Professional Documents
Culture Documents
Huawei eRAN KPI Introduction (eRAN 6.0) : Company Confidential
Huawei eRAN KPI Introduction (eRAN 6.0) : Company Confidential
3. Recommended KPIs
RRC SETUP Call Drop HHO SR ( Radio UL/DL Cell UL/DL Access Service
SR Rate Intra/Inter Network RB Traffic Latency UL/DL
(VoIP/ALL) Frequency Unavailabi Utility Volume Throughput
ERAB Service
) lity Rate Rate
Setup SR Call Setup Radio Latency
(VoIP/ALL) Complete HO in SR Bearer
Interrupt
Rate Number
Call Setup Inter-RAT Latency
SR (VoIP/ALL)
HHO SR
(VoIP/ALL)
Measurement Object
o Accessibility
o Retainability
o Mobility
o Availability
o Utilization
o Traffic
o Integrity
o Latency
L.RRC.ConnReq.Att
L.RRC.ConnReq.Succ
ERAB _ SetupSuccess
ERAB _ SSR( ALL) 100%
ERAB _ SetupAttempt
This KPI can be used to evaluate the call drop rate of VoIP service (QCI 1 service) in a cell
or cluster, the call drops happen when eNode initiate active ERAB (with data in buffer)
release process by E-RAB Release Indication or UE Context Release Request message with
Cause field with abnormal reasons (the cause other than : Normal Release, Detach,User
Inactivity, cs fallback triggered, UE Not Available For PS Service,or Inter-RAT redirection),
and all of the other E-RAB releases are consider as normal E-RAB release.
Handover Attempt
Counters
Handover Success
Counters
HOInSuccess
HOIn _ SR 100%
HOInAttempt
HO in Attempt
Counters
HO in Success
Counters
C point, HO
Success
Where the {SP} denotes the reports period of counters, and the unit is minutes.
The ULRB_Available and DLRB_Available are fix values, which can be calculated by
system bandwidth.
MeanCPUUtility
o Active Users
This group of KPIs consist of 6 KPIs, which are used to evaluate the user numbers which
has the RRC connection in the cell, the user numbers with uplink data in the buffer or
with downlink data in the buffer, and also give the average user number and maximum
user number in a cell or cluster.
AvgUserNumber
MaxUserNumber
AvgUserNumber _ DLData
MaxUserNumber _ DLData
AvgUserNumber _ ULData
MaxUserNumber _ ULData
o Radio Bearers
The radio bearers KPIs consist of ten sub-KPIs, one is for the total of radio bearers and
the other nine are for nine QCIs. This set of KPIs can be used to evaluate the average
radio bearers in a cell or a cluster. The radio bearer for each QCI is based on the number
of active RRC connections for each QCI according to the QCI defined in the QoS
information.
RadioBearers
RadioBeare rs _ QCI _ 1
RadioBeare rs _ QCI _ 9
The total downlink traffic volume at PDCP layer of each QCI and total duration for
transmitting them are measured within a measurement period. Then the average
throughput of each QCI is obtained at the end of the measurement period.
CellULMaxTrafficVolumeforEach1s(bit )
CellULMaxThp
1000(ms)
Refer to TS 32.450
o Access Latency
This grouped KPI can be used to evaluate the
latency of access phase.
o AccessLatency_Attach
Defined as the duration from the time the UE
send AttachRequest message to the time the
UE send AttachComplete message message
o AccessLatency_Idle2Active
Defined as the duration from (UE in idle mode)
the time the UE send RRCConnectionRequest
message to the time the UE send
RRCConnectionReconfiguration message
This KPIs is measured through drive test. Defined as the duration from the time the UE
receives the handover commandRRCConnectionReconfiguration after
MeasurementReport) to the time the UE send the handover confirm message
(RRCConectionReconfigurationComplete) .
ControlPla ne _ Interrupt _ IntraLTE _ HO
ControlPla ne _ Interrupt _ IRATHO _ L2C
ControlPla ne _ Interrupt _ IRATHO _ L2W
ControlPla ne _ Interrupt _ IRATHO _ L2G
This KPIs is measured through drive test. UserPlane _ Interrupt _ IRATHO _ L2W
UserPlane _ Interrupt _ IRATHO _ L2G
Defined as the duration from the last RLC layer
package received before the handover, to the
first RLC layer package received after handover.
It can be observed in Probe.