Professional Documents
Culture Documents
System Requirements
System Requirements
Ethernet-based Cable or DSL Modem Computers with Windows, Macintosh, or Linux-based operating systems with an installed Ethernet adapter Internet Explorer 6.x and above, or Netscape Navigator 7.0 and above
Package Contents
D-Link DIR-100
Power Adapter
If any of the above items are missing, please contact your reseller.
Hardware Overview
Hardware Overview
Power LED A solid light indicates a proper connection to the power supply.
Status LED A blinking light indicates that the DIR-100 is functioning properly.
Local Network LEDs A solid light on each port indicates a connection to an Ethernet enabled device. These LEDs blink during data transmission.
WAN LED A solid light indicates a connection on the WAN port. This LED blinks during data transmission.
Hardware Overview
LAN Ports These are the connections for Ethernet cables to Ethernet-enabled computers.
WAN Port This is for the connection of an Ethernet cable to your Cable or DSL modem.
Reset Button Pressing this button restores the Router to its original factory default settings.
Power Receptor
Hardware Installation
Hardware Installation
A. First, connect the power adapter to the receptor at the back panel of the DIR-100 and then plug the other end of the power adapter to a wall outlet or power strip. The Power LED will turn ON to indicate proper operation. B. 1. Power off your Cable or DSL modem; some devices may not have a on/off switch and will require you to unplug the power adapter. Now, the DIR-100 should be powered on and the Cable/ DSL modem should be turned off. . Cable/DSL modem (Power Off) DIR-100 (Power On) Connect an Ethernet cable to the Ethernet jack located on the Cable/DSL modem. After the Ethernet cable is securely connected, power on the Cable/DSL modem by turning on the unit or plugging in the power adapter. . Cable/DSL modem (Power On) DIR-100 (Power On) Insert the other end of the Ethernet cable to the WAN PORT on the back panel of the DIR-100. The WAN LED light will illuminate to indicate proper connection. If the WAN LED is not illuminated, please go back to step B1 and repeat the instructions. C. Insert an Ethernet cable to LAN port 1 on the back panel of the DIR-100 and an available Ethernet port on the network adapter in the computer you will use to configure the DIR-100. The LED light for LAN Port 1 will illuminate to indicate proper connection. Note: The LAN Ports on the DIR-100 are Auto-MDI/MDIX. Meaning you can use a straight-through or crossover Ethernet cable to the LAN Ports. D. Computers equipped with Ethernet or Gigabit Ethernet adapters will be able to connect to the DIR-100. The DFE-50TX or DGE50T PCI Adapters (as examples) will be able to connect with the router without any additional configuration required.
Getting Started
Getting Started
Configuration
Configuration
This section will show you how to configure your new D-Link DIR-100 Router using the D-Link Setup Wizard.
Open your Web browser and type http://192.168.0.1 into the URL address box. Then press the Enter or Return key.
Type admin for the username and leave the password field blank.
Click Log In
Configuration
Click Next
You have the option to establish a password for the User Name Admin.
Click Next
Click Next
Configuration
Dynamic IP Address
You will be prompted to select the type of Internet connection for your router. If you are unsure of which setting to select, please contact your Internet Service Provider. PPPoE - page 10 PPTP - page 11 LTP - page 1 Big Pond - page 1 Static IP Address - page 1
Click Next
If you selected Dynamic IP Address, this screen will appear: (Used mainly for Cable Internet service).
Click the Clone MAC Address button to automatically copy the MAC address of the network adapter in your computer. You can also manually type in the MAC address.
Click Next
Continue to page 15
Configuration
PPPoE
If your ISP uses PPPoE (Point-to-Point Protocol over Ethernet), select the corresponding radio button.
Click Next
If you have a Dynamic IP connection, enter the User Name and Password provided to you by your ISP.
Click Next
Note: Please be sure to remove any existing PPPoE client software installed on your computers.
