ZTE Indonesia Mid Plaza 2 15 th floor By Rudy Kusuma Setiadi Ass Maintenance Engineer Main Job During Probation My first duty in Lampung with Mr. Luo Li Tao Try to debug BSC in Lampung
SWITCH 2950 BSC SERVER switch port 3 (vlan2) from L4-12(RMPB)-OMC2 (Cabinet 1) switch port 4 (vlan2) from L4-11(RMPB)-OMC2 (Cabinet 1) switch port 5 (vlan2) from L4-9(RUIM2)-FE7 (Cabinet 1) SWITCH PORT 13 (vlan3) from L6-4(RMNIC)-FE1 (Cabinet 1) SWITCH PORT 14 (vlan3) from L6-3(RMNIC)-FE1 (Cabinet 2) SWITCH PORT 21 (vlan4) from L6-4(RMNIC)-FE2 (Cabinet 1) SWITCH PORT 22 (vlan4) from L6-3(RMNIC)-FE2 (Cabinet 2) switch port 6 (vlan2) from L4-15(RUIM2)-FE7 (Cabinet 2) Switch port 24 (vlan1) from MGW server port 24 Swtich port 9 (vlan2) from BSC ALARM Switch port 11 (vlan2) from client 1 Switch port 12 (vlan2) from client 2 Switch port 10 (vlan2) from CPU server 1 Switch port 15 (vlan3) from MPLS port 16 (PDSN) Switch port 23 (vlan3) from router 2600 Switch port 19 (vlan4) from CPU server 2 3 4 6 5 10 9 12 11 14 13 15 19 21 22 23 24 Router 2600 BSC Server Router 2600 from MPLS DCN port 17 Router 2600 from switch 2950 port 23 OMP module <-> use straight Client <-> switch use stright Router <-> switch use stright Switch <-> switch use cross Alarm box <-> switch use straight Straight : White orange, orange, white green, blue, white blue, green, white brown, brown Remote Fe0/0 Fe0/1 BSCB ROUTER MPLS MGW SWITCH 23 trunk 24 vlan 10 trunk BSCB SWITCH 24 trunk 1 vlan 10 BSCB SERVER 1 OPTIC FIBER
OPTIC FIBER
BUSN 1 & 2 BUSN 3 BUSN 4 GLIQV CLKG
X40 X47 Pin 1 & 2 had jumper. It mean resistance 75 ohm 1 2 3 CLKG
X40 X47 Now Pin 2 & 3 had jumper. It mean resistance 120 ohm 1 2 3 DTB
S1 S2 S3 S4 S6 S5 S12 S9 S7 S8 S10 S11 S1, S2, S3, S4, S5, S6, S7, S8, S9, S12 all 4 pin must off S10, S11 all 4 pin must on RDTB All jumper must take off TRIB ID, RACK ID & SHELF ID CABINET 1 RACK 1,2,3
BEFORE AFTER BEFORE AFTER 1110 (Lampung ID) 0000 (Cabinet 1) 0000 (shelf 1) 1000 (shelf 2) 0100 (shelf 3) TRIB ID, RACK ID & SHELF ID CABINET 2 RACK 1 & 2
BEFORE AFTER BEFORE AFTER 1110 (Lampung ID) 1000 (Cabinet 2) 0000 (shelf 1) 1000 (shelf 2) 0100 (shelf 3) Rack switcher
32 E1 1 DTB module had 32 E1 (10 11 11) And BSC had 4 module DTB It means there are 128 E1 E1 from DTB module
CLIENT CONSOLE
1.Choose application. 2.Choose configuration management. 3.Right click OMMR_3G[100007][Bandar Lampung] and choose add BSS 4.Choose for device id : 7 and device alias : Bandar Lampung 5.Right click BSSB[7][Bandar Lampung] and choose add BSC system Module of Rack 1
1.Right click physical configuration and choose add ip rack. 2.Fill for rack :1 and rack type : ip rack 3.Right click IP Rack[1] and fill shelf : 1 and shelf type : BUSN shelf 4.Right click IP Rack[1] and fill shelf : 2 and shelf type : BCTC shelf 5.Right click IP Rack[1] and fill shelf : 3 and shelf type : BUSN shelf 6.Right click IP Rack[1] and fill shelf : 4 and shelf type : GCM shelf Configuration module of rack 1 shelf 2
1.Right click shelf 2 port 9 (UIM) and choose add board then choose for B type : BT_3G_UIM_2 2.Right click shelf 2 port 10 (UIM) and choose add board then choose for B type : BT_3G_UIM_2 3.Right click shelf 2 port 11&12 (MPl2) and choose add board then choose at MP board for B type : BT_3G_WPBCB at MP board 4.Right click shelf 2 port 11 (MPl2) and choose configure module type then fill module 1 for MT_3G_OMP and fill module 2 for MT_3G_RPU 5.Right click shelf 2 port 13 & 14 (CLKG) and choose add board then choose for B type : BT_3G_CLKG 6.Right click shelf 2 port 15 & 16 (CHUB) and choose add board then choose for B type : BT_3G_CHUB 7.Right click shelf 2 port 1 & 2 (SPCFMP) and choose add board then choose for Logic type : UT_3G_BSC_SPCF_MP 8Right click SPCFMP and choose config module type and choose MT_3G_CMP_HRPD 9.Right click shelf 2 port 3 & 4 (MPl2) and choose add board then choose at MP board for B type : BT_3G_WPBCB at MP board 10.Right click shelf 2 port 3 (MPl2) and choose configure module type then fill module 3 for MT_3G_DSMP_HDMP and fill module 4 for MT_3G_CMP_HDMP 11.Right click shelf 2 port 5 & 6 (MPl2) and choose add board then choose at MP board for B type : BT_3G_WPBCB at MP board 12.Right click shelf 2 port 5 (MPl2) and choose configure module type then fill module 3 for MT_3G_RMP and fill module 4 for MT_3G_CMP_HDMP 13.Right click shelf 2 port 9 (UIM) and choose configure MDM type then fill in all MDM type (call, hand off, HRPD trnsmitt, paging respond, register) 15.Right click all module and choose config module / unit relationship Configuration of module rack 1 shelf 1
