Professional Documents
Culture Documents
Prequalified Seismic Moment Connections PDF
Prequalified Seismic Moment Connections PDF
January 2007
Your connection to
ideas + answers
Variables and Denitions
341 = refers to the AISC Seismic Provisions for tst = thickness of end-plate stiffener, in.
Structural Steel Buildings, ANSI/AISC 341-05 Vgravity = required beam shear force at beam end due to
358 = refers to AISCs Prequalied Connections for gravity loads
Prequalified Seismic Moment Connections Special and Intermediate Steel Moment Frames for
Seismic Applications, ANSI/AISC 358-05
VRBS
Vweb
= shear force at center of RBS [358-5.4(2a)]
= required shear force at beam web-to-column
360 = refers to the AISC Specication for Structural connection, kips
Heres a visual summary of the seismic requirements Steel Buildings, ANSI/AISC 360-05 Ze = effective plastic section modulus of the beam
CJP = complete joint penetration groove weld cross section at the location of the plastic
for two prequalied moment connections. EEP = extended end-plate connection hinge, in.3
IMF = intermediate moment frame Ze(RBS) = Zx 2ctbf (db tbf), in.3 [358 Eq (5.8-4)]
BY GREGORY KOCHALSKI AND JASON ERICKSEN, S.E. RBS = reduced beam section connection Zx = plastic section modulus of the full beam cross
T
SMF = special moment frame section about the x-axis, in.3
TOS = top of steel beam
The new standard, Prequalied Connections for Special and Inter- Reduced Beam Section (RBS) Moment Connection a = horizontal distance between a column ange User Notes:
mediate Steel Moment Frames for Seismic Applications (ANSI/ (Chapter 5): Portions of the beam ange are selectively and the start of an RBS cut, in. Demand Critical Welds are welds that require increased
AISC 358-05), has arrived. trimmed in the region adjacent to the column-beam con- b = length of an RBS cut, in. ductility requirements. See 341-7.3b for specic require-
Special Moment Frame (SMF) and Intermediate Moment nection to ensure yielding and hinge formation within the bbf = width of beam ange, in. ments.
Frame (IMF) structural steel systems designed in accordance reduced area. This connection type can be used for SMF and bp = width of the end-plate, in. all welds per 341 Appendix W, 341-7.3, and 358 Chapter
with the AISC Seismic Provisions for Structural Steel Buildings IMF systems. c = depth of an RBS cut at the center of the 3.
(ANSI/AISC 341-05) are required to have beam-to-column Bolted Unstiffened and Stiffened Extended End- reduced beam section, in. all bolts per 358 Chapter 4 (ASTM A325 and A490, or
connections that satisfy the requirements of Section 9.2 for Plate (EEP) Moment Connections (Chapter 6): By weld- Cf = distance from the centerline of the column equaivalent twist-off, high-strength bolts allowed).
SMF or 10.2 for IMF. These requirements include a mini- ing the beam to an end-plate and bolting one of three end- web to the end of the ange clip in a The effective beam ange width for compactness can be
mum interstory drift angle each connection must be capable plate congurations to the column the connection ensures continuity plate, in. taken as 2[c R + (R2 + b2/9)0.5] per 358-5.3.1(6).
of sustaining, a minimum exural resistance at that drift angle, that inelastic deformation of the connection is achieved by Cpr = (Fyb + Fub)/2Fyb 1.2 [358 Eq. (2.4.3-2)] See 341 Commentary Figure C-I-7.2 and Section 9.5
and a minimum shear strength based on full yielding of the beam yielding when designed in accordance with these provi- Cw = distance from the outside face of column for continuity plate details.
moment connection at each end of the beam. There are two sions. This connection type can be used for SMF and IMF ange to the end of the web clip in a See 341 Commentary C8.5 for column base plate
ways to demonstrate that these criteria have been met: systems; however it is not currently permitted to be used for continuity plate, in. details.
Provision of qualifying test results in accordance with SMF when a structural concrete slab is in contact with the db = depth of the connecting beam, in. See 341 Commentary C9.3 and Figure C-I-9.3 for panel
Appendix S of the Seismic Provisions. beam, unless the slab is isolated from the beam. dc = depth of column, in. zone doubler plate details.
