Professional Documents
Culture Documents
ANSYS, Inc. Service Pack R14.5.7 Update
ANSYS, Inc. Service Pack R14.5.7 Update
ANSYS, Inc.
Southpointe
275 Technology Drive
Canonsburg, PA 15317
ansysinfo@ansys.com
http://www.ansys.com
(T) 724-746-3304
(F) 724-514-9494
Release 14.5.7
May 2013
ANSYS, Inc. is
certified to ISO
9001:2008.
Disclaimer Notice
THIS ANSYS SOFTWARE PRODUCT AND PROGRAM DOCUMENTATION INCLUDE TRADE
SECRETS AND ARE CONFIDENTIAL AND PROPRIETARY PRODUCTS OF ANSYS, INC., ITS
SUBSIDIARIES, OR LICENSORS. The software products and documentation are furnished
by ANSYS, Inc., its subsidiaries, or affiliates under a software license agreement that
contains provisions concerning non-disclosure, copying, length and nature of use, compliance with exporting laws, warranties, disclaimers, limitations of liability, and remedies,
and other provisions. The software products and documentation may be used, disclosed,
transferred, or copied only in accordance with the terms and conditions of that software
license agreement.
ANSYS, Inc. is certified to ISO 9001:2008.
Third-Party Software
See the legal information in the product help files for the complete Legal Notice for
ANSYS proprietary software and third-party software. If you are unable to access the
Legal Notice, please contact ANSYS, Inc.
Published in the U.S.A.
Table of Contents
Introduction ............................................................................................................. v
1. Platform, Product & CAD Support ....................................................................... 1
2. Downloads & Prerequisites ................................................................................. 3
3. Installation .......................................................................................................... 5
3.1. Resolved Issues and Limitations .................................................................... 6
3.2. Documentation Corrections .......................................................................... 6
4. Licensing ............................................................................................................. 7
4.1. Resolved Issues and Limitations .................................................................... 7
5. Advisories & Compatibility Limitations .............................................................. 9
6. ANSYS Structural Products ............................................................................... 11
6.1. Mechanical ................................................................................................. 11
6.1.1. Resolved Issues and Limitations .......................................................... 11
6.2. Mechanical APDL ........................................................................................ 13
6.2.1. Resolved Issues and Limitations .......................................................... 13
6.2.2. Documentation Corrections ............................................................... 17
6.3. AUTODYN ................................................................................................... 17
6.3.1. Resolved Issues and Limitations .......................................................... 17
6.4. AQWA ......................................................................................................... 18
6.4.1. Resolved Issues and Limitations .......................................................... 18
6.5. ASAS .......................................................................................................... 18
6.6. BEAMCHECK ............................................................................................... 19
6.7. FATJACK ..................................................................................................... 19
7. ANSYS Fluids Products ...................................................................................... 21
7.1. FLUENT ....................................................................................................... 21
7.1.1. Resolved Issues and Limitations .......................................................... 21
7.1.2. Known Issues and Limitations ............................................................. 24
7.1.3. Documentation Corrections ............................................................... 25
7.2. CFX ............................................................................................................ 25
7.2.1. Resolved Issues and Limitations .......................................................... 25
7.3. TurboGrid ................................................................................................... 27
7.3.1. Resolved Issues and Limitations .......................................................... 27
7.4. BladeModeler ............................................................................................. 28
7.5. CFD-Post .................................................................................................... 28
7.5.1. Resolved Issues and Limitations .......................................................... 28
7.6. Polyflow ..................................................................................................... 28
8. ANSYS Electronics Products .............................................................................. 29
8.1. Icepak ........................................................................................................ 29
8.1.1. Resolved Issues and Limitations .......................................................... 29
9. ANSYS Geometry & Mesh Prep Products .......................................................... 33
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
iii
iv
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
Introduction
The following information is specific to the ANSYS, Inc. Service Pack Release
14.5.7 and serves as an update to the entries published in the ANSYS Inc. Known
Issues and Limitations document for Release 14.5. Within each product section
(beginning with ANSYS Structural Products) are sub-sections:
Resolved Issues and Limitations (since Release 14.5)
Known Issues and Limitations (where applicable, specific to Release 14.5.7)
Documentation Corrections (where applicable)
Also included are corrections to known documentation inaccuracies and omissions. Any inaccuracies found following publication of this document will be
posted in the Documentation section on the customer portal.
