Professional Documents
Culture Documents
Design an addressing scheme and fill in the Addressing Table based on the following requirements: a. Subnet the address space 10.10.10.0/24 to provide 40 host addresses for LAN 1 while wasting the least amount of address space. b. Assign the first available subnet to LAN 1. c. Assign the lowest (first) host address in this subnet to the Fa0/0 interface on HQ. d. Assign the second address in this subnet to the VLAN 1 interface on S2. e. Assign the highest (last) host IP address in this subnet to NetAdmin.
Use HQ as the router name. Use class as the encrypted password for privileged EXEC mode. Require password-protected logins for the console line. Use cisco as the password. Require password-protected logins for the vty lines. Use cisco as the password. Configure the banner message-of-the-day as Unauthorized access is prohibited.
b. Configure the two Fast Ethernet interfaces: Configure the router interfaces according to your completed Addressing Table. Configure each interface with a description.
d. Configure interface VLAN 1. e. Configure the default gateway. f. Test that S2 is able to ping the default gateway.
Step 2: Configure HQ. Press RETURN to get started! Router>enable Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)#hostname HQ HQ(config)#enable secret class HQ(config)#line console 0 HQ(config- line)#password cisco HQ(config- line)#login HQ(config- line)#exit HQ(config)#line vty 0 4 HQ(config- line)#password cisco HQ(config- line)#login HQ(config- line)#exit HQ(config)#banner motd #Unauthorized access is prohibited.# HQ(config)#interface fastEthernet 0/0 HQ(config- if)#ip address 10.10.10.1 255.255.255.192 HQ(config- if)#description LAN1 HQ(config- if)#no shutdown HQ(config- if)# %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up HQ(config- if)#exit HQ(config)#interface fastEthernet 0/1 HQ(config- if)#ip address 10.10.10.65 255.255.255.248 HQ(config- if)#description LAN2
HQ(config- if)#no shutdown HQ(config- if)# %LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up HQ(config)# Step 3: Configure S2 and Verify Connectivity. Switch>enable Switch#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#hostname S2 S2(config)#enable secret class S2(config)#line console 0 S2(config- line)#password cisco S2(config- line)#login S2(config- line)#exit S2(config)#line vty 0 4 S2(config- line)#password cisco S2(config- line)#login S2(config- line)#exit S2(config)#banner motd #Unauthorized access is prohibited.# S2(config)#interface vlan 1 S2(config- if)#ip address 10.10.10.2 255.255.255.192 S2(config- if)#no shutdown S2(config- if)# %LINK-5-CHANGED: Interface Vlan1, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up
S2(config- if)#exit S2(config)#ip default-gateway 10.10.10.1 S2(config)#exit S2# %SYS-5-CONFIG_I: Configured from console by console S2#ping 10.10.10.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.10.10.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 31/34/47 ms