Professional Documents
Culture Documents
JN0-360 Actualtests Premium Exam 322q PDF
JN0-360 Actualtests Premium Exam 322q PDF
QUESTION NO: 1
Which two statements are true about MPLS VPNs? (Choose two.)
A. With Layer 3 VPNs, the providers routers participate in the customers Layer 3 routing.
B. MPLS VPNs are designed to run over private networks rather than the public Internet.
C. With Layer 2 VPNs, the provider does not participate in the routing of the customers private IP
traffic.
D. MPLS VPN tunnels are always encrypted.
Answer: A,C
Explanation:
QUESTION NO: 2
A. inject
B. pop
C. push
D. swap
Answer: D
Explanation: http://www.juniper.net/techpubs/software/junos-security/junos-security96/junos-
security-swconfig-interfaces-and-routing/mpls-ov.html
QUESTION NO: 3
A. T Series devices
B. SRX Series devices
C. MX Series devices
D. MAG Series devices
Answer: B
Explanation: http://www.juniper.net/techpubs/en_US/junos10.0/information-products/pathway-
QUESTION NO: 4
Answer: D
Explanation:
QUESTION NO: 5
For a network running single-area OSPF, how would you decrease the size of the link-state
database (LSDB)?
Answer: D
Explanation:
QUESTION NO: 6
A. IP addresses that are reserved for use only with MPLS VPNs.
B. IP addresses that are never installed in the routing table.
C. IP addresses that are reserved for use only with GRE tunnels.
D. IP addresses specifically used for out-of-band management.
Answer: B
QUESTION NO: 7
Which statement correctly describes the difference between a generated and an aggregate route?
Answer: B
Explanation:
QUESTION NO: 8
A. All IPv4 routes in the master routing instance are shared with user-defined routing instances.
B. Interface routes in the master routing instance are shared with user-defined routing instances.
C. Routes in the master routing instance are not shared with user-defined routing instances.
D. All routes in the master routing instance are shared with user-defined routing instances.
Answer: C
Explanation:
QUESTION NO: 9
Which routing table contains the route information for the user-defined routing instance called
Candidate1?
A. inet.Candidate1.0
B. Candidate1.inet.0
C. inet.0
D. Candidate1-inet.0
Answer: B
Explanation:
QUESTION NO: 10
Which two routing-instance types are used for non-VPN-related applications? (Choose two.)
A. virtual-router
B. vrf
C. forwarding
D. vpls
Answer: A,C
Explanation:
QUESTION NO: 11
What are two characteristics of load-balancing implementation on a Junos device? (Choose two.)
Answer: B,C
Explanation:
QUESTION NO: 12
A network administrator has been asked to configure the most specific aggregate route to
summarize the four specific prefixes shown below:
10. .5.0/24
10. .12.0/24
10. .17.0/24
10. .21.0/24
A. [edit routing-options]
user@router# show
aggregate {
route 10. .0.0/19;
}
B. [edit routing-options]
user@router# show
aggregate {
route 10. .0.0/20;
}
C. [edit routing-options]
user@router# show
aggregate {
route 10. .0.0/21;
}
D. [edit routing-options]
user@router# show
aggregate {
route 10. .0.0/18;
}
Answer: A
Explanation:
QUESTION NO: 13
A. Unified ISSU is built upon graceful-restart extensions to allow upgrades with no impact to the
data plane.
B. Unified ISSU is supported on systems with single or dual Routing Engines.
C. Unified ISSU permits both upgrades and downgrades with no control plane disruption and is
based on the graceful Routing Engine switchover (GRES) feature.
D. Unified ISSU is based on nonstop-routing (NSR) and graceful Routing Engine switchover
(GRES), and permits software upgrades only.
Answer: D
Explanation:
R0 is a Juniper Networks MX router with dual Routing Engines. You must load new software on
R0 while ensuring no control plane disruption and minimal data loss.
A. graceful restart
B. NSR
C. graceful Routing-Engine switchover (GRES)
D. unified ISSU
E. BFD
Answer: B,C,D
Explanation:
QUESTION NO: 15
What are two ways that nonstop routing works? (Choose two.)
Answer: A,D
Explanation:
QUESTION NO: 16
What are three ways that graceful Routing Engine switchover provides redundancy? (Choose
three.)
Answer: A,B,E
QUESTION NO: 17
Which protocol do multichassis link aggregation group (MC-LAG) devices use to exchange the
control information between two MC-LAG network devices?
Answer: D
Explanation:
QUESTION NO: 18
Which two statements are true about unified ISSU? (Choose two.)
Answer: B,D
Explanation:
QUESTION NO: 19
Answer: C
Explanation:
QUESTION NO: 20
You have a router with dual Routing Engines. You want to ensure that your users experience
minimum downtime. You have decided to enable graceful Routing Engine switchover on the
router.
A. {master}
user@R1-re0> show system snapshot
Information for snapshot on hard-disk
Creation datE. Nov 1 1 :5 :0 2012
JUNOS version on snapshot:
jbase : 11.4R2
jcrypto: 11.4R2
jdocs : 11.4R2
jkernel: 11.4R2
jpfe : M40-11.4R2
jroute : 11.4R2
B. {backup}
user@R1-re1> show system switchover
Graceful switchover: On
Configuration databasE. Ready
kernel databasE. Ready
Peer StatE. steady State
C. {backup}
user@R1-re1> show system snapshot
Information for snapshot on hard-disk
Creation datE. Nov 1 1 :5 :0 2012
JUNOS version on snapshot:
jbase : 11.4R2
jcrypto: 11.4R2
jdocs : 11.4R2
jkernel: 11.4R2
jpfe : M40-11.4R2
jroute : 11.4R2
D. {master}
user@R1-re0> show system switchover
Graceful switchover: On
Configuration databasE. Ready
kernel databasE. Ready
Peer StatE. steady State
QUESTION NO: 21
Which OSPF LSA type is sent from the ABR to describe an ASBR that is in an area to which it is
connected?
A. Type 7
B. Type 5
C. Type 4
D. Type 3
Answer: C
Explanation:
QUESTION NO: 22
A. The BDR advertises link-state information with all other OSPF routers on the segment.
B. The BDR forms an adjacency with all other OSPF routers on the segment.
C. The BDR is ready to assume the role of the DR device if it fails.
D. The BDR functions can be distributed to the DR device on the segment.
Answer: B,C
Explanation:
QUESTION NO: 23
Which OSPF adjacency state is reached when a hello packet has been sent, but bidirectional
communication has not been established?
A. Down
B. Init
C. 2-way
D. ExStart
QUESTION NO: 24
Answer: C
Explanation:
QUESTION NO: 25
A. backbone area
B. not-so-stubby area
C. stub area
D. totally stubby area
Answer: A,B
Explanation:
QUESTION NO: 26
Which LSA packet types are originated only by an OSPF ABR router?
Answer: B
Explanation:
QUESTION NO: 27
In an OSPF environment, which two configuration parameters are used to determine which router
is the DR? (Choose two.)
Answer: A,C
Explanation:
QUESTION NO: 28
You have entered the show ospf route command and see routes with a metric type of EXT2.
Answer: B
Explanation:
QUESTION NO: 29
You want to verify the frequency and type of SPF calculations on your Junos device.
Answer: C
Explanation:
QUESTION NO: 30
You are troubleshooting an OSPF adjacency that is stuck in the ExStart state.
Answer: D
Explanation:
QUESTION NO: 31
A. Create a redistribution policy and apply it as an export policy under the [edit protocols ospf
area] hierarchy.
B. Create a redistribution policy and apply it as an import policy in the [edit protocols ospf]
hierarchy.
C. Create a redistribution policy and apply it as an import or an export policy in the [edit protocols
ospf] hierarchy.
D. Create a redistribution policy and apply it as an export policy in the [edit protocols ospf]
hierarchy.
Answer: D
Explanation:
You are configuring OSPF on a Junos device; however, you have not configured a router ID.
Answer: C
Explanation:
QUESTION NO: 33
Answer: A,C
Explanation:
QUESTION NO: 34
Answer: B
Explanation:
QUESTION NO: 35
Which statement is true regarding the IS-IS designated intermediate system (DIS)?
Answer: A
Explanation:
QUESTION NO: 36
You want to establish an IS-IS Level 1 adjacency between two routers. The adjacency is not
forming.
Which three reasons would account for this issue? (Choose three.)
A. A lack of or a malformed ISO network entity title (NET) on the loopback interface would cause
this issue.
B. The interface MTU might be less than 1492.
C. The IS-IS protocol on the loopback interface has not been enabled.
D. The area IDs might be matched and should be set differently.
E. An ISO NET might not be configured on the physical interface.
Answer: A,B,C
Explanation:
QUESTION NO: 37
Which three statements are true regarding the IS-IS link-state database (LSDB)? (Choose three.)
Answer: A,B,E
Explanation:
QUESTION NO: 38
Which PDU type is sent by an IS-IS router when it detects that its link-state database is out of
date?
A. hello
B. link state
C. complete sequence number
D. partial sequence number
Answer: D
Explanation:
QUESTION NO: 39
What are two similarities between OSPF and IS-IS? (Choose two.)
