Professional Documents
Culture Documents
Practice Exam 1 AM (A) Solutions
Practice Exam 1 AM (A) Solutions
AM (A)
Solutions
Practice Exam 1
AM (A)
Practice Exam 1
AM (A)
Solutions
Q. 1
A storm drain inlet for a 2.7 acre parking area is to be designed. The rainfall intensity is 8.6 in/hr
and the runoff coefficient is 0.96. The peak discharge, in cubic feet per second, is most nearly:
(A) 18
(B) 19
(C) 20
(D) 22
Solution
Given:
C = 0.96
I = 8.6 in/hr
A = 2.7 acre
Qp = C*I*A = 0.96*8.6*2.7 = 22.3 ft3/sec
THE CORRECT ANSWER IS (D)
Practice Exam 1
AM (A)
Solutions
Q. 2
The cantilevered retaining wall shown is under design. What is most nearly the active resultant
per unit length of wall?
118.4lbf / ft 3
31o
Q. 3
The maximum specific energy in a rectangular channel is 9 feet. The critical velocity, in ft/sec,
is most nearly:
(A) 8.7
(B) 12.3
(C) 14.1
(D) 15.4
Solution
Solve for the critical depth, which will allow you to solve for the critical velocity.
dc = 2/3 Ec = 2/3 * 9 = 6 feet
vc = (gdc)1/2 = (32.2 * 6)1/2 = 13.9 ft /sec
THE CORRECT ANSWER IS (C)
Practice Exam 1
AM (A)
Solutions
Q. 4
A 10ft by 10ft square, reinforced concrete footing is installed so that the footing bearing surface
is 5 ft below the soil level, at a point where the allowable soil pressure is 3500 psf. Other than
the soil above the footing, there is no surcharge. The soil unit weight is 100 lbf/ft3. The footing
is located at the corner of a building and is loaded through a concentric 14 in square column.
The column transmits a 125,000 lbf service dead load and a 175,000 lbf service live load to the
footing. The critical (plan) area contributing to two-way punching shear is assumed to be
92.44ft2.Th ede adl oa dinc l
ude sthec ol
umn swe ightbutdoe snoti ncludet hef oot i
ngswe i
ght.
The compressive strength for all of the concrete used is 3000 psi.
The ultimate two-way punching shear, in lbf, is most nearly?
(A) 350,000
(B) 450,000
(C) 550,000
(D) 650,000
Solution
The footing area is
A B 2 (10 ft )(10 ft ) 100 ft 2
The ultimate load carried by the footing is
P 1.4 Pd 1.7 Pl
(1.4)(125, 000 lbf)+(1.7)(175,000 lbf)
472,500 lbf
The factored soil pressure acting on the footing is
P 472, 500 lbf
pu u
A 100 ft 2
4725 lbf/ft 2
The ultimate two-way punching shear is
lbf
Vu pu Acritical 4725 2
ft
92.44ft 2
150
CONTACT
TIME, t10
100
(min)
50
0 1 2 3 4 5 6 7
TABLE 1
Parameter Value
Turbidity 17 NTU
pH 6.8-7.1 S.U.
Alkalinity 150 mg/L as CaCO3
Calcium 51 mg/L as CaCO3
Temperature 10C to 26 C
Practice Exam 1
AM (A)
Solutions
TABLE 2
CT values (mg/L
min) for inactivation of Giardia cysts by free chlorine at 10
C
Chlorine pH=7.0
Concentration Log Inactivations
(mg/L) 0.5 1.0 1.5 2.0 2.5 3.0
0.4 18 33 33 70 82 105
0.6 19 38 56 75 94 113
0.8 20 40 59 79 99 119
1.0 21 41 62 82 103 123
1.2 21 42 64 85 106 127
1.4 22 44 65 87 109 131
1.6 22 45 67 89 112 134
1.8 23 46 68 91 114 137
2.0 23 46 70 93 116 139
2.2 24 47 71 95 118 142
2.4 24 48 72 96 120 144
2.6 24 49 73 97 122 146
2.8 25 49 74 99 123 148
3.0 25 50 75 100 125 150
Source: U.S. Environmental Protection Agency, Guidance Manual for Compliance with
Filtration and Disinfection Requirements for Public Water Systems Using Surface Water
Sources, Criteria and Standards Division, Office of Drinking Water (U.S.E.P.A. NTIS
Publication NO. PB 90-148016), Washington, D.C: U.S. Government Printing Office, October,
1979.
