Professional Documents
Culture Documents
Honeywell Sensing Micro Switch Hdls Limit Product Sheet 002345 8 en
Honeywell Sensing Micro Switch Hdls Limit Product Sheet 002345 8 en
Tracking interchangeability
of actuator levers for single-
Twin shaft seals for an and double-pole switches,
extra measure of plug-in and non-plug-in.
protection. Optional
fluorocarbon or
fluorosilicone seals.
Dual bearings deliver
enhanced mechanical life.
Exclusive teller tab ensures
proper torque. When it cannot
be moved, the lever is tight
enough to prevent
slippage.
Boss-and-socket
head design for secure
head-to-body retention.
Each switch has four mounting holes; two through holes for front mount, and
two tapped holes in back for rear mount
2 sensing.honeywell.com
MICRO SWITCH Heavy-Duty Limit Switch, HDLS Series
Table 1. Specifications
Characteristic Parameter
Product type MICRO SWITCH heavy-duty limit switches
Side plunger - adjustable Side plunger - pin Side plunger maintained - pin
Side roller plunger Side rotary Side rotary maintained
Acutators/heads Top plunger - adjustable Top plunger - pin Top roller plunger
Top rotary Wobble - cable Wobble - cat whisker
Wobble - coil spring Wobble - plastic rod Wobble - spring wire
1NC 1NO SPDT snap action, double break
2NC 2NO DPDT center neutral, snap action, double break
Circuitry
2NC 2NO DPDT snap action, double break
2NC 2NO DPDT sequential, snap action, double break
10 A thermal
Electrical
Single and double pole: AC15 A600; DC13 R300 (see table on page 5)
Housing material Zinc die-cast with an electrostatic epoxy coating
0.5 in - 14NPT conduit 0.75 in - 14NPT conduit 12 ft cable, 6 ft cable
PG 13,5 conduit 20 mm conduit 4-pin micro-style connector
Termination types
4-pin mini-style connector 5-pin mini-style connector 9-pin mini-style connector
Manifold mounting
Housing type HDLS Plug-in, HDLS Non-Plug-in
Sealing IP65/66/67; NEMA 1, 3, 4, 4X, 6, 6P, 12, 13
-12C to 121C [10F to 250F];
Operating temperature
optional: -40C to 121C [-40F to 250 F]
Agency approvals and stan-
UL, CE, CSA, CCC
dards
UNSPSC code 302119
UNSPSC commodity 302119 Switches and controls and relays
Switch Type Heads Body/Basic Switch Codes Modification Codes Wobble Actuator
HDLS Series Side rotary, Side rotary, Plug-in Plug-in Non-plug-in 4-pin 5-conductor Wobble,
A momentary L sequential A mini-style PA STOOW-A cable, 7A plastic
Heavy-Duty Single Pole Double Pole Double Pole 8 ft
Limit Switch Top rotary, Side rotary,
1A Standard
2B Standard
4L Standard
B
5-pin
XA
9-conductor
7M Wobble,
B momentary M center neutral switch switch switch mini-style
STOOW-A cable,
8 ft wire
Top roller Side rotary, Gold contacts, Center Center 4-conductor Clockwise Cat whisker,
* 3 or 4 after D plunger P momentary,
low pretravel
1G manifold mount 2D neutral 4N neutral E SJTOW-A cable,
6 ft
1 head rotation 8A 5.5 in steel
the LS
Side rotary, Low 120 V neon Standard switch 8-pin Counterclockwise Cat whisker,
indicates
E
Side plunger
plain, momentary R momentary, 1H force 2R indicator 4S golf contacts J mini-style 2 head rotation 8B 7.5 in steel
special metric low torque
conduit Side plunger Side rotary, 120 V neon Standard switch Sequential, 9-conductor Head assembled Coil spring,
threads:
F roller, momentary S gravity return
extr. low torque
5A indicator 2S golf contacts 4T gold contacts M STOOW-A cable,
6 ft
3 with actuator to
right side
8C 5.5 in
3 = PG 13,5 Side plunger Side rotary, 240 V neon Sequential, Center neutral, 5-conductor Head assembled Cat whisker,
4 = 20 mm G plain, maintained T momentary, 8A indicator 2T gold contacts 4U gold contacts P STOOW-A cable, 4 with actuator to
left side
8D plastic
extr. low torque 12 ft
Side rotary, Side rotary, 24 V LED Center neutral, Standard Head assembled
9-pin
H momentary, low
pretravel & torque
U momentary,
5 max. pretravel
9A indicator 2U gold contacts 7L switch,
1/2 in conduit
R mini-style 5 with actuator to
mounting surface
Standard 5-pin Roller
J
Wobble
stick V
Top plunger,
adjustable
Non-plug-in 6B switch,
1/2 in conduit
7M Sequential,
1/2 in conduit S micro-style 6 perpendicular to
mounting surface
Single Pole
Cat Side plunger, Sequential, Center neutral, 9-conductor Indicator light
K whisker W momentary,
adjustable
3K Standard
switch 6C 1/2 in conduit 7N 1/2 in conduit X STOOW-A cable,
12 ft
7 wired to normally
closed circuit
Center neutral, Stnd. switch, 3-foot mini-style Roller on side
6D 1/2 in conduit 7S gold contacts,
1/2 in conduit BB pigtail,
single pole
8 plunger in
vertical position
120 V neon Sequential, 4-pin micro-style
NOTE: Not all combinations of model codes 6R indicator,
1/2 in conduit
7T gold contacts,
1/2 in conduit
DD with jumper
are available. Please contact your local
Stnd. switch, Center neutral,
Honeywell provider for assistance. 6S gold contacts,
1/2 in conduit
7U gold contacts,
1/2 in conduit
Sequential,
6T gold contacts,
1/2 in conduit
Center neutral,
6U gold contacts,
1/2 in conduit
4 sensing.honeywell.com
MICRO SWITCH Heavy-Duty Limit Switch, HDLS Series
ASSEMBLY MODIFICATIONS ROTARY HDLS Series Electrical Ratings:
10 A Continuous Carry
Momentary action rotary switches can be furnished in other
ac Volts; Pilot Duty: AC15, A600/B600
than the normal assembled conditions. To specify modifica-
tions, add the numbers shown below to the catalog listings. Electrical Circuitry Vac Amps at 0.35 Amps at 0.35
Modification number suffixes are: Rating Power Factor Power Factor
1 Clockwise actuation only Make Break
2 Counterclockwise actuation only A* SPDT 120 60 6
3 Shaft to right of switch front AC15, DPDT 240 30 3
A600
4 Shaft to left of switch front 480 15 1.5
5 Shaft to back of switch 600 12 1.2
7 Indicator light wired to NC circuit
B D 120 30 3
AC15, 240 15 1.5
For example, B600
Catalog listing LSA1A23 is an LSA1A switch adjusted for coun- 480 7.5 0.75
terclockwise actuation only. The operating shaft is to the right 600 6 0.60
side of the switch when viewing it from the front (label side). D Gravity return (Model LSS..) and extra-low torque (Model
No lever. LST..)
Catalog listing LSA8A7 is an LSA8A switch with the 240 volt
indicator light wired to the NC circuit. No lever. HDLS Series Electrical Ratings:
dc Volts; Pilot Duty: DC13, R300
Electrical Circuitry Vdc Make & Break Make & Break
PLUNGER ASSEMBLY MODIFICATIONS Rating Amps Amps
Inductive Resistive
Add the following modification numbers to the catalog listing
in the plunger switch: A, B* SPDT 120 0.25 0.8
DPDT 240 0.15 0.4
3 Side plunger to right of switch front
4 Side plunger to left of switch front
* For switches with an indicator light, use only at voltage stated
5 Side plunger to back of switch
for indicator light.
