105
Carton Quantity 100 1000 5000 100 1000 4000 100 1000 2000
Model No. F07T162TDC F07T162TDM F07T162TDB F07T225TDC F07T225TDM F07T225TDB F07T300TDC F07T300TDM F07T300TDB
* #1 square drive (replacement bit model SSBIT1-2, see page 113 for more information)
106
For more information on drilling thickness capacities and drill speed recommendations see pages 16-17.
HAND-DRIVE SCREWS
Self-Drilling Wire-Lath Modied Truss-Head Screw
FEATURES:
Ideal for fastening metal lath to steel studs Also used to fasten corrugated siding panels to steel stud without pre-drilling. Securely fastens one to three panel thicknesses Phillips drive #3 drill point for quick penetration of aluminum panels without point walking Type 410 stainless steel can be hardened through heat treatment, giving it the ability to drill through metal. It does not offer the same level of corrosion resistance of either type 305 or 316 stainless steel. Warning: Hardened stainless-steel fasteners should not be used with steel framing in environments with high humidity, condensation or other moisture that will be present at the dissimilar-metal interface.
Length (in.)
9 9 9
Head Diameter* (in.) 0.423 0.423 0.423 0.423 0.423 0.423 0.423 0.423 0.423 0.423 0.423 0.423 0.423 0.423 0.423
Carton Quantity 100 1000 8000 100 1000 6000 100 1000 4000 100 1000 3000 100 1000 2500
Model No. F08T056KDC F08T056KDM F08T056KDB F08T075KDC F08T075KDM F08T075KDB F08T125KDC F08T125KDM F08T125KDB F08T162KDC F08T162KDM F08T162KDB F08T200KDC F08T200KDM F08T200KDB
16 16 16 4 4 4
3 3 3
* #2 square drive (replacement bit model SSBIT2-2, see page 113 for more information)
For more information on drilling thickness capacities and drill speed recommendations see pages 16-17.
107
HAND-DRIVE SCREWS
Self-Drilling Truss-Head Screw
FEATURES:
Secure single-ply membrane through insulation to steel purlins Phillips drive Tapping screw thread (13 threads per inch) Drill point Factory Mutual approved for fastening to 1622 gauge steel and wood decking Type 410 stainless steel can be hardened through heat treatment, giving it the ability to drill through metal. It does not offer the same level of corrosion resistance of either type 305 or 316 stainless steel. Warning: Hardened stainless-steel fasteners should not be used with steel framing in environments with high humidity, condensation or other moisture that will be present at the dissimilar-metal interface. These screws are special-order, non-stock items and are subject to minimum order quantities and longer lead times. Call Simpson Strong-Tie for details.
Threads Per Inch 1512 15 2 1512 1512 15 2 1512 15 2 1512 15 2 15 2 1512 1512 1512
1 1 1 1 1
Head Diameter* (in.) 0.438 0.438 0.438 0.438 0.438 0.438 0.438 0.438 0.438 0.438 0.438 0.438 0.438
Thread Length (in.) Full Full Full Full 3 8 378 3 8 378 3 8 3 8 378 378 378
7 7 7 7
Model No. F14C150T20 F14150TIPC F14C200T10 F14C300T10 F14C400T10 F14400TIPC F14C500T10 F14C600T5 F14600TIPC
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
For more information on drilling thickness capacities and drill speed recommendations see pages 16-17.
108
HAND-DRIVE SCREWS
Self-Drilling Bugle-Head Screw
FEATURES:
Fasten wood, plywood and OSB panels to steel studs Bugle heads drive ush with work surface Square-drive Tapping screw threads #3 drill point Type 410 stainless steel can be hardened through heat treatment, giving it the ability to drill through metal. It does not offer the same level of corrosion resistance of either type 305 or 316 stainless steel. Warning: Hardened stainless-steel fasteners should not be used with steel framing in environments with high humidity, condensation or other moisture that will be present at the dissimilar-metal interface.
Head Diameter* (in.) 0.344 0.344 0.344 0.344 0.344 0.344 0.344 0.344 0.344 0.344 0.344 0.344 0.344 0.344 0.344 0.344
Carton Quantity 100 1000 5000 100 1000 3000 100 1000 2500 100 1000 2000 100 1500 100 1000
Model No. F06T125BDC F06T125BDM F06T125BDB F08T162BDC F08T162BDM F08T162BDB F08T200BDC F08T200BDM F08T200BDB F10T250BDC F10T250BDM F10T250BDB F10T300BDC F10T300BDB F10T350BDC F10T350BDB
* #2 square drive (replacement bit model SSBIT2-2, see page 113 for more information)
For more information on drilling thickness capacities and drill speed recommendations see pages 16-17.
109
HAND-DRIVE SCREWS
Self-Drilling Flat-Head Screw with Wings
FEATURES:
Fasten wood, plywood and ber cement to steel up to 0.209" thick Flat countersunk head with self-countersinking nibs Square drive Machine screw thread, threaded full length Shank slot enhances thread formation in steel and removes exhaust Wings above drill point provide clearance hole in work piece so it wont climb up the shank, then break off as point engages the steel substrate 2 12" length for 2x wood header; 2" length for 1" and 54" boards Type 410 stainless steel can be hardened through heat treatment, giving it the ability to drill through metal. It does not offer the same level of corrosion resistance of either type 305 or 316 stainless steel. Warning: Hardened stainless-steel fasteners should not be used with steel framing in environments with high humidity, condensation or other moisture that will be present at the dissimilar-metal interface.
Head Diameter* (in.) 0.375 0.375 0.375 0.375 0.375 0.375 0.468 0.468
Carton Quantity 100 1000 2500 100 1000 1800 100 1000
Model No. F12C200FDC F12C200FDM F12C200FDB F12C250FDC F12C250FDM F12C250FDB F14C325FDC F14C325FDB
* #3 square drive (replacement bit model SSBIT3-2, see page 113 for more information)
For more information on drilling thickness capacities and drill speed recommendations see pages 16-17. 110
HAND-DRIVE SCREWS
Self-Drilling, Hex-Washer Head Screw
FEATURES:
Indented hex-washer head Tapping screw thread #3 drill point Available in Marutex and types 305 and 316 stainless steel Marutex is a heat-treated chrome-moly alloy that provides superior corrosion resistance to type 410 stainless steel and is suitable for more demanding applications Warning: Hardened stainless-steel fasteners should not be used with steel framing in environments with high humidity, condensation or other moisture that will be present at the dissimilar-metal interface. Types 305 and 316 stainless steel provide superior corrosion resistance and are suitable for softer materials such as aluminum and fiberglass (not steel)
Carton Quantity 100 1000 100 1000 100 1000 100 1000 100 1000 100 1000 100 1000 100 1000 100 1000 100 1000 100 1000 100 1000 100 1000 100 1000 100 1000 100 1000 100 1000 100 1000 100 1000 100 1000 100 1000
Marutex Model No. X08050HDUC X08050HDUM X08075HDUC X08075HDUM X08100HDUC X08100HDUM X10050HDUC X10050HDUM X10075HDUC X10075HDUM X10100HDUC X10100HDUM X10150HDUC X10150HDUM X12075HDUC X12075HDUM X12100HDUC X12100HDUM X12125HDUC X12125HDUM X12150HDUC X12150HDUM X12200HDUC X12200HDUM X12250HDUC X12250HDUM X12300HDUC X12300HDUM X14075HDUC X14075HDUM X14100HDUC X14100HDUM X14150HDUC X14150HDUM X14200HDUC X14200HDUM X14250HDUC X14250HDUM X14300HDUC X14300HDUM
Type 305 Stainless Steel Model No. S12125HDUC S12125HDUM S12150HDUC S12150HDUM S12200HDUC S12200HDUM S12250HDUC S12250HDUM S12300HDUC S12300HDUM
Type 316 Stainless Steel Model No. T08100HDUC T08100HDUM T12100HDUC T12100HDUM T12150HDUC T12150HDUM T12200HDUC T12200HDUM T12250HDUC T12250HDUM T12300HDUC T12300HDUM T12400HDUC T12400HDUM
For more information on drilling thickness capacities and drill speed recommendations see pages 16-17. 111
HAND-DRIVE SCREWS
Self-Drilling Hex-Washer Head Screw with Sealing Washer
FEATURES:
Indented hex-washer head Washers are type 302 stainless steel with bonded neoprene to provide a weather-resistant seal for exterior sheathing and roong applications Tapping screw thread #3 drill point Types 305 and 316 stainless steel provide superior corrosion resistance and are suitable for softer materials such as aluminum and berglass (not steel)
Washer Diameter (in.) 0.625 0.625 0.625 0.625 0.625 0.625 0.625 0.625
Carton Count 100 1000 100 1000 100 1000 100 1000
Model No. Type 305 S12125HOC S12125HOM S12150HOC S12150HOM S12200HOC S12200HOM Type 316 T12100XOC T12100XOM T12150XOC T12150XOM T12200XOC T12200XOM
16 16 16 16 16 16 16 16
For more information on drilling thickness capacities and drill speed recommendations see pages 16-17.
Storm-Panel Screw
FEATURES:
Ideal for attaching storm panels to wood, concrete and masonry Save time and money with a single installation The screw is made of type 305 stainless steel for corrosion resistance
(25) Stainless-steel storm-panel screws 14" x 3 716" (25) 14" zinc die-cast washered wing nuts (25) White plastic caps to protect threads after panels are removed (1) Hex driver bit for panel screws (1) 0.234" x 4 12" carbide-tipped drill bit
4" white plastic caps 4" zinc die-cast washered wing nuts
INSTALLATION
1. Drill a hole in the concrete or masonry base material using the drill bit provided. To pre-drill into wood, use a 316" bit. 2. Position the panel and drive the screw using the hex driver bit (included). Drive the screw deep enough so that the bottom of the threads for the wing nut are slightly below the surface of the panel. 3. Secure the panel with the wing nut. 4. To remove panels remove the wing nut, remove the panel and cover the threads on the screw with the plastic cap.
112
HAND-DRIVE SCREWS
Premium Driver Bits
Our industrial-grade driver bits are specially designed for a secure t with the recess of Simpson Strong-Tie fasteners. Available in both square and six-lobe drive congurations, our bits will outperform sub-standard bits commonly prone to cam-out and stripping.
113
Driving Systems
Quik Drive auto-feed screw driving systems turn repetitive fastening into opportunities to increase efficiency and save time.
Extensive research goes into the design of each system and screw to understand the intended applications, fastener performance demands and the work flow in which installations take place. This results in professional-quality auto-feed solutions that truly make work easier. Auto-feed attachments and collated fasteners eliminate the need to handle individual screws Extensions allow stand-up driving for appropriate applications, making work faster and more comfortable Tool systems and fasteners specifically designed for target applications
Quik Drive auto-feed screw driving systems are ideal for subfloor installation because they combine the efficiency of stand-up driving with the holding power of screws. Screws are superior to nails in this application because they reduce the gaps that cause floor squeaks. Recommended for wood and steel framing Fasten 2,000 sq. ft. in just over an hour Systems warn when screw misses the joist screw head spins rather than seating and disengaging the driver bit
PRO250 System
PRO250 System
1 12" 2 12"
1" 3"
Applications: Subfloor/sheathing, wall plates, stair treads, decks/docks, fiber-cement siding Expanded depth settings for high-density materials Reversible and replaceable non-skid teeth Sure-grip guide tube increases stability for a broad range of screws Two screw driving attachments for added versatility Details, pages 141-142
116
Applications: Subfloor/sheathing, fiber-cement siding Expanded depth settings for high-density flooring materials Uniform toenailing and countersink on slick surfaces Reversible and replaceable non-skid teeth Details, page 139
PRO250
PROSDD/CCS+
2"
2"
1 34"
1 34"
1 1516"
1 1516"
1 12"
1 12"
WSNTL SCREW If the joist is missed the unthreaded portion allows the screw to spin, alerting the user
PPSD11516S Pilot point allows #2 drill point to penetrate steel without the plywood riding up the threads
117
Quik Drive auto-feed screw driving systems are ideal for fastening decking because they combine the efficiency of stand-up driving with the holding power of screws, providing the best long-term results. Fast, precise and consistent fastening Screws resist withdrawal that leaves nail heads sticking out of the decking surface over time Screws available for most decking materials: PVC, composite, hardwood and preservative-treated wood
PRO300S System
PRO300S System
1 12" 3"
1" 3"
118
Applications: Decks/docks, subfloor, wall plates, stair treads Expanded depth settings for high-density materials Reversible and replaceable non-skid teeth Includes a decking nose clip to position decking screws quickly and precisely every time Uniform toenailing and countersink on slick surfaces Sure-grip guide tube increases stability for a broad range of screws Details, page 140
PROSDD/CCS+
PRO300S
2 12", 3"
2 12", 3"
Dexxter The cap head and reverse thread eliminates mushrooming and leaves a cleaner-looking installation
2 12", 3"
2 12", 3"
2 12", 3"
2 12", 3"
Composi-Lok Counterboring Wings and Cap Head Designed to prevent fastener spin out with harder materials in cold or wet conditions and mushrooming of composite decking material during installation
2 12"
2 12"
DHPD Paddle-Style Drill Point Penetrate the hardest woods with ease
For information on corrosion, materials and coatings, see pages 10-13. These coated fasteners possess a level of corrosion resistance that makes them suitable for use in some exterior and corrosive environments and with some preservative-treated woods. For applications in higher-exposure applications, consider type-300 series stainless-steel fasteners for superior corrosion resistance. See pages 10-13 for additional important information before selecting a fastener for a specific application. 119
Quik Drive auto feed screw driving systems are ideal for fastening drywall because they provide a fast, efficient solution with a precision countersink adjustment that produces consistent dimples. Recommended for wood and steel framing Increases comfort and productivity Reduces labor, waste and expense
PRO200 System
PRO200 System
1" 2"
Applications: Drywall, wood underlayment, fiberglass-backed gypsum sheathing Compact body for reduced weight and easy handling Smooth nose will not mar drywall surface Slim profile allows driving in corners Details, page 138
PRO250DW Attachment
Applications: Drywall, wood underlayment, fiberglass-backed gypsum sheathing Compact body for reduced weight and easy handling Smooth nose will not mar drywall surface Slim profile allows driving in corners Details, page 152
1 78" 2 12"
120
PRO200
PRO250DW
2", 2 12"
1 14", 1 58"
N/A
1 14", 1 58"
N/A
Drywall to steel, #2 point, yellow-zinc and N2000 galvanized coatings available (54, 43 mils / 16, 18 ga), page 171
1 14", 1 58"
1 78", 2 38"
1 14"
N/A
1 78"
1 78"
For information on corrosion, materials and coatings, see pages 10-13. These coated fasteners possess a level of corrosion resistance that makes them suitable for use in some exterior and corrosive environments and with some preservative-treated woods. For applications in higher-exposure applications, consider type-300 series stainless-steel fasteners for superior corrosion resistance. See pages 10-13 for additional important information before selecting a fastener for a specific application. 121
Quik Drive auto-feed screw driving systems provide a time-saving fastening method combined with the holding power of screws. Screw threads create a secure, vibration-resistant connection that prevents sheathing from shaking loose while travelling from the panel yard to the jobsite. Fast, precise and consistent screw driving Increases comfort and productivity Reduces labor, waste and expense
QDA158NS Attachment
QDA158NS Attachment
1" 1 58"
1 14", 1 58"
QDPRO200 System
1" 2"
1 14"
1 14"
Applications: Fiberglass-backed gypsum sheathing, drywall, wood underlayment Compact body for reduced weight and easy handling Slim profile allows driving in corners Details, page 138
DWCG Screw
Sharp point, N2000 galvanized coating, page 170
1 14", 1 58"
1 14", 1 58"
For information on corrosion, materials and coatings, see pages 10-13. These coated fasteners possess a level of corrosion resistance that makes them suitable for use in some exterior and corrosive environments and with some preservative-treated woods. For applications in higher-exposure applications, consider type-300 series stainless-steel fasteners for superior corrosion resistance. See pages 10-13 for additional important information before selecting a fastener for a specific application. 122
Applications: Fiberglass-backed gypsum sheathing Lightweight, compact, and affordably priced Equipped with non-skid teeth for stability Slim profile allows driving in corners Adaptors included to fit DeWalt, Makita and Milwaukee screwdriver motors Details, page 153
QDA158NS
PRO200G2
Quik Drive auto-feed screw driving systems save time when installing siding because they enable fast, efficient fastening along with a countersink adjustment to ensure consistent results. Recommended for wood or steel framing Fast and accurate screw placement
PRO250 System
1 12" 2 12"
Applications: Fiber-cement siding, subfloor/sheathing es Uniform toenailing and countersink on slick surfaces Non-skid nose increases stability Long-lasting reliability for a wide variety of applications Details, page 139
PROLDH System
Applications: Fiber-cement siding, cement backerboard Slim profile allows driving in corners Drives fasteners that meet ANSI standards Compact body for reduced weight and easy handling Details, page 143
PRO250
PROCGB
PROLDH
PRO300S
1 58"
1 58"
2 14"
PROLDH System
1 14" 2"
Applications: Fiber-cement siding, cement backerboard Slim profile allows driving in corners Drives fasteners that meet ANSI standards Compact body for reduced weight and easy handling Details, page 144
CB3BLG Screw
Type-17 point, C-3 galvanized coating, page 169
1 14", 1 58"
1 14", 1 58"
CB3BLGHL Screw
High-low thread, C-3 galvanized coating, page 169
#2 Drill Point with Wings Wings cut a path, protecting the integrity of the threads and break away before penetrating the steel.
1 14", 1 58"
1 14", 1 58"
For information on corrosion, materials and coatings, see pages 10-13. These coated fasteners possess a level of corrosion resistance that makes them suitable for use in some exterior and corrosive environments and with some preservative-treated woods. For applications in higher-exposure applications, consider type-300 series stainless-steel fasteners for superior corrosion resistance. See pages 10-13 for additional important information before selecting a fastener for a specific application.
123
The Quik Drive PROPP150 auto-feed screw driving system is ideal for standing-seam metal roong because the Precision Placement nosepiece cuts installation time and the collated fasteners eliminate handling of individual screws. Innovative Precision Placement nosepiece allows for easy location of the hole in the clip Hands-free screw advancement speeds installation Collated fastener strips reduce waste and prevent damage to roof panels Suitable for panel clips up to 2 12" tall Also ideal for fastening panel anges for snap-and-seam metal roong and installing trim and drip edge
PROPP150 System
PROPP150
PC Screw
(Quik Guard only)
Type-17 point, clear-zinc or Quik Guard coating and type 410 stainless steel, pages 172-173
1", 1 12"
1"
PCULP Screw
These coated fasteners possess a level of corrosion resistance that makes them suitable for use in some exterior and corrosive environments and with some preservative-treated woods. For applications in higher-exposure applications, consider type-300 series stainless-steel fasteners for superior corrosion resistance. See pages 10-13 for additional important information before selecting a fastener for a specific application. 124
(Quik Guard only)
Type-17 point, clear-zinc or Quik Guard coating and type 410 stainless steel, pages 172-173
1", 1 12"
X Self-Drilling Screw
(Quik Guard only)
5 16" hex head, #3 drill point, clear-zinc or Quik Guard coating, page 176
1"
The Quik Drive BGP300 auto-feed screw driving system is ideal for metal roofing and siding because it speeds the installation of washered screws while providing consistent results. Patented belt collation enables auto-feed fastening of screws with EPDM-backed washers Profile guide on nosepiece ensures uniform screw placement The extension enables stand-up fastening on low-pitch roofs Depth control prevents over-driving Designed to eliminate skipped screws, reducing screw waste Easy loading keeps work moving Screws available in 21 colors to match popular roofing-panel colors
BGP300 System
BGP300
1 12", 2"
For information on corrosion, materials and coatings, see pages 10-13. These coated fasteners possess a level of corrosion resistance that makes them suitable for use in some exterior and corrosive environments and with some preservative-treated woods. For applications in higher-exposure applications, consider type-300 series stainless-steel fasteners for superior corrosion resistance. See pages 10-13 for additional important information before selecting a fastener for a specific application. 125
Quik Drive auto-feed screw driving systems are a time-saving solution for tile roofing because the collated fastening strips eliminate the handling of individual screws and the attachments are designed for easy location of the holes in the tiles. Recommended for clay and concrete roofing tile Drives fasteners that meet state and local building code requirements Window in nose allows exact screw placement
PRORF System
PRORF System
1 12" 2 12"
WSCD Screw
Miami-Dade compliant, meets ASTM A641 class 1 standard, class 55 galvanized coating, page 171
2 12"
2 12", 3"
PRO300SRF System
2 12" 3"
WSCT Screw
Meets ASTM A641 class 1 standard, page 171
2 12"
2 12"
Applications: Concrete and clay tile roofing Secure depth settings prevent tile breakage Window in guide tube allows exact screw placement Long-lasting reliability for tile roofing applications Details, page 148
SSWSCB Screw
Miami-Dade compliant, type 305 stainless steel, page 171
2", 2 12"
2 12"
For information on corrosion, materials and coatings, see pages 10-13. These coated fasteners possess a level of corrosion resistance that makes them suitable for use in some exterior and corrosive environments and with some preservative-treated woods. For applications in higher-exposure applications, consider type-300 series stainless-steel fasteners for superior corrosion resistance. See pages 10-13 for additional important information before selecting a fastener for a specific application. 126
Applications: Concrete and clay tile roofing e Secure depth settings prevent tile breakage Window in guide tube allows exact ct screw placement Long-lasting reliability for tile roofing applications Details, page 147
PRORF
PRO300SRF
Quik Drive auto-feed screw driving systems save time when fastening cold-formed steel framing because the collated fastening strips eliminate the handling of individual screws and the attachments hold the screw in place while it drills through the material. Recommended for cold-formed steel framing and steel deck stitching Screws held in place as they drill through steel Collated fastener strips reduce wasted screws Increases comfort and productivity
PROPH Attachment
PROPH Attachment
3
4" 1"
Applications: Steel to steel Compact body for reduced weight and easy handling Slim profile allows driving in corners Long-lasting reliability for targeted applications Details, page 152
PROPH
PROHX516
4"
PROHX516 System
7
4"
8" 1"
Applications: Metal-to-metal stitching, roof pan construction Engineered to drive screws for steel fastening Precise depth adjustment prevents over and under driving Long-lasting reliability for targeted applications Details, page 151
4"
X Self-Drilling Screw
16" hex head, #3 or #4 drill point, clear-zinc coating, page 176
5
8" - 1"
For information on corrosion, materials and coatings, see pages 10-13. 127
The Quik Drive PROPP150 auto-feed screw driving system is the right choice for steel decking because it provides an efficient fastening solution that is safer and easier than welding or P.A.T.. Features an extended nosepiece for easy access to valley Stand-up driving increases comfort and productivity Precise depth adjustment prevents over and under driving One system for fastening steel decking to structural members and steel stitching No special inspection or certification required as with welding or P.A.T. fastening
PROPP150 System
PROPP150
XQ Self-Drilling Screw
5
16" hex head, #4 or #5 drill point, Quik Guard coating, page 176
X Self-Drilling Screw
5
1"
4"
For information on corrosion, materials and coatings, see pages 10-13. These coated fasteners possess a level of corrosion resistance that makes them suitable for use in some exterior and corrosive environments and with some preservative-treated woods. For applications in higher-exposure applications, consider type-300 series stainless-steel fasteners for superior corrosion resistance. See pages 10-13 for additional important information before selecting a fastener for a specific application.
128
Quik Drive auto-feed screw driving systems are ideal for underlayment because the variety of screws solves challenges such as driving over radiant heat panels and the extension enables stand-up-and-drive installation. Recommended for cement and fiber-cement board and wood underlayment Ideal for installing subflooring over radiant heat panels Extension gets installers off of their knees Screws available to meet ANSI standards
PROCGB System
Applications: Fiber-cement siding, cement backerboard Slim profile allows driving in corners Drives fasteners that meet ANSI standards Compact body for reduced weight and easy handling Details, page 143
PROCGB
PROLDH
PRO200S
CB3BLG Screw
Cement board, C-3 mechanicallygalvanized coating, meets ANSI standards, page 169
PROLDH System
1 14" 2"
1 14", 1 58"
1 14", 1 58"
Applications: Cement backerboard, fiber-cement siding Slim profile allows driving in corners Compact body for reduced weight and easy handling Details, page 144
MTH Screw
Wood underlayment, gray-phosphate or yellow-zinc coating, page 169
1", 1 14"
1", 1 14"
DWC Screw
Gypsum panel to wood, grayphosphate, yellow-zinc or N2000 galvanized coating, page 170
PRO200S Attachment
1" 2"
Applications: Cement backerboard, fiber-cement siding Slim profile allows driving in corners Compact body for reduced weight and easy handling Details, page 143
These coated fasteners possess a level of corrosion resistance that makes them suitable for use in some exterior and corrosive environments and with some preservative-treated woods. For applications in higher-exposure applications, consider type-300 series stainless-steel fasteners for superior corrosion resistance. See pages 10-13 for additional important information before selecting a fastener for a specific application.
DWF Screw
Gypsum panel to steel, grayphosphate coating, page 170
1 14", 1 58"
1 14", 1 58"
1 14", 1 58"
1 14", 1 58"
CB3BLGHL Screw
Fiber-cement board, C-3 mechanicallygalvanized coating, page 169
1 14", 1 58"
1 14", 1 58"
129
Quik Drive PROHSD auto-feed fastening systems are a time-saving solution for truck and trailer manufacturing because the extension enables stand-up driving and our self-drilling screws eliminate the need to pre-drill. Recommended for truck bed and trailer flooring Pre-drilling and fastening combined in one operation reduces labor costs Increases comfort and productivity
PROHSD60 System
PROHSD60 System
45 60mm
45, 60mm
60, 75mm
PROHSD75 System
TBG Self-Drilling Screw
55 75mm
Applications: Wood to steel or aluminum channeling, flatbed trailers, enclosed cargo/utility trailers Specifically engineered for trailer construction Expanded depth settings for various material thickness Broad nose increases stability, protects surfaces Details, page 150
45, 60mm
60, 75mm
TB Self-Drilling Screw
#4 drill point, yellow-zinc coating, page 181
45, 60mm
60, 75mm
These coated fasteners possess a level of corrosion resistance that makes them suitable for use in some exterior and corrosive environments and with some preservative-treated woods. For applications in higher-exposure applications, consider type-300 series stainless-steel fasteners for superior corrosion resistance. See pages 10-13 for additional important information before selecting a fastener for a specific application. 130
Applications: Wood to steel or aluminum channeling, flatbed trailers, enclosed cargo/utility trailers Specifically engineered for trailer construction Expanded depth settings for various material thickness Broad nose increases stability and protects surfaces Details, page 149
PROHSD60
PROHSD75
Quik Drive auto-feed screw driving systems save time when building crates because they enable accurate screw placement and hands-free fastener advancement. Fast, precise and consistent screw driving Precise depth settings help prevent wood splitting Reduces labor, waste and expense Screws provide greater withdrawal strength than nails for stronger, more durable crates
PRO300S System
PRO250 System
1 12" 2 12"
Applications: Crating, fiber-cement siding, wood underlayment, subfloor/sheathing Expanded depth settings for high-density materials Uniform toenailing and countersink on slick surfaces Reversible and replaceable non-skid teeth attachment Details, page 139
PRO250
PRO300S
2", 2 12"
2", 2 12"
PRO300S System
1 12" 3"
Applications: Crating, decks/docks, subfloor, wall plates, stair treads, fiber-cement siding to steel Expanded depth settings for high-density materials Reversible and replaceable non-skid teeth attachment Uniform toenailing and countersink on slick surfaces Sure-grip guide tube increases stability for a broad range of screws Details, page 140
1 34"
1 34"
For information on corrosion, materials and coatings, see pages 10-13. 131
Quik Drive auto-feed screw driving systems are ideal for truss-ply fastening because the extension enables stand-up-and-drive installation and the holding power of screws can reduce the number of fasteners required. Ideal for attaching 2- and 3-ply girder trusses Reduces gapping between plies, improving the quality of the girder Technical information available on page 165
PRO300S System
PRO250 System
1 12" 2 12"
PRO250
PRO300S/CCS+
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
Applications: Truss fastening, subfloor/sheathing, fiber-cement siding Expanded depth settings for high-density flooring materials Uniform toenailing and countersink on slick surfaces Reversible and replaceable non-skid teeth attachment Details, page 139
WSNTL SERIES
Twin thread, yellow-zinc coating, pages 162-165
2 12"
2 12", 3"
PRO300S System
1 12" 3"
PROCSS+ System
1" 3"
Applications: Truss fastening, subfloor/ sheathing, wall plates, stair treads, decks/docks, fiber-cement siding Expanded depth settings for high-density materials Reversible and replaceable non-skid teeth attachment Sure-grip guide tube increases stability for a broad range of screws Details, page 140
132
Applications: Truss fastening, subfloor/ sheathing, wall plates, stair treads, decks/docks, fiber-cement siding Expanded depth settings for high-density materials Reversible and replaceable non-skid teeth attachment Sure-grip guide tube increases stability for a broad range of screws Details, page 142
Quik Drive PROHSD auto-feed fastening systems are ideal for wood-to-steel fastening because they hold the screw in place will drilling and our self-drilling screws eliminate the need for pre-drilling. Ideal for fastening wood nailers and ledgers-to-steel beams and columns Pre-drilling and fastening combined in one operation reduces labor costs Increases comfort and productivity
PROHSD60 System
PROHSD60 System
45 60mm
Applications: Wood to steel Specifically engineered for fastening wood-to-steel Expanded depth settings for various material thickness Broad nose increases stability and protects surfaces Details, page 149
PROHSD60
PROHSD75
45, 60mm
60, 75mm
PROHSD75 System
55 75mm
TB Self-Drilling Screw
Yellow-zinc coating, page 181
45, 60mm
60, 75mm
Applications: Wood to steel Specifically engineered for fastening wood-to-steel Expanded depth settings for various material thickness Broad nose increases stability and protects surfaces Details, page 150
45, 60mm
60, 75mm
These coated fasteners possess a level of corrosion resistance that makes them suitable for use in some exterior and corrosive environments and with some preservative-treated woods. For applications in higher-exposure applications, consider type-300 series stainless-steel fasteners for superior corrosion resistance. See pages 10-13 for additional important information before selecting a fastener for a specific application.
133
QUIK DRIVE Systems and Attachments QUIK DRIVE ADJUSTABLE COUNTERSINK FEATURE
The adjustable countersink on Quik Drive auto-feed attachments allows the user to dial-in fastener penetration to match the material and application. Once the countersink depth is set the driver bit automatically disengages from the head of the screw when the desired penetration is achieved, preventing over-driving. Screws can be driven to the right depth every time without the user having to slow down to check each fastener, making for faster work and more consistent results. Some things to consider when using the countersink feature: Test and adjust the countersink depth using a scrap piece of lumber Stainless-steel screws are softer than carbon steel screws, therefore care should be taken to set the countersink adjustment wheel to a depth that will not over drive the screw during installation. Overdriving stainless-steel screws can cause breakage.
Applications Suboor and Sheathing Decks/Docks Drywall Fiberglass Backed Gypsum Sheathing Fiber-Cement Siding Tile Roong Metal Roong and Siding Steel Framing Steel Decking Steel Stitching Underlayment and Flooring Truck and Trailer Beds Remodeling and General Purpose
2500 rpm BETTER BEST GOOD GOOD BEST BEST BEST BEST GOOD GOOD BEST GOOD BEST
3500 rpm BEST BETTER BETTER BETTER GOOD BETTER BETTER GOOD BETTER BETTER
Many variables such as the material being fastened, user skill level and weather conditions can affect screwdriver performance for a given application. 135
Description*
DeWalt 2500 rpm 6.5 amp 132 in/lbs peak torque* Multi-application versatility
Hitachi 1700 rpm 6.6 amps 215 in/lbs peak torque* Increased power for high-torque applications HIW8VB2
Makita 2500 rpm 6.5 amp 133 in/lbs peak torque* Multi-application versatility
Makita 3500 rpm 6.5 amp 107 in/lbs peak torque* Increased speed for low-torque applications MA6828
Makita 4500 rpm 6.5 amp 89 in/lbs peak torque* High speed for low-torque applications MA6824
Features
DW276QD
MA6823
*This information provided by screwdriver motor manufacturers. All screwdriver motors may also be purchased separately using the tool model number.
136
Description*
Makita 2500 rpm 6 amp Adjustable torque* 6 torque settings, ideal for steel-framing applications MAFS2701
Makita 1000-2000 rpm 4.6 amp (2 speeds) 177 in/lbs peak torque* 2 speeds for heavy-gauge steel applications MA6807Z
Milwaukee 2500 rpm 6.5 amp 120 in/lbs peak torque* Multi-application versatility
Milwaukee 4000 rpm 6.5 amp 77 in/lbs peak torque* Increased speed for low-torque applications MW6742
Features
Increased torque
MABTD141
MW6790
PROPP150G2MATK PROHX516MATK
PROHSD60MVK PROHSD75MVK
PROPP150GMI18K
*This information provided by screwdriver motor manufacturers. All screwdriver motors may also be purchased separately using the tool model number.
MAFS6200
137
PRO200 System
FEATURES:
Compact body for reduced weight and easy handling Slim profile allows driving in corners Smooth nose will not mar drywall surface Limited lifetime warranty on attachment and extension, 1 year limited warranty on screwdriver motors (see specific manufacturers warranty for more information)
APPLICATIONS:
Drywall to wood or steel
For longer drywall screws (1 78" 2 14") see the PRO250DW attachment on page 152.
SYSTEM
OPTIONS DeWalt 2500 rpm screwdriver motor Makita 2500 rpm screwdriver motor
PRO200
Makita 4500 rpm screwdriver motor Attachment only Replacement attachment mandrel
For more information on screwdriver motors and RPM recommendations per application, see pages 135-136.
1" 2"
DWC DWCG DWHL DWF DWFSD
page 170 page 170 page 170 page 170 page 171
Each system includes an auto-feed attachment, an extension, screwdriver motor, screw quiver and a rugged toolbox.
138
PRO250 System
FEATURES:
Non-skid teeth increase stability
Expanded depth settings for high-density flooring materials Reversible replaceable non-skid teeth attachment Uniform toenailing and countersink on slick surfaces Limited lifetime warranty on attachment and extension, 1 year limited warranty on screwdriver motors (see specific manufacturers warranty for more information)
APPLICATIONS:
Uniform toenailing and countersink on slick surfaces
Subfloor to wood or steel Decking on decks and docks Fiber-cement siding to steel
SYSTEM OPTIONS DeWalt 2500 rpm screwdriver motor Makita 2500 rpm screwdriver motor Makita 3500 rpm screwdriver motor Makita 4500 rpm screwdriver motor Milwaukee 2500 rpm screwdrive motor Milwaukee 4000 rpm screwdrive motor Attachment only Replacement attachment mandrel
MODEL NUMBER PRO250G2D25K PRO250G2M25K PRO250G2M35K PRO250G2M45K PRO250G2MW25K PRO250G2MW40K QDPRO250G2 PMANDREL75
1 12" 2 12"
DCL Composi-Lok DTHQ DWFSD DWC PPSD11516S PHSS WSC WSHL WSNTL WSNTLG CBSDQ158S WSFLRV
page 161 page 160 page 171 page 170 page 167 page 167 page 166 page 166 page 162 page 162 page 182 page 180
For more information on screwdriver motors and RPM recommendations per application, see pages 135-136.
Each system includes an auto-feed attachment, an extension, screwdriver motor, screw quiver and a rugged toolbox. 139
FEATURES:
Expanded depth settings for high-density flooring materials Reversible and replaceable non-skid teeth Uniform toenailing and countersink on slick surfaces Sure-grip guide tube increases stability for a broad range of screws Limited lifetime warranty on attachment and extension, 1 year limited warranty on screwdriver motors (see specific manufacturers warranty for more information)
APPLICATIONS:
The decking nose clip positions the screw on the deck board and centers it on the joist for an easy, uniform installation from a standing position.
Decking on decks and docks Subfloor to wood or steel Wall plates, stair treads, sheathing Fiber-cement siding to steel
SYSTEM OPTIONS DeWalt 2500 rpm screwdriver motor Makita 2500 rpm screwdriver motor Makita 3500 rpm screwdriver motor MODEL NUMBER PRO300SM25K PRO300SM35K PRO300SMW25K PRO300SMW40K QDPRO300SG2 PMANDREL75
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
PRO300SD25K
PRO300S
Milwaukee 2500 rpm screwdriver motor Milwaukee 4000 rpm screwdriver motor QDPRO300SG2 Attachment only
1 12" 3"
CBSDQ DCL Composi-Lok DDX Dexxter DHPD DTHQ SS3DSC SSDTH WSNTLG
page 182 page 161 page 162 page 160 page 160 page 160 page 161 page 162
For more information on screwdriver motors and RPM recommendations per application, see pages 135-136.
Each system includes an auto-feed attachment, an extension, screwdriver motor, screw quiver and a rugged toolbox. 140
This Combo System also includes a PRO200G2 attachment for added versatility (also sold separately)
FEATURES:
Non-skid teeth are reversible and replaceable
Expanded depth settings for high-density flooring materials Reversible and replaceable non-skid teeth Uniform toenailing and countersink on slick surfaces Sure-grip guide tube increases stability for a broad range of screws Limited lifetime warranty on attachment and extension, 1 year limited warranty on screwdriver motors (see specific manufacturers warranty for more information) Subfloor to wood or steel Wall plates, stair treads, sheathing Decking on decks and docks Fiber-cement siding to steel
SYSTEM OPTIONS DeWalt 2500 rpm screwdriver motor Makita 2500 rpm screwdriver motor Makita 3500 rpm screwdriver motor Makita 4500 rpm screwdriver motor Milwaukee 2500 rpm screwdriver motor Milwaukee 4000 rpm screwdriver motor QDPRO300SG2 Attachment only PRO200G2 Attachment only Replacement QDPRO300SG2 attachment mandrel Replacement QDPRO200G2 attachment mandrel MODEL NUMBER PROSDDD25K PROSDDM25K PROSDDM35K PROSDDM45K PROSDDMW25K PROSDDMW40K QDPRO300SG2 QDPRO200G2 PMANDREL75 PMANDREL65
APPLICATIONS:
Sure-grip guide tube increases stability for a broad range of screws
PROSDD
1" 3"
CBSDQ DCL Composi-Lok DDX Dexxter DHPD DTHQ PPSD11516S PHSS SS3DSC SSDTH WSC WSFLRV WSHL WSNTL WSNTLG
page 182 page 161 page 162 page 160 page 160 page 167 page 167 page 160 page 161 page 166 page 180 page 166 page 162 page 162
For more information on screwdriver motors and RPM recommendations per application, see pages 135-136.
Each combo system includes two auto-feed attachments, an extension, screwdriver motor, screw quiver and a rugged toolbox. 141
This combo system also includes a QDPRO200SG2 attachment for added versatility (also sold separately) Non-skid teeth are reversible and replaceable
FEATURES:
Expanded depth settings for high-density flooring materials Reversible and replaceable non-skid teeth Uniform toenailing and countersink on slick surfaces Sure-grip guide tube increases stability for a broad range of screws Limited lifetime warranty on attachment and extension, 1 year limited warranty on screwdriver motors (see specific manufacturers warranty for more information)
APPLICATIONS:
Subfloor to wood or steel Wall plates, stair treads, sheathing Decking on decks and docks Fiber-cement siding to steel
SYSTEM OPTIONS DeWalt 2500 rpm screwdriver motor
1" 3"
CBSDQ DCL Composi-Lok DDX Dexxter DHPD DTHQ PPSD11516S MTH PHSS SS3DSC SSDTH WSC WSFLRV WSHL WSNTL WSNTLG
142
page 182 page 161 page 162 page 160 page 160 page 167 page 169 page 167 page 160 page 161 page 166 page 180 page 166 page 162 page 162
PROCCS+
Makita 2500 rpm screwdriver motor QDPRO300SG2 Attachment only QDPRO200SG2 Attachment only Replacement attachment mandrel
For more information on screwdriver motors and RPM recommendations per application, see pages 135-136.
Each combo system includes two auto-feed attachments, an extension, screwdriver motor, screw quiver and a rugged toolbox.
This combo system also includes a QDPRO200SG2 attachment for added versatility (also sold separately)
FEATURES:
QDPROLDHG2 attachment is ideal for cement board and ber-cement board underlayment and backerboard QDPRO200SG2 attachment is ideal for gypsum panel Extension allows stand-up driving and gets installers off of their knees Compact body for reduced weight and easy handling Limited lifetime warranty on attachment and extension, 1 year limited warranty on screwdriver motors (see specific manufacturers warranty for more information)
APPLICATIONS:
Cement board and ber-cement board underlayment to wood or steel Backerboard to wood or steel Gypsum panel to wood or steel
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
SYSTEM
PROLDH
Each combo system includes two auto-feed attachments, an extension, screwdriver motor, screw quiver and a rugged toolbox. 143
PROLDH System
FEATURES:
Slim profile allows driving in corners Drives fasteners that meet ANSI standards Compact body for reduced weight and easy handling Limited lifetime warranty on attachment and extension, 1 year limited warranty on screwdriver motors (see specific manufacturers warranty for more information)
APPLICATIONS:
Cement board and fiber-cement board underlayment/ backerboard to wood or steel
Makita 2500 rpm screwdriver motor PROLDH Attachment only Replacement attachment mandrel page 169 page 169
For more information on screwdriver motors and RPM recommendations per application, see pages 135-136.
Each system includes an auto-feed attachment, an extension, screwdriver motor, screw quiver and a rugged toolbox.
144
SYSTEM
OPTIONS
MODEL NUMBER
PROPP150 System
FEATURES:
The innovative Precision Placement nosepiece allows for easy location of the hole in the roofing panel clip to drive the screw
Innovative Precision Placement nosepiece allows for easy location of the holes in standing seam metal roong clips Also safely and efciently performs steel deck fastening and stitching Auto-feed mechanism provides hands-free screw advancement, eliminating handling of individual screws, cutting installation time in half Collated fastener strips virtually eliminate fastener waste and prevent damage to roof panels from dropped fasteners. Screws available in 4 head styles with 2 levels of corrosion resistance Limited lifetime warranty on attachment and extension, 1 year limited warranty on screwdriver motors (see specific manufacturers warranty for more information)
APPLICATIONS
The PROPP150 also drives hex-head fasteners for steel decking and stitching
Panel clips for standing-seam roong (suitable for panel clips up to 2 12" tall) Steel decking to structural steel members and stitching of steel panels at the edges (side lap stitching) Panel anges for snap-and-seam metal roong
SYSTEM OPTIONS Makita 2500 rpm screwdriver motor Makita 2500 rpm adjustable-torque screwdriver motor
4" 1 12"
page 179 page 172 page 172 page 172
PROPP150
Makita 2500 rpm impact driver Attachment only Replacement attachment mandrel Replacement hex bit and mandrel
For more information on screwdriver motors and RPM recommendations per application, see pages 135-136. System includes mandrels for driving recessed and 516 hex bits.
7
8" 1 12"
page 176
X Screw
Each system includes an auto-feed attachment, screwdriver motor, screw quiver and a rugged toolbox.
145
BGP300 System
FEATURES:
Patented belt collation enables auto-feed fastening of screws with EPDM-backed washers (U.S. Patent 6,783,001) Profile guide on nosepiece ensures uniform screw placement The extension enables stand-up fastening on roofs Depth control prevents over-driving Designed to eliminate skipped screws, reducing screw waste (patent pending) Easy loading keeps work moving Screws available in 21 colors to match popular roofing-panel colors
The prole guides match the panel-ridge proles with feet that rest on the at portion of the panel. This centers the screw on the ridge for a uniform look and a better fastener seal.
The locking depth control seats the washer on the fastener and helps prevent overdriving (as shown above) that can damage metal roong and siding.
APPLICATIONS:
Exposed-fastener metal roofing to wood Metal siding to wood
DESCRIPTION Attachment, 16" extension, (1) flat profile guide, (1) AG panel/ 34" rib profile guide MODEL NUMBER QDBGP300G2K BPHXLBBGP14G2 BPHXLBBGP516G2
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
SYSTEM
BGP300
3
Replacement attachment mandrel with 4" hex bit Replacement attachment mandrel with 16" hex bit
4" 3"
page 174 page 174 page 174 page 174
For more information on screwdriver motors and RPM recommendations per application, see pages 135-136.
The BGP300 system includes: Auto-feed attachment 2 prole guides (at and AG Panel) 2 lobular hex-head driver bits (14" and 516") 16" extension Belt hook fastener-strip holder Rugged tool box The BGP300 does not include a screwdriver motor.