Answer: A,B
Explanation:
QUESTION NO: 40
Which three statements correctly describe IBGP and EBGP interaction? (Choose three.)
A. IBGP is used within an AS, whereas EBGP is used between two different ASs.
B. EBGP peering is normally loopback-based to provide tolerance for interface or link failures.
Answer: A,C,E
Explanation:
QUESTION NO: 41
Which two statements correctly describe how the AS path attribute is used by BGP? (Choose
two.)
Answer: B,C
Explanation:
QUESTION NO: 42
Which statement describes the role of local preference in the BGP route selection process?
A. Local preference is evaluated early in the BGP route selection process and results in the route
with the highest numerical local preference being selected.
B. Local preference is evaluated early in the BGP route selection process and results in the route
with the lowest numerical local preference being selected.
C. Local preference is used to break ties when all other received BGP attributes are otherwise
equal.
D. Local preference is sent by an EBGP speaker to a neighboring AS in an attempt to influence
how the remote peer's traffic will ingress into your network.
Answer: A
Explanation:
QUESTION NO: 43
Which three BGP attributes are used for loop prevention? (Choose three.)
A. AS path
B. originator ID
C. next hop
D. cluster list
E. origin
Answer: A,B,D
Explanation:
QUESTION NO: 44
You are attempting to influence return traffic into your autonomous system by preferring one router
as an entry point.
Which two BGP attributes will affect this behavior? (Choose two.)
A. originator ID
B. local preference
C. AS path
D. MED
Answer: C,D
Explanation:
QUESTION NO: 45
Which three BGP attributes must be sent to EBGP peers? (Choose three.)
A. local preference
B. atomic aggregator
C. origin
D. next hop
E. AS path
QUESTION NO: 46
A. OpenEstablished
B. OpenConnect
C. OpenConfirm
D. OpenActive
Answer: C
Explanation:
QUESTION NO: 47
Answer: C
Explanation:
QUESTION NO: 48
A route to the same destination is received from two different BGP sources.
A. cluster length
B. AS-path length
C. lowest RID
D. local preference
QUESTION NO: 49
You are troubleshooting a BGP-learned prefix that is not being installed in the routing table.
Answer: C
Explanation:
QUESTION NO: 50
You are asked to configure a new external BGP connection to a peer's loopback interface. You
verify that the peer's loopback interface is reachable, but the BGP connection remains in Idle
state.
A. multipath
B. multihop
C. as-override
D. advertise-inactive
Answer: B
Explanation:
QUESTION NO: 51
Which two statements are true about virtual switches? (Choose two.)
Answer: B,C
Explanation:
QUESTION NO: 52
Answer: A
Explanation:
QUESTION NO: 53
What are three components of the tag portion of an 802.1Q-tagged Ethernet frame? (Choose
three.)
Answer: A,C,D
Explanation:
QUESTION NO: 54
Which three mechanisms are used by switches to build and maintain bridge tables? (Choose
three.)
Answer: A,C,D
Explanation:
QUESTION NO: 55
Answer: A
Explanation:
QUESTION NO: 56
What are two differences between RSTP and VSTP? (Choose two.)
Answer: A,B
Explanation:
QUESTION NO: 57
A rogue switch has been added to your network, exchanged BPDUs, and is now part of the
spanning tree topology.
A. storm control
B. BPDU control
C. root protection
D. loop protection
Answer: B
Explanation:
QUESTION NO: 58
A. 32
B. 64
C. 128
D. 256
Answer: B
Explanation:
QUESTION NO: 59
Which two statements are true about STP and RSTP? (Choose two.)
Answer: B,D
Explanation:
QUESTION NO: 60
What are two types of BPDUs in the Spanning Tree Protocol? (Choose two.)
Answer: A,C
Explanation:
QUESTION NO: 61
You are asked to establish an MPLS LSP between two sites. You are required to ensure the LSP
traverses specific routers within your network.
A. Enable traffic engineering within LDP and define the explicit route the LSP must follow.
B. Implement RSVP and define the explicit route the LSP must follow.
C. Enable traffic engineering within RSVP and define the explicit route the LSP must follow.
D. Implement LDP and define the explicit route the LSP must follow.
Answer: B
Explanation:
QUESTION NO: 62
A. MPLS creates a copy of the mpls.0 table and stores it in the inet.3 routing table.
B. The inet.3 routing table is used by transit routers to identify label values.
C. BGP can use the inet.3 routing table to resolve next hops.
D. MPLS uses the inet.3 routing table to assign labels.
Answer: C
Explanation:
QUESTION NO: 63
Which two statements are correct about default MPLS behavior on Junos devices? (Choose two.)
Answer: A,C
Explanation:
QUESTION NO: 64
Which two statements regarding the MPLS label information base are correct? (Choose two.)
Answer: B,D
Explanation:
QUESTION NO: 65
Which two statements are correct about RSVP path messages? (Choose two.)
Answer: B,C
Explanation:
QUESTION NO: 66
Which two statements are correct regarding LDP-signaled VPLS instances? (Choose two.)
Answer: B,D
Explanation:
QUESTION NO: 67
Which two statements are correct regarding LDP-signaled Layer 2 circuits? (Choose two.)
Answer: B,C
Explanation:
QUESTION NO: 68
Which two statements are correct regarding BGP-signaled Layer 2 VPNs? (Choose two.)
Answer: A,D
Explanation:
QUESTION NO: 69
Which two statements regarding VRF tables are correct? (Choose two.)
A. A PE router's VRF table stores routes received from directly connected CE devices.
B. A PE router's VRF table stores routes received from its IGP from remote PE devices.
C. A PE router's VRF table stores routes received from MP-BGP from remote PE devices.
D. A PE router's VRF table stores routes received from all P and PE devices within the same AS.
QUESTION NO: 70
You have been asked to implement routing policy on the PE devices in your AS and to ensure the
correct customer routes are installed in the appropriate VRF tables.
A. BGP communities
B. VLAN IDs
C. route distinguisher
D. circuit IDs
Answer: A
Explanation:
QUESTION NO: 71
A. The community value is used to identify routes that should be imported by remote PEs.
B. The community value is used to determine valid remote devices when signaling a Layer 3 VPN.
C. The community value is used to identify the source of incoming routes.
D. The community value is used to determine transit devices when signaling a Layer 3 VPN.
Answer: A
Explanation:
QUESTION NO: 72
You have been asked to deploy a Layer 2 VPN for a new customer.
What information will be present in the PE's associated VPN forwarding table? (Choose three.)
Answer: A,C,D
Explanation:
QUESTION NO: 73
You have an established Layer 3 VPN where you are using static routing between your PE and
CE devices. You must advertise their directly connected subnet to remote PE devices.
Answer: B,C
Explanation:
QUESTION NO: 74
You have been asked to verify the state of an LDP-signaled Layer 2 circuit.
Which two commands would you use to verify the state of the connection? (Choose two.)
Answer: B,D
Explanation:
Answer: A,D
Explanation:
QUESTION NO: 76
Which new field is added to the IPv6 header when compared to IPv4?
A. version
B. fragment offset
C. checksum
D. flow label
Answer: D
Explanation:
QUESTION NO: 77
A. multicast header
B. authentication header
C. autoconfiguration options
D. fragment
E. hop-by-hop options
Answer: B,D,E
Explanation:
QUESTION NO: 78
A. DHCPv6 request
B. Layer 2 address of advertising router
C. duplicate address detection notification
D. link MTU
Answer: B,D
Explanation:
QUESTION NO: 79
Which two statements are correct about neighbor discovery in IPv6? (Choose two.)
Answer: B,D
Explanation:
QUESTION NO: 80
You want to configure an interface on your router to use an IPv6 global IP address.
Answer: A,C,D
Explanation:
Which two support tunneling for non-IP protocols on Junos devices? (Choose two.)
A. ATM AAL2
B. GRE
C. IP-IP
D. ATM AAL1
Answer: B,C
Explanation:
QUESTION NO: 82
Which two support the tunneling of IP traffic on Junos devices? (Choose two.)
A. ATM AAL2
B. GRE
C. IP-IP
D. ATM AAL1
Answer: B,C
Explanation:
QUESTION NO: 83
Which two statements are true regarding GRE tunnels? (Choose two.)
Answer: C,D
Explanation:
QUESTION NO: 84
A. If the host sends a packet larger than the MTU, that packet must be dropped.
B. Packets are not dropped because the router clears the DF bit for GRE traffic by default.
C. Packets larger than the MTU are fragmented or dropped depending on the DF bit setting.
D. You can change the tunnel MTU to avoid packet fragmentation or drops.
Answer: C,D
Explanation:
QUESTION NO: 85
-- Exhibit --
StatE.
AgE. 1:03:46
Task: Aggregate
AS path: I
-- Exhibit --
You are advertising the route in the exhibit to your OSPF neighbors.
A. The default route will remain active and will "blackhole" all traffic from your OSPF peers.
B. The default route will become unavailable and will no longer be advertised to your OSPF peers.
C. The default route will remain active and will continue to be advertised to your OSPF peers.
D. The default route will become unavailable and will continue to be advertised to your OSPF
peers.