Solution
Surface Water Treatment Rule for disinfection of Giardia; 3 log inactivation required. 2.5 log
inactivation allowed for treatment prior to disinfection. Therefore, 3-2.5 = 0.5 log inactivation
required by disinfection.
From the figure, at a peak hourly flow rate of 5 MGD, t10 = 50 min contact time.
CT 23 mg / L min; CT concentration x time
Ref: Davis 7 Cornwell, Environmental Engineering, McGraw Hill, 1998, p. 244, Table 3-20.
C = CT/T (23 mg / L min) / 50 min 0.46 mg / L residual chlorine concentration needed.
THE CORRECT ANSWER IS: (C)
Practice Exam 1
AM (A)
Solutions
Q. 6
An eight phase intersection looses 2 seconds per phase and has an all-red duration of 3 seconds
on phases 1 and 4. If the sum of the ratios of approach flow to saturation flows for all phases is
0.7(i.e .t
hef lowt os atur at
ionf l
owsf ora l
lpha sesis0.7( i.
e.the" Y"va lue )
,thent heopt i
mum
cycle time, in seconds, is most nearly:
(A) 80
(B) 95
(C) 105
(D) 125
Solution
1 5 L 5
Co o
1 y
i 1
where
Co = optimum cycle time (sec)
L = total lost time per cycle (sec)
yi = maximum value of approach flows to saturation flows for all lane groups using
phase i, qij/s;
L i R
i 1
2 8 2 3
= 22 sec
(1.5 22) 5
Co
1 0.7
= 126.7 sec
THE CORRECT ANSWER IS (D)
Practice Exam 1
AM (A)
Solutions
Q. 7
Ifthede pthoff l
owi ngwa t
e rinadi tchwi thMa nningsroug hnessof0. 02a nda
nave
rag
ebe
d
slope of 0.5% is 2 feet, the velocity (fps) of the water would be most nearly:
(A) 3.5
(B) 3.8
(C) 5.6
(D) 6.8
1 1
3 3
2' - 0"
DITCH SECTION
NOT TO SCALE
Solution
Determine the water velocity for the trapezoidal ditch. For a depth = 2.0 ft.
A
2.0 3x2.0
2.0 16.0 ft 2
R
b zy y 2.0 3x2.0 2.0 1.092 ft
b 2 y 1 z 2 2.0 2x2.0 1 32
1.486 2 3 1 2 1.486
x
1.092 3
0.005 2 5.6 ft / s
2 1
V R s
n 0.02
THE CORRECT ANSWER IS: (C)
Practice Exam 1
AM (A)
Solutions
Q. 8
Analyze the truss shown.
h
2
h
2
By summing the forces in the horizontal direction, determine that the horizontal reaction at A is
zero.
The sum of the forces in the vertical direction is
AH v RA,v 0 lbf
Practice Exam 1
AM (A)
Solutions
AHv = 300 lbf (compression)
From the geometry of the truss, the horizontal component of AH must be twice the vertical
component.
AHh = (2)(300 lbf)
= 600 lbf (compression)
The resultant force in member AH is
AH AH v2 AH h2
(300 lbf) 2
600 lbf
2
Q. 9
A city wants to design a sludge dewatering system for their 20-MGD secondary, activated sludge
treatment plant shown below.
