Professional Documents
Culture Documents
User manual
Part NO
Parts
HUD
OBD Cable
Velcro
Sensor
Lock nut
Spanner
Guide
1
1
2
4
4
2
1
2. Installation
2.1 The OBD socket of vehicle was usually located under
dashboard, please find it out and plug OBD cable of HUD.
2.2 Connect the other terminal(mini USB) of OBD cable to
HUD.
2.3 Place HUD on top, left side of dashboard, and adjust its
position for driver can easy read the reflection of HUD
display on windshield.
2.4 Stick catoptrics film at the position of HUD reflection
image on windshield to make the HUD reflection image
clear.
2.5 Turn on power ( ACC ON),no need start engine.
2.5.1 HUD starts to learn protocol & make connection with
ECU. Also can use Manual Select PROTOCOL Mode
(MSPM) to learning, please refer to section 4.18.
4.Operation
4.1 Basic function display: pressing Function Key, can sequent select HUD display function form: Vehicle Speed,
Engine RPM, Fuel Consumption Rate, Throttle Position
Ratio, Engine Coolant Temperature, Battery Voltage, and
Limit Speed Setting,etc in rotation.
4.2 Vehicle Speed Display
lit,
shows current
vehicle speed (Km/h or Mile/h ).
4.3 Engine Revolutions Per Minute Display
lit
shows current Engine revolutions per minute
(RPM/10).
4.4 Fuel Consumption Rate:
lit,
shows fuel
consumption rate in KMs per liter.
4.5 Throttle Position Ratio Display
lit,
shows
throttle position ratio ( 0~100%).
4.6 Engine Coolant Temperature Display
lit,
.
4.15 Preset tire pressure threshold:
lit then press
Setting key into High Pressure adjust mode, use Function Key to adjust threshold. Range is from 40 to 60 PSI.
4.16 Preset tire pressure threshold:
lit then press
Setting key into Low Pressure adjust mode, use Function
Key to adjust threshold. Range is from 25 to 45 PSI.
4.17 TPMS Sensor learning mode:
refer to sensor
user guide.
4.18 Manual Select Protocol Mode (MSPM):
4.18.1 Power on HUD, press Function Key over 5 times then
press Setting Key to enter MSPM
4.18.2 The display show Cxx, C means that you can use
Function Key to change protocol, xx is protocol number. Press Setting Key to execute the protocol learning.
HUD display rxx, r means that HUD is running the
selected protocol.
4.18.3 Press Function Key to interrupt learning.
4.18.4 HUD will display speed once learning is successful.
4.18.5 Protocol List for EH1000/EHM5000/EHAT5000
NO
1
3
5
7
9
11
13
15
17
19
21
Protocol
TOYOTA
KWP2000 Fast
ISO14230A
CAN(500K,29 bits)
CAN(250K,29Bits)
ISO14230C
KWP2000 SLOW
ISO14230F
PROTON SARVY
Renault CAN
Citroen
NO
2
4
6
8
10
12
14
16
18
20
23
Protocol
Reserved
ISO9141
CAN( 500K,11 Bits)
CAN(250K,11Bits)
NISSAN CAN
ISO14230D
ISO14230E
ISO14230B
TOYOTA Comfort
PROTON GEN2
Hyundai (old)
marked.
5.Electronic specification:
Head Up Display
Working voltage
Working
current
9~30 V DC
80 mA
Operating temperature
-30 C to 85C
Circuit protection
Speed Indication
0 ~ 400 KM/HR
Frequency
433.92 MHz
3.
Sensor Installation
When the wheel lit RED and Bi sound, it mean the sensor ID is saved.
STEP 1: Left Front
3. Fix film and scratch water off. Wait for dry one minute
3.3.3 Screw (1) lock nut back and using (3) Wrenches to lock
tight. This prevents sensor from easy removing also in
favor of sensor stationary. Note: User may ignore this
fixture, when causing inflation hassle concerns.
3.3.4 Continue to install all other sensors with the same procedure. .
Note
NOTE: if you do not remove the cuticle, the reflective image will be
vague.