Answer: B
Explanation:
QUESTION NO: 86
-- Exhibit --
[edit policy-options]
user@router# show
policy-statement load-balance {
from {
then {
load-balance per-packet;
-- Exhibit --
Referring to the exhibit, which configuration correctly applies the load-balancing policy?
A. [edit routing-options]
user@router# show
forwarding-options {
export load-balance;
}
B. [edit routing-options]
user@router# show
static {
export load-balance;
}
C. [edit routing-options]
user@router# show
forwarding-table {
export load-balance;
}
D. [edit routing-options]
user@router# show
routing-table {
export load-balance;
}
Answer: C
Explanation:
QUESTION NO: 87
-- Exhibit --
[edit]
rib-groups {
test {
Referring to the exhibit, what is the result of the RIB group configuration?
A. All routes from the walter.inet.0 and the nancy.inet.0 routing tables will be imported into the
default master routing instance.
B. Routes from the walter.inet.0 routing table will be imported into the nancy.inet.0 routing table.
C. All routes will be shared between the walter.inet.0 and the nancy.inet.0 routing tables.
D. Routes from the nancy.inet.0 routing table will be imported into the walter.inet.0 routing table.
Answer: B
Explanation:
QUESTION NO: 88
-- Exhibit --
{master}[edit]
RE modE. Master
OSPF Complete
RIP Complete
BGP Complete
MPLS Complete
LDP Complete
{master}[edit]
Graceful switchover: On
{backup}[edit]
{backup}[edit]
Synchronization master:
-- Exhibit --
A. An RE switchover is likely to result in BGP disruption, but no dataplane impact will be seen.
B. An RE switchover is likely to result in BGP disruption which will also effect the dataplane.
C. The system is not yet GRES ready, you need to wait for kernel synchronization to complete.
Answer: D
Explanation:
QUESTION NO: 89
-- Exhibit --
{master}[edit]
RE modE. Master
OSPF Complete
RIP Complete
BGP Complete
MPLS Complete
LDP Complete
{master}[edit]
inet.0: 0/0/0/0
inet.2: 0/0/0/0
bgp.l3vpn.0: 0/0/0/0
...
{backup}[edit]
{backup}[edit]
-- Exhibit --
You have been asked to determine if an NSR switchover will be hitless for a given BGP peer.
A. The BGP session is idle on the backup RE indicating that the session will flap at switchover.
B. The task replication process has completed on the master indicating a hitless switchover can
be expected.
C. The GRES synchronization process is underway and must complete before the protocol state
can be checked.
D. The BGP session is idle on the backup RE which is normal; it toggles to established at
mastership change.
Answer: A
Explanation:
QUESTION NO: 90
-- Exhibit --
unit 0 {
family inet {
address 10.100.1.1/24 {
virtual-address 10.200.12.254;
priority 150;
accept-data;
track {
interface ge-1/0/0 {
priority-cost 40;
unit 0 {
family inet {
address 10.100.1.2/24 {
vrrp-group 1 {
virtual-address 10.200.12.254;
accept-data;
-- Exhibit --
Referring to the exhibit, which two statements are correct about the configuration? (Choose two.)
A. R2 is the backup router and will become the master router if ge-1/0/0 on R1 goes down.
B. R2 is the backup router and will remain the backup router if ge-1/0/0 on R1 goes down.
C. If R1 goes down, R2 will become the master and will relinquish mastership once R1 comes
back online.
D. If R1 goes down, R2 will become the master and will remain the master once R1 comes back
online.
Answer: B,C
Explanation:
QUESTION NO: 91
-- Exhibit --
interfaces {
ge-1/0/3 {
unit 0 {
family inet {
address 192.168.1.1/30;
ge-1/1/0 {
unit 0 {
family inet {
address 10.100.10.1/30;
unit 0 {
family inet {
address 10.2.1.13/28;
lo0 {
unit 0 {
family inet {
address 10.100.1.1/32;
address 127.0.0.1/32;
protocols {
ospf {
area 0.0.0.0 {
interface ge-1/0/3.0;
interface ge-1/1/0.0;
-- Exhibit --
A. 192.168.1.1
B. 10.100.1.1
C. 127.0.0.1
D. 10.2.1.13
Answer: B
Explanation:
QUESTION NO: 92
-- Exhibit --
protocols {
isis {
level 1 disable;
interface ge-1/0/0.0 {
level 2 disable;
interface ge-1/1/0.0;
interface lo0.0;
-- Exhibit --
A. Level 1 is enabled.
B. Level 1 is disabled.
C. Level 2 is enabled.
Answer: A
Explanation:
QUESTION NO: 93
-- Exhibit --
[edit]
-- Exhibit --
Referring to the exhibit, which two statements are true regarding the GE interface? (Choose two.)
Answer: A,C
Explanation:
QUESTION NO: 94
-- Exhibit --
user@R2> show
protocols {
export leak;
interface ge-1/1/0.0;
interface ge-1/1/1.0 {
level 1 disable;
interface lo0.0;
policy-options {
policy-statement leak {
term 1 {
from level 1;
to level 2;
then accept;
-- Exhibit --
R1 and R2 have a Level 1 IS-IS adjacency. R2 participates in both Level 1 and Level 2, and is
receiving routes from a Level 2 neighbor. A policy on R2 has been created to leak routes to Level
1, but R1 is not receiving the routes.
Answer: C
Explanation:
QUESTION NO: 95
-- Exhibit --
user@R1> show
interfaces {
ge-1/1/0 {
unit 0 {
family inet {
address 10.100.1.1/30;
family iso;
lo0 {
unit 0 {
family inet {
address 10.100.10.1/32;
family iso {
address 49.1001.0010.0100.00;
isis {
interface ge-1/1/0.0 {
level 2 disable;
interface lo0.0;
user@R2> show
interfaces {
ge-1/1/0 {
unit 0 {
family inet {
address 10.100.1.2/30;
lo0 {
unit 0 {
family inet {
address 10.100.10.2/32;
family iso {
address 49.1001.0010.0200.00;
protocols {
isis {
interface ge-1/1/0.0;
interface lo0.0;
-- Exhibit --
Referring to the exhibit, R1 and R2 are directly connected using interface ge-1/1/0.
A. No adjacency forms
B. Level 2 adjacency forms
C. Level 1 adjacency forms
D. Level 1 and Level 2 adjacencies form
Answer: C
Explanation:
QUESTION NO: 96
-- Exhibit --
user@R1> show
interfaces {
ge-1/1/0 {
unit 0 {
family inet {
family iso;
lo0 {
unit 0 {
family inet {
address 10.100.10.1/32;
family iso {
address 49.1001.0010.0100.00;
protocols {
isis {
level 1 disable;
interface ge-1/1/0.0 {
level 2 disable;
interface lo0.0;
user@R2> show
ge-1/1/0 {
unit 0 {
family inet {
address 10.100.1.2/30;
family iso {
mtu 1496;
lo0 {
unit 0 {
family inet {
address 10.100.10.2/32;
family iso {
address 49.1002.0010.0200.00;
protocols {
isis {
interface ge-1/1/0.0 {
level 2 disable;
-- Exhibit --
Referring to the exhibit, R1 and R2 are directly connected using interface ge-1/1/0.
Answer: B
Explanation:
QUESTION NO: 97
-- Exhibit --
[edit]
...
-- Exhibit --
Answer: B,C
Explanation:
QUESTION NO: 98
-- Exhibit --
Table Tot Paths Act Paths Suppressed History Damp State Pending
inet.0
0 0 0 0 0 0
-- Exhibit --
Two newly configured BGP peers have remained in the states shown in the exhibit for several
hours.
A. The TCP three-way handshake has completed successfully with the 10.1.1.1 peer.
B. The TCP three-way handshake has completed successfully with the 5.1.1.1 peer.
C. The local router has received a BGP keepalive message from the 5.1.1.1 peer.
D. The local router is initiating a transport protocol connection with the 10.1.1.1 peer.
QUESTION NO: 99
-- Exhibit --
Reject
[edit]
policy-statement adv-route {
term t1 {
from {
protocol isis;
then accept;
term t2 {
then reject;
[edit]
group ebgp {
type external;
neighbor 192.168.12.1 {
peer-as 65000;
-- Exhibit --
Referring to the exhibit, why is the 200.1.0.0/16 prefix failing to be advertised in BGP?
Answer: D
Explanation:
-- Exhibit
You are asked to configure a new external BGP peering. You have configured BGP on R1 as
shown in the exhibit, however the BGP peering remains in Active state.
Answer: C
Explanation:
-- Exhibit --
AS path: 65001 I
AS path: 65001 I
AS path: 65001 I
AS path: 65001 I
Restart Complete
Reject
Reject
Reject
Reject
Reject
export export-200;
group c5 {
neighbor 192.168.100.2 {
export export-200.200;
peer-as 65002;
term 1 {
from {
then accept;
term 1 {
from {
then accept;
-- Exhibit --
R2 is exporting static routes to R1 using BGP. R1 is not receiving one of the five static routes that
is configured on R2.
Referring to the exhibit, what should be changed under the BGP configuration to resolve this
issue?
