Professional Documents
Culture Documents
Koleos Manual
Koleos Manual
DRIVERS HANDBOOK
recommends ELF
Important: to optimize engine operation the use of a lubricant
may be restricted to certain vehicles. Please refer to the
maintenance documentation.
ELF is developing a complete range of
lubricants for RENAULT: engine oils, manual
and automatic transmission oils.
RENAULT recommends the approved ELF lubricants for your oil changes and top-ups.
Contact your RENAULT representative or visit the site: www.lubricants.elf.com
The descriptions of the models given in this handbook are based on the technical specifications at the time of writing. This hand-
book covers all items of equipment (both standard and optional) available for these models but whether or not these are
fitted to the vehicle depends on the version, options selected and the country where the vehicle is sold.
This handbook may also contain information about items of equipment to be introduced later in the model year.
Throughout the manual, the approved Dealer is your RENAULT Dealer.
Translated from French. Copying or translation, in part or in full, is forbidden unless prior written permission has been obtained from the vehicle manu-
facturer.
0.1
0.2
C O N T E N T S
Sections
Driving ................................................................... 2
Maintenance .......................................................... 4
0.3
0.4
Section 1: Getting to know your vehicle
RENAULT cards: general information, use, deadlocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2
Doors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.9
Automatic locking of opening elements when driving. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.13
Headrests/Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.14
Seat belts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.18
to the rear seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.20
Additional methods of restraint:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.22
to the front seat belts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.22
to the rear seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.26
side protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.27
Child safety: general information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.29
choosing a child seat mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.32
fitting a child seat. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.34
deactivating/activating the front passenger airbags. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.37
Driving position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.40
Warning lights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.44
Instrument panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.48
trip computer and warning system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.50
Clock and exterior temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.60
Steering wheel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.61
Power-assisted steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.61
Rear-view mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.62
Audible and visual signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.63
Exterior lighting and signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.64
Electric beam height adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.67
Front windscreen wash/wiper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.68
Rear windscreen wash/wiper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.70
Fuel tank. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.71
1.1
RENAULT cards: general information (1/2)
The RENAULT card is used RENAULT card operating
for: range
locking and unlocking the doors and This varies according to the surround-
2 3 tailgate (refer to the following pages); ings: It is important to make sure when
depending on the vehicle, automati- handling the RENAULT card that you
1 cally closing the electric windows do not lock or unlock the doors by inad-
and sunroof remotely (see the in- vertently pressing the buttons.
4 formation on "Electric windows" and
"Electric sunroof" in Section 3);
switching on the vehicle lighting re-
motely (refer to the following pages); When the battery is flat, you can
starting the engine (refer to the in- still lock/unlock and start your ve-
5 formation on "Starting the engine" in hicle. Refer to the information on
Section 2). Locking/unlocking the doors in
Section 1 and Starting the engine
in Section 2.
1 Unlocking the doors and the tailgate; Battery life
Make sure that the correct battery type
2 Locking the doors and the tailgate;
is being used, and that the battery is in
3 Switching on the lighting remotely; good condition and inserted correctly. Drivers responsibility
4 Unlocking/locking the tailgate; Its service life is approximately two Never leave your vehicle
years: replace it when the message with the Renault card inside
5 Integrated key. "Low card battery" appears on the in- and never leave a child
strument panel (refer to the informa- (or a pet) unsupervised, even for a
tion on the "RENAULT card: Battery" in short while.
Section 5). They may pose a risk to themselves
or to others by starting the engine,
activating equipment such as the
electric windows or by locking the
doors.
Risk of serious injury.
1.2
RENAULT cards: general information (2/2)
Access to key 5
Press button6 and pull on key5 then
release the button.
1.3
REMOTE CONTROL RENAULT CARDS : use
Locking the doors Distance lighting function
Press the locking button2. This can, for example, identify the ve-
2 The hazard warning lights flash twice hicle from a distance when parked in a
3 car park.
1 to indicate that the doors have locked:
if a door or the boot is open or not prop- The dipped beam headlights, indicator
erly shut, or if a RENAULT card is still in lights and interior lights come on for ap-
4 the reader, the doors and boot quickly proximately 30 seconds when button3
lock then unlock and the hazard warn- is pressed.
ing lights and indicator lights do not Note: pressing button3 again switches
flash. off the lighting.
1.4
RENAULT "hands-free" card: use (1/3)
2 3
1.5
RENAULT "hands-free" card: use (2/3)
2
5
4
1
1.6
RENAULT "hands-free" card: use (3/3)
With the engine running, if, after
having opened and closed a door, the
card is no longer in the passenger com-
6 partment, the message card not de-
tected (accompanied by a beep when
the speed passes a certain level) warns
you that the card is no longer in the
vehicle. This avoids you driving away
7 after having dropped off a passenger
who has the card, for example.
The warning disappears when the card
is detected again.
1.7
RENAULT CARD: deadlocking
To lock the vehicle, without
deadlocking
2 Press button2 or3 twice.
1 Note: to raise the windows simultane-
3 ously, the second time the button is
pressed, it must be held down for more
than one second.
The hazard warning lights flash twice
to indicate that the doors have locked.
Warning: deadlocking is
activated the first time
button1 is pressed. After activating deadlocking using
button2, hands-free unlocking is
Never use deadlocking if deactivated.
someone is still inside the vehicle.
To reactivate the hands-free mode:
restart the vehicle.
1.8
Opening and closing the doors (1/2)
Card reminder buzzer
A beep will let you know if you have left
the card in the reader when you open
the drivers door, and the Remove
card message will appear on the in-
strument panel.
1 Special note
2
After switching off the engine, the lights
and some accessories that are in op-
eration (radio, etc.) will continue to op-
erate.
They stop as soon as the drivers door
is opened.
As a safety precaution,
the doors should only be
opened or closed when the
vehicle is stationary.
1.9
Opening and closing the doors (2/2)
Child safety
Manually locking the rear doors
Move lever3 and check from the inside
that the doors are securely locked, to
prevent the rear doors being opened
from the inside. Drivers responsibility when parking or stopping the vehicle
Never leave an animal, child or adult who is not self-sufficient alone on
your vehicle, even for a short time.
They may pose a risk to themselves or to others by starting the engine, activating
equipment such as the electric windows or by locking the doors.
Also, in hot and/or sunny weather, please remember that the temperature inside
the passenger compartment increases very quickly.
RISK OF DEATH OR SERIOUS INJURY.
1.10
LOCKING/UNLOCKING THE DOORS (1/2)
Locking/unlocking the doors
from the outside
This is done using the RENAULT
Card; refer to the information on the
RENAULT Card" in Section 1.
A
In certain cases, the RENAULT card 3
may not work:
when the RENAULT card battery is
drained, flat battery, etc.
use of appliances operating on the 1
same frequency as the card (mobile
phone, etc.); 2
vehicle located in a high electromag-
netic radiation zone.
Using the key integrated in Locking the doors manually
It is then possible:
the RENAULT card Turn screw3 with the door open (using
to use the key integrated into the the end of the key) and close the door.
Take out the integrated key (refer
card to unlock the front left-hand
to the section on RENAULT cards: This means that the doors are then
door;
general information" in section 1); locked from the outside.
to lock each of the doors manually
remove coverA from the left-hand The doors may then only be opened
(see the following page);
door (using the end of key2) in from the inside or by using the key in
to use the interior door locking/un- notch1; the front left-hand door.
locking control (refer to the following
move it upwards to remove coverA;
pages).
insert the key2 into the lock in the
front left-hand door and lock or
unlock.
1.11
LOCKING/UNLOCKING THE DOORS (2/2)
Locking the opening Doors and tailgate status
4 elements without the indicator light
RENAULT card When the ignition is on, the indicator
(if the RENAULT card is not working, for light integrated in switch4 informs you
example) of the status of the doors and tailgate:
With the engine switched off and a indicator light on, the doors and tail-
front door open, press switch4 for gate are locked;
more than five seconds.
indicator light off, the doors and tail-
When the door is closed, all the doors gate are unlocked.
and the tailgate will be locked.
When you lock the vehicle from the out-
Unlocking the vehicle from the outside side, the indicator light remains lit for
will only be possible with the RENAULT approximately one minute, then goes
card. out.
Interior locking/unlocking
door control
The switch4 simultaneously controls
the doors and the tailgate.
If a door or the tailgate is open or not
closed properly, the doors and tailgate
lock/unlock quickly.
If transporting an object with a door
or tailgate open: with the engine
stopped, press the switch4 for more Drivers responsibility
than five seconds to lock the other Drivers responsibility If you decide to keep the
opening elements. doors locked when you are
Never leave your vehicle
with the RENAULT card driving, remember that it
inside. may be more difficult for those as-
sisting you to gain access to the
passenger compartment in the
event of an emergency.
1.12
RAID (Renault Anti-Intruder Device)
To activate this function: Operating faults
1 After switching on the ignition and If you experience an operating fault (no
when the vehicle is stationary, you automatic locking, the indicator light in-
have approximately 20 seconds to corporated in button1 does not light up
press and hold door locking switch1 when trying to lock the doors and tail-
(for approximately 5 seconds). gate, etc.), firstly check that the doors
The message automatic door locking and tailgate are properly closed. If they
activated is displayed on the instru- are closed correctly, contact an ap-
ment panel and a beep sounds. proved dealer.
1.13
FRONT HEADRESTS
To remove the headrest
Raise the headrest as far as possible,
then while pressing button1, raise the
headrest to release it.
1.14
REAR HEADRESTS
A A
1 2
1.15
Front seats (1/2)
To raise or lower the seat base
(depending on vehicle)
Move lever4 as required:
move it upwards to raise the seat;
move it downwards to lower the seat.
1 3
4 5
1.16
FRONT SEATS (2/2)
6 7
8
To fold down the passenger seat To adjust the lumbar support on the Heated seats
Depending on the vehicle, the passen- drivers seat: (depending on vehicle)
ger seatback may be folded down onto Move lever7.
the seat base to create a table. With the engine running, press
Lift handle6 and lower the seatback. switch8, pressing on the top of the
switch (to select the warmest setting) or
the bottom of the switch (to select the
average setting).
The indicator light on the button lights
Since front passenger airbag operation and the position of a front pas- up.
senger seatback table are incompatible, ensure that the airbag is deac- The system, which has a thermostat,
tivated. (Refer to the information on Front passenger air bag activation/ decides whether or not the heating is
deactivation in Section 1). needed, according to the position se-
There is a risk of very serious injury if the air bags deploy. lected.
When driving, rear passengers must not place their feet on the seatback of the If the heated front passenger seat is ac-
front seats under any circumstances. Risk of injury.
tivated, the indicator light
up on the instrument panel.
lights
1.17
SEAT BELTS (1/2)
Always wear your seat belt when trav- Before starting, first adjust your driv-
elling in your vehicle. You must also ing position, then ask all occupants
comply with the legislation of the par- to adjust their seat belts to ensure
ticular country you are in. optimum protection.
1.18
SEAT BELTS (2/2)
8
1 6
7
3 4
5
5
Fastening
Unwind the belt slowly and smoothly
Front passenger seat belt re-
minder warning light
This lights up when the engine is
Adjusting the height of the
front seat belts
and ensure that buckle3 locks into started on the instrument panel6 or on Press button 8 to adjust the seat belt
catch5 (check that it is locked by pull- the centre console 7 if the front pas- height so that the shoulder strap 1 is
ing on buckle3). If the belt jams, allow senger seat belt (if this seat is occu- worn as shown previously:
it to return slightly before attempting to pied) is not fastened and the vehicle to lower the seat belt, press button8
unwind it again. has reached approximately 15 mph and lower the seat belt at the same
If your seat belt is completely jammed, (25kph); it flashes and a bleep sounds time;
pull slowly, but firmly so that just over for approximately 90 seconds. to raise the seat belt, press button8
3 cm unwinds. Allow it to return slightly and raise the seat belt at the same
Note: an object placed on the passen- time.
before attempting to unwind it again. ger seat base may activate the warning
If there is still a problem, contact an ap- light in some cases. Make sure that the seat belt is locked
proved dealer. in position correctly after you have ad-
justed it.
Unfastening
Press button4 and the seat belt will be
rewound by the inertia reel. Guide the
belt.
1.19
REAR SEAT BELTS
3
4
5
1.20
SEAT BELTS: warnings
The following information applies to the vehicles front and rear seat belts.
No modification may be made to the component parts of the originally fitted restraint system: belts, seats and their
mountings. For special operations (e.g. fitting child seats) contact an authorised dealer.
Do not use devices which allow any slack in the belts (e.g. clothes pegs, clips, etc.): a seat belt which is worn too
loosely may cause injury in the event of an accident.
Never wear the shoulder strap under your arm or behind your back.
Never use the same belt for more than one person and never hold a baby or child on your lap with your seat belt around
them.
The belt should never be twisted.
Following an accident, have the seat belts checked and replaced if necessary. Always replace your seat belts as soon as
they show any signs of wear.
When repositioning the rear bench seat, make sure that the seat belt is correctly positioned so that it can be used properly.
Make sure that the buckle is inserted into the appropriate catch.
Ensure that no objects are placed in the area around the seat belt catch as they could prevent it from being properly se-
cured.
1.21
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/4)
Depending on the vehicle, they are
composed of: Have the entire restraint
3 system checked following
seat belt inertia reel pretension- an accident.
ers1;
No operation whatso-
lap belt pretensioner 2; ever is permitted on any part of
air bags for driver and front pas- the system (pretensioners, air
senger3. bags, computers, wiring) and the
system components must not
These systems are designed to act in- be reused on any other vehicle,
dependently or together when the vehi- even if identical.
cle is subjected to a frontal impact. 2
To avoid incorrect triggering of
The following systems will be triggered the system which may cause
according to the level of impact force: injury, only qualified personnel
1
seat belt locking; from an approved dealer may
work on the pretensioner and air
the seat belt inertia reel pretensioner Pretensioners bag system.
(which engages to correct seat belt
slack); The pretensioners flatten the belt The ignition module electrical
against the body, holding the occupant specifications may only be tested
the lap seat belt pretensioners to against the seat, thus improving the ef- by a specially trained technician
hold the occupant in his seat; ficiency of the belt. using special equipment.
the front air bag. In the event of a severe frontal impact When the vehicle is scrapped,
and if the ignition is switched on, the contact an approved dealer for
system may engage the following de- disposal of the pretensioner and
pending on the force of the impact: air bag gas generators.
the seat belt inertia reel preten-
sioner1 which instantly retracts the
seat belt;
the lap belt pretensioner2 which in-
stantly retracts the lap belt.
1.22
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/4)
Force limiter Air bags for driver and front
Above a certain level of impact force, passenger
this mechanism is used to limit the force An airbag marking on the steer-
of the belt against the chest so that it is ing wheel and the dashboard (airbag
at an acceptable level. area A) indicates that this device is A
fitted.
Each air bag system consists of:
an air bag and gas generator fitted
on the steering wheel for the driver
and in the dashboard for the front
passenger;
an intelligent computer for both sys-
tems, which includes an impact
sensor and a monitor controlling the
electrical trigger system for the gas
generator;
1.23
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/4)
1.24
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (4/4)
All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent
the risk of serious injuries caused by items which may be dislodged when the air bag inflates.
1.25
Methods of restraint in addition to the rear seat belts
Force limiter
Above a certain level of impact force,
this mechanism is used to limit the force
of the belt against the chest so that it is
at an acceptable level.
1.26
Side protection devices
Side air bags
This air bag is fitted to each of the front
seats and is inflated at the sides of
the seats (door side) to protect the oc-
cupants in the event of a severe side
impact.
1.27
Additional methods of restraint
All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent
the risk of serious injuries caused by items which may be dislodged when the air bag inflates.
The air bag is designed to complement the action of the seat belt. Both the air bags and seat belts are integral parts of
the same protection system. It is therefore essential to wear your seat belt at all times. If seat belts are not worn, the
occupants of the vehicle are at risk of serious injury in the event of an accident. The risk of minor superficial injuries oc-
curring when the air bag is deployed may also increase, although such minor injuries are always possible with air bags.
If the vehicle should overturn or suffer a rear impact, however severe, the pretensioners and air bags are not always triggered.
Impacts to the underside of the vehicle, e.g. from pavements, potholes or stones, can all trigger these systems.
No work or modification whatsoever may be carried out on any part of the air bag system (air bags, pretensioners, compu-
ter, wiring harness, etc.), except by qualified personnel from an approved Dealer.
To ensure that the system is in good working order and to avoid accidental triggering of the system which may cause injury,
only qualified Network personnel may work on the air bag system.
As a safety precaution, have the air bag system checked if your vehicle has been involved in an accident, or is stolen or
broken into.
When selling or lending the vehicle, inform the user of these points and hand over this handbook with the vehicle.
When scrapping your vehicle, contact your approved Dealer for disposal of the gas generator(s).
1.28
Child safety: General information (1/2)
Carrying children
Children, and adults, must be correctly
seated and strapped in for all journeys.
The children being carried in your vehi-
cle are your responsibility.
A child is not a miniature adult. Children
are at risk of specific injuries as their
muscles and bones have not yet fin- Drivers responsibility
ished growing. The seat belt alone when parking or stopping
would not provide suitable protection. the vehicle
Use an approved child seat and ensure
Never leave an animal,
you use it correctly.
child or adult who is not self-suffi-
cient alone on your vehicle, even for
a short time.
They may pose a risk to themselves
or to others by starting the engine,
A collision at 30 mph activating equipment such as the
(50km/h) is the same as fall- electric windows or by locking the
ing a distance of 10metres. doors.
Transporting a child without Also, in hot and/or sunny weather,
a restraint is the equivalent of allow- please remember that the tempera-
ing him or her to play on a fourth- ture inside the passenger compart-
floor balcony without railings. ment increases very quickly.
Never travel with a child held in your
arms. In the event of an accident, RISK OF DEATH OR SERIOUS
you will not be able to keep hold of INJURY.
