Professional Documents
Culture Documents
st21 PDF
st21 PDF
Item*
1
Formwork
1a
Formwork dimensions
and openings for
services
1b
1c
Condition of formwork,
props & bracing
Reinforcement
(cast in-situ & Precast)
2a
Standards
1)
2)
3)
1)
2)
3)
4)
1)
2)
3)
4)
1)
2)
Page 19
Appendix 1a
Item*
Standards
2b
1)
2c
Cover provision
1)
2d
1)
2)
1)
2)
1)
2)
Tolerance for opening: +10 for size and 25mm for location
3)
4)
5)
2e
Rebar Condition
Finished Concrete
(cast in-situ & Precast)
3a
Page 20
Appendix 1a
Item*
3b
3c
Exposed surface
Precast Specific
Requirements
4a
Lifting points/inserts
4b
Sleeve
system/connections
Standards
6)
7)
1)
2)
3)
4)
5)
1)
2)
3)
4)
5)
No cracks or damages
1)
2)
1)
2)
3)
4)
Page 21
Appendix 1a
Item*
4c
4d
Interface/joint
requirements
Cast-in steel
items/welded & bolted
connections
Standards
1)
Joint taper:
Over 3m length: 6mm
Maximum for entire length: 9mm
2)
3)
4)
5)
1)
2)
3)
Structure Quality
5a
1)
5b
Reinforcement (Rebar)
1)
2)
3)
Page 22
Appendix 1a
Item*
Standards
Non-destructive testing
6a
6b
Electro-Covermeter test
for concrete cover
1)
2)
3)
4)
1)
2)
3)
For each reading, full point for 5mm and half point for
>5mm to 8mm. For each location, no point will be
awarded if any of the 4 readings exceeds 12mm.
4)
For the assessment of concrete cube test results, the percentage of points shall be awarded based
on the percentage of non-compliance as tabulated in the table below :
Percentage of Points awarded
Percentage of non-compliance
100%
0 - 2.5%
75%
2.6 - 5.0%
50%
5.1 - 7.5%
25%
7.6 - 10%
0%
> 10%
* An item is deemed to have failed if any one of the standards is not met.
Page 23
Appendix 1b
Item*
1
Main member/Partial
assembled component
1a
Physical dimensions
1b
1c
1d
Welding
Bolting
Standards
1)
2)
3)
1)
2)
3)
1)
Weld size, length and profile shall meet the structural steel
specifications and drawings
2)
3)
4)
1)
2)
3)
4)
Page 24
Appendix 1b
Item*
Metal decking
2a
2b
Shear studs
Standards
5)
6)
1)
2)
3)
4)
5)
6)
1)
2)
3)
4)
1)
2c
Erection tolerances
3a
Column verticality
1)
3b
Column position
1)
3c
Beam level
1)
Page 25
Appendix 1b
Item*
Standards
2)
1)
3d
Beam position
4a
Thickness of coating
1)
4b
Condition
1)
No visible damages
2)
1)
2)
# For test records, the following table would be used to determine the points awarded:
Points awarded
20
0%
15
0%<x5%
10
5%<x10%
10%<x15%
x>15%
Page 26
Appendix 1c
Item*
1
Standards
1)
2)
Installation of sheathing
Debonding
1)
2)
3)
4)
1)
2)
3)
1)
2)
3)
* An item is deemed to have failed if any one of the standards is not met.
Page 27