Answer: B
Explanation:
-- Exhibit --
unit 0 {
family inet {
address 192.168.100.1/30;
autonomous-system 65001;
group 65002 {
traceoptions {
file bgp-trace;
neighbor 192.168.100.3 {
peer-as 65002;
20:45:44.212833 Out
Device Media Type Extension TLV #3, length 1, valuE. Ethernet (1)
Logical Interface Encapsulation Extension TLV #6, length 1, valuE. Ethernet (14)
-----original packet-----
80:71:1f:c7:f8:60 > 84:18:88:8e:3b:3f, ethertype 802.1Q (0x8100), length 82: vlan 435, p 6,
ethertype IPv4, (tos 0xc0, ttl 255, id 19548, offset 0, flags [DF], proto: TCP (6), length: 64)
192.168.100.1.bgp > 192.168.100.2.49373: S 1088527795:1088527795(0) ack 214564428 win
16384
20:45:44.213226 In
Juniper PCAP Flags [Ext, no-L2, In], PCAP Extension(s) total length 22
Device Media Type Extension TLV #3, length 1, valuE. Ethernet (1)
Logical Interface Encapsulation Extension TLV #6, length 1, valuE. Ethernet (14)
-----original packet-----
PFE proto 2 (ipv4): (tos 0xc0, ttl 1, id 2367, offset 0, flags [none], proto: TCP (6), length: 52)
192.168.100.2.49373 > 192.168.100.1.bgp: . 1:1(0) ack 1 win 17376
-- Exhibit --
Referring to the exhibit, what should be changed to the BGP configuration to bring up the peering?
Answer: A
Explanation:
-- Exhibit --
autonomous-system 65001;
group 65002 {
traceoptions {
file bgp-trace;
neighbor 192.168.100.2 {
peer-as 65002;
Feb 5 20:08:23.478040
Feb 5 20:08:23.478217 BGP SEND 4 Byte AS-Path capability (65), as_num 65001
Feb 5 20:08:23.478820
Feb 5 20:08:23.478974 BGP RECV 4 Byte AS-Path capability (65), as_num 65003
Feb 5 20:08:23.479104
Feb 5 20:08:23.479156 BGP SEND Notification code 2 (Open Message Error) subcode 2 (bad
-- Exhibit --
You have been asked to configure an EBGP peering to AS 65002. The EBGP peering is stuck in
an Active state.
Answer: D
Explanation:
-- Exhibit
-- Exhibit --
ge-0/0/0 0140.5501.1111
A. ge-0/0/0 FFFF.FFFF.FFFF
B. ge-0/0/0 FFFF.FFFF.FFFF
C. ge-0/0/0 0140.5501.2222
ge-0/0/1 0140.5501.3333
ge-0/0/1 0140.5501.4444
ge-0/0/0 0140.5501.1111
D. ge-0/0/0 0140.5501.2222
ge-0/0/1 0140.5501.3333
ge-0/0/1 0140.5501.4444
Answer: D
Explanation:
-- Exhibit
-- Exhibit --
In the exhibit, all switches run STP; however, the link between bridge G and bridge E fails.
What does root bridge A do after it receives information about this link failure?
A. Root bridge A sets the acknowledge flag and sends an updated topology BPDU.
B. Root bridge A sends a topology change notification BPDU.
C. Root bridge A sets the topology change flag and sends an updated configuration BPDU.
D. Root bridge A floods an updated BPDU topology database.
Answer: C
Explanation:
-- Exhibit --
Referring to the exhibit, you have an established RSVP LSP between R1 and R5 when you
experience a link failure between R2 and R4.
Answer: A,D
Explanation:
-- Exhibit --
[edit]
group ibgp {
type internal;
local-address 3.3.3.3;
family inet;
neighbor 2.2.2.2;
[edit]
VRF {
instance-type vrf;
interface xe-0/0/1.0;
route-distinguisher 3.3.3.3:100;
vrf-target target:100:100;
vrf-table-label;
[edit]
interface all;
[edit]
interface all;
-- Exhibit --
Referring to the exhibit, what is missing in the configuration to make the Layer 3 VPN functional?
(Choose two.)
A. a label-switched path
B. the LDP protocol configuration
C. a virtual circuit ID
D. an NLRI of family inet-vpn unicast
Answer: A,D
Explanation:
-- Exhibit --
xe-0/0/0 {
unit 0 {
family inet {
address 192.168.12.1/24;
family mpls;
xe-0/0/1 {
encapsulation ethernet-ccc;
unit 0 {
family ccc;
lo0 {
unit 0 {
family inet {
address 1.1.1.1/32;
[edit]
mpls {
interface all;
ospf {
traffic-engineering;
area 0.0.0.0 {
interface all;
ldp {
interface all;
l2circuit {
neighbor 2.2.2.2 {
interface xe-0/0/1.0 {
-- Exhibit --
In the exhibit, which configuration element is missing to bring up the Layer 2 circuit?
Answer: B
-- Exhibit
-- Exhibit --
Based on the exhibit, which configuration will permit end-to-end routing through the GRE tunnel for
R1?
A. [edit]
user@R1# show routing-options static
route 192.168.2.1/32 next-hop gr-0/0/0.0;
route 172.20.111.0/24 next-hop 192.168.1.1;
B. [edit]
user@R1# show routing-options static
route 192.168.2.1/32 next-hop gr-0/0/0.0;
route 172.20.111.0/24 next-hop 172.18.1.1;
C. [edit]
user@R1# show routing-options static
route 192.168.2.1/32 next-hop 172.18.1.1;
route 172.20.111.0/24 next-hop gr-0/0/0.0;
D. [edit]
user@R1# show routing-options static
route 192.168.2.1/32 next-hop 172.18.2.2;
route 172.20.111.0/24 next-hop 172.18.1.1;
Answer: C
Topic 2, Volume B
What are two valid actions that can be applied to a frame by a Layer 2 firewall filter?
(Choose two)
A. Log
B. loss-priority
C. sample
D. count
Answer: B,D
Explanation: The correct answers are B, D.
Reference:
* accept
* count counter-name
* discard
* forwarding-class class-name
* next term
* policer policer-name
* three-color-policer policer-name
Which two statements describe differences between IPv4 and IPv6? (Choose two)
Answer: A,D
Explanation:
You must configure an OSPF area that does not accept type 3 link-state advertisements (LSAs)
from area 0 (other than the default route) You have configured your area to be stub, but you still
see type 3 LSAs.
Answer: A
Explanation:
Which Junos operational mode command is used to verify that the tunnel interface is up and
operational?
Answer: C
Explanation:
A. IIH
B. LSP
C. PSNP
D. CSNP
Answer: A
Explanation:
Router A is an OSPF router connected to both Area 0 and Area 1 Area 1 has been configured as a
stub area Which two LSA types does Router A suppress from Area 1 ?
Answer: B,D
Explanation:
You are logged into a router and have navigated to the (edit routing-options] level of the hierarchy.
You have been asked to create a static route that will use 10.10.10.1 as its primary next-hop and
10.10.10.5 as its secondary next-hop.
Answer: C
Explanation:
Which Junos operational mode command is used to verify that load balancing is working as
expected?
Answer: D
Explanation:
Based on the illustration of the VPLS topology shown in the exhibit, which statement is true?
Answer: D
Explanation:
Which two values displayed in the output from the show spanning-tree MSTP configuration
command must match on all switches participating in the same MSTP region? (Choose two)
Answer: C,D
Explanation:
Which role does the router ID (RID) have in the BGP route selection process?
Answer: C
Reference:
http://www.juniper.net/techpubs/en_US/junos10.0/information-products/topic-collections/nog-
baseline/bgp-routes-and-selection-introduction.html
You are logged into a router and have navigated to the [edit routing-options] level of the hierarchy.
You have been asked to create a static route that will use 43 18 7 1 as its primary next-hop and 76
1310 2 as its secondary next-hop.
Answer: D
Explanation:
Referring to the network illustrated in the exhibit, how does router A reach destinations in area
49.2222?
A. Router A will use the routes from area 49.2222; it learns from router B
B. Router A will see the attached bit from router B and create a default route
C. Router A must have a default route manually configured
D. Router A will receive a default route in the IS-IS update from router B
Answer: B
Explanation:
You have recently implemented a graceful Routing-Engine switchover (GRES) and want to further
reduce down time if a Routing Engine (RE) failure occurs.
Which two features can be configured on this device to reduce its downtime in this situation?
(Choose two)
A. VRRP
B. GR
C. BFD
D. NSR
Answer: B,D
A. Established
B. Active
C. Operational
D. Connect
Answer: A
Explanation:
You work for the regional Internet service provider shown in the exhibit You have a partial BGP
table and are receiving a 10 100/16 route from your upstream ISP You have been asked to
configure a default route that can be sent to your downstream customer This route should forward
customer traffic toward your upstream Tier 11SP as long as the 10.100/16 route is present.
Answer: E
Reference:
http://www.juniper.fr/techpubs/en_US/junose10.0/information-products/topic-collections/swconfig-
bgp-mpls/advertising-a-default-route-only-when-another-route-is-present.html
In the exhibit, OSPF routers R1, R2, R3, and R4 come up, in order, at 1-minute intervals
A. R1
B. R2
C. R3
D. R4
Answer: A
You have been asked to configure an IPv6 address for a group of interfaces that could belong on
different routers. If a packet is sent to that address, it should be received by all routers in the
group.