6 Roller on top plungers perpendicular to mounting sur-
face
MICRO SWITCH HDLS limit switches are capable of the follow-
7 Light on indicator versions wired to NC circuit
ing low voltage dc loads
8 Roller on side plungers in vertical position
For example, Circuitry Vdc Amps Amps
Catalog listing LSF1A3 is an LSF1A switch with the side roller Inductive Resistive
plunger to the right side. SPDT 24 10 10
DPDT 24 10 10
6 sensing.honeywell.com
MICRO SWITCH Heavy-Duty Limit Switch, HDLS Series
LSE - Side pin plunger: For actuating LSW - Adjustable side pin plunger:
motion inline with the plunger travel. Ac- Has the same features of the side plain
tuating head may be faced in any of four plunger plus the means to adjust the
positions, 90 apart. A boot seal on the operating points of the switch from
plunger and a seal between the head 41 mm to 47,4 mm [1.615 in to 1.865
and housing keep out coolant, dust, and in]. Seals are same as side pin plunger.
chips. Momentary action. Momentary action.
LSF - Side roller plunger: Fits close LSG - Maintained contact side pin
quarters under cams and slides. The plunger: Offers a maintained contact
head may be faced in any of four posi- on actuation of the switch. A reverse
tions, 90 apart. The roller can be turned motion of the plunger resets the
vertical or horizontal to the switch. Seals switch. Sealing is the same as other
are same as side pin plunger. Momen- side plunger actuation heads. Operat-
tary action. ing temperature range is -1C to 93C
[30F to 200F].
WOBBLE LEVER ACTUATING HEADS: Heads come with either a spring wire, Delrin plastic rod, or steel cat whisker. Any move-
ment of the lever (except pull) will actuate the switch. Standard temperature range of -12C to 93C [10F to 200F].
LSJ1A-7M - Spring LSJ1A-7N - Flexible LSK1A-8C - Coil LSJ1A-7A - Plastic LSK1A-8A - Cat
wire: 300 Series SST actuator: Designed spring: Designed with rod: Recommended whisker: 300 Series
wire may be formed for with a tin-plated cable. a 300 Series SST coil where possible scratch- SST actuator designed
special applications. spring. ing or marring by for low operating force
the actuator is to be applications.
avoided.
Table 2. Temperature Limits Standard HDLS Low Temperature HDLS High Temperature HDLS
(Fluorosilicone Sealed): Y_B (Fluorocarbon Sealed)*: Y_C
Low Limit High Limit Low Limit High Limit Low Limit High
Limit
-12C -1C 93C 121C -40C -29C 93C 121C -12C -1C 121C
[10F] [30F] [200F] [250F] [-40F] [-20F] [200F] [250F] [10F] [30F] [250F]
LSA - Side Rotary Momentary X X X X X X
LSB - Top Rotary X X X X X X
LSC - Top Plain Plunger X X X X X X
LSD - Top Roller Plunger X X X X X X
LSE - Side Plain Plunger X X X X X X
LSF - Side Roller Plunger X X X X X X
LSG - Side Plunger, Maintained X X X X X X
LSH - Side Rotary, Low PT, Low Torque X X X X X X
LSJ - Wobble Stick X X X X X X
LSK - Cat Whisker X X X X X X
LSL - Side Rotary, Sequence X X X X X X
LSM - Side Rotary, Center Neutral X X X X X X
LSN - Side Rotary, Maintained X X X X X X
LSP - Side Rotary, Low Pretravel X X X X X X
LSR - Side Rotary, Low Torque X X X X X X
LSU - 5 Low Pretravel X X X X X X
LSV - Top Adjustable Plunger X X X X X X
LSW - Side Adjustable Plunger X X X X X X
* For HDLS application wherein the upper temperature limit is normally above 93C [200F], much longer switch life can be obtained by using
completely fluorocarbon-sealed switches rather than standard HDLS.
8 sensing.honeywell.com
MICRO SWITCH Heavy-Duty Limit Switch, HDLS Series
2 1 5 6
Wiring Diagram (Style DD)
4 7 = Ground
2 1
3 4
1 2
Pin 3 not connected
Table 3. Side Rotary MICRO SWITCH HDLS Series Order Guide/Recommended Listings
3 4 3 4 3 4 3 4 3 4
3 4
1 2 1 2 1 2 1 2 1 2
1 2
7
1-2
3-4
3-4
1-2
7 8 7 8 8
1-2
3-4
3-4
1-2
1-2
3-4
3-4
1-2
0 5 6 5 6 0 2 5 6
0 5
1-2/5-6
3-4/7-8
3-4/7-8
1-2/5-6
1-2/5-6
3-4/7-8
3-4/7-8
1-2/5-6
1-2/5-6
3-4/7-8
3-4/7-8
1-2/5-6
10 6
15 9
0 0 0 1
5 5
8 9
15
75
75
75
Contact closed n 75
75 75
Contact open o
Non-plug-
Silver 0.5 in LSA3K LSP3K LSU3K
in
Silver Plug-in 0.75 in LSA2B LSP2B LSU2B
Gold 4
Plug-in 0.75 in LSA2S
Silver Plug-in 0.5 in LSA6B LSP6B LSU6B
Gold4 Plug-in 0.5 in LSA6S
DPDT
10 sensing.honeywell.com
MICRO SWITCH Heavy-Duty Limit Switch, HDLS Series
Table 4. Side Rotary MICRO SWITCH HDLS Series Order Guide/Recommended Listings
1-2
3-4
3-4
1-2
7
1-2
3-4
3-4
1-2
7 8 8
0 5 0 5 6
6
6
1-2/5-6
3-4/7-8
3-4/7-8
1-2/5-6
1-2/5-6
3-4/7-8
3-4/7-8
1-2/5-6
10 9
15
0 0
5
8 9
15
75 75
Contact closed n 75 75
Contact open o
Pretravel 15 max. 15 max. 9 max. 9 max.
Different. travel 5 max. 7 max. 3 max. 4 max.
Overtravel 60 min. 60 min. 66 min. 66 min.
Oper. torque 0,19 Nm [1.7 in-lb] max. 0,19 Nm [1.7 in-lb] max.
Action CW & CCW (Momentary)
Op. temp range3 -1C to 121C [30F to 250F] (for low temp, high temp, or preleaded versions, see pages 8-9)
Circuitry Contacts Body Style2
Conduit Options
(NPT)
Silver Plug-in 0.5 in LSR1A LSH1A
Gold4 Plug-in 0.5 in LSR1E LSH1E
Silver Plug-in 0.5 in 120 V Ind. lite1
LSR5A LSH5A
SPDT
Table 5. Side Rotary MICRO SWITCH HDLS Series Order Guide/Recommended Listings
1-2
3-4
5-6
7-8
7-8
5-6
3-4
1-2
1
1 2
Maintained
Contact 7
2
8 75
0
0
1-2
3-4
3 4 5 6 10
15
0 1 2 8
1-2/5-6
3-4/7-8
3-4/7-8
1-2/5-6
20
25
18
1-2
3-4
3-4
1-2
0 0
90
25 25
18
180
8
270 65 65 0 75 75
1-2
3-4
3-4
1-2
5-6
7-8
7-8
5-6
Contact closed n
Contact open o 0 85 85
Pole 1: 15
Pretravel 65 max. 65 max. 18 max.
Pole 2: addl 10
Different. travel 40 max. 40 max. 10 max. each pole: 5
Overtravel 20 min. 20 min. 57 min. 48 min.
