Professional Documents
Culture Documents
JVC Stereo Receiver Manual PDF
JVC Stereo Receiver Manual PDF
RX-5020VBK / RX-5022VSL
UP UP
STANDBY
MASTER VOLUME
PTY–PTY SEARCH–PTY MEMORY
DOWN DOWN
STANDBY/ON
D I G I T A L
SURROUND
SOURCE NAME
PHONES
INSTRUCTIONS
For Customer Use:
Enter below the Model No. and Serial
No. which are located either on the rear,
bottom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
LVT0850-001A
[J]
Table of Contents
Getting Started ........................................... 3
Before Installation ...................................................................... 3
Checking the Supplied Accessories ........................................... 3
Putting Batteries in the Remote Control .................................... 3
Connecting the FM and AM Antennas ....................................... 4
Connecting the Speakers ............................................................ 5
Connecting Audio/Video Components ....................................... 6
Connecting the Power Cord ....................................................... 7
Basic Operations ......................................... 8
Turning On the Power ................................................................ 8
Selecting the Source to Play ....................................................... 8
Adjusting the Volume ................................................................. 9
Listening Only with Headphones ............................................... 9
Turning Off the Sounds Temporarily—Muting ........................ 10
Turning Off the Power with the Sleep Timer ........................... 10
Basic Settings ........................................... 11
Setting the Digital Input (DIGITAL IN) Terminals ................. 11
Selecting the Analog or Digital Input Mode ............................ 11
Setting the Speaker Information ............................................... 12
Sound Adjustments .................................... 15
Attenuating the Input Signal .................................................... 15
Adjusting the Front Speakers Output Balance ......................... 15
Adjusting the Tone ................................................................... 15
Adjusting the Subwoofer Output Level .................................... 15
Tuner Operations ....................................... 16
Tuning in Stations Manually .................................................... 16
Using Preset Tuning ................................................................. 16
Selecting the FM Reception Mode ........................................... 17
Creating Realistic Sound Fields ................... 18
About Relations between Speaker Layout and
Surround Modes ................................................................. 20
Using Dolby Pro Logic II, Dolby Digital and
DTS Digital Surround ........................................................ 21
Using DAP Modes and All Channel Stereo ............................. 23
COMPU LINK Remote Control System ......... 24
Operating JVC's Audio/Video
Components .......................................... 25
Operating Audio Components .................................................. 25
Operating Video Components .................................................. 27
Operating Other Manufacturers' Video
Equipment ............................................ 28
Troubleshooting ......................................... 30
Specifications ............................................ 31
1
EN01-07.RX-5020/5022V[J]_f 1 01.12.7, 8:47 AM
Parts Identification
Front Panel
1 2 3 45 6 7 89 p
UP UP
ANALOG SPK TUNED STEREO AUTO MUTING SLEEP
STANDBY
DIGITAL AUTO L C R PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT VOLUME
MEMORY LINEAR PCM S.WFR LFE
LS S RS
MASTER VOLUME
DOWN DOWN DIGITAL
STANDBY/ON CH-
D I G I T A L
SURROUND
INPUT ATT
SOURCE NAME
PHONES
q w e r t y u i o
5 e Remote Control
TAPE/CDR CD DVD 1 TV/CATV selector (27, 28)
2 • 10 keys for selecting preset channels (17)
6 FM/AM TV SOUND VCR
ANALOG
/DIGITAL • 10 keys for adjusting sound (15, 22, 23)
r • 10 keys for operating audio/video components (25 – 29)
FM MODE 3 SOUND button (15, 22, 23)
7 4 Operating buttons for audio/video components
ON/OFF
t (25 – 27, 29)
TV/VIDEO SURROUND MUTING
8 MODE y 5 REC PAUSE button (26, 27, 29)
6 Source selecting buttons (8, 9, 11, 12, 17, 25 – 29)
9 u TAPE/CDR, CD, DVD, FM/AM, TV SOUND, VCR
7 FM MODE button (17)
p VCR CH TV/CATV CH TV VOLUME i 8 TV/VIDEO button (27, 28)
9 TV/CATV CH (channel) +/– buttons (27, 28)
VOLUME
p VCR CH (channel) +/– buttons (27, 29)
q STANDBY/ON buttons (8, 27 – 29)
REMOTE CONTROL RM - SRX5020J
AUDIO, TV/CATV, VCR, DVD
w SLEEP button (10)
e CD-DISC button (26)
r ANALOG/DIGITAL button (11, 12)
t SURROUND ON/OFF and SURROUND MODE buttons
(20, 21, 23, 25)
y MUTING button (10)
u TV VOLUME +/– buttons (27, 28)
i VOLUME +/– button (9)
2
EN01-07.RX-5020/5022V[J]_f 2 01.12.7, 8:47 AM
Getting Started
• Batteries (2)
• FM Antenna (1)
CAUTION:
Follow these precautions to avoid leaking or cracking cells:
• Place batteries in the remote control so they match the polarity:
(+) to (+) and (–) to (–).
• Use the correct type of batteries. Batteries that look similar may
differ in voltage.
• Always replace both batteries at the same time.
• Do not expose batteries to heat or flame.
3
EN01-07.RX-5020/5022V[J]_f 3 01.12.7, 8:47 AM
Getting Started
75
or
FMAXIAL 75
FMAXIAL
CO CO
FM antenna (supplied)
Snap the tabs on the loop Extend the supplied FM antenna horizontally.
into the slots of the base
to assemble the AM loop
antenna.
AM
LOOP
AM
EXT
NT
FROKERS
EA FT
SP T LE +
RIGH
CE
N: DAN
R
REA RS
– TIO IMPE
NA + CAU KER
TEN FM 75IAL EAKE + SPEA16
1 2 3
AN SP LEFT
TER
AX
CO T 8
CEN KER RIGH
SP
EA –
–
K-4 +
LIN O)
MPU R
CO(SYNCH
OR
–
NIT
MOOUT AM
AM
OP EXIT
LO
1
ITAL ) LEFT DVD
DIG(DVD T
RIGH
CD T
OU )
(REC
) OUT DVD VC
R
CD )
2( (REC AU
DIO INY)
ITAL TAPE (PLA O
DIG R VIDE
/CD
INY)
(PLA
IN
ITAL
DIG T
OU )
(REC
R
VC
INY) FER
OO
(PLA BW
SU OUT
FT
LE
D
UN T
SO RIGH DIO
TV AU
AM antenna connection
Connect the AM loop antenna supplied to the AM LOOP
terminals.
Turn the loop until you have the best reception.
• If the reception is poor, connect an outdoor single vinyl-
covered wire (not supplied) to the AM EXT terminal. (Keep the
AM loop antenna connected.)
4
EN01-07.RX-5020/5022V[J]_f 4 01.12.7, 8:47 AM
Connecting the Speakers Speaker layout diagram
Getting Started
After connecting the front, center, rear speakers and/or a subwoofer, “YES” for the subwoofer and “SMALL” for the front, center
set the speaker setting information properly to obtain the best and rear speakers are initial settings. To get best possible
possible Surround effect. For details, see pages 12 to 14. sound, change the subwoofer and speaker settings to fit your
listening conditions (See pages 12 and 13).
CAUTION:
Use speakers with the SPEAKER IMPEDANCE indicated by the
speaker terminals.
Center
Connecting the front, center and rear speakers speaker
STANDBY
MASTER VOLUME
1
MEMORY
STANDBY/ON D I G I T A L
SURROUND
SURROUND ON/OFF
INPUT ANALOG INPUT DIGITAL ADJUST SETTING
CONTROL
SURROUND MODE SPEAKERS ON/OFF DOWN UP
CD TAPE/CDR FM/AM
SOURCE NAME
PHONES
REARERS
– ION IMP
NA 75 + CAUT ER
AN
TEN FM XIAL EAK
SP LEFT + SPEAK
16
COA TER HT 8
CEN ER RIG
SP
EAK –
–
K-4 +
U LIN O)
MP HR
CO(SYNC
OR
–
NIT AM
MOOUT AMP
EXIT
LOO
L1 T D
ITA LEF
DIG(DVD) DV
HT
RIG
CD T
OUC)
(RE
Powered subwoofer BW
OO
FER
SU OUT
To
subwoofer
SUBWOOFER
OUT
NT
FROKERS
EA FT +
SP T LE
H
RIG
Connect the input jack of a powered subwoofer to the N : ED
AN
CE
R
REAERS
– TIO IMP
SUBWOOFER OUT jack on the rear panel, using a cable with RCA EAK
SP LEFT +
+ CAUAKER
E
SP 16
To left
TER HT front speaker
pin plugs (not supplied). CEN KER
EA
RIG 8
SP –
• Refer also to the manual supplied with your subwoofer. –
+
5
EN01-07.RX-5020/5022V[J]_f 5 01.12.7, 8:47 AM
Getting Started
Cassette deck
Turn off all components before connections.
To audio input PHONO To audio output
You can connect the following audio/video components to this
receiver. Refer also to the manuals supplied with your components. CD
TV SOUND
TV
TV CD
RIGHT LEFT
AUDIO OUT MONITOR
(REC) OUT
TAPE
CDR
IN DVD
(PLAY)
VIDEO
TV SOUND
RIGHT LEFT
AUDIO
To video input
6
EN01-07.RX-5020/5022V[J]_f 6 01.12.7, 8:48 AM
VCR IMPORTANT:
Getting Started
• When connecting the DVD player or digital TV using the digital
A VCR C terminal, you also need to connect it to the video jack on the rear.
Without connecting it to the video jack, you can view no playback
picture.
• After connecting the components using the DIGITAL IN terminals,
B D set the followings correctly if necessary:
– Set the digital input (DIGITAL IN) terminal setting correctly. For
details, see “Setting the Digital Input (DIGITAL IN) Terminals” on
CD page 11.
– Select the digital input mode correctly. For details, see “Selecting
OUT MONITOR the Analog or Digital Input Mode” on page 11.
(REC) OUT
TAPE
CDR
IN DVD
(PLAY) Digital TV
OUT OUT
(REC) (REC)
DVD player
VCR VCR
IN IN
(PLAY) (PLAY)
VIDEO
TV SOUND
DVD
protective plug.
DVD
AUDIO
OUT
(REC)
VCR
IN
(PLAY) Notes:
VIDEO • When shipped from the factory, the DIGITAL IN terminals have
Å To front left/right channel audio output (or to audio mixed been set for use with the following components.