The parenthetical numbers associated with each entry are reference numbers
corresponding to an internal bug tracking system. The numbers are included to
help to facilitate ANSYS, Inc. technical support and help to ensure that the issue
described in the entry is resolved.
Additional service packs may become available for some of the entries. See the
ANSYS Customer Portal for information about service packs and any additional
items not included in this document. First-time users of the customer portal must
register via the ANSYS Web site (www.ANSYS.com) to create a password.
Note
In addition to this document, a ReadMe is available with information
specific to:
Download Instructions
Windows Prerequisites
Windows Installation Instructions
Linux Installation Instructions
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
vi
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
Chapter 3: Installation
The following information is relevant to ANSYS Release 14.5.7 and serves as an
update to the entries published in the ANSYS Inc. Known Issues and Limitations
document for Release 14.5.
Important
ANSYS Release 14.5 must first be manually uninstalled before installing Release 14.5.7. Detailed instructions to uninstall the product
are available via the ANSYS Customer Portal at Downloads> Installation
and Licensing Help and Tutorials. In the Installation and Licensing
Basics section of the customer portal page, open the Installation and
Licensing Documentation PDF. Within either the ANSYS, Inc. Installation
Guide for Linux or the ANSYS, Inc. Installation Guide for Windows, see
chapter 6: Uninstalling the Software.
The customer portal is accessible from the ANSYS Website (www.ansys.com).
For a complete listing of the ANSYS products supported on the Windows 8 operating system, see the ANSYS Website> Support> Platform Support: http://www.ansys.com/Support/Platform+Support
If you have any problems installing this program, please contact your IT department.
Windows Installation Instructions
Be aware that Windows 7, 8, and Vista use a feature called User Account Control
(UAC) to control privileges and automatically reduce the potential of security
breaches in the operating system. However, UAC limits your accessibility to system
areas and can cause unpredictable behavior in ANSYS products. Because of this
limitation, we strongly recommend performing the installation with full administrative options.
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
Installation
Recommended Installation:
UAC should be turned off and installation performed with full administrative privileges (using Run as Administrator from the context menu). Please follow your operating system instructions for disabling UAC. Note: Because of UAC changes in
Windows 8, the recommended installation option differs from what is contained
in the ANSYS, Inc. Installation Guide for Windows. Please use the recommended installation procedure contained in this document when installing on Windows 8.
Detailed installation instructions for Windows are available via the ANSYS Customer Portal at Downloads> Installation and Licensing Help and Tutorials. In the
Installation and Licensing Basics section of the customer portal page, open the
Installation and Licensing Documentation PDF. Within ANSYS, Inc. Installation
Guide for Windows, see chapter 2: Platform Details and chapter 4: Installing the
Software.
Except as described in this document, the installation steps contained in the
current ANSYS, Inc. Installation Guide for Windows are the same for Windows 8.
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
Chapter 4: Licensing
The following information is relevant to ANSYS Release 14.5.7 and serves as an
update to the entries published in the ANSYS Inc. Known Issues and Limitations
document for Release 14.5.
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
10
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
11
12
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
Mechanical APDL
material model is selected to be K or R (via Reference Units (Temperature)), it is
interpreted in the solver as having units of C or F, has been included in this
Service Pack. (50522)
The correction for the error described in Class3 Error Report WB201306, specific
to Rigid Dynamics where in some situations results given by joint probes for
universal joints are incorrect, has been included in this Service Pack. (51301)
The correction for the error described in Class3 Error Report WB201307, where
results might be displayed in the wrong unit system when a user defined result
is scoped to a surface or to a path (includes the identifier from a regular result
in the expression detail), has been included in this Service Pack. (52206)
Specific to the Rigid Body Dynamics solver, the behavior of frictional contact has
been improved to ensure correct results with the RBD solver. (53842)
13
14
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
Mechanical APDL
The stress results from SHELL281 elements with KEYOPT(1) = 2 were not properly
calculated in a coordinate system other than the element coordinate system.