Continue to page 15
10
Configuration
PPTP
If your ISP uses PPTP (Point to Point Tunneling Protocol), select the corresponding radio button.
Click Next
If you have a Dynamic IP connection, enter the Server IP, PPTP Account, and Password provided to you by your ISP.
Click Next
If you have a Static IP connection, enter the IP Address, Subne t Mask, Gateway IP Address, Server I P, P P T P A c c o u n t , a n d Password provided to you by your ISP.
Click Next
Continue to page 15
11
Configuration
L2TP
If your ISP uses LTP (Layer Two Tunneling Protocol), select the corresponding radio button.
Click Next
If you have a Dynamic IP connection, enter the LTP Server IP Address, User Name, and Password provided to you by your ISP.
Click Next
I f yo u h ave a S t a t i c I P connection, enter the LTP IP Address, Subnet Mask, Gateway IP Address, LTP Server IP, User Name, and Password provided to you by your ISP.
Click Next
Continue to page 15
1
Configuration
Big Pond
Select this option if you connect to the internet through Telstra BigPond Cable Broadband in Australia.
Click Next
Enter the User Name, and Password provided to you by your ISP.
Click Next
Continue to page 15
1
Configuration
Static IP Address
If your ISP requires a Static IP Address, please select the corresponding radio button.
Click Next
Enter the IP address that was originally provided to you by your ISP. You will need to complete all of the required fields.
Click Next
Continue to page 15
1
Configuration
Click Restart
15
Appendix
Appendix
To connect to the network, make sure the network adapter in your computer is configured properly. Heres how to configure the network adapter to obtain an IP address automatically when using the DIR-100 Router. For Microsoft Windows XP: Right click on My Network Places and select Properties. Right click on the Network Connection associated with the Ethernet adapter and select Properties (i.e., D-Link DFE-50TX+).
Click Internet Protocol (TCP/IP) and then click Properties. Click OK
Click OK
16
Appendix For Apple Macintosh OS X: Go to the Apple Menu and click on System Preferences, and select Network.
Click Network
The IP address information, the Subnet Mask, the Routers IP address, and the Ethernet adapter address will appear.
17
You can find software updates and user documentation on the D-Link website.
Technical Support
Technical Support
You can find software updates and user documentation on the D-Link website.
Tech Support for customers within South Eastern Asia and Korea:
D-Link South Eastern Asia and Korea Technical Support over the Telephone: +65-65-555 Monday to Friday :00am to 1:0pm, :00pm-6:00pm Singapore Time D-Link Technical Support over the Internet: email:support@dlink.com.sg
You can find software updates and user documentation on the D-Link website.
Technical Support
You can find software updates and user documentation on the D-Link website. D-Link provides free technical support for customers for the duration of the warranty period on this product. Customers can contact D-Link technical support through our web site or by phone.
Technical Support
You can find software updates and user documentation on the D-Link website.
Technical Support
Tech Support for customers within the U.A.E & North Africa:
D-Link Technical Support over the Telephone: (71) -1-60 (U.A.E) Sunday to Wednesday :00am to 6:00pm GMT+ Thursday :00am to 1:00pm GMT+ D-Link Middle East & North Africa D-Link Technical Support over the Internet: http://support.dlink-me.com email:support@dlink-me.com
Technical Support
You can find software updates and user documentation on the D-Link website.
Tech Support for customers within South Africa and Sub Sahara Region:
D-Link South Africa and Sub Sahara Technical Support over the Telephone: +7-1-665-165 0600 DLINK ( For South Africa only ) Monday to Friday :0am to :00pm South Africa Time D-Link Technical Support over the Internet: http://www.d-link.co.za email:support@d-link.co.za
You can find software updates and user documentation on the D-Link website.
Technical Support
DIR-100
Ethernet- DSL- Windows, Macintosh, Linux Ethernet Internet Explorer 6.x , Netscape Navigator 7.0
D-Link DIR-100
CD-ROM
Ethernet- 5
- , .