To prevent the doors being the child, even if you yourself are
opened, use the Child wearing a seat belt.
safety device (refer to the If your vehicle has been involved in
information on Opening a road accident, replace the child
and closing the doors in Section1). seat and have the seat belts and
ISOFIX anchorage points checked.
1.29
Child safety: General information (2/2)
Using a child seat
The level of protection offered by the Set a good example by always fas-
child seat depends on its ability to re- tening your seat belt and teaching
strain your child and on its installation. your child:
Incorrect installation compromises the to strap themselves in correctly;
protection it offers the child in the event to always get in and out of the car
of harsh braking or an impact. at the kerb, away from busy traf-
fic.
Before purchasing a child seat, check
that it complies with the regulations for Do not use a second-hand child
the country you are in and that it can seat or one without an instruction
be fitted in your vehicle. Consult an ap- manual.
proved dealer to find out which seats Check that there are no objects in
are recommended for your vehicle. the vicinity of the child seat which
Before fitting a child seat, read the could impede its operation.
manual and respect its instructions. If
you experience any difficulties during
Never leave a child unat-
installation, contact the manufacturer
tended in the vehicle.
of the equipment. Keep the instructions
with the seat. Check that your child is
always strapped in and that
the belt or safety harness used is
correctly set and adjusted. Avoid
wearing bulky clothing which could
cause the belts to slacken.
Never let your child put their head or
arms out of the window.
Check that the child is in the correct
position for the entire journey, espe-
cially if asleep.
1.30
Child safety: choosing a child seat
1.31
child safety: choosing a child/baby seat mounting (1/2)
There are two ways of attaching child Attachment using the ISOFIX
seats: via the seat belt or using the system
ISOFIX system. Authorised ISOFIX child seats are ap-
Attachment via the seat belt proved in accordance with regulation
ECE-R44 in one of the three following
The seat belt must be adjusted to scenarios:
ensure that it is effective in the event of universal ISOFIX 3-point forward-
harsh braking or an impact. Do not use the child seat
facing seat;
if it may unfasten the seat
Ensure that the strap paths indicated semi-universal ISOFIX 2-point seat;
belt restraining it: the base
by the child seat manufacturer are re- specific.
of the seat must not rest on
spected. the buckle and/or catch of the seat For the latter two, check that your child
Always check that the seat belt is cor- belt. seat can be installed by consulting the
rectly fastened by pulling it up, then list of compatible vehicles.
pulling it out fully whilst pressing on the Attach the child seat with the ISOFIX
child seat. locks, if these are provided. The ISOFIX
Check that the seat is correctly held by system allows quick, easy, safe fitting.
moving it from side to side and back The seat belt must never The ISOFIX system consists of 2 rings
to front: the seat should remain firmly be twisted or the tension and, in some cases, a third ring.
fixed. relieved. Never pass the
Check that the child seat has not been shoulder strap under the
installed at an angle and that it is not arm or behind the back.
resting against a window. Check that the seat belt has not
been damaged by sharp edges.
If the seat belt does not operate nor- Before using an ISOFIX
mally, it will not protect the child. child seat that you pur-
Consult an approved dealer. Do not chased for another vehicle,
use this seat until the seat belt has check that its installation is
No modifications may be been repaired. authorised. Consult the list of ve-
made to the component hicles which can be fitted with the
parts of the restraint system seat from the equipment manufac-
(ISOFIX seat belts, seats turer.
and their mountings) originally fitted.
1.32
child safety: choosing a child/baby seat mounting (2/2)
Fit the hook of the strap onto ring3 and
pull the strap so that the seatback of the
child seat comes into contact with the
top of the seatback on the vehicle seat.
1
4
3
The two rings1 are located between The third ring is used to attach the
the seatback and the seat base (behind upper strap on some child seats.
a cover) and are identified by a mark- To access it, pass the belt on the child
ing. seat behind the rear bench seatback,
To ensure your child seat can be easily then open flap4.
fitted and locked on rings1, use access
guides2 on the child seat.
1.33
child safety: fitting a child seat (1/3)
Some seats are not suitable for fitting In the front seat In the rear side seat
child seats. The diagram on the follow- The laws concerning children travel- A carrycot can be installed across the
ing page shows you how to attach a ling in the front passenger seat differ in vehicle and will take up at least two
child seat. every country. Consult the legislation in seats. Position the child with his or her
The types of child seats indicated may force and follow the indications on the feet nearest the door.
not be available. Before using a differ- diagram on the following page. Before Move the front seat as far forward as
ent child seat, check with the manufac- fitting a child seat in this seat (if author- possible to install a rear-facing child
turer that it can be fitted. ised): seat, then move back the seat or seats
disconnect the air bag (refer to infor- in front in accordance with the child
mation on the following pages); seat instructions.
lower the seat belt as far as possible;
move the seat back as far as possi- For the safety of the child in the for-
ble and tilt the seatback backwards ward-facing seat, do not move the seat
slightly (at an angle of 25 approxi- in front back past the middle of the
Fit the child seat in a rear mately); runner, do not tilt the seatback too far
seat wherever possible. on equipped vehicles, raise the seat (maximum of 25 ) and raise the seat as
Check that when installing base as far as possible. much as possible.
the child seat in the vehicle Do not change these settings after the Check that the forward-facing child seat
it is not at risk of coming loose from child seat is installed. is resting against the back of the vehi-
its base. cle seat and that the headrest of the ve-
If you have to remove the headrest, hicle is not obstructing its use.
check that it is correctly stored so
that it does not come loose under Rear centre seat
harsh braking or impact. RISK OF DEATH OR Check that the belt is suitable for se-
Always attach the child seat to the SERIOUS INJURY: before curing your child seat. Consult an ap-
vehicle even if it is not in use so that fitting a rear-facing child proved Dealer.
it does not come loose under harsh seat to this seat, check
braking or impact. that the air bag has been deacti-
vated (refer to the information on
Child safety: deactivating/activat-
ing the front passenger air bag in
Section1).
1.34
child safety: fitting a child seat (2/3)
Child seat attached using the ISOFIX
mounting
seat which allows an ISOFIX child
seat to be fitted.
the rear seats are fitted with an
anchorage point which allows a for-
ward-facing ISOFIX child seat with uni-
versal approval to be fitted. The an-
chorage points are located under the
carpet in the luggage compartment,
behind the bench seat.
The size of the ISOFIX child seat is in-
dicated by a letter:
A, B and B1: for forward-facing seats
Child seat installation Child seat attached using the belt in group 1 (9 to 18 kg);
diagram Seat which allows a standard-
C: rear-facing seats in group 1 (9 to
seats.
Seat not suitable for fitting child
facing standardised Universal seat to
be installed using a seat belt.
F and G: carrycots in group 0 (less
than 10 kg).
1.35
child safety: fitting a child seat (3/3)
The table below summarises the information already shown on the diagram on the previous page, to ensure the regu-
lations in force are respected.
(5) RISK OF DEATH OR SERIOUS INJURY: before fitting a rear-facing child seat in the front passenger seat, check
that the air bag has been deactivated (refer to the information on Child safety: deactivating/activating the front pas-
senger air bag at the end of the paragraph).
1.36
Child safety: deactivating/activating the front passenger air bag (1/3)
DANGER
1 Since operation of the front
passenger air bag is not
compatible with the position
2 of a rear-facing child seat, NEVER
fit a rear-facing child seat on a front
passenger seat with an active front
air bag. The child may suffer very
serious injuries if the air bag is trig-
gered.
1.37
Child safety: deactivating/activating the front passenger air bag (2/3)
1.38
Child safety: deactivating/activating the front passenger air bag (3/3)
It is forbidden to fit a rear-facing child
seat to the front passenger seat if the
air bag activation/deactivation system
is faulty.
1 Allowing any other passenger to sit in
that seat is not recommended.
1.39
Driving position: left-hand drive (1/2)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
29 28 27 26 25 24 17 16 15
23 18
22
19
21
20
1.40
Driving position: left-hand drive (2/2)
The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY.
1.41
Driving position: right-hand drive (1/2)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
20 19
29 28 18 17 16 15
21
27
22
26
23
25
24
1.42
Driving position: right-hand drive (2/2)
The fittings described below DEPEND ON THE VEHICLE EQUIPMENT AND COUNTRY.
1.43
Warning lights (1/4)
The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY.
1
Heating passenger seat op-
erating warning light
This indicates that the front passen-
Antipollution, fuel economy and driv-
ing in Section 2.
1.44
Warning lights (2/4)
The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY.
STOP light
This lights up when the ignition
Battery charge warning light
If the light comes on accompa-
is switched on and goes out as soon as nied by the warning light, this in-
the engine is started. It comes on with dicates that the electrical circuit is over-
other warning lights and/or messages, charged or undercharged.
A and is accompanied by a beep.
It requires you to stop immediately, for
your own safety, as soon as traffic con-
Oil pressure warning light
If it comes on when you are
ditions allow. Switch off the engine and driving accompanied by the
do not restart it. warning light and a beep, it is essential
to stop and switch off the ignition.
Contact an approved Dealer.
Check the oil level (refer to the informa-
D
ing light
Electronic parking brake
and brake circuit fault warn-
tion on the Engine oil level in Section
4). If the level is normal, the light has
come on for another reason: contact an
Warning light If it lights up while braking, accompa- authorised dealer.
This lights up when the ignition nied by the warning light, this in-
is switched on and goes out as soon as dicates a low level in one of the circuits
the engine is started. It can light up in or a fault in the braking system.
conjunction with other indicator lights Stop as soon as traffic conditions allow
and/or messages on the instrument and contact an authorised dealer.
panel.
It means you should drive very care-
fully to an authorised dealer as soon
as possible. If you fail to follow this rec-
ommendation, you risk damaging your
vehicle.
1.45
Warning lights (3/4)
The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY.
1.46
Warning lights (4/4)
The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY.
1.47
Instrument panel: displays and indicators (1/2)
Coolant temperature indicator
1.48
Instrument panel: displays and indicators (2/2)
7
8
1.49
Trip computer and warning system (1/10)
c) mileage before service;
d) programmed speed (speed limiter/
2 cruise control);
1 e) trip log, operating faults and informa-
tion message readout.
1.50
Trip computer and warning system (2/10)
Interpreting some of the Automatic resetting of the
values displayed after journey parameters
2 resetting Resetting occurs automatically when
The values showing average fuel con- the maximum value of any of the pa-
sumption, range and average speed rameters is exceeded.
will become more stable and reliable
the further you travel after pressing the
reset button.
For the first few miles after pressing
the reset key you will notice that the
3 range increases as you travel. This
range takes into account the average
fuel consumption since the last time the
reset button was pressed. Therefore,
the average fuel consumption may de-
Trip mileage resetting crease when:
With trip mileage recorder selected on the vehicle is no longer accelerating;
the display, press button2 or3 until the
mileage recorder resets to zero. the engine reaches its operating
temperature (if the engine was cold
when reset key was pressed);
Resetting the journey when driving from an urban area
parameters (reset button) onto the open road.
With one of the journey parameters se-
lected on the display, press button2
or3 until the display resets.
1.51
Trip computer and warning system (3/10)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
b) Journey parameters.
Fuel used since the last reset.
1.52
Trip computer and warning system (4/10)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
1.53
Trip computer and warning system (5/10)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
Note: depending on the vehicle, the mileage before a service changes according to driving style (frequent driving at low speeds,
door-to-door journeys, extensive use at idle speed, towing, etc.). The distance remaining until the next service can therefore de-
crease more quickly in some cases than the actual distance travelled.
Resetting the display after the service in accordance with the maintenance schedule.
The mileage before service must only be reset after a service which complies with the recommendations in the Maintenance
Service Booklet. If you decide to change the oil more frequently, do not reset this data each time the oil is changed to avoid ex-
ceeding the replacement intervals for other parts in the maintenance schedule.
To reset the distance before service, press and hold one of the display reset buttons for approximately 10 seconds until the dis-
play shows the mileage permanently.
1.54
Trip computer and warning system (6/10)
Journey parameters
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
g) Computer log.
Successive display:
of information messages (low card battery, etc.);
operating fault messages (check the injection system, etc.).
1.55
Trip computer and warning system (7/10)
Information messages
These can help either in the vehicle starting phase, or give information about a selection or a driving status. Examples of
information messages are given in the following pages.
The card battery charge is too low (refer to the information on the Renault card:
Card battery low
battery in section 5).
Indicates the presence of water in the diesel filter; contact your authorised dealer
Clean diesel filter
as soon as possible.
To stop the engine when no card has been recognised, press and hold the engine
No card - press and hold
start/stop button.
Disengage clutch + start To start, depress the clutch pedal then press the engine start/stop button.
1.56
Trip computer and warning system (8/10)
Operating fault messages
These appear with the warning light and mean that you should drive very carefully to an authorised dealer as
soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle.
They disappear when the display selection key is pressed or after several seconds and are stored in the computer log. The
warning light stays on. Examples of operating fault messages are given in the following pages.
Indicates a fault in one of the pedal sensors, battery management system or oil
Check vehicle
level sensor.
Check emission control Indicates a fault in the vehicles particle filter system.
Check 4WD Indicates a fault in the vehicles all-wheel drive (4WD) transmission system.
Check air bag Indicates a fault in the air bag system (air bag, pretensioners, etc.).
1.57
Trip computer and warning system (9/10)
Warning messages
These appear with the warning light and require you to stop immediately, for your own safety, as soon as traffic
conditions allow. Stop your engine and do not restart it. Contact an approved Dealer.
Examples of warning messages are given in the following pages. Note: the messages appear on the display either individually
or alternately (when there are several messages to be displayed), and may be accompanied by a warning light and/or a beep.
Battery recharging fault Indicates a fault with the vehicles battery charging circuit.
1.58
Trip computer and warning system (10/10)
Warning messages
These appear with the warning light and require you to stop immediately, for your own safety, as soon as traffic
conditions allow. Stop your engine and do not restart it. Contact an approved Dealer.
Examples of warning messages are given in the following pages. Note: the messages appear on the display either individually
or alternately (when there are several messages to be displayed), and may be accompanied by a warning light and/or a beep.
Indicates an electronic parking brake fault. Apply the electronic parking brake
Immobilise the vehicle
manually and ensure that the vehicle is immobilised using a chock.
Major under-inflation Indicates major under-inflation of the tyre shown on the display.
1.59
Clock and external temperature
External temperature
1
indicator
Special note:
When the outside temperature is 3C
to +3C, the C characters flash (signal-
ling a risk of black ice on the road).
Note: in some cases (vehicle stopped
for less than 3 hrs 30 mins), the infor-
mation displayed on the screen when
the ignition is switched on may be in-
correct.
Resetting clock1
Refer to the specific equipment instruc-
tions (navigation system, radio) for the
particular features.
External temperature
indicator
As ice formation is related
to climatic exposure, local
If the power supply is cut (battery air humidity and temperature, the
disconnected, supply wire cut, etc.), external temperature alone is not
the clock must be reset. sufficient to detect ice.
We recommend that you do not
adjust these settings while driving.
1.60
Steering wheel/power-assisted steering
Variable power-assisted Operating faults
steering If the message Check steering is
It is equipped with a system which displayed on the instrument panel
adapts the level of assistance to the ve- accompanied by the warning
hicle speed. light, consult an authorised dealer
straight away.
Steering is made easier during parking
manoeuvres (for added comfort) whilst If the message "Steering fault" is dis-
the force needed to steer increases played on the instrument panel and
progressively as the speed rises (for the warning light comes on,
1 enhanced safety at high speeds). stop the vehicle as soon as possible
and contact an authorised dealer.
1.61
Rear view mirrors
Folding door mirrors
With the engine running, move
A button1 to positionF: the door mirrors
B fold away.
To reset them for driving, return to posi-
tionC,D orE.
D
C E
Heated door mirrors
F Mirror de-icing is carried out at the
1
same time as rear screen de-icing.
2
1.62
AUDIBLE AND VISUAL SIGNALS
Direction indicators 2
Move stalk 1 parallel to the steering
wheel and in the direction you are going
to turn it.
1 When driving on the motorway, the
steering wheel is not often turned
0 enough to return the stalk automatically
A to0. There is an intermediate position
in which the switch may be held when
changing lanes.
When the stalk is released, it automati-
cally returns to0.
Horn
Press steering wheel bossA.
Hazard warning lights
Press switch2. This switch il-
luminates all four direction indicators
and the side-mounted indicator lights
Headlight flasher simultaneously. It must only be used in
Pull stalk 1 towards you to flash the an emergency to warn drivers of other
headlights. vehicles that you have had to stop in
an area where stopping is prohibited or
unexpected or that you are obliged to
drive under special conditions.
Depending on the vehicle, the hazard
warning lights may come on auto-
matically under heavy deceleration.
You can switch them off by pressing
switch2 twice.
1.63
Exterior lighting and signals (1/3)
1
Main beam headlights
With the dipped beam head-
lights lit, push stalk 1 forwards. This
1 indicator light on the instrument panel
comes on.
To return to the dipped headlight posi-
tion, pull the stalk1 towards you again.
If the headlights are off, you can pull
stalk1 towards you to flash the head-
lights. The headlights go off as soon as
3 2 4 the stalk is released.
Side lights
Turn the ring3 until the symbol k Dipped beam
headlights
is opposite mark2.
The instrument panel will light up. The Manual operation
brightness can be adjusted by turning Turn the ring3 until the symbol is oppo-
the control knob4. This control can also site mark2. This indicator light on the
be used to adjust the brightness of the instrument panel comes on. Before driving at night:
audio equipment and air conditioning check the electrical equip-
Automatic operation ment is operating correctly
display.
(depending on vehicle) and adjust your headlights
Turn ring3 until the AUTO symbol is op- (if your vehicle is not carrying its
posite mark2: with the engine running, normal load). As a general precau-
the dipped beam headlights switch on tion, check that the lights are not
or off automatically depending on the obscured (by dirt, mud, snow or ob-
brightness of the light outside, without jects being transported).
any action on stalk1.
1.64
Exterior lighting and signals (2/3)
Switching off the lights See-me-home lighting
There are two possibilities: function
1 manually, move ring3 to the OFF po- This function (useful, for example, for
sition; opening a gate, garage, etc.) enables
you to switch the dipped headlights on
automatically, the lights are switched momentarily.
off when the engine is switched off
or when the drivers door is opened. With the engine and lights off and
In this case, the next time the engine ring3 in the OFF position, pull stalk1
is started the lights will be switched towards you: the dipped beam head-
back on according to the position of lights light up for approximately thirty
3 2 the ring3. seconds.
This action may be carried out no more
Lights-on warning buzzer than ten times for a maximum lighting
period of ten minutes.
If the lights are on after the engine is
Cornering lights switched off, a warning beep sounds To switch off the lights before they go
when the drivers door is opened to out automatically, turn the ring on the
Depending on the vehicle, if the dipped
warn you that the lights are still on. stalk1, then return it to the OFF posi-
beam headlights are on when corner-
tion.
ing, and under certain driving condi-
tions (speed, steering wheel angle,
etc.), additional lights are switched on
to light the inside of the bend.
1.65
Exterior lighting and signals (3/3)
1.66
Electric beam height adjustment
0
A
1
On equipped vehicles, controlA allows
you to adjust the height of the beams
according to the load.
Turn controlA downwards to lower the
headlights and upwards to raise them. 1
For vehicles not fitted with controlA,
adjustment is automatic.
1.67
WINDSCREEN WASH/WIPE (1/2)
Vehicle fitted with front
windscreen wiper rain sensor
A Wiping on request
1 A 2 The stalk returns to positionB when
1
released.
B
B Off
C
C Automatic wiper function
D When this position is selected, the
E system detects water on the wind-
screen and triggers the wipers at a
suitable wiping speed.
It is possible to change the time be-
tween sweeps by turning ring2.
D Normal wiping speed
With the ignition on, move stalk1. Special note
E Fast wiping speed
A Wiping on request When driving, every time the vehicle
The stalk returns to positionB when stops the fast wiping speed is reduced
released. to normal wiping speed.
B Off As soon as the vehicle moves off,
C Intermittent wiping wiping will return to the speed originally
The wipers will pause for several selected.
seconds between sweeps. It is pos- If stalk1 is operated, it overrides and
sible to change the time between cancels the automatic function.
sweeps by turning ring2.
D Normal wiping speed When working in the engine
E Fast wiping speed compartment, ensure that
the windscreen wiper stalk
is in positionB (off).
Risk of injury.
1.68
WINDSCREEN WASH/WIPE (2/2)
Headlights on
The headlight washers will be activated
at the same time.
1 A
1
B
C
D
E
In freezing or snowy weather, ensure
they are not stuck to the windscreen
(including the central area located
behind the interior rear-view mirror)
and the rear screen before starting
the wipers (risk of motor overheat-
Windscreen washer, ing).
headlight washers
(depending on vehicle) Check the condition of the wiper
blades. You are responsible for their If you switch off the ignition before
With the ignition on, pull stalk1 to- service life: switching off the windscreen wiper
wards you, then release. they must remain clean: clean (positionA) the blades will stop at
the blades, windscreen and random on the windscreen.
Headlights off rear screen regularly with soapy
One short pull activates the windscreen water;
washers and one sweep of the wind- do not use them when the wind-
screen wipers. screen or rear screen are dry;
Before any action involving
free them from the windscreen or
A longer pull activates the windscreen the windscreen (washing
rear screen when they have not
washers and four sweeps of the wind- the vehicle, de-icing, clean-
been used for a long time.
screen wipers followed by one sweep a ing the windscreen, etc.)
In all cases, replace them as soon
few seconds later. return stalk1 to positionB (park).
as they begin to lose efficiency: ap-
proximately once a year. Risk of injury and/or damage.
1.69
REAR screen wash/wipe
Rear screen wash/wipe
To use this, push stalk1.
1 2 A longer pull activates the windscreen
1 A
washers and four sweeps of the wind-
screen wipers followed by one sweep a
B
few seconds later.
C
Special note D
E
If the windscreen wipers are opera-
tional when you select reverse gear, the
rear screen is wiped intermittently.
1.70
FUEL TANK (1/3)
Diesel versions
It is essential to use diesel fuel that
conforms with the information given on
A the label inside coverA.
Petrol versions
It is essential to use unleaded petrol.
The octane rating (RON) must conform
with the information given on the label
on coverA. Refer to the information on
Engine specifications in Section 6.
B
1
Capacity of the fuel tank: 65 liters Fuel grade
(approximately).
Use a high-grade fuel that complies
Pull lever 1, located under the dash- with the legislation in force in each
board on the drivers side to release the country and which must conform to
coverA. Open it then unscrew fuel filler the specifications given on the label
capB. on coverA. Refer to the information on
Engine specifications in Section 6. Fuel filler cap: this is of a
For details on filling the fuel tank, refer special type. If you have
to the information on Filling up with to replace it, make sure
fuel. the new cap is of the same
type.
Contact your approved Dealer.
Never place the cap near a source
of heat or flame.
1.71
Fuel tank (2/3)
Vehicles running on ethanol-based Filling with fuel
fuel Persistent smell of
Insert the nozzle fully before beginning fuel
It is essential to use unleaded petrol or to fill the tank (risk of splashback).
fuel containing a maximum of 85% eth- If you notice a persistent
anol (E85). Keep the nozzle in this position smell of fuel you should:
throughout the entire filling operation.
In very cold conditions, it may be very When the pump cuts out automatically stop the vehicle if traffic condi-
difficult or even impossible to start the at the end of the filling procedure, a tions allow and switch off the igni-
engine. To avoid this problem, use un- maximum of two further filling attempts tion;
leaded petrol or, on equipped vehicles, may be made, as there must be suffi- switch on the hazard warning
use the heater integrated in the engine: cient space in the fuel tank to allow for lights and ask your passengers
connect the special end of the exten- expansion. to leave the vehicle and to keep
sion piece supplied into the socket in- away from traffic;
tegrated into the radiator grille and the Make sure that no water enters the fuel
other end into a 220V socket for at least tank during filling. The cap and its sur- contact an authorised dealer.
6 hours before starting. round must remain clean.
1.72
Fuel tank (3/3)
The engine can then be restarted; if it
still does not run properly, allow it to run
at idle. If the engine does not start after
several attempts, contact an authorised
dealer.
No modifications what-
soever are permitted on
any part of the fuel supply
system (electronic unit,
Running out of fuel on diesel wiring, fuel circuit, injector, protec-
versions tive covers, etc.) as this may be
After a breakdown caused by com- dangerous (unless undertaken by
pletely running out of fuel, the system qualified Network personnel).
must be reprimed before the engine is
restarted:
Open the bonnet;
operate priming bulb2 several times
and stop when you can feel the pres-
sure.
The engine may be hot
during operations in close
proximity. In addition, the
engine cooling fan may
start at any moment.
Risk of injury.
1.73
1.74
Section 2: Driving
(Advice on use relating to fuel economy and the environment)
2.2
STARTING THE ENGINE (1/2)
Starting a vehicle with an automatic
gearbox
Lever in position P.
A For all vehicles:
if one of the starting conditions is not
met, the message depress brake +
start or depress clutch + start or
1 3 shift to P is displayed on the instru-
ment panelA.
In some cases it will be necessary
to move the steering wheel while
2 pressing start button 1 to assist in
unlocking the steering column; the
message turn steering wheel +
Starting the engine Hands-free RENAULT card: start warns of this.
The RENAULT card must be inserted
Remote control RENAULT card Starting with the boot open (in
in card reader2 or in detection zone3.
hands-free mode)
When you get into the vehicle, insert the To start, depress the brake or clutch
RENAULT card fully into card reader2. It is only possible to start the engine if
pedal and press button 1. If a gear
the card is in the reader2.
To start, press button1. If a gear is en- is engaged, the vehicle may only be
gaged, depress the clutch pedal to start started by depressing the clutch pedal.
the vehicle.
2.3
STARTING THE ENGINE (2/2)
Operating faults
In certain cases, the hands-free
RENAULT card may not work:
A when the RENAULT card battery is
drained, flat battery, etc.
near to appliances operating on the
same frequency as the card (moni-
tor, mobile phone, video game, etc.);
1
if the vehicle is located in a zone of
high electromagnetic radiation. Drivers responsibility
The message insert card appears on Never leave your vehicle
2 the instrument panelA. with the RENAULT card
Insert the RENAULT card fully into card inside and never leave a
reader2. child (or a pet) unsupervised, even
Accessories function for a short while.
(Switching on the ignition)
There is a risk that they could start
To switch on certain functions with the the engine or operate electrical
engine off (radio, navigation system, equipment (electric windows etc.)
etc.), press button1 without depressing and trap part of their body (neck,
the pedals. arms, hands, etc.).
Note: these can be switched off by Risk of serious injury.
pressing button1 twice. Never switch off the ignition before
the vehicle has come to a complete
stop. Switching off the engine dis-
ables the assistance equipment:
brakes, steering, etc., and passive
safety equipment such as airbags
and pretensioners.
2.4
STOPPING THE ENGINE
Special note
If the card is no longer in the reader
when you try to switch the engine off,
A the message No keycard - Press When leaving your vehi-
and hold appears on the instrument cle, in particular with the
panel A: press button 1 for over two RENAULT card, check that
seconds. the engine has completely
stopped.
Hands-free RENAULT card:
1
With the card in the vehicle, press
button1: the engine will stop. The steer-
ing column is locked when the drivers Never leave your vehicle
door is opened or the vehicle is locked. with the RENAULT card
2 inside and never leave a
If the card is no longer in the passenger child (or a pet) unsuper-
Conditions for stopping the compartment when you try to switch the vised, even for a short while.
engine off, the message No keycard
engine Press and hold appears on the instru- There is a risk that they could start
The vehicle must be stationary, with the ment panel: press button1 for over two the engine or operate electrical
lever positioned in N or P for vehicles seconds. equipment (electric windows etc.)
with an automatic transmission. and trap part of their body (neck,
With the engine switched off, any ac- arms, hands, etc.).
cessories being used (radio, etc.) will Risk of serious injury.
Remote control RENAULT continue to function for approximately
10 minutes. Never switch off the ignition before
card the vehicle has come to a complete
With the card in reader 2, press When the drivers door is opened, the stop. Switching off the engine dis-
button1:the engine will stop. Removing accessories stop working. ables the assistance equipment:
the card from the reader locks the steer- brakes, steering, etc., and passive
ing column. safety equipment such as airbags
and pretensioners.
2.5
Special features of petrol versions
The following operating conditions If you notice any of the above operating
should be avoided: faults, have the necessary repairs car-
driving for long periods when the low ried out as soon as possible by an ap-
fuel level warning light is lit up, proved dealer.
2.6
SPECIAL FEATURES OF DIESEL VERSIONS
Diesel engine speed Precautions to be taken in winter
Diesel engines are fitted with injection To avoid faults in icy weather:
equipment which prevents the engine ensure that the battery is always fully
speed being exceeded irrespective of charged;
the gear selected.
always keep the diesel tank rela-
Running out of fuel tively full to avoid water vapour con-
You may start the engine normally after densing in it and accumulating at the
refilling the fuel tank even if you have bottom of the tank.
completely run out of fuel, provided
that the battery is fully charged.
However, if the engine fails to start after
a few seconds and several attempts,
contact an approved Dealer.
2.7
Special features of diesel versions fitted with a particle filter
Diesel engine speed Precautions to be taken in
Depending on the vehicle, the
warning light lights up on the instrument
Diesel engines are fitted with injection
equipment which prevents the engine
winter
To avoid faults in icy weather:
panel to show that there is a risk of the speed being exceeded irrespective of
particle filter becoming clogged. the gear selected. ensure that the battery is always fully
charged,
To clean the particle filter, for 60 miles If the message Check emission con-
(100 km) after the warning light comes trol is displayed on the instrument always keep the diesel tank rela-
on drive at an average speed of at least
42 mph (70 kph), where traffic condi-
tions and the speed limit will allow, until
panel accompanied by the and
warning lights. Consult an au-
tively full to prevent water vapour
condensing in it and accumulating at
the bottom of the tank.
the warning light goes out. thorised dealer straight away.
You may need to restart the operation if When driving, depending on the fuel
the vehicle has to stop before the warn- grade used, it is possible that white
ing light goes out. smoke may be emitted.
As an example, in this case, the clean- This is due to the exhaust particle filter
ing operation lasts for up to 20 minutes. being cleaned automatically, and does
not affect the way the vehicle runs.
2.8
GEAR LEVER/HANDBRAKE
Handbrake
1 To release
Pull lever4 upwards, press button3
3 and then lower the lever to the floor.
To apply
Pull upwards, check that the vehicle is
properly immobilised.
2
4
2.9
ELECTRONIC PARKING BRAKE (1/4)
Automatic releasing of the
Indicator lights3 and } go out a
few seconds after the engine has been
electronic parking brake
The brake will be released as soon as
switched off. the vehicle starts and accelerates.
1
Note: if the drivers door is opened, in-
dicator lights3 and } will light up
again. They will go out when the door
Manual operation
Applying the parking brake
is closed. Pull then release the switch2. The
2 Warning: if one of the doors is open
but the parking brake has not been ap- } indicator light lights up on the
instrument panel accompanied by the
plied, a bleep sounds and the message
apply parking brake is displayed on message parking brake applied and
3 the instrument panel. the3 indicator light.
In this case, the vehicle must be im- Releasing the parking brake
Automatic operation mobilised by pulling then releasing the With the ignition on and while depress-
The electronic parking brake ensures switch2. ing the brake pedal, press switch2
automatic vehicle immobilisation when The parking brake is released as soon until indicator lights3 on the switch2
the engine is stopped by pressing
the engine start/stop button 1.
as the vehicle is driven.
and
out.
} on the instrument panel go
For certain country-specific model ver-
sions, the automatic brake application Dynamic braking
function is not activated. Refer to the in- In an emergency, under exceptional
formation on Manual operation. circumstances, switch2 can be pulled
Before leaving the vehicle,
To confirm that the electronic parking check that the electronic to stop the vehicle. Beyond a threshold,
brake is applied, the message parking
brake applied and indicator light }
parking brake is fully ap-
plied. the } and indicator lights
come on. Consult an approved Dealer.
on the instrument panel and indicator
light3 on switch2 light up.
The } indicator light lights up
on the instrument panel accompa-
nied by the message parking brake
applied.
2.10
ELECTRONIC PARKING BRAKE (2/4)
Parking without applying the Brief stop
parking brake To manually activate the electronic
(if there is a risk of ice etc.): parking brake, (when stopping at a red
Stop the engine by pressing the light, or stopping when the engine is
engine on/off button1; running, etc.): pull and release switch2.
1 The brake is released as soon as the
engage a gear (on vehicles with vehicle is started up again.
manual gearboxes) or shift the gear
lever into position P (on vehicles with
automatic transmissions);
simultaneously depress the brake
2 pedal and press switch2 until the in-
dicator light3 goes out.
3 When the drivers door is opened, a
warning message will be displayed and
a beep sounds for around 5 seconds to
Special cases indicate that the parking brake has not
When the vehicle is on an incline or been applied.
when towing a trailer, pull handle2 for
Note: it is still possible to release the
approximately 3 seconds to fully apply
parking brake as long as no door is
the parking brake.
opened or closed and the vehicle is not
Note: if the vehicle is not immobilised locked.
despite fully applying the parking brake,
due to the steepness of the incline, the
message immobilise the vehicle is
displayed on the instrument panel. The
vehicle must be parked elsewhere.
2.11
ELECTRONIC PARKING BRAKE (3/4)
Versions with an automatic Operating faults
gearbox When indicator lights and in cer- Indicator light } flashes, accom-
panied by indicator lights and
For safety reasons, automatic release
is deactivated when the drivers door tain cases } light up on the instru-
ment panel accompanied by the mes-
and the message parking
brake fault: this indicates that it is es-
is open or not shut properly and the
engine is running (in order to prevent sage check parking brake, contact an sential to stop immediately (as soon as
the vehicle from moving without the approved dealer urgently. traffic conditions allow). Contact an ap-
driver). The release manually mes- proved Dealer.
sage appears on the instrument panel
when the driver depresses the accel-
erator.
2.12
ELECTRONIC PARKING BRAKE (4/4)
4 7
4 A
5
A B C
2
6
5
Emergency unlocking The parking brake can be released. To
release manually: Indicator light comes on accom-
remove the luggage compartment panied by the message check park-
carpet and the emergency spare ing brake. With the ignition on, simul-
Before releasing the park- taneously depress the brake pedal and
ing brake manually, it is es- wheel cover;
insert wheelbrace4 into loop6 and, press switch2. If they do not go off, do
sential to immobilise the ve- not drive the vehicle and contact an ap-
hicle by engaging first gear for vehicles without amplifier7, press
on housing5; proved dealer.
(manual gearbox) or shifting to po-
sition P (automatic transmission). If pull (movementB) or push (move-
the slope requires it, chock the vehi- mentC) the top of wheelbrace4
cle. If it is not possible to immobilise until the parking brake is heard to re- Never leave a child (or
the vehicle, do not operate the lever lease. animal) alone in the vehi-
and contact an approved Dealer. This control cannot be used to reap- cle with the RENAULT card
A reminder can be found on the ply the parking brake. inside. They could acci-
label in areaA. dentally release the parking brake
which would enable the vehicle to
roll away.
2.13
Advice: antipollution, fuel economy and driving (1/3)
Your vehicle complies with criteria for Aiding fuel economy Have your vehicle adjusted and
recycling and recovering vehicles at the checked by an approved Dealer, in ac-
end of their service life which will come Depending on the vehicle, in order to cordance with the instructions given in
into force in 2015. optimise consumption, an indicator light your maintenance schedule: they will
on the instrument panel will inform you have all the equipment necessary for
Some parts of your vehicle have there- of the best moment to upshift or down-
fore been designed to facilitate future ensuring that your vehicle is maintained
shift gears: to its original standard.
recycling.
These parts are easy to remove so \ shift up a gear;
Engine adjustments
that they can be recovered and reproc-
essed by recycling companies. [ shift down a gear. ignition: this does not require ad-
justment.
By virtue of its design, moderate fuel
consumption and initial settings, your Maintenance spark plugs: for optimum fuel econ-
vehicle also conforms to current anti- omy, efficiency and performance
pollution regulations. The manufac- It is important to remember that failure to
respect antipollution regulations could the specifications laid down by our
turer is actively striving to reduce pol- Design Department must be strictly
lutant exhaust gas emissions and to lead to legal action being taken against
the vehicle owner. In addition, replacing applied.
save energy. But the fuel consumption
of your vehicle and the level of pollutant engine, fuel supply system and exhaust If the spark plugs have to be
exhaust gas emissions are also your components with parts other than those changed, use the make, type and
responsibility. Ensure that it is main- originally recommended by the manu- gap specified for your vehicles
tained and used correctly. facturer may alter your vehicle so that engine. Contact an approved dealer
it no longer complies with antipollution for this.
regulations.
idle: this does not require adjust-
ment.
air filter, diesel filter: a clogged ele-
ment reduces performance. It must
be replaced.
2.14
Advice: antipollution, fuel economy and driving (2/3)
Exhaust gas monitoring Sporty driving uses a lot of fuel: drive
system with a light right foot.
The exhaust gas monitoring system will Brake as little as possible. If you an-
detect any operating faults in the vehi- ticipate an obstacle or bend in ad-
cles antipollution system. vance, you may then simply release
If this system malfunctions, toxic sub- the accelerator pedal.
stances may be released into the at- Do not try to maintain the same
mosphere or damage may occur. speed up a hill, accelerate no more
than you would on the level. Keep
This warning light on the in-
strument panel will indicate if
there are any faults in the system:
your foot in the same position on the
accelerator pedal.
Double declutching and accelerating
This lights up when the ignition is before switching off are unnecessary
switched on and goes out when the in modern vehicles.
engine is started. Bad weather, flooded roads:
If it lights up continuously, consult an
approved Dealer as soon as possi- Do not drive through floods
Driving if the water is above the
ble; Drive carefully for the first few miles
if it flashes, reduce the engine speed lower edge of the wheel
until the engine reaches its normal rims.
until the light stops flashing. Contact operating temperature, rather than
your approved dealer as soon as let it warm up while the vehicle is sta-
possible. tionary.
Speed is expensive.
Do not overrev the engine in the in-
Obstructions to the driver
termediate gears.
On the drivers side, only
Always use the highest gear possi-
use mats adapted to the ve-
ble without labouring the engine.
hicle that attach to the pre-
On versions with an automatic gear-
installed parts, and regularly check
box, it is preferable to keep the gear
their mounting. Do not place several
lever in position D.
mats on top of each other.
Avoid sudden acceleration.
Risk of pedals jamming
2.15
Advice: antipollution, fuel economy and driving (3/3)
In vehicles fitted with air condi-
tioning, it is normal to observe an
increase in fuel consumption (es-
pecially in urban conditions) when
it is used. For vehicles fitted with
manual air conditioning, switch off
the system when it is not required.
Advice for reducing consumption
and therefore helping to preserve
the environment:
If the vehicle has been parked in the
sun, open the doors for a few mo-
ments to let the hot air escape before
starting the engine.
Never fill the fuel tank right to the
Advice on use brim to avoid overflow. Avoid using the car for door-to-door
calls (short journeys with long waits
Electricity is fuel; switch off all the Do not leave an empty roof rack in between) because the engine
electrical components which are fitted to the vehicle. never reaches its normal operating
not really needed. However (safety temperature.
It is better to fit a trailer for bulky ob-
first), keep your lights on when the
jects.
visibility is bad (see and be seen).
Use the air vents. Driving with the
When towing a caravan, fit a wind Tyres
deflector and adjust it carefully.
windows open at 60 mph (100 km/h) An underinflated tyre increases fuel
will increase fuel consumption by consumption.
4%.
The use of non-recommended tyres
can increase fuel consumption.
2.16
Environment
Your vehicle has been designed with Emissions At the end of the vehicles service
respect for the environment in mind for life, it should be sent to approved
its entire service life: during production, Your vehicle has been designed to centres to ensure that it is recycled.
use and at the end of its life. emit fewer greenhouse gases (CO2)
while in use, and therefore to consume In all cases, comply with local legis-
This commitment is illustrated by the lation.
Renault eco group signature. less fuel (eg. 140 g/km, equivalent to
5.3l/100km for a diesel vehicle).
Our vehicles are also equipped with a Recycling
particle filter system including a cata-
Your vehicle is 85% recyclable and
lytic converter, an oxygen sensor and
95% recoverable.
an active carbon filter (the latter pre-
vents vapour from the fuel tank being To achieve these objectives, many of
released into the open air). the vehicle components have been de-
signed to enable them to be recycled.
For certain diesel vehicles, this system
The materials and structures have
also has a particle filter to reduce the
been carefully designed to allow these
volume of soot particles emitted.
Manufacture components to be easily removed and
reprocessed by specialist companies.
Your vehicle has been manufactured at
an industrial site which uses a progress
Please make your own In order to preserve raw material re-
policy to reduce environmental impacts contribution towards sources, this vehicle incorporates nu-
on rivers and natural areas (reduc- protecting the environment merous parts made from recycled plas-
tion of water and energy consumption, too tics or renewable materials (vegetable
visual and noise pollution, atmospheric or animal-derived materials such as
Worn parts replaced in the course of cotton or wool).
emissions and waste water, sorting and
routine vehicle maintenance (vehi-
reusing waste).
cle battery, oil filter, air filter, batter-
ies, etc.) and oil containers (empty or
filled with used oil) must be disposed
of through specialist organisations.
2.17
TYRE PRESSURE MONITOR (1/3)
This system monitors the tyre pressure.
The pressures must be adjusted
when the tyres are cold.
If the tyre pressures cannot be checked The operation of the tyre pressure
when the tyres are cold, assume an in- monitor may be affected by using
crease of 0.2 to 0.3 bar (or 3 PSI). devices near the vehicle which op-
Never deflate a hot tyre. 1 erate on the same frequency.
In this case, the system indicates a
drop in tyre pressure under normal
conditions.
The operation of the tyre pressure
monitor may be affected if snow
chains are fitted to the tyres or if the
tyres are stuck in snow.
Operating principle
Each wheel (except for the emergency
spare wheel) has a sensor in the infla-
tion valve which periodically measures
This function is an addi- the tyre pressure.
tional driving aid. The system informs the driver via the
However, the function does trip computer and warning system1
that the tyres are sufficiently inflated Changing a wheel
not take the place of the
driver. It cannot, therefore, under and warns if they are underinflated or Depending on use, the
any circumstances replace the vig- leaking. system may take several
ilance or the responsibility of the minutes for the new wheel
driver. positions and pressures to be rec-
ognised; check the tyre pressures
Check the tyre pressures, including after all operations.
the emergency spare wheel, once a
month.
2.18
TYRE PRESSURE MONITOR (2/3)
Changing a wheel Emergency spare wheel
The tyre pressure monitor takes ap- The emergency spare wheel has no
proximately 8 minutes to identify the sensor, and cannot be recognised by
tyres which have been replaced. The the system.
system will not operate during this time. When it is fitted in the place of another
wheel, the system then detects an op-
Fitting tyres erating fault. 1
2
(replacing tyres or fitting winter
tyres) Replacing wheels/tyres
Since replacing tyres requires special This system requires specific equip-
precautions, we advise you to contact ment (wheels, hubcaps, etc.).
your approved dealer.
Contact an approved dealer to fit new
tyres and to find out about available ac-
cessories compatible with the system
and available from your approved Display
dealer: the use of any other accessory If warning lights1 and2 light up on the
could affect the correct operation of the instrument panel, this indicates there
system or damage a sensor. is a fault relating to the tyre pressure
(flat tyre, puncture, system malfunction,
etc.).
An explanation of the indicator lights,
signals and messages is given on the
While the tyre pressure following page.
monitor is identifying the
tyres which have been re-
placed, the information sent
by the system may be inaccurate
and this could have serious conse-
quences.
2.19
TYRE PRESSURE MONITOR (3/3)
Examples of messages which may appear on the instrument panel displays
Check tyre
The tyre pressure is lower than normal.
pressure
Indicator light comes on, accompanied by a bleep. Stop the vehicle as soon as
Significant possible and contact an approved dealer.
under-inflation The tyre pressure indicated is much lower than normal and is becoming dangerously
low.
Indicator light comes on, accompanied by a bleep. Stop the vehicle as soon as
Puncture possible and contact an approved dealer.
The tyre indicated is deflated or punctured.
Check tyre sensor One of the tyres is no longer being displayed; there is a fault with the sensor on this tyre.
Check tyre sensor None of the tyre pressure sensors can be detected, or there is a fault with the system.
Tyre sensor There is no signal being received from the tyre indicated and the tyre can no longer be
missing monitored by the pressure sensor (emergency spare wheel fitted, etc.).
2.20
All-wheel drive system: 4 wheel drive (4WD) (1/3)
AUTO" mode 4WD Lock" mode
This is the mode defined each time Press the bottom section of button1.
the engine is started. The button returns immediately to its
2.21
All-wheel drive system: 4 wheel drive (4WD) (2/3)
Operating faults
When the system detects an operating
fault the message Check 4WD and
warning light appear on the in-
as soon as the vehicle speed strument panel.
exceeds 24 mph (40km/h) in
4WD Lock mode, the system Contact your approved Dealer as soon
automatically switches back to as possible.
AUTOmode. The indicator light
goes out;
Special note on all-wheel
when the front and rear wheels
drive system are turning at different speeds
The vehicle may make more (for example, when driving on
noise when the AUTO" or "4WD uneven road surfaces, sand or
Lock" modes are activated. This mud, or when being towed, tyres
is normal; with different levels of wear), the
if the system detects a difference oil temperature may rise, given
in the size of the front and rear the mechanical stresses. In this
wheels (as is the case, for exam- case, the system automatically
ple, when the wrong size tyres switches back to 2WD mode to
are fitted, or if the tyres are un- prevent overheating. The mes-
der-inflated or significantly worn sage 4WD unavailable is dis-
on one axle etc.) the message played on the instrument panel
4WD unavailable is displayed
on the instrument panel and the
and the or indica-
tor light comes on. Park the ve-
indicator light flashes.
Select 2WD mode and drive at
hicle in a safe place and wait until
the message 4WD unavailable
a moderate speed; disappears.
always use four tyres with the If the warning appears again,
same level of wear; contact an approved Dealer.
2.22
All-wheel drive system: 4 wheel drive (4WD) (3/3)
It is recommended not to use 4WD Lock" mode permanently when driving on roads in good condition.
Always ensure tyres with identical specifications are fitted to all four wheels (brand, size, structure, wear etc.). Fitting tyres
of different sizes to the front and rear wheels and/or left and right wheels may have serious consequences for the tyres,
gearbox, transfer gearbox and the rear differential pinions.
2.23
Driver correction devices/aids (1/5)
Depending on the vehicle, this is com- ABS (anti-lock braking Operating faults:
posed of: system) If the message Check ABS is dis-
the anti-lock braking system ABS;
the electronic stability program
Under heavy braking, the ABS prevents
the wheels from locking, allowing the
played and the x and
warning lights on the instrument
ESP with traction control ASR; stopping distance to be managed and
the emergency brake assist; panel come on when driving, brak-
keeping control of the vehicle. ing safety is still guaranteed, but
the hill descent control;
the hill start assistance. Under these circumstances, the vehi- without ABS;
cle can be steered to avoid an obstacle if the message braking system
whilst braking. In addition, this system
can increase stopping distances, par-
ticularly on roads with low surface grip
fault is displayed and the D
and warning lights on the in-
(wet ground etc.). strument panel come on when driv-
You will feel a pulsation through the ing, there is a fault in the braking
These functions are an ad- system.
brake pedal each time the system is
ditional aid in the event of
activated. The ABS does not in any way Consult an approved Dealer.
critical driving conditions,
improve the vehicle's physical perform-
enabling the vehicle behav-
ance relating to the road surface and
iour to be adapted to suit the driving
roadholding. It is still essential to follow
conditions.
the rules of good driving practice (such
However, the functions do not take as driving at a safe distance from the
the place of the driver. They do vehicle in front etc.).
not increase the vehicles limits
and should not encourage you
to drive more quickly. Therefore,
they can under no circumstances Your braking systems
replace the vigilance or responsibil- are partially operational.
ity of the driver when manoeuvring However, it is dangerous
the vehicle (the driver must always In an emergency, apply firm and to brake suddenly and
be ready for sudden incidents which continuous pressure to the brake it is essential to stop immediately,
may occur when driving). pedal. There is no need to pump as soon as traffic conditions allow.
it repeatedly. The ABS will modu- Contact an approved dealer.
late the force applied in the braking
system.
2.24
Driver correction devices/aids (2/5)
Electronic stability program Traction control ASR Operating faults
ESP with understeer control This system helps to limit wheelspin of When the system detects an operat-
and traction control ASR the drive wheels and to control the ve- ing fault the message Check ESP and
hicle when pulling away accelerating or warning light appear on the in-
Electronic stability program ESP decelerating. strument panel. In this case, the ESP
This system helps you to keep control Operating principle and ASR are deactivated.
of the vehicle in critical driving condi- Using the wheel sensors, the system Consult an approved dealer.
tions (avoiding an obstacle, loss of grip measures and compares the speed of
on a bend, etc.). the drive wheels at all times and slows
down their over-rotation. If a wheel is
Operating principle starting to slip, the system brakes au-
A sensor in the steering wheel detects tomatically until the drive supplied be-
the direction selected by the driver. comes compatible with the level of grip
Other sensors throughout the vehicle under the wheel again.
measure the actual direction. The system also adjusts the engine
The system compares the direction se- speed to the grip available under the
lected by the driver and the actual di- wheels, independently of the pressure
rection of the vehicle and corrects this exerted on the accelerator pedal.
as necessary by applying the brakes
selectively and/or acting on the engine
power.
2.25
Driver correction devices/aids (3/5)
If you deactivate this function, the Emergency brake assist
traction control (ASR) system will
also be deactivated. This system supplements the ABS
As the ESP and ASR provide enhanced and helps reduce vehicle stopping dis-
safety, it is not advisable to drive with tances.
the function switched off. Correct Operating principle
this as soon as possible by pressing
switch1 again. Depending on the speed at which the
brake pedal is depressed, the system
will detect emergency braking. In this
case, the braking assistance immedi-
ately develops maximum power and
may trigger ABS regulation.
1
ABS braking is maintained as long as
the brake pedal is applied.
Disabling the ESP function Hazard warning lights switching on
In some situations (driving on very wet Depending on the vehicle, these may
ground: snow, mud, etc. or driving with light up in the event of sudden decel-
snow chains fitted), the system may eration.
reduce the engine output to limit wheel-
spin. If this is not required, it is possible
to deactivate the function by pressing
switch1.
The message ESP deactivated is dis-
played on the instrument panel along
with the
you.
warning light to inform
2.26
Driver correction devices/aids (4/5)
Starting the system The hill descent control system is de-
With the vehicle travelling downhill at activated as soon as you depress the
less than 15 mph (25 km/h) in first or re- brake pedal or the accelerator pedal,
verse gear (position D or R for vehicles and reactivated as soon as you release
1 with an automatic transmission), press it.
switch2 to switch to 4WD Lock mode.
Once a sufficient gradient is detected,
the warning light appears on the
instrument panel, accompanied by the
With the engine cold, the
automatic hill descent con-
trol function can be de-
HDC operational message. activated temporarily (the
2
Note: if the vehicle speed exceeds
24 mph (40 km/h), the transmission
warning light goes out).
When the engine temperature rises,
switches automatically to AUTO mode the warning light comes on again
(the warning light goes out).
and the function is available.
The automatic hill descent control
Hill descent control The system can be reactivated by
system may be deactivated tempo-
This function enables the vehicle speed pressing 4WD Lock when the vehicle
rarily if there is a risk of the braking
to be limited to approximately 4 mph speed drops below 24 mph (40 km/h).
system overheating.
(7km/h), without depressing the brake
pedal (when driving down a steep hill). If necessary, use the brake pedal to
stop the vehicle.
Activating/deactivating the system The driver must remain particularly
Activating: press button1. The vigilant when driving on slippery or
message HDC activated appears low-grip surfaces and/or on hills.
on the instrument panel. Risk of serious injury.
Deactivating: press button1 again:
the message HDC deactivated ap-
pears on the instrument panel. This system does not operate when
the gear lever is in neutral (position
N or P for vehicles with an auto-
matic transmission), or if the vehicle
is travelling on flat ground.
2.27
Driver correction devices/aids (5/5)
Hill start assistance
This function assists the driver when
starting on hills. It prevents the vehicle
from rolling backwards, depending on The hill start assistance
the slope, by automatically applying the system cannot completely
brakes when the driver lifts his/her foot prevent the vehicle from
off the brake pedal to depress the ac- rolling backwards in all sit-
celerator pedal. uations (extremely steep gradients,
etc.).
System operation
In all cases, the driver may depress
It only operates when the gear lever is the brake pedal to prevent the vehi-
in a position other than neutral (other cle from rolling backwards.
than N or P for automatic transmis-
The hill start assistance function
sions) and the vehicle is completely
should not be used for prolonged
stationary (brake pedal depressed)
stops: use the brake pedal.
The system holds the vehicle for ap-
This function is not designed to im-
proximately 2 seconds. The brakes are
mobilise the vehicle permanently.
then gradually released (the vehicle will
move according to the slope). If necessary, use the brake pedal to
stop the vehicle.
The driver must remain particularly
vigilant when driving on slippery or
low-grip surfaces and/or on hills.
Risk of serious injury.
2.28
CRUISE CONTROL/SPEED LIMITER: speed limiter function (1/3)
2 3
5 4 6
1
2.29
CRUISE CONTROL/SPEED LIMITER: speed limiter function (2/3)
Varying the limit speed Exceeding the limit speed
To vary the limit speed, press switch2 It is possible to exceed the limit speed
(+) repeatedly to increase the speed or at any moment. To do this: press the
switch5 (-) to decrease. accelerator pedal firmly and fully
2 3 (beyond the kickdown point).
Whilst the speed is being exceeded,
the cruising speed displayed on the in-
strument panel flashes.
5 4 Then, release the accelerator pedal:
the speed limiter function will return as
soon as you reach a speed lower than
the stored speed.
2.30
CRUISE CONTROL/SPEED LIMITER: speed limiter function (3/3)
Recalling the limit speed
If a speed has been stored, it can be re-
called by pressing switch3 (R).
2 3
5 4
1
2.31
Cruise control/speed limiter: cruise control function (1/4)
5 4
1
This function is an addi-
tional driving aid.
However, the function does
The cruise control function helps you to not take the place of the Controls
maintain your driving speed at a speed driver. Therefore, it can under no
circumstances replace the drivers 1 Main On/Off switch.
that you choose, called the cruising
speed. responsibility to respect speed limits 2 Cruising speed activation, storage
and to be vigilant (the driver must and increase switch (+).
This cruising speed may be set at any always be ready to brake). Cruise
speed above 20 mph (30 km/h). control must not be used in heavy 3 Cruising speed activation, storage
traffic, on winding or slippery roads and recall (R).
(black ice, aquaplaning, gravel) and 4 Switch the function to standby (with
during bad weather (fog, rain, side stored cruising speed) (O).
winds etc.). 5 Cruising speed activation, storage
There is a risk of accidents. and decrease switch ().
2.32
Cruise control/speed limiter: cruise control function (2/4)
2 3
6 7
5 4
1
2.33
Cruise control/speed limiter: cruise control function (3/4)
Exceeding the cruising speed
The cruising speed may be exceeded
at any time by depressing the accelera-
2 3 tor pedal. While it is being exceeded,
the cruising speed flashes on the in-
strument panel.
Then, release the accelerator: after a
few seconds, the vehicle will automati-
cally return to its set cruising speed.
5 4
Cruising speed cannot be
maintained
When driving down a steep gradient,
the system is unable to maintain the
cruising speed: the stored speed will
Adjusting the cruising speed flash on the instrument panel informa-
The cruising speed may be changed by tion display to inform you of this situ-
pressing the following repeatedly: ation.
switch2 (+) to increase the speed;
switch5 (-) to decrease the speed.
2.34
CRUISE CONTROL/SPEED LIMITER: cruise control function (4/4)
Returning to the cruising speed
If a speed is stored, it can be recalled,
once you are sure that the road condi-
2 3 tions are suitable (traffic, road surface,
weather conditions, etc.). With a ve-
hicle speed above 20 mph (30 km/h),
press switch3 (R).
Note: if the speed previously stored is
much higher than the current speed,
5 4 the vehicle will accelerate more rapidly
to reach this threshold. 1
2.35
PARKING DISTANCE CONTROL (1/2)
Operating principle Operation
When reversing, when any object is
On equipped vehicles, ultrasonic sen- detected approximately 1.50 metres
sors fitted in the vehicles rear and/or from the vehicle: a beep sounds.
front bumper measure the distance When moving forwards at less than
between the vehicle and an obstacle 7mph (12 kph), when any object is de-
when reversing. tected less than approximately 1 metre
This measurement is indicated by from the vehicle: a beep sounds.
beeps which become more frequent the If there are obstacles located close to
closer you come to the obstacle, until both the front and rear of the vehicle,
they become a continuous beep when only the closest of the two will be ac-
the vehicle is approximately 25 centi- knowledged and the corresponding
metres from the obstacle. front or rear beep sound will be emit-
Special features ted. If obstacles are detected both to
the front and to the rear of the vehicle
Ensure that the ultrasonic sensors are at the same time, and they are both
not obscured (by dirt, mud, snow, etc.). within 30 centimetres from the vehicle,
the corresponding front and rear beeps
will be emitted alternately.
2.36
PARKING DISTANCE CONTROL (2/2)
Activating/deactivating for long
periods
Press the switch for approximately
3seconds to deactivate the system:
the indicator light on the switch comes
on and the message parking distance
control deactivated is displayed on the
instrument panel.
The system is reactivated by press-
ing the switch again for approximately
1 3seconds.
Operating faults
When the system detects an operat-
ing fault, the message check parking
Activating and deactivating Temporary activation/deactivation
distance control is displayed on the
the system Press switch1 to deactivate the system: instrument panel, the warning
the indicator light on the switch comes light comes on and a beep sounds.
Automatic activation/deactivation on and the message parking distance
control deactivated is displayed on the Consult an approved Dealer.
The system deactivates:
instrument panel.
when the electronic parking brake is
applied; The system is reactivated by pressing
the switch.
when the vehicle speed is above ap-
proximately 7 mph (12 km/h); Note: in this case, the system is au-
tomatically reactivated each time the
when the vehicle is in neutral or engine is switched off.
when the gear lever has been shifted
to N or P for automatic gearboxes. When the vehicle is being driven at
a speed below 7 mph (12 kph), cer-
tain noises (motorcycle, lorry, pneu-
matic drill, rain, alarm etc.) may trig-
ger the beeping sound.
2.37
Automatic or continuously variable transmission (1/3)
Driving in automatic mode
2 Select position D. In most traffic con-
ditions, you will not have to touch the
gear selector lever again: the gears will
1 change automatically at the right time
and at the most suitable engine speed
because the automatic system takes
into account the vehicle load and road
3 contour and adjusts itself to the particu-
lar driving style you have chosen.
4
A 5 Economical driving
When driving, always leave the lever
6 in position D, keeping the accelerator
8 7 pedal lightly depressed to ensure auto-
matic gear changes at a lower engine
Depending on the vehicle, the vehicle is Operation speed.
either fitted with an automatic transmis-
sion, or a continuously variable trans- N With the gear lever2 in position P,
switch on the ignition. Accelerating and overtaking
mission. Depress the accelerator pedal firmly
To move out of position P, you must de- and fully (so that it goes beyond the
press the brake pedal before pressing kickdown point).
Selector lever2 the unlocking button1.
DisplayA on the instrument panel This will enable you to change down
With the foot on the brake pedal (warn- to the optimum gear within the
ing light c on displayA goes out),
shows the mode and gear selected.
engine range.
3: P: park move the lever out of position P.
4: R: reverse gear
Only engage D or R when the vehi-
5: N: neutral
cle is stopped, with your foot on the
6: D: automatic mode
brake and the accelerator pedal re-
7: manual mode
leased.
8:zone displaying gearbox mode or
gear engaged in manual mode
2.38
Automatic or continuously variable transmission (2/3)
Driving in manual mode Special circumstances Parking the vehicle
With the selector lever in position D, If the bends and road surface do When the vehicle is stopped, move the
move the lever to the left. Shifting the not allow you to stay in automatic lever to position P while keeping your
lever repeatedly allows you to change mode (e.g. in the mountains), we foot on the brake pedal: the gearbox is
gears manually: recommend that you change to in neutral and the drive wheels are me-
backwards to shift down the gears; manual mode. chanically locked by the driveshaft.
forwards to shift up the gears. This will prevent repeated gear Depending on the vehicle, apply the
changes when climbing and will handbrake or check that the elec-
The gear selected is displayed on the enable engine braking on long de- tronic parking brake is on (refer to
instrument panel. scents. the information on the Parking brake in
In very cold weather, to avoid stall- Section 2).
Special cases ing the engine, start the engine and
wait a few seconds before moving
Under certain driving conditions (e.g.
the lever from position P or N to po-
engine protection, or electronic stabil-
sition D or R.
ity program (ESP) operational etc.):
E.S.Pthe automatic system may Vehicles not fitted with traction
change gear automatically. control: to avoid wheelspin when
starting on a slippery or low grip sur-
Likewise, to prevent incorrect manoeu-
face, change to manual mode and
vres, a gear change may be refused by
select second gear before moving An impact to the under-
the automatic system: in this case the
off. side of the vehicle while
gear display flashes for a few seconds
manoeuvring (e.g.: strik-
as a warning.
ing a post, raised kerb or
other street furniture) may result in
damage to the vehicle (e.g.: defor-
mation of an axle).
To avoid any risk of accident, have
your vehicle checked by an ap-
proved Dealer.
In very cold weather, the system may prevent the gears from being shifted in
manual mode until the gearbox reaches the right temperature.
2.39
Automatic or continuously variable transmission (3/3)
Operating faults
when driving, if the check gearbox
message appears on the instrument
panel, it indicates a fault.
Contact your approved Dealer as
1
soon as possible.
when driving, if the message gear-
box overheating appears on the in- 9
strument panel, shift the gear lever
into position N, as soon as possible.
Contact your approved dealer as
soon as possible.
If a vehicle with an automatic
gearbox breaks down, refer to the
information on Towing in Section 5. When setting off, if the lever is locked
in position P even though you are de-
Special note for vehicles equipped pressing the brake pedal and pressing
with continuously variable unlocking button1, the lever can be re-
transmissions: leased manually. To do this, unclip the
cover9 at the base of the lever. Then,
Under certain driving conditions at high
simultaneously press:
speeds, the gearbox may temporarily
limit the maximum engine speed. This press the button located under
is normal. cover5 (using a flat-blade screw-
driver or similar tool);
depress the brake pedal;
press button1.
Then shift the lever.
2.40
Section 3: Your comfort
1 2 3 4 5 6 7
9 8
5 control panel
3.2
AIR VENTS, air outlets (2/2)
1 1
1
2
3
2 2
3.3
Manual air conditioning/heating system (1/3)
Air recirculation mode
A B C D E Press the button B: the indicator light
on the button comes on.
In these conditions air is taken from the
passenger compartment and is recircu-
lated, with no air being taken from out-
side the vehicle.
Recirculation allows:
isolating the vehicle from the exter-
nal atmosphere (driving in polluted
areas, etc.);
F
the passenger compartment to be
brought to the desired temperature
more quickly.
Controls Temperature adjustment
(depending on vehicle) Turn the control A according to the
A Adjusting the air temperature. required temperature. The further to-
B Air recirculation activation/deactiva- wards the red the slide is, the higher the
tion. temperature will be.
3.4
MANUAL AIR CONDITIONING/HEATING SYSTEM (2/3)
Switching air conditioning on
A B C D E or off
The air conditioning is switched on (in-
dicator light illuminated) or off (indicator
light extinguished) using buttonF.
3.5
MANUAL AIR CONDITIONING/HEATING SYSTEM (3/3)
Rear screen de-icing/
A B C D E demisting
Press button D: the indicator light on
the button comes on.
This function is used to prevent con-
densation forming on the rear screen.
To switch it off, press buttonD again.
3.6
automatic climate control (1/6)
13 12 11 10 DUAL function
Pressing button3 for more than 2 sec-
The controls 6 Ventilation speed adjustment.
onds sets the passenger temperature
(depending on vehicle) 7 Rear screen and door mirror de-ic- to the drivers temperature.
1 Left-hand temperature adjustment. ing/demisting.
2 Left-hand temperature display.
3 Automatic mode on/off switch. DUAL 8 Maximum de-icing.
function. 9 Right-hand temperature adjustment.
4 Air conditioning on/off switch.
5 Main On/Off switch. 10 Right-hand temperature display.
11 Air recirculation control.
12 Adjustment of distribution of air in the
passenger compartment.
13 Ventilation adjustment in the rear
seats. There is an indicator light on each
Information and advice on use button.
Refer to information on Air condi- Indicator light on, the function is
tioning: information and advice on switched on.
use. Indicator light off, the function is
switched off.
3.7
automatic climate control (2/6)
3
3.8
automatic climate control (3/6)
3 4 5 6
3.9
automatic climate control (4/6)
Clear View function
3 6 7 8
Press button8: the integrated indicator
light comes on.
This function quickly demists and de-
ices the windscreen, the rear screen,
the front side windows, and the door
mirrors (depending on the vehicle). The
air conditioning and rear screen de-ic-
ing functions must be activated.
Press button7 to stop the heated rear
screen operating, and the integrated in-
dicator goes out.
You can change the ventilation speed
by turning control6.
To exit this function, press: Rear screen de-icing/
button8 again; demisting
button3. Press button7: the integrated indica-
tor light comes on. This function per-
mits rapid demisting/de-icing of the rear
screen and de-icing of the door mirrors
(on equipped vehicles).
To exit this function, press button7 In cold weather, the ventilation
again. Demisting automatically stops system does not come on automati-
by default. cally at maximum speed in auto-
matic mode: the speed is increased
gradually until the engine is warm
enough to heat the air in the pas-
senger compartment. This may take
from a few seconds to several min-
utes.
3.10
automatic climate control (5/6)
12
Distribution of air in the
passenger compartment
All the air flow is directed to the
demisting vents for the wind-
screen and the side windows.
There are five possible combinations
for air distribution and these can be se-
lected by pressing buttons12.
All the air flow is directed to the
windscreen demisting vents,
the side windows and the dashboard
The indicator lights on the buttons show vents.
which mode has been selected. This setting maintains the optimum
temperature level in cold weather.
If manual mode is used for air distri-
bution, the operating indicator light
on button3 goes out (automatic
mode). Only the air distribution func-
tion is no longer automatically con-
trolled by the system.
Press button3 to return to auto-
matic mode.
3.11
automatic climate control (6/6)
14 15
17
16
13 11 18
Setting the air recirculation Prolonged use of this position may lead Flow of air from rear air
mode to odours, caused by non-renewal of vents.
air, and the formation of condensation (depending on vehicle)
Pressing button11 activates air recircu- on the windows.
lation mode (the symbol lights up on the Repeatedly pressing buttons13 or17
display). We therefore advise you to return to enables the ventilation speed in the
normal mode (external air or automatic rear seats to be modified, according to
During recirculation, air is taken from recirculation) as soon as air recircula-
the passenger compartment and is re- three different settings:
tion is no longer needed, by pressing
cycled, with no air being taken from out- button11. slow speed (indicator lights14
side the vehicle. and18 on);
Air recirculation allows the passenger fast speed (indicator lights15 and16
compartment to be isolated from the on);
outside air (when driving in polluted park.
areas, etc.).
3.12
Air conditioning: information and advice on use
Advice on use
In some situations, (air conditioning Operating faults
off, air recirculation activated, venti- Fuel consumption As a general rule, contact your ap-
lation speed at zero or low, etc.) you You will normally notice an increase proved dealer in the event of an op-
may notice that condensation starts in fuel consumption (especially erating fault.
to form on the windows and wind- when driving in town) when the air Reduction in de-icing, demist-
screen. conditioning is operating. ing or air conditioning per-
If there is condensation, use the For vehicles fitted with manual air formance. This may be caused
Clear View function to remove it, conditioning, switch off the system by the passenger compartment
then use the air conditioning in auto- when it is not required. filter cartridge becoming clogged.
matic mode to stop it forming again.
No cold air is being produced.
Advice for reducing Check that the controls are set
consumption and therefore correctly and that the fuses are
helping to preserve the sound. Otherwise, switch off the
environment: system.
Drive with the air vents open and
Note the windows closed.
Presence of water under the ve- If the vehicle has been parked in
hicle. After prolonged use of the air the sun, open the doors for a few
conditioning system, it is normal for moments to let the hot air escape
water to be present under the vehi- before starting the engine.
cle. This is caused by condensation.
Maintenance
Refer to the Maintenance Service
Booklet for your vehicle for the in- Do not open the refriger-
spection frequency. ant fluid circuit. The fluid
may damage eyes or skin.
3.13
Electric windows (1/2)
Special note: the electric windows op-
erate up to approximately 45 seconds
after the engine is switched off or until
the drivers door is opened.
5 1 6
2
4 3 Drivers responsibility
Never leave your vehicle
with the RENAULT card
With the ignition on, press the switch Front and rear passenger inside and never leave a
to lower the window to the required child (or a pet) unsupervised, even
seats for a short period of time.
level;
Press switch6. They may pose a risk to themselves
Lift the switch to raise the window to the
desired height. or to others by starting the engine,
activating equipment such as the
electric windows or by locking the
From the drivers seat doors.
Operate the switches as follows: If something gets trapped, reverse
1 for the drivers side; the direction of travel as soon as
possible by pressing the relevant
2 for the front passengers side; switch.
Safety of rear occupants
3 and5 for the rear passenger win- Risk of serious injury.
The driver can inhibit opera-
dows.
tion of the rear electric win-
dows by pressing switch4.
3.14
Electric windows (2/2)
One-touch windows Remote control window Operating faults
When the vehicle is equipped with this closing In case of a fault when closing a window,
function, the one-touch mode works in (for vehicles with one-touch windows the system reverts to normal mode: pull
addition to the operation of the electric on all windows). the switch concerned up to fully close
windows described previously. When you lock the doors from the out- the window, then hold the switch (still
Fully and briefly press down on the side, press the locking button on on the closure side) for three seconds
relevant switch down: the window the RENAULT card or, in hands-free then lower and raise the window fully to
will open completely. mode, the door or tailgate button, reinitialise the system.
twice in quick succession, and the If necessary, contact an approved
Fully and briefly lift the relevant windows will close automatically.
switch: the window will close com- Dealer.
pletely. It is recommended that the user only
operates the system when the vehi-
Pressing the switch again while the cle can be seen clearly and no one is
window is moving will stop its move- inside.
ment.
