Professional Documents
Culture Documents
Astm A 27-13
Astm A 27-13
Copyright by ASTM Int'l (all rights reserved); Wed Oct 22 14:41:57 EDT 2014
2
Downloaded/printed by
Vernica Meza (DICTUC S.A.) pursuant to License Agreement. No further reproductions authorized.
A27/A27M 13
must be defined. If postweld heat-treatment is not required,
Class 2 must be specified along with the grade.
10. Keywords
10.1 castings; general application; steel
SUPPLEMENTARY REQUIREMENTS
The following supplementary requirements shall not apply unless specified in the purchase order. A
list of standardized supplementary requirements for use at the option of the purchaser is included in
Specification A781/A781M for sand castings, or in Specification A957/A957M for investment
castings. Those which are ordinarily considered suitable for use with this specification are given
below. Others enumerated in Specification A781/A781M or in Specification A957/A957M may be
used with this specification upon agreement between the manufacturer and purchaser.
S1. Magnetic Particle Examination S52. Gate and Riser Projections for Castings Made from
Mounted Patterns
S2. Radiographic Examination
S52.1 Castings shall have gates and risers removed in such
S3. Liquid Penetrant Examination a manner that no riser or gate stub projects or a depression is
made beyond or below the casting design contour in an amount
S4. Ultrasonic Examination that would exceed the values given in Table S52.1.
Copyright by ASTM Int'l (all rights reserved); Wed Oct 22 14:41:57 EDT 2014
3
Downloaded/printed by
Vernica Meza (DICTUC S.A.) pursuant to License Agreement. No further reproductions authorized.
A27/A27M 13
S54.2 Total content of these residual elements, maximum
percent 1.00.
SUMMARY OF CHANGES
Committee A01 has identified the location of selected changes to this standard since the last issue
(A27/A27M10) that may impact the use of this standard. (Approved Nov. 1, 2013.)
(1) Removed A732/A732M as a reference. (6) Supplementary Requirements: Replaced first paragraph
(2) Added A1067/A1067M as a reference. with wording similar to that now used in other steel casting
(3) 6.1, Added or Specification A957/A957M after A781/ specifications.
A781M. (7) S54.1, Added or Specification A957/A957M after A781/
(4) 7.2, Replaced A781/A781M with A1067/A1067M. A781M.
(5) 7.7 Deleted.
ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned
in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk
of infringement of such rights, are entirely their own responsibility.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and
if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards
and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the
responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should
make your views known to the ASTM Committee on Standards, at the address shown below.
This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,
United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above
address or at 610-832-9585 (phone), 610-832-9555 (fax), or service@astm.org (e-mail); or through the ASTM website
(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/
COPYRIGHT/).
Copyright by ASTM Int'l (all rights reserved); Wed Oct 22 14:41:57 EDT 2014
4
Downloaded/printed by
Vernica Meza (DICTUC S.A.) pursuant to License Agreement. No further reproductions authorized.