Professional Documents
Culture Documents
Instructions
You will need a craft knife or other sharp knife, a pair of scissors, some glue and a glue spreader. The best type of glue to use is white school glue (PVA.) Print out the parts sheets onto thin cardboard. Photocopier card is ideal. Notice that the parts pages are marked front and back. Print out a front page, flip it over, then print the back onto the same sheet. Leave the ink to dry completely before continuing. Before cutting anything out, score along all the dotted lines and cut out any holes with a craft knife. Both these jobs are easier to do on full sheets of card. Dashed lines are hill folds, dotted lines are valley folds. Cut along the solid lines. Grey areas show where to glue Youll need four coins about this size Dashed lines are hill folds Dotted lines are valley folds
Cut out
1
Glue the flaps 1&2 down.
2
Fold round and glue the two coin holders to make little packets. These provide weight to help the goat move more positively. Glue Glue together the two push buttons (14-25) as shown. Glue a coin holder into each push button.
Fold over the two flaps (1&2) so that they are at ninety degree as show above and glue them into place. Glue together the box as shown in the picture. Assemble and glue on the box stiffener. (3-13)
Assemble the lower push rods and glue them into place on the push buttons. (26-29) Be careful with the next bit!
or-goat Instructions 1
or
-g
t oa
an
d-g
t oa
Before you glue the push buttons into place make sure that you thread the two push rods up through the hole in the top of the box. Now glue the push buttons into place (30-31). Make sure that they move freely.
5
Assemble the neck (32) and the two lift links. (33-34) Glue the lift links to the neck as shown here. (35-36)
6
Lift link Neck Assemble the pivot and glue on the hinge. (37-38)
Pivot
Assemble the two link bars (40-41) and glue them into place. (42-43) Assemble the two upper pushrods (44-45) and glue them into place. (46-47) Assemble the two-coin coin holder as shown in the and-goat instructions. Glue it into place on the neck. (48)
Glue the the alignment piece into place on the inside of the body as shown in the and-goat instructions. (49) Glue the pivot assembly to the alignment piece. (50) (Not shown in the picture)
Assemble the body inners (52-53) Glue the body inners into place carefully lining up the curved edges. (54-55) Glue the body back into place (57) Assemble the four legs and glue them into place. Make sure you match the the orange and green circles. (58-59)
or-goat Instructions 2
Assemble the head and horns glue them into place on the neck. (60-65) Glue on the eyes, ears and assembled tail. Glue the left side feet to the box top (66) Carefully - this is tricky! - join the two halves of the two pushrods. Glue the last two flaps of the body back. (67) Finally glue the right side feet to the box top (68)
or-goat
0 0
1 1
or-goat Instructions 3
Coin holder
9 66. 66. 68 68
66.
68
13
8 5 Cut out 6
or-goat
or-goat
Box
or-goat
Coin holder
12
11
9 2 8 31 11 30
10 4 7 1 5
59
59
53
59
Body Inner
Back
23
Push Button
21 2 coins
48 15
Push Button
Coin holder
18
31
16
29
54 59 24
52
22
17
55
28
30
25
75
75
53
52
kcaB
75
32
22
25
03
82
20
21
snioc 2
coin
14
61
16
81
19
55 20
71
12
22
51
15
42
45
35
75 23 coin
kcaB
25 24 14 92
84 17 19
13 18
Hinge 33 39 38
Horns
Head 63
Horns
Lift Link 35
43
63
62
62
Eyes
Ears
34
61
42
60
Neck
32 Link Bar
61
60
64
35 36 46 38 41
40 50 47
42
39
33
64 65 62 32 48
34
41
48
60
60
63
40
37
65
62
63
61
39
61
Body back 57 Lower push rod Lower push rod Upper push rod Upper push rod 44 45 59 59 Legs 59 59 Legs Tail
Front
Body
67
58 58
67
Alignment piece
27
26
50
58 58
29
28
26
45
56
56
56
56
55
Front
49
54
47
44
27
49
68
66
66
68
46 68 66
67
57
68 66
67