Professional Documents
Culture Documents
Performance Sheet Drill Pipe: Pipe Body: Tubular Assembly
Performance Sheet Drill Pipe: Pipe Body: Tubular Assembly
Tensile Strength (lbs): 1,139,808 1,077,781 1,016,285 894,882 Upset Type: IEU Fluid Capacity w/o IPC (gal/ft): 0.93
Torsional Strength (ft-lbs): 135,921 128,327 120,825 106,096 Max Upset OD (in): 6.000 Fluid Capacity w/o IPC (bbls/ft): 0.0221
Drift Size (in): 4.125
Burst Capacity (psi): 20,106 21,830 20,681 18,383
Collapse Capacity (psi): 21,023 19,719 18,115 14,824
18
0
Note: These are OEM values that may vary with actual values due to mill tolerances, IPC tolerances, OEM rounding, and other
Notes: Body properties are calculated based on uniform OD and wall thickness. factors. Pipe is purchased at a guaranteed 95% RBW. IPC is applied to a nominal thickness of 0.009''. Pipe will have an ID of
Burst capacity for Nominal (100% RBW) based on 87.5% RBW per API. 4.801'', which is smaller than pipe purchased at 87.5%.
Internal Pressure Rating (psi): 15,000 Tool Joint Torsional Strength (ft-lbs): 96,600
External Pressure Rating (psi): 10,000 Tool Joint Tensile Strength (lbs): 1,350,600
CTM57 is a trademark of NOV Grant-Prideco. Note: Elevator capacity based on assumed elevator bore, no wear factor, and contact stress of 110, 100 psi. An increased
Note: MUT values are based on a friction factor of 1.0. elevator shoulder OD increases elevator capacity without affecting make-up torque.
The technical information containted herein, including the product performance sheet and other attached documents, has been extracted from information available from the manufacturer and is for reference only and not a recommendation. The user is fully responsible for the accuracy and suitability of use of the technical
information. Workstrings International cannot assume responsibility for the results obtained through the use of this material. No expressed or implied warranty is intended. Drill pipe assembly properties are calculated based on uniform OD and wall thickness. No safety factor is applied. The information provided for various
inspection classes and for various wear conditions (remaining body wall) is for information only and does not represent or imply acceptable operation limits. It is the responsibility of the customer and the end user to determine the appropriate performance ratings, acceptable use of the product, maintain safe operational practices,
and to apply a prudent safety factor suitable for the application. For API connections that have different pin and box IDs, tool joint ID refers to the pin ID. Per Chapter B, Section 4 VII of the IADC drilling manual, it is recommended that drilling torque should not exceed 80% of MUT.
www.workstringsinternational.com 08-Sep-15
Download the Workstrings International Pipe Specification App on the App Store or Google Play
Operational Limits of Drill Pipe
Connection CTM57 Tool Joint OD (in) 7.000 Tool Joint ID (in) 4.250 Tool Joint Specified Minimum 135,000
Yield Strength (psi)
Pipe Body 80 % Inspection Class Pipe Body OD (in) 5.875 Wall Thickness (in) 0.500 Pipe Body Grade S-135
Combined Loading for Drill Pipe at Combined Loading for Drill Pipe at
Maximum Make-up Torque = 51,500 (ft-lbs) Minimum Make-up Torque = 42,900 (ft-lbs)
Operational Assembly Pipe Body Connection Max Operationa Assembly Pipe Body Connection
l Torque Max Tension Max Tension Max Tension
Torque Max Tension Max Tension Tension
(ft-lbs) (lbs) (lbs) (lbs) (ft-lbs) (lbs) (lbs) (lbs)
Connection
Make-up Torque Range
Make-up Torque Connection Max
(ft-lbs) Tension (lbs)
Min MUT 42,900 1,163,500
43,900 1,190,600
44,800 1,215,000
45,800 1,242,200
46,700 1,266,600
47,700 1,293,700
48,600 1,318,100
49,600 1,345,200
50,500 1,330,200
Max MUT 51,500 1,301,400
Note: Recommended MUT should always be used when possible. If not possible, MUT should be as close to Recommended MUT as possible.
Note: The technical information contained herein, including the product performance sheet and other attached documents, is for reference only and should not be construed as a recommendation. The user is fully responsible for the accuracy and
suitability of use of the technical information. NOV Grant Prideco cannot assume responsibility for the results obtained through the use of this material. No expressed or implied warranty is intended. Drill pipe assembly properties are calculated
based on uniform OD and wall thickness. No safety factor is applied. The information provided for various inspection classes and for various wear conditions (remaining body wall) is for information only and does not represent or imply acceptable
operating limits. It is the responsibility of the customer and the end user to determine the appropriate performance ratings, acceptable use of the product, maintain safe operational practices, and to apply a prudent safety factor suitable for the
application. For API connections that have different pin and box IDs, tool joint ID refers to the pin ID. Per Chapter B, Section 4 VII of the IADC drilling manual, it is recommended that drilling torque should not exceed 80% of MUT.
06-17-2015