Professional Documents
Culture Documents
800.851.2961
775.885.1443
The Cable Connection Fax: 775.885.2734
52 Heppner Drive E-mail: info@ultra-tec.com
Carson City, Nevada 89706 www.ultra-tec.com
PUSH-LOCK
or PULL-LOCK INVISIWARE
RECEIVER
ADJUST-A-BODY
WITH HANGER BOLT
PUSH-LOCK
LAG
LAG EYES
PUSH-LOCK ADJUST-A-BODY
ADJUST-A-BODY
with with
with EXTENDED
THREADED EYE THREADED EYE
HANGER BOLT
PUSH-LOCK
EXTENDED LENGTH LAG
Continuing a Cable Run Through a Corner
When taking cable railing through a corner, do not
bend the cable past 45 at any time. If turning 90, a
2-step turn using a double corner post configuration
is required, as illustrated. For wood frame cable runs TO
with up to 90 of turn, kits with single tensioners are END
POST
sufficient. If going through corners totaling more
than 90, you will want to use a kit with tensioners
at both ends.
Corners require two posts because the cable itself,
being rigid, will not cooperate in bending cleanly
through a single post. When you go through a corner
post, you will need to prevent the cable from slicing
into the wood as it exits the post on an angle by
using a Post Protector Tube. If using wood posts with
composite sleeves, you will want to use cable supports
instead, which reside on the outside of the sleeve,
lagging through it to the wood posts beneath.
Warranty: Stainless steel hardware and cable are covered by a limited warranty for a period of ten (10) years
from the date of receipt to be free from defects due to defective materials and workmanship.
For complete warranty details, please visit http://thecableconnection.com/warranty-ultra-tec.html
5
Run #3
Run #2
post to outside-of- Pre-attached
swaging stud
post configuration Delrin washers
Pull-Lock
for all runs. This Fitting
with cap
Invisiware
is both the most
Receiver
outside outside
mount mount
economical Stainless Steel washers Run #1
outside outside
solution and mount mount
where the fittings Series 262
are least visible.
262 Series
House
Applicable kit is Series 262 Kits 3min.
the 262 Series.
The tensioning
Cable
Length
1/8 cable 3/16 cable
PART NO. PART NO.
outside
mount
Deck 2
device is a 3 long 5 26205 26205-6
Invisiware Receiver, 10 26210 26210-6
which installs through 15 26215 26215-6
the wood post on one 20 26220 26220-6
end. A Pull-Lock fitting 25 26225 26225-6 Post Protector
Tubes in outside
is installed through the 30 26230 26230-6 Wood Posts mount
40 26240 26240-6
other end.
50 26250 26250-6
Series 262
Cable Runs through Two Corners For Post Protector Tubes, see Tools and Essentials section.
devices are a 3
Push-Lock Stud
Delrin washers
long Invisiware Invisiware
Post Protector Post Protector
Receiver
Receiver, which Tubes in Tubes in
Wood Posts Wood Posts
installs through the Stainless Steel
washers Invisiware
post on one end, and Receiver
is threaded into a 1
long Receiver. Series 272 Kits
Tools needed for 262 and 272 Series:
5/32 drill bit if 1/8 cable, 7/32 if 3/16
Cable 1/8 cable 3/16 cable
Length PART NO. PART NO. 29/64 drill bit for Receiver and Pull-Lock installation
30 27230 27230-6 3/16 Hex wrench for tensioning Receiver
40 27240 27240-6 Cable cutting tool
50 27250 27250-6 If using Post Protector Tubes, 1/4 drill bit
60 27260 27260-6 If 272 Series, 3/8 wrench for Push-Lock Stud
6
Run #3
Run #2
Series 601
Deck 2 has shared corner posts, but the posts next
outside outside
to the house are placed such that the back side of mount mount
the posts are accessible, so for Runs #2 and #3, you
will attach to the inside of the corner posts and run Run #1
3min. 3min.
Applicable kit is the 601 Series
The tensioning
outside
mount
Deck 2 outside
mount
Run #3
swaging stud
Receiver, which Series 601
installs through
the wood post on Invisiware
Receiver
Push-Lock
Lag
inside inside
one end. A Push- mount Run #1 mount
Lock Lag is lagged Series 262
into the other end.
Stainless Steel washer
for use with wood post
601 Series
House
1/8 or 3/16
1x19 stainless
steel cable Series 672
For Post Protector Tubes, see Tools and Essentials section.
Adjust-a-Body Receiver with
with Push-Lock Stud
Hanger Bolt
Run #2
Run #3
steel cable
inside inside
the corner post mount Run #1 mount
going back toward Series 262
the house to keep
the cables on the
same plane. They 300 Series House
also connect to the
inside of the posts next
to the house as well.
