Professional Documents
Culture Documents
DFTG 2040 Fall 2013 PDF
DFTG 2040 Fall 2013 PDF
Assignments
DFTG 2040, Advanced 3D Modeling Mechanical
As a student at Georgia Northwestern Technical College, you are required to maintain a
positive level of work ethics. By practicing work ethics everyday in the classroom, you
are preparing for the skills needed to be a successful employee. Because of these
occupational and work habits, the lab will be treated like a work environment. You will
be evaluated on your demonstration on the following work ethic categories. Each week
you will focus on the given topic as you build habits from the previous week. Weeks 1115 will allow for reflection and practice of all work ethics skills covered in the term.
Week
1
Week
2
Week
3
Week
4
Week
5
Week
6
Week
7
Week
8
Week
9
Week
10
Communication
Cooperation
Respect
Assignments
The assignments listed below must be submitted in a timely
manner. Assignments must be submitted for grading every
week in order to get the necessary feedback from the
Module 2:
1. Reading Assignment: (AutoDesk Inventor 2012: Essentials
Plus) Read Chapter 8 and follow sample exercises.
2. Hybrid Participation Points: See Instructional Videos
link on Resources section of Drafting Webpage.
Module 3:
1. Reading Assignment: (AutoDesk Inventor 2012: Essentials
Plus) Read Chapter 9 and follow sample exercises.
2. Hybrid Participation Points: See Instructional Videos
link on Resources section of Drafting Webpage.
Directions: Watch the videos in the Unit 17 Sketch Blocks
section, the Unit 4 Assembly Management section, the Unit
12 Frame Generator section, the Unit 20 Content Center,
and the Unit 24 Design Accelerators of the Inventor 2011 or
2012 Tutorials. Take the Chapter review quizzes from these
sections as many times as needed to score a minimum of
90%. If you do not watch the videos and only take the
quizzes, then your participation points will reflect that by
being much lower. These videos are required if you are
taking the hybrid version of this course in order to gain
participation points. Participation points make up 15% of the
total average. *If you are enrolled in the traditional section of
this course, then the videos are a great supplement and your
Module 4:
1. Reading Assignment: (Autodesk Inventor 2012 Essentials
Plus) Sheet Metal Design Chapter 10.
2. Hybrid Participation Points: See Instructional Videos
link on Resources section of Drafting Webpage.
Directions: Watch the videos in the Unit 14 Sheet Metal
section of the Inventor 2011 or 2012 Tutorials. Also watch
the videos in the Unit 15 Documenting Sheet Metal section.
Take the Chapter review quiz from these sections as many
times as needed to score a minimum of 90%. If you do not
watch the videos and only take the quizzes, then your
participation points will reflect that by being much lower.
These videos are required if you are taking the hybrid
version of this course in order to gain participation points.
Participation points make up 15% of the total average. *If
you are enrolled in the traditional section of this course, then
the videos are a great supplement and your instructor will
decide if they are required or not for your participation grade.
3. Lab Application No. 4a: Complete exercises 10-1, 102, 10-3, 10-4, 10-5, 10-6 and 10-7 in the chapter. Show
instructor completed exercises when finished.
4. Lab Application No. 4b: Complete the project exercise
at the end of the chapter. Show instructor completed
exercise when finished.
Module 5:
1. Hybrid Participation Points: See Instructional Videos
link on Resources section of Drafting Webpage.
Directions: Watch the videos in the Unit 5 Presentations
section of the Inventor 2011 or 2012 Tutorials. Also watch
the videos in the Unit 16 Plastic Part Design section. Take
the Chapter review quiz from these sections as many times
as needed to score a minimum of 90%. If you do not watch
the videos and only take the quizzes, then your participation
points will reflect that by being much lower. These videos are
required if you are taking the hybrid version of this course in
order to gain participation points. Participation points make
up 15% of the total average.
2. Lab Application No. 5: See instructor for lab
application. This lab should provide the opportunity for you to
demonstrate skills covered in the instructional videos.
Exercise files may be obtained from instructor.
3. Work Ethics Cooperation Test: Angel Test
Module 6:
1. Tutorials: There are a plethora of guided tutorials in
Inventor and SolidWorks. See Instructor for tutorial
assignments.
2. Lab Application No. 6: Complete assigned tutorials in
Inventor and show work to instructor when complete.
3. Lab Application No. 7: Complete assigned tutorials in
SolidWorks and show work to instructor when complete.
4. Work Ethics Legal_Ethical Issues Test: Angel Test