1.Right click port 9 & 10 and choose add board then choose UT_3G_UIM_T_GXS (Logic type) ; BT_3G_UIM_2 (B type) 2.Right click port 1 & 2 and choose add board then choose UT_3G_DTB (Logic type) 3.Right click port 3,4,5,6,7,8 & 11 and choose add board then choose UT_3G_IWFB (Logic type) 4.Right click port 12,13 & 14 and choose add board then choose UT_3G_VTC_DSP16 (Logic type) 5.Right click port 15 and choose add board then choose UT_3G_SPB_8260 (Logic type) 6.Right click port 16 and choose add board then choose UT_3G_SDU_PPC775_BSS (Logic type) 7.Right click port 17 and choose add board then choose UT_3G_SDU_PPC775_HRPD (Logic type) (for EVDO services) Configuration of module rack 1 shelf 3
1.Right click port 9 & 10 and choose add board then choose UT_3G_UIM_T_GXS (Logic type) ; BT_3G_UIM_2 (B type) 2.Right click port 7 and choose add board then choose UT_3G_ABPM_1200_FE8_MHPC (Logic type) 3.Right click port 7 and choose 1+1 back up mode for add port 8 4.Right click port 1 and choose add board then choose UT_3G_DTB (Logic type) 5.Right click port 3 and choose board then choose UT_3G_IPCF_1200_FE8 (Logic type) 6.Right click port 3 and choose 1+1 back up mode for add port 4 7.Right click port 5 & 6 and choose board then choose UT_3G_UPCF_1200_FE8 (Logic type) 8.Right click port 15, 16 & 17 and choose add board then choose UT_3G_SDU_PPC775_BSS (Logic type) 9.Right click port 3 and choose configure A12A13 then choose A12 Configuration of module rack 2 shelf 1
1.Right click port 9 & 10 and choose add board then choose UT_3G_UIM_T_GXS (Logic type) ; BT_3G_UIM_2 (B type) 2.Right click port 1 and choose add board then choose UT_3G_DTB (Logic type) 3.Right click port 2, 8 & 12 and choose add board then choose UT_3G_IWFB (Logic type) 4.Right click port 12 and choose add board then choose UT_3G_VTC_DSP16 (Logic type) 5.Right click port 16 and choose add board then choose UT_3G_SPB_8260 (Logic type) 6.Right click port 17 and choose add board then choose UT_3G_SDU_PPC775_BSS (Logic type) 7.Right click all module and choose config module / unit relationship Configuration of module rack 2 shelf 2
1.Right click port 15 & 16 and choose add board then choose UT_3G_UIM_GCS (Logic type) ; BT_3G_UIM_2 (B type) 2.Right click port 7 & 8 and choose add board 3.Right click port 1 & 2 and choose UT_3G_GLIQV_USER (Logic type) Configure CMP & HMP
1.Right click physical configuration and choose configure CMP 2.Because of there were 2 CMP at shelf 2 port 3 & 4 so choose unit no 0-7 for module 4 and unit no 8-15 for module 6 1.Right click physical configuration and choose configure HMP 2.Select all unit no from 0-15 for module 100 Configure the connection between DSMP and RMP, modify A9 timing para & unify VTC workmode
1.Right click physical configuration and choose configure the connection between DSMP and RMP 2.Change Instance Num : 720 (on line user) 1.Right click physical configuration and choose modify A9 Timing Para 2.All data default 1.Right click physical configuration and choose unify VTC workmode 2.All data default Configure PCM at DTB module
1.Right click rack 1 shelf 1 port 1 (DTB) and choose configure PCM 2.Then add PCM from 0-31 ( E1 from 0-31) 3.Right click rack 1 shelf 1 port 2 (DTB) and choose configure PCM 4.Then add PCM from 32-63 (E1 from 0-31) 5.Right click rack 2 shelf 1 port 2 (DTB) and choose configure PCM 6.Then add PCM from 64-71 (E1 from 0-7) 7.And for DTB module, pick 4 PCM (right click at PCM and choose configuration relay) so there were 12 PCM which TS 16 use for signalling (so must delete TS 16) Configure Physical link 2 at SPB module
1.Right click rack 1 shelf 1 port 15 and choose configure physical link 2 2.SPB have 4 CPU and because there were 2 DTB so there was 8 CPU at rack 1 (change cpuid : 1-4 ; change DTE1 : 0-3 ; change DT unit : 1-2) 3.Right click rack 2 shelf 1 port 16 and choose configure physical link 2 4.SPB have 4 CPU and because there were 1 DTB so there was 4 CPU at rack 2 (change cpuid : 1-4 ; change DTE1 : 0-3 ) Configure GLI/UIM connection at GLI module 1.Right click rack 2 shelf 2 port 1 (GLI) and choose GLI/UIM connection 2.Connect GLI port : 0, subsystem : 6 to UIM rack 1 shelf 1 port 1 (subsystem 1) 3.Connect GLI port : 1, subsystem : 6 to UIM rack 2 shelf 1 port 1 (subsystem 5) 4.Connect GLI port : 2, subsystem : 6 to UIM rack 1 shelf 1 port 2 (subsystem 3) Configure SPCFMP
1.Right click rack 1 shelf 2 port 1 (SPCFMP) and choose SPCF CPU1 2.Choose configure PCF mode and choose pCF PCF 3.Right click rack 1 shelf 2 port 1 (SPCFMP) and choose SPCF CPU1 4.Choose configure PCF firewall and A10 Para 5.Fill in for PCF_A10 Value & SPCF Firewall IP :192.168.201.122 6.Right click rack 1 shelf 2 port 1 (SPCFMP) and choose SPCF CPU1 7.Choose connection between SPCF and PDSN (all data default) 8.Choose configure SPCF CPU1 and choose configure PCFSPI 9.Fill in SPI Value : 100 10.Fill in KeyCoding & KeyDecode : 1234567890ABCDEF
Configure the number of FE ports of IPCF 1.Right click rack 1 shelf 3 port 3 (IPCF) and choose configure ports number of FE (all data default) 2.Right click rack 1 shelf 3 port 3 (IPCF) and choose configure A12A13 then choose A12 Configure PDSN
1.Right click physical configuration and choose configure PDSN 2.Fill in IP address and broker Ip same as IP PDSN Jakarta (192.168.49.33) 3.Fill in name : PDSN 4.Fill in location : Jakarta 5.Fill in UDP port : 699 Configure IP Interface
1.Right click physical configuration and choose configure IP interface 2.Then choose UT_3G_BSC_SPCF_MP 3.Fill in IP address : 192.168.201.122 (A10) 4.Fill in Subnetmask and Broadcastaddr : 255.255.255.255 5.Fill in MAC : 00-D0-D0-A0-00-10 6.Then choose UT_3G_IPCF_1200_FE8 7.Fill in IP address : 192.168.201.124 (A8) 8.Fill in subnetmask : 255.255.255.0 9.Fill in Broadcastaddr : 255.255.255.255 10.Fill in MAC : 00-D0-D0-A0-00-9 Must input again for IPCF : 12.Fill in port : 2 13.Fill in IP address : 192.168.200.100 (A12) 14.Fill in MAC : 00-D0-D0-A0-00-11 Configure Static Route
1.Right click physical configuration and choose configure static route 2.Fill in route prefix : 192.168.49.0 3.Fill in next hope (MPLS Lampung) : 192.168.201.121 BSC configuration & MSC configuration
1.Goes to no. 7 signal and choose BSC configuration 2.Fill in network type : network8[8] 3.Fill in LAC of the network for local office : 30- 00-07-21 4.Fill in test code : 12345678000000 5.Fill in at 24 signalling point; Main signaling point : 6, Seed signalling point : 61, signaling point : 5 (free option) 6.Fill in at 14 signalling point; Main signaling point : 6, Seed signalling point : 61, signaling point : 5
1.Goes to no. 7 signal and choose MSC configuration 2.Fill in network type : network7[7] 3.Fill in Signaling Link Code; Main Signaling point : 6, Seed signaling point : 56, Signaling point : 5 4.Fill in test flag : Need tes[1] 5.Protocol type : CHINA[1] 6.Subsystem field : Domestic Signalling Link Code [8] MTP Configuration
1.Goes to MTP configuration and choose signal link set (data default) 2.Choose signal link Because there were 2 SMP module so: 3.Fill in link id : 1 - 12 4.Fill in SMP module id : 4 5.Fill in signalling link code : 0 - 11 So there was 12 signal for module id 4 6.Choose signal route (data default) 7.Choose signal office (data default) SSN Configuration
1.Choose SSN configuration 2.Add 10 times; office id 0 mean BSC and office id 1 mean MSC/MGW Radio configuration
1.Goes to radio configuration 2.Fill in CDMA channel frequency 0 : 201 (voice) 3.Fill in CDMA frequency 0bandclass : 800M[0] 4.Fill in CDMA channel frequency 1 : 242 (EVDO) 5.Fill in CDMA frequency 1bandclass : 800M[0]
BSS Para
1.Choose BSS para 2.Choose BSS parameter 3.Fill in market id : 1 4.Fill in switch number : 1 5.Fill in MS MCC : 510 (Indonesia) 6.Fill MS MNC : 03 (Indonesia) 7.Fill in MS IMSI_11_12 : 03 (Indonesia) 8.Fill in MSC support group CIC operator indicator : Not supported (0) A12 interface parameter at HRPD para 1.Choose HRPD para 2. Choose A12 interface parameter 3.Fill in AN IP address : 192.168.200.100 4.Fill in AAA IP address : 192.168.200.129 Access network parameter & user rank at HRPD para
1.Choose HRPD para 2.Choose access network parameter 3.Change system identification : 10817 4.Change network identification : 65535 1.Choose HRPD para 2.Choose user rank 3.Add 9 times (data default) Add BTS (BDS & RFS rack)
1.Right click BSSB[7][Bandar Lampung] and choose add BTS 2.Choose add IP BTS 3.Fill in system alias (BTS name) 1.Right click physical configuration and choose add BDS rack 2.Right click one of module and choose add subrack then choose add down subrack Add board for shelf 1 of BDS rack
1.Right click SAM board and choose add board then choose add SAM board 2.Right click GCM board and choose add board (2 board) 3.Right click CHM board and choose add board then choose CHM0 board 3,5. Right click CHM0 and choose configure CSM5000 and group id must 0 all 4.Right click CHM board and choose add board then choose CHM1 board (only for EVDO services) 5.Right click CCM board and choose add board (2 board) 6.Right click RIM board and choose add board (2 board) 7.Right click DSM0 board and choose add board then choose add DSM0 board 8.Right click GCM board and choose configure GCM receivable mode ( 1 board only) 9.Right click GCM board and choose configure CCB work mode 10.Right click CHM1 board and choose configure Rlm then fill in RevChips num : 4 (only for EVDO services) 11.Right click CHM1 board and choose configure Flm (data default) (only for EVDO services) Add board for shelf 1 of BDS rack
12.Right click DSM0 and configure HDLC then choose configure the Ts of HDLC (only for EVDO services) 13.Right click DSM0 and configure UID (only for EVDO services) 14.Right click DTB (BSC rack 1 shelf 3 port 1) and choose configure BSC HDLC then choose configure the Ts of HDLC (only for EVDO services) 15.Right click ABPM (BSC rack 1 shelf 3 port 7) and choose configure BSC UID then choose configure UID (only for EVDO services) 16.Right click ABPM (BSC rack 1 shelf 3 port 7) and choose configure the connection between BSC and BTS Add board for shelf 2 of BDS rack
1.Right click SAM board and choose add board then choose add SAM1 board 2.Right click TRX board and choose add board then choose add TRX board ( 3 board) 3.Right click RMMIE board and choose add board then choose add RMM0 board 4.Right click RMMIE board and choose configure connection between RIM and RMM Add board for shelf 3 & 4 of BDS rack
1.Right click RFEA board and choose add board then choose add RFEA board ( 3 board) 2.Right click PIM board and choose add board 3.Right click LPA board and choose board then choose DPA board (3 board) 4.Right click RFEA board and choose configure connection between TRX and RFE_PA then connect ( 3 board) 5.Right click DPA board and choose configure connection between TRX and RFE_PA then connect ( 3 board) Configure procedural address and configure UCFSN check at BTSB
1.Right click BTSB[1] and choose configure procedural address then add 2 times 1.Right click BTSB[1] and choose configure UcFSN check Add cell at radio configuration 1.Goes to radio configuration and fill in country code : 510 (only for EVDO services) 2.Right click radio configuration and choose add cell 3.Choose cell paramater 4.Fill in cell alias : name of BTS 5.Fill in system identification : 10817 6.Fill in network id : 65535 7.Location : 721 (local area Lampung) 8.CI : 14100 (based on planning) 9.PTT dispatch : 0 (random) 10.Pilot PN sequence offset index : 3 (based on planning) 11.Band class : 800M[0] 11.Pilot PN sequence offset index increment: 3 12.Search window size for the remaining set : 8
13.Choose system parameter 14.Fill in registration zone : 721 (local area Lampung) 15.Fill in base station id : 14100 (based on planning) 16.Fill in authentication mode : include authentication data (1) 17.Fill in random challenge value: 123456 (random) 18.Fill in offset of local time from system : 14 19. Fill in maximum slot cycle slot index : 1 Add new carrier at BSS channel