146
PRORF System
QDPRORFG2 Attachment (also sold separately) Visibility window allows precise visual placement of screws
FEATURES:
Precision depth settings prevent tile breakage Window in guide tube provides visibility to allow exact screw placement Drives fasteners meeting code requirements Limited lifetime warranty on attachment and extension, 1 year limited warranty on screwdriver motors (see specific manufacturers warranty for more information)
APPLICATIONS:
Roofing tiles to wood
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
SYSTEM
1 12" 2 12"
WSCD WSCT SSWSCB page 171 page 171 page 171
PRORF
Makita 3500 rpm screwdriver motor Attachment only Replacement attachment mandrel
For more information on screwdriver motors and RPM recommendations per application, see pages 135-136.
Each system includes an auto-feed attachment, screwdriver motor, screw quiver and a rugged toolbox.
147
PRO300SRF System
FEATURES:
Precision depth settings prevent tile breakage Window in guide tube provides visibility to allow exact screw placement Drives fasteners meeting code requirements Limited lifetime warranty on attachment and extension, 1 year limited warranty on screwdriver motors (see specific manufacturers warranty for more information)
APPLICATIONS:
Roofing tiles to wood
DRIVE THESE COLLATED SCREWS SYSTEM OPTIONS Makita 2500 rpm screwdriver motor
2 2" 3"
WSCD WSCT SSWSCB page 171 page 171 page 171
PRO300SRF
Makita 3500 rpm screwdriver motor Attachment only Replacement attachment mandrel
For more information on screwdriver motors and RPM recommendations per application, see pages 135-136.
Each system includes an auto-feed attachment, screwdriver motor, screw quiver and a rugged toolbox. 148
PROHSD60 System
FEATURES:
Slim profile allows driving in corners Compact body for reduced weight and easy handling Limited lifetime warranty on attachment and extension, 1 year limited warranty on screwdriver motors (see specific manufacturers warranty for more information)
APPLICATIONS:
Truck beds and trailer flooring to steel Wood nailers to structural steel
SYSTEM
OPTIONS Hitachi 1700 rpm screwdriver motor Makita 10002000 rpm screwdriver motor
PROHSD60
Makita 2500 rpm screwdriver motor Attachment only Replacement attachment mandrel
For more information on screwdriver motors and RPM recommendations per application, see pages 135-136. For applications where maximum torque is preferred, see the Hitachi screwdriver motor HIW8VB2 on page 136 (sold separately).
Each system includes an auto-feed attachment, an extension, screwdriver motor, screw quiver and a rugged toolbox. 149
PROHSD75 System
FEATURES:
Slim profile allows driving in corners Compact body for reduced weight and easy handling Limited lifetime warranty on attachment and extension, 1 year limited warranty on screwdriver motors (see specific manufacturers warranty for more information)
APPLICATIONS:
Truck beds and trailer flooring to steel Wood nailers to structural steel
SYSTEM
MODEL NUMBER
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
PROHSD75
Makita 10002000 rpm screwdriver motor Attachment only Replacement attachment mandrel
For more information on screwdriver motors and RPM recommendations per application, see pages 135-136. For applications where maximum torque is preferred, see the Hitachi screwdriver motor HIW8VB2 on page 136 (sold separately).
Each system includes an auto-feed attachment, an extension, screwdriver motor, screw quiver and a rugged toolbox. 150
PROHX516 System
FEATURES:
Precise depth adjustment prevents over and under driving Compact body for reduced weight and easy handling Limited lifetime warranty on attachment and extension, 1 year limited warranty on screwdriver motors (see specific manufacturers warranty for more information)
APPLICATIONS:
Cold-formed steel framing Steel decking to structural steel members
DRIVE THESE COLLATED SCREWS
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
SYSTEM
8" 1"
page 176
PROHX516
Makita 2500 rpm adjustable torque screwdriver motor Attachment only Replacement attachment mandrel
X Screw
For more information on screwdriver motors and RPM recommendations per application, see pages 135-136. For applications where maximum torque is preferred, see the Hitachi screwdriver motor HIW8VB2 on page 136 (sold separately).
Each system includes an auto-feed attachment, an extension, screwdriver motor, screw quiver and a rugged toolbox.
151
4" 1"
page 179 page 178 page 177
FEATURES:
DESCRIPTION Attachment Only Replacement Mandrel Noseguard MODEL NO. QDPROPHG2 PMANDREL65 PNOSEGUARD-5
Compact body for reduced weight and easy handling Slim profile allows driving in corners Tough reliability for targeted applications For use with any Quik Drive G2-equipped screwdriver motor Limited lifetime warranty
178" 212"
DWC DWHL DWFSD page 170 page 170 page 171
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
FEATURES:
Compact body for reduced weight and easy handling Slim profile allows driving in corners Smooth nose will not mar the drywall surface For use with any Quik Drive G2-equipped screwdriver motor Limited lifetime warranty
152
1" 158"
DWFSD DWCG page 171 page 170
DESCRIPTION Attachment Only Includes adaptors for: DeWalt, Makita, Milwaukee screwdriver motors Replacement Mandrel
MODEL NO.
QDA158NS
FEATURES:
Compact body for reduced weight and easy handling Equipped with non-skid teeth for stability Slim profile allows driving in corners Snaps onto DeWalt, Makita, or Milwaukee screwdriver motor 90 day warranty
PMANDREL158
153
MODEL NUMBER
QDHANDLE PADJARMBGP300G2 BITKEY BIT2P-RC3 BIT2S-RC3 BIT2SU-RC3 BIT3S-RC3 BIT3SU-RC3 BIT2P-RC10 BIT2S-RC10 BIT2SU-RC10 BIT3S-RC10 BIT3SU-RC10 TOOLCASE-LG QDDECKCLIP-RC BITHEX516 BITHEXLB516 BITHEXLB14 QDEXTG2-16 QDEXTG2 QDEXTG2-22 QDEXTG2-T G2HANDLE PFEEDPAWL PFEEDPAWLTL PFEEDPAWL3 PFEEDPAWL2 QDLEAFSPRING QDLEAFSPRING2 PMANDREL158 BPHXLBBGP14G2 BPHXLBBGP516G2 PNOSECLIP PNOSEGUARD-S PMANDREL55 PMANDREL6 PMANDREL65-RC PMANDREL75-RC PMANDREL10 BPHXLBPPG2 BPHX516G2 PPROFILEGUIDE5V PPROFILEGUIDE32 PPROFILEGUIDE22 PPROFILEGUIDE23 PPROFILEGUIDE11 PPROFILEGUIDE33 PPROFILEGUIDE34 QUIVER
PFEEDPAWL
BIT3S-RC10
QDDECKCLIP-RC
DRIVE TYPE/SIZE #2 square drive #2U (#2 undersized) #3 square drive #3U (#3 undersized) #2 phillips
1
BIT
R2
DESCRIPTION BIT2S for most screws with #2 recess and interior-grade coating BIT2SU for most screws with #2 recess and exterior-grade coating BIT3S for most screws with #3 recess and interior-grade coating BIT3SU for most screws with #3 recess and exterior-grade coating BIT2P for all Quik Drive screws with phillips recess BITHEXLB14 For most screws with 14" lobular hex drive BITHEXLB516 For most screws with 516" lobular hex drive
R2U
R3
R3U
P2
154
SCHEMATIC
ATTACHMENT
Depth Adjustment Wheel G2 Locking Lever NOSE PIECE GUIDE TUBE HEX MANDREL (found inside attachment) Part No.: BPHXLBBGP14G2 Attachment: QDBGP300G2K BPHXLBBGP516G2 Attachment: QDBGP300G2K BPHX516G2 Attachment: QDPROHX516G2 BPHXLBPPG2 Attachment: QDPROPP150G2 PMANDREL10 Attachment: QDPROPP150G2 PMANDREL65 Attachments: QDPRO200G2, QDPROLDHG2, QDPROPHG2 PMANDREL75 Attachments: QD200SG2, QDPRO250G2, QDPRO300SG2, QDPRORFG2, QDPRO300SRFG2, QDHSD60, QDHSD75, QD2000SDS PMANDREL158 Attachments: QDA158G2, QDA158NS Nose Bit Release Slot Bit MANDREL (found inside attachment)
Screw Release Lever Feed Pawl Lever (Must be engaged in Feed Pawl Assembly Slot) Feed Pawl Assembly
QD ADAPTOR MIAG2
QD ADAPTOR MIL65G2 MIAG2 MIAG2 MIAG2 MIAG2 MIAG2 MIAG2 MIAG2 MIAG2 MIAG2 MIAG2 MIAG2 MIAG2 MIAG2 MIAG2 MIAG2 MIAG2 MIAG2
SE4000 ATLAS COPCO PRO2000 BOSCH 1423VSR 1404VSR 1405VSR GSR625TE GSR640TE GSR645TE SG25 SG45 CHICAGO PNEUMATIC RP2780 DEWALT 252 254 255 257 260 265 266 267 268 272 274 275 520 969
1
MIAG2
WH18DMR MAKITA
MAA6807G2 MAAG2 MAAG2 MAAG2 MAAG2 MAAG2 ADM27G2 MAAG2 ADM31DG2 ADM31DG2 ADM34G2 ADM34G2 ADM31DG2 ADM31DG2 MAA2G2 MAA1G2 MAA1G2 MAA1G2 MAA4G2 MAA3G2 MAA3G2 MAA3G2
6702-20 6740-20 6741-1 6742-20 6743-20 6743-50 6743-55 6745-1 6746-1 6755-4 6758 6760 6790-1 6791-20 PORTER CABLE 4630 4634 4640 SIOUX 2P2603A 2P2303A 2S2303A 2P2603AQ
CPAG2
6833D 6834
DWAG2 DWAG2 DWAG2 DWAG2 DWAG2 DWAG2 DWAG2 DWA3G2 DWA3G2 DWAG2 DWAG2 DWAG2 DWA1G2 DWA3G2 DWA2G2
6835D FR440D BFR750 BFS450 BTD141 BTD142HW BTD144 FS2701 FS2200 FS4200 FS6200 MASTERPOWER 2460-M 2461-M METABO SE 5025
MPAG2 MPAG2
HILTI
SSD10P20PS
Quik Drive collated screws combine performance with ease of installation for a variety of residential, commercial and industrial applications.
High-quality fasteners that are extensively tested to ensure optimum performance in their target applications Quik Drive screws are specifically designed for use in our attachments to ensure problem-free system performance The patented curved collation strips (U.S. Patent 7,051,875) hold the screws up and away from the work surface, making moving and positioning the tool easier. They are also pointed on the inserted end to simplify loading.
157
161 161 161 161 161 161 161 161 162 162 162 162 162 162 162 162 160 160 160 160 160 160 160 161 161 160 161 161 161 166 162 162 162 162 162 162 162 166 166 166 166 162 162 162 162 162 167 167 167 169 169 169 169 169 169 182 182 171 171 171 171 171 167 167 162 162
158
DRYWALL DWC1PS 170 DWC114PS 170 DWC158PS 170 DWC2PS 170 DWC212PS 170 DWCZ114PS 170 DWCZ158PS 170 DWCZ2PS 170 DWF1PS 170 DWF114PS 170 DWF158PS 170 DWFSD114PS 171 DWFSD158PS 171 DWFSD178PS 171 DWFSD238PS 171 DWFSDG114PS 171 DWHL178PS 170 METAL ROOFING / SIDING-TO-WOOD/STEEL PC1BS1012 172 PC1BS1211 172 PCQ1BS1012 172 PCQ1BS1211 172 PCQ112BS1012 172 SSPC1BS1012 172 PCSD1S1016 172 PCSD1S1214 172 PCSDQ1S1016 172 PCSDQ1S1214 172 SSPCSD1S1016 172 PCULP1BS1012 172 PCULP112BS1012 172 PCULPQ1BS1012 172 PCULPQ112BS1012 172 SSPCULP1BS1012 172 HG112WT10 174 HG2WT10 174 HJ1WT10 174 HJ112WT10 174 HJ2WT10 174 HJ212WT10 174 HJ3WT10 174 HJ34WT12 174 SSH1WT10 174 SSH112WT10 174 SSH2WT10 174 SSH212WT10 174 XJ1WT14 174 XJ114WT14 174 XJ112WT14 174 XJ2WT114 174 STEEL-TO-STEEL FPHSD34S1016 179 FPHSD34S1214 179 PHSD34S0818 178 TRSD34S1016 177 X1S1016 176 XQ1S1016 176 X1S1214 176 XQ1S1214 176 XQ78S1224 176 XQ114S1224 176 XQ112S1224 176 WOOD-TO-STEEL / ALUMINUM FHSD1S1018 180 FHSD114S0818 180 FHSD212S1214 180 TB1445S 181 TB1460S 181 TB1475S 181 TBG1445S 181 TBG1460S 181 TBG1475S 181 WSF1LRVS 180 WSF134LRVS 180
* * *
* * *
* Drive with PRO200S or QDA158NS only when fastening berglass backed gypsum sheathing panels
159
PRO 300S
SS3DSC Screw
Common Application: Wood decking to wood FEATURES:
Bugle head #3 square drive (Driver bit in each box; replacement bit model BIT3S) Coarse threads Type-17 point Available in types 305 and 316 stainless steel Curved collation
Length (in.) 2 12 2 12 3 3 Shank Size #10 #10 #10 #10 Material Carton Quantity 1500 1500 1000 1000 Model No. PRO 300S
Length Shank Trim head with nibs Fasteners (in.) Size Fasteners for easy countersinking Model No. Model No. per Pack per Pack #2 undersized 2 #8 1000 HCKDTHQ2S 2000 DTHQ2S square drive (Driver bit in each 1 2 2 #8 750 HCKDTHQ212S 1500 DTHQ212S box; replacement bit model BIT2SU) 3 #8 500 HCKDTHQ3S 1000 DTHQ3S Coarse threads Type-17 point Quik Guard coating Curved collation This screw is also available in bulk for hand-drive installation. See page 86 for details. For information on corrosion, materials and coatings, see pages 10-13.
PRO 200
PRO 200S
PRO 250
PRO 300S
160
These coated fasteners possess a level of corrosion resistance that makes them suitable for use in some exterior and corrosive environments and with some preservative-treated woods. For applications in higher-exposure applications, consider type-300 series stainless-steel fasteners for superior corrosion resistance. See pages 10-13 for additional important information before selecting a fastener for a specific application.
Brown Gray Tan White (Various color versions similar) Contractor Pack Fasteners per Pack 2000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 Model No. SSDTH2S SSDTH212SBR02 SSDTH212SBR03 SSDTH212SBR04 SSDTH212SGR02 SSDTH212SGR03 SSDTH212STN02 SSDTH212STN03 SSDTH212SWH01 SSDTH212SWH02 SSDTH212S SSDTH3S PRO 250 PRO 300S
Retail Pack Head Color Fasteners per Pack Unpainted Brown 02 Brown 03 Brown 04 Gray 02 Gray 03 Tan 02 Tan 03 White 01 White 02 Unpainted Unpainted 500 500 500 Model No. HCKSSDTH2S HCKSSDTH212S HCKSSDTH3S
#7 #7 #7 #7 #7 #7 #7 #7 #7 #7 #7 #7
Composi-Lok Screw
Common Application: Composite decking to wood FEATURES:
Cap head #2 undersized square drive. Driver bit in each box; replacement bit model BIT2SU (BIT2S for stainless steel versions) Wings on shaft help prevent screw spinout Sharp point Quik Guard coating Available in 4 colors and type 305 stainless steel (see table) Curved collation This screw is also available in bulk for hand-drive installation. See page 95 for details.
Length Shank (in.) Size 2 12 2 12 2 12 2 2 2 2 3 3 3 3 3
1 1
Gray
Contractor Pack Fasteners per Pack 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 Model No. DCLB212S DCLG212S DCLR212S DCLT212S SSDCL212S DCLB3S DCLG3S DCLR3S DCLT3S SSDCL3S
Color Brown Gray Red Tan Type 305 Stainless Brown Gray Red Tan Type 305 Stainless
Fasteners per Pack 500 500 500 500 500 500 500 500 500 500
Model No. HCKDCLB212S HCKDCLG212S HCKDCLR212S HCKDCLT212S HCKSSDCL212S HCKDCLB3S HCKDCLG3S HCKDCLR3S HCKDCLT3S HCKSSDCL3S
#9 #9 #9 #9 #9 #9 #9 #9 #9 #9
For information on corrosion, materials and coatings, see pages 10-13. These coated fasteners possess a level of corrosion resistance that makes them suitable for use in some exterior and corrosive environments and with some preservative-treated woods. For applications in higher-exposure applications, consider type-300 series stainless-steel fasteners for superior corrosion resistance. See pages 10-13 for additional important information before selecting a fastener for a specific application.
161
WSNTL Screw
Common Applications: Subfloor and sheathing to wood Decking to wood Ply fastening for multi-ply trusses FEATURES:
Flat head with nibs for easy countersinking #3 square drive (Driver bit in each box; replacement bit model BIT3S) Twin threads Sharp point (except WSNTL2LS-17 has a type-17 point) Curved collation 2" length recommended by Huber for Advantech flooring
Advantech is a registered trademark of Huber Engineered Woods.
#3 Drive Type
Yellow-Zinc Coating 1 4 2 2 2 12 3
3
#8 #8 #8 #8 #8
Quik Guard Coating 1 34 2 2 12 3 #8 #8 #8 #8 Undersized Undersized Undersized Undersized 2000 2000 1500 1000 WSNTLQ134S WSNTLQ2S WSNTLQ212S WSNTLQ3S
#8 #8 #8
Available Coatings: Yellow zinc, Quik Guard and Class 55 Mechanically Galvanized (meets ASTM B695, Class 55, compliant with the 2006 International Residential Code , section R319.3 and the 2009 International Residential Code, section R317.3) Codes/Standards: ICC-ES ESR-1472; City of L.A. RR25661; Florida FL 13731 (Note: 1 34" length not code listed)
For information on corrosion, materials and coatings, see pages 10-13. These coated fasteners possess a level of corrosion resistance that makes them suitable for use in some exterior and corrosive environments and with some preservative-treated woods. For applications in higher-exposure applications, consider type-300 series stainless-steel fasteners for superior corrosion resistance. See pages 10-13 for additional important information before selecting a fastener for a specific application.
162
1. Use the lower of the pull-through or withdrawal values to determine axial design value. 2. Screws must be installed straight into the side grain of the wood main member with the screw axis at a 90 angle to the wood bers. 3. The main framing member must be wood having a minimum specic gravity of 0.50 for DFL and SP main members, and 0.42 for SPF and HF main members. DFL is
Douglas Fir-Larch. SP is Southern Pine. SPF is Spruce-Pine-Fir. HF is Hem-Fir. 4. Table based on testing conducted in accordance with AC233. Design values presented are based on average ultimate values and divided by 5. 5. Allowable loads are shown at the wood load duration factor of CD = 1.0. Loads may be increased for load duration up to CD = 1.6.
Allowable Shear (in Pounds per Foot) for Wood Structural Panel Diaphragms with Framing of Douglas Fir-Larch or Southern Pine for Wind or Seismic Loading (2", 212" and 3" Lengths)
Minimum Nominal Panel Thickness (in.) Blocked Diaphragms Unblocked Diaphragms Minimum Screw spacing (inches) at diaphragm boundaries Nominal Width Screws spaced 6 inches, maximum, (all cases), at continuous panel edges parallel to load of Framing at support edges6 (Cases 3 and 4), and at all edges (Cases 5 and 6)6 Members at Adjoining Panel 6 4 2127 27 Case 1 (no unblocked All other Edges and Screw Spacing (inches) at Other Panel Edges edges or continuous configurations 4,5 Boundaries (in.) joints parallel to load) (Cases 2,3,4,5 and 6) 6 6 4 3 2 270 360 530 600 240 180 3 300 400 600 675 265 200 2 320 425 640 730 285 215 3 360 480 720 820 320 240 2 240 320 480 545 215 160 3 270 360 540 610 240 180 2 255 340 505 575 230 170 3 285 380 570 645 255 190 2 290 385 575 655 255 190 3 325 430 650 735 290 215 2 320 421 640 730 285 215 3 360 480 720 820 320 240
5. Framing at adjoining panel edges must be 3 inches nominal or wider, and screws must be staggered where both of the following conditions are met: (1) screws having penetration into framing of more than 1 inches and (2) screws are spaced 3 inches o.c. or less. 6. Space screws maximum 12 inches o.c. along intermediate framing members (6 inches o.c. where supports are spaced 48 inches o.c.). 7. Framing at adjoining panel edges must be 3-inch nominal or wider, and screws must be staggered where screws are spaced 2 inches or 2 inches on center. 8. See ICC-ES ESR-1472 for allowable shear loads for high load diaphragms.
Panel Grade
Structural 1/OSB
15
32 8
Sheathing single floor, and other grades covered in DOC PS1 and PS2
16 32 32
15
19
1. Minimum fastener penetration of 114" into the framing member is required. 2. For wind design, shear capacities may be increased 40% per section 2306.3.2 of the 2006 IBC and 2306.2.1 of the 2009 IBC. 3. For shear loads of normal or permanent load duration as dened by the AF&PA NDS, the values in the table above must be multiplied by 0.63 or 0.56, respectively. 4. The minimum nominal width of framing members not located at boundaries or adjoining panel edges must be 2 inches.
FRAMING LOAD
CASE 1
CASE 2
BLOCKING IF USED
CASE 3
CASE 4
CASE 6
CASE 5
163
Panels Applied Directly to Framing Screw Spacing at Panel Edges (in.) 6 230 4 360 395 510 320 350 460 510 3 460 505 6657 410 450 600 7 665
7
8 1 4
1
16 32 8
15
3 7
16 32 32
15
1 14
19
For SI: 1 inch = 25.4 mm, 1 pound/foot = 0.146 N/mm. 1. For framing of other species: (1) Find specic gravity for species of lumber in 2005 AF&PA National Design Specication (NDS). (2) Find shear value from table above for actual grade and multiply value by the following adjustment factor: Specic Gravity Adjustment Factor = [1-(0.5-SG)], where SG = Specic Gravity of the framing lumber. This adjustment factor must not be greater than 1. 2. For shear loads of normal or permanent load duration as dened by the NDS, the values in the table above must be multiplied by 0.63 or 0.56, respectively. 3. Panel edges backed with 2" nominal or wider framing. Install panels are either horizontally or vertically. Space screws maximum 12" o.c. along intermediate supports. 4. Where panels are applied on both faces of a wall and screw spacing is less than 6" o.c. on either side, panel joints must be offset to fall on different framing members, or framing must be 3" nominal or thicker at adjoining panel edges and screws on each side must be staggered. 5. Values apply to all-veneer plywood. Thickness at point of fastening on panel edges govern shear values. 6. Framing at adjoining panel edges must be 3" nominal or wider, and screws must be staggered where both of the following conditions are met: (1) screws having penetration into framing of more than 112" (2) screws are spaced 3" o.c. 7. Framing at adjoining panel edges must be 3" nominal or wider, and screws must be staggered where screws are spaced 2" or 2" on center. 8. Use of screws as shear wall sheathing fasteners must be permitted only for wind and seismic design in Seismic Design Categories A, B, and C where R = 1.5 and 0 = 2.5.
IRC Equivalent Prescriptive Fastening Schedule (2", 212" and 3" Lengths)
Description of Building Materials Description of Fastener 1 Spacing of Fasteners (in.) Edges Intermediate Supports
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
1 screw (all lengths) 1 screw (all lengths) 1 screw (min. 2 12" length)
6 6 6
12 12 12
19
1 screw (all lengths) 1 screw (all lengths) 1 screw (min. 2 2" length)
1
6 6 6
12 12 12
1. Screws shall be spaced at not more than 6"on center at all supports where spans are 48" or greater. 2. For regions having basic wind speed of 100 mph or less, screws for attaching wood structural panel roof sheathing to gable-end wall framing shall be spaced 6" on center (o.c.) when basic wind speed is greater than 100 mph, screws for attaching panel roof sheathing to intermediate supports shall be spaced 6" o.c. for minimum 48" distance from ridges, eaves and gable end walls, and 4" o.c. to gable-end wall framing. 3. Spacing of fasteners on oor-sheathing-panel edges applies to panel edges supported by framing members and required blocking and at all oor perimeters only. Spacing of fasteners on roof-sheathing-panel edges applies to panel edges supported by framing members and required blocking. Blocking of roof or oor-sheathing-panel edges perpendicular to the framing members need not be provided except as required by other provisions of the code. Floor perimeter shall be supported by framing members or solid blocking.
164
Design Value Comparison of Common Fasteners Used to Attach Truss Plies Together
Shear (lbs.) Fastener Length Diameter (in.) (in.) 2 12 3
5 5
Withdrawal (lbs.) SPF (100) 70 85 69 82 DFL (100) 133 200 44 48 SP (100) 175 263 56 61 SPF (100) 93 140 28 31
3 3
1. Table values are based on attachment of a 1 12" side member to a 1 12" main member of the same species and grade. 2. Table values are based on the 2005 National Design Specications (NDS). Values shall be multiplied by all applicable adjustment factors such as for load duration, etc. (except where noted). 3. Specic Gravities (G) assumed: DFL G = 0.50, SP G = 0.55, SPF G = 0.42. 4. The spacing of applied uniform loads to the multi-ply member shall not exceed 24 inches on center. 5. Assumes collated nail Fyb = 100 ksi. 6. WSNTL212S and WSNTL3S withdrawal values based on testing per AC233.
INSTALLATION:
Screw spacing shall be in accordance with the fastener schedule provided on the Truss Design Drawing or as otherwise approved by the Truss Designer. Screw spacing shall not exceed 12" on center and shall not be less than 3" on center. WSNTL series screws may be installed with the screw heads in either the loaded or unloaded ply. Do not overdrive screws. For 3-ply girder assemblies, the WSNTL screws may be installed from the same side as each ply is applied (no ipping of the truss is required) in accordance with BCSI (2006 edition). Girders that are fastened together at the jobsite must have the fastener heads visible for inspection. Stagger the screws in the 3rd ply a minimum of 1" from the screws installed into the rst 2 plies. Individual screw locations may be adjusted up to 12 of the required screw spacing to avoid conicts with other hardware or to avoid lumber defects. (3" minimum spacing still required.) Use minimum of 3" long fasteners to attach hangers to the girder truss. A 2500 rpm motor is recommended.
2-Ply Assembly
3-Ply Assemblies
" min
1 " min
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
Typical Spacing for WSNTL Screws Truss Plant Installation Jobsite Installation
Ply-To-Ply Connection Comparison for a 30 Ft Long 3-Ply Girder Bottom Chord Loading
Sample bottom chord nailing requirement for 3-ply girder using .120 x 3" collated nails Alternate fastening using WSNTL3S screws
4"o.c.
5"o.c.
Examples based on 3-ply girder spanning 30 ft., 2x6 Southern Pine bottom chords, 825 plf BC load and 1.15 load duration. Nail and screw spacing is repeated for each layer. 165
WSHL134S7 HCKWSHL134S7
WSC Screw
Common Application: Wood to wood FEATURES:
Flat head with nibs for easy countersinking #2 square drive standard and undersized (Replacement bit models BIT2S and BIT2SU) Coarse threads Available with type-17 and sharp points Curved collation Available Coatings: Yellow zinc, N2000 mechanically galvanized
1 34 #8 Sharp Undersized Length Shank (in.) Size Point Type #2 Drive Type Carton Quantity Model No. PRO 200 PRO 200S PRO 250 PRO 300S
#8 #8
Type 17 Sharp
Standard Standard
2500 2000
WSC114S-17 WSC112S
N2000 Coating
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
2000
WSCG134S
WSCLT Screw
Common Application: Wood to wood FEATURES:
Flat head #2 square drive (Driver bit in each box; replacement bit model BIT2S) Coarse threads Sharp point Yellow-zinc coating Curved collation Fully threaded
Length (in.) 1 34 Shank Size #8 Carton Quantity 2000 Model No. PRO 200 PRO 200S PRO 250 PRO 300S
WSCLT134S
For information on corrosion, materials and coatings, see pages 10-13. 166
PHSS2S PHSS212S
PPSD Screw
Common Application: Subfloor/sheathing to cold-formed steel (#8 maximum thickness: 54 mils/16 ga.; #10 maximum thickness: 97 mils/12 ga.) FEATURES:
Flat head with nibs for easy countersinking #3 square drive (Driver bit in each box; replacement bit model BIT3S) Fine threads Pilot point
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
Point Size 2 3 3
Model No.
PRO 200
PRO 200S
PRO 250
PRO 300S
#8 #10 #10
Yellow-zinc coating Curved collation 0.315" head diameter meets AISI lateral design standard Codes/Standards: ASTM C1513 compliant
1. The tabulated values are based on calculations with Section E4 of the AISI S100-07. 2. Values are based on cold-formed steel (CFS) members with a minimum yield strength, F y of 33 ksi and minimum tensile strength, Fu of 45 ksi for 43 mil (18 ga) to 27 mil (22 ga), and a minimum yield strength, F y of 50 ksi and minimum tensile strength, Fu of 65 ksi for 54 mils (16 ga). 3. For design purposes,steel sheet thicknesses are 0.0283" for 27 mil (22 ga), 0.0346" for 33 mil (20 ga), 0.0451" for 43 mil (18 ga), and 0.0566" for 54 mil (16 ga). The actual sheet thickness shall not be less than 95% of these design thickness as specied in AISI/COFS/GP 2001 Section A5.1. 4. A minimum of three exposed screw threads are required to achieve loads in table. 5. See page 183 for information on screw strength.
For information on corrosion, materials and coatings, see pages 10-13. 167
Fastener Spacing at Panel Edges2 (in.) 6 780 890 700 825 940 4 990 1330 915 1235 1410 3 1775 1545 1760 2 2190 2060 2350
2:13 2:1
1. Nominal strength shall be multiplied by the resistance factor ( = 0.6, LRFD) to determine design strength or divided by the safety factor ( = 2.5, ASD) to determine allowable strength. 2. Screws in the eld of the panel shall be installed 12" (305 mm) on center (o.c.) unless otherwise shown. 3. Shear wall height to width aspect ratio (h/w) greater than 2:1, but not exceeding 4:1, shall be permitted provided the nominal strength values are multiplied by 2w/h. 4. Wall studs and track shall be of ASTM A1003 Stuctural Grade 33 (Grade 230) Type H steel for members with a designation thickness of 33 and 43 mils, and A1003 Structural Grade 50 (Grade 340) Type H steel for members with a designation thickness equal to or greater than 54 mils. 5. For wood structural panel sheated shear walls, tabulated Rn values applicable for short-term load duration (seismic loads). For other in-plane lateral loads of normal or permanent load duration as dened by the AF&PA NDS, the values in the table for wood structural panel sheathed shear walls shall be multiplied by 0.63 (normal) or 0.56 (permanent). 6. All sheathing edges shall be attached to framing or 112" width 33 mil blocking. 7. Maximum stud spacing 24" o.c. 8. Table based on Table C2.1-3 AISI Standard North American Standard for Cold-Form Steel Framing-Lateral Design 2007 Edition with Supplement No. 1 and Commentary. 9. See General Load Table on page 183 for screw strength.