Special note: for vehicles fitted with
This mode can be fitted to the drivers the deadlocking function, refer to infor-
window only or to all of the windows: mation on the RENAULT card: dead-
press switches1,2,3,5, or6. locking" in section 1.
Special features Note: closing the windows with the
If the window detects resistance when RENAULT card deactivates hands-free
closing (e.g.: fingers, branch of a tree, mode.
etc.) it stops and then lowers again by a
few centimetres.
If you use the switch while the window
is moving, it stops working.
3.15
Electric sunroof (1/2)
The system operates:
when the ignition is switched on,
when the ignition is switched off until
A the drivers door is opened/closed
(limited to approximately 45 sec-
B onds).
2
Drivers responsibility
Never leave your vehicle
with the RENAULT card
Sunroof blind Tilting the sunroof inside and never leave a
Opening: open the sunroof blind, then child (or a pet) unsupervised, even
Move handles1 forwards or backwards for a short period of time.
to open the blind as required. press button2 (sideA): the sunroof tilts
open. They may pose a risk to themselves
Closing: press2 (sideB). or to others by starting the engine,
activating equipment such as the
electric windows or by locking the
Sliding the sunroof doors.
Opening: open the sunroof blind then If something gets trapped, reverse
briefly press button2 (sideA) the direction of travel as soon as
Using button2 stops the sunroof possible by pressing the rear of
moving. button2 (on the side markedA).
Closing: briefly press2 (sideB). Risk of serious injury.
3.16
Electric sunroof (2/2)
Closing the sunroof by Precautions during use
remote control check that the sunroof is properly
(for vehicles equipped with one-touch closed before leaving your vehicle;
windows on all windows).
When you lock the doors from the out-
A clean the seal every three months
using products recommended by our
side, press the locking button on
B Technical Department;
the RENAULT card or, in hands-free
mode, the door or tailgate button 2 do not open the sunroof immedi-
twice in quick succession and the ately after the vehicle has been in
windows and sunroof will close auto- the rain or after your car has been
matically. washed.
Vehicle with roof bars
Special note
Your vehicle is equipped with an anti- As a general rule, if there is a load
pinch facility: when the sunroof encoun- on the roof, use of the sunroof is not
ters resistance whilst closing, (some- recommended.
bodys fingers, etc.) it stops and then Note: for vehicles fitted with the dead-
Before using the sunroof, check the
moves back several centimetres. locking function, refer to information on
objects and/or accessories (bike
It is recommended that the user only the RENAULT card: deadlocking" in
racks, roof boxes, etc.) attached to
operates the system when the vehi- section 1.
the roof bars: they should be prop-
cle can be seen clearly and no one is erly arranged and secured and
inside. Sunroof operating fault
should not interfere with the opera-
In this case, check that there are no tion of the sunroof.
obstacles, then move button2 to posi-
tionB until the sunroof is fully closed. Contact your approved Dealer for
details of possible conversions.
3.17
SUN VISOR
1 2 4
3.18
Sun visor/child minder mirror
6 8
7 7
3.19
Interior lighting (1/2)
1 2
3
5
3.20
Interior lighting (2/2)
6 9 10
7 8
3.21
PASSENGER COMPARTMENT STORAGE/FITTINGS (1/6)
2
1 3 4
5 7
6
Passenger storage Depending on the vehicle, this storage Front door armrest storage6
compartment compartment has:
Pull handle1 to open it. a card holder2 Door pockets7
It can hold A4 size documents, large
bottles of water, etc. an air vent: depending on the vehi- It can hold books, maps, cups, etc.
cle, use control3 to open or close it.
The air comes from the outside or
from the air conditioning system.
a storage compartment for a
mobile phone 4. Ensure that no hard, heavy
Nothing should be placed or pointed objects are
on the floor area in front of placed in the open storage
Vehicle documentation compartments in such a
the driver as such objects
may slide under the pedal storage compartment5 way that they may fall on any pas-
during braking manoeuvres, thus sengers during sudden turning,
obstructing its use. braking or in the event of an acci-
dent.
3.22
PASSENGER COMPARTMENT STORAGE/FITTINGS (2/6)
12
10
13
8
9 B
A
14
15
11
3.23
PASSENGER COMPARTMENT STORAGE/FITTINGS (3/6)
18
C 21
16 17 20
E
19 F
3.24
PASSENGER COMPARTMENT STORAGE/FITTINGS (4/6)
22 24
23 25 27
26
Handle for holding bags Rear parcel shelves24 Rear door storage
whilst cornering22 (depending on vehicle) compartment27
This offers support and can be held Raise it to the horizontal position. This can be used to store books, drinks
when the vehicle is moving. Do not use or maps.
these for getting into or out of the ve- Storage pockets25
hicle.
3.25
PASSENGER COMPARTMENT STORAGE/FITTINGS (5/6)
30 31 32
28
33
29
3.26
PASSENGER COMPARTMENT STORAGE/FITTINGS (6/6)
35
36
37
34
Storage compartment under Lift the handle then attach the hook35 Depending on the vehicle, these stor-
the luggage compartment to the ring36. age compartments are available37.
carpet.
Press control34, to access the handle.
3.27
ASHTRAY/CIGAR LIGHTER/ACCESSORIES SOCKET
1 4
5
3.28
rear bench seat functions (1/2)
1 2
5
3
To fold down the rear To fold down the rear seats To return the seat to its
seats from the luggage from inside the passenger original position
compartment compartment lift the seatback and return it to its
(depending on vehicle) lower the headrest; original position;
lower the headrests; move the front seat as far forward as fold down the seat base2;
move the front seat as far forward as necessary; ensure that the seat is correctly
necessary; feed the seat belt into the clip5; locked in position.
feed the seat belt into the clip5; pull lever3: the seat base is raised; When the seat belt is not being used,
use the controls1. pull handle4 and fold down the seat- attach it to hook5.
back.
3.29
rear bench seat functions (2/2)
3.30
Luggage compartment (1/2)
A
1
Max 200 Kg
A
2
B
B
3.31
Luggage compartment (2/2)
5
A
2 3
B
To close the tailgate Next, lower the upper sectionA and Opening the tailgate from
close it. inside the vehicle
Lift the lower sectionB of the tailgate,
then close it. For your comfort, use handle3 on the If the tailgate cannot be opened from
tailgate to close it. the outside, it can be opened from
Note: always ensure that the lower inside the vehicle.
section of the tailgate is properly closed Move the rear seats forwards and
before closing the upper section. down and climb into the luggage
compartment;
remove cover5 using a screwdriver
or suitable tool;
move control4;
push the upper section of the tailgate
to open it.
3.32
LUGGAGE COMPARTMENT COVER
A
1 2
3
To unfold the flexible section Removing the luggage cover Luggage compartment cover
of the luggage compartment Press the two ends3 and move them storage
cover towards the centre of the luggage com- Move the parcel shelf up (move-
Pull handle1 located under the cover partment cover, then tilt the cover. mentA).
and place each end of the cover in the Caution: the luggage compartment Remove the luggage compartment
notch2. cover is heavy. cover and place it in positionB.
To fit the luggage compartment cover,
To remove the flexible proceed in reverse order.
section of the luggage Note: it is easier to remove the lug-
compartment cover gage compartment cover if the lower
section of the tailgate is closed. Do not place any heavy or
Pull handle1 then lift it while unfolding
hard objects on the luggage
the luggage compartment cover.
cover. These may pose a
risk to the vehicle occu-
pants if the driver has to brake sud-
denly or if the vehicle is involved in
an accident.
3.33
Transporting objects in the luggage compartment/Towing (towing equipment)
32177
32178
A B
C
3.34
Anchorage points/Luggage net
3
1
3.35
ROOF BARS
1
3.36
multimedia equipment
The presence and location of this
equipment depends on the vehicles
multimedia equipment. 1
1 Radio;
2 central control;
3 steering column control;
4 microphones;
5 multimedia sockets. 2
4
Hands-free telephone
integrated control
On equipped vehicles, use micro-
phones4 and steering column con-
trol3.
3.37
3.38
Section 4: Maintenance
Bonnet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2
Engine oil level: general information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4
Engine oil level: topping up, filling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.6
Engine oil change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.7
Levels:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.8
coolant. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.8
brake fluid. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.9
windscreen/headlight washer reservoir. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.10
Filters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.10
Tyre pressures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.11
Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.12
Bodywork maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.13
Interior trim maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.15
4.1
Bonnet (1/2)
4.2
Bonnet (2/2)
Closing the bonnet
Check that nothing has been left in the
engine compartment.
5 To close the bonnet, replace stay4
back into its holder5, hold the bonnet in
4
the middle and lower it to 30 cm above
the closed position, then release it. It
will latch automatically under its own
weight.
4.3
ENGINE OIL LEVEL: general information (1/2)
It is normal for an engine to use oil for
lubrication and cooling of moving parts
and it is normal to top up the level be-
tween oil changes. 3
However, contact an approved Dealer if
more than 0.5 litres is being consumed
every 600 miles (1,000 km) after the
running in period.
Oil change frequency: check the oil
level from time to time and certainly
before any long journey to avoid the 4
risk of damaging your engine. 1 2
4.4
ENGINE OIL LEVEL: general information (2/2)
B Once the operation is complete, ensure
that the dipstick is fully inserted, or Consult your approved Dealer at
the cap-type dipstick screwed in com- once if you notice an abnormal or
A pletely. repeated drop in any of the fluid
levels.
C
4.5
ENGINE OIL LEVEL: topping up/filling (1/2)
2 2
2.5 16V 2.0 dCi
4.6
ENGINE OIL LEVEL: topping up/filling (2/2)
Oil change Filling: take care when
Service interval: refer to the topping up the oil that
Maintenance Service Booklet for your no oil drips onto engine
vehicle. components - risk of fire.
Remember to refit the cap securely
Average capacities for oil change as there is a risk of fire if oil splashes
including oil filter onto hot engine components.
(for information)
2.5 16V engine: 5.1 liters
2.0 dCi engine: 7.4 liters
4.7
LEVELS (1/3)
Checking intervals Replacement intervals
Check the coolant level regularly Refer to the Maintenance Service
(very severe damage is likely to be Booklet for your vehicle.
caused to the engine if it runs out of
coolant).
If the level needs to be topped up, only
use products approved by our Technical
Department which ensure:
1 protection against freezing;
anticorrosion protection of the cool-
ing system.
Coolant
With the engine switched off and on
level ground, the level when cold must
be between the MIN and MAX
marks on coolant reservoir1.
Top this level up when cold before the
MIN mark is reached.
No operations should be
carried out on the cooling
circuit when the engine is
Consult your approved dealer at hot.
once if you notice an abnormal or Risk of burns.
repeated drop in any of the fluid
levels.
4.8
LEVELS (2/3)
Level2 Topping up
It is normal for the level to drop as After any operation on the hydraulic cir-
2 the linings become worn, but it should cuit, a specialist must replace the fluid.
never drop below the MIN warning Only use fluids approved by our
line. Technical Department (and taken from
If you wish to check the disc and drum a sealed container).
wear yourself, you should obtain the
document explaining the checking pro- Replacement intervals
cedure from our network or from the Refer to the Maintenance Service
manufacturers website. Booklet for your vehicle.
4.9
LEVELS (3/3)/FILTERS
Liquid Filters
Screen wash product (product with an- The replacement of filter elements (air
tifreeze in winter). filter, passenger compartment filter,
diesel filter, etc.) is scheduled in the
Jets maintenance operations for your vehi-
Use a tool such as a needle to adjust cle.
3 the height of the windscreen washer Replacement intervals for filter el-
jets. ements: refer to the Maintenance
Service Booklet for your vehicle.
Windscreen/headlight washer
reservoir
Topping up
Open cap3, fill until you can see the
fluid, then refit the cap.
4.10
Tyre pressure
B C D
E F
4.11
BATTERY
Replacing the battery A 1 2 3
As this operation is complex, we advise
you to contact an approved Dealer.
6 5 4
The battery does not require any main- LabelA
tenance. Observe the indications on the battery:
1 n
aked flames and smoking are for-
bidden;
2 eye protection required;
Handle the battery with care 3 keep away from children;
as it contains sulphuric acid, 4 explosive materials;
which must not come into 5 refer to the instructions;
contact with eyes or skin. If As the battery is specific 6 corrosive materials.
it does, wash the affected area with to the vehicle (presence of
plenty of cold water. If necessary, a ventilation pipe to expel
consult a doctor. corrosive and explosive
gases), make sure that it is replaced The engine may be hot
Ensure that naked flames, red hot with a battery that enables this pipe
objects and sparks do not come into during operations in close
to be connected. Consult an ap- proximity. In addition, the
contact with the battery as there is a proved Dealer.
risk of explosion. engine cooling fan may
start at any moment.
Risk of injury.
4.12
Bodywork maintenance (1/2)
A well-maintained vehicle will last for minor impacts Allow rust to form following minor im-
longer. It is therefore recommended to You should take a minimum number of pacts.
regularly maintain the vehicle exterior precautions in order to safeguard your Use solvents not approved by our
vehicle against such risks and not to Technical Department to remove
Protection against the effects lose the benefit of your vehicles anti- stains as this could damage the
of corrosive agents corrosion protection. paintwork.
Although your vehicle has been treated Drive frequently in snow or muddy
with very effective anti-corrosion prod- What you should not do conditions without washing the ve-
ucts, it nevertheless remains subject to hicle, particularly under the wheel
the effects of: Degrease or clean mechanical com- arches and body.
ponents (e.g. the engine compart-
corrosives in the atmosphere ment), underneath the body, parts
atmospheric pollution (urban and with hinges (e.g. inside the fuel tank
industrial areas), flap) and painted plastic external
fittings (e.g. bumpers) using high-
saline atmospheres (near the pressure cleaning equipment or by
sea, particularly in hot weather), spraying on products not approved
seasonal and damp climatic con- by our Technical Department. If ade-
ditions, (e.g.: road salt in winter, quate precautions are not taken, this
water from road cleaners, etc.). could give rise to corrosion or opera-
tional faults.
abrasives
Wind-borne dust and sand, mud, Wash the vehicle in bright sunlight or
road grit thrown up by other vehi- freezing temperatures.
cles, etc. Scrape off mud or dirt without
prewetting.
Allow dirt to accumulate.
4.13
Bodywork maintenance (2/2)
You should Wash your car frequently, with the Before going through a roller type car
engine off, with cleaning products wash, return the windscreen wiper
Observe the vehicle stopping dis- recommended by our Technical stalk to the Park position (refer to
tances when driving on gravelled Department (never use abrasive the information on the Windscreen
surfaces to prevent paint damage. products) and be sure to jet-rinse off: wash/wipe in Section 1). Check the
Repair, or have repaired quickly, spots of tree resin and industrial mounting of external accessories,
areas where the paint has been grime; additional lights and mirrors, and
damaged, to prevent corrosion ensure that the wiper blades are se-
spreading. bird droppings, which cause cured with adhesive tape.
a chemical reaction with the
Remember to visit the body shop paint that rapidly discolours Remove the radio aerial mast if your
periodically if your vehicle has an paintwork and may even cause vehicle is fitted with this equipment.
anti-corrosion warranty. Refer to the the paint to peel off; Remember to remove the tape and
Maintenance Service Booklet. refit the antenna after washing.
Wash the vehicle immediately to
Respect local regulations about remove these marks since it is im- Spray mechanical components,
washing vehicles (e.g. do not wash possible to remove them by pol- hinges, etc. with products approved
your vehicle on a public highway). ishing; by our Technical Department to
salt, particularly in the wheel protect them after they have been
arches and underneath the body cleaned.
after driving in areas where the
roads have been gritted;
mud in the wheel arches and un-
derneath the body which forms
damp patches.
4.14
INTERIOR TRIM MAINTENANCE (1/2)
A well-maintained vehicle will last Glass instrument panel Textiles (seats, door trim, etc)
longer. It is therefore recommended to (e.g. instrument panel, clock, exterior
maintain the interior of the vehicle regu- Vacuum-clean the textiles regularly.
temperature display, radio display, etc.)
larly. Liquid stain
Use a soft cloth (or cotton wool).
A stain should always be dealt with If this does not clean it properly, use a Use soapy water.
swiftly. soft cloth (or cotton wool) slightly mois-
tened with soapy water and then wipe Dab lightly (never rub) with a soft cloth,
Whatever type of stain is on the trim, rinse and remove the excess.
use cold (or warm) soapy water with clean with a soft damp cloth or cotton
natural soap. wool.
Finally, carefully dry off with a soft dry Solid or pasty stain
Detergents (washing-up liquid, pow- cloth. Carefully remove the excess solid or
dered products, alcohol-based prod- pasty material immediately with a
ucts) should not be used. Cleaning products containing alco-
hol must not be used under any cir- spatula (working from the edges to the
Use a soft cloth. cumstances. centre to avoid spreading the stain).
Clean as for a liquid stain.
Rinse and soak up the excess.
Special instructions for sweets or
Seat belts chewing gum: put an ice cube on the
These must be kept clean. stain to solidify it then proceed as for a
Use products selected by our Technical solid stain.
Department (Approved outlets) or
warm, soapy water and a sponge and
wipe with a dry cloth.
Detergents or dyes must not be used
under any circumstances.
4.15
INTERIOR TRIM MAINTENANCE (2/2)
Removal/replacing removable You should not:
equipment originally fitted in You are strongly advised not to po-
the vehicle sition objects such as deodorants,
If you need to remove equipment in scents, etc. near air vents, as this could
order to clean the passenger com- damage your dashboard trim.
partment (for example, mats), always
ensure that they are correctly refitted
and are the right way around (the driv-
ers mat should be fitted on the drivers
side, etc.) and fit them with the compo-
nents supplied with the equipment (for
example, the driver mat should always
be fixed using the pre-fitted mounting
components).
