Professional Documents
Culture Documents
HomeSafe's unique passive infrared system concentrates on the protected area you select. The motion detector monitors the area and responds only when a person moves into the protected area ....and then turns on the alarm. In the Entry Chime mode, the chime will Ding each time motion is detected.
5. If the unit messes up during the programming procedure, becomes abnormal, or if you forgot the "PASSWORD", take out the battery and wait for about 3 minutes for unit to reset, replace the battery. The system will reset to the initial normal state for you to re-program. 6. The unit can provide valuable protection for your home and property if utilized properly. However, this unit cannot guarantee complete protection against burglary or robbery, therefore, we will not be held responsible for any loss or damages which could occur.
(Fig. 2)
(Fig. 4)
Or, as an option, you can USE Velcro (not included) to install the unit anywhere you see fit. We suggest that you mount the unit at between 31o 6.5 ieet (1 to 2 meter) above the iVoor for best coverage of protection area. Adjust the sensor head to left, or right for the best direction of your detection area. 5. For shelf-top Turn the sensor head clockwise to 180 degrees to the back, then tum the head upwards to the desired angle. Place it on the shelf-top location you selected. (Fig. 3)
Motion sensor detects motion & activates alarm. Programmable security code and entry delay timing. Adjustable sensor head. Built-in high output 105dB alarm. Alarm/door chime option. Panic button. Program & low batteiy indicator. Verification tone for key pad and amVdisarm. 9V battery operated (battery not included) & AC adaptor compatible.
1. Remove the screw from battery compartment cover, slide it down to remove the cover. 2. Install an alkaline 9 Volt battery. (Fig. 1)
To connect optional accessories The unit provided with four termiinals to connect the optional accessories (Fig. 5). You can purchase following optional components to expand the functions of the unit. 1. Model 5100 Slave Unit Motion Detector 2. S-01 Magnetic Sensor Pack 3. Model T-012 Emergency Auto Dialer 4. 515SK/E Outdoor 120dB Siren
Connect to 3-01
For details please refer to the accessory manual you purchased. 3. Replace the battery cover and replace the screw. 4. For wall mount Using the battery cover as a template, mark locations of holes and install anchors and screws. Place the unit over the screws and slide the unit down to secure in place. (Fig. 2) (2)
6. To use AC adaptor ( Not included) Use the AC adaptor with output 9 Volt DC 200 MA with a 3.5 mm diameter male plug, center positive (+) and plug into the adaptor jack on the side of the unit. (Fig. 4) (3)
NOTE: The secunty code is initially factory - set at "0-0-0" when you first put in the battery. You can program your own security (up to 6 digits). If more than 6 digits are entered, you will hear an error tone. (4)
(1)
1. To program security code after battery installation: (A) Press the digits "0-0-0" (B) Press the "PROG" button. (C) Enter your new code number. (1-6 digits). (D) Press the "PROG" button again. 2. To change existing code to a new code: (A) Enter the old code number. (B) Press the "PROG" button. (C) Enter your new code number (1-6 digits). (D) Press the "PROG"button again. 3. To program the alarm timing: (A) Press "PROG" button. (B) Press one of number "1", "2" or "3" for different timing. "1 "=30 seconds alarm 2 cycles, 30 seconds rest in between. (Preset timing) "2"= 60 seconds alarm 2 cycles, 30 seconds rest in between. "3"= 90 seconds alarm 2 cycles, 60 seconds rest in between. 4. To program the entry delay timing: (A) Press "PROG" button. (B) Press one of number "7", "8" or "9" for different timing. "7" = 15 seconds delay. (Preset timing) "8" = 8 seconds delay. "9" = 0 seconds delay. (Instant alarm) REMARKS: The programming can only be operated during disarm mode. When unit is in arm mode, no programming is allowed for added protection.
NOTE: Make sure to switch off the chime switch before arming. There wi41 be a beep after 80 seconds sensor warm-up and exit delay after arming the unit. 2. TO DISARM THE UNIT (A) Enter your security code (B) Press "DtSARM", you wi41 hear one beep to confirm disarming. 3. DOOR CHIME ON/OFF (A) Slide the chime switch to "ON" (B) Wait for 60 seconds after a beep for the sensor to "WARM-UP". Then when human movement is detected, it will sound "DING DONG" chime. (C) Slide the switch to "OFF" to turn the chime function off. NOTE: When unit is in arm mode, the chime wi/l not function. 4. PANIC BUTTON (A) Press "PANIC" button to trigger alarm immediately for 30 seconds. (B) To stop the alarm, just enter your security code and press "DISARM".
ome afe^
MOTION DETECTOR WITH SECURITY ALARM
MODEL 125A
^ i ^ ^
1 2 3 '' ^. 5 s ^^.
a_
7' 8 9 r^
OPERATION
TO ARM THE UNIT (A) Enter your security code (or "0-0-0", if you did not change the code). (B) Press "ARM", you will hear 3 short beeps to confirm 'ARMED" (5)
aqra ^ O Dis c ^I -
(7)