This behavior has been fixed. (50027)
Buckling analysis using the subspace iteration method (BUCOPT,SUBSP) and
modal analysis using the unsymmetric or damped methods (MODOPT,UNSYM
or MODOPT,DAMP) have been improved when the solver runs in out-of-core (or
partially out-of-core) mode. Prior this correction, the analysis could stop or hang
when the scratch (disk) space became full and that disk space was not allocated
in the current working directory. (50054)
The correction for the error described in Class3 Error Report 201301, regarding
a scenario where the thermal-electric contact (modeled through CONTA171,
CONTA172, CONTA173, CONTA174, CONTA175 with KEYOPT(1)=3 or 4) conducts
electric current and heat when the contact is open, has been included in this
Service Pack. (50196)
The correction for the error described in Class3 Error Report 201304, regarding
a scenario where stress results from /POST1 load case operations (LCOPER) involving any load case files (LCWRITE) will be incorrect for any 3-D shell elements
(SHELL63, SHELL181, SHELL281, or SOLSH190), 2-D axisymmetric shells (SHELL208
or SHELL209), or 3-D layered solid elements (SOLID185 or SOLID186) under specific conditions, has been included in this Service Pack. (50235)
Brake squeal analyses using node-to-surface contact elements (CONAT175) in
conjunction with a ramped friction coefficient now work as expected. This correction prevents the analysis from encountering a segmentation error. (50284)
A correction was made to the RESP command for acceleration input and absolute
acceleration spectrum output. Previously, the averaging of the acceleration was
incorrect, which could lead to incorrect spectrum values at low frequencies.
(50405)
When using Distributed ANSYS, the sparse solver would occasionally report error
messages involving error code 19. This has been corrected. (50705)
A correction was made to eliminate program aborts caused by the IC command
and the ICCG solver being used in the same simulation. (50910)
The CBDOF command can now be used when .RST and .DB files do not exist or
are not consistent. This behavior is consistent with version 12.1 and older. (51035)
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
15
16
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
AUTODYN
For shape memory alloy material model (TB,SMA), equivalent transformation
strain as a ratio of maximum transformation strain is now available as an output
variable of nonlinear record (NL:EPEQ) for the memory effect option (MEFF). It
was previously only available for the superelasticity option (SUPE). (54156)
Linear perturbation modal analyses that employ the userinter.F subroutine to
include user-defined contact interactions now work as expected. This correction
prevents the analysis from encountering a warning about element result items
having the value INFINITY. (54165)
The correction for the error described in Class3 Error Report 201307, regarding
incorrect reduced mass matrices (and possibly reduced damping matrices) when
performing a substructure generation pass with the sparse solver, has been included in this Service Pack. (54526)
The problem of the Jobname.MODE file from a modal analysis being corrupted
when the model contains superelements and a subsequent mode superposition
PSD analysis is performed has been corrected. (55164)
6.3. AUTODYN
The following information is relevant to ANSYS Release 14.5.7 and serves as an
update to the entries published in the ANSYS Inc. Known Issues and Limitations
document for Release 14.5.
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
17
6.4. AQWA
The following information is relevant to ANSYS Release 14.5.7 and serves as an
update to the entries published in the ANSYS Inc. Known Issues and Limitations
document for Release 14.5.
6.5. ASAS
No corrected issues, limitations, or documentation inaccuracies.
18
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
FATJACK
6.6. BEAMCHECK
No corrected issues, limitations, or documentation inaccuracies.
6.7. FATJACK
No corrected issues, limitations, or documentation inaccuracies.