A. Unicast
B. Multicast
C. Anycast
D. Broadcast
Answer: B
Explanation:
What is the function of the hop limit field in the IPv6 header?
Answer: C
Explanation:
You have been asked to define a default gateway for traffic leaving a router. This route should use
interface so-0/0/0 as its next-hop. Which type of route would be suited for this scenario?
A. a static route
B. a generated route
Answer: A
Explanation:
A. 0
B. 1
C. 2
D. 3
Answer: C
Explanation:
You are asked to design a Layer 2 switched topology that can automatically recover from link
failures.
A. GSTP
B. LLDP
C. LFM
D. MSTP
Answer: D
Explanation:
When the Junos configuration shown in the exhibit is applied to the router, which routes in the
forwarding table will begin load-balancing packet flows?
Answer: D
Explanation:
You have configured MPLS and RSVP in your network using all of the Junos defaults. You
established an LSP in your network which is reporting an up status but no traffic is using it.
Which two statements reflect potential causes for this issue? (Choose two)
Answer: C,D
Explanation:
Using industry best practices, what is true regarding an external BGP session?
Answer: C
Explanation:
You own a home network connecting through an always-on connection and need to assign IPv6
addresses to your routers because you want to follow the guidelines spelled out in RFC 3177. You
want to design your network with the correct prefixes.
A. 47-bit prefix
B. 48-bit prefix
C. 64-bit prefix
D. 128-bit prefix
Which two BGP attributes are modified by default when they are passed between external BGP
peers? (Choose two)
A. MED
B. AS-Path
C. Communities
D. Next Hop
Answer: B,D
Explanation:
In an RSTP network, the root and designated ports have been elected as shown in the exhibit
A. backup port
B. discarding port
C. alternate port
D. listening port
Answer: A
Explanation:
Answer: B,D
Explanation:
Which two elements contribute to the bridge ID when configuring RSTP? (Choose 2)
Answer: A,B
Explanation: The bridge ID consists of a configurable bridge priority and the MAC address of the
bridge.
Reference:
http://www.juniper.net/techpubs/software/junos/junos95/swconfig-layer-2/conf-stp.html#conf-
bridge-priority
Using industry best practices, which two BGP attributes would you modify to accomplish this goal?
(Choose two)
A. AS Path
B. Local Preference
C. Next Hop
D. MED
Answer: A,D
Explanation:
You have recently installed a second Routing Engine (RE) in your router
Which two statements correctly describe the expected behavior if the primary RE fails?
(Choose two.)
A. The backup RE will assume the master role once the packet forwarding engine restarts
B. The backup RE will immediately assume the master role
C. The new master RE restarts the routing protocol process (rpd) and establishes any required
adjacencies based on the configuration.
D. The new master RE maintains the existing protocol adjacencies initially established by the
previous master RE
Answer: A,C
Explanation:
Which command would you use to verify the presence of VPN routes on a PE device?
Answer: A
Explanation:
Answer: A
Explanation:
What are three circumstances under which a router sends link-state PDUs (LSPs)?
(Choose three)
Answer: B,C,E
Explanation:
In an RSTP network, which combination of port types can exist on the root bridge?
Answer: C
Explanation:
Your company has purchased two new Juniper Networks MX480 routers. Your manager has
asked you to add these two devices to the existing ISIS network.
Which two rules about ISIS adjacencies must you consider when carrying out the configuration?
(Choose two)
Answer: A,C
Explanation:
In the evaluation of an RSTP configuration BPDU, which two values are contained in the Bridge ID
value? (Choose two)
Answer: B,C
Explanation:
Answer: C
Explanation:
Which two configuration elements are defined under an MSTP instance? (Choose two)
A. revision-level
B. bridge-priority
C. mstp-level
D. vlan
Answer: B,D
Explanation: The correct answer is B, D because revision-level is common for the all MSTI
instances and it is configured one level up from MSTI instance section.
Reference:
http://www.juniper.net/techpubs/en_US/junos10.0/information-products/topic-collections/config-
guide-mx-series-layer2/mstp-edit-protocols.html
Given the network topology shown in the exhibit, you are configuring a GRE tunnel from Router A
to Router C
Which interface configuration on Router A will successfully allow the tunnel to pass IPv4 traffic to
Router C?
A. Option A
B. Option B
C. Option C
D. Option D
Answer: B
Explanation:
Answer: D
Explanation:
You have been asked to provision a service provider's network to accommodate Layer 3 VPNs as
defined in RPC 4364.
Answer: B,C,E
Explanation:
You would like two LDP routers on opposite sides of your network to become neighbors. Which
LDP message is used to form this relationship?
A. basic discovery
B. extended discovery
C. peer discovery
D. remote discovery
Answer: B
Explanation:
Answer: B,C
Explanation:
Answer: C
Explanation:
In the exhibit Router A and Router B are operating on the LAN with Router B acting as the
designated intermediate system (DIS).
When Router C and Router D are added to the LAN. Which statement is true?
Answer: A
Explanation:
You are logged into a router and issue the command show route protocol bgp. You see that you
have received the route 10 0.4/24 from two different peers Both peers were learned using IBGP
and Local-Preference. MED, Origin, and AS-path are equal.
A. cluster length
B. router ID (RID)
C. peer ID
D. IGP cost
Answer: D
Explanation:
How many equal-cost paths can be assigned to a single route in the Junos OS?
A. 4
B. 16
C. 32
D. 64
Answer: B
Explanation: http://www.juniper.net/techpubs/software/junos/junos70/swconfig70-
policy/html/policy-actions-config11.html
You want to configure support for an IPv6 environment In which hierarchy would you configure an
OSPF area?
Answer: D
Explanation:
Which action does the local router take after sending a Notification message to a remote peer?
Answer: B
You have been asked to configure and assign addresses for your IPv6 routers in your network
using dynamic assignment of DNS servers. You do not want the MAC address included as part of
the IPv6 address.
A. DHCP
B. stateless auto configuration
C. DHCPv6
D. stateful auto configuration
Answer: C
Explanation:
A. ring
B. tree
C. star
D. mesh
Answer: A,D
Explanation:
Which three functions are performed by an OSPF area border router (ABR)? (Choose three)
Answer: A,B,D
Explanation:
Which configuration will allow for the switch to potentially look at the IP header of incoming frames
tagged with a VLAN ID of 222?
A. Option A
B. Option B
C. Option C
D. Option D
Answer: D
Explanation:
Your area border router (ABR) receives type 1.2 and 5 link-state advertisements (LSAs) from a
non-backbone area.
A. The ABR will generate type 2 and 3 LSAs and flood type 5 LSAs to the backbone area
B. The ABR will generate only type 3 LSAs and flood only type 5 LSAs to the backbone area
C. The ABR will generate type 3 and 4 LSAs. And flood type 5 LSAs to the backbone area
D. The ABR will generate only type 4 LSAs and flood only type 5 LSAs to the backbone area
Answer: C
Explanation:
A. Pop
B. Push
C. Replace
D. Swap
Answer: B
Explanation:
An RSVP LSP in your network is operational but you are receiving complaints about network
throughput across the LSP. You suspect that the RSVP bandwidth was omitted from the router
configuration.
Which operational mode command will help you verify your suspicions?
Answer: B
Explanation:
After configuring OSPF between two routers you check for an adjacency. You see that the
adjacencies are not coming up on an Ethernet segment.
What are two reasons that would cause this situation? (Choose two)
Answer: A,B
Explanation:
Answer: A
Explanation:
You want to ensure that your RSVP LSPs are following a particular path across the network.
Answer: A
A. Layer 2 VPNs require that CE devices use the same Layer 2 encapsulation
B. Layer 2 VPNs do not permit CE devices to operate a Layer 3 protocol with each other
C. Service provider routers must evaluate the IP header of packets as they traverse their network
D. Layer 2 VPNs allow CEs to use different encapsulations on either side of the VPN
Answer: D
Explanation:
Based on the illustration shown in the exhibit, what would PE-B do with a VPLS packet received
from PE-A if the matching entry in its VPLS routing table showed the destination was connected to
PE-D?
Answer: C
Explanation:
Based on the configuration shown in the exhibit, which command would you use to display real-
time hellos and errors for IS-IS?
Answer: B
Explanation:
An Ethernet bridge is configured such that all interfaces are in a single broadcast domain By
default.
Which two tasks does the bridge perform in response to receiving a multicast frame?
(Choose two)
Answer: A,C
Explanation:
What must also be configured for this interface to participate in VLAN 100 and 200?
A. broadcast domains
B. VLANs
C. bridge domains
D. encapsulation type
Answer: C
You are logged into a PE router participating in a Layer 3 VPN as defined in RFC 4364. You would
like to ping the remotely connected CE router's loopback address. The address of the loopback is
122.161.2.1, the VPN routing-instance is called VPN-C. Which command will accomplish this
goal?
Answer: B
Explanation:
Which configuration can be applied to ensure that no more than 600 MAC addresses are learned
by a virtual switch?