Use of a connection prequalied in accordance with The following details are a visual representation of Fub = specied minimum tensile strength of a beam, See 341-9.7 for lateral bracing requirements for the
Appendix P of the Seismic Provisions, such as those in the the major requirements of the Seismic Provisions and the ksi beam-to-columns connecitons.
prequalied connections standard. prequalied connections standard. These two documents con- Fyb = specied minimum yield stress of a beam, ksi
The rst option requires that the engineer of record sub- tain the detailed design requirements and should be consulted Fyc = specied minimum yield stress of a column, ksi
stantiate the ability of the connection to meet the require- on each design. The often-overlooked commentary on the = gage, the horizontal distance between bolts, in.
ments of section 9.2 or 10.2 and prove that the tests were Seismic Provisions and the prequalied connections standard
g Other Important Sections
k1 = distance from web center line to ange toe of
performed according to Appendix S. Tests involve additional can prove extremely helpful and offers guidance concerning 1. 341-6.3 Heavy Section CVN Requirements:
llet, in.
expense and the engineer must convince the authority having the intent and application of the requirements. Make sure to Special CVN requirements exist for hot-rolled
kdet = distance from outside face of ange to the web
jurisdiction that all the requirements are met, but this may visit www.aisc.org/freePubs for free pdf les of the Seismic shapes with anges greater than or equal to 1.5
toe of llet, based on the largets llet used in
still be a viable option. Tests reported in literature performed Provisions and the prequalied connections standard. in. thick and for plates 2 in. thick and thicker.
production, in.
in accordance with Appendix S can also be used, but demon- Lb = distance between brace points, in. 2. 341-7.2 Bolted Joints: All bolts shall be
strating the applicability of those tests still rests on the engi- Gregory Kochalski is a senior in architectural engineering at Penn Lst = length of end-plate stiffener, in. pretensioned and have Class A faying surfaces,
neer of record. State University and a former AISC engineering intern. Jason M*pb for EEP: M*pb = (1.1RyFyZb + Mv) [341-9.6] even though they are designed for bearing shear
The second option requires that a prequalication panel is Ericksen is director of AISCs Steel Solutions Center. for RBS: M*pb = (Mpr + Mv) [358-5.4] values. Faying surfaces for end-plate connections
set up and approved by the authority having jurisdiction. This M*pc = Zc(Fyc Puc /Ag) [341-9.6] are permitted to be painted with coatings without
panel must then create guidelines and approve connections Mpe for EEP: Mpe = CprRyFyZx [358 Eq (6.9-3)] a Class A rating.
based on test data to be prequalied. for RBS: Mpe = RyFyZx [358 Eq (5.8-7)] 3. 341-7.2 Bolted Joints: Bolts and welds shall not
AISCs Connection Prequalication Review Panel (CPRP) Mpr = CprRyFyZe [358 Eq (2.4.3-1) also 5.8-5] share a force in a joint or a force component in a
reviews connection test data and prequalies connections in Notes Mv = VRBS(a + b/2 + dc/2) [358-5.4(2a)] connection.
accordance with Appendix P. The result is the prequalied R = radius of an RBS cut, in.
1. Details shown are for hot-rolled wide-ange mem- 4. 341-7.3b contains the requirements for demand
connections standard. This document is specically permit- Ryb = ratio of the expected yield stress of the beam
bers. For built-up members see Sections 2.3.2, 2.4.4, critical welds.
ted to be used in the Seismic Provisions. The CPRP continues material to the specied minimum yield stress,
5.3.1(2), and 5.3.1(3) of the prequalied connections 5. 341-7.4 contains the requirements for protected
to review connections and will release a new chapter for each per the AISC Seismic Provisions
standard. zones.
new prequalied connection. Using this document is cur- Ryc = ratio of the expected yield stress of the column
rently the easiest and most direct method of satisfying the 2. Although details are presented in LRFD format, cor- material to the specied minimum yield stress, 6. 341-8.4b contains the requirements for columns
conformance demonstration requirements for SMF and IMF responding to the format of ANSI/AISC 358-05, the per the AISC Seismic Provisions splices for columns not part of the seismic load
connections in the Seismic Provisions. connections can be designed with ASD provisions as tbf = thickness of beam ange, in. resisting system.
The prequalied connections standard offers the follow- well. tcf = column ange thickness, in. 7. 341-8.5 contains the requirements for column
ing connections to choose from when designing IMF and tsp = thickness of shear plate, in. bases.
SMF systems: