Professional Documents
Culture Documents
RRC Fail Counter Analysis
RRC Fail Counter Analysis
and other Huawei trademarks are the property of Huawei Technologies Co., Ltd. All other trademarks
and trade names mentioned in this document are the property of their respective holders.
Notice
The purchased products, services and features are stipulated by the commercial contract made between
Huawei and the customer. All or partial products, services and features described in this document may not be
within the purchased scope or the usage scope. Unless otherwise agreed by the contract, all statements,
information, and recommendations in this document are provided AS IS without warranties, guarantees or
representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute the warranty of any kind, express or implied.
Contents
1 Introduction ................................................................................................................................1-1
1.1 Scope ............................................................................................................................................ 1-1
1.2 Intended Audience ........................................................................................................................ 1-1
1.3 Change History.............................................................................................................................. 1-1
4 Parameters .................................................................................................................................4-1
5 Counters......................................................................................................................................5-1
6 Glossary ......................................................................................................................................6-1
7 Reference Documents .............................................................................................................7-1
1 Introduction
1.1 Scope
This document describes the high-speed uplink packet access (HSUPA) transmission time interval (TTI)
selection feature. It covers both the TTI selection during service setup or reconfiguration and the
dynamic TTI adjustment, and furthermore provides parameter descriptions.
Document Issues
The document issues are as follows:
z 01 (2010-03-30)
z Draft (2009-12-05)
01 (2010-03-30)
This is the document for the first commercial release of RAN12.0.
Compared with issue Draft (2009-12-05) of RAN12.0, this issue optimizes the description.
Draft (2009-12-05)
This is the draft of the document for RAN12.0.
This is a new document.
3 Technical Description
3.1 TTI Selection During Service Setup or Reconfiguration
The TTI for a service over HSUPA can be set to 2 ms or 10 ms. When the service is set up or
reconfigured, the RNC determines the TTI according to the rules listed in Table 3-1.
Table 3-1 TTI selection during service setup or reconfiguration
Service Type TTI Setting
CS voice service The TTI is set to 2 ms if all the following conditions are met:
z Both the UE and the NodeB support the 2 ms TTI.
z The MAP_HSUPA_TTI_2MS_SWITCH subparameter of the MapSwitch
parameter is set to ON.
z The CSVoiceHsupaTti parameter is set to EDCH_TTI_2ms.
If one of the conditions is not met, the TTI is set to 10 ms.
PS voice service The TTI is set to 2 ms if all the following conditions are met:
z Both the UE and the NodeB support the 2 ms TTI.
z The MAP_HSUPA_TTI_2MS_SWITCH subparameter of the MapSwitch
parameter is set to ON.
z The VoipHsupaTti parameter is set to EDCH_TTI_2ms.
If one of the conditions is not met, the TTI is set to 10 ms.
PS streaming service The TTI is set to 2 ms if all the following conditions are met:
z Both the UE and the NodeB support the 2 ms TTI.
z The MAP_HSUPA_TTI_2MS_SWITCH subparameter of the MapSwitch
parameter is set to ON.
z The maximum bit rate (MBR) is higher than or equal to the value of
StreamHsupa2msTtiRateThs.
If one of the conditions is not met, the TTI is set to 10 ms.
PS BE service The TTI is set to 2 ms if all the following conditions are met:
(interactive or z Both the UE and the NodeB support the 2 ms TTI.
background service)
z The MAP_HSUPA_TTI_2MS_SWITCH subparameter of the MapSwitch
parameter is set to ON.
z The cell is not congested.
z The MBR is higher than or equal to the value of BeHsupa2msTtiRateThs.
If one of the conditions is not met, the TTI is set to 10 ms.
Each service in a service combination is assigned a TTI during service setup or reconfiguration. The
service combination is assigned the 2 ms TTI as long as one service in the combination is assigned the 2
ms TTI. Otherwise, the service combination is assigned the 10 ms TTI.
z For the UE with 2ms TTI, If the uplink transmit power is insufficient and the traffic volume is relatively
low for a period, the RNC adjusts the TTI of UE to 10ms.
z For the UE with 10ms TTI, if the uplink transmit power is sufficient and the traffic volume is relatively
high for a period, the RNC adjusts the TTI of UE to 2ms.
Note that the RNC can perform dynamic TTI adjustment for a single BE service only when the HSUPA
DCCC function is disabled or ineffective. For detail information about HSUPA DCCC, see the State
Transition Feature Parameter Description.
4 Parameters
Table 4-1 Parameter description
Parameter NE MML Description
ID
BeHsupa2 BSC690 SET Meaning: Rate threshold of 2ms TTI on the E-DCH for the
msTtiRateT 0 UFRC(Optional) HSUPA PS BE service. The 2ms TTI is used on the E-DCH
hs when it is supported by the cell and UE and when the rate of the
HSUPA PS BE service exceeds this threshold. Otherwise, 10ms
TTI is used.
GUI Value Range: D8, D16, D32, D64, D128, D144, D256,
D384, D608, D1440, D2048, D2880
Actual Value Range: 8, 16, 32, 64, 128, 144, 256, 384, 608,
1440, 2048, 2880
Unit: kbit/s
Default Value: D1440
CSVoiceHs BSC690 SET Meaning: TTI type used for CS services over the uplink HSPA
upaTti 0 UFRC(Optional) channel.
GUI Value Range: D8, D16, D32, D64, D128, D144, D256,
D384, D608
Actual Value Range: 8, 16, 32, 64, 128, 144, 256, 384, 608
Unit: kbit/s
Default Value: D384
VoipHsupa BSC690 SET Meaning: TTI type used for VoIP services over the E-DCH
Tti 0 UFRC(Optional)
GUI Value Range: EDCH_TTI_10ms, EDCH_TTI_2ms
Actual Value Range: EDCH_TTI_10ms, EDCH_TTI_2ms
Unit: None
Default Value: EDCH_TTI_10ms
5 Counters
For details, see the BSC6900 UMTS Performance Counter Reference.
6 Glossary
For the acronyms, abbreviations, terms, and definitions, see the Glossary.
7 Reference Documents
[1] State Transition Feature Parameter Description