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
19
20
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
21
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
FLUENT
A bug that could cause a crash if a Custom Field Function using pollutant
quantities is activated while pollutant equations are not being solved has been
fixed. (49103)
Specific to using solver license keys (non-HPC keys) in parallel, the number of
Fluent licenses checked out is now equal to the number of parallel processes
being run. (49288)
Automatic export of RadTherm data in GUI now functions as expected. (49695)
A bug that could cause a crash when using single-species NIST real-gas-model
with mass-flow boundary condition and pressure-based solver has been fixed.
(49870)
A bug in reading data files from when running in batch mode from Icepak has
been fixed. (49901)
A bug that could give incorrect velocity gradients when the node-based gradient
method is used with non-conformal periodic zones has been fixed. (49955)
A bug which could cause Fluent to crash when using the Eulerian Wall Film
model with the phase-change model and shell-conduction has been fixed. (50594)
Using the PEM Fuel Cell model with periodic boundaries now works as expected.
(51033)
A bug causing a crash in the species transport model when reaction in some cell
zones is disabled has been fixed. (51110)
A bug that could prevent the Fluent process from ending when the File|Exit
command is issued in Windows XP has been fixed. (51442)
The capability to use Postprocess Pollutants in Transient Runs is now available
through the Text Command Interface (TUI). (51456)
A bug that consistently caused a crash when using the Lagrangian wall film
model in combination with Node-Based Averaging and DPM Mean Values has
been fixed. (51542)
A bug that causes an error when using non/partially-premixed combustion
model with the real-gas model in transient simulation has been fixed. (51593)
A bug with Node-Based Averaging when used in the Dense Discrete Phase
Model with heat transfer has been fixed. (51709)
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
23
24
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
CFX
7.2. CFX
The following information is relevant to ANSYS Release 14.5.7 and serves as an
update to the entries published in the ANSYS Inc. Known Issues and Limitations
document for Release 14.5.
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
25
26
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
TurboGrid
The functionality for exporting particle track data, when the Laplace number,
Ohnesorge number, Weber number, particle position or particle velocity are included, now operates as expected. (50616, 50617, 50618)
An error preventing the user from typing in the number of partitions for a parallel
run defined in the Solver Manager has been corrected. (50647)
The convergence rate of simulations carried out in parallel has been improved,
by improving communication in the linear solver at partition boundaries. (52327)
A memory error when restarting transient blade row cases with a duration set
to 1 period has been corrected. (52624)
The correction for the error described in Class3 Error Report CFX201305, where
incorrect answers are obtained if the CFX Solver functionality for monitoring
expressions is used to monitor a particle mass flow rate at a boundary, has been
included in this Service Pack. (52970)
The correction for the error described in Class3 Error Report CFX201307, where
the \\% Imbalance reported in the CFX-Solver out file is erroneously based on
global imbalance values when the expert parameter imbalance normalization
type is set to 1 for multi-domain cases, has been included in this Service Pack.
(53051)
The functionality for setting the number rate of particles in a particle user Fortran
routine, while setting a discrete diameter distribution in the user interface, at a
particle injection routine now works as intended. (53671)
The CFX Solver now stops if a distributed parallel run tries to use different versions
on different machines. However, this behavior is only if the maintenance release
is being used for the master process; if the master process is from the standard
14.5 release or earlier, the run may continue but will probably crash. (54368)
7.3. TurboGrid
The following information is relevant to ANSYS Release 14.5.7 and serves as an
update to the entries published in the ANSYS Inc. Known Issues and Limitations
document for Release 14.5.
27
7.4. BladeModeler
No corrected issues, limitations, or documentation inaccuracies.
7.5. CFD-Post
The following information is relevant to ANSYS Release 14.5.7 and serves as an
update to the entries published in the ANSYS Inc. Known Issues and Limitations
document for Release 14.5.
7.6. Polyflow
No known issues, limitations, or documentation inaccuracies.
