Professional Documents
Culture Documents
The company mission is to do and excel the requirement of clients in all Activities
DASH is into. Dash is committed towards excellence in providing services and has
enormous technological and strategic tie ups works wide for conducting all
functions in time
Established in New Jersey, USA in 2000
Active worldwide in more than 27 countries
Our Services
Engineering
Projects
Inspection
Design
Training
Certification
Service is our Success
API 510
Course Content:
Terminology
Overview: API -510, Pressure Vessel Inspection Code.
Introduction
Scope and General Information
Design, Inspection Methods
Deterioration and Failure Modes
Case studies in Pressure Vessel Failures
Periodic Inspection Requirements
Inspection, Repair, Alternation and Reconstruction
Welding Metallurgy : Brittle Fracture
Guide for Inspection of Refinery Equipment, API- 571, 572, 576 & 575
ASME Section V, ASME Section VIII, Div.1
Overview: ASME Section IX
Report Writing
API 653
Major Topics
Introduction
In-depth discussion of:
API Standard 650
API Standard 653
API Document overview:
API RP 575
API RP 651
API RP 652
API RP 571 Items on Effectivity sheet
API RP 577
ASME Documents overview:
Section V, Articles 1,2,6,7 and 23(SE-797)
Section IX ( Welding Qualifications Only)
Other Topics
Welding Metallurgy
Technical Report Writing
Summary
Brittle Fracture
Tank Repair
Construction Problems
Nondestructive Testing
Practice Exam
API 570
Major Topics
Introduction
Piping Technology
In-depth discussion of:
API standard 650
API RP 574
API RP 578
API RP 577
API RP 571- Items on Effectivity Sheet
ASME Document Overview:
Section V, Articles 1, 2, 6, 7, 9, 10 and 23 (SE797 only)
Section IX ( Welding & Brazing Qualifications)
Other Topics
NDT Information
Welding Process
Welding Terminology
Weld Discontinues
Weld Metallurgy
Technical report writing
Summary
Practice Exam
ASME B31.3
ASME B16.5
Class Participants
Students should have some experience at However; participants who do not meet his
requirement are also welcomed to attend this Training to further their knowledge in the
related areas.
Notes
This is an intense course with daily home work and final exam(NDT exam). A study guide is
issued to direct participants pre-class study.
Bring to Class
Students should bring to class: a calculator, a straight edge(or triangle), pencils,
highlighters, lots of questions, and a CAN-DO attitude. Also, participants must bring the
appropriate codes required for the NDT exam.
Perform visual inspection of welds, report on them and assets their compliance with
specified acceptance criteria
Gaining sufficient knowledge to successfully complete the CSWIP 3.0 Visual Welding
Inspector examinations
Practical Examination
DAY3 DAY 4
Day Magnetic powder Fluorescent & Non-Fluorescent
Wet Magnetic powder Fluorescent & Non Fluorescent
Yoke method
Service is our Success
Knowledge of
Prod Method
Coil Method
Head shot Method
Central Conductor Method
Practical Examination
DAY4 and DAY 5
Purpose of the Code
Scope of the Code
Organization of the Code
ASME Sec-V Article-7 & 25
Specification
SD-1186, SE-709
Acceptance Standards
ASME Sec-VIII, Division-1, Appendix-6
Examination : i) General, ii) Specific, iii) Practical
Practical Examination
DAY 2
Practical Examination
DAY 6&7
Radiography Techniques
Exposure Arrangements
Developing
Film handling
Film Interpretation & Evaluation
Specification
SE-94, SE-747, SE-999, SE-1025, SE-1030, SE-1114, SE-1165, SE-1255, SE-1416
Acceptance Standards
ASME Sec-VIII, Division -1, Appendix-4 API5L
Examination: i) General, ii) Specific, iii) Practical
Practical Examination
DAY4
Normal Probes Calibration, DAC Curve & Scanning
DAY5
TR Probes Calibration, DAC Curve & Scanning
DAY6 &7
Angle Probes Calibration, DAC Curve & Scanning
Plotting of Defects
Announces
Open House
Certified Welding Inspector
( CSWIP 3.1 )
Certification/Awarding Body:
Course Objectives:
To understand factors which influence the quality of fusion welds in steels
To recognize characteristics of commonly used welding processes in relation to quality control
To interpret drawing instructions and symbols to ensure that specifications are met
To set up and report on inspection of welds, macro sections and other mechanical tests
To assess and report on welds to acceptance levels
To confirm that incoming material meets stipulated requirements and recognize the effects on weld
quality of departure from specification
To be in a position to pass the Welding Inspector - Level 2 examinations
ENTRY REQUIREMENTS:
Welding Inspector for a minimum of 3 years with experience related to the duties and responsibilities
listed in Clause 1.2.2 of CSWIP document WI-6-92, under qualified supervision, independently verified OR
Certified Visual Welding Inspector (Level 1) for a minimum of 2 years with job responsibilities in the areas
listed in 1.2.1 and 1.2.2 of CSWIP document WI-6-92 OR Welding Instructor or Welding
Foreman/Supervisor for a minimum of 5 years
NEBOSH
About the course
The NEBOSH International General Certificate (IGC) offers comprehensive understanding of
occupational health and safety principles and practices. The program is specifically designed
for managers, supervisors and employee representatives to help manage risks more
effectively. NEBOSH IGC focuses on international standards and management system,
enabling candidates in any industrial sector to efficiently execute work place health and
safety responsibilities.