Professional Documents
Culture Documents
2005 - 04 - Apr - Punching Shear Resis of Flat Slabs Using HSC PDF
2005 - 04 - Apr - Punching Shear Resis of Flat Slabs Using HSC PDF
N. Subramanian
The use of high-strength concrete, with strength exceeding experimental data. Methods adopted to enhance the punching
40 MPa, in reinforced concrete slabs, is becoming popular in shear strength of flat slabs are also discussed.
India and other countries. Current design provisions of major
The concrete flat slab system is a slab and column structure
codes throughout the world are based on empirical
without drop panels and column capitals at the slab and
relationships developed from tests on low-strength concrete. column connection. The flat plate structure is advantageous
In this paper, the existing recommendations in design codes over other slab systems because of the significant savings in
for punching shear failure of slabs are reviewed. Though the construction cost (due to the elimination of beams and
Indian code formulae predict the punching shear resistance of adoption of simple form work) and the resulting aesthetic
high strength concrete slabs as compared to the experimental appearance, especially from the slabs soffit. Moreover, the
results, they do not consider the reinforcement ratio and size elimination of beams reduces the overall height of individual
effects. Hence, a formula similar to that of CEB-FIP code formula floors in a multi-storey building creating additional floor
is suggested. Out of the several methods to enhance the space for a given building height. Due to the above
advantages, such flat slab systems are widely used for multi-
punching shear capacity, the stud shear reinforcement is found
storey structures such as office buildings, car parks, etc, in
to increase the load carrying capacity, punching shear strength several countries.
and ductility of flat slabs. Recent provisions in the American
code allow 100 percent enhancement of shear capacity if shear Flat plate slabs exhibit higher stress at the column
stud reinforcements are used. connection and are most likely to fail due to punching shear
rather than flexural failure, especially when a high
Keywords: BIS provisions, steel shear reinforcement, punching reinforcement ratio is used.
shear, flat slabs, high-strength concrete, stud reinforcement
The catastrophic nature of the punching shear problem
A number of structures including bridges are being built with around the column-slab junction poses a critical problem to
high-strength concrete (HSC)/high performance concretes the engineers concerned. It has to be noted that the punching
(HPC) with strengths exceeding 60 MPa, due to the number
of advantages offered by them. HSC members exhibit, in
some instances, different failure mechanisms and simply
extrapolating models and equations meant for normal
strength to HSC may lead to unsafe designs1.
fc' 1/3
F sd = 0.12 (100fck) u1d ...7(a)
(iii) vn = ...2(c)
3 where,
where, The size effect coefficient,
s = 40 for interior columns, 30 for edge columns and
200
20 for corner columns = 1+ ...7(b)
c = ratio of longest column dimension to shorter d
column/capital dimension. u 1 = length of the critical perimeter at 2d from the
column, Fig 3
In the comparison presented in this paper, the measured
strength at the day of the test is substituted for f c or fck. = x y ...7(c)
The Australian code AS 3600 (clause 9.2.3) provisions are In the ultimate limit state the partial safety factor is 1.5.
similar to Equations (1) and (2)14. For the calculation of punching load capacity, Equation (7) is
multiplied by 1.5, which gives Equation (8)
Indian code provisions11
F sd = 0.18 (100 fck)1/3 u1d ...(8)
The Indian code provisions are also based on the American
code. As per the Indian code, the ultimate shear strength for In the comparison of this study, measured concrete
slabs without prestress is given by (clause 31.6.3.1 of the strength is taken as fck.
code)
Vuo = udc ...(3) Euro code 2 provisions18
The Eurocode provisions are similar to the British code
where,
provisions. As per Eurocode, the punching shear strength of
c = ks (0.25 fck ) ...(4) the slab is given by18
ks = 0.5 +c 1.0 ...4(a)
V Rd, c =
0.18
ck
1
(
(1001 fck )3 + 0.10cp Vmin + 0.10cp ) ...9(a)
The other terms have been defined already.
where,
British code provisions15
The British code provisions are based on the work by Regan16. 200
k =1+ 2.0, d in mm ...9(b)
As per the British code BS 8110, the ultimate shear strength of d
slabs without pre stress is given by
1 = ly .lz 0.02 ...9(c)
Vuo = udc ...(5)
where, ly. lz relate to the bonded tension steel in x and y directions
1 1
respectively. The values ly and lz should be calculated as
0.79 100 As 3 400 4 mean values taking into account a slab width equal to the
c = ...(6) column width plus 3d each side.
m bd d