1.Right click BSS cell and choose add carrier then choose new carrier 2.Fill TRX element Id : 1 3.At carrier parameter, fill in carrier rated power (0.1dbm) : 400 3.Choose pilot channel (add with data default) 4.Choose sync channel (add with data default) 5.Choose page channel (add with data default) 6.Choose access channel (add with data default) HRPD Cell
1.Choose HRPD cell then choose Cell parameter 2.Fill in cell alias : name of BTS 3.Fill in Pilot PN : 3 (based on planning) 4.Fill in sector id : 0000000000000001 5.Fill in color code : 1 6.Choose cell state parameter 7.Fill in offset of the local time : 14 8.Choose sector hand off parameter 9.Fill in pilot PN sequence increment : 3 10.Right click HRPD cell and choose add carrier 11.Fill TRX element Id : 1 12.At carrier parameter, fill in carrier rated power (0.1dbm) : 400 13.Choose control channel (data default) 14.Choose acces channel (data default) 15.Choose forward traffic channel (data default) BSS Cell
1.Choose BSS cell and choose link cell (data based on planning) 2.Choose BSS carrier and choose neighbor cell list then fill in neighbor transmitt time offset (data based on planning) and fill in neighbor transmit time offset : 0 ALARM MANAGEMENT
Choose views and choose fault management then choose alarm management. At alarm management, we can know and check all module which had alarm or not. VERSION MANAGEMENT 1.Choose Views and choose System tools then choose version management. 2.Choose Version Func and choose Query Version then choose Query running information after that select the module. At version management, we can know the version type of all module RFS Attenuation Configuration 1.Choose views and choose System Tools then choose Dynamic Data Management 2.Choose RFS Attenuation Configuration
At here, we can know RFE transmission power and we can rise up & down transmission power with change attenuation control value (standard for Rfe transmission power is 38 dBm) DATA SYNCHRONIZATION
1.Choose configuration management 2.Right click OMM_3G and choose Data Sync
At Data Synchronization, after we had done something with module so we must synchronization data first SAVE CONTROL 1.Choose configuration management 2.Right click OMM_3G and choose Save control
At Save control, after we had done something with module so we can save control ALARM BOX Server IP : 129.168.7.10 Alarm IP : 129.168.7.254 Port : 6700 No 7 Signaling Link Choose Views->System Tools->Dynamic Data Management->Resource Observe- >MTP SIGNALINK->MTP LINKSET[1]->SMP[4] good No 7 Signaling Link Choose Views->System Tools->Probe->BSSB->BSCB- >BSC_CMP_HDMP[4]->select R_Office for Table Name- >View Table. good No 7 Signaling Link 1.Check first IP CMP (128.112.35.9) 2.Add your computer IP (ip address : 128.112.35.9 ; subnet mask : 255.0.0.0) 3. Use the command telnet 128.112.35.9 4.Log in : zte 5.Password : zte 6.WPBCB : ShowCallState
CONNECTION WITH JAKARTA IF NOT SUCCSESS : 1, Generally there one folder of 3GPlatOMC in the path of Release\ip\tool\ of the Server and client, open it and find 3GPLATWIN_MGT.ini. Open this file and modify 3 parameters as follows: SETUPCOMM=1 BoardIpAddr=129.168.7.1This IP address is OMC IP of OMP module which communicate with the server, must input it correctly. LocalIpAddr=IP address (If in the server, set it at random and just make it be same segment with BoardIpAddr, such as 129.168.7.20; but if in the client, this IP address must be same with the IP address of the client, such as 129.168.7.100). 2, Copy this modified 3gPlatWIN_MGT.ini file to the folder of WINDOWS in disk C:, but for win2000 system, this folder is WINNT. 3, Run 3GPLATWINNTTCP.exe, EXECUTEVC.exeINTERPRETPROC.exe TELSERVER.exe in order in the folder of 3GPlatOMC. (If system prompts that can not connect to the database, dont click OK and dont care.) Input telnet 127.0.0.1 in the Run window and enter the following interface.(Blue character need to input by ourselves.)