A. Option A
B. Option B
C. Option C
D. Option D
Answer: C
Explanation:
You have two routers connected over a Gigabit Ethernet link as shown in the exhibit It is required
that an IS-IS adjacency be established without the need for a designated intermediate system
(DIS)
Which configuration statement entered on both routers will achieve this goal?
Answer: D
Explanation:
Answer: D
Explanation:
Which two problems occur when increasing numbers of users are added to an Ethernet LAN with
no switches present? (Choose two.)
Given the OSPF network topology shown in the exhibit, you would like to inject external (non-
OSPF) routes into the network on Router D
Which two OSPF area types will support this configuration? (Choose two)
A. stub area
B. totally stubby area
C. not-so-stubby area
D. non-backbone area
Answer: C,D
Explanation:
In your network, you have two LDP routers connected across four physical interfaces. You have
also enabled LDP to operate on all four of those interfaces.
What is the resulting outcome of your configuration between those two routers?
Answer: B
Explanation:
A. fixed explicit
B. fixed filter
C. shared explicit
D. wildcard filter
Answer: B
Explanation:
A. iBGP peering adds value in small networks with a single upstream connection
B. iBGP peering adds value in small networks with multiple upstream connections
C. eBGP peering adds value in small networks with multiple upstream connections
D. iBGP peering adds value in large enterprise environments with multiple upstream connections
E. eBGP peering adds value in large enterprise environments with multiple upstream connections
Answer: C,D,E
Explanation:
You observe that VPN routes are hidden on your PE router Which situation accounts for these
hidden routes?
Answer: A
Explanation:
To prevent fragmentation issues across a GRE tunnel, which MTU value is recommended for the
tunnel to accommodate most IP packets?
A. 1476
B. 1492
C. 1500
D. 1524
Answer: D
Explanation:
By default, which three criteria are used by the Junos load-balancing algorithm to determine a
traffic flow? (Choose three.)
A. protocol
B. source port
C. destination port
D. source address
E. destination address
Answer: A,D,E
Explanation:
Based on the configuration shown in the exhibit, what will be the state of the IS-IS levels on
interface ge-0/0/0.100?
Answer: D
Explanation:
Answer: B
Explanation:
Given the OSPF topology shown in the exhibit, how many unique link-state databases are present
in the network?
A. 1
B. 2
C. 3
D. 6
Answer: C
Explanation:
In the exhibit, three IPv6 addresses are listed. Which two statements are true? (Choose two.)
Answer: A,C
Explanation:
You have just configured IPv6 in your network. A packet arrives on your router that exceeds the
MTU size. How will an IPv6 router respond?
Answer: C
Explanation:
Which two statements reflect benefits of performing per-flow load balancing over per-packet load
balancing? (Choose two.)
Answer: B,C
Explanation:
By default, the Junos OS advertises which address(es) in LDP forwarding equivalency class (FEC)
messages?
Answer: C
Explanation:
A. encapsulation vlan-bridge
B. encapsulation ethernet-bridge
C. interface-mode trunk
D. vlan-id-range [100 200]
Answer: C
Explanation:
A. Refresh
B. Hello
C. Route
D. Keepalive
E. Open
Answer: A,D,E
Explanation:
What are two benefits of using an OSPF designated router (DR)? (Choose two.)
Answer: B,D
Explanation:
Answer: B,C,E
Explanation:
You have been asked to use a convention that allows for auto configuration of interface
addresses. You are not allowed to use DHCPv6. What do you do?
Answer: B
Explanation:
You notice that the RID of your router is being taken from the address of your management
interface.
Answer: C
Explanation:
You have been asked to identify what the contributing routes are for route 204.7.15/21. Which
command will show this information?
Answer: D
Explanation:
Which packet type does the router use to request up-to-date link-state information?
A. IIH
B. LSP
C. PSNP
D. CSNP
Answer: C
Explanation:
Which forwarding table designation is used to indicate that load balancing is working correctly?
A. ucst
B. msct
C. ulst
D. mlst
Answer: C
Explanation:
Which two statements are correct regarding VPLS mesh groups? (Choose two.)
A. Unicast packets destined to another PE router within the same mesh group are dropped by the
local PE router.
B. Unicast packets destined to another PE router in a different mesh group are dropped by the
local PE router.
C. Broadcast, multicast, and unicast packets of unknown origin received from a PE router are
flooded to all local CE routers.
D. Broadcast, multicast, and unicast packets of unknown origin received from a PE router are
flooded to all remote PE routers.
Answer: A,C
Explanation:
Router A receives two similar route advertisements from different BGP peers. What would cause a
route to be selected in this scenario?
Answer: A
Explanation:
Which two configuration elements must match on all switches participating in the same MSTP
region? (Choose two.)
A. mstp-version
B. configuration-name
C. msti-revision
D. revision-level
Answer: B,D
Answer: B
Explanation:
Answer: A,C
Explanation:
You are logged into a PE router participating in a Layer 3 VPN as defined in RFC 4364. You would
like to ping the locally connected CE router's interface. The address of the interface is
192.168.1.1; the VPN routing-instance is named VPN-A. Which command will accomplish this
task?
Answer: E
Explanation:
Before configuring an RSVP LSP in your network, you first apply a baseline configuration to all of
the routers. Which three configuration elements are minimally required in the baseline? (Choose
three.)
Answer: B,D,E
Explanation:
From the output shown in the exhibit, what would happen to a packet destined for address
172.29.3.5?
A. The address is not in the aggregate range; the packet is sent to the Routing Engine.
B. The address is in the aggregate range; the packet will be silently dropped.
C. The address is not in the aggregate range; the packet will be forwarded.
D. The address is in the aggregate range; the packet will be dropped.
Answer: A
Explanation:
Your customer complains that their Layer 3 VPN is not passing traffic from one site to another.
You assigned that customer to VPN-A. Which command on the PE router will confirm the
presence of customer routes?
Answer: D
Explanation:
Answer: A
Explanation:
Router B is an OSPF router connected to both Area 0 and Area 2. Area 2 has been configured as
a totally stubby area. Which three LSA types does Router B suppress from Area 2? (Choose four.)
A. Router LSA
B. Network LSA
C. External LSA
D. Summary LSA
E. ASBR Summary LSA
Answer: A,B,C,E
Explanation:
What is the size of the unique address used to identify each node on an Ethernet LAN?
A. 3 bytes
B. 6 bytes
C. 9 bytes
D. 12 bytes
Answer: B
Explanation:
Which two IS-IS packet types are used to maintain IS-IS database synchronization? (Choose two.)
A. IIH
B. LSP
C. PSNP
D. CSNP
Answer: C,D
Explanation:
You notice that a route from internal BGP peer 192.168.1.1 is missing from the local route table.
Which two commands would be used to help identify the source of the problem? (Choose two.)
Answer: B,C
Explanation:
What are three ways to configure IPv6 addresses in your network? (Choose three.)
Answer: A,B,C
Explanation:
Which two topologies shown in the exhibit could be implemented without a spanning-tree
protocol? (Choose two.)
A. ring
B. tree
C. star
D. mesh
Answer: B,C
Explanation:
In the exhibit, all routers are sending routes to Router B. Which routes will be advertised from
Router B to Router E?
Answer: D
Explanation:
In your RSVP network you have configured three separate LSPs to the same egress address. You
have made no other configuration changes to the forwarding decisions made by the router. Which
commands can you use to determine which LSP is being used to forward packets?
Answer: A
Which two values are used by an RSTP bridge to remove stale BPDU information? (Choose two.)
A. Message Age
B. Forwarding Delay
C. Hello Time
D. Max Age
Answer: A,D
Explanation:
After the MAC learning limit of 3000 is reached for the bd bridge domain as shown in the exhibit,
what happens to frames that arrive that contain unknown unicast destination addresses?
You have recently configured MSTP on two switches in your network to participate in the same
MSTP region. You issue the show spanning-tree mstp configuration command on both switches
and notice that the configuration digests do not match. What does this mismatch indicate?
A. Everything is functioning as expected because the configuration digests should not match.
B. You should ensure that the max-age and hello timers are equal on both switches.
C. You should ensure that the bridge IDs and priority values are unique on both switches.
D. You should ensure that the MSTIs and their VLAN IDs are equal on both switches.
Answer: D
Explanation:
You have a stub OSPF area running in your network. Your supervisor has asked you to build a
virtual link across this area to connect new equipment acquired in a recent ISP acquisition. Which
statement is correct about this scenario?
Answer: A
Explanation:
You own a small company and need to assign IPv6 addresses to your routers. Because you want
to follow the guidelines spelled out in RFC 3177, you want to design your network with the correct
prefixes. Which prefix would your ISP likely allocate to your company?
A. 47-bit prefix
Answer: B
Explanation:
Your customer would like to forward traffic using DLCI 600 and maintain Layer 2 information
across a VPN. Which solution will meet these requirements?
A. a Layer 3 VPN
B. a Layer 2 VPN
C. Virtual Private LAN Service (VPLS)
D. an IPsec VPN
Answer: B
Explanation:
You have two OSPF routers that are trying to form an adjacency. When you issue the command
show ospf neighbor, you see that one router is in the loading state and the other is in the full state.