3 1425
3
2 18253
1. Nominal strength shall be multiplied by the resistance factor ( = 0.65, LRFD) to determine design strength or divided by the safety factor ( = 2.0, ASD) to determine allowable strength. 2. Screws in the eld of the panel shall be installed 12 inches (305 mm) on center (o.c.). 3 Shear wall height to width aspect ratio (h/w) greater than 2:1, but not exceeding 4:1, shall be permitted provided the nominal strength values are multiplied by 2w/h. 5. For wood structural panel sheathed shear walls, tabulated Rn values applicable
6. 7. 8. 9. 10.
for short-term load duration (wind loads). For other in-plane lateral loads of normal or permanent load duration as dened by the AF&PA NDS, the values in the table above for wood structural panel sheathed shearwalls shall be multiplied by 0.63 (normal) or 0.56 (permanent). Maximum stud spacing 24" o.c. Stud, track and blocking (if applicable) shall be a minimum of 33 mils. All sheathing edges shall be attached to framing or 112" width 33 mil blocking. Table based on Table C2.1-1 AISI Standard North American Standard for Cold-Form Steel Framing-Lateral Design 2007 Edition with Supplement No. 1 and Commentary. See General Load Table on page 183 for screw strength.
Blocked Membrane Material Thickness (in.) Screw Spacing at Diaphragm Boundary Edges and All Continuous Panel Edges (in.) 6 4 2.5 2 Screw Spacing at All Other Panel Edges (in.) 6 6 4 3 768 1022 1660 2045 768 1127 1800 2255 925 1232 1970 2465 690 920 1470 1840 760 1015 1620 2030 832 1110 1770 2215
Unblocked Screws Spaced Maximum of 6" on All Supported Edges Load Perpendicular to Unblocked Edges and Continuous Panel Joints 685 755 825 615 680 740 All Other Configurations 510 565 615 460 505 555
Structural 1
8 16 15 32 3 8 7 16 15 32
7
1. Framing members shall have a designated thickness between 33-54 mils. 2. Wood structural panels shall conform to DOC PS-1 and PS-2. 3. For wood structural panel sheathed diaphragms, tabulated Rn values shall be applicable for short-term load duration (wind or seismic loads). For other in-plane lateral loads of normal or permanent load duration as dened by the AF&PA NDS, the values in the the table above for wood structural panel sheathed diaphragms shall be multiplied by 0.75 (normal) or 0.67 (permanent). 4. Nominal strength shall be multiplied by the resistance factor ( = 0.60, LRFD Seismic, = 0.65, LRFD Wind) or divided by the safety factor ( = 2.5 ASD Seismic, = 2.0 ASD Wind) to determine allowable strength. 5. Length to width ratio of blocked wood diaphragms shall not exceed 4:1 and 3:1 for unblocking diaphragms.
6. Screws installed in the eld of the panel shall be spaced at a maximum of 12" on center (o.c.) 7. Shear values are permitted for use in seismic design where the seismic reponse modication factor, R, taken to or less than 3. 8. Where diaphragms are blocked, all panel edges must be attached to framing or blocking. Blocking shall be a minimum thickness of 33 mils with a minimum width of 112". 9. Maximum joist spacing 24" o.c. 10. Table based on Table D2.1 AISI Standard North American Standard for Cold-Form Steel Framing-Lateral Design 2007 Edition with Supplement No. 1 and Commentary. 11. Screws installed in the eld of the panel shall be installed at 12 o.c. 12. For open-front structures, see AISI standard for additional information. 13. See page 183 for information on screw strength.
168
Nominal Shear Strength (Rn) for Diaphragms with Wood Sheathing2 (lbs/ft)
Retail Pack Coating Fasteners per Pack 1000 Model No. HCKMTH114S
Contractor Pack Fasteners Model No. per Pack 2500 2500 MTHZ1S MTH114S PRO 200 PRO 200S
#7 #7
CB3BLG Screw
Common Application: Fiber-cement board to wood FEATURES:
Retail Pack Contractor Pack Threads 0.375" ribbed wafer Length Shank Per Fasteners Fasteners (in.) Size head with nibs for Model No. Model No. Inch per Pack per Pack easy countersinking 1 14 #10 10 500 HCKCB3BLG114S 1500 CB3BLG114S #3 undersized square drive (Driver bit in each 1 58 #10 10 500 HCKCB3BLG158S 1500 CB3BLG158S box; replacement bit model BIT3SU) Coarse threads Type-17 point C-3 mechanically-galvanized coating Straight collation
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
PRO LDH
PRO CGB
CB3BLGHL Screw
Common Application: Cement board to wood FEATURES:
Retail Pack Contractor Pack
Threads 0.375" ribbed wafer Length Shank PRO Per Fasteners Fasteners (in.) Size LDH head with nibs for Model No. Model No. Inch per Pack per Pack easy countersinking 15 #3 undersized square drive #9 High500 HCKCB3BLGHL114S 1500 CB3BLGHL114S 1 14 (Driver bit in each Low box; replacement bit 15 model BIT3SU) 1 58 #9 High500 HCKCB3BLGHL158S 1500 CB3BLGHL158S Low Alternating high-low threads Sharp point C-3 mechanically-galvanized coating Straight collation
PRO CGB
Black/Gray-Phosphate Coating 1 1 4 1 58 2 2 2 1 14 1 58 2 1 14 1 8
5 1 1
#6 #6 #6 #6 #8 #6 #6 #6 #6 #6
1000 1000
2500 2500 2500 2000 1500 2500 2500 2000 N2000 Coating 2500 2500
DWC1PS DWC114PS DWC158PS DWC2PS DWC212PS DWCZ114PS DWCZ158PS DWCZ2PS DWCG114PS DWCG158PS
Yellow-Zinc Coating
DWHL Screw
Common Application: Drywall to wood FEATURES:
Bugle head #2 Phillips drive (Driver bit in each box; replacement bit model BIT2P) High-low threads Sharp point Gray-phosphate coating Curved collation
Length (in.) 1 78 Shank Size #6 Carton Quantity 2000 Model No. PRO 250DW
DWHL178PS
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
DWF Screw
Common Application: Drywall to cold-formed steel (Recommended thicknesses: 33, 27 and 18 mils 20, 22 and 25 ga.) FEATURES:
Bugle head #2 Phillips (Driver bit in each box; replacement bit model BIT2P) Fine threads Sharp point Gray-phosphate coating Curved collation Codes/Standards: ASTM C1002-04 Type S compliant
Length (in.) 1 1 14 1 58 Shank Size #6 #6 #6 Carton Quantity 2500 2500 2500 Model No. PRO 200
See the General Load Table on page ___ for screw strength and shear-wall loads when used to install 12" gypsum drywall.
For information on corrosion, materials and coatings, see pages 10-13. These coated fasteners possess a level of corrosion resistance that makes them suitable for use in some exterior and corrosive environments and with some preservative-treated woods. For applications in higher-exposure applications, consider type-300 series stainless-steel fasteners for superior corrosion resistance. See pages 10-13 for additional important information before selecting a fastener for a specific application.
170
#6 #6 #6 #8
20 20 20 20
See the General Load Table on page 183 for screw strength and shear-wall loads when used to install 12" gypsum drywall.
WSCD/WSCT Screws
Common Application: Roofing tiles to wood FEATURES:
Flat head #3 square drive (Driver bit in each box; replacement bit model BIT3S) Twin threads Sharp point Curved collation WSCD with Class 55 mechanicallygalvanized coating is a Miami-Dade compliant roofing product per TAS114, Appendix E
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
Length (in.)
Shank Size
Carton Quantity
Model No.
PRO RF
PRO 300SRF
Available Coatings: Heavy zinc electroplate, mechanically galvanized class 55 coating Codes/Standards: ICC-ES ESR-2015P
SSWSCB Screw
Common Application: Roofing tiles to wood FEATURES:
Bugle head #2 square drive (Driver bit in each box; replacement bit model BIT2S) Coarse threads Type-17 point Type 305 stainless steel Curved collation A Miami-Dade compliant roofing product Codes/Standards: ICC-ES ESR-2015P
For information on corrosion, materials and coatings, see pages 10-13. These coated fasteners possess a level of corrosion resistance that makes them suitable for use in some exterior and corrosive environments and with some preservative-treated woods. For applications in higher-exposure applications, consider type-300 series stainless-steel fasteners for superior corrosion resistance. See pages 10-13 for additional important information before selecting a fastener for a specific application. Length (in.) 2 2 12 Shank Size #8 #8 Carton Quantity 2000 1500 Model No. PRO RF PRO 300SRF
SSWSC2BS SSWSC212BS
171
Model No.
Available Coatings/Material: Clear zinc, Quik Guard and type 410 stainless steel
PCSD Screw
Common Application: Standing-seam roofing panel clips to steel FEATURES:
Pancake head #2 square drive (Driver bit in each box; replacement bit model BIT2S) Drill point Straight collation Available Coatings/Material: Clear zinc, Quik Guard and type 410 stainless steel
Length (in.) Shank Size #2 Drive Type Threads Per Inch Carton Quantity PRO PP150
Model No.
Clear-Zinc Coating 1 1 1 1 1 #10 #12 #10 #12 #10 Standard Standard Undersized Undersized Standard 16 14
PCULP Screw
Common Application: Standing-seam-roofing (or snap and seam) panels to wood FEATURES:
Ultra low profile pancake head #2 square drive (Driver bit in each box; replacement bit model BIT2S) Type-17 point Straight collation Available Coatings/Material: Clear zinc, Quik Guard and type 410 stainless steel
Length (in.) Shank Size #2 Drive Type Threads Per Inch Carton Quantity Model No. PRO PP150
Clear-Zinc Coating 1 1 2 1 1 12 1
1
12 12 12 12 12
For information on corrosion, materials and coatings, see pages 10-13. These coated fasteners possess a level of corrosion resistance that makes them suitable for use in some exterior and corrosive environments and with some preservative-treated woods. For applications in higher-exposure applications, consider type-300 series stainless-steel fasteners for superior corrosion resistance. See pages 10-13 for additional important information before selecting a fastener for a specific application.
172
54 68 97 22 27 33 43 54 68 97
(22) (20) (18) (16) (14) (12) (22) (20) (18) (16) (14) (12) (24) (22) (20) (18) (16) (14) (12) Pancake Head Screw Metal Roofing-to-Steel PCSD1S1016 #10-16x1" 0.190 Allowable Load2 Average Ultimate Load Allowable Load2 Average Ultimate Load
4 4
168 250 385 570 570 570 172 255 430 420 570 875 1475 1645 1690 420 735 1220 156 295 420 585 585 585 210 320 505 400 695 955 1640 1890 2290 520 780 1245
67 68 95 138 255 310 171 166 235 340 630 760 66 66 88 129 255 320 170 162 240 315 625 785
PCSD1S1214
#12-14x1"
0.216
Pancake Head Screw Metal Roofing-to-Wood PC1BS1012 #10-12x1" 0.190 Allowable Load2 Average Ultimate Load Allowable Load2 Average Ultimate Load
4 4
170 255 475 475 765 1195 200 300 450 505 735 1100
PC1BS1211
#12-11x1"
0.216
Ultra Low Profile Pancake Head Screw Metal Roofing-to-Wood PCULP1BS1012 #10-12x1" 0.190 Allowable Load2 Average Ultimate Load
4
1. Screws and screw connections have been tested per AISI Standard Test Method S904-08 and S905-08. 2. The tabulated ASD allowable loads for cold-formed steel (CFS) members are based on the lower of the screw strength or the strength of the screw in the connected members per AISI S100-07 Section E4. 3. The safety factor is based on AISI S100-07 Chapter F for tested connections. 4. The average ultimate values listed are achieved under laboratory conditions and should not be used for design loads. 5. Values are based on CFS members with a minimum yield strength of Fy = 33 ksi and tensile strength of Fu = 45 ksi for 43 mil (18 ga) to 27 mil (22 ga), minimum yield strength of Fy = 50 ksi and tensile strength of Fu = 65 ksi for 22 mil (24 ga), and a minimum yield strength of Fy = 50 ksi and Fu = 65 ksi for 54 mil (16 ga) and thicker.
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
6. For design purposes,steel sheet thicknesses are 0.0227" for 22 mil, 0.283" for 27 mil, 0.0346" for 33 mil, 0.0451" for 43 mil, 0.0566" for 54 mil, 0.0713" for 68 mil, and 0.1017" for 97 mil. The actual sheet thickness shall not be less than 95% of these design thickness as specied in AISI A100-07 Section A2.4. 7. Screw diameters per AISI S200-07 General Provision Commentary Table D1.1. 8. Minimum required screw length is the lesser of 34" or the minimum length required for the screw to extend through the steel connection a minimum of 3 exposed threads per AISI S207-07 General Provisions Standard Section D1.3. 9. Larger of screw head or washer diameter, dw, for #10 and #12 screws is 0.375". 10. The allowable load (ASD) values shown are not permitted to be increased for short-duration loads such as wind or earthqueake loads. 11. The lower of the Pull-Over and Pull-Out allowable load should be used for tension design. 12. The tabulated shear values are based on the thinner steel member in connection. Steel thickness for both member must be in the range of 12-22 gauge.
Plywood 2 "
5
OSB
3
SYP
3
8 "
4 "
16 "
4 "
2x
Pancake Head Screw Metal Roofing to Wood PC1BS1012 #10-12x1" 0.190 Allowable Load1,2 Average Ultimate Load3 Allowable Load1,2 Average Ultimate Load
3
55 275 55 275
55 275 62 310
60 300 62 310
33 165 39 194
51 255 51 255
PC1BS1211
#12-11x1"
0.216
Ultra Low Profile Pancake Head Screw Metal Roofing to Wood PCULP1BS1012 #10-12x1" 0.190 Allowable Load1,2 Average Ultimate Load3 55 275 55 275 55 275 39 194 39 194 105 525
1. Values based on the lower screw strength or strength of the screw in the connected members. 2. The tabulated allowable loads for wood members are based on a factor of safety of 5 as specied in AC233 and may be multiplied by CD = 1.60 for wind or earthquake loads. 3. The average ultimate loads are achieved under laboratory conditions and should not be used for design purposes. 4. Screw diameters per AISI S200-07 General Provisons Commentary Table D1-1. 5. See page 183 for information on screw strength.