The sludge volume reduction (%) achieved by the thickener is most nearly:
(A) 50
(B) 58
(C) 65
(D) 70
BOD f =5mg/L
TSS1 =200mg/L TSSPE =80mg/L TSSf =10mg/L
Solution
Assuming specific gravity of sludge is 1.00
Sludge quantity and volume to be dewatered.
Primary Sludge
lb / d (200 mg / L 80 mg / L)(8.34)(20 MGD ) 20, 016 lb / d
20, 016 lb / d
gpd 68.571 gpd
(8.34 lb / gal )(0.035)
Secondary Sludge (was)
10, 000 lb / d
gpd 0.1599 MGD 0.159,872 gpd
(8.34 lb / gal )(7,500 mg / L)
Before Thickening
Total quantity = 20, 016 10, 000 30, 016 lb / d
Total volume = 68,571+159,872 = 228,443 gpd
Practice Exam 1
AM (A)
Solutions
After Thickening
Total quantity = 30,016 lb/d
30, 016
Total volume 79,979 gpd
(8.34 lb / gal )(0.045 percentage)
228.443-79,979
% R eduction in sludge volume= 65%
228.443
CORRECT ANSWER IS: (C)
Practice Exam 1
AM (A)
Solutions
Q. 10
Groundwater monitoring wells have been installed at the site of a proposed sanitary landfill such
that Well B is located 1,500 feet north and 300 feet west of Well A.
A proposed containment cell, having bottom dimensions of 500 feet (north to south) and 100 feet
(east to west), is to be located such that the southeast corner is 100 feet west and 500 feet north
of Well A.
The bottom of the landfill cell must be a minimum of 5 feet above the groundwater elevation.
The elevations that were determined at each well location are shown in the table below.
The minimum bottom elevation for the proposed landfill cell if the bottom is to be level is most
nearly:
(A) 227
(B) 232
(C) 237
(D) 242
Solution
Determine minimum bottom elevation of the containment cell.
The highest groundwater elevation within cell area = groundwater elevation at point A less the
groundwater drop to closest point of the cell, Point C highest groundwater elevation within cell
area = groundwater elevation at Point A less the (distance A to C)*I
Distance Well A to cell [(500) *(500) (100)*(100)0.5 ] 510 ft
Highest groundwater elevation within cell area 229.75 510* 0.0049 227.25
Minimum bottom elevation of containment cell = highest groundwater elevation within cell area
plus 5 feet = 227.25 + 5 feet
Minimum bottom elevation of containment cell = 232 feet
A soil sample, taken from a borrow pit has a specific gravity of soil solids of 2.66. The sample
was taken to a materials laboratory and tested. The results of a standard Proctor test are
tabulated below.
(A) 85
(B) 90
(C) 100
(D) 115
Solution
Step 1: Derive unit weight (of wet soil) from:
= weight of soil/volume of proctor mold,
where volume of proctor mold = 1/30 ft3.
d / (1+w)
96 11% 86
113 13% 100
132 15% 115
123 17% 105
111 18% 94
99 19% 83
120
115
(lb/ft3)
110
d
105
Dry unit weight,
100
95
90
85
80
10% 12% 14% 16% 18% 20%
Moisture Content, w (% )
A horizontal curve for a section of a highway has a design speed of 60 mph. The terrain restricts
the radius of the curve to 1200 ft, which therefore requires the super elevation at the curve, in
percent, to be most nearly:
(A) 4
(B) 6
(C) 8
(D) 10
Solution
u2
Radius ( ft )
15(e f s )
Given the radius of 1200 feet and the design speed of 60 mph, the side friction factor (fs) comes
from Exhibit 3-14onpa ge145oft he2001AASHTO APol icyonGe ome tri
cDe signof
Hi g
hwa ysa ndSt reetswhi chi sba s e
donthede si
g ns peed.Iti ndicatest ha tfora60mphde si
gn
speed the side friction factor is 0.12
fs = 0.12
Substituting the known values into the radius equation, the only unknown is the super elevation,
e. By solving for e, the super elevation rate is found.