************************************************************ Welcome to the world of 3GPlatForm! ************************************************************ Username:root Password:no password 3GPlatForm>en 3GPlatForm#pro 3GPlatForm(config-protocol)#sh i i b Interface Stat Pro IP Mask 2:1:7:2:250 down down unassigned unassigned 1:1:14:1:1 down down unassigned unassigned 2:1:3:2:250 down down unassigned unassigned 2:1:1:1:250 up up 192.168.200.138 255.255.255.255 3:1:3:1:1 up up 192.168.200.140 255.255.255.0 3:1:3:1:2 down down unassigned unassigned 3:1:3:1:3 down down unassigned unassigned 3:1:3:1:4 down down unassigned unassigned 3:1:7:1:1 up up unassigned unassigned 3:1:7:1:2 up up unassigned unassigned 3:1:7:1:3 up up unassigned unassigned 3:1:7:1:4 up up unassigned unassigned 3:1:7:1:5 up up unassigned unassigned 3:1:7:1:6 up up unassigned unassigned 3:1:7:1:7 up up unassigned unassigned 3:1:7:1:8 up up unassigned unassigned 3:1:7:1:9 up up unassigned unassigned 3:1:7:1:10 up up unassigned unassigned 3:1:7:1:11 up up unassigned unassigned The meaning of interface is as follows, for example: 2:1:1:1:250 2subsystemcan see through double clicking SPCF module 1modulecan see in IP interface 1unitcan see through double clicking SPCF module 1sunitcan see through double clicking SPCF module 250local portcan see through double clicking SPCF module
MTP3 Signal Trace Choose Views System tools Dynamic Data Management Resource observe - BSSB Trunk PCM Block ( at check status ) MTP3 Signal Trace Choose Views System Tools Signal Trace Tool MTP3 Signal Trace Trace Set If direction send and receive, It means connection between BSC MGW MSC already good MTP3 Signal Trace
Alarm Query Choose Alarm Management Query Alarm
In Alarm Query, We can check if the problem still continuous or not Service Observation Choose Views System Tools Service Observation Set If we made call, so we can know ESN and IMSI number of handset Signal Trace Choose Signal Trace Tools BSS Signal Trace Trace Set
Fill in Trace type with Specify BTS.