Oper. torque 0,45 Nm [4 in-lb] 0,45 Nm [4 in-lb] 0,45 Nm [4 in-lb]
Action Maintained CW & CCW (Momentary)
-12C to 121C
-1C to 121C [30F to 250F] [10F to 250F]
Op. temp range6 (for low temp, high temp, or preleaded versions, see pages 8-9) (for low temp, high temp, or pre-
leaded versions, see pages 8-9)
12 sensing.honeywell.com
MICRO SWITCH Heavy-Duty Limit Switch, HDLS Series
Figure 2. MICRO SWITCH HDLS side rotary (single pole) di- Figure 3. MICRO SWITCH HDLS side rotary (double pole)
mensions dimensions
7,32 7,32
[.29] [.29]
106,7
[4.20]
59,4 119
[2.34] 70,4 [4.69] 59,4
[2.77] [2.34]
82,6
74,9 89,5 [3.53]
[2.95] [3.53]
119
[4.69] 59,4
59,5 [2.34]
[2.34] 70,4 82,6
[2.77] 89,7 [3.25]
75,9 [3.53]
[2.97]
20,3 21,3
[0.8] 29,4 [.84]
29,4
CONDUIT OPENING [1.16] [1.16]
LOCATION 41,1 CONDUIT OPENING 38,1
36,6 [1.62] LOCATION [1.50] 47,8
[1.44] 45,3 [1.88]
2X 10-32 UNF [1.78]
44,5 TAPPED FROM REAR ONLY 2X 10-32 UNF
[1.75] TAPPED FROM REAR ONLY
2X 5,2 [.20] MTG HOLES
2X 5,2 [.20] MTG HOLES
8,0 [.32] C'BORE X 7,8 [.31] DEPTH
1-2
3-4
3-4
1-2
0 5 6
15
1-2/5-6
3-4/7-8
3-4/7-8
1-2/5-6
25
0
13
25
135
Contact closed n 135
Contact open o
Pretravel 25 max. 25 max.
Different. travel 10 max. 12 max.
Overtravel 110 min. 110 min.
Oper. torque 0,28 Nm [2.5 in lb] max.
Action CW and CCW (Momentary)
Op. temp range3 -12C to 121C [10F to 250F] (for low temp, high temp, or preleaded versions, see pages 8-9)
Circuitry Contacts Body Style2 Conduit Options
(NPT)
Silver Plug-in 0.5 in LSB1A
Gold 4
Plug-in 0.5 in LSB1E
Silver Plug-in 0.5 in 120 V Ind. lite1 LSB5A
SPDT
14 sensing.honeywell.com
MICRO SWITCH Heavy-Duty Limit Switch, HDLS Series
Figure 4. MICRO SWITCH HDLS top rotary (single pole) dimen- Figure 5. MICRO SWITCH HDLS top rotary (double pole)
sions dimensions
57,2
[2.25]
127.6 57,2
[5.02] 36,4 42,4 [2.25]
36,4 42,4
[1.43] [1.67] [1.43] [1.67]
139,8
[5.5]
59,4 59,5
[2.34] 70,4 89.7 [2.34]
74,9 82,6
[2.95] [2.77] [3.53] [3.25]
16,5 29,4
[.65] [1.16] 18,8 29,4
25,4 [.74] [1.16]
[1.00] 41,1 26,4
39,1 [1.62] [1.04] 47,8
[1.54] 44,4 [1.88]
[1.75] 2X 5,2 [.20] MTG HOLES 45,3
CONDUIT OPENING [1.78] 2X 10-32 UNF
LOCATION CONDUIT OPENING TAPPED FROM REAR ONLY
2X 10-32 UNF LOCATION
TAPPED FROM REAR ONLY 2X 5,2 [.20] MTG HOLES
8,0 [.32] C'BORE X 7,8 [.31] DEPTH
21,6 21.6
[.85] 39,6 [.85] 39.8
[1.56] [1.56]
MTG PADS 7,32 DIA
MTG PADS 7,4 DIA [.29]
[.29]
57,2
[2.25]
36,4 36,4 42,4 36,4
42,4 [1.43]
[1.43] [1.67] [1.43] [1.67]
127,6 139.8
[5.02] [5.5]
59,5
75,8 59,4 [2.34]
[2.34] 70,4 89.7
[2.98] [3.53] 82.6
[2.77] [3.25]
20,3 29,4
[.80] [1.16] 21,3
[.84] 29,4
36,6 41,1 38,1 [1.16]
[1.44] [1.62] [1.50]
39,0
[1.54] 47.8
44,4 2X 5,2 [.20] MTG HOLES CONDUIT OPENING 45,3 [1.88]
[1.75] LOCATION [1.78]
CONDUIT OPENING 2X 10-32 UNF
LOCATION 2X 10-32 UNF TAPPED FROM REAR ONLY
TAPPED FROM REAR ONLY
2X 5,2 [.20] MTG HOLES
8,0 [.32] C'BORE X 7,8 [.31] DEPTH
Table 7. Common levers for use with MICRO SWITCH HDLS Rotary Switches
Levers for use with side or top rotary actuated switches are available in a wide choice of sizes and materials. The most common
listings are shown below. Rollers may be on either side of the lever to best match the external acutating mechanism.
LSZ55A,LSZ55B,
LSZ60 LSZ53A, LSZ53B, LSZ53D LSZ54R
LSZ55C,LSZ55D
one-way yoke lever, nylon and steel rollers, spring wire
offset lever,
roller lever front/back placement 305 mm [12 in]
front/back
16 sensing.honeywell.com
MICRO SWITCH Heavy-Duty Limit Switch, HDLS Series
Catalog Material Rod/Roller Rod/Roller Roller Catalog Material Rod/Roller Rod/Roller Roller
Listing Dia. mm Width mm Mounting Listing Dia. mm Width mm Mounting
[in] [in] [in] [in]
Fixed 38,1 mm [1.5 in] radius Fixed 38,1 mm [1.5 in] radius
Rollerless n/a n/a n/a Rollerless n/a n/a n/a
LSZ51A Nylon 19 [0.75] 6,35 [0.25] Front LSZ55A Nylon 19 [0.75] 6,35 [0.25] Back
LSZ51B Steel 19 [0.75] 6,35 [0.25] Front LSZ55B Steel 19 [0.75] 6,35 [0.25] Back
LSZ51C Nylon 19 [0.75] 6,35 [0.25] Back LSZ55C Nylon 19 [0.75] 6,35 [0.25] Front
LSZ51D Steel 19 [0.75] 6,35 [0.25] Back LSZ55D Steel 19 [0.75] 6,35 [0.25] Front
LSZ51F Nylon 25,4 [1.0] 12,7 [0.50] Front LSZ55E Nylon 19 [0.75] 12,7 [0.50] Front
LSZ51G Nylon 38,1 [1.5] 6,35 [0.25] Front LSZ55K Nylon 38,1 [1.5] 6,35 [0.25] Front
LSZ51J Nylon 25,4 [1.0] 12,7 [0.50] Back Short fixed - 33 mm [1.3 in] radius
LSZ51L Ball bearing 19 [0.75] 6,35 [0.25] Back LSZ59A Nylon 19 [0.75] 6,35 [0.25] Front
LSZ51M Nylon 19 [0.75] 31,7 [1.25] Back LSZ59B Steel 19 [0.75] 6,35 [0.25] Front
LSZ51N Steel 19 [0.75] 31,7 [1.25] Front LSZ59C Nylon 19 [0.75] 6,35 [0.25] Back
LSZ51P Nylon 19 [0.75] 12,7 [0.50] Front LSZ59D Steel 19 [0.75] 6,35 [0.25] Back