(60mph) 2
1200 ft
15(e 0.12)
602 3600
e 0.12 e 0.12 0.08 8%
1200(15) 1200(15)
THE CORRECT ANSWER IS ( C )
Practice Exam 1
AM (A)
Solutions
Q. 13
A horizontal curve is defined by its radius of 851 feet, as shown below. The length of the chord
AB, in feet, is most nearly:
A B
12%
36o
(A) 505
(B) 515
(C) 525
(D) 535
Solution
sin 36
2
AD
AO
AD C / 2
Practice Exam 1
AM (A)
Solutions
AO R 851
C 2(851)sin(18) 525.95
2851
Arc ACB= 534.70
360
THE CORRECT ANSWER IS (C)
Q. 14
A concrete column and footing caries the loads shown.
The footing is 6 ft wide.
column dead load 80 kips
column live load 100 kips
moment due to wind 50 ft-kips
compressive strength of concrete 3000 lbf/in2
maximum allowable soil pressure 3000 lbf/in2
What is the minimum footing length, L, required for the entire footing to be considered effective
in carrying these loads?
(A) 1.7 ft
(B) 1.8 ft
(C) 7.7 ft
(D) 10 ft
Hint: For the entire footing to be effective, avoid tensile stress in the soil.
Practice Exam 1
AM (A)
Solutions
Solution
Limit eccentricity, e, to one-sixth of the footing length to keep the soil resultant within the kern
limit and avoid tension in the soil.
M M
e wind
P PD PL
50 ft kips
80 kips 100 kips
= 0.28 ft
L
e
6
L
0.28 ft
6
Solving for L,
L
0.28 ft
6 1.68 ft
1.7 ft
THE CORRECT ANSWER IS (A)
Why Other Options Are Wrong
(B) This incorrect solution calculates eccentricity using factored loads. Factored loads are used
in concrete design, but not for determining footing size. Footing size should be based on
unfactored soil pressure.
(C) This incorrect solution calculates the required size of a square footing (ignoring the footing
width given) based on the dead and live loads and allowable soil pressure. The problem
statement is asking for the minimum length required for the entire footing to be effective, not the
minimum size based on the soil pressure.
(D) This incorrect solution calculates the required length based on the dead and live loads and
allowable soil pressure. The problem statement is asking for the minimum length required for
the entire footing to be effective, not the minimum size based on the soil pressure.
Practice Exam 1
AM (A)
Solutions
Q. 15
The mechanical and plasticity tests of a soil under consideration as a fill material are shown
below:
A soil is under investigation. Mechanical and plasticity test results are shown below:
The soil may be classified, according to the Unified Soil Classification (USCS) system as:
(A) GP
(B) SW
(C) CL
(D) CH
Solution
Refer to the Unified Soil Classification System, Technical Memorandum No. 3-357, US Army
Engineers Waterways Experiment Station, Vicksburg, Mississippi, 1960. Note, this
classification table is reproduced in most geotechnical textbooks. You will find it typically titled
as TheUni fiedSoi lCl assi
ficat
ionSy stem .
(A) 100 + 00
(B) 100 + 25
(C) 101 + 00
(D) 102 + 50
Solution
Q. 17
Using the NDS, which of the following statements must be true?
I. The temperature factor, Ct, applies to member subjected to extremely cold
temperatures.
II. The volume factor, CV, applies only to glued laminated timber bending members.
III. The bending design value, Fb, for a floor framed with 1 x 6 sawn lumber joists must
be multiplied by the repetitive member factor.
IV. The load duration factor, CD, does not apply to the modulus of elasticity values.
(A) I and II
(B) II and III
(C) II and IV
(D) III and IV
Hint: Refer to NDS Sec 2.3 for adjustment of design values.
Solution
Section 2.3 and Table 2.3.1 of the NDS contain the adjustment factors and their applicability for
design values.
The volume factor, CV, is discussed in the footnotes to NDS Table 2.3.1. Footnote 3 states, "The
volume factor, CV, shall apply only to glued laminated timber bending members (see Sec.