Series 300 Kits inside
mount
Deck 2
Cable 1/8 cable 3/16 cable
Length PART NO. PART NO.
Applicable kit is the 5 30005 30005-6
300 Series. 10 30010 30010-6
The tensioning device is 15 30015 30015-6 Post Protector
an Adjust-a-Body with 20 30020 30020-6 Tubes in inside
Wood Posts mount
25 30025 30025-6
Hanger Bolt, which lags
30 30030 30030-6
into the wood post on 40 30040 30040-6
one end. A Push-Lock Series 300
50 30050 30050-6
Lag is lagged into the For Post Protector Tubes, see Tools and Essentials section.
other end.
House
Applicable kit is
1/8 or 3/16
the 371 Series. 1x19 stainless
steel cable
The tensioning Post Protector Post Protector
Tubes in Tubes in
devices are an Push-Lock
Turnbuckle with Wood Posts Wood Posts
Adjust-a-Body with Adjust-a-Body
with
Hanger Bolt
Series 371
lags into the wood
For Post Protector Tubes, see Tools and Essentials section.
post on one end,
and Push-Lock Series 371 Kits
Turnbuckle with Cable 1/8 cable 3/16 cable
Hanger Bolt on the 371 Series For Tools needed, Length PART NO. PART NO.
other end. see bottom of
30 37130 37130-6
40 37140 37140-6
page 8. 50 37150 37150-6
60 37160 37160-6
9
Adjust-A-Body
with 1/8 and 3/16
Threaded Eye 1x19 stainless
steel cable
Pre-attached
swaging
ferrule Push-Lock
Threaded
Eye
SC-6 Screw
500-W Series
Pre-attached
swaging stud
262 Series
11
12
Series 371-C
For corner applications, see page 4.
For Cable Supports, see Tools and Essentials section.
1/8 or 3/16
1x19 stainless
steel cable
Adjust-a-Body Push-Lock
with Turnbuckle
Tools needed for 300-C (page 12) and 371-C Series: Extended
Length
with
Extended
Hanger Bolt Length
5/32 drill bit if 1/8 cable, 7/32 if 3/16 cable Hanger Bolt
13
Cable Support on
Wood Post with
Adjust-A-Body Composite Sleeve
with 1/8 and 3/16
Threaded Eye 1x19 stainless
steel cable
Pre-attached
swaging
ferrule Push-Lock
Threaded
Eye
Extended Length
Lag Eyes
SC-6 Screw
SC-6 Screw
500-C Series
14
For stairs, pitched runs: Warranty: Stainless steel hardware and cable are covered by a
100 Series (outside to outside) limited warranty for a period of ten (10) years from the date of
receipt to be free from defects due to defective materials and
7 long threaded stud to Pull-Lock workmanship.For complete warranty details, please visit
with beveled washers http://thecableconnection.com/warranty-ultra-tec.html
(BW-.250-32 for stud, BW32-6W for Pull-Lock).
15
Stainless Steel
Post Protector Tube
The post protector tube is inserted into a wood post
where the cable enters/exits the post at an angle to
keep the cable from biting into the wood.
Order CS-TUBE-6 for 1/8 and 3/16 dia. cable
TO
END
POST
17
For burr-free
cutting of cable.
For light-duty use to cut
1/8 diameter cable,
order C-7HIT Stainless Steel Cleaner
To cut cable up to and Protectant
1/4 diameter, order C-9 Dissolve minor corrosion,
then leave a protective
coating that lasts for months.
Includes an 8-oz. spray-on
Cable Release rust and stain remover and a
4-oz. bottle of protectant.
Releases cable from Push-Lock
and Pull-Lock type fittings before Order E-Z Clean
cables are tensioned.
For 1/8 cable only.
Order PL-KEY
18
272 Series
700 Series*
773 Series
401 Series
471 Series
hers
vele d was
with be
eries*
200 S
s
Serie
500-M
Warranty: Stainless steel hardware and cable are covered by a limited warranty for a period of ten (10) years
from the date of receipt to be free from defects due to defective materials and workmanship.
For complete warranty details, please visit http://thecableconnection.com/warranty-ultra-tec.html
19
If composite sleeve, what is the outside diameter What diameter cable are you using
when installed? (1/8 or 3/16)?
Looking for your nearest source for Ultra-tec Cable Railing Kits?
Visit our Website:http://thecableconnection.com/wholesalers.html or scan this QR code with your smartphone.
You will be directed to wholesalers in your state who can point you to a participating local retailer.