Adjustable 38,1 mm to 89,0 mm [1.5 in to 3.5 in] radius
Rollerless n/a n/a n/a
LSZ52A Nylon 19 [0.75] 6,35 [0.25] Back
38,1 mm [1.5 in] radius one-way roller lever
LSZ52B Steel 19 [0.75] 6,35 [0.25] Back
LSZ60A Nylon 19 [0.75] 6,35 [0.25] Front
LSZ52C Nylon 19 [0.75] 6,35 [0.25] Front
LSZ60B Steel 19 [0.75] 6,35 [0.25] Front
LSZ52D Steel 19 [0.75] 6,35 [0.25] Front
LSZ52E Nylon 19 [0.75] 33,0 [1.30] Front
LSZ52J Nylon 25,4 [1.0] 12,7 [0.50] Front
LSZ52K Nylon 38,1 [1.5] 6,35 [0.25] Front
LSZ52L Ball bearing 19 [0.75] 6,35 [0.25] Front Flexible loop
LSZ52M Nylon 50,8 [2.0] 6,35 [0.25] Front LSZ61 4,8 [ 0.19] 152 mm [6 in] flexible loop
LSZ52N Nylon 19 [0.75] 12,7 [0.50] Front Plastic
Yoke 38,1 mm [1.5 in] radius LSZ618 4,8 [ 0.19] 241 mm [9.5 in] flexible loop
Plastic
LSZ53A Nylon 19 [0.75] 6,35 [0.25] Front/Back
LSZ54 Hub only n/a n/a n/a
LSZ53B Steel 19 [0.75] 6,35 [0.25] Front/Back
LSZ53D Steel 19 [0.75] 6,35 [0.25] Front/Front
LSZ53E Nylon 19 [0.75] 6,35 [0.25] Back/Front
LSZ53M Nylon 19 [0.75] 31,7 [1.25] Back/Front
LSZ53P Steel 19 [0.75] 6,35 [0.25] Back/Back
LSZ53S Nylon 19 [0.75] 6,35 [0.25] Back/Back Spring rod
Rod LSZ68 Delrin rod, 305 6,35 n/a n/a
Hub only n/a n/a n/a [12 ] [ 0.25]
LSZ617 Delrin rod, 406 6,35 n/a n/a
LSZ54M Alum, 140 mm 3,2 n/a n/a [16] [ 0.25]
[5.5 in] [ 0.125] LSZ686 Delrin rod, 6,35 n/a n/a
152 [6] [ 0.25]
LSZ54N Stainless, 330 3,2 n/a n/a
mm [13 in] [ 0.125]
LSZ54R SST spring 1,9 n/a n/a
wire, 305 mm [ 0.075]
[12 in]
LSZ54V Flex cable (tin 4,8 n/a n/a
plated steel), [ 0.19] Rubber roller levers
122 mm
[4.8 in] LSZ51Y Rubber 50 [2.0] 12,7 front
38,1 mm [1.5 in] [0.50]
LSZ54P Plastic rod, 6,85 n/a n/a radius (std.)
533,4 mm [ 0.27]
[21 in] LSZ55Y Rubber 50 [2.0] 12,7 front
38,1 mm [1.5 in] [0.50]
LSZ54W Plastic rod, 6,85 n/a n/a radius (offset)
183 mm [ 0.27]
[7.2 in] LSZ52Y Rubber 50 [2.0] 12,7 front
38,1 mm to 89,0 [0.50]
LSZ54T 330 [13] 4,8 n/a n/a mm [1.5 in to
stainless steel [ 0.19] 3.5 in] radius
Spoke (adjustable)
LSZ69CA 152 mm [6.0 3,2 [0.125] n/a n/a Plastic roller levers
in] Stainless LSZ67AA* Plastic 38,1 [1.5] 96,5 [3.8] n/a
(conveyor)
* may require orientation of switch and lever to enable gravity to help restore free position of switch.
Figure 6. LSZ51 type levers cam tracking Figure 7. LSZ52 type levers cam tracking
57,4 - 63,8 6,35 mm x 19,0 mm dia
[2.26 - 2.51] 56,4 mm to 62,7 mm
ADJUSTMENT [2.22 in to 2.47 in] [0.25 in x 0.75 in dia] OR
LEVER INVERTED 58,9 - 65,3 adjustment 6,35 mm x 38,1 mm dia
51,0 - 57,4 [2.32 - 2.57]
[2.01 - 2.26] ADJUSTMENT [0.25 in x 1.5 in dia] OR
ADJUSTMENT 42,9 - 49.3 12,7 mm x 25,4 mm dia
[1.69 - 1.94]
6,35 X 19,0 DIA ADJUSTMENT [0.50 in x 1.0 in dia]
[.25 X .75 DIA]
LEVER 6,35 X 19,0 DIA
INVERTED [.25 X .75 DIA]
21,3
[.85]
21,3 mm
21,3 [0.85 in]
38,1 [.85]
[1.5]
38,1 mm to 91,1 mm
38,1
[1.50] [1.5 in to 3.6 in]
25,4 adjustment
[1.00] 25,4
[1.00]
19,0
[.75] 25,4 mm
19,05
[.75]
[1.00 in]
19,0 mm
11,0 [0.75 in]
[.43] 6,35
[.25] 11,0 6,35
ADJUSTMENT [.43] [.25]
ADJUSTMENT
6,35 mm
11,0 mm [0.25 in]
[0.43 in] adjustment
Figure 8. LSZ54 type levers cam tracking Figure 9. LSZ55 type levers cam tracking
78,2 mm to 84,6 mm
58,7 mm to 65,0 mm [3.08 in to 3.33 in]
[2.31 in to 2.56 in] adjustment
adjustment
70,9 mm to 77,2 mm 6,35 mm x 19,0 mm dia.
[2.79 in to 3.04 in] [0.25 in x 0.75 in dia.]
adjustment
21,3 mm
21,3 mm [0.85 in]
127,0 mm [5.0 in] max. aluminum rod
[0.85 in]
330,2 mm [13.0 in] max. stainless steel rod
38,1 mm
[1.50 in]
25,4 mm
25,4 mm
[1.00 in]
[1.0 in]
19,05 mm
9,05 mm [0.75 in]
[0.75 in]
18 sensing.honeywell.com
MICRO SWITCH Heavy-Duty Limit Switch, HDLS Series
Table 9. Top Plungers MICRO SWITCH HDLS Series Order Guide/Recommended Listings
1-2
3-4
3-4
1-2
1-2
3-4
3-4
1-2
1-2
3-4
3-4
1-2
1-2/5-6
3-4/7-8
3-4/7-8
1-2/5-6
1-2/5-6
3-4/7-8
3-4/7-8
1-2/5-6
0 in 0 in 0 in
1-2/5-6
3-4/7-8
3-4/7-8
1-2/5-6
0 in 0 in
1,4 mm 0 in
1,78 mm 1,4 mm 1,4 mm
[0.055 in] 1,78 mm
[0.07 in] 1,27 mm 1,78 mm [0.055 in]
1,27 mm
[0.055 in] 1,27 mm
[0.050 in] [0.07 in] [0.07 in]
1,4 mm [0.050 in] 1,4 mm [0.050 in]
1,4 mm
[0.07 in] [0.07 in] [0.07 in]
6,6 mm
[0.26 in] 6,6 mm 6,6 mm
[0.26 in] [0.26 in]
6,6 mm 6,6 mm
[0.26 in]
6,6 mm
[0.26 in]
[0.26 in]
Contact closed n
Contact open o
Non-plug-
Silver 0.75 in LSC4L LSD4L LSV4L
in
DPDT
Double Break
Non-plug-
Silver 0.5 in LSC7L LSD7L LSV7L
in
1
Use at voltage indicated for light. Wired to NO circuit. Upper temperature limit for lighted units is 93C [200F]
2
Plug-in listings include base receptacle
3
Completely fluorocarbon sealed switches are preferred for use in temperatures above 93C [200F]
4
Gold-plated contacts
NOTE: Same polarity each pole.
To order a fluorocarbon sealed switch, insert the letters Y and C into the catalog listing as follows. The LSA1A limit switch is changed to a LSYAC1A limit switch.
To order a low temperature, fluorosilicone sealed switch, insert the letters Y and B into the catalog listing as follows. The LSA1A limit switch is changed to a LSYAB1A
limit switch.
46,0 46,0
MTG PADS [1.81] [1.81]
OPERATING POINT 28,7 MTG PADS OPERATING POINT 28,7
[1.13] [1.13]
59,4 59,5
[2.34] 70,4 [2.34]
[2.77] 82,6
74,9 [3.25]
[2.95] 89,7
[3.53]
46,0
46,0 [1.84]
MTG PADS [1.81] MTG PADS OPERATING POINT
28,7 28,7
OPERATING POINT
[1.13] [1.13]
59,5
89,7 [2.34]
59,4 82,6
70,4 [3.53]
[2.34] [3.25]
[2.77]
75,8
[2.98]
29,4
[1.16]
29,4
CONDUIT OPENING [1.16] 47,8
CONDUIT OPENING
LOCATION LOCATION 21,3 [1.88]
41,1
20,3 [0.84]
[1.62]
[.80] 38,1
2X 10-32 UNF
[1.50]
36,6 2X 10-32 UNF TAPPED FROM REAR ONLY
45,3
[1.44] TAPPED FROM REAR ONLY [1.78] 2X 5,2 [.20] MTG HOLES
39,0 8,0 [.32] C'BORE X 7,8 [.31] DEPTH
[1.54] 2X 5,2 [.20] MTG HOLES
44,4
[1.75]
20 sensing.honeywell.com
MICRO SWITCH Heavy-Duty Limit Switch, HDLS Series
Figure 12. MICRO SWITCH HDLS LSD Series (single pole) top Figure 13. MICRO SWITCH HDLS LSD Series (double pole) top
roller plunger dimensions roller plunger dimensions
55,9 55,9
[2.20] [2,20]
OPERATING OPERATING
28,7 POINT POINT
28,7
[1.13] [1.13]
74,9 59,4
[2.95] [2.34] 70,4 59,5
[2.77] 89,7 [2.34]
82,6
[3.53]
[3.25]
CONDUIT OPENING
LOCATION 29,4
16,5 [1.16] CONDUIT OPENING
[.65] LOCATION
41,1 29,4
25,4 [1.62] 21,3 [1.16]
[1.00] [.84] 47,8
39,1 2X 5,2 [.20] MTG HOLES 26,4 [1.88]
[1.54] [1.04] 2X 10-32 UNF
2X 10-32 UNF 45,3
44,4 TAPPED FROM REAR ONLY [1.78] TAPPED FROM REAR ONLY
[1.54]
2X 5,2 [.20] MTG HOLES
9,5 [.37] C'BORE X 7,8 [.31] DEPTH
DIMS: MM
[IN]
LSD SPDT PLUG-IN PRODUCT DIMENSIONS
39,6 39,6
[1.56] [1.56]
21,6
25,4 [.85] 25,4
21,6 [1.00] [1.00]
4,8 14,7
[.85] MTG PADS [0.19]
14,7 12,7 [.58]
4,8 [.58] [.50]
12,7
[1.19] [.50]
55,9
[2.20]
55,9 OPERATING
MTG PADS [2.20] POINT
28,7
OPERATING
POINT [1.13]
28,7
[1.13]
59,5
89,7 [2.34]
[3.53] 82,6
75,8 59,4 [3.25]
[2.34] 70,4
[2.98] [2.77]
59,5
[2.34]
89,7 82,6
59,4 [3.53] [3.25]
[2.34] 70,4
[2.77]
74,9
[2.95]
CONDUIT OPENING
LOCATION 29,4
CONDUIT OPENING 29,4 [1.16]
LOCATION [1.16] 18.8 47,8
41,1 [.74] [1.88]
16,5 26,4
[.65] [1.62]
[1.04] 2X 10-32 UNF
25,4 38,1 TAPPED FROM REAR ONLY
[1.00] [1.50]
39,0 2X 5,2 [.20] MTG HOLES 45,3 2X 5,2 [.20] MTG HOLES
[1.54] [1.78] 9,5 [.37] C'BORE X 7,8 [.31] DEPTH
44,5 2X 10-32 UNF
[1.75] TAPPED FROM REAR ONLY DIMS: MM
[IN]
DIMS: MM
[IN] LSV DPDT PLUG-IN PRODUCT DIMENSIONS
(FOR REFERENCE ONLY)
LSV
SPDT SPDT PLUG-IN(mm[in])
Non-plug-in PRODUCT DIMENSIONS DPDT Non-plug-in (mm[in])
(FOR REFERENCE ONLY)
14,7
14,7
25,4 [.58]
[.58]
21,6 7,9 [1.00]
7,9
[.85] [.31] 21,6
[.31]
36,6 [.85]
25,4 [1.56]
[1.00] 17,5 28,7 59,4
MTG PADS [.69] [1.13]
17,5 59,4 [2.34]
28,7 [2.34] 53,1 MAX OPERATING
[.69] [1.13] POINT
MTG PADS 53,1 MAX OPERATING [2.09]
POINT MIN OPERATING
[2.09] POINT
MIN OPERATING
POINT
59,5
89.65 [2.34]
82,6
59,4 [3.25]
75,8 70,4
[2.98] [2.34]
[2.77]
CONDUIT OPENING
LOCATION 29,4
CONDUIT OPENING 29,4 [1.16]
LOCATION [1.16] 21,3
[.84]
47,8
20,3 41,1 38,1
[1.88]
[.80] [1.62] [1.50]
45,3 2X 10-32 UNF
36,6 [1.78] TAPPED FROM REAR ONLY
[1.44] 2X 5,2 [.20] MTG HOLES
39,0 2X 5,2 [.20] MTG HOLES
[1.54] 2X 10-32 UNF 8,0 [.32] C'BORE X 7,8 [.31] DEPTH
44,4 DIMS: MM
[1.75] TAPPED FROM REAR ONLY [IN]
DIMS: MM
[IN] LSV DPDT NON PLUG-IN PRODUCT DIMENSIONS
(FOR REFERENCE ONLY)
22 sensing.honeywell.com
MICRO SWITCH Heavy-Duty Limit Switch, HDLS Series
Table 10. Side Plungers MICRO SWITCH HDLS Series Order Guide/Recommended Listings
Heads may be positioned to accept actuation Plain (LSE) Roller (LSF) Adjustable Maintained (LSG)
(LSW)
from any of four directions, 90 apart.
Snap Action
2NO/2NC
Snap Action
1NO/1NC 3 4
1 2
1-2/5-6
3-4/7-8
3-4/7-8
1-2/5-6
3 4
7 8
1-2
3-4
3-4
1-2
1 2 0 in 0 in
5 6
1-2/5-6
3-4/7-8
3-4/7-8
1-2/5-6
1-2
3-4
3-4
1-2
0 in
2,03 mm 2,03 mm
[0.08 in] [0.08 in]
0 in reset reset
1,4 mm
2,54 mm [0.055 in] 1,4 mm
[0.10 in] 2,54 mm [0.055 in] 4,32 mm 4,32 mm
[0.10 in] [0.17 in] [0.17 in]
trip trip
6,35 mm 6,35 mm
[0.25 in] [0.25 in]
7,36 mm 7,36 mm
Contact closed n [0.29 in]
[0.29 in]
Contact open o
DIMS: MM
[IN] LSE DPDT PLUG-IN PRODUCT DIMENSIONS
33,0 14,7
[1.30] [.58] MTG PADS 33,0 14,7
21,6
21,6 OPERATING [1.30] [.58]
[.85]
MTG PADS [.85] POINT OPERATING
39,6 POINT 39,6
[1.56] [1.56]
59,4 59,5
75,8 70,4
[2.34] 89,7 [2.34]
[2.98] [2.77] 82,6
[3.53]
[3.25]
CONDUIT OPENING
LOCATION 29,4
[1.16] CONDUIT OPENING 29,4
20,3 LOCATION [1.16]
[.80] 41,1 47,8
36,6 [1.62] 21,3
[1.88]
[1.44] [.84]
2X 5,2 [.20] MTG HOLES
38,1
39,0 [1.50]
[1.54] 2X 10-32 UNF
44,4 2X 10-32 UNF TAPPED FROM REAR ONLY
TAPPED FROM REAR ONLY 45,3
[1.75] [1.78]
2X 5,2 [.20] MTG HOLES
8,0 [.32] C'BORE X 7,8 [.31] DEPTH
24 sensing.honeywell.com
MICRO SWITCH Heavy-Duty Limit Switch, HDLS Series
Figure 18. MICRO SWITCH HDLS LSF Series side roller plunger Figure 19. MICRO SWITCH HDLS LSF Series side roller plunger
(single pole) dimensions (double pole) dimensions
59,5
74,9 59,4 89,7 [2.34]
[2.95] [2.34] 70,4 82,6
[3,53]
[2.77] [3.25]
CONDUIT OPENING
CONDUIT OPENING 29,4 LOCATION 29,4
LOCATION [1.16] [1.16]
16,5
[.65] 41,1 47,8
[1,62] 18,8 [1.88]
25,4 [.74]
[1.00] 26,4 2X 10-32 UNF
39,1 2X 5,2 [.20] MTG HOLES [1.04] TAPPED FROM REAR ONLY
38,1
[1.54] [1.50]
44,4 2X 10-32 UNF 2X 5,2 [.20] MTG HOLES
TAPPED FROM REAR ONLY 45,3 9,5 [.37] C'BORE X 7,8 [.31] DEPTH
[1.54]
[1.78]
DIMS: MM
[IN]
LSF
SPDT SPDT PLUG-IN
Non-plug-in PRODUCT DIMENSIONS
(mm[in]) LSF DPDT
DPDT PLUG-IN PRODUCT
Non-plug-in (mm[in])DIMENSIONS
(FOR REFERENCE ONLY) (FOR REFERENCE ONLY)
44,2 44,2
[1.74] 14,7 [1.74]
OPERATING [.58] OPERATING
21,6 POINT POINT
[.85] 39,6 MTG PADS
MTG PADS 12,7 [1.56] 14,7
[.50] 21,6 [.58]
ROLLER 4,8 12,7
[.85]
DIAMETER [.19] [.50] 39,6
ROLLER DIAMETER [1.56]
20,3
[.80] 19,0 31,5 4,8
[1.24] 20,3 [.19]
[.75] [.80]
19,0 31,5
25,4 [.75] [1.24]
[1.00] n 25,4
[1.00]
CONDUIT OPENING
LOCATION 29,4
[1.16]
20,3
[.80] 41,1 CONDUIT OPENING
[1,62] LOCATION 29,4
36,6 [1.16]
[1.44] 2X 5,2 [.20] MTG HOLES 21,3
39,0 [.84] 47,8
[1.54] [1.88]
2X 10-32 UNF 38,1
44,4 [1.50]
[1.75] TAPPED FROM REAR ONLY 45,3 2X 10-32 UNF
[1.78] TAPPED FROM REAR ONLY
Figure 20. MICRO SWITCH HDLS LSW Series side adjustable Figure 21. MICRO SWITCH HDLS LSW Series side adjustable
plunger (single pole) dimensions plunger (double pole) dimensions
25,4
25,4
[1.00]
[1.00]
7,9
[.31]
7,9 ACROSS
74,9 59,4 59,4
[.31] FLATS
[2.34] 70,4 89,7 [2.34]
[2.95] ACROSS 82,6
FLATS [2.77] [3.53]
[3.25]
29,4
CONDUIT OPENING [1.16]
LOCATION CONDUIT OPENING
16,5 LOCATION 29,4
[.65] 41,1 [1.16]
[1.62]
25,4 18,8
47,8
[1.00] [1.88]
[.74]
39,0 26,4
[1.54] 2X 5,2 [.20] MTG HOLES 2X 10-32 UNF
[1.04]
38,1 TAPPED FROM REAR ONLY
44,5 2X 10-32 UNF
[1.75] [1.50]
TAPPED FROM REAR ONLY 2X 5,2 [.20] MTG HOLES
45,3 9,5 [.37] C'BORE X 7,8 [.31] DEPTH
[1.78]
DIMS: MM
[IN] DIMS: MM
[IN]
LSW SPDT PLUG-IN PRODUCT DIMENSIONS LSW DPDT PLUG-IN PRODUCT DIMENSIONS
(FOR REFERENCE ONLY) (FOR REFERENCE ONLY)
LSW SPDT NON PLUG-IN PRODUCT DIMENSIONS LSW DPDT NON PLUG-IN PRODUCT DIMENSIONS
26 sensing.honeywell.com
MICRO SWITCH Heavy-Duty Limit Switch, HDLS Series
Figure 22. MICRO SWITCH HDLS LSG Series maintained Figure 23. MICRO SWITCH HDLS LSG Series maintained
contact side plunger (single pole) dimensions contact side plunger (double pole) dimensions
19,0 2X n 25,4
[.75] [1.00]
19,0 2X 25,4
[.75] 119,1
[1.00] [4.69] 59,4
89,7 [2.34]
59,4 82,6
74,9 [3.53]
[2.34] 70,4 [3.25]
[2.95] [2.77]
CONDUIT OPENING
LOCATION 29,4
29,4 [1.16]
CONDUIT OPENING [1.16]
LOCATION 47,8
16,5 18,8 [1.88]
[.65] 41,1 [.74]
25,4 [1.62] 26,4 2X 10-32 UNF
[1.04] TAPPED FROM REAR ONLY
[1.00] 38,1
39,1 [1.50] 2X 5,2 [.20] MTG HOLES
[1.54] 2X 5,2 [.20] MTG HOLES
45,3 9,5 [.37] C'BORE X 7,8 [.31] DEPTH
44,5 2X 10-32 UNF [1.78]
[1.75] TAPPED FROM REAR ONLY
25,4 2X 25,4
19,0 19,0
[1.00] [.75] [1.00]
[.75]
101,7
119,1
[4.0] 75,8 [4.69] 59,4
[2.98] 59,4
70,4 89,7 [2.34]
[2.34] 82,6
[2.77] [3.53]
[3.25]
20,3 29,4
[.80] [1.16] 21,3 29,4
[.84] [1.16]
36,6 38,1
[1.44] 41,1 47,8
[1.62] [1.50] [1.88]
39,0
[1.54] CONDUIT OPENING
2X 5,2 [.20] MTG HOLES LOCATION 45,3
CONDUIT OPENING 44,4 [1.78] 2X 10-32 UNF
LOCATION [1.75] TAPPED FROM REAR ONLY
2X 10-32 UNF
TAPPED FROM REAR ONLY 2X 5,2 [.20] MTG HOLES
8,0 [.32] C'BORE X 7,8 [.31] DEPTH
1-2
3-4
3-4
1-2
1-2
3-4
3-4
1-2
1 2
1-2
3-4
3-4
1-2
0 1 2
0
0
1-2
3-4
3-4
1-2
1-2
3-4
3-4
1-2
8 0 0
12
16 10
20 16
20 15
25 25
Snap Action Snap Action
Snap Action Snap Action Snap Action
2NO/2NC 2NO/2NC
2NO/2NC 2NO/2NC 2NO/2NC
Contact closed n 3 4 3 4
3 3 3 4
Contact open o 4
1 2
4
1 2
1 2
1 2 1 2
7 7 7 8
7 8 7 8
8 8 5
5 5 6 6
5 6 5
6 6
1-2/5-6
3-4/7-8
3-4/7-8
1-2/5-6
1-2/5-6
3-4/7-8
3-4/7-8
1-2/5-6
1-2/5-6
3-4/7-8
3-4/7-8
1-2/5-6
1-2/5-6
3-4/7-8
3-4/7-8
1-2/5-6
1-2/5-6
3-4/7-8
3-4/7-8
1-2/5-6 0 0
0
0 0
10
8 15
12 16
20 16 25 25
20
Lever length 8A act.: 140 mm [5.5 in] SST
Actuator: Actuator: Actuator:
from top mount- 8C act.: 140 mm [5.5 in]
140 mm [5.5 in] 140 mm [5.5 in] 330 mm [13 in]
ing hole steel plated
Pretravel 25,4 mm [1.0 in] 38,0 mm [1.5 in] 102 mm [4.0 in] 51,0 mm [2.0 in]
LSJ1A-7A LSJ1A-7M LSJ1A-7N LSK1A- LSK1A- Oper. force 2,78 Nm [10 oz] 1,95 Nm [7 oz] 1,39 Nm [5 oz] 8A: 1,39 Nm [5 oz];
- Plastic - Spring - Flexible 8A - Cat 8C - Coil 8C: 1,95 Nm [7 oz]
rod wire actuator whisker spring
Op. temp range3 -12C to 93C [10F to 200F] (for low temp, high temp, or preleaded versions, see pages 8-9)
Circuitry Contacts Body Style 2
Conduit Options
(NPT)
Silver Plug-in 0.5 in LSJ1A-7A LSJ1A-7N LSJ1A-7M LSK1A-8A LSK1A-8C
Gold4 Plug-in 0.5 in LSJ1E-7A LSJ1E-7M LSK1E-8A LSK1E-8C
SPDT
Silver Plug-in 0.5 in LSJ6B-7A LSJ6B-7N LSJ6B-7M LSK6B-8A LSK6B-8C
DPDT
28 sensing.honeywell.com
MICRO SWITCH Heavy-Duty Limit Switch, HDLS Series
Figure 24. MICRO SWITCH HDLS LSJ_ _-7A Series wobble Figure 25. MICRO SWITCH HDLS LSJ_ _-7A Series wobble
(single pole) dimensions (double pole) dimensions
23,6 39,6
[1.56] 21,6 [1.56]
14,7 14,7
21,6 [.85] 6,4 [.58]
[.85] [.58]
6,4 [.25]
[.25]
139,7
139,7 [5.50]
[5.50]
59,5
[2.34]
59,4 82,6
74,9 [2.34] 70,4 [3.25]
[2.77] 89,7
[2.95] [3.53]
139,7
[5.50]
139,7
[5.50]
59,5
[2.34]
89,7 82,6
59,4 [3.53] [3.25]
75,8 70,4
[2.98] [2.34]
[2.77]
29,4
29,4 CONDUIT OPENING [1.16]
CONDUIT OPENING [1.16] LOCATION
LOCATION 47,8
20,3 41,1 21,3
[.80] [1.88]
[1.62] [.84]
36,6
[1.44] 38,1
39,0 [1.50] 2X 10-32 UNF
2X 5,2 [.20] MTG HOLES 45,3 TAPPED FROM REAR ONLY
[1.54]
44,4 [1.78]
[1.75] 2X 10-32 UNF 2X 5,2 [.20] MTG HOLES
TAPPED FROM REAR ONLY 8,0 [.32] C'BORE X 7,8 [.31] DEPTH
DIMS: MM
DIMS: MM [IN]
[IN]
LSJ PLASTIC ROD DPDT NON PLUG-IN PRODUCT DIMENSIONS
(FOR REFERENCE ONLY)
LSJ PLASTIC ROD SPDT NON PLUG-IN PRODUCT DIMENSIONS
(FOR REFERENCE ONLY)
139.7 139,7
[5.50] [5.50]
MTG PADS
15,2
15,2 63,5 [.60] 63,5
[.60] [2.50] [2.50]
MTG PADS
26,4
[1.04]
59,4 59,5
[2.34] 70,4 [2.34]
74,9 82,6
[2.77]
[2.95] [3.25]
89,7
[3.53]
29,4
CONDUIT OPENING [1.16] CONDUIT OPENING
LOCATION LOCATION
16,5 29,4
[.65] 41,1 [1.16]
[1.62] 18,8
25,4
[1.00] [.74] 47,8
39,0 26,4 [1.88]
[1.54] 2X 5,2 [.20] MTG HOLES [1.04] 2X 10-32 UNF
38,1
TAPPED FROM REAR ONLY
44,5 [1.50]
2X 10-32 UNF
[1.75] TAPPED FROM REAR ONLY 45,3 2X 5,2 [.20] MTG HOLES
[1.78] 9,5 [.37] C'BORE X 7,8 [.31] DEPTH
DIMS: MM
[IN] DIMS: MM
[IN]
LSJ FLEXIBLE CABLE SPDT PLUG-IN PRODUCT DIMENSIONS LSJ FLEXIBLE CABLE DPDT PLUG-IN PRODUCT DIMENSIONS
SPDT Non-plug-in
(FOR REFERENCE ONLY) DPDT Non-plug-in
(FOR REFERENCE ONLY)
(mm[in]) (mm[in])
39,6
21,6 39,6 [1.56]
[.850] [1.56] 14,7 21,6 14,7
[.58] [.85] 6,4 [.58]
4.75 [.25]
[1.87]
139,7
[5.5]
139,7
[5.50]
MTG PADS
63,5
[2.50]
15,2
[.60] 63,5 26,4
MTG PADS [1.04]
[2.50]
59,4
89.7 [2.34]
82,6
[3.53]
[3.25]
75,8 59,4
[2.34] 70,4
[2.98] [2.77]
CONDUIT OPENING
LOCATION 29,4
[1.16]
CONDUIT OPENING 29,4
LOCATION 21,3 47,8
[1.16]
[.84] [1.88]
20,3 41,1
38,1
[.80] [1.62] [1.50] 2X 10-32 UNF
36,6 45,3 TAPPED FROM REAR ONLY
[1.44] [1.78]
2X 5,2 [.20] MTG HOLES
39,0 2X 5,2 [.20] MTG HOLES
[1.54] DIMS: MM 8,0 [.32] C'BORE X 7,8 [.31] DEPTH
2X 10-32 UNF
44,4 TAPPED FROM REAR ONLY [IN]
[1.75]
DIMS: MM
[IN]
LSJ FLEXIBLE CABLE DPDT NON PLUG-IN PRODUCT DIMENSIONS
(FOR REFERENCE ONLY)
330,2
[13.00]
66,8
330,2
15,2 [2.63]
[13.00]
[.60]
26,4
[1.04]
59,5
[2.34]
82,6
[3.25]
74,9 59,4
[2.34] 70,4 89,7
[2.95] [2.77] [3.53]
2,0 21,6
[.08] 21,6 [.85]
21,6
[.85] [.85] 39,6
21,6
39,6 [1.56]
[.85]
[1.56]
330,2
330,2 [13.00]
[13.00] 66,8
66,8 MTG PADS [2.63]
[2.63] 15,2
MTG PADS 15,2
[.60] [.60]
26,4
26,4 [1.04]
[1.04]
59,5
[2.34]
75,8 59,4 89,7 82,6
[2.98] [2.34] 70,4 [3.53] [3.25]
[2.77]
139,7
[5.50]
139,7
[5.50]
MTG PADS
15,2 15,2
[.60] 65,0 [.60] 65,0
[2.56] [2.56]
26,4 MTG PADS 26,4
[1.04] [1.04]
29,4
CONDUIT OPENING [1.16]
LOCATION CONDUIT OPENING
41,1 29,4
16,5 LOCATION
[1.62] [1.16]
[.65] 18,8
25,4 [.74] 47,8
[1.00] 26,4 [1.88]
39,0 2X 5,2 [.20] MTG HOLES [1.04]
[1.54] 38,1 2X 10-32 UNF
44,5 2X 10-32 UNF [1.50] TAPPED FROM REAR ONLY
[1.75] TAPPED FROM REAR ONLY 45,3
[1.78] 2X 5,2 [.20] MTG HOLES
9,5 [.37] C'BORE X 7,8 [.31] DEPTH
DIMS: MM
[IN]
LSK
SPDTCATNon-plug-in
WHISKER SPDT PLUG-IN PRODUCT DIMENSIONS DPDT Non-plug-in
(FOR REFERENCE ONLY) LSK CAT WHISKER DPDT PLUG-IN PRODUCT DIMENSIONS
(mm[in]) (mm[in])
1,3
(FOR REFERENCE
1,3
ONLY)
[.05] [.05] 39,6
39,6
[1.56]
[1.56] 21,6
21,6 14,7 14,7
[.85] [.58] [.85] [.58]
139,7
139,7 [5.50]
[5.50]
59,5
89,7 [2.34]
59,4 70,4 82,6
[3.53]
[2.34] [2.77] [3.25]
75,8
[2.98]
140
140 [5.50]
[5.50]
59,5
[2.34]
59,4 82,6
74,9 [2.34] 70,4 [3.25]
[2.95] [2.77]
89,7
[3.53]
DIMS: MM
[IN]
LSJ SPRING WIRE DPDT PLUG-IN PRODUCT DIMENSIONS
SPDT Non-plug-in DPDT Non-plug-in
LSK COIL SPRING SPDT PLUG-IN PRODUCT DIMENSIONS (FOR REFERENCE ONLY)
(mm[in]) (FOR REFERENCE ONLY) 39,6
(mm[in]) 39,6
21,6 21,6 [1.56]
[.850] [1.56]
[.850] 14,7
14,7 6.35
6,35 [.25] [.58]
[.58]
[.25]
140 140
[5.50] [5.50]
59,5
75,8 59,4 [2.34]
[2.34] 70,4 82,6
[2.98] [2.77] [3.25]
89,7
[3.53]
0.75 in conduit
0
LSQ052 Double pole, plug-in, 0.75
in conduit 9
17
75
LSQ053 Single pole, non-plug-in,
1-2
3-4
3-4
1-2
0.5 in conduit 0
75
LSZ616 Replacement lever for above listings
Pretravel 17 max.
Diff. travel 8 max.
Overtravel 58 min.
Oper. torque 0,45 Nm [4 in-lb] max.
Action CW and CCW (spring return)
34 sensing.honeywell.com
MICRO SWITCH Heavy-Duty Limit Switch, HDLS Series
SPECIAL APPLICATIONS
Gravity Return Side Rotary Switches (LSS) Extra Low Torque Side Rotary Switches (LST)
LSS1H gravity-return, side-rotary switches have no return LST1H extra-low torque, side-rotary switches have a low force
spring mechanism. The weight of the actuating lever must pro- return spring and a maximim operation torque of 12 in-oz. It is
vide the force to restore it to the free position. The 5 in-oz. max. rated as NEMA 1 due to an unsealed head. The switch cavity is
operating torque is useful in conveyor applications since it sealed to protect the switch contacts.
enables operation by small or lightweight objects. Because the
head is unsealed, the LSS1H is classified as NEMA 1. However, LST1H
the switch cavity is sealed to protect the switch contacts. Description Extra-low torque side rotary
Circuitry SPDT, double break
LSS1H
1-2
3-4
3-4
1-2
Contacts Silver
0
Description Gravity-return side Sealing NEMA 1
rotary 10
Electrical rating (B) NEMA B600 15
Circuitry SPDT, double break
Body style Plug-in
Contacts Silver
Conduit (NPT) 0.5 in
Sealing NEMA 1
Pretravel 15 max.
Electrical rating (B) NEMA B600
Differential travel 5 max.
Body style Plug-in
Overtravel 60 min.
Conduit (NPT) 0.5 in
Total travel 75 nom. 75
Differential travel 12 max.
Operating torque 0,085 Nm [12 in-oz] max.
Total travel (no stop)* 360
NOTE: Same polarity each pole.
Operating torque 0,035 Nm [5 in-oz]
max.
* Switch has approximately 180 dwell of the
normally closed and normally open switch contacts.
NOTE: Same polarity each pole.
ALSO AVAILABLE
Fully potted MICRO SWITCH HDLS heavy-duty limit switches provide an extra degree of protection in
harsh environments by sealing the basic switch cavity with epoxy. These switches are the same as the non-
plug-in HDLS except that the entire switch cavity is filled with epoxy in addition to the conduit entrance. The
fully potted HDLS switches are pre-leaded, with either cable or connectors.
Excellent sealing capability for harsh-duty food and beverage wash downs and severe machine tool envi-
ronments
Diaphragm sealing
12 inch STOOW-A cable (other lengths available) or connector version
Cable versions: NEMA 1, 6, 6P, 12
Connector versions: NEMA 1, 6, 6P, 12, 13
All fluorocarbon seals (low temperature fluorosilicone seals available)
UL, CSA, CE, CCC
MICRO SWITCH HDLS switches are also available in all stainless-steel versions. Designed for use in
highly corrosive environments, such as petrochemical plants, food processing plants, shipboard, and dock-
side locations. The type 316 cast stainless steel body is designed to minimize crevices where food particles
could become trapped in water. The actuator, operating head, and screws are also stainless steel. All seals
are fluorocarbon to provide excellent chemical resistance and to withstand operating temperatures up to
121C [250F] and pressurized steam cleaning. Pre-leaded and epoxy-filled versions also available.
36 sensing.honeywell.com
ADDITIONAL INFORMATION
m WARNING
The following associated literature is available on the Web at
sensing.honeywell.com:
PERSONAL INJURY
Product installation instructions DO NOT USE these products as safety or emergency stop
devices or in any other application where failure of the
Product range guide product could result in personal injury.
Product nomenclature tree Failure to comply with these instructions could result in
Product application-specific information death or serious injury.
Application Note: Sensors and Switches in Oil Rig
Applications
m WARNING
Application Note: Sensors and Switches for Industrial
MISUSE OF DOCUMENTATION
Manual Process Valves
The information presented in this product sheet is for
Application Note: Sensors and Switches Used in Valve reference only. Do not use this document as a product
Actuators and Valve Positioners installation guide.
Complete installation, operation, and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Warranty/Remedy
Honeywell warrants goods of its manufacture as being free of
defective materials and faulty workmanship during the appli-
cable warranty period. Honeywells standard product warranty
applies unless agreed to otherwise by Honeywell in writing;
please refer to your order acknowledgement or consult your
local sales office for specific warranty details. If warranted
goods are returned to Honeywell during the period of coverage,
Honeywell will repair or replace, at its option, without charge
those items that Honeywell, in its sole discretion, finds defec-
tive. The foregoing is buyers sole remedy and is in lieu of all
other warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special,
or indirect damages.