Professional Documents
Culture Documents
VHF TRANSCEIVER
iV80
iV80E
FEATURES IMPORTANT
Dust-protection/Splash-resistant construc- READ ALL INSTRUCTIONS carefully and completely
tion (IP54*) before using the transceiver.
*Only when the battery pack/case, antenna and jack cover are SAVE THIS INSTRUCTION MANUAL This in-
attached.
struction manual contains important operating instructions
for the IC-V80/V80E.
Built in VOX circuit enabling the VOX op-
eration* (voice operated transmission)
*To use the VOX operation, an optional headset and a plug
adapter cable are additionally required.
PRECAUTIONS
RWARNING RF EXPOSURE! This device emits NEVER connect the transceiver to a power source using
Radio Frequency (RF) energy. Caution should be observed reverse polarity. This will ruin the transceiver.
when operating this device. If you have any questions re-
garding RF exposure and safety standards, please refer to DO NOT operate the transceiver near unshielded electri-
the Federal Communications Commission Office of Engi- cal blasting caps or in an explosive atmosphere.
neering and Technologys report on Evaluating Compliance
with FCC Guidelines for Human Radio Frequency Electro- DO NOT push [PTT] unless you actually intend to trans-
magnetic Fields (OET Bulletin 65) mit.
RWARNING! NEVER hold the transceiver so that BE CAREFUL! The transceiver will become hot when
the antenna is very close to, or touching exposed parts of operating it continuously for long periods.
the body, especially the face or eyes, while transmitting. The
transceiver will perform best if the microphone is 5 to 10 cm DO NOT use or place the transceiver in direct sunlight
(2 to 4 inches) away from the lips and the transceiver is ver- or in areas with temperatures below 20C (4F) or above
tical. +60C (+140F).
RWARNING! NEVER operate the transceiver with Place the unit in a secure place to avoid inadvertent use by
a headset or other audio accessories at high volume levels. children.
Hearing experts advise against continuous high volume op-
eration. If you experience a ringing in your ears, reduce the DO NOT use harsh solvents such as benzene or alco-
volume level or discontinue use. hol to clean the transceiver, because they can damage the
transceivers surfaces.
RWARNING! NEVER operate the transceiver while
driving a vehicle. Safe driving requires your full attention
anything less may result in an accident.
ii
PRECAUTIONS FCC INFORMATION
KEEP the transceiver away from heavy rain, and never FOR CLASS B UNINTENTIONAL RADIATORS:
immerse in the water. The transceiver meets IP54* require- This equipment has been tested and found to comply with
ments for dust-protection and splash resistance. However, the limits for a Class B digital device, pursuant to part 15 of
once the transceiver has been dropped, dust-protection and the FCC Rules. These limits are designed to provide reason-
splash resistance cannot be guaranteed because of possible able protection against harmful interference in a residential
damage to the transceivers case or the waterproof seal. installation. This equipment generates, uses and can radi-
* Only when the battery pack/case, antenna and jack cover are at- ate radio frequency energy and, if not installed and used
tached. in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
NEVER operate or touch the transceiver with wet hands. guarantee that interference will not occur in a particular in-
This may result in an electric shock or may damage the stallation. If this equipment does cause harmful interference
transceiver. to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
Even when the transceiver power is OFF, a slight current still try to correct the interference by one or more of the following
flows in the circuits. Remove the battery pack or batteries measures:
from the transceiver when not using it for a long time. Oth- Reorient or relocate the receiving antenna.
erwise, the installed battery pack or batteries will become Increase the separation between the equipment and re-
exhausted, and will need to be recharged or replaced. ceiver.
Connect the equipment into an outlet on a circuit differ-
Approved Icom optional equipment is designed for optimal ent from that to which the receiver is connected.
performance when used with an Icom transceiver. Consult the dealer or an experienced radio/TV techni-
Icom is not responsible for the destruction or damage to an cian for help.
Icom transceiver in the event the Icom transceiver is used
with equipment that is not manufactured or approved by
CAUTION: Changes or modifications to this device, not
Icom.
expressly approved by Icom Inc., could void your authority
to operate this device under FCC regulations.
iii
SUPPLIED ACCESSORIES 1
2
The following accessories are supplied with the transceiver.
3
Battery pack* Antenna 4
5
6
Jack cover Belt clip*
(with screws)
7
8
9
10
11
Battery charger* AC adapter* 12
13
14
15
16
Icom, Icom Inc. and the Icom logo are registered trademarks of
Icom Incorporated (Japan) in Japan, the United States, the United 17
Kingdom, Germany, France, Spain, Russia and/or other countries.
* Not supplied, or the shape is different, 18
depending on the version. Microsoft, Windows and Windows Vista are registered trademarks of
Microsoft Corporation in the United States and/or other countries.
19
iv
TABLE OF CONTENTS
FOREWORD...................................................................................... i Monitor function......................................................................14
FEATURES......................................................................................... i Mode selection.......................................................................15
EXPLICIT DEFINITIONS.................................................................... i Operating mode selection.......................................................16
IMPORTANT....................................................................................... i Setting a tuning step...............................................................16
PRECAUTIONS.............................................................................iiiii Setting a frequency.................................................................16
FCC INFORMATION........................................................................ iii Receiving................................................................................17
SUPPLIED ACCESSORIES............................................................. iv Transmitting.............................................................................17
TABLE OF CONTENTS................................................................ vvi Key lock function.....................................................................18
[VOL] function assignment......................................................18
1 ACCESSORIES............................................................12 Weather channel operation (U.S.A. version only)...................19
Antenna....................................................................................1
Belt clip.....................................................................................1 5 REPEATER AND DUPLEX OPERATION................2023
Battery pack/case.....................................................................2 Repeater operation.................................................................20
Jack cover.................................................................................2 Duplex operation.....................................................................21
Subaudible tones....................................................................22
2 PANEL DESCRIPTION.................................................37 Lockout function......................................................................23
.. Front, top and side panels........................................................3 Auto repeater function (U.S.A. version only) ..........................23
Function display........................................................................6
6 MEMORY/CALL OPERATION.................................2428
3 BATTERY CHARGING...............................................813 General description................................................................24
Caution (for the BP-264 Ni-MH battery).................................... 8 Selecting a memory channel..................................................24
Caution (for the BP-265 Li-Ion battery).....................................9 Selecting the Call channel......................................................24
Battery chargers.....................................................................11 Channel programming............................................................25
Battery case (BP-263)................................................................ 13 Copying memory/Call contents...............................................26
Battery information.................................................................13 Clearing memory contents..............................................................27
Display type............................................................................27
4 BASIC OPERATION.................................................1419 P rogramming a channel name..................................................28
Power ON...............................................................................14
Adjusting the volume level......................................................14
Adjusting the squelch level.....................................................14
TABLE OF CONTENTS 1
2
7 SCAN OPERATION..................................................2931 13.................
TROUBLE SHOOTING...................................................50
Scan types..............................................................................29 3
.. Programmed scan .................................................................29 14 OPTIONS..................................................................5153
Memory Scan.........................................................................30 VOX function...........................................................................52 4
Setting skip channels..............................................................30
15 SPECIFICATIONS..........................................................54
5
Scan resume setting...............................................................30
Priority watch..........................................................................31 6
16 CE.............................................................................5556
8 TONE SQUELCH AND POCKET BEEP..................3234 7
Tone/DTCS squelch and pocket beep.....................................32
Tone scan...............................................................................34
8
9
9 DTMF MEMORY.......................................................3537
Programming a DTMF code sequence...................................35 10
Transmitting a DTMF code sequence.....................................36
Confirming a DTMF memory..................................................37 11
Setting DTMF transfer speed..................................................37
12
10 SET MODES.............................................................3847 13
Set mode programming..........................................................38
Set mode items.......................................................................39 14
Initial Set mode programming................................................... 43
Initial Set mode items.............................................................44 15
11 CLONING.......................................................................48
16
Cloning operation....................................................................48 17
12 RESETTING...................................................................49 18
Resetting................................................................................49
19
vi
1 ACCESSORIES
Battery pack/case
ACCESSORIES 1
Battery pack/case NEVER remove or attach the battery pack/case when the
transceiver is wet or soiled. This may result in water or
1
To attach the battery pack/case: dust getting into the transceiver/battery pack/case, and 2
may result in them being damaged.
q Fit the battery pack/case in the direction of the arrow (q), 3
then close. NOTE: Keep the battery terminals clean. Its a good idea
w Hook the latch until it makes a click sound (w). 4
to clean the battery terminals once a week.
q 5
Battery pack/case Jack cover 6
7
Attach the jack cover when optional equipment is not used.
w 8
To attach the jack cover To detach the jack cover
Latch q A ttach the jack cover to e Remove the screws with a 9
the [SP MIC] jack. phillips screwdriver.
w Tighten the screws. r D etach the jack cover to
10
To remove the battery pack/case: connect optional equip- 11
ment.
Be careful! The latch is tightly locked, so use caution 12
when releasing it. DO NOT use your finger nail. Use the
edge of a coin or screwdriver tip to carefully release it. 13
U
nhook the latch (e), and lift up the battery pack/case in e 14
the direction of the arrow (r). w
q 15
e r
r 16
w
17
18
19
e
2 PANEL DESCRIPTION
PANEL DESCRIPTION 2
[8] [SET](8)
Numeric input and DTMF code: 8
After pushing [FUNC](M), enters the Set mode.
(p.38)
PANEL DESCRIPTION 2
Function display 1
e TONE INDICATOR 2
qw e r t y
appears while the repeater tone encoder is ON. 3
(p.20)
u appears while the tone squelch function is ON. 4
!5 (p.33)
!4
i 5
o D appears while the DTCS squelch function is ON.
!3 (p.33) 6
appears with the or D indicator while the pocket
!2 !1 !0 beep function (with CTCSS or DTCS) is ON. (p.33)
7
r MEMORY INDICATOR
8
Appears when the memory mode is selected. (pp.15, 24) 9
q BUSY INDICATOR t FREQUENCY READOUT 10
A ppears when a signal is being received, or the D isplays the operating frequency, memory channel,
Set modes contents and a variety of other information. 11
squelch is open.
Blinks while the monitor function is ON. (p.14) The decimal point blinks during scan. 12
D uring memory mode operation, the programmed
w SIGNAL INDICATOR memory name is displayed. 13
Shows the strength of the received signal. (p.17)
y BATTERY INDICATOR (p.13) 14
(battery indicators) appear when the battery 15
pack/case is attached.
Weak RX Signal level Strong
appears when the battery pack must be changed, 16
W hile transmitting, shows the output power level. or batteries must be replaced. 17
(p.17)
18
19
Low Middle High
2 PANEL DESCRIPTION
BATTERY CHARGING 3
Caution (for the BP-264 Ni-MH battery) Clean the battery terminals to avoid rust or misscontact. 1
R
DANGER! NEVER short terminals (or charging terminals)
eep battery terminals clean. Its a good idea to clean bat-
K 2
tery terminals once a week.
of the battery pack. Also, current may flow into nearby metal 3
objects such as a necklace, so be careful when placing bat- If your Ni-MH battery pack seems to have no capacity, even
tery packs (or the transceiver) in handbags, etc. after being charged, completely discharge it by leaving the 4
power ON overnight. Then, fully charge the battery pack again.
Simply carrying with or placing near metal objects such as
If the battery pack still does not retain a charge (or only very lit-
5
a necklace, etc. may cause shorting. This may damage not
only the battery pack, but also the transceiver. tle charge), a new battery pack must be purchased. (p. 51) 6
Prior to using the transceiver for the first time, the battery
R
DANGER! NEVER incinerate used battery packs. Internal
pack must be fully charged for optimum life and operation.
7
battery gas may cause an explosion.
Recommended temperature range for charging: 8
R
DANGER! NEVER immerse the battery pack in water.
between +10C and +40C (rapid charge: with BC-191) or 9
If the battery pack becomes wet, be sure to wipe it dry BE-
between 0C and +45C (regular charge: with BC-192)
FORE attaching it to the transceiver.
Use the supplied charger or optional charger (BC-191 for 10
CAUTION: Always use the battery within the specified tem-
perature range, 5C to +60C (+23F to +140F). Using the
rapid charging, BC-192 for regular charging) only. NEVER 11
use other manufacturers chargers.
battery out of its specified temperature range will reduce the 12
batterys performance and battery life. The battery pack contains a rechargeable battery.
AUTION: Shorter battery life could occur if the battery is
C Charge the battery pack before first operating the trans-
13
left completely discharged, or in an excessive temperature ceiver, or when the battery pack becomes exhausted. 14
environment (above +55C; +131F) for an extended period If you want to prolong the battery life, the following points
of time. If the battery must be left unused for a long time, should be observed: 15
it must be detached from the radio after charging. Keep it Avoid over charging. The charging time period should be 16
safely in a cool dry place at the following temperature range: less than 48 hours.
20C to +45C (4F to +113F) (up to a month)
17
Use the battery pack until it becomes almost completely
20C to +35C (4F to +95F) (up to six months) exhausted, under normal conditions. We recommend bat- 18
20C to +25C (4F to +77F) (up to a year*) tery charging after transmitting becomes impossible. 19
* We recommend charging the battery pack every 6 months.
3 BATTERY CHARGING
R
WARNING! NEVER put the battery in a microwave oven, R
WARNING! DO NOT charge or leave the battery in the 1
high-pressure container, or in an induction heating cooker. battery charger beyond the specified time for charging. If the
This could cause a fire, overheating, or cause the battery to battery is not completely charged by the specified time, stop 2
rupture. charging and remove the battery from the battery charger. 3
Continuing to charge the battery beyond the specified time
AUTION: Always use the battery within the specified tem-
C
limit may cause a fire, overheating, or the battery may rup- 4
perature range, 20C to +60C (4F to +140F). Using the
ture.
battery out of its specified temperature range will reduce the 5
batterys performance and battery life. R
WARNING! NEVER insert the transceiver (battery at-
tached to the transceiver) into the charger if it is wet or
6
AUTION: Shorter battery life could occur if the battery is
C
left fully charged, completely discharged, or in an excessive soiled. This could corrode the battery charger terminals or 7
temperature environment (above +50C; +122F) for an ex- damage the charger. The charger is not waterproof.
8
tended period of time. If the battery must be left unused for a AUTION: DO NOT charge the battery outside of the spec-
C
long time, it must be detached from the radio after discharg- ified temperature range: BC-193 (+10C to +40C; +50F 9
ing. You may use the battery until the battery indicator shows to +104F). Icom recommends charging the battery at +20C
10
half-capacity, and then keep it safely in a cool dry place at (+68F). The battery may heat up or rupture if charged out of
the following temperature range: the specified temperature range. Additionally, battery perfor- 11
20C to +50C (4F to +122F) (up to a month) mance or battery life may be reduced.
12
20C to +35C (4F to +95F) (up to three months)
20C to +20C (4F to +68F) (up to a year) 13
14
D Charging caution The supplied battery pack, charger, and AC adapter dif-
R
DANGER! NEVER charge the battery pack in areas with fer, or no supplied depending on the version. 15
Prior to using the transceiver for the first time, the battery
extremely high temperatures, such as near fires or stoves, 16
inside a sun-heated vehicle, or in direct sunlight. In such en- pack must be fully charged for optimum life and operation.
vironments, the safety/protection circuit in the battery will ac- 17
tivate, causing the battery to stop charging. 18
19
10
3 BATTERY CHARGING
Battery chargers DU
sing the BC-192 to regular charge the BP-264
The BC-192 provides regular charging of only the BP-264
D Using the BC-191 to rapid charge the BP-264 Ni-MH battery pack. Never use it to charge any other battery
The BC-191 provides rapid charging of only the BP-264 Ni-MH pack.
battery pack. Never use it to charge any other battery pack. Charging time (with the 147S): Approx. 16 hours
Charging time: Approx. 2 hours The following item is additionally required:
An AC adapter (not supplied with some versions) or the OPC-515L
The following item is additionally required:
DC power cable.
An AC adapter (not supplied with some versions) or the OPC-515L
or CP-23L DC power cable. Battery pack Transceiver
AC adapter
AC adapter Battery pack Transceiver
(A different type, or no AC
(A different type, or no AC adapter is supplied, de-
adapter is supplied, de- pending on the version.)
pending on the version.)
D Using the BC-193 to rapid charge the BP-265 IMPORTANT: Battery charging caution 1
The BC-193 provides rapid charging of only the BP-265 Li- Ensure the tabs on the battery pack are correctly aligned
Ion battery pack. Never use it to charge any other battery with the guide rails inside the charger. 2
pack. Tabs 3
Charging time: Approx. 2.5 hours
4
The following item is additionally required:
An AC adapter (not supplied with some versions) or the OPC-515L 5
or CP-23L DC power cable. 6
AC adapter Battery pack Transceiver
(A different type, or no AC 7
adapter is supplied, de-
pending on the version.) 8
Guide rail
9
CAUTION: When using the OPC-515L DC power cable 10
NEVER connect the OPC-515L to a power source using 11
reverse polarity. This will ruin the battery charger.
Turn power OFF White line: + Black line: 12
Screws*
13
(Self tapping screw:
M3.5 at least 30 mm)
14
*Purchase separately. 15
Using screws is
recommended to
secure the charger.
16
The optional OPC-
515L (for DC power 17
source) or CP-23L Charge indicator
(for 12 V cigarette Lights orange : While charging 18
lighter socket) can Lights green : Charging is completed.
be used instead of 19
the AC adapter.
12
3 BATTERY CHARGING
Mode selection
P ush [VFO/MR/CALL] several D Memory mode
times to select the VFO mode, The memory mode is used for Memory mode display
memory mode, Call channel mode operating on memory channels,
and weather channel mode*, in se- which store programmed fre-
quence. quencies.
*For only the U.S.A. version transceivers. appears when the memory Appears
mode is selected.
15
BASIC OPERATION 4
Receiving Transmitting
Make sure the BP-264 or BP-265 battery pack is fully AUTION: Transmitting without an antenna will damage
C
charged, or the BP-263 battery case has brand new alkaline the transceiver.
batteries (pp.1113). OTE: To prevent interference, push and hold [MONI] to
N
listen on the frequency before transmitting.
q Push and hold [ ] for 1 sec. to turn power ON.
w Rotate [VOL] to set the desired volume level. (p. 14) q Set the operating frequency. (p. 16)
The volume level is displayed on the LCD while adjusting.
w Push [FUNC](M), and then push [H/M/L](9) to select the
e Set the receive frequency. (p. 16) output power between High (5.5 W), Mid (2.5 W) and Low
r Set the squelch level. (p. 14) (0.5 W).
While pushing and holding [MONI], push [] or [].
H, M, or L appears according to the selected output power.
The squelch level is displayed on the LCD while setting.
e Push and hold [PTT] to transmit.
SqL 1 is loose squelch (for weak signals) and SqL10 is tight
appears while transmitting.
squelch (for strong signals). SqL 0 is open squelch.
The signal indicator shows the output power level.
Push and hold [MONI] to open the squelch manually.
r Speak into the microphone using your normal voice level.
t When a signal is received: DO NOT hold the transceiver too close to your mouth or speak
The squelch is opened and the audio is heard.
too loudly. This may distort your speech.
The signal indicator shows the relative signal strength level.
t Release [PTT] to return to receive.
R WARNING! When using the BP-263 battery case, fre- [VOL] function assignment 1
quent or continuous transmissions can cause the batter-
ies to overheat, and may cause a burn. To prevent this, the [VOL] can be used as a tuning control instead of [] and
2
default time-out timer is set to 5 minutes (p. 44). Be careful [], to suit your preference. However, when [VOL] functions 3
when the time-out timer function is turned OFF or set to a as a tuning control, [] and [] function as volume controls.
long time period, and transmission is made for long periods.
4
q While pushing and holding [] and [], turn the power
We recommend using the middle or low power setting. 5
ON to enter the Initial Set mode.
w Push [] or [] to select the dial assignment item. (tOP) 6
e Rotate [VOL] to select an option.
Key lock function r Push [# ENT] to exit the Initial Set mode.
7
8
To prevent accidental frequency changes, or unnecessary
function access, use the key lock function.
[VOL] 9
Push [FUNC](M), and then push and hold [ ](# ENT) for
10
1sec. to turn the key lock function ON or OFF.
[VOL] functions as the volume control.
appears while the key lock function is activated. 11
[ ], [VOL], [MONI], [PTT] and [FUNC](M) + [ ](# ENT)
are still operable while the key lock function is ON.
12
13
14
[VOL] functions as the tuning control.
15
[ VOL] and []/[] function as described below, depend- 16
ing on the option.
17
Option [VOL] []/[]
Appears
18
tOP.VO Volume control Tuning controls
tOP.di Tuning control Volume controls
19
18
4 BASIC OPERATION
19
REPEATER AND DUPLEX OPERATION 5
Repeater operation 1
When using a repeater, the transmit frequency is shifted r Push and hold [PTT] to transmit. 2
from the receive frequency by the frequency offset (p. 21). The displayed frequency automatically changes to the transmit 3
This is called duplex operation. It is convenient to program frequency (repeater input frequency).
repeater information into memory channels (p. 25). If OFF appears, check the frequency offset and shift direction 4
Repeater
(p. 21). 5
t Release [PTT] to receive.
144.700 MHz 144.700 MHz Uplink
(transmit freq.)
While receiving While transmitting
6
Downlink
145.300 MHz 145.300 MHz
(receive freq.) 7
8
Station A Station B
9
y Push and hold [MONI] to check whether the other stations
transmit signal can be directly received or not. 10
When the other stations signal can be directly received, move
q Set the receive frequency (the repeater output frequency). to a non-repeater frequency to use simplex. (duplex OFF)
11
w Push [FUNC](M), and then [DUP](4) several times to set 12
the shift direction of the transmit frequency. ( or +; For the U.S.A. version:
See page 21 for details.) Auto repeater function uses standard values of the re- 13
When the auto repeater function is in use (U.S.A. version only), peater tone frequency and frequency offset. 14
this selection and step e are not necessary. (p. 23).
e If desired, push [FUNC](M) and then [TONE](1) several 15
times to activate the subaudible tone encoder. 16
appears. Appears
S elect the desired subaudible 17
tone frequency. (p. 22) 18
19
20
5 REPEATER OPERATION
Duplex operation
D Setting the frequency offset For the U.S.A. version:
q Push [FUNC](M), and then [SET](8) to enter the Set mode. The auto repeater function has priority over the manual
w Push [] or [] to select the offset item. duplex setting. If the transmit frequency changes after
blinks, and the current frequency offset appears. setting, the auto repeater function may have changed the
e Rotate [VOL] to select the frequency offset. duplex setting. Turn the auto repeater function OFF to
T he offset is selected in the 0.6 MHz offset
prevent this (p. 23).
same step as the frequency
tuning step. D Reverse duplex function
T he unit of the frequency When the reverse duplex function is ON, the receive and
offset is MHz. transmit frequencies are reversed. The function can be set in
r Push [# ENT] to exit the Set mode. the Set mode.
D Setting the duplex direction q Push [FUNC](M), and then [SET](8) to enter the Set mode.
w Push [] or [] to select the reverse duplex function item
ush [FUNC](M), and then [DUP](4) to select (nega-
P (REV).
tive offset) or + (positive offset). e Rotate [VOL] to turn the function ON or OFF.
or + indicates the transmit frequency is shifter up (+) or r Push [# ENT] to exit the Set mode.
down () from the receive frequency.
Blinking or + indicates the reverse duplex function is ON, Each receive and transmit frequency is shown in the table
as described to the right. below, with the following configurations;
Example When the offset frequency is 0.6 MHz Input freq. : 145.300 MHz Reversed RX freq. TX freq.
Direction : (down)
Duplex While receiving While transmitting Offset : 0.6 MHz OFF 145.300 MHz 144.700 MHz
ON 144.700 MHz 145.300 MHz
+ (up)
21
REPEATER OPERATION 5
23
MEMORY/CALL OPERATION 6
General description D Using the keypad 1
q Push [VFO/MR/CALL] several times to select the memory
The transceiver has 207 memory channels, including 6 scan mode.
2
edge memory channels (3 pairs), and 1 Call channel, for X appears. 3
storage of often-used frequencies. w To select a desired channel, enter the 3 digits of the chan-
nel number using the keypad.
4
D Memory channel contents Blank channels are also selectable. 5
The following information can be programmed into a mem- Entering one or two digits, and then pushing [# ENT] also se-
ory channel: lects a memory channel. 6
Operating frequency (p.16) Example selecting memory channel 14 7
Operating mode (p.16) Push
Duplex direction (+ or ) with frequency offset (p.21) 8
Reverse duplex function ON/OFF (p.40)
S ubaudible tone encoder (p.20), tone squelch or DTCS 9
squelch ON/OFF (p.33) 10
Subaudible tone frequency (p. 22), tone squelch frequency or
Appears The memory channel
DTCS code with polarity (pp.32, 33) is selected. 11
Skip setting (p.30)
Tuning step (p.16) 12
Output power (p.17)
TX permission (p.41)
Selecting the Call channel 13
Push [VFO/MR/CALL] several times to select the Call 14
Selecting a memory channel channel.
C appears instead of the memory channel number.
15
D Using [] or [] 16
q Push [VFO/MR/CALL] several times to select the memory Push 17
mode. 18
X appears. Appears
w Push [] or [] to select a desired channel. 19
O
nly programmed channels are displayed.
24
6 MEMORY/CALL OPERATION
Channel programming
q Push [VFO/MR/CALL] several times to select the VFO t P ush [FUNC](M), and then push and hold [VFO/MR/
mode. CALL] for 1sec. to store the entry.
w Set a desired frequency. (p. 16) 3 beeps sound.
If desired, set other data (e.g. offset frequency, duplex If you continue to push and hold [VFO/MR/CALL] for 1 sec.
direction, tone squelch, etc.). after programming, the memory channel number automatically
e Push [FUNC](M), and then [VFO/MR/CALL]. increases.
X and the memory channel number blink.
NOTE: To cancel programming, push [VFO/MR/CALL]
Select the Call channel mode to program the Call channel.
r Push [] or [] to select a desired channel. before storing the entry in step t.
Select 1A/1B to 3A/3B to program a scan edge channel.
25
MEMORY/CALL OPERATION 6
27
MEMORY/CALL OPERATION 6
P
rogramming a channel name 1
Each memory channel can be programmed with an alphanu- i Rotate [VOL] to select a desired character.
2
meric name for easy recognition and can be displayed inde- The selected character blinks. 3
pendently by channel. Up to 5 characters can be used for a Push [] to move the cursor right, push [] to move the cur-
channel name. sor left.
4
5
q While pushing and holding [] and
[], turn the power ON to enter the [VOL] 6
Initial Set mode.
w Push []/[] to select the channel
o R epeat step i until the desired channel name is pro- 7
grammed.
name display item. (dSP)
!0 Push [# ENT] to exit the programming mode. 8
e Rotate [VOL] to select the channel
name display type, dSP.nm. 9
r Push [# ENT] to exit the Initial Set 10
mode.
t Push [VFO/MR/CALL] several times 11
to select the memory mode. D Usable characters 12
Select the Call channel to program a
Call channel name. 13
(A) (b) (C) (d) (E) (F) (G) (H) (I) (J) (k) (L) (m)
y Push [] or [] to select a desired channel. 14
u Push [FUNC](M), and then [SET](8) to enter the channel
name programming mode. (n) (O) (P) (q) (R) (S) (t) (U) (V) (W) (X) (y) (Z) 15
A cursor blinks for the first character.
(1) (2) (3) (4) (5) (6) (7) (8) (9) (0) 16
17
(+) (-) (=) () (/) (() ()) (:) (Space)
18
19
28
7 SCAN OPERATION
Priority watch
A priority watch checks for signals on priority channels D Memory scan watch
while operating on a VFO frequency. While operating on a VFO frequency, a memory scan watch
checks for signals on each memory channel in sequence,
D Memory or Call channel watch every 5 sec.
While operating on a VFO frequency, the memory or Call
channel watch checks for signals on the selected channel q Push [VFO/MR/CALL] several times to select the memory
every 5 sec. mode.
w Push [FUNC](M), and then [SCAN](5) to start a memory
q Select a desired memory channel or the Call channel. scan.
w Push [FUNC](M), and then [PRIO](7) to start the watch. e Push [FUNC](M), and then [PRIO](7) to start the watch.
The decimal point ., on the frequency readout blinks. The VFO mode is selected, and the decimal point ., on the fre-
When a signal is detected on the channel, the watch resumes quency readout blinks.
according to the scan resume setting. (p. 30) When a signal is detected on a channel, the watch resumes ac-
VFO frequency Memory channel cording to the scan resume setting. (p. 30)
Memory scan
VFO frequency
Mch 0
5 sec. Mch 1 SKIP
Mch 2
e To cancel the watch, push any key except [ ], []/[], Mch 199
[MONI], [FUNC](M), or [PTT]. 5 sec.
31
TONE SQUELCH AND POCKET BEEP 8
Tone/DTCS squelch and pocket beep 1
D Tone squelch and DTCS squelch D Setting CTCSS tone or DTCS code 2
The tone squelch (CTCSS) or DTCS squelch opens only q Push [FUNC](M), and then [SET](8) to enter the Set mode. 3
when receiving a signal that includes a matched CTCSS tone w Push [] or [] to select the CTCSS tone item (Ct) or 4
or DTCS code, respectively. You can silently wait for calls the DTCS code item (dt).
using the same tone or code. Separate tone frequencies can blinks when selecting the CTCSS tone item, and D blinks 5
be set for repeater and tone squelch/pocket beep operation. when selecting the DTCS code item.
6
e Rotate [VOL] to select a desired CTCSS tone or DTCS
D Pocket beep code. 7
The pocket beep function uses subaudible tones or DTCS The recommended CTCSS tone or DTCS code are shown to
codes for calling, and can be used as a common pager to the left.
8
inform you that someone has called while you were away r Push [# ENT] to exit the Set mode. 9
from the transceiver.
10
Recommended CTCSS tones (unit: Hz) [VOL] CTCSS tone setting
11
67.0 79.7 94.8 110.9 131.8 156.7 186.2 225.7
69.3 82.5 97.4 114.8 136.5 162.2 192.8 233.6 12
71.9 85.4 100.0 118.8 141.3 167.9 203.5 241.8 13
74.4 88.5 103.5 123.0 146.2 173.8 210.7 250.3
77.0 91.5 107.2 127.3 151.4 179.9 218.1
DTCS code setting
14
Recommended DTCS code
15
023 051 114 143 174 251 315 371 445 532 631 723 16
025 054 115 152 205 261 331 411 464 546 632 731
17
026 065 116 155 223 263 343 412 465 565 654 732
031 071 125 156 226 265 346 413 466 606 662 734 18
032 072 131 162 243 271 351 423 503 612 664 743
043 073 132 165 244 306 364 431 506 624 703 754 19
047 074 134 172 245 311 365 432 516 627 712
32
8 TONE SQUELCH AND POCKET BEEP
q Push [FUNC](M), and then [SET](8) to enter the Set mode. Push , and then to select the tone function in sequence.
w Push [] or [] to select the DTCS polarity item (dtP).
e Rotate [VOL] to select a desired polarity setting between
dtP.nn (normal), dtP.nR (TX: normal, RX: reverse), dtP.Rn
(TX: reverse, RX: normal) and dtP.RR (reverse). Repeater tone Function OFF
33
TONE SQUELCH AND POCKET BEEP 8
37
SET MODES 10
Set mode programming 1
The Set mode is used to change the settings of the trans- D Set mode operation 2
ceivers functions. q Push [FUNC](M), and then [SET](8) to enter the Set mode. 3
w Push [] or [] to select the desired item.
e Rotate [VOL] to select the option or value.
4
r To exit the Set mode, push [# ENT]. 5
Repeater tone
frequency (p. 39)
Tone squelch
frequency (p. 39) DTCS code (p. 39) DTCS polarity (p. 39) Frequency offset (p. 40)
6
7
8
Operating mode (p. 42) Reverse duplex functon (p. 40)
9
: Push 10
DTMF TX key (p. 42) : Push Tuning step (p. 40) 11
12
*Appears for only the U.S.A.
version transceivers. 13
VOX time-out timer (p. 42) Scan resume setting (p. 40)
14
NOTE: When the display type setting (pp. 27, 46) is set
to CH in the Initial Set mode, and accessing the Set 15
mode from the memory mode, most of Set mode items
VOX delay (p. 41) do not appear. Function key timer (p. 40) 16
17
18
Microphone gain (p. 41) VOX gain (p. 41) Weather alert* (p. 41) TX permission (p. 41) LCD backlight (p. 41)
19
38
10 SET MODES
41
SET MODES 10
Key-touch beep (p. 44) Time-out timer (p. 44) Auto repeater* (p. 44) Auto power-OFF (p. 44) Lockout (p. 45)
Microphone simple
mode (p. 47) Select speed (p. 46) Power save (p. 46) LCD contrast (p. 46) Display type (p. 46)
43
SET MODES 10
D Dial assignment
D Squelch delay Selects whether or not to use [VOL] as a tuning control in-
Sets the squelch delay between short and long. The delay stead of [] and []. When [VOL] functions as a tuning con-
prevents the squelch from repeatedly opening and closing trol, [] and [] function as volume controls.
while receiving the same signal. tOP.VO : Audio volume control (default)
Sqd. S : Sets the squelch delay to short (default). tOP.dI : Tuning dial
Sqd. L : Sets the squelch delay to long.
45
SET MODES 10
U
ser remote control unit D Auto low power
The below circuit is for reference only.
Turns the auto low power function ON or OFF.
to the [SP] jack
When the temperature goes below 0C (+32F), the function
REMOTE 3.5(d) mm automatically sets the output power to low.
2.7kW 6.8kW 15kW 33kW
In that case, the transmit power selections (Hi/Mid) are also
S1 S2 S3 S4 SP disabled. (default: ALP.OF)
+
GND
EXTERNAL SPEAKER
Rated input >
700 mW (8 W)
47
CLONING 11
Cloning operation 1
Cloning allows you to quickly and easily transfer the e Turn the sub transceiver ON.
2
programmed contents from one transceiver to another. r Push [PTT] on the master transceiver. 3
CL Out appears on the master transceivers display, and the
D Transceiver-to-transceiver cloning signal indicator shows the data is being transferred to the sub 4
transceiver.
q Turn the transceivers power OFF, and then connect an
CL In appears on the sub transceivers display, and the signal
5
optional OPC-474 cloning cable to the [SP] jacks of the
master transceiver and the sub transceiver.
indicator shows the data is being received from the master 6
transceiver.
The master transceiver is used to send data to the sub trans- t When cloning is finished, turn both the transceivers OFF. 7
ceiver. Then turn them ON again to exit the cloning mode. 8
NOTE: DO NOT push [PTT] on the sub transceiver dur-
ing cloning. This will cause a cloning error. 9
10
D Cloning using a PC
The CS-V80 cloning software is also used to clone/edit con- 11
tents with a PC (for Microsoft Windows 2000/XP or Win- 12
dows Vista) using ICF format files.
Master transceiver Refer to the INSTRUCTIONS and the Help file that come 13
with the CS-V80, for details. 14
OPC-478UC
to USB port
15
Sub transceiver (USB type)
Resetting
The LCD may occasionally display erroneous infor- D All reset
mation (e.g. when first applying power). This may be The all reset clears all programming and returns all
caused externally by static electricity or by other factors. settings to their factory defaults.
If this problem occurs, turn power OFF. After waiting a q Push and hold [ ] for 1 sec. to turn the power OFF.
few seconds, turn power ON again. If the problem per- w While pushing and holding [MONI] and [VFO/MR/CALL],
sists, perform either or both of the procedures below. push and hold [ ] for 1 sec. to turn the power ON.
CLEAR appears when resetting the CPU.
D Partial reset
If you want to reset the operating conditions (VFO fre-
quency, VFO settings, and Set modes contents) with-
out clearing the memory contents, use the partial reset.
q Push and hold [ ] for 1 sec. to turn the power OFF.
w While pushing and holding [VFO/MR/CALL], push and
hold [ ] for 1 sec. to turn the power ON.
VOX function 1
2
The transceiver has a VOX function, which allows hands-free D Turning the VOX function ON or OFF
operation. q Connect an optional headset and plug adapter cable to 3
An optional HS-94, HS-95 or HS-97 headset and the
OPC-2004 plug adapter cable are also required for operation.
the transceiver, and then turn the power ON. 4
w Push [FUNC](M), and then [VOX](2) to turn the VOX func-
The VOX (voice operated transmission) function starts transmis- tion ON or OFF. 5
sion when you speak into the microphone, without needing to
push [PTT]; then, automatically returns to reception when you stop
VOX appears when the VOX function is ON. 6
speaking. NOTE: 7
W hen using the VOX function, adjust the microphone gain
D Optional unit connection and the VOX-related settings (p. 53) to suit your operating 8
q Push and hold [ ] for 1 sec. to turn the power OFF. environment (including your headset performance). 9
w Remove the jack cover. (p. 2) Set the microphone gain before setting the VOX gain in
e C onnect the optional HS-94, HS-95 or HS-97 and the Set mode (p. 41). We recommend setting the micro- 10
OPC-2004, as illustrated below. phone gain to 3. 11
When the TX permission is set to OFF in the Set mode,
OPC-2004 HS-94 you cannot transmit using the VOX function. (p. 41) 12
13
14
w
15
e
16
q 17
Appears
18
[ ]
19
52
14 OPTIONS
D VOX-related settings
The VOX gain, the VOX delay, and the VOX time-out timer can If On is intermittent, be sure the VOX delay is set long
be set in the Set mode. enough to allow normal pauses in speech, but keep the
VOX ON until you finish speaking.
q Connect an optional headset and plug adapter cable to
the transceiver, and then turn the power ON. CONVENIENT!
w Push [FUNC](M), and then [VOX](2) to turn the VOX func- While transmitting using the VOX function, you can adjust
tion ON.
the VOX gain simply by rotating [DIAL].
e Push [FUNC](M), and then [SET](8) to enter the Set mode.
r Push [] or [] to select the VOX gain (VOX), the VOX
VOX delay
delay (VXd), or the VOX time-out timer (Vto) item.
t Rotate [VOL] to select a desired option. Sets the VOX delay to between 0.5 and 3.0 sec. (in 0.5 sec.
y Push [# ENT] to exit the Set mode. steps). The VOX delay is the amount of time the transmitter
stays ON after you stop speaking. (default: VXd.10)
The VOX function does not activate transmission while in
the Set mode.
VOX gain
The VOX delay is set to The VOX delay is set to
The VOX gain level can be adjusted between 1 (minimum) and 1 sec. 3 sec.
10 (maximum), or turned OFF. Higher values make the VOX
function more sensitive to your voice. (default: VOX.05) VOX time-out timer
Sets the VOX time-out timer to between 1, 2, 3, 4, 5, 10 and
15 min. to prevent accidental prolonged transmission for the
VOX function.
The VOX function is The VOX gain is set to To turn the function OFF, select Vto.OF. (default: Vto.03)
turned OFF. 10 (maximum).
While speaking into the head-
set microphone, adjust the
VOX gain until On continu-
ously appears on the LCD. The VOX time-out timer must be set shorter than the time-
Appears
out timer, otherwise this timer will not be activated.
53
SPECIFICATIONS 15
D General 1
Frequency coverage : (unit: MHz) Dimensions : 58(W)112(H)30(D) mm;
Version TX RX (projections not included) 2932(W)41332(H)1316(D) in 2
U.S.A.
144148 136174*
Weight (approx.) 3
AUS (without battery pack/case and ant.) : 140 g; 4.9 oz
CHN 4
136174* 136174* D Transmitter
EXP
Modulation system : Variable reactance freq. modulation
5
EUR
UK 144146 144146
Output power (at 7.2 V DC) : High 5.5 W, Mid. 2.5 W, Low 0.5 W. 6
Max. frequency deviation : FM (wide) 5.0 kHz
KOR
FM (narrow) 2.5 kHz 7
* Guaranteed: Only 144148 MHz range Spurious emissions : Less than 60 dBc 8
Mode : FM, FM-N External mic. connector : 3-conductor 2.5 (d) mm (110)/2.2 k
Number of memory channels : 207 9
D Receiver
(incl. 6 scan edges and 1 Call channel)
10
Usable temperature range : 20C to +60C; 4F to +140F Receive system : Double-conversion superheterodyne
Tuning steps : 5, 10, 12.5, 15, 20, 25, 30 and Intermediate frequencies : 1st: 21.7 MHz, 2nd: 450 kHz 11
50kHz Sensitivity (at 12 dB SINAD) : 0.14 V typ.
Frequency stability : 2.5 ppm Squelch sensitivity (threshold) : 0.1 V typ.
12
(20C to +60C; 4F to +140F) Selectivity : FM (wide) 70 dB typ. 13
Power supply : Icom specified battery pack/case FM (narrow) 50 dB typ.
Current drain (at 7.2 V DC: typical) Spurious and image rejection : 75 dB typ. 14
Transmit at 5.5 W (High) : 1.4 A Intermodulation : FM (wide) 70 dB typ. 15
at 2.5 W (Mid.) 0.9 A FM (narrow) 65 dB typ.
at 0.5 W (Low) 0.6 A Audio output power (at 10% distortion) 16
Receive standby : 65 mA Internal speaker : 0.75 W typ. with a 16 load
power save 20 mA External speaker : 0.45 W typ. with a 8 load
17
max. audio 310 mA (internal speaker) External speaker connector : 3-conductor 3.5(d) mm; (18)/8 18
180mA (external speaker)
Antenna connector : BNC (50 W) All stated specifications are subject to change without notice or 19
obligation.
54
16 CE
IMPORTANT
When transmitting with a portable radio, hold the radio in List of Country codes (ISO 3166-1)
a vertical position with its microphone 2.5 to 5 centimetres
from your head and body. Country Codes Country Codes
1 Austria AT 18 Liechtenstein LI
If you wear a portable two-way radio on your body, ensure 2 Belgium BE 19 Lithuania LT
that the antenna is at least 2.5 centimetres from your body 3 Bulgaria BG 20 Luxembourg LU
when transmitting. 4 Croatia HR 21 Malta MT
5 Czech Republic CZ 22 Netherlands NL
C
E Versions of the IC-V80E which display 6 Cyprus CY 23 Norway NO
the CE symbol on the serial number label, 7 Denmark DK 24 Poland PL
comply with the essential requirements of the 8 Estonia EE 25 Portugal PT
European Radio and Telecommunication Ter- 9 Finland FI 26 Romania RO
minal Directive 1999/5/EC. 10 France FR 27 Slovakia SK
11 Germany DE 28 Slovenia SI
This warning symbol indicates that this equip- 12 Greece GR 29 Spain EP
ment operates in non-harmonised frequency 13 Hungary HU 30 Sweden SE
bands and/or may be subject to licensing con- 14 Iceland IS 31 Switzerland CH
ditions in the country of use. Be sure to check 15 Ireland IE 32 Turkey TR
that you have the correct version of this radio 16 Italy IT 33 United Kingdom GB
or the correct programming of this radio, to 17 Latvia LV
comply with national licensing requirements.
55
CE 16
1
2
DECLARATION
3
OF CONFORMITY
4
We Icom Inc. Japan 5
1-1-32, Kamiminami, Hirano-ku
Osaka 547-0003, Japan 6
Declare on our sole responsibility that this equipment complies with the
Dsseldorf 16th Oct. 2009
7
Place and date of issue
essential requirements of the Radio and Telecommunications Terminal
Equipment Directive, 1999/5/EC, and that any applicable Essential Test 8
Icom (Europe) GmbH
Suite measurements have been performed.
Himmelgeister strae 100 9
Kind of equipment: VHF TRANSCEIVER D-40225 Dsseldorf
10
Authorized representative name
Type-designation: iV80E 11
Version (where applicable):
Y. Furukawa
General Manager
12
This compliance is based on confor mity with the following har monised 13
standards, specifications or documents:
14
i) EN 301 489-1 v1.8.1 (Apr. 2008)
ii) EN 301 489-15 v1.2.1 (Aug. 2002) 15
iii) EN 301 783-2 v1.1.1 (Sep. 2000) Signature 16
iv) EN 60950-1 (2001): A11: 2004
17
18
19
56
#02 Europe <Intended Country of Use>
#12 Europe-21 AT BE CY CZ DK EE
#22 Europe-22 FI FR DE GR HU IE
#32 Europe-23 IT LV LT LU MT NL
PL PT SK SI ES SE
GB IS LI NO CH BG
RO TR HR
A-6795H-1EX-w
Printed in Japan
20092010 Icom Inc. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
Printed on recycled paper with soy ink.