6
Power : .
Status , DIR-100 .
WAN WAN. .
7
Reset , .
A. , DIR-100 . Power , , . B. 1. DSL- ; on/off . DIR-100 , . 2./DSL () DIR-100 1) (). Ethernet Ethernet, . , Ethernet , /DSL , on/off . 3./DSL () DIR-100 (). Ethernet- WAN DIR-100. WAN . , , B1 . C. Ethernet LAN1 DIR-100 Ethernet , DIR-100. LAN1 . : LAN DIR-100 Auto-MDI/MDIX. LAN . D. , Ethernet Gigabit Ethernet, DIR-100. DFE-530TX DGE-530T PCI () .
0
Log In
Setup Wizard
1
Setup Wizard
Next
admin.
Next
Next
IP-
. , , .
PPPoE - 34 PPTP - 35 L2TP - 36 Big Pond - 37 IP- - 38
Next
IP-, : ( ).
Clone MAC Address M A C - . MAC- .
Next
39
PPPoE
PPPoE ( Point-toPoint Protocol over Ethernet), .
Next
IP- , , .
Next
: , PPPoE , .
39
PPTP
PPTP (Point to Point Tunneling Protocol), .
Next
I P - , IP , PPTP , .
Next
39
5
L2TP
LTP (Layer Two Tunneling Protocol), .
Next
IP , IP- L2TP, , .
Next
39
6
Big Pond
, Telstra BigPond .
Next
, .
Next
43
7
IP-
IP-, , .
Next
. .
Next
39
Restart
-
Home. Web- (.. Internet Explorer Netscape Navigator). Web- . Advanced, Tools, Status Web-; , -.
IP- .
OK
0
Apply Now ( ).
1
- D-Link. D-Link . D-Link . D-Link: (5) 7-00- http://www.dlink.ru email: support@dlink.ru
D-Link DIR-100
Adaptador de Poder
Power Led Una luz fija indica conexin apropiada con el toma corriente.
Status Led Un parpadeo de luces indica que el DIR-100 esta funcionando apropiadamente.
Local Network Led Una luz fija en cada puerto indica la conexin de un dispositivo. Este Led parpadea durante la transmisin de datos.
WAN Led Una luz fija indica una conexin al puerto WAN. Este Led parpadea durante la transmisin de datos.
5
Puertos LAN Estos son para conectar los cable Ethernet a los computadores con Ethernet Disponible.
Puerto WAN Esto es para conectar un cable Ethernet a su MODEM DSL o CableModem.
Boton Reset Presionando este botn restaura el router a los valores de Fabrica.
Receptor de Poder
6
Instalacion de Hardware
Instalacion de Hardware
A. Primero, conecte el adaptador de poder al receptor que se encuentra en el panel posterior del DIR-100 y luego enchufe el otro extremo en el toma corriente de pared o alargador. El Led POWER se encender para indicar que esta funcionando apropiadamente. B. 1. Apague su MODEM DSL; Algunos dispositivos no tiene interruptor de encendido y/o apagado, requieren que usted desenchufe el adaptador de pared. Ahora, el DIR-100 debe estar encendido cuando el MODEM Cable/DSL este apagado. . Con el MODEM Cable/DSL (apagado), y el DIR-100 (encendido) conecte un cable Ethernet al conector Ethernet que se encuentra en el MODEM Cable/DSL. Despus de conectar el cable Ethernet, Encienda el MODEM Cable/DSL prendiendo la unidad o enchufando el adaptador de poder. . Con el MODEM Cable/DSL (encendido), y el DIR-100 (encendido), conecte el otro extremo del cable ethernet al puerto WAN en el panel posterior del DIR-100. El Led Wan se encender indicando una conexin apropiada.SI el Led WAN no se enciende, por favor vuelva al paso B1 y repita las instrucciones. C. Conecte un cable Ethernet al puerto LAN 1 en la parte posterior del DIR-100 y en un puerto Ethernet disponible en el adaptador de red en el computador que usted utilizar para configurar el DIR100. La luz del Led LAN 1 se encender para indicar una conexin apropiada. Nota: Los puertos LAN del DIR-100 son Auto MDI/MDIX. Significa que usted puede utilizar cable Ethernet Directo o Cruzado en los puertos LAN. D. Computadores equipados con adaptadores Ethernet o Gigabit Ethernet que deben ser conectados al DIR-100. Los adaptadores PCI DFE-50TX o DGE-50T (Por ejemplo) pueden ser conectados al Router sin ningn tipo de configuracin adicional requerida.
7
Comenzando
Comenzando
Configuracin
Configuracin
Esta seccin le enseara como configurar su Nuevo Router D-Link DIR-100 utilizando el asistente de Configuracin D-Link.
Abra su explorador de Internet e Ingrese la IP por defecto en la barra de direcciones "1.16.0.101" Luego presione el Botn ENTER o RETURN para continuar.
Click en Log In
Configuracin
Click en Next
Usted tiene la opcin para establecer una contrasea para el nombre de usuario Admin.
Click en Next
Click en Next
50
Configuracin
Direccin IP Dinmica
Deber seleccionar el tipo de conexin a Internet para su router, si no est seguro que tipo de conexin debe seleccionar, contctese con su proveedor de servicios de Internet.
PPPoE - Pagina 5 PPTP - pagina 5 LTP - pagina 5 Big Pond - pagina 55 Direccin IP esttica - pagina 56
Click en Next
Click en Next
Continua en pagina 57
51
Configuracin
PPPoE
Si su ISP utiliza PPPoE (Protocolo punto a punto sobre Ethernet), seleccione la opcin correspondiente.
Click en Next
SI usted tiene una conexin con IP dinmica, ingrese el nombre de usuario y contrasea entregado por su ISP.
Click en Next
Nota: Por favor, asegrese de quitar todos los programas de cliente PPPoE instalados en sus computadores.
Continua en pagina 57
5
Configuracin
PPTP
Si su ISP utiliza PPTP (protocolo punto a punto por tunel), seleccione la opcin correspondiente.
Click en Next
Si usted tiene una conexin con direccin IP dinmica, ingrese la IP del servidor, cuenta PPTP, y contrasea entregada por su ISP.
Click en Next
Si usted tiene una conexin con Direccin IP esttica, ingrese la direccin IP, Mascara de Subred, puerta de enlace, IP del servidor, cuenta PPTP, y contrasea entregada por su ISP.
Click en Next
Continua en pagina 57
5
Configuracin
L2TP
Si su ISP utiliza LTP (protocolo tnel capa ), seleccione la opcin correspondiente.
Click en Next
Si usted tiene una conexin con direccin IP dinmica, ingrese la IP del servidor LTP, Nombre de Usuario y contrasea entregada por su ISP.
Click en Next
Si usted tiene una conexin con Direccin IP esttica, ingrese la direccin IP L2TP, Mscara de Subred, puerta de enlace, IP del servidor LTP, Nombre de usuario y contrasea entregada por su ISP.
Click en Next
Continua en pagina 57
5
Configuracin
Big Pond
Seleccione esta opcin si usted se conecta a Internet a travs de Telstra BigPond Cable Broadband en Australia.
Click en Next
Click en Next
Continua en pagina 57
55
Configuracin
Click en Next
Ingrese la direccin IP entregada originalmente por su ISP. Usted necesita completar toda la informacin en los campos requeridos.
Click en Next
Continua en pagina 57
56
Configuracin Inalambrica
Click en Restart
57
Apndice
Apndice
Para conectar a la Red, asegrese que el adaptador de Red de su computador este configurado apropiadamente. Aqu se muestra como configurar su adaptador de Red para obtener una direccin IP automticamente utilizando el Router DIR-100. Para Microsoft Windows XP: Presione click derecho sobre el icono mis sitios de red y seleccione propiedades. Presione click derecho en el icono conexiones de Red asociado con el adaptador de red y selecciones propiedades (Ej. D-Link DFE-50TX+).
Click en Protocolo de Internet (TCP/IP) y luego presione Propiedades. Click en OK
Click en OK
5
Apendice Para Apple Macintosh OS X: Vaya al men Apple y haga clic en Preferencias del Sistema, y seleccione Network.
Click en Network
La informacin de Direccin IP, la mscara de subred, la direccin IP del Router y la direccin del adaptador aparecer.
5
Asistencia Tcnica
D-Link Latin Amrica pone a disposicin de sus clientes, especificaciones, documentacin y software mas reciente a travs de nuestro Sitio Web www.dlinkla.com El servicio de soporte tcnico tiene presencia en numerosos pases de la Regin Latino Amrica, y presta asistencia gratuita a todos los clientes de D-Link, en forma telefnica e internet, a travs de la casilla soporte@dlinkla.com
Soporte Tcnico Help Desk Argentina: Telfono: 000-6661 Lunes a Viernes 0:00 am a :00 pm
Soporte Tcnico Help Desk Colombia: Soporte Tcnico Help Desk Ecuador:
Telfono: 0100-70015 Lunes a Viernes 07:00 am a 0:00 pm Telfono: 100-777 711 Lunes a Viernes 07:00 am a 0:00 pm
Soporte Tcnico Help Desk El Salvador: Soporte Tcnico Help Desk Guatemala: Soporte Tcnico Help Desk Panam: Soporte Tcnico Help Desk Per:
Telfono: 00-617 Lunes a Viernes 06:00 am a 1:00 pm Telfono: 100-00 0017 Lunes a Viernes 06:00 am a 1:00 pm Telfono: 000-560 01 Lunes a Viernes 07:00 am a 0:00 pm Telfono: 000-50 Lunes a Viernes 07:00 am a 0:00 pm
Requisitos do Sistema
Requisitos do Sistema
Modem Ethernet Cable ou DSL Computadores com Windows, Macintosh, ou Linux com adaptador Ethernet instalado. Internet Explorer 6.x e Superior, ou Netscape Navigator 7.0 e superior.
Contedo da Embalagem
D-Link DIR-100
Adaptador de Energia
Se algum desses tens estiver faltando, favor entrar em contato com a sua revenda.
6
Visualizando Hardware
Visualizando Hardware
LED Power Este LED aceso indica conexo apropriada com a fonte de energia.
LED Status Este LED piscando indica que o DIR-100 est funcionando adequadamente.
LEDs Local Network O LED aceso em cada porta indica conexo ativa com um equipamento Ethernet. Estes LEDs piscam durante a transmisso de dados.
LED WAN Esse LED aceso indica que conexo na porta WAN. Este LED pisca durante a transmisso de dados
6
Visualizando Hardware
Portas LAN Estas so as conexes para serem usadas com cabos Ethernet.
Porta WAN Esta a conexo para o seu Cable/ ModemDSL baseados em Ethernet.
Boto Reset Pressionando este boto o Roteador ir restaurar as configuraes originais de fbrica.
Receptor de Energia
6
Instalao do Hardware
Instalao do Hardware
A. Primeiro, conecte o adaptador de energia ao receptor no painel traseiro do DIR-100, conecte a outra extremidade do cabo em uma tomada de parede ou estabilizador. O LED Power ir acender para indicar operao apropriada. B. 1. Desligue o seu Cable/Modem DSL; alguns equipamentos no possuem chave liga/desliga, e precisam ser desligados diretamente no adaptador. Agora, o DIR-100 poder ser ligado e o Cable/Modem DSL dever permanecer desligado. . Cable/Modem DSL (Desligado) DIR-100 (Ligado) Conecte o cabo Ethernet a uma porta Ethernet localizada no Cable/ Modem DSL. Depois que o cabo Ethernet estiver seguramente conectado, ligue o Cable/Modem DSL ligando atravs do boto, ou re-conectando o adaptador de energia. . Cable/Modem DSL (Ligado) DIR-100 (Ligado) Insira a outra extremidade do cabo Ethernet PORTA WAN no painel traseiro do DIR-100. O LED WAN ir se iluminar para indicar operao apropriada. Se o LED WAN no se iluminar, por favor volte ao passo B1, e repita as instrues. C. Insira um cabo Ethernet porta LAN 1 no painel traseiro do DIR-100, e a outra extremidade em uma porta Ethernet de um computador, que ser usado para configurar o DIR-100. O LED da porta 1 ir piscar para indicar operao apropriada. Nota: As portas LAN do DIR-100 so Auto-MDI/MDIX. Isso significa que voc pode usar um cabo Ethernet direto ou crossover nas portas LAN. D. Computadores equipados com adaptadores Ethernet ou Gigabit Ethernet podero se conectar ao DIR-100. Os adaptadores PCI (por exemplo DFE-50TX ou DGE-50T), podero se conectar ao Roteador sem nenhuma configurao adicional.
65
Diagrama da Soluo
Diagrama da Soluo
66
Configurao
Configurao
Nesta seo voc ver como configurar seu Roteador DIR-100 usando o D-Link Setup Wizard.
Abra seu Web browser e digite http://1.16.0.1 na caixa de endereos URL. Pressione Enter.
Digite admin como nome de usurio (username) e deixe o campo de senha (password) em branco.
Clique em Log In
67
Configurao
Clique em Next
Clique em Next
Clique em Next
6
Configurao
Endereo IP Dinmico
Voc ser informado sobre as opes de conexo do Roteador. Se voc no souber qual escolher, por favor entre em contato com o seu Provedor de Servios de Internet (ISP).
PPPoE - pag. 70 PPTP - pag. 71 LTP - pag. 7 Big Pond - pag. 7 Endereo IP Esttico - pag. 7
Clique em Next
Se voc selecionou Endereo IP Dinmico, esta tela ir aparecer: (Usado para maioria dos Servios de Internet a Cabo).
Clique no boto Clone MAC Address para copiar automaticamente o endereo MAC do adaptador rede em seu computador. Voc pode digit-lo manualmente no campo MAC address.
Clique em Next
Continuao na pgina 75
6
Configurao
PPPoE
Se o seu ISP utilize PPPoE (Point-to-Point Protocol over Ethernet), selecione a opo correspondente.
Clique em Next
Se voc possui uma conexo de IP Dinmico , coloque o usurio e senha fornecidos pelo seu ISP.
Clique em Next
Nota: Favor remover qualquer software cliente PPPoE existente, que esteja instalado em seu computador.
Continuao na pgina 75
70
Configurao
PPTP
Se o seu utiliza PPTP (Point to Point Tunneling Protocol), selecione a opo correspondente.
Clique em Next
Se voc possui uma conexo de Endereo IP Dinmica, coloque o endereo IP do servidor, e a conta PPTP fornecida pelo seu ISP.
Clique em Next
Se voc possui uma conexo de endereo IP Esttico, coloque o endereo IP, Mscara de SubRede, IP do Gateway, IP do Servidor, a conta PPTP, e a senha fornecida pelo seu ISP.
Clique em Next
Continuao na pgina 75
71
Configurao
L2TP
Se o seu ISP utiliza LTP (Layer Two Tunneling Protocol), selecione a opo correspondente.
Clique em Next
Se voc possui uma conexo de IP Dinmico, entre com o IP do Servidor LTP, Usurio, e a Senha, fornecidos pelo seuISP.
Clique em Next
Se voc possui uma conexo de IP esttico, entre com o IP do seu Servidor LTP, Mscara de Sub-rede,IP do Gateway, IP do Servidor LTP,usurio e a senha fornecidos pelo seu ISP.
Clique em Next
Continuao na pgina 75
7
Configurao
Big Pond
Selecione esta opo se voc conecta atravs de Telstra BigPond Cable Broadband na Austrlia.
Clique em Next
Clique em Next
Continuao na pgina 75
7
Configurao
Endereo IP Esttico
Se o seu ISP requer um Endereo IP Esttico, por favor selecione o boto com a opo correspondente.
Clique em Next
Entre com o Endereo IP fornecido pelo seu ISP. Voc ter que completar todos os campos necessrios.
Clique em Next
Continuao na pgina 75
7
Configurao Wireless
Clique em Restart
75
Apndice
Apndice
Para conectar a rede, certifique-se que o adaptador de rede do seu computador esteja configurado corretamente. Nesta seo voc ver como configurar o seu adaptador de rede para obter um endereo IP automaticamente, usando o Roteador DIR-100 com DHCP. Para Microsoft Windows XP: Clique com boto direito em Meus Locais de Rede e selecione Propriedades. Clique com o boto direito em Conexes de Rede associado com o seu adaptador Ethernet e selecione Propriedades (Ex.: D-Link DFE-50TX+).
Clique em Protocolo de Internet (TCP/IP) e depois em Propriedades. Clique em OK
Clique em OK
76
Apndice Para Apple Macintosh OS X: V em Apple Menu, clique sobre System Preferences, e selecione Network.
Clique em Network
As informaes de endereo IP,Mscara de Sub-Rede, Endereo IP do Roteador, e o Adaptador Ethernet devero aparecer.
77
Suporte Tcnico
Voc pode encontrar atualizaes de software e documentao de usurio no site da D-Link Brasil www.dlinkbrasil.com.br. A D-Link fornece suporte tcnico gratuito para clientes no Brasil durante o perodo de vigncia da garantia deste produto.
Telefone
DIR-100
D-LinkDIR-100
( )
CAT5
AC100~120V60Hz DC5V/2.5A
0
Power
Status StatusDIR100
Local Network
1
LAN
A. DIR-100 B.1. Adsl/Cable DIR-100Adsl/Cable 2. Adsl/Cable()DIR-100 () Adsl/Cable Adsl/Cable 3. Adsl/Cable()DIR-100 () DIR-100 WAN WAN WAN C.DIR-100DIR-100 (LAN)
Note:DIR-100(LAN)Auto-MDI/MDIX
D.PC10/100MbpsGigabitDIR100DFE-530TXDGE-530TPCI DIR-100
DIR-100
DIR-100
D-LinkD-LinkDIR-100Router
http://192.168.0.1 Enter
admin
Log In
Setup Wizard
5
Setup Wizard
Next
admin
Next
Next
6
Next
DynamicIPAddress :(Cable)
Next
93
7
PPPoE
PPPoE (Point-to-Point Protocol overEthernet)PPPoE
Next
ISP
Next
Note : PPPoE
93
PPTP
PPTP (Point to Point Tunneling Protocol )PPTP
Next
ISP PPTP
Next
ISP PPTP
Next
93
L2TP
L2TP (LayerTwoTunnelingProtocol )L2TP
Next
ISP L2TP
Next
ISP L2TP
Next
93
0
Big Pond
Australia TelstraBigPondCableBroadband
Next
ISP
Next
93
1
ISP IP "correspondingradio"
Next
ISP
Next
93
Restart
DIR-100Home (InternetExplorerorNetscapeNavigator)
DIR-100 AdvancedToolsStatus
Microsoft Windows XP :
IP
OK
Router
Apply Now ()
5
8:30a.m.7:00p.m Web:http://www.dlinktw.com.tw/ FAQ:http://www.dlinktw.com.tw/suppFaq.asp Email:dssqa_service@dlinktw.com.tw Phone:0800-002-615 D-Link http://www.dlinktw.com.tw/suppFaq.asp