After we can know IMSI and ESN phone number Signal Trace Choose Signal Trace Tools BSS Signal Trace Trace Set Put IMSI phone number first After that we can check signal trace Upgrade BSC module 1.Find 3GVER 18.16.04 folder -> release -> IP -> BSC & BTS folder 2.Put it into ZXOMC -> UMS -> UMS SVR -> Version 3.Choose add version : a. Choose BSC CPU WPBCB OMP 755 WPBCB b. Choose BSC FPGA WPBCB 040401 WPBCB c. Choose BSC CPU WPBCB RPU 755 WPBCB d. Choose BSC CPU WPBCB SPCF e. Choose BSC CPU WPBCB RMP f. Choose BSC CPU WPBCB CMP g. Choose BSC CPU DSMP HDMP h. Choose BSC CPU HMP - HDMP 4.Choose configure OMP a. Choose OMP Left, double click then choose 04 and right click choose configuration b. Choose OMP Right, double click then choose 04 and right click choose configuration c. Choose FPGA Left, double click then choose 04 and right click choose configuration d. Choose FPGA Right, double click then choose 04 and right click choose configuration Then reset both OMP at same time
5.Choose active version a. RPU b. HDMP_DSMP c. CMP_HDMP d. RMP e. CMP_HRPD f. BSC_SPCF Then reset all MP 6.Choose active version a.CPU/ UIM2/ MDM/ 755/ GCS b.CPU/ UIM2/ UIM/ 755/ GXS c.FPGA/ UIM2/ 040204/ UIM2/ FPGA Then reset all UIM module d.CPU/ DTB/ DTB/ 852/ DTB Then reset all DTB module e.CPU/ VTCD/ VTC/ 8260 f. DSP/ EVRC IND/ VTCD Then reset all VTCD module g.CPU/ WPBCA/ RLSASDU/ 755/ SDU BSS h. CPU/ WPBCA/ HSDU/ 755/ SDU- HRPD i. FPGA/ WPBCA/ 030800/ FPGA Then reset all SDU module
Upgrade BSC module 5.j. CPU/ SPB/ SPB/ 8260/ SPB8260 Then reset all module SPB k. CPU/ PSN/ PSN/ 860/ PSN4V Then reset all module PSN l. CPU/ MNIC/ UPCF/ BEARM/ UPCF Microcode m. CPU/ MNIC/ UPCF/ BEARM/ UPCF CPU Then reset all module UPCF n. CPU/ MNIC/ IPCF/ BEARM/ IPCF Microcode o. CPU/ MNIC/ IPCF/ BEARM/ IPCF CPU Then reset all module IPCF p. CPU/ MNIC/ ABPM/ BEARM/ ABPM Microcode q. CPU/ MNIC/ ABPM/ BEARM/ ABPM CPU r. CPU/ MNIC/ ABPM/ 755/ ABPM s.FPGA/ MHPC/ 031101/ FPGA Then reset all module ABPM t. CPU/ IWFB/ IWF/ 8250 u. DSP/ IWFB/ IWFB Then reset all module IWFB v. CPU/ GLIQV/ GLI/ XSCALE/ Microcode w. CPU/ GLIQV/ GLI/ XSCALE/ Microcode x. CPU/ GLIQV/ GLI/ XSCALE/ CPU2 y. CPU/ GLIQV/ GLI/ XSCALE/ CPU z. FPGA/ GLIQV/ 040202/ GLIQV Then reset all module
A. CPU/ CHUB/ CHUB/ 8245/ CHUB B. BTS/ MCU/ GCM1/ BSC GCM1 C. BTS/ FPGA/ TFS/ GCM1/ 00002 For B & C then choose deliver version and choose MCU and choose GCM Upgrade BTS module Upgrade BTS module a. Choose add version : 1. CPU/ CCM/ CCM/ 755/ CCM 2. CPU/ RMM/ RMM/ 8245/ RMM0 3. CPU/ CHM1X/ CHM1X/ 755/ CHM1X 4. CPU/ DSM/ 8245/ DSM 5. CPU/ TRX/ TRX/ 850/ TRX 6. MCU/ SAM/ SAM0 7. MCU/ GCM0/ GCM FPGA/ TFS/ GCM0/ D47/ GCM0 8. MCU/ RIM0/ RIM 9. MCU/ SAM1/ SAM1 10. MCU/ RFE_A/ RFE_A 11. MCU/ PIM/ PIM 12. MCU/ DPA/ DPA Upgrade BTS module 1.Choose Version management 2.Choose Deliver Version 3.Choose Create Deliver Task Monitor then choose cancel 4.Choose CPU first 5.Choose 5 modules (CCM, RMM, CHM1X, DSM, TRX) 6.Choose Mate Syn 7.Choose All IP board and cancel BTSA board 8.Choose only UT_CCM_BIN only 9.Choose active version then choose cancel 10.Choose BTS node 11.Choose All IP Control board 12.Choose activate CPU version 13.Choose active version then choose cancel 14.Choose BTS node 15.Choose All IP Controlled Board 16.Choose Board Type Selection 17.Choose 3 modules (CHM0, DSM, TRX) and activate CPU version 18.Reset board normally CCM master 19.Choose Active version 20.Choose BTS Node 21.Choose All IP Control board 22.Choose activate version 23.Reset board normally CCM master 24.Reset board normally RMM, CHM0, DSM0 25.Choose Query Version 26.Choose Query Running Information 27.Choose 5 modules (CCM, RMM, DSM, TRX, CHM) 28.Choose Deliver Version 29.Choose MCU 30.Choose 7 modules (SAM0, GCM, RIM0, SAM1, RFE_A, PIM, DPA) 31.Choose Query Version Debugging AN-AAA 1.Fill in IP address computer IP address : 192. 168. 200. 110 Subnet mask : 255.255.255.0 2.Choose SQL Server Enterprise Manager Security and make sure that at authentication is SQL Server and Windows 3.Choose Login General Fill in Name : aaa Choose : SQL Server Authentication and fill in password : aaa 4.Choose Login Server roles System administrators 5.Choose Login Database Access pubs 6.Install radius-winE\DISK1\setup.exe 7.At Database option Fill in SQL Server Name : MACHINENAME Fill in Database name : RasA100 Fill in user name, user password, repeat password : aaa 8.At Version option Fill in Server Run Mode : 2-AN-AAA Only Fill in SNMP Manager IP, DNS Server IP, Wap Gate Ip, PPS address : 1.1.1.1 9.install-config\install.bat 10.At Select Setup Module, choose Configuration module, DBIO module, agent module 11.At Set Module Information Fill in area code : 21 Fill in post code : 200 Fill in local module : 129 12.Change IP address computer IP address : 192. 168. 200. 129 Subnet mask : 255.255.255.0 13.At Set Module Information Fill in Remote module code : 201 Fill in Remote module IP address : 192.168.200.201 14.At Set Database Information Fill in Database server IP or name : 192.168.200.129 Fill in Database : RasA100 Fill in User name and password : aaa Fill in Database type : MS SQL Server 15. Install ZXPDSS-A100 Radius Configure Debugging AN-AAA 16.At Radius Configure database connection Fill in Database server name : MACHINENAME Fill in Database driver : MSSQL Fill in Database name : RasA100 Fill in Database account and password : aaa 17.At Radius Configure Login Fill in operator code and operator password : admin 18.At security association Fill in ip address : 192.168.200.129 Fill in Type : Radius Fill in Secret Key : 1234567890ABCDEF Fill in name : AN-AAA 19.At Manufacture ID setting Fill in Manufacture ID and setting : zte 20.At new IMSI Fill in IMSI : 510030303030303 Fill in MDN : 627218100100 Fill in User name : EVDO 21.At New NAI user Fill in NAI user name : 0303030303 Fill in password & confirm password :
MODIFY IMSI at KYOCERA 1.Press 111111 2.Choose programming 3.Press 000000 4.Choose ESN (cant change) 5.Choose Basic NAM1 5a.Choose phone number (8600000000) 5b.Choose NAM1 Home SID (10817) 5c.Fill in NAM1 Name : Starone 6.Choose Extra NAM1 Info 6a.Choose Country Code : 510 6b.Choose NMSID : 038600000000 6c.Choose true IMSI : 510038600000000 6d.Choose CDMA NAM1 6d1.Choose Directory # : 8600000000 6d2.Choose SID/NID : 01=10817 / 65535 6d3.Choose Primary CHA : 201 6d4.Choose Secondary CHA : 283 6d5.Choose Primary CHB : 384 6d6.Choose Secondary CHB : 777 6d7.Choose Home Sys Reg : No 6d8.Choose Forn SID Reg : No 6d9.Choose Forn NID Reg : No 7.Choose Slot Cycle Index : 2 Telnet ABPM Must put ip address same segment like ABPM at advanced Then telnet ip ABPM Login : ZTE Password : ZTE MNIC_J> ldm_print_all Performance Management 1.Views Performance Management Statistics 2.BSS Global Voice Call Statistics Execute Statistics BSS Global Voice Call Sum BSS Global Voice call Success Number BSS Global Voice Call Success Rate ( % ) Markov Call From the phone : 1.System Tools Network Performance Test 2.NPT 3G BSS 3.97DTest Call Enable 1/2 rate From the system : 3.97DTest Manual Call Service type : M_SO_Markov3 ( BSC Call ) 4.Fwd RC : 3 5.Add IMSI 4.97DTest Call Set Service type : Markov3 Result Know how to debug BSC, but still need support from the expert if there is any problem Know how to inform to the expert if there is any problem during debugging or configuring BSC Have knowledge about BSC, but still need to learn Can work together with expert, local engineer and Indosat engineer during built STARONE system Problems Encountered Lack of training Need to learn more about BSC (debug and configure) Cant understand all of document in spesific Need another project for more knowledge Future Plan Keep on learning on ZTE CDMA 2000 1x Network System, background and foreground, and also debugging BSC Learn another equipment. Not only BSC, but MGW, MSCe and HLRe also Always keep good relationship with other ZTE engineers, local & Chinesse engineers and Indosat engineers