Professional Documents
Culture Documents
Notifier FZM 1 Interface Module PDF
Notifier FZM 1 Interface Module PDF
12 Clintonville Rd
FZM-1 Interface Module Northford, CT 06472-1653
(203) 484-7161
Specifications
Normal Operating Voltage: 15 to 32 VDC
Maximum Current Draw: 5.1 mA (LED on)
Average Operating Current: 270A (LED flashing)
EOL Resistance: 3.9K Ohms
Maximum IDC wiring resistance: 25 Ohms
External Supply Voltage (between Terminals T3 and T4)
DC Voltage: 18-28 volts power limited (19 to 28VDC when used with MTL isolator model MTL3043 in
intrinsically safe applications)
Ripple Voltage: 0.1 Volts RMS maximum
Current: 90mA per module
Temperature Range: 32F to 120F (0C to 49C)
Humidity: 10% to 93% Noncondensing
Dimensions: 41/2 H x 4 W x 11/4 D (Mounts to a 4 square by 21/8 deep box.)
Accessories: SMB500 Electrical Box
Before Installing 1. Install module wiring in accordance with the job draw-
This information is included as a quick reference installa- ings and appropriate wiring diagrams.
tion guide. Refer to the control panel installation manual 2. Set the address on the module per job drawings.
for detailed system information. If the modules will be Note: Some panels support extended addressing. In
installed in an existing operational system, inform the order to set the module above address 99 on compatible
operator and local authority that the system will be tempo- systems, carefully remove the stop on the upper rotary
rarily out of service. Disconnect power to the control panel switch with thumb in the direction shown in Figure 1.
before installing the modules. 3. Secure module to electrical box (supplied by installer),
as shown in Figure 2A.
NOTICE: This manual should be left with the owner/user
of this equipment. Figure 1. Removing
Rotary Switch Stop: 9 67 8 9
0
5 10
General Description 8 4
3
2
11
12
13
1
This module allows intelligent panels to interface and moni- LOOP ADDRESS
Compatibility Requirements
To ensure proper operation, this module shall be connected Figure 2B:
to a compatible Notifier system control panel only (list
available from Notifier).
0
1
2
10
9
11
8
4 6 7 5 1 1 12
4 5 67
3
8 4 3
9
0 4
Mounting
8
1
3
1
0
2
NS 1
2 7 ES
S
TE
DR
10
5
9
11
8
6 AD
4 5 6 7 15 1 1 12
4 5 67
3
8 4 3
9
3
5 ES
2
1
8 4 ON
9
0
2
NS 1
7 ES
S
TE
DR
6 AD
3
S
5
2
1
ONE
Wiring
A78-2611-12
NOTE: All wiring must conform to applicable local codes,
ordinances, and regulations. This module is intend-
ed for power-limited wiring only.
A78-2610-10
N500-49-00 1 I56-1172-06
www.PDF-Zoo.com
Figure 3. Interface two-wire conventional COMMUNICATION LINE CONNECT MODULES TO LISTED
detectors, NFPA Style B: 32 VDC MAX.
TWISTED PAIR
COMPATIBLE CONTROL PANELS ONLY.
IS RECOMMENDED
)( )(
TO NEXT FROM PANEL OR
)+( )+(
DEVICE PREVIOUS DEVICE
9 0
5
67 8 9
10 )(
8 4
3
11
12
1
7
2 13
1 0 15 14 2 )+(
TENS
5
6789 )(
6 4 3
3 )+( LISTED BATTERY-BACKUP SWITCHED
5 2 4
3.9K EOL ONES
10 DC POWER SUPPLY.
LOOP ADDRESS
RESISTOR
(INCLUDED)
A2143-10
+ +
POWER TO THE INTERFACE MODULE
MUST BE EXTERNALLY SWITCHED TO
RESET THE DETECTORS. AN FRM-1
RELAY CONTROL MODULE CAN BE USED TO
SWITCH POWER FROM A STANDARD
DO NOT LOOP WIRE UNDER TERMINALS. BREAK WIRE POWER SUPPLY - SEE FIGURE 5.
RUN TO PROVIDE SUPERVISION OF CONNECTIONS.
OPTIONAL BRANCH CIRCUIT
DETECTORS MUST BE UL LISTED COMPATIBLE WITH MODULE. TO NEXT INTERFACE MODULE.
INSTALL DETECTORS PER MANUFACTURER'S MODULE SUPERVISES SUPPLY
INSTALLATION INSTRUCTIONS. A78-2394-14
VOLTAGE AND DETECTOR LOOP.
DO NOT LOOP WIRE UNDER TERMINALS. BREAK WIRE OPTIONAL BRANCH CIRCUIT
RUN TO PROVIDE SUPERVISION OF CONNECTIONS.
TO NEXT INTERFACE MODULE.
DETECTORS MUST BE UL LISTED COMPATIBLE WITH MODULE. MODULE SUPERVISES SUPPLY
INSTALL DETECTORS PER MANUFACTURER'S VOLTAGE AND DETECTOR LOOP.
INSTALLATION INSTRUCTIONS. A78-2395-14
)( )(
TO NEXT FROM PANEL OR
)+( )+(
DEVICE PREVIOUS DEVICE
INTERFACE
TERMINAL WIRING MUST BE POWER LIMITED. MODULE
9 0
5
67 8 9
10 )(
8 4
3
11
12
1
7
2 13
1 0 15 14 2 )+(
TENS
5
6789 )(
6 4 3
3 )+( LISTED BATTERY-BACKUP SWITCHED
5 2 4
3.9K EOL ONES
10 DC POWER SUPPLY.
LOOP ADDRESS
RESISTOR
(INCLUDED)
A2143-10
+ +
POWER TO THE INTERFACE MODULE
MUST BE EXTERNALLY SWITCHED TO
RESET THE DETECTORS. AN FRM-1
RELAY CONTROL MODULE CAN BE USED TO
SWITCH POWER FROM A STANDARD
MTL3043 ISOLATOR
DO NOT LOOP WIRE UNDER TERMINALS. BREAK WIRE POWER SUPPLY - SEE FIGURE 5.
RUN TO PROVIDE SUPERVISION OF CONNECTIONS.
OPTIONAL BRANCH CIRCUIT
DETECTORS MUST BE UL LISTED COMPATIBLE WITH MODULE. TO NEXT INTERFACE MODULE.
INSTALL DETECTORS PER MANUFACTURER'S MODULE SUPERVISES SUPPLY
INSTALLATION INSTRUCTIONS.
A78-2394-29
VOLTAGE AND DETECTOR LOOP.
N500-49-00 2 I56-1172-06
www.PDF-Zoo.com 2001 Notifier