With the vehicle stationary, ensure that
nothing will impede driving (anything
obstructing the pedals, heel wedged by
the mat, etc.).
4.16
Section 5: Practical advice
Puncture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2
Emergency spare wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2
Tool kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.3
Changing a wheel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.4
Tyres (tyre and wheel safety, use in winter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.6
Headlights (changing bulbs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.9
Rear lights and side lights (changing bulbs). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.12
Interior lights (changing bulbs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.15
Fuses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.18
Battery: troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.20
RENAULT card: battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.22
Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.23
Wipers (replacing blades). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.24
Towing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.25
Operating faults. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.29
5.1
Puncture, emergency spare wheel
2
1
Vehicles fitted with an
3 emergency spare wheel
smaller than the four
6 other wheels:
5 Never fit more than one emer-
gency spare wheel to the same
vehicle.
Replace the emergency spare
wheel as soon as possible with a
4 wheel with the same dimensions
7 as the original.
When this is fitted to the vehicle,
Emergency spare wheel6 Special note which must only be a temporary
This is located in the luggage compart- The tyre pressure monitor does not measure, the driving speed must
ment. To access it: check the emergency spare wheel not exceed the speed indicated
(the wheel replaced by the emergency on the label on the wheel.
Open the tailgate, lift the floor spare wheel disappears from the instru- Fitting an emergency spare
carpet 1, attach the strap3 to the ment panel display). wheel may alter the way the ve-
hook2 then remove the cover4; Refer to the information on the Tyre hicle usually runs. Avoid sudden
unscrew mounting5 by turning it an- pressure monitor in Section 2. acceleration or deceleration and
ticlockwise and remove it; reduce your speed when corner-
ing.
if the vehicle is fitted with speaker7, If snow chains must be used, fit
remove the adhesive tape then place the emergency spare wheel on
it to the side; If the emergency spare the rear axle in order to have a
remove the emergency spare wheel has been stored normal size wheel at the front
wheel6. for several years, have it then check the tyre pressure.
checked by your Dealer to
ensure that it is safe to use.
5.2
TOOL KIT
Jack1
1 Fold the jack away correctly before
storing it in its housing.
Jack handle2
2
Towing hitch3
Refer to the information on Towing in
Section 5.
3
Wheelbrace4
Allows the wheel bolts to be locked/un-
4 locked.
Note: depending on the vehicle, tools2
and4 are stored in a bag.
Do not leave the tools unsecured inside the vehicle as they may come
loose under braking. After use, check that all the tools are correctly
clipped into the tool kit, then position it correctly in its housing: there is a
risk of injury.
If wheel bolts are supplied in the tool kit, only use these bolts for the emergency
spare wheel: refer to the label affixed to the emergency spare wheel.
The jack is designed for wheel changing purposes only. Under no circumstances
should it be used for carrying out repairs underneath the vehicle or to gain access
to the underside of the vehicle.
5.3
Changing a wheel (1/2)
Attach the wheelbrace1 and the jack
2 handle6 (in groove5).
Turn the wheelbrace until the wheel lifts
off the ground.
3
4
5
6
1
1
Vehicles equipped with
Switch on the hazard warn- jack, wheelbrace and wheel
ing lights.
wrench
Keep the vehicle away from
traffic and on a level sur- Use the wheelbrace1 to slacken off
the wheel bolts. Fit it so that you press If the vehicle is not equipped with a
face where it will not slip (if neces-
downwards rather than pulling up- jack, wheelbrace or wheel wrench,
sary, place a solid support under the
wards. these can be obtained from an ap-
jack base).
proved dealer.
Apply the parking brake and engage Start cranking up jack4 by hand to
a gear (first or reverse, or P for auto- align the base plate (which should sit
matic transmissions). flat against the ground) and until the
jack head3 is in the centre of mark2.
Ask all the passengers to leave the To prevent any risk of injury
vehicle and keep them away from or damage to the vehi-
traffic. cle, raise the jack until the
wheel you are replacing is
a maximum of 3 centimetres off the
ground.
5.4
Changing a wheel (2/2)
Undo the bolts and take off the wheel.
Fit the emergency spare wheel on the
central hub and turn it to locate the
mounting holes in the wheel and the
hub.
If bolts are supplied with the emergency
spare wheel, only use these bolts for
the emergency spare wheel. Tighten
the bolts, checking that the wheel is
correctly positioned on its hub and
lower the jack.
With the wheel on the ground, tighten
the screws as fully as possible and
check the tightness as soon as possi-
ble (tightening torque 108 N.m).
Anti-theft bolt
If you use anti-theft bolts, fit these
nearest the valve (wheel embel-
lisher may not be able to fit).
5.5
Tyres (1/3)
Tyre and wheel safety When the tyre tread has been worn to
1 the level of the wear indicators, they
The tyres are the only contact between become visible2: it is then neces-
the vehicle and the road, so it is essen- sary to replace your tyres because the
tial to keep them in good condition. tread rubber is 1.6 mm deep at most,
You must make sure that your tyres resulting in poor roadholding on wet
conform to local road traffic regulations. roads.
An overloaded vehicle, long journeys
by motorway, particularly in very hot
weather, or continual driving on poorly
surfaced minor roads will lead to more
2 rapid tyre wear and affect safety.
5.6
Tyres (2/3)
Tyre pressures Pressures should be checked when the Emergency spare wheel
Adhere to the tyre pressures (including tyres are cold; ignore higher pressures
which may be reached in hot weather Refer to the information on the
the emergency spare wheel). The tyre Emergency spare wheel and in-
pressures should be checked at least or following a fast journey.
structions on Changing a wheel in
once a month and additionally before If tyre pressures cannot be checked Section5.
any long journey (refer to the label af- when the tyres are cold, the normal
fixed to the edge of the drivers door). pressures must be increased by 0.2 to
0.3 bar (or 3 PSI). Changing wheels around
Never deflate a hot tyre.
Special note
Depending on the vehicle, there may
be an adapter which needs to be posi-
Incorrect tyre pressures tioned on the valve before air is added. Vehicles fitted with the
lead to abnormal tyre wear tyre pressure monitors
and unusually hot running. The tyre pressure moni-
These are factors which tor takes around 8 min-
may seriously affect safety and lead utes to identify that tyres have been
to: swapped or replaced. The system
poor road holding, will not operate during this time.
risk of bursting or tread separa- While the tyre pressure monitor is
tion. identifying the tyres which have
The pressure depends on the load Please be aware that a been replaced, the information sent
and the speed of use. Adjust the poorly tightened or miss- by the system may be inaccurate
pressures according to the condi- ing valve cap can make the and this could have serious conse-
tions of use (refer to the information tyres less airtight and lead quences.
on Tyre pressures). to pressure loss.
Always use valve caps identical to
those fitted originally and tighten
them fully.
5.7
Tyres (3/3)
Fitting new tyres Use in winter Studded tyres
Always ensure tyres with identi- Chains This type of equipment may only be
cal specifications are fitted to all four used for a limited period and as laid
For safety reasons, fitting snow down by local legislation. It is neces-
wheels (brand, size, structure, wear chains to the rear axle is strictly for-
etc.). Fitting tyres of different sizes to sary to observe the speed specified by
bidden. current legislation.
the front and rear wheels and/or left Chains cannot be fitted to tyres which
and right wheels may have serious are larger than those originally fitted to These tyres must, at a minimum, be
consequences for the tyres, gearbox, the vehicle. fitted to the two front wheels.
transfer gearbox and the rear differen-
tial pinions. Snow or Winter tyres
We would recommend that these be
fitted to all four wheels to ensure that
your vehicle retains maximum adhe-
For safety reasons, this op- sion.
eration must be carried out Warning: These tyres sometimes have
by a specialist. a specific direction of rotation and a
Fitting different tyres may maximum speed index which may be
change your vehicle as follows: lower than the maximum speed of your
it may mean that your vehicle no vehicle.
longer conforms to current regu-
lations;
it may change the way it handles
when cornering;
it may cause the steering to be Chains may only be fitted
heavy; to tyres of the same size
It may affect the use of snow as those originally fitted to
chains. your vehicle.
5.8
Halogen headlights: changing bulbs
Direction indicator lights
Undo bulb holder1 a quarter of a turn.
1
Undo the bulb a quarter of a turn.
2
Bulb type: PY21W.
3
B Front side light
A Disconnect the bulb holder6 then
4 remove the bulb.
6 5
Bulb type: W5W.
5.9
XENON HEADLIGHTS: changing bulbs
Cleaning the headlights
As the headlights are made of plastic
1 glass, use a soft cloth or cotton wool
to clean them. If this does not clean it
2 properly, moisten the cloth with soapy
water, then wipe clean with a soft damp
cloth or cotton wool.
B B Finally, carefully dry off with a soft dry
A cloth.
Cleaning products containing alco-
4 3 hol must not be used.
5.10
HEADLIGHTS: additional/front fog lights
Additional lights
If you wish to fit fog lights or long range
headlights to your vehicle, consult an
approved dealer.
5.11
REAR LIGHTS AND SIDE LIGHTS: changing bulbs (1/3)
However, because bodywork compo-
nents need to be removed, you are ad-
vised to have your bulbs replaced by
an approved dealer.
4
1 3
2
Side light3
Bulb type: W5W.
When changing the bulb, do
Indicator light4
not touch the electrical cir-
cuit in which the new bulb is Bulb type: PY21W.
to be inserted.
The bulbs are under pres- Brake light5
You could damage the light.
sure and can break when Bulb type: P21W.
replaced.
Risk of injury.
5.12
REAR LIGHTS AND SIDE LIGHTS: changing bulbs (2/3)
6 10
8
7
9 11
Side lights and tailgate Undo bulb holder8 or9 a quarter of a High-level brake light10
reversing light turn then replace the bulb.
Consult an approved Dealer.
Remove the screws7 on the tailgate Note: Ensure that the lead is in place
before removing the light unit6 by before inserting the light unit.
Rear fog light11
pushing it outwards. (depending on vehicle)
Reversing light8
Bulb type: W16W. Consult an approved Dealer.
Side light9
Bulb type: W5W.
5.13
REAR LIGHTS AND SIDE LIGHTS: changing bulbs (3/3)
12
14
13
5.14
INTERIOR LIGHTING: changing bulbs (1/3)
2
1
5.15
INTERIOR LIGHTING: changing bulbs (2/3)
6
4
5.16
INTERIOR LIGHTING: changing bulbs (3/3)
10
5.17
FUSES (1/2)
32119
INCORRECT
1 CORRECT
5.18
FUSES (2/2)
Allocation of fuses (DEPENDING ON THE EQUIPMENT LEVEL)
FRONT
MIRROR
POWER Front lights Heated door mirrors
HEATER
SOCKET Some accessories are protected by
fuses located in the engine compart-
CIGAR BOSE ment in fuse boxA.
Cigar lighter Audio system
LIGHTER AMP However, because of their reduced ac-
cessibility, we advise you to have your
AUDIO Audio system and elec- STOP fuses replaced by an approved Dealer.
Brake lights
MIRROR tric rear-view mirrors LAMP
REAR
ELEC
POWER Rear lights Electrical equipment
B (+)
SOCKET
5.19
Battery: troubleshooting (1/2)
To avoid all risk of sparks
Ensure that any electrical consumers
(courtesy lights, etc.) are switched
off before disconnecting or recon-
necting the battery.
When charging, stop the charger
before connecting or disconnecting
the battery.
Do not place metal objects on the
battery to avoid creating a short cir-
cuit between the terminals.
Always wait at least one minute after
the engine has been switched off Handle the battery with care
before disconnecting a battery. as it contains sulphuric acid,
which must not come into
Make sure that you reconnect the contact with eyes or skin. If
battery terminals after refitting. it does, wash the affected area with
plenty of cold water. If necessary,
consult a doctor.
Ensure that naked flames, red hot
objects and sparks do not come into
contact with the battery as there is a
risk of explosion.
The engine may be hot when car-
rying out operations in close prox-
imity. In addition, the engine cooling
fan can come on at any moment.
Risk of injury.
5.20
Battery: troubleshooting (2/2)
Starting the vehicle using the Attach the positive leadA to the (+) ter-
1 battery from another vehicle minal1 then to the (+) terminal4 of
2 the battery supplying the current.
If you have to use the battery from an-
other vehicle to start, obtain suitable Connect the negative cable B to the
jump leads (with a large cross section) ()3 terminal of the battery supplying
from an approved dealer or, if you al- the current and then to the ()2 termi-
A ready have jump leads, ensure that nal of the discharged battery.
B they are in perfect condition. Check that there is no contact between
The two batteries must have an iden- leadsA andB and that the positive
4 leadA is not touching any metal parts
tical nominal voltage of 12 volts. The
battery supplying the current should on the vehicle supplying the current.
3
have a capacity (amp-hours, Ah) which Start the engine as you would nor-
is at least the same as that of the dis- mally. As soon as it starts, disconnect
charged battery. cablesA andB in reverse order (2 -3
Ensure that there is no risk of contact -4 -1).
Connecting a battery charger between the two vehicles (risk of short
The battery charger must be com- circuiting when the positive terminals
patible with a battery with nominal are connected) and that the discharged
voltage of 12 volts. battery is properly connected. Switch
Switch the engine off and then discon- off your vehicle ignition.
nect both battery leads starting with Start the engine of the vehicle supply- Special procedures may be
the negative terminal. ing the current and run it at an interme- required to charge some
Do not disconnect the battery when the diate engine speed. batteries. Contact your ap-
engine is running. Follow the instruc- proved dealer.
tions given by the manufacturer of Avoid all risk of sparks which may
the battery charger you are using. cause an immediate explosion, and
charge the battery in a well-venti-
lated area. Risk of serious injury.
5.21
RENAULT card: battery
2 A
B
4
1 3
Replacing the battery When refitting, proceed in the reverse Operating faults
When the message Low card battery order, then press one of the buttons on If the battery is too weak to ensure cor-
appears on the instrument panel, re- the card four times, close to the vehicle: rect operation, you may start (insert the
place the RENAULTcard battery, press the next time the vehicle is started, the RENAULT card in the card reader) and
button1, pulling on emergency key2, message will disappear. lock/unlock the vehicle (refer to the in-
then unclip cover3 using tab4. Note: it is not advisable to touch the formation on Locking/unlocking the
Remove the battery by pressing on one electronic circuit or contacts on the doors in Section 1).
side (movementA) and by lifting the RENAULT card when replacing the bat-
other (movementB) then replace it, en- tery.
suring the polarity and model, shown
on cover3 are respected.
5.22
ACCESSORIES
5.23
WIPER BLADES
1
Check the condition of the wiper
B blades. You are responsible for their
4 service life:
2 clean the blades, windscreen and
C rear screen regularly with soapy
A water;
do not use them when the wind-
screen or rear screen are dry;
3
5 free them from the windscreen or
rear screen when they have not
been used for a long time.
5.24
Towing: breakdown (1/4)
Towing procedure Press the Start/Stop button twice in
succession to switch off the ignition
Before any towing, check that the steer- once towing is finished (risk of running
ing column is not locked. down the battery).
If it is locked, insert the RENAULT card Furthermore, it is essential to respect
into the reader and press the Start/Stop the towing regulations set out in the leg-
button twice without pressing on the islation of the country concerned and, if
pedals. The steering column unlocks, your vehicle is the towing vehicle, not to
the vehicle accessory functions are exceed the towing weight of your vehi-
supplied with power and you can use cle. Contact your approved Dealer.
the lights (stop lights, directional indica-
tor lights, etc.): the vehicle must have
its lights on at night.
Do not remove the RENAULT card from
the reader when the vehicle is being
towed.
5.25
Towing: breakdown (2/4)
32188
32187
1
2WD vehicles
Vehicles fitted with an automatic If the lever is stuck in P,
transmission or continuously vari- even though you are de-
able transmission. pressing the brake pedal,
With the ignition off, the gearbox is no the lever can be released
longer lubricated. If it is not, the vehi- manually.
cle must be transported on a trailer or To do this, first remove the cover2
be towed with the front wheels off the on the left-hand side of the gear
ground. lever.
While depressing the brake pedal,
shift the gear lever into neutral(N)
and simultaneously press the
button1 on the lever and on the
button under the cover2.
5.26
Towing: breakdown (3/4)
32185
32186
4WD vehicles
Whichever type of gearbox is fitted, a
4WD vehicle must never be towed if
any of its 4 wheels are touching the
ground.
5.27
Towing: breakdown (4/4)
RENAULT recommends
the use of a rigid towing bar.
If a rope or cable is used
(where the law allows this),
the vehicle being towed must be
1 able to brake.
A vehicle must not be towed if it is
not fit to be driven.
Do not accelerate or brake sud-
3 2 denly when towing, as this may
result in damage being caused to
4 the vehicle.
When towing a vehicle, it is ad-
visable not to exceed 15mph
Only use the front towing point1 and Using the towing hitch (25km/h).
the rear towing point4 (never use the
driveshafts). These towing points may Remove cover2.
only be used for towing: never use Screw in towing hitch3 as far as
them for lifting the vehicle directly or in- possible. To do this, insert the towing
directly. hitch3 and screw it in by hand, then
tighten it using the wheelbrace.
The towing hitch3 and the wheelbrace
are located in the tool kit in the luggage
compartment (refer to information con-
cerning the tool kit in Section 5).
5.28
Operating faults (1/5)
The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact
an approved Dealer as soon as possible.
The RENAULT card does not lock or Card battery is flat. Replace the battery. You can still lock/
unlock the doors. unlock and start your vehicle (refer to the
information on Locking/unlocking the
doors in Section 1 and Starting/Stopping
the engine in Section 2).
Use of appliances operating on the Stop using the equipment or use the
same frequency as the card (mobile emergency key (refer to the informa-
phone, etc.). tion on Locking/unlocking the doors in
Section1).
Vehicle located in a high electromag- Use the emergency key integrated in the
netic radiation zone. card (refer to the information on Locking/
Vehicle battery flat. unlocking the doors in Section 1).
5.29
Operating faults (2/5)
The starter is activated POSSIBLE CAUSES WHAT TO DO
The instrument panel indicator lights Battery terminals not tight, Retighten or reconnect the terminals, or clean
are weak or fail to light up and the battery terminals discon- them if they are oxidised.
starter does not turn. nected or oxidised.
The engine will not start. Starting conditions are not Refer to the information on Starting/stopping the
fulfilled. engine in Section 2.
The RENAULT hands-free Insert the card in the card reader in order to start
card does not work. the engine.
Refer to the information on Starting/stopping the
engine in Section 2.
The engine cannot be switched off. Card not detected. Insert the card in card reader.
The steering column remains locked. Steering wheel locked. Move the steering wheel while pressing the engine
start button (refer to the information on Starting
the engine in Section 2).
5.30
Operating faults (3/5)
Vibrations. Tyres not inflated to correct pres- Check the tyre pressures: if this is not the
sures, incorrectly balanced or dam- problem, have them checked by an ap-
aged. proved Dealer.
White smoke from the exhaust. This is not necessarily a fault. Smoke Refer to the information on Special fea-
may be caused by regeneration of the tures of diesel versions in Section 2.
particle filter.
Smoke under the bonnet. Short-circuit or cooling system leak. Stop, switch off the ignition, stand away
from the vehicle and contact an approved
dealer.
while cornering or braking The level is too low. Top up the engine oil (refer to the informa-
tion on Engine oil level Topping up/refill-
ing in Section 4).
is slow to go out or remains lit Loss of oil pressure. Stop the vehicle: contact an authorised
under acceleration dealer.
5.31
Operating faults (4/5)
The engine is overheating. The cool- Engine cooling fan not working. Stop the vehicle, switch off the engine and
ant temperature indicator is in the contact an approved dealer.
warning zone and warning light
comes on.
Radiator: If there is a significant lack of coolant, remember that it must never be topped up using cold coolant while
the engine is very warm. After any procedure on the vehicle which has involved even partial draining of the cooling
system, it must be refilled with a new mixture prepared in the correct proportions. Reminder: only products approved
by our Technical Department may be used for this purpose.
5.32
Operating faults (5/5)
Electrical equipment POSSIBLE CAUSES WHAT TO DO
The wipers do not work. Wiper blades stuck. Free the blades before using the wipers.
Direction indicators flashing more Blown bulb. See information on Headlights: changing
quickly. the bulbs or Rear lights: changing the
bulbs in section 5.
The direction indicators do not work. Faulty electrical circuit. Consult an approved dealer.
The lights do not come on or go off. Faulty electrical circuit or control. Consult an approved dealer.
The illumination of the seat belt re- An object is stuck between the floor Remove any objects from underneath the
minder warning light does not match and the seat and is disrupting the op- rear seats.
the seat belt status. eration of the sensor.
5.33
5.34
Section 6: Technical specifications
A 6
7
8
9
10
1
2
3
4
5 11
12
A 13
The information shown on the ve- 6 Technical specifications of vehicle.
hicle identification plate should be 7 Vehicle paint reference.
quoted on all correspondence or 8 Equipment level.
orders. 9 Vehicle type.
10 Trim code.
Vehicle identification plateA 11 Additional equipment specifica-
1 Vehicle type and chassis number. tion.
Depending on the vehicle, this 12 Fabrication number.
B information is also given on 13 Interior trim code.
markingB.
2 Maximum permissible all-up
weight.
3 Total train weight (vehicle fully
loaded, with trailer).
4 Maximum permissible all-up
weight.
5 Rear axle maximum permissible
all-up weight.
6.2
Engine identification plates
B
B
6.3
DIMENSIONS (in metres)
1.695 (1)
1.715 (2)
1.550
(1) without roof rack 2.120
(2) with roof rack
6.4
ENGINE SPECIFICATIONS
Engine type
2TR M9R Turbo
(see engine number)
6.5
WEIGHTS (in kg)
The weights indicated are those of a basic model without options: they will vary depending on the equipment level of
your vehicle. Consult an authorised dealer.
Maximum permissible all-up weight (MMAC) Weights indicated on the manufacturers plate
Total train weight (MTR) (refer to Section 6 Vehicle identification plate)
Permissible load on the roof with the carrying device 85 kg (including the carrying device)
6.6
Replacement parts and repairs
Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same
level of quality as the parts fitted originally.
If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out
within the manufacturers Network using original parts are guaranteed according to the conditions set out on the reverse of the
repair order.
6.7
service sheets (1/6)
VIN: ..................................................................................
6.8
service sheets (2/6)
VIN: ..................................................................................
6.9
service sheets (3/6)
VIN: ..................................................................................
6.10
service sheets (4/6)
VIN: ..................................................................................
6.11
service sheets (5/6)
VIN: ..................................................................................
6.12
service sheets (6/6)
VIN: ..................................................................................
6.13
Anticorrosion check (1/5)
If the continuation of the warranty is subject to repair, it is indicated below.
VIN: ..........................................................
Date of repair:
Date of repair:
Date of repair:
6.14
Anticorrosion check (2/5)
If the continuation of the warranty is subject to repair, it is indicated below.
VIN: ..........................................................
Date of repair:
Date of repair:
Date of repair:
6.15
Anticorrosion check (3/5)
If the continuation of the warranty is subject to repair, it is indicated below.
VIN: ..........................................................
Date of repair:
Date of repair:
Date of repair:
6.16
Anticorrosion check (4/5)
If the continuation of the warranty is subject to repair, it is indicated below.
VIN: ..........................................................
Date of repair:
Date of repair:
Date of repair:
6.17
Anticorrosion check (5/5)
If the continuation of the warranty is subject to repair, it is indicated below.
VIN: ..........................................................
Date of repair:
Date of repair:
Date of repair:
6.18
Alphabetical index (1/5)
A C
ABS........................................................................2.242.28 catalytic converter......................................................... 2.6, 2.8
accessories........................................................................ 5.23 central door locking.........................................1.8, 1.111.13
accessories socket............................................................. 3.28 changing a bulb........................................................5.95.14
additional methods of restraint........................................... 1.28 changing a wheel........................................................ 5.45.5
side protection.............................................................. 1.27 changing gear..................................................2.9, 2.382.40
to the front seat belts........................................1.221.25 child minder mirror.............................................................. 3.19
to the rear seat belts..................................................... 1.26 child restraint/seat..............................1.291.30, 1.321.36
adjusting your driving position................................. 1.181.19 child safety.....1.21.3, 1.291.30, 1.321.36, 3.143.17
advice on antipollution............................................2.142.16 child seats..........................................1.291.30, 1.321.36
air bag....................................................................1.221.28 children........................................................... 1.291.30, 1.30
activating the front passenger air bags......................... 1.39 children (safety)......................................1.21.3, 3.143.17
deactivating the front passenger air bags..................... 1.37 cigar lighter......................................................................... 3.28
air conditioning.........................................................3.43.13 clock................................................................................... 1.60
air vents....................................................................... 3.23.3 closing the doors......................................................1.91.12
all-wheel drive system............................................2.212.23 continuous variation...............................................2.382.40
anti-corrosion check...............................................6.146.18 continuously variable transmission.........................2.382.40
anti-corrosion protection.......................................... 4.134.14 control instruments.................................................1.481.59
anti-lock braking system: ABS................................2.242.28 controls.................................................................... 1.401.41
antipollution coolant......................................................................... 1.48, 4.8
advice........................................................................... 2.14 courtesy light......................................3.203.21, 5.155.17
armrest: courtesy mirrors.................................................................. 3.18
front............................................................................... 3.23 cruise control..........................................................2.292.35
rear............................................................................... 3.24 cruise control-speed limiter....................................2.292.35
ashtray................................................................................ 3.28
automatic gearbox (use).........................................2.382.40 D
automatic gearbox selector lever...........................2.382.40 dashboard............................................................... 1.401.41
deadlocking the doors.......................................................... 1.8
B dimensions........................................................................... 6.4
battery................................................................................ 4.12 display....................................................................1.441.49
troubleshooting.................................................. 5.205.21 doors................................................................ 1.91.10, 1.13
bonnet......................................................................... 4.24.3 doors/tailgate........................................................................ 1.8
brake fluid............................................................................. 4.9 downhill speed control........................................................ 2.27
bulbs drivers position..................................1.401.41, 1.441.47
changing.............................................................5.95.14 driving................................................. 2.22.16, 2.182.40
7.1
Alphabetical index (2/5)
driving position front seats
settings.............................................................. 1.181.19 adjustment................................................ 1.14, 1.161.17
fuel
E advice on fuel economy................................................ 2.14
electric beam height adjustment......................................... 1.67 capacity.............................................................1.711.73
electric windows...................................................... 3.143.15 filling.........................................................1.46, 1.711.73
electronic parking brake.........................................2.102.13 grade.................................................................1.711.73
Electronic Stability Program: ESP..........................2.242.28 fuel economy..........................................................2.142.16
emergency key............................................................ 1.21.3 fuel filler cap...........................................................1.711.73
emergency spare wheel.............................................. 5.25.3 fuel level............................................................................. 1.48
engine fuel priming bulb.......................................................... 1.73, 2.8
technical specifications................................................... 6.5 fuel repriming...................................................................... 1.73
engine oil....................................................................4.54.7 fuel tank
engine oil level.................................................................... 1.49 capacity.............................................................1.711.73
engine specifications............................................................ 6.5 fuel tank capacity....................................................1.711.73
engine start/stop button............................................... 2.32.4 fuses........................................................................ 5.185.19
environment........................................................................ 2.17
ESP: Electronic Stability Program..........................2.242.28 G
external lights and signals.................................................. 1.67 gear lever............................................................................. 2.9
glove box............................................................................ 3.22
F
4 wheel drive (4WD)...............................................2.212.23 H
faults handbrake............................................................................ 2.9
operating faults.................................................5.295.33 hands-free telephone integrated control............................. 3.37
filter hazard warning lights signal...................................1.631.66
air filter.......................................................................... 4.10 headlight beam adjustment................................................ 1.67
diesel filter..................................................................... 4.10 headlight flashers............................................................... 1.63
particle filter........................................................... 1.46, 2.8 headrest.................................................................. 1.141.15
passenger compartment filter....................................... 4.10 heating and air conditioning system.........................3.73.13
fittings.....................................................................3.223.27 heating system.........................................................3.43.12
fog lights............................................................................. 5.11 hill start............................................................................... 2.28
front passenger air bag deactivation.................................. 1.37 Hill Start Assistance (HSA)................................................. 2.28
front seat adjustment horn.................................................................................... 1.63
electric controls............................................................. 1.16 horn:
manual controls................................................. 1.161.17 flash.............................................................................. 1.63
sounding the horn......................................................... 1.63
7.2
Alphabetical index (3/5)
I direction indicators........................................ 1.63, 5.9, 5.12
indicators.............................................................................. 5.9 fog lights.............................................................. 1.66, 5.11
indicators: hazard warning............................................................. 1.63
exterior temperature indicator....................................... 1.60 main beam headlights..................................................... 5.9
instrument panel...............................................1.441.59 number plate lights....................................................... 5.14
instrument panel............................... 1.441.59, 1.641.66 reversing lights.............................................................. 5.13
instrument panel messages...................................1.521.59 side lights...............................1.641.66, 5.9, 5.125.13
interior trim lights-on warning buzzer.................................................... 1.65
maintenance...................................................... 4.154.16 locking the doors.............................................1.21.10, 1.13
luggage compartment cover............................................... 3.33
J luggage retaining net.......................................................... 3.35
jack.............................................................................5.35.5
M
L maintenance:
levels: bodywork........................................................... 4.134.14
brake fluid....................................................................... 4.9 interior trim......................................................... 4.154.16
coolant............................................................................ 4.8 mechanical........................................ 4.24.5, 6.86.13
engine oil..............................................................4.54.7 mileage before service........................................6.86.13
windscreen washer reservoir........................................ 4.10 map reading lights................................................... 3.203.21
lifting the vehicle methods of restraint in addition to the seat belts....1.261.28
changing a wheel................................................... 5.45.5 multimedia equipment........................................................ 3.37
lighting:
exterior..............................................................1.641.66 N
instrument panel...............................................1.641.66 navigation........................................................................... 3.37
interior...........................................3.203.21, 5.155.17 navigation system............................................................... 3.37
lights
additional...................................................................... 5.11 O
adjustment.................................................................... 1.67 oil change............................................................................. 4.7
changing bulbs..................................................... 5.95.10 opening the doors.....................................................1.91.12
fog lights....................................................................... 5.11 operating faults.......................................................5.295.33
front................................................................................. 5.9
mobile directional.......................................................... 1.65 P
lights: paintwork
adjustment of headlight beam height............................ 1.67 maintenance...................................................... 4.134.14
brake lights.......................................................... 5.12, 5.14 reference......................................................................... 6.2
dipped beam headlights.............................1.641.66, 5.9 parking distance control.......................................... 2.362.37
7.3
Alphabetical index (4/5)
power-assisted steering..................................................... 1.61 signals and lights....................................................1.641.66
puncture.....................................................................5.25.5 special features of diesel versions.............................. 2.72.8
special features of petrol vehicles........................................ 2.6
R speed limiter...........................................................2.292.31
radio................................................................................... 3.37 starting the engine....................................................... 2.32.4
rear bench seat....................................................... 3.293.30 steering wheel
rear parcel shelf.................................................................. 3.33 adjustment.................................................................... 1.61
rear screen de-icing/demisting.................................... 3.6, 3.10 stopping the engine.............................................................. 2.5
rear seats storage compartment.............................................3.223.27
functions............................................................ 3.293.30 storage compartments............................................3.223.27
rear view mirrors................................................................. 1.62 sun visor............................................................................. 3.18
RENAULT ANTI-INTRUDER DEVICE (RAID).................... 1.13 sunroof.................................................................... 3.163.17
RENAULT card
battery........................................................................... 5.22 T
use........................................................................1.21.8 tailgate............................................................ 3.313.32, 3.34
RENAULT card battery....................................................... 5.22 tanks and reservoirs
replacement parts................................................................. 6.7 brake fluid....................................................................... 4.9
reverse gear coolant............................................................................ 4.8
selecting.....................................................2.9, 2.382.40 tanks and reservoirs:
reversing sensor...................................................... 2.362.37 windscreen washer....................................................... 4.10
roof bars............................................................................. 3.36 technical specifications........................................6.2, 6.46.7
roof rack telephone............................................................................ 3.37
roof bars........................................................................ 3.36 temperature........................................................................ 1.60
running in.............................................................................. 2.2 temperature regulation.............................................3.73.12
tool kit................................................................................... 5.3
S towing
screen wash/wipe.................................................... 1.681.69 breakdown........................................................5.255.28
seat belt pretensioners towing equipment.......................................................... 3.34
front seat belt....................................................1.221.25 towing a caravan......................................................... 3.34, 6.6
seat belts.......................................... 1.181.20, 1.221.25 towing equipment
see-me-home lighting......................................................... 1.65 fitting............................................................................. 3.34
service sheets..........................................................6.86.13 towing hitch............................................................5.255.28
side and number plate lighting towing rings............................................................. 3.343.35
changing bulbs.............................................................. 5.14 towing weights...................................................................... 6.6
side indicator lights transporting children...........................1.291.30, 1.321.36
changing bulbs.............................................................. 5.14
7.4
Alphabetical index (5/5)
transporting objects
in the luggage compartment......................................... 3.34
luggage net................................................................... 3.35
trip computer and warning system... 1.441.47, 1.501.59
tyre pressure..........................................2.182.20, 4.11, 5.7
tyre pressure monitor.............................................2.182.20
tyre pressures..................................................................... 4.11
tyres............................................. 2.182.20, 4.11, 5.65.8
U
unlocking the doors................................................. 1.111.12
V
vehicle identification............................................................. 6.2
vehicle identification plates.......................................... 6.26.3
ventilation...................................................................3.43.6
heating and air conditioning system...................3.73.12
W
warning buzzer............................................................ 1.9, 1.63
warning lights................................... 1.441.47, 1.501.59
washing................................................................... 4.134.14
weights................................................................................. 6.6
wheelbrace........................................................................... 5.3
wheels (safety)...........................................................5.65.8
windows................................................................... 3.143.15
windscreen......................................................................... 3.18
windscreen de-icing/demisting.................................... 3.6, 3.10
windscreen washer........................................1.681.70, 4.10
windscreen washer/wiper................................................... 1.70
wiper blades....................................................................... 5.24
wipers
blades........................................................................... 5.24
7.5
4 SIMPLE ACTIONS*
FOR YOUR SAFETY
1 2 3 4
Always fasten Always secure children Adjust the height of Place heavy objects or
your seat belt, using devices suitable the seat belt according luggage at the back of the
even for short journeys for their size and weight to your size. luggage compartment.
even if your vehicle is (seat, shell seat, etc.).
fitted with air bags. Adjust the angle of your Distribute the load
Important! If the vehicle is seatback ensuring that between the right-hand
Make sure that all fitted with front passenger the seat belt remains in and left-hand sides in
passengers have air bags which can be contact with your body. the loading area when
fastened their seat belts, disconnected, disconnect transporting goods.
even in the back. them before installing a Adjust the height of the
rear-facing baby seat. headrest: headrest
height = top of your head.
Headrest as close as
possible to the head.
* Warning: these actions do not constitute an exhaustive list. Refer to your Drivers Handbook for more information.
( www.e-guide.renault.com )
RENAULT S.A.S. SOCIT PAR ACTIONS SIMPLIFIE AU CAPITAL DE 533 941 113 / 13-15, QUAI LE GALLO
92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 SIRET 780 129 987 03591 / TL. : 0810 40 50 60
NU 830-6 99 91 071 84R 09/2010 Edition anglaise
999107184R CY