Why are you seeing the router's state as loading?
A. The router does not know about the received LSA header and has transmitted a link-state
request.
B. The router has finished transmitting, but is still receiving database information.
C. The router is waiting for a start event.
D. The router has established bidirectional communication with its peer.
Answer: B
Explanation:
Which two events could cause the BGP Active state to appear? (Choose two.)
Answer: B,D
Explanation:
The policy shown in the exhibit has been configured and installed on your router.
Which type of router can provide connectivity between areas in an IS-IS domain?
Answer: B
Explanation:
You have been asked to provision a service provider's network to accommodate Layer 3 VPNs as
defined in RFC 4364. Which three tasks must be performed before the provider network is ready
to carry VPN traffic? (Choose three.)
A. All Juniper Networks PE routers must be configured with an appropriate router-ID unique to the
VPN.
B. All Juniper Networks PE routers must be configured with an appropriate route-target unique to
the VPN.
C. All Juniper Networks PE routers must be configured with a routing-instance of type forwarding.
D. All Juniper Networks PE routers must be configured with a routing-instance of type vrf.
E. All Juniper Networks PE routers must be configured with a routing-instance containing the CE-
facing interface.
Answer: B,D,E
Explanation:
By default, which BGP attribute is only compared when two route advertisements are received
from the same neighboring AS?
Answer: A
Explanation:
Referring to the exhibit, what must be true of the vlan_100 bridge domain?
Answer: D
Explanation:
An Ethernet bridge is configured such that all interfaces are in a single broadcast domain. Which
two tasks does the bridge perform in response to receiving a frame with an unknown unicast
destination MAC address? (Choose two.)
Answer: B,D
Explanation:
You have configured multiple IP-IP tunnels across your network to provide connectivity to remote
sites. Which technique is used to help the IP endpoints in your network determine the optimal
packet size to send across your tunnels?
Answer: A
Explanation:
You have configured an RSVP LSP in your network and have assigned it one primary and two
secondary paths.
Which command is used to validate that the LSP is using the primary path?
Answer: D
Explanation:
Answer: A,D
Explanation:
A. IIH
B. LSP
C. PSNP
D. CSNP
Answer: B
Explanation:
Which three statements are true regarding the show system switchover operational mode
command? (Choose three.)
Answer: B,C,E
Explanation:
Which three elements contribute to the bridge ID when configuring RSTP? (Choose three.)
Answer: B,C,E
Explanation:
Which LDP message is used to transmit labels and forwarding equivalency class (FEC)
information?
A. advertisement
B. discovery
C. notification
D. session
Answer: A
Explanation:
You are logged into a router and have navigated to the [edit routing-options] level of the hierarchy.
You have been asked to create a static route that will use 43.18.7.1 as its primary next-hop and
76.13.10.2 as its secondary next-hop.
Answer: D
Explanation:
By default, which Junos routing table stores RSVP egress router information?
A. inet.1
B. inet.2
C. inet.3
D. inet.4
Answer: C
Explanation:
You are logged into a router and have navigated to the [edit routing-options] level of the hierarchy.
You have been asked to define an aggregate route for 172.30/16.
Answer: B
Explanation:
When sending BGP routes in an Update message, how are they grouped?
Answer: B
Explanation:
You work for the regional Internet service provider shown in the exhibit. You have a partial BGP
table and are receiving a 10.100/16 route from your upstream ISP. You have been asked to
configure a default route that can be sent to your downstream customer. This route should forward
customer traffic toward your upstream Tier 1 ISP as long as the 10.100/16 route is present.
Answer: D
Explanation:
-- Exhibit --
interfaces {
ge-0/0/0 {
vlan-tagging;
vlan-id 100;
family inet {
address 192.168.100.97/30;
family iso;
unit 200 {
vlan-id 200;
family inet {
address 192.168.100.94/30;
family iso;
fxp0 {
unit 0 {
family inet {
address 10.210.10.11/27;
lo0 {
unit 0 {
family inet {
address 192.168.100.1/32;
family iso {
address 49.1111.1921.6801.0001.00;
protocols {
isis {
interface ge-0/0/0.100;
interface ge-0/0/0.200;
-- Exhibit --
Answer: A
Explanation:
ge-1/0/0 up up
fec0:0:0:2003::1/64
-- Exhibit --
You run the command show interfaces terse ge-1/0/0 and see the output shown in the exhibit.
A. Two addresses are assigned in IPv6, one for the physical and one for the logical interface.
B. Two addresses are seen because the loopback address of the router is associated with the
interface.
C. The two addresses being seen are the link-local and site-local.
D. An IPv6 address conflict is being seen; verify your interface configuration for problems.
Answer: C
Explanation:
-- Exhibit --
[edit]
term 1 {
from {
protocol bgp;
-- Exhibit --
Router-X has an external peering session to 10.0.21.2 and several internal peers.
How can the policy referenced in the exhibit be used to make sure routes are usable?
Answer: B
Explanation:
-- Exhibit --
protocols {
isis {
interface lo0.0;
interface ge-0/0/0.100;
-- Exhibit --
A. Level 1 only
B. Level 2 only
C. Level 1 and Level 2
D. Level 1, Level 2, and Level 3
Answer: C
Explanation:
Topic 3
You have three aggregate routes all with the same route preference.
Answer: B
Explanation:
You are configuring a trunk interface on an MX Series device and want to ensure that any
outgoing frames associated with VLAN 100 are transmitted as untagged frames.
A. routing-interface irb.0
B. vlan-id-list [100]
C. native-vlan-id 100
D. vlan-id 100
Answer: A
An RSVP enabled router receives an RSVP reservation message for a new RSVP path. The
router is unable to accommodate the reservation request.
Answer: D
Explanation:
What are two valid protocols used to signal VPLS in a network? (Choose two.)
A. RSVP
B. CCC
C. BGP
D. LDP
Answer: C,D
Explanation:
A. penultimate router
B. egress router
C. ingress router
D. ultimate router
You are asked to deploy OSPF between two routers over a broadcast medium.
Which three fields in the OSPF hello packet must match? (Choose three.)
A. hello interval
B. options
C. backup designated router
D. network mask
E. designated router
Answer: A,B,D
Explanation:
Which three STP protection mechanisms are supported on MX Series, EX Series, and QFX Series
devices? (Choose three.)
A. trunk protection
B. BPDU protection
C. loop protection
D. access protection
E. root protection
Answer: B,C,E
Explanation:
Answer: B
Explanation:
A. BGP routes are created using policies associated with BGP peering sessions.
B. BGP routes are created using IP subnet definitions at each defined BGP peer.
C. BGP routes are created based on interface subnets used for peering sessions.
D. BGP routes are created based on all interface subnets on all BGP routers.
Answer: A
Explanation:
What are two destination addresses used for OSPF link-state update packets? (Choose two.)
A. 224.0.0.1
B. 224.0.0.4
C. 224.0.0.6
D. 224.0.0.5
Answer: C,D
Explanation:
Which three statements are true about BGP default operations? (Choose three.)
A. IBGP peers advertise routes received from EBGP peers to other IBGP peers.
B. IBGP peers do not advertise routes received from IBGP peers to other IBGP peers.
C. IBGP peers do not advertise routes received from EBGP peers to other IBGP peers.
Answer: A,B,E
Explanation:
R1 is an OSPF router with a priority of 100 and has been elected as the designated router (DR).
R2 is the backup designated router (BDR) with a priority of 50. A third router, R3, comes online
with a priority of 200.
Answer: A
Explanation:
Referring to the exhibit, which two statements are correct about R2? (Choose two.)
Answer: A,B
Explanation:
Your network runs RSTP and includes a LAN segment shared by two MX Series devices. The two
MX Series devices sharing this LAN segment each have two connections on the shared segment.
A. The port on the selected MX Series device with the lowest port ID is selected as the designated
port.
B. The MX Series device with the highest-cost path to the root bridge is selected as a designated
bridge for the shared segment.
C. The port on the selected MX Series device with the highest port ID is selected as the
designated port.
D. The MX Series device with the least-cost path to the root bridge is selected as the designated
bridge for the shared segment.
Answer: A,D
Explanation:
Your network consists of multiple remote locations using both IPv4 and IPv6. You have an IPv4-
based Internet connection at each site provided by different, local service providers. You are
asked to ensure that the remote IPv6 networks are able to communicate.
A. Create GRE tunnels between the remote locations to connect the IPv6 networks.
B. Create IPsec tunnels between the remote locations to connect the IPv6 networks.
C. Create IP-IP tunnels between the remote locations to connect the IPv6 networks.
D. Create MPLS tunnels between the remote locations to connect the IPv6 networks.
You are asked to deploy OSPF between two routers over a point-to point link.
Which three fields in the OSPF hello packet must match? (Choose three.)
A. network mask
B. hello interval
C. options
D. dead interval
E. backup designated router
Answer: B,C,D
Explanation:
Which two Layer 2 protocols are supported on MX Series devices? (Choose two.)
A. BGP
B. RIP
C. RSTP
D. MSTP
Answer: C,D
Explanation:
Which two statements are correct according to the output shown in the exhibit? (Choose two.)
