E orquer|
BULLETIN L-30'31t
VGC-F TYPE
WORM GEAR
VALVE OPERATORS
Hi Outline
Valve Operators Type VG
are worm gear
drives designed for use as manual operators
for 90-degreesrotation valves and various
other devices. They are most suitable for ope-
rating butterfly valves, plug valves, ball valves
and dampers,
Compared with conventional valve actuators,
such as type H-BC, they are designed much
smaller for manual operation. Valve Opera-
tors Type VGC-F are highly reliable and
economical gear drives.
Hi Features
J. They are small but powerful
2. Though their design is simple, they have all necessary mechanisms, and are easy to handle.
3. They are provided with mechanical stops which permit adjustment of the angle within
plus or minus 5 degrees at both ends of the travel.
4, The wormis designed with a self-locking lead angle.
5. Gear backlash is minimized to prevent fluttering.
6. ‘They have a position indicator directly coupled with the drive sleeve.
7. They are of totally-enclosed structure, Weatherproof and are supplied at shipment filled
with grease for long life service without maintenance.
HiSize Type Allowable Torque | Gear Ratio
“| voc - 3F 8Gkg +m 4an1
vec— 8F 207kg +m 95:1
vec —20F 300kg +m Tort +
(With SGA 210: 1)
NIPPGN GEAR CO.,LTD.ulenae
Specification
SA mm (inch)
Type voc -3F Voc ~ aF voc - 20F
i . 386 626 850
eee (1.378) (2.047) (2.559)
0 10x8 15X10 tax 12
: | 0394 x 0.315) (0.591 X 0,394) (0.709 x 0.472)
Max. Travel 90° 90° 90°
Stop Adjustment oe oe 6°
H.W. Turns for 90° 10.5 13.8 WS
Worm Lead Angle Right Right Right
nal,
‘The handwheel is opt
manual operation, please con
Section & Parts
If the valve operators are to be used for any purpose other than
nsult Nippon Gear,
List
VGC-3F, VGC-8F
No. Pans Name Pare Name w|
1 | Housing Worm 1
| 2 | Housing Cover - Worm Shaft 1
3 Pointer Cap Key 1
4 | Worm Gear “Stopper Bolt 2
ls | Lock Bott 2
6
NIPPON GEAR CO, LTD.
1011
FA Dimension
US of ta, =)
M-Depth of Tape
mm (inch)
ataleclole]e]olu]s w es |rcel s
voc-|cr70 fears] oo fue | 5 | us | co | os | ss
3 J 6.03) | c2.r5 | 12.221] 5.4m |02.17 | cas] 2.369] 0.989] 10.22)
o fe] iw |
(1819 | 6.49 | gas) | 2-29
vec-| 25 | ss90] a | no | x | wo | mo | | os
8F | ca.ass| «359 (2.25)] 6.69] 2.76)] (6.50 (2.269] 0.39) 0.39
a
(2.08) (6.69) | 05.50] 46)
Go |g OT act ao] ae wean
sf vee[oed aed vale
3 fes.06| Los oi} (0.20 fier,
= wv] eee | 2 coe
OF Jian am J. 800-40 [0270 | warceam| *? |» man. ciension
Handwheel Dimension
Hi Rotational direction twee | ne | Ho | weight
When the input shaft is
rotated counterclockwise,
the worm wheel rotates
clockwise as viewed from
the upper side of the unit.
37) 308 :
TAY voomar | alia | 2 | va
~A 32 | 308
voc-aF | gw | aa | 42K0
i 37 | 460
VEC~8F | caay | (1a) | 109K
* As VGC-20F is a new type, please inquire with Nippon Gear about its structure and its dimensions.
NIPPON GEAR CG, LTD.bere 2
Binstructions about Handling the Unit (refer to the sketches below)
1. Before shipping, the stopper bolts are adjusted such that the worm wheel rotates 90 degrees.
If it is necessary to readjust ((0) the stopper bolts after installing the unit to the valve, first
adjust the stopper bolts and then lock({1)the lock bolts by applying screw-locking material,
meter of worm wheel and installing the unit to valve.
2. Procedure for machining the inside
VGC-F unit is shipped with the inside diameter of its worm wheel left unmachined. Perform
the machining according to the following procedure without disassembling the unit. The
explanation applies in cases in which the valve opens when the valve stem is rotated clock:
stalled.
wise as viewed from the side on which the unit is
(1)_ Check the position of the key way at the stem end when the valve is fully closed.
inter of the pointer cap to the CLOSE mark of
(2) Rotete the input shaft, and set the p
the scale on the opposite side of the input shaft, And the end of the worm wheel will
touch the stopper bolts at this time.
(3) Remove the pointer cap, and check to see if the mating mark on the worm wheel end
face meets the input shaft side of the mating mark on the housing cover.
(4) Then, machine the inside diameter of the worm wheel and the key way to the valve
stem diameter and the key position. :
(5) Remove by grinding the “CLOSE” position indication not used,
(6) Install the unit to the valve.
(7) When installing the unit, fully close the valve and set the pointer of the unit to the
CLOSE mark of the scale.
Stonper bolt
Leck bort |
3. Rotation direction of the handwheel
‘The rotational directions of the handwheel to be provided as an
optional item are ted by 2 arrows as shown by the sketch. The
arrow indicating the unnecessary direction should be removed by
grinding,
% — The contents of this bulletin are subject to alterations without prior notice.
UNDER LICENSE FROM PHILADELPHIA GEAR CORP/LIMITORQUB CORPORATION U.S.A.
G MPPON GEAR CG, LTD.
iara-cho, Fujisawa City, Kanagawa Pref. Japan
Fujisawa 046645 ~ 2250
TELEX. (NGCFUS J) 47986
3862261 (NGCFUJ 3)
Sales Office: Tokyo Osaka —Nagoya—Fukuoka—Hiroshima
Fujisawa Head Office & Factory:
92 Bs