28
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
29
30
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
Icepak
Import of TCB files is now backwards compatible to read in new formats changed
in release 15 and old formats. (52673)
An issue affecting the Parametric trail has been resolved. (53866)
Assigned die power for package objects not being considered in simulation
leading to lower temperatures. (55576)
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
31
32
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
33
9.2. DesignModeler
The following information is relevant to ANSYS Release 14.5.7 and serves as an
update to the entries published in the ANSYS Inc. Known Issues and Limitations
document for Release 14.5.
34
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
Meshing
Fixed an issue related to a crash associated with deselecting a DesignModeler
parameter. (48635)
Fixed a crash that occurs during active CAD attach when there is no active CAD.
(50454)
During load of a DesignModeler database, the error of Collection was modified;
enumeration operation may not execute. was occurring; this is now fixed. (51242)
A fix was found to prevent DesignModeler from crashing when attempting to
open it on some Red Hat Enterprise Linux 5.9 systems. (51754)
An error for file names containing illegal characters is fixed. (52747)
An issue related with Shaft geometry transferring to Mechanical as a winding
body is fixed. (52569)
A crash during resuming a corrupt database in DesignModeler is fixed. Now it
returns an error for a corrupt database. (52933)
A crash during the transfer of a model containing points on instanced parts is
fixed. (52974)
9.3. Meshing
The following information is relevant to ANSYS Release 14.5.7 and serves as an
update to the entries published in the ANSYS Inc. Known Issues and Limitations
document for Release 14.5.
35
9.4. IC Engine
No corrected issues, limitations, or documentation inaccuracies.
9.6. FLUENT-Meshing
The following information is relevant to ANSYS Release 14.5.7 and serves as an
update to the entries published in the ANSYS Inc. Known Issues and Limitations
document for Release 14.5.
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
FLUENT-Meshing
Non-manifold node(s) on adjacent zones and which are not impacted by re-triangulation will no longer cause prism extrusion to stop. (48533)
Robustness improvements when using switch-to-solution-mode from within a
journal. (48563)
A 32-bit limit on certain mesh IDs which caused errors when reading large grid
files, has been lifted. (49873)
After generating prism layers, the mesh file may be saved using the text command
interface. (50532)
When extruding prisms in small gaps, excessive shrinking is now mitigated.
(50664)
Parsing of the argument list for the auto-mesh text command has been made
more robust. (50827)
Writing the mesh following a Gap Removal - Node Merge sequence on feature
nodes no longer fails. (50866)
When using Auto Identify Topology, Automesh will correctly separate prism base
zones and periodic zones. (50965)
Following a Post Ignore operation to remove bad cells from a mesh, Creating
non-conformal interfaces no longer causes a segmentation violation. (51271)
Switching from Meshing Mode to Solution Mode when the Pre/Post option has
been enabled now works as expected. (51273)
The Faceted Stitch operation leaves unchanged a model with no free edges.
(51316)
Running Post-Ignore operation in batch mode is able to remove prism cells based
on quality measure. (51323)
Zones created interactively are automatically added to lists visible in GUI panels.
(52049)
Re-triangulation and edge loop processes no longer cause problems with nonconformal interface creation. (53707)
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
37
38
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
39
40
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
EKM
10.2. EKM
The following information is relevant to ANSYS Release 14.5.7 and serves as an
update to the entries published in the ANSYS Inc. Known Issues and Limitations
document for Release 14.5.
Note that the EKM upgrade requires changes to the EKM server. Detailed instructions are available on the ANSYS Customer Portal at Knowledge Resources>
Online Documentation> Simulation Process & Data Management> EKM Upgrade
Guide. The customer portal is accessible from the ANSYS Website (www.ansys.com).
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
41
10.3. DesignXplorer
The following information is relevant to ANSYS Release 14.5.7 and serves as an
update to the entries published in the ANSYS Inc. Known Issues and Limitations
document for Release 14.5.
42
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.
43
44
Release 14.5.7 - SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS,
Inc. and its subsidiaries and affiliates.