Test Databank Print
1 Allthings contain imperfections, but is only when they fall outside the level of
acceptance they should be termed?
A. Discontinuity
B. Defect
C. Mechanical damage
D. Welding imperfections
E.
Correct Answer: B
Reference:
Media Type:
Media Location:
Question ID: 10
2 Asingular gas filled cavity that is = or more than 1.6 mm in diameter is termed?
A. Cavity
B. Cluster porosity
C. Blow hole
D. Rounded porosity
E
Correct Answer: c
Reference:
Media Type:
Media Location:
Question ID: 20
3 Lack of fusion imperfections are defined as?
A. Lack of union between two adjacent areas of material
B. Not cleaning out slag
C. Incorrect electrode manipulation in the final run
D. Incorrect set up
E.
Correct Answer: A
Reference:
Media Type:
Media Location:
Question ID: 30
Page 14 What should happen to spatter before visual inspection is carried out?
A. Spatter is not a problem for visual inspection
B. Spatter that is more than 2 mm need not be cleaned for visual inspection
C. Spatter should be cleaned off before visual inspection
D. Spatter will not have any affect on the weld or the base material
E.
Correct Answer: c
Reference:
Media Type:
Media Location:
Question ID: 40
5 Undercut can be defined as one of the following?
A. Concavity in the root of the weld
B. Crater in the fill of the weld
C. An oxide within the weld
D. Depression at the toe of the weld
=
Correct Answer: D
Reference:
Media Type:
Media Location:
Question 1D: 50
6 _ Excess penetration is often caused by which of the following?
A. Too high a welding current
B. Slow travel speed
C. Large root gap
D. All of the above
E.
Correct Answer: D
Reference:
Media Type:
Media Location:
Question ID: 60Page
Mechanical damage can be defined as any surface material caused during?
A. Rolling
B. Casting
C. Forging
D. Using a needle guns to compress weld capping runs
E.
Correct Answer: D
Reference:
Media Type:
Media Location:
Question 1D: 70
When carrying out a Charpy V test a graph can be produced using what as its
base?
‘A. Carbon content
B. Temperature
C. Alloying content
D. None of the above
E.
Correct Answer: B
Reference:
Media Type:
Media Location:
Question 1D: 80
Fully austenitic stainless steels show measurable toughness at ?
A. -270C
B. -300C
Cc. -350C
D. - 400
E
Correct Answer: A
Reference:
Media Type:
Media Location:
Question ID: 9010 The elongation marks on a transverse tensile test are usually how many MM apart?
A. 50MM
B. 10MM
c. 30MM
D. 45MM
E.
Correct Answer: A
Reference:
Media Type:
Media Location:
Question ID: 100
11. Ina Macro assessment table which of the following defect would the inspector look
for?
A. Excess weld metal height
B. Undercut
Cc. Slag
D. All of the above
E.
Correct Answer: D
Reference:
Media Type:
Media Location:
Question ID: 110
12. Afillet weld fracture test is one of the following?
A. Quantitive
B. Qualitative
C. Qualified
D. All of the above
E
Correct Answer: B
Reference:
Media Type:
Media Location:
Question 1D: 12013
14
15
Fillet weld fracture tests are used to assess which welding condition?
A. Leg length
B. Throat size
C. Root fusion
D. Sidewall fusion
EB
Correct Answer: c
Reference:
Media Type:
Media Location:
Question ID: 130
Types of bend test
A. Face
B. Root
C. Side
D. All of the above
E.
Correct Answer: D
Reference:
Media Type:
Media Location:
Question ID: 140
Anick break test is used to assess which type of weld configuration?
A. Double V
B, Fillet weld unequal leg length
C. Fillet weld
D. All of the above
E.
Correct Answer: A
Reference:
Media Type:
Media Location:
Question ID: 15016 Qualitative tests will include which of the following?
A. Macro testing
B. Bend testing
C. Fillet weld fracture testing
D. All of the above
E
Correct Answer: D
Reference:
Media Type:
Media Location:
Question ID: 160
17 Quantitative tests include which of the following?
A. Hardness
B. Toughness
C, Tensile test
D. Alll of the above
E.
Correct Answer: D
Reference:
Media Type:
Media Location:
Question ID: 170
18 Generally the approved Welding Procedure Specification will have which of the
following?
A. Extent of approval
B. Approved in all parameters
C. Parameters play no part in approval
D. Essential variables are not considered when approving a welding procedure
Ss
Correct Answer: A
Reference:
Media Type:
Media Location:
Question 1D: 180
Page 619 The mechanical tests of a welder approval may include which of the following?
A. Bend tests
B. Fillet weld fracture tests
C. Nick break tests
D. All of the above
E.
Correct Answer: D
Reference:
Media Type:
Media Location:
Question ID: 190
20 Awelder approval test is a test of the level of skill attained by the?
A. Pipe fitter/ welder
B. Welder
C. Welders assistant
D. All of the above
E.
Correct Answer: B
Reference:
Media Type:
Media Location:
Question ID: 200
Page