173
BGP 300
XJ Screw
Common Applications: Metal roofing/siding panels to wood or cold-formed steel (maximum thickness: 20 gauge) FEATURES:
16" hex head EPDM-backed washer Sharp point JS500 plating system Powder-coated head and washer Available in a variety of stock colors to match almost any roofing panel (see next page), custom colors available upon request
5
Length (in.) 1 1 4 1 2 2
1 1
BGP 300
SSH Screw
Common Applications: Metal roofing/siding panels to wood FEATURES:
1
1 2 2 212
HG Screw
Common Applications: Metal roofing/siding panels to wood or cold-formed steel (maximum thickness: 20 gauge) FEATURES:
14" hex head EPDM-backed washer Type-17 point for timber and light-steel battens Mechanically-galvanized coating compliant with ASTM B-695 Class 55 Not available in colors
Length (in.) 112 2 Shank Size #10 #10 Carton Quantity 500 500 Model No. HG112WT10 HG2WT10 BGP 300
The HJ, XJ and SSH screws are Master Gripper fasteners from Leland Industries. For technical and coating information on this screw series, visit www.lelandindustries.com/sst. Custom color matching is also available to match any project. For more information, contact SimpsonStrong-Tie. For information on corrosion, materials and coatings, see pages 10-13. 174 These coated fasteners possess a level of corrosion resistance that makes them suitable for use in some exterior and corrosive environments and with some preservative-treated woods. For applications in higher-exposure applications, consider type-300 series stainless-steel fasteners for superior corrosion resistance. See pages 10-13 for additional important information before selecting a fastener for a specific application.
4" hex head EPDM-backed washer Sharp point Type 304 stainless-steel fastener and washer JS600 plating system Available with powder-coated head and washer Available in a variety of stock colors to match almost any roofing panel (see next page), custom colors available upon request
Length (in.) 1
BGP 300
Black
QC262
0801
Bright Red
QC386
0703
Brown
QC326
1103
Stone
1001
Dark Gray
1006
Tile Red
0718
Buckskin
QC055
1108
Bone White
QC273
0103
Gray
1005
Red
QC259
0701
Saddle Tan
1107
MS White
0114
Charcoal
QC306
1007
Dark Green
0434
Tan
QC315
1106
White
QC317
0113
Ash Gray
QC305
1003
Medium Green
QC307
0402
Taupe
1117
Bright White
0105
Metallic Silver
QC2624
1404
In Canada, QC number codes reference the recognized color system of coil coater Baycoat Inc. in Hamilton, Ontario.
Length (in.)
Shank Size
Point Size
Carton Quantity
Model No.
PRO HX516
PRO PP150
X1S1016 X1S1214
Available Coatings: Clear zinc, Quik Guard Codes/Standards: ICC-ES ESR-3006 (asterisked sizes only) City of L.A. RR25670 ASTM C1513 compliant
16 14 24 24 24
3 3 4 5 5
8*
114* 112*
For roof-deck diaphragm loads see pages 185-191. * These sizes ICC-ES code-listed.
8 " 12 14 " 12
27 33 43 54 68 97 27 33 43 54 68 97 (22) (20) (18) (16) (14) (12) (22) (20) (18) (16) (14) (12) 240 710 760 960 960 960 69 145 145 245 290 605
16 "
4 "
2 " 12
360 1135 1215 1445 1445 1445 104 230 230 395 460 965 715 1745 1860 2400 2675 3030 205 365 355 605 705 1480 240 455 680 1000 1030 1350 78 135 145 220 245 545 360 725 1085 1595 1645 2020 117 215 235 355 395 870 715 1110 1665 2450 2520 4025 235 335 360 540 655 1405
Average Ultimate/ 390 655 930 1545 1540 1550 Nominal Load ASD Load 140 290 395 725 830 830 210 465 635 1155 1240 1240
XQ1S1214 X1S1214
#12-14 x 1"
0.216
LRFD Load
Average Ultimate/ 420 660 900 1640 2175 2200 Nominal Load ASD Load
XQ78S1224
140 230 350 640 740 935 935 935 240 290 400 720 790 1390 78
LRFD Load
210 365 560 1025 1175 1355 1355 1355 360 440 640 1155 1260 2160 117 125 185 320 415 735 1170 2135 2160
Average Ultimate/ 420 550 920 1455 1675 2675 2675 2675 715 875 985 1770 1930 3400 235 205 280 505 640 1130 1990 3370 4260 Nominal Load 0.0451" for 43 mil, 0.0566" for 54 mil, 0.0713" for 68 mil,and 0.1017" for 97 mil. The actual sheet thickness shall not be less than 95% of these design thickness as specied in AISI S100-7 Section A2.4. 7. Screw diameters per AISI S207-07 General Provisions Commentary Table D1-1. 8. Minimum required screw length is the lesser of 34" or the minimum length required for the screw to extend through the steel connection a minimum of 3 exposed threads per 2004 AISI General Provisions Standard section D1.3. 9. Screw head or washer diameter, dw for #10 and #12 screws is 0.398". 10. The allowable load (ASD) values showing are not permitted to be increased for short-duration loads such as wind or earthquake loads. 11. The lower of the pull-over and pull-out allowable load should be used for tension design. 12. Not applicable for XQ78S1224. 13. The tabulated shear values are based on the thinner steel member in connection. Steel thickness for both member must be in the range of 12" - 22 gauge. 14. See page 183 for information on screw strength.
1. Screws and screw connections have been tested per AISI Standard Test Method S904-08 and S905-08 with the exception of 22 gauge values which are based on calculations of the AISI S100-07 Section E4. 2. The tabulated ASD and LRFD allowable loads for cold-formed steel (CFS) members are based on the lower of the screw strength or the strength of the screw in the connected members per AISI S100-07. 3. The safety factor and resistance factor used to determine the ASD and LRFD strength are based on AISA S100-2007 Section F. 4. The average ultimate values listed are achieved under laboratory conditions and should not be used for design loads. 5. Values are based on CFS members with a minimum yield strength of Fy = 33 ksi and tensile strength of Fu = 45 ksi for 43 mil (18 ga) to 27 mil (22 ga), minimum yield strength of Fy = 50 ksi and Fu = 65 ksi for 54 mil (16 ga) to 97 mil (12 ga), and a minimum yield strength of Fy = 36 ksi and Fu = 58 ksi for 18" and thicker. 6. For design purposes,steel sheet thicknesses are 0.0283" for 27 mil, 0.0346" for 33 mil,
For information on corrosion, materials and coatings, see pages 10-13. These coated fasteners possess a level of corrosion resistance that makes them suitable for use in some exterior and corrosive environments and with some preservative-treated woods. For applications in higher-exposure applications, consider type-300 series stainless-steel fasteners for superior corrosion resistance. See pages 10-13 for additional important information before selecting a fastener for a specific application.
176
Length (in.)
3
Point Size 2
Model No.
PRO PH
TRSD34S1016
566 1070
1. Screws and screw connections (Shear 12-20 gauge, Pull-out 14-20 gauge) have been tested per AISI Standard Test Method S904-08 and S905-08. Other loads are based on calculations with Section E4 of the AISI S100-07. 2. The tabulated ASD and LRFD allowable loads for cold-formed steel (CFS) members are based on the lower of the screw strength or the strength of the screw in the connected members per AISI S100-2007 Section E4. 3. The safety factor is based on AISI S100-07 Chapter F for tested connections. 4. The average ultimate/nominal values should not be used for design loads. 5. Values are based on CFS members with a minimum yield strength of Fy = 33 ksi and tensile strength of Fu = 45 ksi for 43 mil (18 ga) to 27 mil (22 ga), minimum yield strength of Fy = 50 ksi and Fu = 65 ksi for 54 mil (16 ga) to 97 mil (12 ga), and a minimum yield strength of Fy = 36 ksi and Fu = 58 ksi for 18" and thicker. 6. For design purposes,steel sheet thicknesses are 0.0283" for 27 mil, 0.0346" for 33 mil, 0.0451" for 43 mil, 0.0566" for 54 mil, 0.0713" for 68 mil, and 0.1017" for
97 mil. The actual sheet thickness shall not be less than 95% of these design thickness as specied in AISI S100-07 Section A2.4. 7. Screw diameters per AISI S200-07 General Provision Commentary Table D1.1. 8. Minimum required screw length is the lesser of 34" or the minimum length required for the screw to extend through the steel connection a minimum of 3 exposed threads per AISI S207-07 General Provisions Standard Section D1.3. 9. Screw head or washer diameter, dw is 0.357". 10. The allowable load (ASD) values showing are not permitted to be increased for short-duration loads such as wind or earthquake loads. 11. The lower of the pull-over and pull-out allowable load should be used for tension design. 12. The tabulated shear values are based on the thinner steel member in connection. Steel thickness for both member must be in the range of 12-22 gauge. 13. See general load tables on page 183 for screw strength.
For information on corrosion, materials and coatings, see pages 10-13. 177
Length (in.)
3
Shank Size #8
Point Size 2
Model No.
PRO PH
PHSD34S0818
Pull-Over (lbs) Steel Thickness: mil (ga) 97 (12) 420 27 33 (22) (20) 195 239 43 (18) 310 54 (16) 565 68 (14) 605
6
Pull-Out (lbs) Steel Thickness: mil (ga)6 97 (12) 605 27 33 (22) (20) 59 125 43 (18) 133 54 (16) 214 68 (14) 245 97 (12) 305
PHSD34S0818
#8-18 x 34"
0.164
182
375
490
675
675
675
295
360
465
845
905
905
89
200
213
340
395
460
365
590
765
960
960
960
585
715
178
310
325
525
605
920
For information on corrosion, materials and coatings, see pages 10-13. 178
1. Screws and screw connections(Shear 12-20 gauge, Pull-out 14-20 gauge) have been tested per AISI Standard Test Method S904-08 and S905-08. Other values are based on calculations with Section E4 of the AISI S100-07. 2. The tabulated ASD and LRFD allowable loads for cold-formed steel (CFS) members are based on the lower of the screw strength or the strength of the screw in the connected members per AISI S100-2007 Section E4. 3. The safety factor is based on AISI S100-07 Chapter F for tested connections. 4. The average ultimate/nominal values listed should not be used for design loads. 5. Values are based on CFS members with a minimum yield strength of Fy = 33 ksi and tensile strength of Fu = 45 ksi for 43 mil (18 ga) to 27 mil (22 ga), minimum yield strength of Fy = 50 ksi and Fu = 65 ksi for 54 mil (16 ga) to 97 mil (12 ga). 6. For design purposes,steel sheet thicknesses are 0.0283" for 27 mil, 0.0346" for 33 mil, 0.0451" for 43 mil, 0.0566" for 54 mil, 0.0713" for 68 mil, and 0.1017" for
97 mil. The actual sheet thickness shall not be less than 95% of these design thickness as specied in AISI S100-07 Section A2.4. 7. Screw diameters per AISI S200-07 General Provision Commentary Table D1.1. 8. Minimum required screw length is the lesser of 34" or the minimum length required for the screw to extend through the steel connection a minimum of 3 exposed threads per AISI S207-07 General Provisions Standard Section D1.3. 9. Screw head or washer diameter, dw is 0.307". 10. The allowable load (ASD) values showing are not permitted to be increased for short-duration loads such as wind or earthquake loads. 11. The lower of the pull-over and pull-out allowable load should be used for tension design. 12. The tabulated shear values are based on the thinner steel member in connection. Steel thickness for both member must be in the range of 12-22 gauge. 13. See general load tables on page 183 for screw strength.
Point Size 3 3
Model No.
PRO PP150
PRO PH
4 4
FPHSD34S1016 FPHSD34S1214
For shear load values with steel sheet see page 184.
835 1085 1970 2215 2215 360 545 655 825 1125
850 1215
1. The tabulated values are based on calculations with Section E4 of the AISI S100-07. 2. The tabulated ASD and LRFD allowable loads for cold-formed steel (CFS) members are based on the lower of the screw strength or the strength of the screw in the connected members per AISI S100-07 Section E4. 3. Values are based on CFS members with a minimum yield strength of Fy = 33 ksi and tensile strength of Fu = 45 ksi for 43 mil (18 ga) to 27 mil (22 ga), minimum yield strength of Fy = 50 ksi and Fu = 65 ksi for 54 mil (16 ga) to 97 mil (12 ga). 4. For design purposes,steel sheet thicknesses are 0.0283" for 27 mil, 0.0346" for 33 mil, 0.0451" for 43 mil, 0.0566" for 54 mil, 0.0713" for 68 mil, and 0.1017" for 97 mil. The actual sheet thickness shall not be less than 95% of these design thickness as specied in AISI S100-07 Section A2.4.
5. Screw diameters per AISI S200-07 General Provision Commentary Table D1.1. 6. Minimum required screw length is the lesser of 34" or the minimum length required for the screw to extend through the steel connection a minimum of 3 exposed threads per AISI S207-07 General Provisions Standard Section D1.3. 7. Screw head or washer diameter, dw for #10 and #12 screws is 0.357". 8. The allowable load (ASD) values showing are not permitted to be increased for short-duration loads such as wind or earthquake loads. 9. The lower of the pull-over and pull-out allowable load should be used for tension design. 10. The tabulated shear values are based on the thinner steel member in connection. Steel thickness for both member must be in the range of 12-22 gauge. 11. See the general load tables on page 183 for screw strength.
For information on corrosion, materials and coatings, see pages 10-13. 179
WSF1LRVS WSF134LRVS
FHSD Screw
Common Application: Wood to cold-formed steel (Recommended thicknesses: 316") FEATURES:
Flat head #2 square drive (Driver bit in each box; replacement bit model BIT2S) except FHSD212S1214 which is a #3 square drive (replacement bit model BIT3S) #2 drill point Curved collation Type 410 stainless-steel screw has nibs under the head for easy countersinking 212" length has wings on the shaft to prevent jacking of the wood panel during installation
112 #10 18 2 Length (in.) Shank Size
Point Size
Carton Quantity
Model No.
PRO 200S
PRO 200
PRO HSD60
#8 #12
18 14
2 4
2500 750
FHSD114S0818 FHSD212S1214
1"-112" lengths
Available Coatings/Materials: Clear zinc, yellow zinc, type 410 stainless steel Codes/Standards: ASTM C1513 compliant 212" length
For information on corrosion, materials and coatings, see pages 10-13. 180
Model No.
Yellow-Zinc Coating #14 #14 #14 14 14 14 Standard Standard Standard 1000 750 750 TB1445S TB1460S TB1475S
Black-Phosphate Coating #12 #12 #14 #14 14 14 14 14 Standard Standard Standard Standard
N2000 Coating #12 #12 #14 #14 #14 14 14 14 14 14 Undersized Undersized Undersized Undersized Undersized 1000 1000 1000 750 750 TBG1245S TBG1260S TBG1445S TBG1460S TBG1475S
Allowable Loads for Wood Attachment to Steel with Quik Drive TB Screws (Steel Members 16 ga - 516" Thick)
DF/SP Allowable Load
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
Model No.
L (mm)
Wood Size
Uplift (160) 195 225 390 195 225 390 210 210 215 210 210 215
TB1460S
2 38" (60) 2x
14 ga 12 ga - 516" 16 ga 14 ga 12 ga - 516"
TB1475S
3" (75)
1. For use with structural steel members up to 516" thick or cold-formed steel members 16 gauge (54 mil) or thicker. 2. Standard product available in a black phosphate, yellow zinc or N2000 coating for additional corrosion protection (TBG1460S or TBG1475S). 3. For use with 2x (112") DF/SP only. 4. For use with QD HSD60 or HSD75 Tool. 5. (160) loads shall only be used when resisting wind or seismic loads.
ift Upl
1" Min .
Shear
Shear
1" Min.
in. 4" M
in. 3" M
ax. " M
4" Min.
WARNING: Industry studies show that hardened fasteners can experience performance problems in wet or corrosive environments. Accordingly, use this product in dry, interior, and noncorrosive environments only.
1" Min.
For information on corrosion, materials and coatings, see pages 10-13. These coated fasteners possess a level of corrosion resistance that makes them suitable for use in some exterior and corrosive environments and with some preservative-treated woods. For applications in higher-exposure applications, consider type-300 series stainless-steel fasteners for superior corrosion resistance. See pages 10-13 for additional important information before selecting a fastener for a specific application. 181
Point Size 2 2
Model No.
PRO 200S
PRO 250
PRO 300S
CBSDQ158S CBSDQ214S
SSX Screws
Common Applications: Aluminum and fiberglass FEATURES:
516" hex head #3 drill point (not suitable for drilling steel) Belt collation Available Materials: Types 305 and 316 stainless steel
Length (in.) Shank Size Threads Per Inch
Point Size
Carton Quantity
Model No.
BGP 300
14 14 14 14 14
3 3 3 3 3
Type 316 Stainless Steel 1 112 2 212 3 #12 #12 #12 #12 #12 14 14 14 14 14 3 3 3 3 3 500 500 500 500 500 SSX1T1214-316 SSX112T1214-316 SSX2T1214-316 SSX212T1214-316 SSX3T1214-316
For information on corrosion, materials and coatings, see pages 10-13. These coated fasteners possess a level of corrosion resistance that makes them suitable for use in some exterior and corrosive environments and with some preservative-treated woods. For applications in higher-exposure applications, consider type-300 series stainless-steel fasteners for superior corrosion resistance. See pages 10-13 for additional important information before selecting a fastener for a specific application. 182
Pss
895 1320 750 945 920 1240
Pts
1110 1690 905 1060 1145 2020
Metal-Roofing Clip to Steel PCSD1S1016 PCSD1S1214 SSPCSD1S1016 #10 x 1" #12 x 1" #10 x 1" 1705 1760 1892 2380 3180 3045 850 880 985 1190 1590 1588 570 585 631 795 1060 1015
1575 1575 1575 1720 1720 1720 1720 1720 Wood to Steel
1. Table based on testing per AISI Standard Test Method S904-08. 2. Factor of Safety (), and Resistance Factor () are determined per AISI S100-07 Section F1. 3. Pss and Pts are nominal shear strength and nominal tension strength values for the screw itself, respectively, and are also known as the average (ultimate) values of all tests determined by independent laboratory testing.
183
Assembly Description
2" gypsum board on one side of wall; steel studs max. 24" o.c.
2:1
1. Nominal strength shall be multiplied by the resistance factor ( = 0.6 LRFD Seismic, = 0.65 LRFD Wind) to determine design strength or divided by the safety factor ( = 2.5 ASD Seismic, = 2.0 ASD Wind) to determine allowable strength. 2. For gypsum sheathed shear walls, tabulated values shall be applicable for short-term load duration only (wind or seismic loads). 3. Gypsum board shall comply with ASTM C1396. 4. Gypsum Board shall be applied horizontal with 33 mil strap blocking of 1 12" width, In addition, solid blocking is required between the rst two end studs. Alternatively, sheets may be applied vertically or values can be multiplied by 0.35. 5. Studs and track shall be a minimum thickness of 33 mils. 6. Table based on Table C2.1-2 AISI Standard North American Standard for Cold-Form Steel Framing-Lateral Design 2007 Edition with Supplement No. 1 and Commentary.
Quik Drive TRSD, PHSD and FPHSD (#10) Screws: Nominal Shear Strength (Rn) for Wind and Seismic for Shear Walls1 (lbs/ft)
Max. Aspect Ratio (h/w) 4:1 0.027" Steel Sheet, one side 2:13 647 710 778 845 33 (min.)
1. Nominal strength shall be multiplied by the resistance factor ( = 0.6, LRFD Seismic, = 0.65, LRFD Wind) to determine design strength or divided by the safety factor ( = 2.5, ASD Seismic, = 2.0, ASD Wind) to determine allowable strength. 2. Screws in the eld of the panel shall be installed 12" (305 mm) on center (o.c.). 3. Shear wall height to width aspect ratio (h/w) greater than 2:1, but not exceeding 4:1, shall be permitted provided the nominal strength values are multiplied by 2w/h. 4. Wall studs and track shall be of ASTM A1003 Stuctural Grade 33 (Grade 230) Type H steel for members with a designation thickness of 33 and 43 mils. 5. In lieu of blocking, panel edges shall be permitted to be overlapped and attached to each other with screw spacing as required for panel edges. Where such a connection is used, tabulated design values shall be reduced 30%. 6. Maximum stud spacing 24" o.c. 7. Blocking, if applicable, shall be a minimum 33 mil 1 12" width. 8. Table based on Table C2.1-3 AISI Standard North American Standard for Cold-Form Steel Framing-Lateral Design 2007 Edition with Supplement No. 1 and Commentary.
Assembly Description
184
Evaluation Parameters
All nominal shear strength values are for a three-span condition. Higher values would be obtained for a 1- or 2-span condition since there are more fasteners to count in the calculation of strength. The fastener layout pattern is the same at both end-members and interior supports. The number of side-lap stitch connectors is assumed to be the same as the number of extreme-edge fasteners. Nominal diaphragm shears due to panel buckling are tabulated at the bottom of the pages to check whether the panel buckling governs over connector strength for diaphragm design. The tables were done in this manner to address the different safety or resistance factors that apply to connector strength and panel buckling. For roof deck, the steel yield point is taken at 33 ksi. For specic design application not listed, the Designer is required to make direct use of the strength and stiffness formulas in the Steel Deck Institutes Diaphragm Design Manual, Third Edition. The column K1 , in the Nominal Shear Strength table, gives the slip relaxation coefcient of the assembly. The column I, in the Nominal Shear Due to Panel Buckling table, gives the panel moment of inertia per unit panel width.
Limiting Conditions
End Laps
At interior positions, panels must be sufciently overlapped to provide adequate end distances for the connector used. A minimum end distance for fasteners used should be 1" requiring an end lap not less than 2". Within the system, end laps may be staggered or on a continuous line without particular effect on the diaphragm strength. However, greater care must be exercised in the making connections through multiple layers of deck at the panel corners on the end lap. If panels are butted at their ends rather than end lapped, as is common with oor decks, then each panel must be individually connected at its end with the specied pattern.
Side Laps
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
The overlapping edges of panels should be in close contact to allow minimum eccentricity of fasteners in the lap. When stitch fasteners connect adjacent panels between supports, equivalent or superior fasteners should be used on the panels at the outermost edge of the diaphragm perimeter. Otherwise shear strength along the rst interior side-lap may exceed that along the perimeter member and thus diminish the contribution of the stitch fasteners.
Screws
Screws must be installed using properly calibrated tools to avoid overdriving which can strip the threads at side-laps or sever the screw when it is placed into heavier substrata.
1.5 (WR, IR, NR) 36" Coverage 36/9 Pattern 36/7 Pattern 36/5 Pattern 36/4 Pattern Typical Fastener Layout
185
36/9
36/7
36/5
36/4
Nominal shear listed shall be used with the appropriate or factor and may also be limited by panel shear buckling (reference table below). (Buckling) = 0.80, (Buckling) = 2.00
Deck Profile NR IR WR I (in4/ft.) 0.099 0.108 0.152 Nominal Shear Due to Panel Buckling (Sn), (plf/span, ft.) 4 2324 2481 3205 4.5 1836 1960 2533 5 1487 1588 2051 5.5 1229 1312 1695 6 1033 1102 1425 6.5 880 939 1214 7 759 810 1047 7.5 661 706 912 8 581 620 801
186
1. ASD Required Strength (Service Applied Load) Minimum [Nominal Shear Strength / (Seismic or Wind), Nominal Buckling Strength Sn / (Buckling)] 2. LRFD Required Strength (Factored Applied Load) Minimum [ (EQ or WIND) x Nominal Shear Strength, (Buckling) x Nominal Buckling Strength Sn]
36/9
36/7
36/5
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
36/4
Nominal shear listed shall be used with the appropriate or factor and may also be limited by panel shear buckling (reference table below). (Buckling) = 0.80, (Buckling) = 2.00
Deck Profile NR IR WR I (in4/ft.) 0.128 0.139 0.198 Nominal Shear Due to Panel Buckling (Sn), (plf/span, ft.) 4 3258 3466 4519 4.5 2574 2738 3570 5 2085 2218 2892 5.5 1723 1833 2390 6 1448 1540 2008 6.5 1234 1312 1711 7 1064 1132 1476 7.5 927 986 1285 8 814 866 1130
1. ASD Required Strength (Service Applied Load) Minimum [Nominal Shear Strength / (Seismic or Wind), Nominal Buckling Strength Sn / (Buckling)] 2. LRFD Required Strength (Factored Applied Load) Minimum [ (EQ or WIND) x Nominal Shear Strength, (Buckling) x Nominal Buckling Strength Sn]
187
36/9
36/7
36/5
36/4
Nominal shear listed shall be used with the appropriate or factor and may also be limited by panel shear buckling (reference table below). (Buckling) = 0.80, (Buckling) = 2.00
Deck Profile NR IR WR I (in4/ft.) 0.181 0.196 0.284 Nominal Shear Due to Panel Buckling (Sn), (plf/span, ft.) 4 5215 5535 7310 4.5 4120 4374 5576 5 3337 3543 4679 5.5 2758 2928 3867 6 2318 2460 3249 6.5 1975 2096 2768 7 1703 1807 2387 7.5 1483 1575 2079 8 1304 1384 1828
188
1. ASD Required Strength (Service Applied Load) Minimum [Nominal Shear Strength / (Seismic or Wind), Nominal Buckling Strength Sn / (Buckling)] 2. LRFD Required Strength (Factored Applied Load) Minimum [ (EQ or WIND) x Nominal Shear Strength, (Buckling) x Nominal Buckling Strength Sn]
36/9
36/7
36/5
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
36/4
Nominal shear listed shall be used with the appropriate or factor and may also be limited by panel shear buckling (reference table below). (Buckling) = 0.80, (Buckling) = 2.00
Deck Profile NR IR WR I (in4/ft.) 0.099 0.108 0.152 Nominal Shear Due to Panel Buckling (Sn), (plf/span, ft.) 4 2324 2481 3205 4.5 1836 1960 2533 5 1487 1588 2051 5.5 1229 1312 1695 6 1033 1102 1425 6.5 880 939 1214 7 759 810 1047 7.5 661 706 912 8 581 620 801
1. ASD Required Strength (Service Applied Load) Minimum [Nominal Shear Strength / (Seismic or Wind), Nominal Buckling Strength Sn / (Buckling)] 2. LRFD Required Strength (Factored Applied Load) Minimum [ (EQ or WIND) x Nominal Shear Strength, (Buckling) x Nominal Buckling Strength Sn]
189
36/9
36/7
36/5
36/4
Nominal shear listed shall be used with the appropriate or factor and may also be limited by panel shear buckling (reference table below). (Buckling) = 0.80, (Buckling) = 2.00
Deck Profile NR IR WR I (in4/ft.) 0.128 0.139 0.198 Nominal Shear Due to Panel Buckling (Sn), (plf/span, ft.) 4 3258 3466 4519 4.5 2574 2738 3570 5 2085 2218 2892 5.5 1723 1833 2390 6 1448 1540 2008 6.5 1234 1312 1711 7 1064 1132 1476 7.5 927 986 1285 8 814 866 1130
190
1. ASD Required Strength (Service Applied Load) Minimum [Nominal Shear Strength / (Seismic or Wind), Nominal Buckling Strength Sn / (Buckling)] 2. LRFD Required Strength (Factored Applied Load) Minimum [ (EQ or WIND) x Nominal Shear Strength, (Buckling) x Nominal Buckling Strength Sn]
36/9
36/7
36/5
C-FS11 2011 SIMPSON STRONG-TIE COMPANY INC.
36/4
Nominal shear listed shall be used with the appropriate or factor and may also be limited by panel shear buckling (reference table below). (Buckling) = 0.80, (Buckling) = 2.00
Deck Profile NR IR WR I (in4/ft.) 0.181 0.196 0.284 Nominal Shear Due to Panel Buckling (Sn), (plf/span, ft.) 4 5215 5535 7310 4.5 4120 4374 5776 5 3337 3543 4679 5.5 2758 2928 3867 6 2318 2460 3249 6.5 1975 2096 2768 7 1703 1807 2387 7.5 1483 1575 2079 8 1304 1384 1828
1. ASD Required Strength (Service Applied Load) Minimum [Nominal Shear Strength / (Seismic or Wind), Nominal Buckling Strength Sn / (Buckling)] 2. LRFD Required Strength (Factored Applied Load) Minimum [ (EQ or WIND) x Nominal Shear Strength, (Buckling) x Nominal Buckling Strength Sn]
191
NOTES
192
NOTES
193
NOTES
194
NOTES
195
The Fastener Finder provides both hand-drive and collated options, including fasteners for our Quik Drive auto-feed screw driving systems.
Novices and pros alike can easily search based on what they know about the fastener they are looking for. Results show all model numbers and available packaging sizes to make ordering easy.
Home Office 5956 W. Las Positas Blvd. Pleasanton, CA 94588 Tel: 925/560-9000 Fax: 925/847-1603 Northwest USA 5151 S. Airport Way Stockton, CA 95206 Tel: 209/234-7775 Fax: 209/234-3868 Southwest USA 12246 Holly Street Riverside, CA 92509 Tel: 714/871-8373 Fax: 951/369-2889
Northeast USA 2600 International St. Columbus, OH 43228 Tel: 614/876-8060 Fax: 614/876-0636 Southeast USA 2221 Country Lane McKinney, TX 75069 Tel: 972/542-0326 Fax: 972/542-5379 Quik Drive Factory 375 N. Belvedere Drive Gallatin, TN 37066 Tel: 888/487-7845 Fax: 615/451-9806
Eastern Canada 5 Kenview Boulevard Brampton, ON L6T 5G5 Tel: 905/458-5538 Fax: 905/458-7274 Western Canada 11476 Kingston Street Maple Ridge, B.C. V2X 0Y5 Tel: 604/465-0296 Fax: 604/465-0297 Simpson Strong-Tie Anchor Systems 136 Official Road Addison, IL 60101 Tel: 630/543-2797 Fax: 630/543-7014
Specials Factories Kent, WA Eagan, MN Distribution Centers Enfield, CT High Point, NC Jacksonville, FL Jessup, MD Langley, B.C. Ontario, CA International Facilities Please visit our website for contact details.
Printed in U.S.A.