Answer: B,C
Explanation:
On an Ethernet segment, OSPF DROther routers from which type of adjacency with each other?
Answer: B
Explanation:
Answer: D
Explanation:
To which OSPF state does a device transaction once it receives an initial hello packet?
A. 2Way
B. Full
C. ExStart
D. Exchange
Answer: A
Explanation:
Which two statements are correct according to the output shown in the exhibit? (Choose two.)
Answer: B,C
Explanation:
Referring to the exhibit, which policy would be applied to the 75.217.12.10 neighbor?
Answer: D
Explanation:
Referring to the exhibit, all interswitch links are configured as trunks supporting all VLANs. Host A
sends a frame with an unknown destination MAC address to S2.
Answer: C
Explanation:
Which table will a Junos-based MPLS ingress router first consult to determine the next hop for
BGP routes reachable through an LSP?
A. inet.1
B. mpls.0
C. inet.3
D. inet.0
Answer: D
Explanation:
Which Layer 2 mechanism logically groups network nodes into separate broadcast domains?
A. IS-IS levels
B. OSPF areas
C. VLAN
D. IP subnets
Answer: C
Explanation:
Switch 1 and Switch 2 are configured to run MSTP. However, MSTP is not working.
Answer: C,D
Explanation:
You are asked to configure a new LSP in your network. The new LSP must take a specific path
using a given set of routers.
A. A named path must be defined and referenced as primary for the LSP.
B. A named path must be defined and referenced as preferred for the LSP.
C. A named path must be defined and given a low priority.
D. A named path must be defined and given a high priority.
Answer: A
Explanation:
Which three IPv6 addresses are valid equivalents for the address
2001:0000:0000:0000:0134:fc0e:cc8b:458a? (Choose three?)
A. 2001:134:fc0e:cc8b:458a
B. 2001:0:0:0:0134:fc0e:cc8b:458a
C. 2001:0:0:0134:fc0e:cc8b:458a
D. 2001::134:fc0e:cc8b:458a
E. 2001:0::0:134:fc0e:cc8b:458a
Answer: B,D,E
Explanation:
In the exhibit, R1, R2, and R3 are all IBGP peers within AS 65505. R1 receives a BGP
advertisement from an external BGP peer in AS 65555, and BGP advertisement from R3. The
default BGP advertisement behavior is in effect in this environment.
A. R1 will advertise the route received from R3 to R2 and its external BGP peer.
B. R1 will advertise the route received from R3 only to its external BGP peer.
C. R1 will advertise the route received from its external peer to R2 and R3.
D. R1 will not advertise the route received from its external peer to R2 or R3.
Answer: B,C
Explanation:
Which three statements are true about GRE and IP-IP tunnels? (Choose three.)
Answer: A,C,E
Explanation:
Which two statements are correct about a generated route? (Choose two.)
Answer: C,D
Explanation:
Answer: B,C,D
Explanation:
Answer: C
Explanation:
You are asked to configure a GRE tunnel between two remote sites to support the exchange of
IPv6 traffic. The two sites are separated by an IPv4 network.
Answer: C,D
Explanation:
A. bridge priority
B. bridge port priority and bridge port address
C. bridge priority and bridge address
D. port priority and port address
Answer: D
Explanation:
Answer: A,C
Explanation:
Which aggregate route would represent all four routes shown in the exhibit?
A. 10.10.0.0/19
B. 10.10.0.0/21
C. 10.10.0.0/20
D. 10.10.0.0/22
Answer: A
Explanation:
You are asked to configure an MC-LAG, in active-active mode, between PE1 and PE2.
A. Option A
B. Option B
C. Option C
D. Option D
Answer: D
Explanation:
A. topology
B. vector
C. length
D. value
Answer: C,D
Explanation:
Which two routing protocols make use a designated router, or pseudo node, to represent a
broadcast network? (Choose two.)
A. BGP
B. OSPF
C. MPLS
D. IS-IS
Answer: B,D
Explanation:
Your customer requests that you provide a transparent Layer 2 service between two of their
remote locations. This service must allow them to pass tagged traffic from multiple VLANs. You
decide to use Q-in-Q tunneling on the two provider edge MX Series routers that connect to the
customers CE devices.
Answer: B,C
Explanation:
You have multiple Layer 2 interfaces associated with different VLANs configured on an MX Series
router. You have been asked to ensure Layer 3 reachability through the MX Series router for the
subnets associated with the different VLANs.
Answer: A
Explanation:
Answer: A
Explanation:
Which two elements are valid in the BGP path selection algorithm? (Choose two.)
Answer: B,D
Explanation:
Which two formats are valid route distinguisher formats? (Choose two.)
Answer: B,D
Explanation:
Referring to the exhibit, what is required to establish an IS-IS adjacency between these two
routers?
A. The interface connecting the two routers must be configured as a Level 2 interface.
B. Both routers will require wide metrics to be enabled.
C. The interface connecting the two routers must be configured as a Level 1 interface/
D. Router A must be configured as the designated intermediate system (DIS).
On an MX Series device with dual Routing Engines, which two conditions cause a unified ISSU to
fail? (Choose two.)
Answer: C,D
Explanation:
You are asked to deploy a large-scale IS-IS network with multiple areas.
A. A collection of Level 1 routers in different areas constitute the backbone in the network.
B. Level 2 routers can route between areas.
C. Level 1 routers can route between areas.
D. A collection of Level 2 routers in different areas constitute the back bone in the network.
Answer: B,D
Explanation:
A. VRRP
B. BFD
Answer: A
Explanation:
Which high availability feature allows uninterrupted packet forwarding and temporary suppression
of all routing protocol updates?
Answer: B
Explanation:
You are using RSVP in your network to signal MPLS LSPs. You are asked to ensure that the
egress MPLS router receives the full label stack, containing both the hop-by-hop and VPN label.
Answer: A
Explanation:
Answer: A,C
Explanation:
What are two valid statements for virtual switches on MX Series devices? (Choose two.)
Answer: A,B
Explanation:
Referring to the exhibit, which two statements are correct? (Choose two.)
Answer: B,D
Explanation:
Referring to the exhibit, which static route will be exported into OSPF?
A. 172.29.0.0/16
B. 172.29.0.0/17
C. 172.28.0.0/24
D. 172.29.0.0/24
Answer: D
Explanation:
In the exhibit, which configuration is required to establish a single adjacency between the two IS-
IS routers?
Answer: A
Explanation:
In an IS-IS network, Router A is the current DIS with a priority of 64. Router B comes online with a
priority of 100.
Answer: C
Explanation:
Answer: B
Explanation:
An ISO NET has been configured on R2s lo0.0 interface and ge-0/0/2.0 has been configured to
run IS-IS. However, IS-IS adjacency on ge-0/0/2.0 is not coming up.
Answer: A
Explanation:
You are asked to deploy a large-scale IS-IS network with multiple areas.
A. A router configured for Level 1 only informs all Level 2 routers in the area of external
Answer: D
Explanation:
In a Junos device functioning as an MPLS transit router, which routing table is used when
performing a forwarding lookup for an incoming packet?
A. mpls.3
B. inet.0
C. inet.3
D. mpls.0
Answer: C
Explanation:
Referring to the exhibit, MED is being used in your BGP network. All other BGP configurations use
the default settings.
Which statement is correct regarding traffic destined to the 151.213.0.0/16 prefix in AS 358?
Answer: C
Explanation:
Referring to the exhibit, four IS-IS routers have been deployed on a multi-access Ethernet
segment. Router C came online first.
After all routers are online, which two statements are true? (Choose two.)
Answer: B,C
Explanation:
For two switches to participate in the same Multiple Spanning Tree Protocol (MSTP) region, which
three values must match? (Choose three.)
A. extended system ID
B. region name
C. member VLAN ID list
Answer: A,C,E
Explanation:
In the exhibit, R1 is sending the 172.16.100.0/24 route to R2 through EBGP. R2 has IBGP
sessions to R3 and R4, but they are not installing the route. All BGP sessions are established.
Answer: A,C
Explanation:
What is the correct format for an IPv4 address mapped into IPv6?
A. ::192:168:0:1
B. ::FFFF:192.168.0.1
C. ::FFFE:192:168:0:1
D. ::192.168.0.1:FFFF
Answer: B
Explanation:
You are deploying IS-IS in your network to enable the routing of only IPv6. Assume that the
loopback interface has been properly configured.
What is the minimum required configuration to enable only IPv6 routing in IS-IS?
Your customer requests that you provide a transparent Layer 2 service between two of their
remote locations. This service must allow the customer to pass tagged traffic from multiple VLANs.
You decide to use Q-in-Q tunneling on the two provider edge MX Series routers that connect to
the customers CE devices.
A. As traffic leaves the Q-in-Q tunnel, the S-VLAN tag will be removed from the frames.
B. As traffic enters the Q-in-Q tunnel, an S-VLAN tag will be added to the frames.
C. As traffic enters the Q-in-Q tunnel, a C-VLAN tag will be added to the frames.
D. As traffic leaves the Q-in-Q tunnel, the C-VLAN tag will be removed from the frames.
Answer: A,B
Explanation:
Answer: B,C,E
Explanation: