Customer: ALPS EUROPE DISTRIBUTION No. 27207-1040
Date: Jun. 07, 2007
Attention.
RK27112A0A0X
SPECIFICATIONS
ALPS';
MODEL: RK27112A0A0X
( 250kA X2 )
Spec. No.:
Sample No: F4262065M
RECEIPT STATUS
RECEIVED
By Date
Signature
Name
Title
Dsc'D iS Abe
ALPS. _
ALPS ELECTRIC CO.,LTD. appv 0S. Sato
ENG. DEPT. DIVISION
Sales
Head Office
4-7, Yukigaya-otsuka-cho, Ota-ku, Tokyo, 148-8501 Japan
Phone, +81 (3)3726-1211 86523
a1003#03A (EA)No. K272007-1040
SPECIFICATIONS
1, THIS SPECIFICATIONS APPLY TO RK27112A0AOX POTENTIOMETER.
2. CONTENTS OF THIS SPECIFICATIONS.
F4262065M_
K272A000F
3, MARKING
+ MARKING ON ALL UNITS
EIA DATE CODE, RESIST. VALUE, TAPER
4. REMARKS
+ FURNUSH PACKAGE
NUT: 1 WASHER: 1
+ CAUTION
There is a possibility that might be affected by contact resistance of resistive element and wiper in case
of Low impedance of output side in voltage regulation circuit,
For this reason, we require that you adjust to impedance of output side more than 100 tines of total
resistance.
Regardless of the suggested applications of these products being introduced in the specifications,
‘shen using them for equipment and devices requiring a high degree of safety, respective manufacturers
ill please preserve safety of the planned equipment and devices by providing necessary protect ve
cireuits and redundancy circuits and reconfirm if safety is being duly preserved.
Products being introduced in the specifications have been designed and manufactured for applications
to ordinary electronic equipaent and devices such as the AV equipaent, electric hone appliances,
office machines and communications equipment. Consequently, when employing these products for
applications requiring @ high degree of safety and reliability such as the medical equipaent,
aviation and aireraft equipzent, space equipaent and burglar alarm equipaent, the using manufacturers
vill please thoroughly study the proprieties of these products for the planned appl ications,
Although we are exerting our best efforts to maintain the quality of these products, we cannot guarantee
thet they will never cause short circuiting and open circuitry.
Therefore, shen designing an equipment or device with which the priority is given to the safety,
you will please carefully study the influences to the whole equipaent of a single function failure of
Potentiometers and Encoders in advance to make out a fail-safe design providing,SPECIFICATIONS
ELECTRICAL
1. Total resistance 250k0(nominal) + 20%
2. Rated voltage
The rated voltage shall be the voltage of A.C. (commercial frea~
ency. effective value)
Maximum working voltage : 30V A.C. (A.C. Use only )
3. Resistance taper
% Hegiaun’attenvet ion level on fUli c.c.¥. position : 10008 ain,
5. Insertion loss on full C.¥. position : 0.148 max.
6. Silding noise Less than a7mv ( Measured by JIS C 6443, )
(Neglected a Impulsive noise at the c.w. and
c.c.¥. ends of position)
7. Insuration resistance : more than toowa at Sov 0.c
B. Withstand voltage S00V A.C. for 4 minute.
8. Gang error 308 max.” at -70d8 less than -60da
28 max. at -60d8 less than oda
MECHANICAL ce
4. Total rotational angie : 300° + 3 7
2) Rotational torque 8s35mN-n ( Rotational speed : 60°/sec )
3. Stopper strength No damage with an application of 0. N-n,
4. Resistance to soldering neat
Atter soldering ( Less than 3500 and within Ssec ). there shall be no
evidence of poor contact between resistance element and terminal. or any
physical damages as a result of the test
5. Bushing nut tightening strength : Tightening toraue a
to be no greater than 1, 5N-m aay
Pay attention to tighten as shown right —-
Otherwise. the strength may not be assured. FE Jia
6. Push / pull’ strength
No damages with an application of push or pull force 100N for £0 sec.
ENDURANCE
4, Rotational life 15,000 cyctes min.
NOTE
4. The Items except above mentioned items sheil meet or exceed JIS C 6443
2. This type Is protected against sulfides.
€@ ALPS ELECTRIC CO., LTD.
apeo.fowxo. osep. [rite
F4262065M
or 22,96 | ov, 22.96 | or. 22°98
DOCUMENT 0.
Y, voshiota |. Satoh | k Saitoh
swe [pare [neo [enxo [osee
[Ese] Ret|
aa ALPS ELECTRIC CO.,LTD
1-7 YUKIGAYA OTSUKA-CHO OTA-KU TOKYO JAPAN
(%)
100
90
710
X100% —
60
50
40
INPUT VOLTAGE
41-2 OUTPUT VOLTAGE
1-3
30
TERM
TERM.
20
10
ae
0 30 60 90 120 150 180 210 240 270 300°
TERM. 1 — C.W. ROTATION ANGLE ——> TERM. 3
FULL C.C.W. POSITION
AT 180° C.W. SHAFT ROTATION FROM FULL C.C.W. POSITION VOLTAGE
PERCENT SHALL FALL WITHIN THE LIMITS OF 15-30 PERCENT
wero. [enxo, /]osao. [wane
Mn 156 lav 16. Se| RESISTANCE TAPER ( A_)
5. Sasatl \-. Zvounan | °C Ne.
Syma | OATE [APPO [GuxD [Osa F4262065M
a a A25.341 20
10
x Wt *
0. 5X45* CHAM -3| lo | 2 Sy
Ra" Ra . r
25
12 140 <
Maxo. 75
Y
RARIZE FB£10.1
(HAMS RRB) eaee ee
P.W.B. MOUNTING DETAIL
TOLERANCE. £ 23.23
VIEWED FROM MOUNTING SIDE
ata
10) (940.3 WoUNTING SURFACE
R27 Rt
1 4
EST BAO KBE
cts mes writ
uso feos
40 <1
HOSIRP.W. BOLHR Bhetbes ores,
aauran,
Cautlon for soldering
Please avoid soldering on upper surface of P.W.B. as shown
ay
Che Terninal
Solder
Bhe
solder ro
4% ALPS ELECTRIC CO., LTD.
een. Jewxo. oso. |riru
a
dor, 14,83 | Aor 44°89 | Aor. 14°99 F4262065M
5. Aizawa | M, Saton | ¥, Saitan
supers