Professional Documents
Culture Documents
This standard has been approved for use by agencies of the Department of Defense.
Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
A 423/A 423M 95 (2004)
TABLE 1 Chemical Requirements TABLE 3 Tensile Requirements
Tensile strength, min, ksi [MPa], 60 [415]
Composition, % Yield strength, min, or 50 mm, 37 [255]
Grade 1 Grade 2 ksi [MPa]
Elongation in 2 in. or 50 mm, min, % 25
Carbon, max 0.15 0.15 For longitudinal strip tests a deduction for each 1.25A
Manganese, max 0.55 0.501.00 132 in. [0.8 mm] decrease in wall thickness
Phosphorus 0.060.16 0.04 max below 516 in. [8 mm] from the basic minimum
Sulfur, max 0.060 0.05 elongation of the following percentage points
Silicon, min 0.10 ... shall be made
Copper 0.200.60 0.301.00 A
Chromium 0.241.31 ... Calculated elongation requirements shall be rounded to the nearest whole
Nickel 0.200.70 0.401.10 number.
Molybdenum, min ... 0.10
2
A 423/A 423M 95 (2004)
SUPPLEMENTARY REQUIREMENTS
The following supplementary requirement shall apply only when specified by the purchaser in the
inquiry, contract, or order. Details of this supplemental requirement shall be agreed upon by the
manufacturer and the purchaser.
The following supplementary requirements may become a part of the specification when specified
in the inquiry or invitation to bid, and purchase order or contract. These requirements shall not be
considered unless specified in the order and the necessary tests shall be made at the mill.
S2. Additional Testing of Welded Tubing per ASME S2.3 The test methods described in the supplement may not
Request be capable of inspecting the end portions of tubes. This
S2.1 Each tube shall be subjected to an ultrasonic inspection condition is referred to as end effect. This portion, as deter-
employing Practices E 273 or E 213 with the rejection criteria mined by the manufacturer, shall be removed and discarded.
referenced in Specification A 450/A 450M. S2.4 In addition to the marking prescribed in Specification
S2.2 If Practice E 273 is employed, a 100 % volumetric A 450/A 450M, S2 shall be added after the grade
inspection of the entire length of each tube shall also be designation.
performed using one of the non-destructive electric tests
permitted by Specification A 450/A 450M.
ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned
in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk
of infringement of such rights, are entirely their own responsibility.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and
if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards
and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the
responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should
make your views known to the ASTM Committee on Standards, at the address shown below.
This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,
United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above
address or at 610-832-9585 (phone), 610-832-9555 (fax), or service@astm.org (e-mail); or through the ASTM website
(www.astm.org).