5.3.2)." Statement II is true.
The load duration factor, CD, is discussed in NDS sec. 2.3.2 and NDS table 2.3.2. Both NDS
Sec. 2.3.2.1 and Footnote 1 to NDS Table 2.3.2 state that "Load duration factors shall not apply
t
omodul usofe las
tici
ty,E"St ateme ntI Vi st
rue.
THE CORRECT ANSWER IS (C)
Why Other Options Are Wrong
(A) Although statement II is true, statement I is false. The temperature factor, Ct, is discussed in
NDS Sec. 2.3.4. The temperature factor applies to members subjected to sustained exposure to
elevated (over 100 F) temperatures. Because the statement applies to members subjected to
extreme cold, not heat, statement I is false.
(B) Although statement II is true, statement III is false. The repetitive member factor, Cr, is
discussed in Footnote 5 of NDS Table 2.3.1 Footnote 5 states, "The repetitive member factor,
Cr, shall apply only to dimension lumber bending members 2 in to 4 in thick (see Sec. 4.3.4)."
Because the joists in this case are 1 in thick, statement III is false.
(D) Although statement IV is true, statement III is false because the repetitive member factor,
Cr, applies only to dimension lumber bending members 2 in to 4 in thick. The joists in this case
are 1 in thick.
Practice Exam 1
AM (A)
Solutions
Q.-18
A soil sample weighing 66.8 lb with a moisture content of 19 percent, volume of 0.55 cubic feet,
has a specific gravity of 2.72. The degree of saturation is most nearly:
(A) 0.5
(B) 0.6
(C) 0.7
(D) 0.8
Solution
W / V
= 66.83 / 0.55
= 121.5 pcf
d / (1 + w)
d = 121.5 / (1 + 0.19)
d = 102.1 pcf
d = (Gs * w ) / (1 + e)
e = ((Gs * w ) / d ) 1
e = ((2.72 * 62.4) / 102.1) 1
e = 0.66
S = (w * Gs) / e
S = ((0.19)*(2.72)) / 0.66
S = 0.78
THE CORRECT ANSWER IS: (D)
Practice Exam 1
AM (A)
Solutions
Q. 19
What is the average hydraulic detention time for a rectangular tank with dimensions of 2.5 m by
15 m by 3.0 m deep receiving a flow of 900 m3/d? The hydraulic efficiency of the tank is 83%.
(A) 2.3 h
(B) 2.5 h
(C) 3.0 h
(D) 3.6 h
Hint: The average detention time will be less than the theoretical detention time.
Solution
E fractional efficiency -
Q flow rate m3/d
t theoretical hydraulic detention time d
ta actual hydraulic detention time d
V volume m3
h
(2.5m)(15m)(3.0m) 24
V
t d
3
Q m
900
d
3.0 h
ta tE
83%
3.0 h
100%
=2.5 h
THE CORRECT ANSWER IS (B)
(D) In this incorrect solution, the theoretical detention time is divided by the hydraulic
efficiency instead of being multiplied by it. Other definitions and equations are unchanged from
the correct solution.
2.5m)(15m)(3.0m
h
24
t d
3
m
900
d
3.0 h
100%
ta 3.0 h
83%
=3.6 h
Q. 20
Assume all soils in a drainage basin are in the Soil Conservation Service (SCS) hydrologic soil
Group B. Also assume that the vegetative covers are in good condition. The land use is parks
and open space. The SCS Runoff Curve Number (CN) for the entire area is most closely
approximated by:
(A) 43
(B) 54
(C) 61
(D) 81
Solution
Determine the SCS Runnoff Curve Number for the entire area. For soil Group B, with good
vegetative cover in urban, fully developed open space (parks, lawns), the appropriate SCS curve
number (Gupta, Hydrology and Hydraulic Systems, Prentice Hall, 1989, p. 101)
CN = 61
THE CORRECT ANSWER IS (C)