– DIGITAL 1 (coaxial): For DVD player
output)
– DIGITAL 2 (optical): For CD player
ı To video output
• When you want to operate the CD player or CD recorder using the
COMPU LINK remote control system, connect the target
component also as described in “Analog connections” (see page 6).
Note:
To enjoy the software encoded with Dolby Digital or DTS Digital
Surround, you must connect the DVD player using the digital terminal Connecting the Power Cord
on the rear of this receiver. (See “Digital connections” below.)
Before plugging the power cord into an AC outlet, make sure that all
connections have been made.
Digital connections Plug the power cord into an AC outlet.
This receiver is equipped with two DIGITAL IN terminals—one
CAUTIONS:
digital coaxial terminal and one digital optical terminal.
You can connect any component to one of the digital terminals using • Do not touch the power cord with wet hands.
• Do not pull on the power cord to unplug the cord. When
a digital coaxial cable (not supplied) or digital optical cable (not
unplugging the cord, always grasp the plug so as not to damage
supplied).
the cord.
7
EN01-07.RX-5020/5022V[J]_f 7 01.12.7, 2:26 PM
Basic Operations
TEST
1
EFFECT
2
CENTER
REAR L
3
AUDIO
STANDBY/
ON
TV/CATV
4 5 6
AUDIO/VIDEO CONTROL RECEIVER MENU REAR R VCR
STANDBY/ON
DOWN
D I G I T A L
DOWN DIGITAL LS S RS
CH-
SOUND
PTY–PTY SEARCH–PTY
REW FF
SLEEP
SURROUND
INPUT ATT
INPUT DIGITAL ADJUST SETTING
Source TAPE/CDR CD DVD
SOURCE NAME
buttons FM MODE
ON/OFF
CH-
The STANDBY lamp on the front panel lights up. 1 Press TAPE/CDR (SOURCE NAME). TAPE/CDR
A small amount of power is consumed in standby mode. To turn the 2 Press and hold SOURCE NAME
power off completely, unplug the AC power cord.
(TAPE/CDR) until “ASSIGN CDR” appears on the display.
TAPE/CDR CD DVD
Without changing the source name, you can still use the connected
component. However, there may be some inconvenience.
CD TAPE/CDR FM/AM
FM/AM TV SOUND VCR – “TAPE” will appear on the display when you select the CD
recorder.
SOURCE NAME – You cannot use the digital input (see page 11) for the CD recorder.
– You cannot use the COMPU LINK remote control system (see page
On the front panel From the remote control 24) to operate the CD recorder.
8
EN08-17.RX-5020/5022V[J]_f 8 01.12.7, 8:48 AM
Selecting different sources for picture and
Basic Operations
Listening Only with Headphones
sound
You can watch picture from a video component while listening to You must turn off the speakers when you listen with headphones.
sound from another component.
1 Connect a pair of headphones to the PHONES jack on the front
Press one of the audio source selecting buttons (CD, TAPE/CDR, panel.
FM/AM), while viewing the picture from a video component such as
the VCR or DVD player, etc. 2 Press SPEAKERS ON/OFF.
DVD VCR TV SOUND TAPE/CDR CD DVD
• “HEADPHONE” appears for a while and the H. PHONE
indicator lights up on the display.
FM/AM TV SOUND VCR
CD TAPE/CDR FM/AM The H. PHONE indicator lights up.
ANALOG
SOURCE NAME L R H.PHONE
Note: This cancels the Surround mode currently selected, and activates
Once you have selected a video source, pictures of the selected the HEADPHONE mode.
source are sent to the TV until you select another video source.
Note:
The volume level can be adjusted within the range of “0” (minimum) to
“50” (maximum).
9
EN08-17.RX-5020/5022V[J]_f 9 01.12.7, 3:56 PM
Basic Operations
CH-
• Subwoofer output level (see page 15)
• Surround mode selection (see pages 21 – 23 )
Notes:
• You cannot assign and store different settings for digital input
To restore the sound, press MUTING again. mode and analog input mode.
• Turning MASTER VOLUME on the front panel or pressing • If the source is FM or AM, you can assign a different setting for
VOLUME +/– on the remote control also restores the sound. each band.
For recording
You can record any sources playing through the receiver to a
Turning Off the Power Remote cassette deck (or a CD recorder) connected to the TAPE/CDR
with the Sleep Timer ONLY jacks and the VCR connected to the VCR jacks at the same time.
You can fall asleep while listening to music—Sleep Timer. While recording, you can listen to the selected sound source at
whatever sound level you like without affecting the sound levels
Press SLEEP on the remote control repeatedly. SLEEP of the recording.
• The SLEEP indicator lights up on the display, and the
shut-off time changes in 10 minutes intervals. Note:
The output volume level, tone adjustment (see page 15), and
ANALOG SPK
L C R
SLEEP Surround modes (see page 18) cannot affect the recording.
S.WFR LFE
LS S RS
0 (Canceled) 90 80 70 L C R ANALOG
DIGITAL AUTO
SPK
L C R
ONETOUCH
PRO LOGIC ΙΙ L C R
LINEAR PCM S.WFR LFE
DIGITAL LS S RS
S.WFR LFE CH- S.WFR LFE
LS S RS LS S RS
When the shut-off time comes
The receiver turns off automatically. The following signal indicators light up—:
L : •When digital input is selected: Lights up when the left
To check or change the time remaining until the shut-off time channel signal comes in.
Press SLEEP once. • When analog input is selected: Always lights up.
The remaining time (in minutes) until the shut-off time appears. R : • When digital input is selected: Lights up when the right
• To change the shut-off time, press SLEEP repeatedly. channel signal comes in.
• When analog input is selected: Always lights up.
To cancel the Sleep Timer C : When the center channel signal comes in.
Press SLEEP repeatedly until “SLEEP 0 MIN” appears on the LS : When the left rear channel signal comes in.
display. (The SLEEP indicator goes off.) RS : When the right rear channel signal comes in.
• Turning off the power also cancels the Sleep Timer. S : When the monaural rear channel signal or 2 channel Dolby
Surround encoded signal comes in.
LFE: When the LFE channel signal comes in.
Note:
When “SUBWOOFER” is set to “YES” (see page 12), S.WFR lights
up.
10
EN08-17.RX-5020/5022V[J]_f 10 01.12.7, 2:14 PM
Basic Settings
UP UP
ENTER SUBWOOFER DVD
ANALOG SPK TUNED STEREO AUTO MUTING SLEEP
STANDBY
DIGITAL AUTO L C R PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT VOLUME MASTER VOLUME 10 0 10
MEMORY LINEAR PCM S.WFR LFE
RETURN 100 SLEEP
DIGITAL LS S RS
DOWN DOWN
CH- SOUND
STANDBY/ON
D I G I T A L
PTY–PTY SEARCH–PTY
REW FF
SURROUND
INPUT ATT
INPUT DIGITAL ADJUST SETTING
VOLUME
Setting the Digital Input Remote Selecting the Analog or Digital Input
[DIGITAL IN] Terminals NOT Mode
When you use the digital input terminals, register what components When you have connected digital source components using both the
are connected to which terminals (DIGITAL 1/2) so that the correct analog connection (see page 6) and the digital connection (see page
source name will appear when you select the digital source. 7) methods, you need to select the input mode correctly.
Before you start, remember...
There is a time limit in doing the following steps. If the setting is 1 Press one of the source selecting buttons—DVD,
canceled before you finish, start from step 1 again. TV SOUND, CD, or TAPE/CDR*—for which you
want to change the input mode.
1 Press SETTING repeatedly until SETTING DVD VCR TV SOUND
TAPE/CDR CD DVD
S.WFR LFE
LS S RS
Note:
DIGITAL 1 terminal setting
* Among the sources listed above, you can select the digital input
* “1DVD 2CD” is the initial setting. If you have already only for the sources which you have selected the digital input
changed the setting, another combination will be shown. terminals for. (See “Setting the Digital Input (DIGITAL IN)
Terminals.”)
• Each time you press the button, the display “DIGITAL AUTO” appears on the display
changes to show the following: and the indicator for the detected signals also
lights up.
1 DVD 2 CD j 1 DVD 2 TV j 1 DVD 2 CDR j
1 CD 2 DVD j 1 CD 2 TV j 1 CD 2 CDR j To change the input mode back to analog INPUT ANALOG
as the digital input for the following components. • Each time you press the button, the input mode
– DIGITAL 1 (coaxial): For DVD player alternates between the analog input (“ANALOG”)
– DIGITAL 2 (optical): For CD player and the digital input (“DIGITAL AUTO”).
Remote
DIGITAL AUTO : Select this for the digital input mode. The Setting the Speaker Information NOT
receiver automatically detects the
incoming signal format. (The DIGITAL To obtain the best possible sound or effect from the Surround modes
AUTO indicator lights up on the display, (see page 18), register the following speakers and subwoofer
then the digital signal indicator for the information after all connections are completed.
detected signals lights up.)
ANALOG : Select this for the analog input mode. The followings are items you can set:
(Initial setting when shipped from the • Subwoofer information—SUBWOOFER
factory.) • Speaker size—FRNT SP, CNTR SP, REAR SP
• Speaker distance—UNIT, FRNT DIS, CNTR DIS, REAR DIS
If the following symptoms occur while playing Dolby Digital or • Crossover frequency—CROSS
DTS Digital Surround software with “DIGITAL AUTO” • Low frequency effect attenuator—LFE ATT
selected, follow the procedure below. • Dynamic range compression—D. COMP
• Sound does not come out at the beginning of playback.
• Noise comes out while searching or skipping chapters or tracks.
1 Press INPUT DIGITAL (or ANALOG/DIGITAL on the remote Before you start, remember...
control). There is a time limit in doing the following steps. If the setting is
• “DIGITAL AUTO” appears on the display. canceled before you finish, start from step 1 again.
CH-
• To play back software encoded with Dolby Digital, select 2 Press CONTROL UP 5/DOWN ∞ to CONTROL
DOWN UP
Note:
When “DIGITAL AUTO” cannot recognize the incoming signals, no
digital signal indicators light up on the display.
12
EN08-17.RX-5020/5022V[J]_f 12 01.12.7, 8:48 AM
Speaker size Speaker distance
Basic Settings
Register the sizes of all the connected speakers. Register the unit you use, then the speaker distance from your
• When you change your speakers, register the information about listening point.
the speakers again. • If you have set the unit before, start from step 3.
1 Press SETTING repeatedly until T SETTING 1 Press SETTING repeatedly until SETTING
LARGE : Select this when the speaker size is relatively large. “FRNT DIS (Front distance),” “CNTR
(See “Notes” below.) DIS (Center distance)” or “REAR DIS
SMALL : Select this when the speaker size is relatively small. (Rear distance)” (with the current setting)*
(See “Notes” below.) appears on the display.
NONE : Select this when you have not connected a speaker. The display shows the current setting in the unit selected in step 2.
(Not selectable for the front speakers) * “3.0m” is the initial setting for meter and “10FT” is for feet. If
you have already changed the setting, another value will be
shown.
3 Repeat steps 1 and 2 to select the appropriate
items for other speakers. 4 Press CONTROL UP 5/DOWN ∞ to CONTROL
DOWN UP
Note:
If you have selected “NONE” for the center and rear speakers
setting, you cannot set the speaker distance for the center and
rear speakers.
13
EN08-17.RX-5020/5022V[J]_f 13 01.12.7, 11:28 AM
Basic Settings
not take effect (“CROSS OFF” appears). ATT (Low Frequency Effect
Attenuator)” (with the current setting)*
1 Press SETTING repeatedly until SETTING
appears on the display.
“CROSS (Crossover)” (with the current * “0dB” is the initial setting. If you have already changed the
setting)* appears on the display. setting, “–10dB” will be shown.
* “150HZ” is the initial setting. If you have already changed the
setting, another frequency will be shown. 2 Press CONTROL UP 5/DOWN ∞ to CONTROL
DOWN UP
200HZ 150HZ
Note:
Crossover frequency is not valid for the HEADPHONE mode. Dynamic range compression
You can compress the dynamic range (difference between maximum
sound and minimum sound) of the reproduced sound. This is useful
when enjoying surround sound at night.
• This function takes effect only when playing back a source using
Dolby Digital.
OFF MID
MAX
OFF : Select this when you want to enjoy surround with its
full dynamic range. (No effect applied.)
MID : Select this when you want to reduce the dynamic range
a little.
MAX : Select this when you want to apply the compression
effect fully. (Useful at night.)
14
EN08-17.RX-5020/5022V[J]_f 14 01.12.7, 11:28 AM
Sound Adjustments
10
SUBWOOFER
0 10
DVD
SOUND
STANDBY MASTER VOLUME
DIGITAL AUTO L C R PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT VOLUME
MEMORY LINEAR PCM S.WFR LFE
PTY–PTY SEARCH–PTY
REW FF
DIGITAL LS S RS
DOWN DOWN
STANDBY/ON CH-
D I G I T A L
SOURCE NAME
PHONES
VCR CH TV/CATV CH TV VOLUME
VOLUME
indicator lights up on the display. adjust the bass or treble sounds level.
• Each time you press and hold the button, the Input Attenuator • Each time you press the button, the sound
mode turns on (“INPUT ATT ON”) or off (“INPUT level changes by ±2 steps.
NORMAL”).
Adjusting the Subwoofer Output Level
Adjusting the Front Speakers Remote
Output Balance NOT You can adjust the subwoofer output level if you have connected a
subwoofer and set the subwoofer information correctly—“YES.”
If the sounds you hear from the front right and left speakers are
On the front panel:
unequal, you can adjust the speakers output balance.
Before you start, remember...
Before you start, remember... There is a time limit in doing the following steps. If the setting is
There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
canceled before you finish, start from step 1 again.
1 Press ADJUST repeatedly until ADJUST SETTIN
15
EN08-17.RX-5020/5022V[J]_f 15 01.12.7, 8:49 AM
Tuner Operations
4 5
REAR L
6
TV/CATV
10 keys MENU
7/P 8
REAR R
9
VCR
PTY–PTY SEARCH–PTY
REW FF
FM/AM TUNING FM/AM PRESET FM MODE
UP UP
ANALOG SPK TUNED STEREO AUTO MUTING SLEEP
STANDBY MASTER VOLUME REC PAUSE CD–DISC
DIGITAL AUTO L C R PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT VOLUME
MEMORY LINEAR PCM S.WFR LFE
DIGITAL LS S RS
DOWN DOWN
STANDBY/ON CH-
D I G I T A L TAPE/CDR CD DVD
SURROUND
ANALOG
FM/AM TV SOUND VCR /DIGITAL
SURROUND ON/OFF
INPUT ANALOG INPUT DIGITAL
DVD VCR TV SOUND
ADJUST SETTING
FM/AM FM MODE
ON/OFF
SURROUND MODE
INPUT ATT
SPEAKERS ON/OFF
SOURCE NAME
VCR CH TV/CATV CH TV VOLUME
PHONES
VOLUME
MEMORY FM/AM
1 Press FM/AM to select the band Once a station is assigned to a channel number, the station can be
(FM or AM). quickly tuned. You can preset up to 30 FM and 15 AM stations.
The last received station of the selected band is tuned in.
To store the preset stations
FM/AM Remote
FM/AM
NOT
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
On the front panel From the remote control canceled before you finish, start from step 2 again.
CH-
LS S RS
CH-
CH-
Notes:
• When you press and hold FM/AM TUNING UP/DOWN in step 2, 3 Press FM/AM PRESET UP/ FM/AM PRESET
UP
the frequency keeps changing until a station is tuned in.
• When a station of sufficient signal strength is tuned in, the TUNED
DOWN to select a channel number
indicator lights up on the display. while the channel number position DOWN
CH-
16
EN08-17.RX-5020/5022V[J]_f 16 01.12.7, 8:49 AM
4 Press MEMORY again while the Selecting the FM Reception Mode
Tuner Operations
MEMORY
CH-
1 While listening to an FM station, press FM
MODE.
• Each time you press the button, the FM reception mode
5 Repeat steps 1 to 4 until you store all the stations alternates between “AUTO” and “MONO.”
you want.
FM MODE FM MODE
S.WFR LFE
CH-
(FM or AM).
The last received station of the selected band
ANALOG SPK TUNED
is tuned in. L C
S.WFR LFE
R
CH-
UP
hear monaural sounds. This mode is also useful to
suppress static noise between stations. The AUTO
until you find the channel you want. MUTING indicator lights up on the display.
• Pressing FM/AM PRESET UP increases (Initial setting)
DOWN
the channel numbers.
• Pressing FM/AM PRESET DOWN MONO : Select this to improve the reception (but stereo
decreases the channel numbers. effect will be lost).
In this mode, you will hear noise while tuning into
the stations. The AUTO MUTING indicator goes
From the remote control: off from the display. (The STEREO indicator also
goes off.)
1 Press FM/AM to select the band (FM or FM/AM
AM).
The last received station of the selected band is To restore the stereo effect
tuned in and the10 keys now work for tuner operation. Select “AUTO” in step 1.
• Each time you press the button, the band
alternates between FM and AM.
4 5 6
• For channel number 5, press 5. MENU REAR R
• For channel number 15, press +10 then 5. 7/P 8 9
• For channel number 20, press +10 then 10. ENTER SUBWOOFER
10 0 10
• For channel number 30, press +10, +10, RETURN 100
then 10.
17
EN08-17.RX-5020/5022V[J]_f 17 01.12.7, 8:49 AM
Creating Realistic Sound Fields
You can use the following Surround modes to reproduce a realistic Dolby Digital*
sound field: Used to reproduce multichannel sound tracks of the software
■ Dolby Surround encoded with Dolby Digital ( ). D I G I T A L
• Dolby Pro Logic II • To enjoy the software encoded with Dolby Digital, connect the
• Dolby Digital source component using the digital terminal on the rear of this
■ DTS Digital Surround receiver. (See page 7.)
■ DAP (Digital Acoustic Processor) modes
■ All Channel Stereo Dolby Digital 5.1 ch encoding method (so-called discrete
multichannel digital audio format) records and digitally compresses
the left front channel, right front channel, center channel, left rear
■ Dolby Surround channel, right rear channel, and LFE channel signals.
Since each channel is completely independent from the other
Dolby Pro Logic II*
channel signals to avoid interference, you can obtain much better
Dolby Pro Logic II has a newly developed multichannel playback sound quality with much stereo and surround effects.
format to decode all 2 channel sources—regular stereo source and
Dolby Surround encoded source—into 5.1 channel. Note:
Matrix-based encoding/decoding method for Dolby Pro Logic II Dolby Digital software can be roughly grouped into two categories
makes no limitation for the cutoff frequency of the rear treble and —multichannel (up to “5.1” channel) and 2 channel software. To enjoy
enables stereo rear sound compared to conventional Dolby Pro surround sounds while playing Dolby Digital 2 ch software, you can
Logic. use Dolby Pro Logic II.
Dolby Pro Logic II enables to reproduce spacious sound from
original sound without adding any new sounds and tonal colorations.
Dolby Pro Logic II has two modes—Movie mode and Music mode:
■ DTS Digital Surround**
Pro Logic II Movie (PL II MOVIE)—suitable for reproduction of Used to reproduce multichannel sound tracks of the software
Dolby Surround encoded sources bearing the mark DOLBY SURROUND .
encoded with DTS Digital Surround ( ).
You can enjoy soundfield very close to the one created with discrete • To enjoy the software encoded with DTS Digital Surround,
5.1 channel sounds. connect the source component using the digital terminal on the
Pro Logic II Music (PL II MUSIC)—suitable for reproduction of rear of this receiver. (See page 7.)
any 2 channel stereo music sources. You can enjoy wide and deep
sound by using this mode. For this mode, Panorama control can be DTS Digital Surround is another discrete multichannel digital
selected, which gives “wraparound” sound effect with side-wall audio format available on CD, LD, and DVD software.
image. Compared to Dolby Digital, audio compression ratio is relatively
• When Dolby Pro Logic II is activated, PRO LOGIC II low. This fact allows DTS Digital Surround format to add breadth
indicator lights up on the display. and depth to the reproduced sounds. As a result, DTS Digital
Surround features natural, solid and clear sound.
Center
speaker
STANDBY
MASTER VOLUME
MEMORY
STANDBY/ON D I G I T A L
SURROUND
CONTROL
SURROUND MODE SPEAKERS ON/OFF DOWN UP
CD TAPE/CDR FM/AM
SOURCE NAME
PHONES
* Manufactured under license from Dolby Laboratories. “Dolby,” “Pro ** Manufactured underlicense from Digital Theater Systems, Inc. US
Logic,” and the double-D symbol are trademarks of Dolby PAT. No. 5,451,942 and other world-wide patents issued and
Laboratories. Confidential unpublished works. ©1992–1997 Dolby pending. “DTS” and “DTS Digital Surround” are trademarks of
Laboratories, Inc. All rights reserved. Digital Theater Systems, Inc. Copyright 1996 Digital Theater
Systems, Inc. All rights reserved.
18
EN18-23.RX-5020/5022V[J]_f 18 01.12.7, 9:17 AM
■ DAP (Digital Acoustic Processor) modes ■ All Channel Stereo
Linear PCM 䡬 ⳯ ⳯ 䡬 䡬 䡬 䡬 䡬 䡬 䡬
Analog 䡬 ⳯ ⳯ 䡬 䡬 䡬 䡬 䡬 䡬 䡬
19
EN18-23.RX-5020/5022V[J]_f 19 01.12.7, 8:50 AM
Creating Realistic Sound Fields
Available Surround modes will vary depending on how many speakers are used with this receiver.
Make sure that you have set the speaker information correctly (see pages 12 to 14).
• If only front speakers are connected, you cannot use Surround modes.
• If rear speakers are not connected, you cannot use DAP modes and All Channel Stereo.
When the center and rear speakers Turning on or off the Surround modes
are connected (5 channels): Each time you press SURROUND ON/OFF, Surround modes turn on or off.
SPK TUNED STEREO AUTO MUTING
ON/OFF
SURROUND
Front TV Front PL II MOVIE
speaker speaker (Remote) (Front panel) or SURROUND OFF
Center speaker PL II MUSIC
Ex.: “PL II MUSIC” has been selected.
20
EN18-23.RX-5020/5022V[J]_f 20 01.12.7, 11:29 AM
Before you start, remember...
Front Panel
Display
UP UP
ANALOG SPK TUNED STEREO AUTO MUTING SLEEP
STANDBY MASTER VOLUME
DIGITAL AUTO L C R PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT VOLUME
MEMORY LINEAR PCM S.WFR LFE
DIGITAL LS S RS
DOWN DOWN
STANDBY/ON CH-
D I G I T A L
SURROUND
INPUT ATT
SOURCE NAME
PHONES
Remote Control
Using Dolby Pro Logic II, Dolby Digital
and DTS Digital Surround
Once you have adjusted the sound, the adjustment is memorized for
each source.
• When playing back digital multichannel software (Dolby Digital
5.1 ch or DTS Digital Surround), the SURROUND MODE button
CENTER +/–
TV CATV A/V CONTROL STANDBY/ON
does not work.
RECEIVER
SOUND
TEST CENTER AUDIO From the remote control:
TEST 1 2 3
EFFECT REAR L TV/CATV It will be convenient for you to use the remote control for
EFFECT 4 5 6
REAR•L +/– adjustments, since you can make adjustments from your listening
MENU REAR R VCR
7/P 8 9 point by using the test signal.
ENTER SUBWOOFER DVD REAR•R +/– • For selecting Panorama control for Pro Logic II Music, use the
10 0 10
RETURN 100 SLEEP
buttons on the front panel.
SOUND
SOUND
PTY–PTY SEARCH–PTY
REW FF
1 Setting the analog or digital input mode for the
REC PAUSE CD–DISC source you like to listen and start playing.
When playing back software encoded with Dolby Digital and
TAPE/CDR CD DVD
DTS Digital Surround, select the digital input mode (see page
ANALOG
FM/AM TV SOUND VCR /DIGITAL 11).
FM MODE
SURROUND
TV/VIDEO SURROUND
ON/OFF
MUTING
ON/OFF 2 Press SURROUND ON/OFF to ON/OFF
SURROUND
MODE activate Surround mode.
SURROUND
MODE Each time you press the button, Surround mode
VCR CH TV/CATV CH TV VOLUME turns on and off alternately.
• If you are playing back software encoded with Dolby Digital
VOLUME
multichannel, “DOLBY DIGITAL” is selected.
REMOTE CONTROL RM - SRX5020J
• If you are playing back software encoded with DTS Digital
Surround, “DTS SURROUND” is selected.
• If you are playing back any software other SURROUND
than above, you can select “PL II MUSIC” or MODE
• No test tone comes out of the rear speakers when “REAR SP” DOWN ∞ to adjust the selected
is set to “NONE.” speaker output level.
5 Adjust the speaker output levels 2
CENTER
3 3) Repeat steps 1) and 2) to adjust
(–10 to +10). the other speaker levels.
Adjust the center speaker and rear speakers levels
comparing to the sound from the front speakers. REAR L
When you select “PL II MUSIC,” you can go to the
5 6
• To adjust the center speaker level, press
following adjustment.
CENTER +/–.
• To adjust the left rear speaker level, press REAR R
REAR•L +/–. 9
• To adjust the right rear speaker level, press
8
4 Turn on Panorama control or off. Remote
NOT
REAR•R +/–. 1) Press ADJUST repeatedly until
“PANORAMA” (with the current ADJUST SETTING
Surround modes. However, no test tone is available when using the DOWN ∞ to select if you turn on
buttons on the front panel. So make adjustments while listening to or off Panorama control.
the sound of the source played back. • Each time you press the button, “ON”
and “OFF” change alternately.
1 Setting the analog or digital input mode for the
source you like to listen and start playing. ON : Select this when you like to enjoy
When playing back software encoded with Dolby Digital and “wraparound” sound effect with side-wall
DTS Digital Surround, select the digital input mode (see page image.
11). OFF : Select this when you like to enjoy
originally recorded sounds.
2 Press SURROUND ON/OFF to SURROUND ON/OFF
22
EN18-23.RX-5020/5022V[J]_f 22 01.12.7, 8:50 AM
Using DAP Modes and All Channel Stereo 2 Press SURROUND ON/OFF to SURROUND ON/OFF
The 10 keys are activated for sound adjustments. to adjust the selected speaker
output level.
5 Adjust the speakers output levels REAR L
3) Repeat steps 1) and 2) to adjust
5 6
(–10 to +10).
the other speaker level.
• To adjust the left rear speaker level, press
REAR•L +/–.
• To adjust the right rear speaker level, press
REAR R 5 For DAP modes only: Adjust the effect level.
8 9
REAR•R +/–. 1) Press ADJUST repeatedly until ADJUST SETTI
23
EN18-23.RX-5020/5022V[J]_f 23 01.12.7, 8:50 AM
COMPU LINK Remote Control System
The COMPU LINK remote control system allows you to operate Automatic Power On/Off (Standby): only possible with the
JVC’s audio components through the remote sensor on the receiver. COMPU LINK-3 and COMPU LINK-4
To use this remote control system, you need to connect JVC’s audio
Both the CD player and cassette deck (or CD recorder) turn on and
components through the COMPU LINK-4 (SYNCHRO) jacks (see
off (standby) along with the receiver.
below) in addition to the connections using cables with RCA pin
When you turn on the receiver, the CD player or cassette deck (or
plugs (see page 6).
CD recorder) will turn on automatically, depending on which
• Make sure that the AC power cords of these components are
component has been previously selected.
unplugged before connection. Plug the AC power cords only after
When you turn off the receiver, both the CD player and cassette
all connections are completed.
deck (or CD recorder) will turn off (standby).
Synchronized Recording
Cassette deck
Synchronized recording means the cassette deck starts recording as
or
soon as a CD begins playing.
CD recorder
To use synchronized recording, follow these steps:
COMPU LINK-4
(SYNCHRO) 1 Put a tape in the cassette deck and a disc in the
CD player.
2 Press the record (¶) button and the pause (8)
CD player
button on the cassette deck at the same time.
This puts the cassette deck into recording pause.
If you do not press the record (¶) button and pause (8) button at
Notes: the same time, the synchronized recording feature will not
operate.
• There are four versions of COMPU LINK remote control system.
This receiver is equipped with the fourth version—COMPU LINK-4. 3 Press the play (3) button on the CD player.
This version is added systematic operations with the CD recorder to The source changes on the receiver, and as soon as play starts,
the previous version—COMPU LINK-3.
the cassette deck starts recording. When the play ends, the
• If your audio component has two COMPU LINK jacks, you can use
either one. If it has only one COMPU LINK jack, connect it so that it
cassette deck enters recording pause, and stops about 4 seconds
is the last item in the series of components. later.
• To operate the cassette deck or CD recorder using the COMPU
LINK remote control system, set the source name correctly. Notes:
(See page 8.) • During synchronized recording, the selected source cannot be
• Refer also to the manuals supplied with your audio components. changed.
• If the power of any component is shut off during synchronized
This remote control system allows you to use four functions listed recording, the COMPU LINK remote control system may not
below. operate properly. In this case, you must start again from the
beginning.
Remote Control through the Remote Sensor on the Receiver
You can control the connected audio components through the remote
sensor on the receiver using this remote control. Aim the remote
control directly at the remote sensor on the receiver. For details, see
pages 25 to 27.
24
EN24-32.RX-5020/5022V[J]_f 24 01.12.7, 8:51 AM
Operating JVC’s Audio/Video Components
You can use the remote control to operate other JVC’s Sound Adjustment
Operating Audio Components SURROUND ON/OFF : Turn on or off the Surround modes.
SURROUND MODE : Select the Surround modes.
IMPORTANT:
To operate JVC’s audio components using this remote control:
• You need to connect JVC’s audio components through the COMPU
After pressing SOUND, you can use the following buttons for sound
LINK (SYNCHRO) jacks (see page 24) in addition to the adjustment:
connections using cables with RCA pin plugs (see page 6).
SUBWOOFER +/– : Adjust the subwoofer output level.
• Aim the remote control directly at the remote sensor on the receiver.
• If you use the buttons on the front panel, the remote control will not CENTER +/– : Adjust the center speaker output level.
operate that source. To operate a source with the remote control,
REAR•L +/– : Adjust the left rear speaker output level.
the source must be selected using source selecting buttons on the
remote control. REAR•R +/– : Adjust the right rear speaker output level.
• To operate the cassette deck or CD recorder using the COMPU EFFECT : Select the DAP effect level.
LINK remote control system, set the source name correctly. (See
page 8.) TEST : Turn on or off the test tone output.
• Refer also to the manuals supplied with your audio components.
Note:
After adjusting sounds, press the corresponding source selecting
button or CD-DISC to operate your target source by using the 10
keys; otherwise, the 10 keys cannot be used for operating your target
source.
3 : Start playback.
VOLUME
25
EN24-32.RX-5020/5022V[J]_f 25 01.12.7, 8:51 AM
Operating JVC’s Audio/Video Components
Note:
Before starting the above operations, make sure that you have
changed the source name correctly. See page 8.
26
EN24-32.RX-5020/5022V[J]_f 26 01.12.7, 8:51 AM
DVD menu operations TEST CENTER
Operating Video Components
• Some JVC’s VCRs can accept two types of the control signals— 10 0 10
RETURN 100
remote code “A” and “B.” Before using this remote control, make
sure that the remote control code of the VCR connected to the VCR
jacks is set to code “A.” MENU : Display or erase the menu screen.
• Aim the remote control directly at the remote sensor on each 5/∞
∞/3
3/2
2 : Select an item on the menu screen.
component, not on the receiver.
ENTER : Enter a selected item.
VCR
You can always perform the following operations: TV
STANDBY/ON VCR
Before operating, set TV/CATV selector to TV.
: Turn on or off a VCR. You can always perform the following operations:
VCR CH +/– : Change the TV channels on the VCR. STANDBY/ON TV/CATV
:Turn on or off a TV.
TV/VIDEO : Change the input mode (TV tuner and video
After pressing VCR (source selecting button), you can use the
input).
following buttons for VCR operations:
TV VOLUME +/– : Adjust the volume.
3 : Start playback.
TV/CATV CH +/– : Change the channels.
FF : Fast wind a tape.
REW : Rewind a tape. After pressing TV SOUND (source selecting button), you can use
7 : Stop playback or recording. the following buttons for TV operations:
8 : Pause playback. To release it, press 3. 1 – 9, 0, 100+ (+10) : Select a channel.
REC PAUSE : Press this button to enter recording pause. RETURN (10) : Function as the RETURN button.
Press this button then 3 to start recording.
DVD player
You can always perform the following operations:
STANDBY/ON DVD
:Turn on or off a DVD player.
After pressing DVD (source selecting button), you can use the
following buttons for DVD operations:
3 : Start playback.
4 : Return to the beginning of the current
(or previous) track.
¢ : Skip to the beginning of the next track.
7 : Stop playback.
8 : Pause playback. To release it, press 3.
27
EN24-32.RX-5020/5022V[J]_f 27 01.12.7, 8:51 AM
Operating Other Manufacturers’ Video Equipment
By changing the transmittable signals, you can use the remote To change the transmittable signals for
control supplied for this unit to operate other manufacturers’ operating a CATV converter
equipment.
• Refer also to the manuals supplied with the other products.
• To operate these components with the remote control, first you 1 Set TV/CATV selector to CATV.
need to set the manufacturers’ codes each for TV, CATV 2 Press and hold STANDBY/ON TV/CATV.
converter, VCR and DVD player. 3 Press TV SOUND.
• After replacing batteries of the remote control, set the 4 Enter manufacturer’s code using buttons 1–9,
manufacturers’ codes again. and 0.
5 Release STANDBY/ON TV/CATV.
Now, you can perform the following operations on the CATV
To change the transmittable signals for
converter.
operating a TV
STANDBY/ON TV/CATV
:Turn on or off the CATV converter.
1 Set TV/CATV selector to TV.
TV/CATV CH +/– : Change the channels.
2 Press and hold STANDBY/ON TV/CATV.
3 Press TV SOUND. After pressing TV SOUND (source selecting button), you can
4 Enter manufacturer’s code using buttons 1–9, use the following buttons on the CATV converter:
and 0. 1 – 10, 0, +10 (100+) :Select the channels.
5 Release STANDBY/ON TV/CATV. +10 (100+) button will be function as the
Now, you can perform the following operations on the TV. ENTER button if your equipment requires
pressing ENTER after selecting a channel
STANDBY/ON TV/CATV
number.
:Turn on or off the TV.
TV/VIDEO : Set the input mode (either TV or VIDEO). Note:
TV VOLUME +/– : Adjust the volume. Refer also to the manual supplied with your CATV converter.
TV/CATV CH +/– : Change the channels.
6 Try to operate your CATV converter by pressing
After pressing TV SOUND (source selecting button), you can STANDBY/ON TV/CATV.
use the following buttons on the TV: When your CATV converter turns on or off, you have entered
1 – 10, 0, +10 (100+) :Select the channels.
the correct code.
+10 (100+) button will be function as the
ENTER button if your TV requires pressing If there are more than one code listed for your brand of
ENTER after selecting a channel number. CATV converter, try each one until the correct one is entered.
Note:
Manufacturers’ codes for CATV converter
Refer also to the manual supplied with your TV.
Manufacturer Codes
JVC 01*
Hitachi 10
Magnavox 02
Mitsubishi 03
Panasonic 04, 11
RCA 05
Samsung 12
Sanyo 13
Sharp 06
Sony 07
Toshiba 08
Zenith 09
*Initial setting
28
EN24-32.RX-5020/5022V[J]_f 28 01.12.7, 3:56 PM
ent
To change the transmittable signals for To change the transmittable signals for
1 Press and hold STANDBY/ON VCR. 1 Press and hold STANDBY/ON DVD.
2 Press VCR. 2 Press DVD.
3 Enter manufacturer’s code using buttons 1–9, 3 Enter manufacturer’s code using buttons 1–9,
and 0. and 0.
4 Release STANDBY/ON VCR. 4 Release STANDBY/ON DVD.
Now, you can perform the following operations on the VCR. Now, you can use the following buttons on the DVD player.
STANDBY/ON VCR : Turn on or off the VCR. STANDBY/ON DVD : Turn on or off the DVD player.
VCR CH +/– : Change the channels.
After pressing DVD (source selecting button), you can use the
After pressing VCR (source selecting button), you can use the following buttons on the DVD player:
following buttons on the VCR: 3 : Start playback.
3 : Start playback. 7 : Stop playback.
FF : Fast-wind a tape. ¢ : Skip to the beginning of the next track.
REW : Rewind a tape. 4 : Return to the beginning of the current
(or previous) track.
7 : Stop playback or recording.
8 : Pause playback. To release it, press 3.
8 : Pause playback. To release it, press 3.
REC PAUSE : Press this button to enter recording DVD menu operations TEST CENTER
1 2 3
pause. After pressing DVD (source EFFECT REAR L
Press this button then 3 to start selecting button), you can use the 4 5 6
recording. following buttons for DVD menu MENU REAR R
7/P 8 9
operations: ENTER SUBWOOFER
10 0 10
Note: RETURN 100
If there are more than one code listed for your brand of 5 Try to operate your DVD player by pressing
VCR, try each one until the correct one is entered. STANDBY/ON DVD.
When your DVD player turns on or off, you have entered the
correct code.
29
EN24-32.RX-5020/5022V[J]_f 29 01.12.7, 8:51 AM
Troubleshooting
Use this chart to help you solve daily operational problems. If there is any problems you cannot solve, contact your JVC’s service center.
The power does not come on. The power cord is not plugged in. Plug the power cord into an AC outlet.
No sound from speakers. Speaker signal cables are not connected. Check speaker wiring and reconnect if
necessary.
The SPEAKERS ON/OFF button is not Press SPEAKERS ON/OFF button correctly.
set correctly.
An incorrect input mode (analog or Select the correct input mode (analog or
digital) is selected. digital).
Sound from one speaker only. Speaker signal cables are not connected Check speaker wiring and reconnect if
properly. necessary.
The balance is set to one extreme. Adjust the balance properly (see page 15).
Continuous hiss or buzzing during FM Incoming signal is too weak. Connect an outdoor FM antenna or contact
reception. your dealer.
An incorrect antenna is used. Check with your dealer to be sure you have
the correct antenna.
Occasional cracking noise during FM Ignition noise from automobiles. Move the antenna farther from automobile
reception. traffic.
“OVERLOAD” starts flashing on the Speakers are overloaded because of high 1. Press STANDBY/ON on the front
display. volume. panel to turn off the receiver.
2. Stop the playback source.
3. Turn on the receiver again, and adjust the
volume.
Speakers are overloaded because of short Press STANDBY/ON on the front panel,
circuit of speaker terminals. then check the speaker wiring.
If “OVERLOAD” does not disappear, unplug
the AC power cord, then plug it back again.
If speaker wiring is not short-circuited, contact
your dealer.
“DSP MICON NG” starts flashing on the The built-in microcomputer is not Press STANDBY/ON on the front panel to
display. functioning correctly. turn off the receiver. After unplugging the
power cord, consult your dealer.
The STANDBY lamp lights up after The receiver is overloaded because of a Press STANDBY/ON on the front panel to
turning on the power, but soon the high voltage. turn off the receiver. After unplugging the
receiver turns off (into standby mode). power cord, consult your dealer.
Remote control does not work. There is an obstruction in front of the Remove the obstruction.
remote sensor on the receiver.
Remote control does not work as you The remote control is not ready for your Press SOUND or a source selecting button
intend. intended operation. first, then press the buttons you want to use.
(See pages 25 to 27).
30
EN24-32.RX-5020/5022V[J]_f 30 01.12.7, 8:51 AM
Specifications Designs & specifications are subject to change without notice.
Amplifier
Troubleshooting / Specifications
Output Power
At Stereo operation:
Audio
Audio Input Sensitivity/Impedance (1 kHz): CD, TAPE/CDR, TV SOUND, VCR, DVD:
220 mV/47 k Ω
Audio Input (DIGITAL IN)* : Coaxial: DIGITAL 1 (DVD): 0.5 V (p-p)/75 Ω
Optical: DIGITAL 2 (CD): –21 dBm to –15 dBm (660 nm ±30 nm)
* Corresponding to Linear PCM, Dolby Digital, and DTS Digital Surround
(with sampling frequency — 32 kHz, 44.1 kHz, 48 kHz).
Audio Output Level: TAPE/CDR, VCR: 220 mV
Signal-to-Noise Ratio (’66 IHF/’78 IHF): CD, TAPE/CDR, TV SOUND, VCR, DVD: 87 dB/78 dB
Frequency Response (8 Ω): CD, TAPE/CDR, TV SOUND, VCR, DVD: 20 Hz to 20 kHz (±1 dB)
Tone Control: Bass (100 Hz): ±10 dB
Treble (10 kHz): ±10 dB
Video
Video Input Sensitivity/Impedance:
Composite video: VCR, DVD: 1 V (p-p)/75 Ω
Video Output Level/Impedance:
Composite video: VCR, MONITOR OUT: 1 V (p-p)/75 Ω
Synchronization: Negative
Signal-to-Noise Ratio: 45 dB
31
EN24-32.RX-5020/5022V[J]_f 31 01.12.7, 8:51 AM
Specifications
FM tuner (IHF)
Tuning Range: 87.5 MHz to 108.0 MHz
Usable Sensitivity: Monaural: 12.8 dBf (1.2 µV/75 Ω)
50 dB Quieting Sensitivity: Monaural: 21.3 dBf (3.2 µV/75 Ω)
Stereo: 41.3 dBf (31.5 µV/75 Ω)
Signal-to-Noise Ratio (IHF-A weighted): Monaural: 78 dB at 85 dBf
Stereo: 73 dB at 85 dBf
Total Harmonic Distortion: Monaural: 0.4% at 1 kHz
Stereo: 0.6% at 1 kHz
Stereo Separation at REC OUT: 35 dB at 1 kHz
Alternate Channel Selectivity: 45 dB: (±400 kHz)
Frequency Response: 30 Hz to 15 kHz: (+0.5 dB, –3 dB)
AM tuner
Tuning Range: 530 kHz to 1 710 kHz
Usable Sensitivity: Loop antenna: 400 µV/m
Signal-to-Noise Ratio: 50 dB (100 mV/m)
General
Power Requirements: AC 120V , 60 Hz
Power Consumption: 180 W/230 VA (at operation)
2 W (in standby mode)
Dimensions (W x H x D): 435 mm x 146.5 mm x 416 mm
(17 3/16 in. x 5 13/16 in. x 16 7/16 in.)
Mass: 8.8 kg (19.5 lbs)
32
EN24-32.RX-5020/5022V[J]_f 32 01.12.7, 8:51 AM
Authorized Service Centers
®
QUALITY SERVICE
HOW TO LOCATE YOUR JVC SERVICE CENTER
TOLL FREE: 1 (800) 537-5722
http://www.jvc.com
Dear Customer,
In order to receive the most satisfaction from your purchase, please read the instruction booklet before
operating the unit. In the event that repairs are necessary, please call 1 (800)537-5722 for your nearest
authorized servicer or visit our website at www.JVC.com
Remember to retain your Bill of Sale for Warranty Service.
Caution
To prevent electrical shock, do not open the cabinet. There are no user serviceable
parts inside. Please refer to qualified service personnel for repairs.
Accessories
To purchase accessories for your JVC product, please call toll free:1 (800)882-2345 or
on the web at www.JVC.com
BT-51002-5
(0301)
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA AND
IN COMMONWEALTH OF PUERTO RICO.
THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY, IS
LIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN.
JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT, INCONVENIENCE, LOSS OR ANY OTHER
DAMAGES, WHETHER DIRECT, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, WITHOUT LIMITATION, DAMAGE
TO TAPES, RECORDS OR DISCS) RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH
OF THIS WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANT-
ABILITY AND FITNESS FOR PARTICULAR PURPOSE, ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE.
Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an
implied warranty lasts, so these limitations or exclusions may not apply to you. This warranty gives you specific
legal rights and you may also have other rights which vary from state to state.
REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY, THIS WARRANTY DOES NOT APPLY. FOR DETAILS OF
REFURBISHED PRODUCT WARRANTY, PLEASE REFER TO THE REFURBISHED PRODUCT WARRANTY INFORMATION
PACKAGED WITH EACH REFURBISHED PRODUCT.
EN V
J C 1201NHMMDWJEIN
RX-5020VBK / RX-5022VSL
UP UP
STANDBY
PTY–PTY SEARCH–PTY MASTER VOLUME
MEMORY
DOWN DOWN
STANDBY/ON
FM MODE
INPUT ATT
SOURCE NAME
PHONES
INSTRUCTIONS
For Customer Use:
MANUAL D’INSTRUCTIONS Enter below the Model No. and Serial
No. which are located either on the rear,
bottom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
LVT0850-002A
[C]
English
Parts Identification ...................................... 2
Getting Started ........................................... 3
Before Installation ...................................................................... 3
Checking the Supplied Accessories ........................................... 3
Putting Batteries in the Remote Control .................................... 3
Connecting the FM and AM Antennas ....................................... 4
Connecting the Speakers ............................................................ 5
Connecting Audio/Video Components ....................................... 6
Connecting the Power Cord ....................................................... 7
Basic Operations ......................................... 8
Turning On the Power ................................................................ 8
Selecting the Source to Play ....................................................... 8
Adjusting the Volume ................................................................. 9
Listening Only with Headphones ............................................... 9
Turning Off the Sounds Temporarily—Muting ........................ 10
Turning Off the Power with the Sleep Timer ........................... 10
Basic Settings ........................................... 11
Setting the Digital Input (DIGITAL IN) Terminals ................. 11
Selecting the Analog or Digital Input Mode ............................ 11
Setting the Speaker Information ............................................... 12
Sound Adjustments .................................... 15
Attenuating the Input Signal .................................................... 15
Adjusting the Front Speakers Output Balance ......................... 15
Adjusting the Tone ................................................................... 15
Adjusting the Subwoofer Output Level .................................... 15
Tuner Operations ....................................... 16
Tuning in Stations Manually .................................................... 16
Using Preset Tuning ................................................................. 16
Selecting the FM Reception Mode ........................................... 17
Creating Realistic Sound Fields ................... 18
About Relations between Speaker Layout and
Surround Modes ................................................................. 20
Using Dolby Pro Logic II, Dolby Digital and
DTS Digital Surround ........................................................ 21
Using DAP Modes and All Channel Stereo ............................. 23
COMPU LINK Remote Control System ......... 24
Operating JVC's Audio/Video
Components .......................................... 25
Operating Audio Components .................................................. 25
Operating Video Components .................................................. 27
Operating Other Manufacturers' Video
Equipment ............................................ 28
Troubleshooting ......................................... 30
Specifications ............................................ 31
1
EN01-07.RX-5020/5022V[C]_f 1 01.12.27, 10:09 AM
Parts Identification
English
Front Panel
1 2 3 45 6 7 89 p
UP UP
ANALOG SPK TUNED STEREO AUTO MUTING SLEEP
STANDBY
DIGITAL AUTO L C R PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT VOLUME
MEMORY LINEAR PCM S.WFR LFE
LS S RS
MASTER VOLUME
DOWN DOWN DIGITAL
STANDBY/ON CH-
INPUT ATT
SOURCE NAME
PHONES
q w e r t y u i o
5 e Remote Control
TAPE/CDR CD DVD 1 TV/CATV selector (27, 28)
2 • 10 keys for selecting preset channels (17)
6 FM/AM TV SOUND VCR
ANALOG
/DIGITAL • 10 keys for adjusting sound (15, 22, 23)
r • 10 keys for operating audio/video components (25 – 29)
FM MODE 3 SOUND button (15, 22, 23)
7 4 Operating buttons for audio/video components
ON/OFF
t (25 – 27, 29)
TV/VIDEO SURROUND MUTING
8 MODE y 5 REC PAUSE button (26, 27, 29)
6 Source selecting buttons (8, 9, 11, 17, 25 – 29)
9 u TAPE/CDR, CD, DVD, FM/AM, TV SOUND, VCR
7 FM MODE button (17)
p VCR CH TV/CATV CH TV VOLUME i 8 TV/VIDEO button (27, 28)
9 TV/CATV CH (channel) +/– buttons (27, 28)
VOLUME
p VCR CH (channel) +/– buttons (27, 29)
q STANDBY/ON buttons (8, 27 – 29)
REMOTE CONTROL RM - SRX5020J
AUDIO, TV/CATV, VCR, DVD
w SLEEP button (10)
e CD–DISC button (26)
r ANALOG/DIGITAL button (11, 12)
t SURROUND ON/OFF and SURROUND MODE buttons
(20, 21, 23, 25)
y MUTING button (10)
u TV VOLUME +/– buttons (27, 28)
i VOLUME +/– button (9)
2
EN01-07.RX-5020/5022V[C]_f 2 02.1.9, 4:37 PM
Getting Started
English
Before Installation Putting Batteries in the Remote Control
General Precautions Before using the remote control, put two supplied batteries first.
• DO NOT insert any metal object into the unit. • When using the remote control, aim the remote control directly at
• DO NOT disassemble the unit or remove screws, covers, or the remote sensor on the unit.
cabinet.
• DO NOT expose the unit to rain or moisture. 1 On the back of the remote control, remove the
battery cover.
Locations
• Install the unit in a location that is level and protected from
moisture.
• The temperature around the unit must be between –5˚C and 35˚C
(23˚F and 95˚F).
• Make sure there is good ventilation around the unit. Poor
ventilation could cause overheating and damage the unit.
• Batteries (2)
• FM Antenna (1)
CAUTION:
Follow these precautions to avoid leaking or cracking cells:
• Place batteries in the remote control so they match the polarity:
(+) to (+) and (–) to (–).
• Use the correct type of batteries. Batteries that look similar may
differ in voltage.
• Always replace both batteries at the same time.
• Do not expose batteries to heat or flame.
3
EN01-07.RX-5020/5022V[C]_f 3 01.12.27, 10:10 AM
Getting Started
English
75
or
FMAXIAL 75
FMAXIAL
CO CO
FM antenna (supplied)
Snap the tabs on the loop Extend the supplied FM antenna horizontally.
into the slots of the base
to assemble the AM loop
antenna.
AM
LOOP
AM
EXT
NT
FROKERS
EA FT
SP T LE +
RIGH
CE
N: DAN
R
REA RS
– TIO IMPE
NA + CAU KER
TEN FM 75IAL EAKE + SPEA16
1 2 3
AN SP LEFT
TER
AX
CO T 8
CEN KER RIGH
SP
EA –
–
K-4 +
LIN O)
MPU R
CO(SYNCH
OR
–
NIT
MOOUT AM
AM
OP EXIT
LO
1
ITAL ) LEFT DVD
DIG(DVD T
RIGH
CD T
OU )
(REC
) OUT DVD VC
R
CD )
2( (REC AU
DIO INY)
ITAL TAPE (PLA O
DIG R VIDE
/CD
INY)
(PLA
IN
ITAL
DIG T
OU )
(REC
R
VC
INY) FER
OO
(PLA BW
SU OUT
FT
LE
D
UN T
SO RIGH DIO
TV AU
AM antenna connection
Connect the AM loop antenna supplied to the AM LOOP
terminals.
Turn the loop until you have the best reception.
• If the reception is poor, connect an outdoor single vinyl-
covered wire (not supplied) to the AM EXT terminal. (Keep the
AM loop antenna connected.)
4
EN01-07.RX-5020/5022V[C]_f 4 01.12.27, 10:10 AM
English
Connecting the Speakers Speaker layout diagram
After connecting the front, center, rear speakers and/or a subwoofer, “YES” for the subwoofer and “SMALL” for the front, center
set the speaker setting information properly to obtain the best and rear speakers are initial settings. To get best possible
possible Surround effect. For details, see pages 12 to 14. sound, change the subwoofer and speaker settings to fit your
listening conditions (See pages 12 and 13).
CAUTION:
Use speakers with the SPEAKER IMPEDANCE indicated by the
speaker terminals.
Center
Connecting the front, center and rear speakers speaker
STANDBY
MASTER VOLUME
1
MEMORY
STANDBY/ON D I G I T A L
SURROUND
SURROUND ON/OFF
INPUT ANALOG INPUT DIGITAL ADJUST SETTING
CONTROL
SURROUND MODE SPEAKERS ON/OFF DOWN UP
CD TAPE/CDR FM/AM
SOURCE NAME
PHONES
REARERS
– ION IMP
NA 75 + CAUT ER
AN
TEN FM XIAL EAK
SP LEFT + SPEAK
16
COA TER HT 8
CEN ER RIG
SP
EAK –
–
K-4 +
U LIN O)
MP HR
CO(SYNC
OR
–
NIT AM
MOOUT AMP
EXIT
LOO
L1 T D
ITA LEF
DIG(DVD) DV
HT
RIG
CD T
OUC)
(RE
Powered subwoofer BW
OO
FER
SU OUT
To
subwoofer
SUBWOOFER
OUT
NT
FROKERS
EA FT +
SP T LE
H
RIG
Connect the input jack of a powered subwoofer to the N : ED
AN
CE
R
REAERS
– TIO IMP
SUBWOOFER OUT jack on the rear panel, using a cable with RCA EAK
SP LEFT +
+ CAUAKER
E
SP 16
To left
TER HT front speaker
pin plugs (not supplied). CEN KER
EA
RIG 8
SP –
• Refer also to the manual supplied with your subwoofer. –
+
5
EN01-07.RX-5020/5022V[C]_f 5 01.12.27, 10:10 AM
Getting Started
English
Cassette deck
Turn off all components before connections.
To audio input PHONO To audio output
You can connect the following audio/video components to this
receiver. Refer also to the manuals supplied with your components. CD
TV SOUND
TV
TV CD
RIGHT LEFT
AUDIO OUT MONITOR
(REC) OUT
TAPE
CDR
IN DVD
(PLAY)
VIDEO
TV SOUND
RIGHT LEFT
AUDIO
To video input
6
EN01-07.RX-5020/5022V[C]_f 6 01.12.27, 10:10 AM
English
VCR IMPORTANT:
• When connecting the DVD player or digital TV using the digital
A VCR C terminal, you also need to connect it to the video jack on the rear.
Without connecting it to the video jack, you can view no playback
picture.
• After connecting the components using the DIGITAL IN terminals,
B D set the followings correctly if necessary:
– Set the digital input (DIGITAL IN) terminal setting correctly. For
details, see “Setting the Digital Input (DIGITAL IN) Terminals” on
CD page 11.
– Select the digital input mode correctly. For details, see “Selecting
OUT MONITOR the Analog or Digital Input Mode” on page 11.
(REC) OUT
TAPE
CDR
IN DVD
(PLAY) Digital TV
OUT OUT
(REC) (REC)
DVD player
VCR VCR
IN IN
(PLAY) (PLAY)
VIDEO
TV SOUND
DVD
protective plug.
DVD
AUDIO
OUT
(REC)
VCR
IN
(PLAY) Notes:
VIDEO • When shipped from the factory, the DIGITAL IN terminals have
Å To front left/right channel audio output (or to audio mixed been set for use with the following components.
– DIGITAL 1 (coaxial): For DVD player
output)
– DIGITAL 2 (optical): For CD player
ı To video output
• When you want to operate the CD player or CD recorder using the
COMPU LINK remote control system, connect the target
component also as described in “Analog connections” (see page 6).
Note:
To enjoy the software encoded with Dolby Digital or DTS Digital
Surround, you must connect the DVD player using the digital terminal Connecting the Power Cord
on the rear of this receiver. (See “Digital connections” below.)
Before plugging the power cord into an AC outlet, make sure that all
connections have been made.
Digital connections Plug the power cord into an AC outlet.
This receiver is equipped with two DIGITAL IN terminals—one
CAUTIONS:
digital coaxial terminal and one digital optical terminal.
You can connect any component to one of the digital terminals using • Do not touch the power cord with wet hands.
• Do not pull on the power cord to unplug the cord. When
a digital coaxial cable (not supplied) or digital optical cable (not
unplugging the cord, always grasp the plug so as not to damage
supplied).
the cord.
7
EN01-07.RX-5020/5022V[C]_f 7 01.12.27, 10:10 AM
Basic Operations
English
TEST
1
EFFECT
2
CENTER
REAR L
3
AUDIO
STANDBY/
ON
TV/CATV
4 5 6
AUDIO/VIDEO CONTROL RECEIVER MENU REAR R VCR
STANDBY/ON
DOWN DOWN DIGITAL LS S RS
CH-
SOUND
PTY–PTY SEARCH–PTY
REW FF
SLEEP
REC PAUSE CD–DISC
DVD VCR TV SOUND
SURROUND ON/OFF
INPUT ANALOG
INPUT ATT
INPUT DIGITAL ADJUST SETTING
Source TAPE/CDR CD DVD
SOURCE NAME
buttons FM MODE
ON/OFF
CH-
The STANDBY lamp on the front panel lights up. 1 Press TAPE/CDR (SOURCE NAME). TAPE/CDR
A small amount of power is consumed in standby mode. To turn the 2 Press and hold SOURCE NAME
power off completely, unplug the AC power cord.
(TAPE/CDR) until “ASSIGN CDR” appears on the display.
TAPE/CDR CD DVD
Without changing the source name, you can still use the connected
component. However, there may be some inconvenience.
CD TAPE/CDR FM/AM
FM/AM TV SOUND VCR – “TAPE” will appear on the display when you select the CD
recorder.
SOURCE NAME – You cannot use the digital input (see page 11) for the CD recorder.
– You cannot use the COMPU LINK remote control system (see page
On the front panel From the remote control 24) to operate the CD recorder.
8
EN08-17.RX-5020/5022V[C]_f 8 01.12.27, 10:11 AM
English
Selecting different sources for picture and Listening Only with Headphones
sound
You can watch picture from a video component while listening to You must turn off the speakers when you listen with headphones.
sound from another component.
1 Connect a pair of headphones to the PHONES jack on the front
Press one of the audio source selecting buttons (CD, TAPE/CDR, panel.
FM/AM), while viewing the picture from a video component such as
the VCR or DVD player, etc. 2 Press SPEAKERS ON/OFF.
DVD VCR TV SOUND TAPE/CDR CD DVD
• “HEADPHONE” appears for a while and the H. PHONE
indicator lights up on the display.
FM/AM TV SOUND VCR
CD TAPE/CDR FM/AM The H. PHONE indicator lights up.
ANALOG
SOURCE NAME L R H.PHONE
Note: This cancels the Surround mode currently selected, and activates
Once you have selected a video source, pictures of the selected the HEADPHONE mode.
source are sent to the TV until you select another video source.
Note:
The volume level can be adjusted within the range of “0” (minimum) to
“50” (maximum).
9
EN08-17.RX-5020/5022V[C]_f 9 01.12.27, 10:11 AM
Basic Operations
English
CH-
• Subwoofer output level (see page 15)
• Surround mode selection (see pages 21 – 23 )
Notes:
• You cannot assign and store different settings for digital input
To restore the sound, press MUTING again. mode and analog input mode.
• Turning MASTER VOLUME on the front panel or pressing • If the source is FM or AM, you can assign a different setting for
VOLUME +/– on the remote control also restores the sound. each band.
For recording
You can record any sources playing through the receiver to a
Turning Off the Power Remote cassette deck (or a CD recorder) connected to the TAPE/CDR
with the Sleep Timer ONLY jacks and the VCR connected to the VCR jacks at the same time.
You can fall asleep while listening to music—Sleep Timer. While recording, you can listen to the selected sound source at
whatever sound level you like without affecting the sound levels
Press SLEEP on the remote control repeatedly. SLEEP of the recording.
• The SLEEP indicator lights up on the display, and the
shut-off time changes in 10 minutes intervals. Note:
The output volume level, tone adjustment (see page 15), and
ANALOG SPK
L C R
SLEEP Surround modes (see page 18) cannot affect the recording.
S.WFR LFE
LS S RS
0 (Canceled) 90 80 70 L C R ANALOG
DIGITAL AUTO
SPK
L C R
ONETOUCH
PRO LOGIC ΙΙ L C R
LINEAR PCM S.WFR LFE
DIGITAL LS S RS
S.WFR LFE CH- S.WFR LFE
LS S RS LS S RS
When the shut-off time comes
The receiver turns off automatically. The following signal indicators light up—:
L : •When digital input is selected: Lights up when the left
To check or change the time remaining until the shut-off time channel signal comes in.
Press SLEEP once. • When analog input is selected: Always lights up.
The remaining time (in minutes) until the shut-off time appears. R : • When digital input is selected: Lights up when the right
• To change the shut-off time, press SLEEP repeatedly. channel signal comes in.
• When analog input is selected: Always lights up.
To cancel the Sleep Timer C : When the center channel signal comes in.
Press SLEEP repeatedly until “SLEEP 0 MIN” appears on the LS : When the left rear channel signal comes in.
display. (The SLEEP indicator goes off.) RS : When the right rear channel signal comes in.
• Turning off the power also cancels the Sleep Timer. S : When the monaural rear channel signal or 2 channel Dolby
Surround encoded signal comes in.
LFE: When the LFE channel signal comes in.
Note:
When “SUBWOOFER” is set to “YES” (see page 12), S.WFR lights
up.
10
EN08-17.RX-5020/5022V[C]_f 10 01.12.27, 10:11 AM
Basic Settings
English
Front Panel Remote Control
UP UP
ENTER SUBWOOFER DVD
ANALOG SPK TUNED STEREO AUTO MUTING SLEEP
STANDBY
DIGITAL AUTO L C R PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT VOLUME MASTER VOLUME 10 0 10
MEMORY LINEAR PCM S.WFR LFE
RETURN 100 SLEEP
DIGITAL LS S RS
DOWN DOWN
CH- SOUND
STANDBY/ON
PTY–PTY SEARCH–PTY
REW FF
INPUT ATT
INPUT DIGITAL ADJUST SETTING
VOLUME
Setting the Digital Input Remote Selecting the Analog or Digital Input
[DIGITAL IN] Terminals NOT Mode
When you use the digital input terminals, register what components When you have connected digital source components using both the
are connected to which terminals (DIGITAL 1/2) so that the correct analog connection (see page 6) and the digital connection (see page
source name will appear when you select the digital source. 7) methods, you need to select the input mode correctly.
Before you start, remember...
There is a time limit in doing the following steps. If the setting is 1 Press one of the source selecting buttons—DVD,
canceled before you finish, start from step 1 again. TV SOUND, CD, or TAPE/CDR*—for which you
want to change the input mode.
1 Press SETTING repeatedly until SETTING DVD VCR TV SOUND
TAPE/CDR CD DVD
S.WFR LFE
LS S RS
Note:
DIGITAL 1 terminal setting
* Among the sources listed above, you can select the digital input
* “1DVD 2CD” is the initial setting. If you have already only for the sources which you have selected the digital input
changed the setting, another combination will be shown. terminals for. (See “Setting the Digital Input (DIGITAL IN)
Terminals.”)
• Each time you press the button, the display “DIGITAL AUTO” appears on the display
changes to show the following: and the indicator for the detected signals also
lights up.
1 DVD 2 CD j 1 DVD 2 TV j 1 DVD 2 CDR j
1 CD 2 DVD j 1 CD 2 TV j 1 CD 2 CDR j To change the input mode back to analog INPUT ANALOG
as the digital input for the following components. • Each time you press the button, the input mode
– DIGITAL 1 (coaxial): For DVD player alternates between the analog input (“ANALOG”)
– DIGITAL 2 (optical): For CD player and the digital input (“DIGITAL AUTO”).
Remote
DIGITAL AUTO : Select this for the digital input mode. The Setting the Speaker Information NOT
receiver automatically detects the
incoming signal format. (The DIGITAL To obtain the best possible sound or effect from the Surround modes
AUTO indicator lights up on the display, (see page 18), register the following speakers and subwoofer
then the digital signal indicator for the information after all connections are completed.
detected signals lights up.)
ANALOG : Select this for the analog input mode. The followings are items you can set:
(Initial setting when shipped from the • Subwoofer information—SUBWOOFER
factory.) • Speaker size—FRNT SP, CNTR SP, REAR SP
• Speaker distance—UNIT, FRNT DIS, CNTR DIS, REAR DIS
If the following symptoms occur while playing Dolby Digital or • Crossover frequency—CROSS
DTS Digital Surround software with “DIGITAL AUTO” • Low frequency effect attenuator—LFE ATT
selected, follow the procedure below. • Dynamic range compression—D. COMP
• Sound does not come out at the beginning of playback.
• Noise comes out while searching or skipping chapters or tracks.
1 Press INPUT DIGITAL (or ANALOG/DIGITAL on the remote Before you start, remember...
control). There is a time limit in doing the following steps. If the setting is
• “DIGITAL AUTO” appears on the display. canceled before you finish, start from step 1 again.
CH-
• To play back software encoded with Dolby Digital, select 2 Press CONTROL UP 5/DOWN ∞ to CONTROL
DOWN UP
Note:
When “DIGITAL AUTO” cannot recognize the incoming signals, no
digital signal indicators light up on the display.
12
EN08-17.RX-5020/5022V[C]_f 12 01.12.27, 10:11 AM
English
Speaker size Speaker distance
Register the sizes of all the connected speakers. Register the unit you use, then the speaker distance from your
• When you change your speakers, register the information about listening point.
the speakers again. • If you have set the unit before, start from step 3.
1 Press SETTING repeatedly until T SETTING 1 Press SETTING repeatedly until SETTING
LARGE : Select this when the speaker size is relatively large. “FRNT DIS (Front distance),” “CNTR
(See “Notes” below.) DIS (Center distance)” or “REAR DIS
SMALL : Select this when the speaker size is relatively small. (Rear distance)” (with the current setting)*
(See “Notes” below.) appears on the display.
NONE : Select this when you have not connected a speaker. The display shows the current setting in the unit selected in step 2.
(Not selectable for the front speakers) * “3.0m” is the initial setting for meter and “10FT” is for feet. If
you have already changed the setting, another value will be
shown.
3 Repeat steps 1 and 2 to select the appropriate
items for other speakers. 4 Press CONTROL UP 5/DOWN ∞ to CONTROL
DOWN UP
Note:
If you have selected “NONE” for the center and rear speakers
setting, you cannot set the speaker distance for the center and
rear speakers.
13
EN08-17.RX-5020/5022V[C]_f 13 01.12.27, 10:11 AM
Basic Settings
English
not take effect (“CROSS OFF” appears). ATT (Low Frequency Effect
Attenuator)” (with the current setting)*
1 Press SETTING repeatedly until SETTING
appears on the display.
“CROSS (Crossover)” (with the current * “0dB” is the initial setting. If you have already changed the
setting)* appears on the display. setting, “–10dB” will be shown.
* “150HZ” is the initial setting. If you have already changed the
setting, another frequency will be shown. 2 Press CONTROL UP 5/DOWN ∞ to CONTROL
DOWN UP
200HZ 150HZ
Note:
Crossover frequency is not valid for the HEADPHONE mode. Dynamic range compression
You can compress the dynamic range (difference between maximum
sound and minimum sound) of the reproduced sound. This is useful
when enjoying surround sound at night.
• This function takes effect only when playing back a source using
Dolby Digital.
OFF MID
MAX
OFF : Select this when you want to enjoy surround with its
full dynamic range. (No effect applied.)
MID : Select this when you want to reduce the dynamic range
a little.
MAX : Select this when you want to apply the compression
effect fully. (Useful at night.)
14
EN08-17.RX-5020/5022V[C]_f 14 01.12.27, 10:11 AM
Sound Adjustments
English
Front Panel Remote Control
Display TV CATV A/V CONTROL
RECEIVER
STANDBY/ON
10
SUBWOOFER
0 10
DVD
SOUND
STANDBY MASTER VOLUME
DIGITAL AUTO L C R PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT VOLUME
MEMORY LINEAR PCM S.WFR LFE
PTY–PTY SEARCH–PTY
REW FF
DIGITAL LS S RS
DOWN DOWN
STANDBY/ON CH-
REC PAUSE CD–DISC
SOURCE NAME
PHONES
VCR CH TV/CATV CH TV VOLUME
VOLUME
indicator lights up on the display. adjust the bass or treble sounds level.
• Each time you press and hold the button, the Input Attenuator • Each time you press the button, the sound
mode turns on (“INPUT ATT ON”) or off (“INPUT level changes by ±2 steps.
NORMAL”).
Adjusting the Subwoofer Output Level
Adjusting the Front Speakers Remote
Output Balance NOT You can adjust the subwoofer output level if you have connected a
subwoofer and set the subwoofer information correctly—“YES.”
If the sounds you hear from the front right and left speakers are
On the front panel:
unequal, you can adjust the speakers output balance.
Before you start, remember...
Before you start, remember... There is a time limit in doing the following steps. If the setting is
There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
canceled before you finish, start from step 1 again.
1 Press ADJUST repeatedly until ADJUST SETTIN
15
EN08-17.RX-5020/5022V[C]_f 15 01.12.27, 10:12 AM
Tuner Operations
English
4 5
REAR L
6
TV/CATV
10 keys MENU
7/P 8
REAR R
9
VCR
PTY–PTY SEARCH–PTY
REW FF
FM/AM TUNING FM/AM PRESET FM MODE
UP UP
ANALOG SPK TUNED STEREO AUTO MUTING SLEEP
STANDBY MASTER VOLUME
DIGITAL AUTO L C R PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT VOLUME REC PAUSE CD–DISC
MEMORY LINEAR PCM S.WFR LFE
DIGITAL LS S RS
DOWN DOWN
STANDBY/ON CH-
TAPE/CDR CD DVD
ANALOG
FM/AM TV SOUND VCR /DIGITAL
SURROUND ON/OFF
INPUT ANALOG INPUT DIGITAL
DVD VCR TV SOUND
ADJUST SETTING
FM/AM FM MODE
ON/OFF
FM MODE
INPUT ATT
SOURCE NAME
VCR CH TV/CATV CH TV VOLUME
PHONES
VOLUME
MEMORY FM/AM
1 Press FM/AM to select the band Once a station is assigned to a channel number, the station can be
(FM or AM). quickly tuned. You can preset up to 30 FM and 15 AM stations.
The last received station of the selected band is tuned in.
To store the preset stations
FM/AM Remote
FM/AM
NOT
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
On the front panel From the remote control canceled before you finish, start from step 2 again.
CH-
LS S RS
CH-
CH-
Notes:
• When you press and hold FM/AM TUNING UP/DOWN in step 2, 3 Press FM/AM PRESET UP/ FM/AM PRESET
UP
the frequency keeps changing until a station is tuned in.
• When a station of sufficient signal strength is tuned in, the TUNED
DOWN to select a channel number
indicator lights up on the display. while the channel number position DOWN
CH-
16
EN08-17.RX-5020/5022V[C]_f 16 01.12.27, 10:12 AM
English
4 Press MEMORY again while the MEMORY
Selecting the FM Reception Mode
selected channel number is flashing
on the display. When an FM stereo broadcast is hard to receive or noisy, you can
The selected channel number stops flashing. change the FM reception mode while receiving an FM broadcast.
The station is assigned to the selected channel number. • You can store the FM reception mode for each preset station (see
page 16).
ANALOG SPK TUNED STEREO AUTO MUTING
L C R VOLUME
S.WFR LFE
LS S RS
CH-
1 While listening to an FM station, press FM
MODE.
• Each time you press the button, the FM reception mode
5 Repeat steps 1 to 4 until you store all the stations alternates between “AUTO” and “MONO.”
you want.
FM MODE FM MODE
S.WFR LFE
CH-
(FM or AM).
The last received station of the selected band
ANALOG SPK TUNED
is tuned in. L C
S.WFR LFE
R
CH-
UP
hear monaural sounds. This mode is also useful to
suppress static noise between stations. The AUTO
until you find the channel you want. MUTING indicator lights up on the display.
• Pressing FM/AM PRESET UP increases (Initial setting)
DOWN
the channel numbers.
• Pressing FM/AM PRESET DOWN MONO : Select this to improve the reception (but stereo
decreases the channel numbers. effect will be lost).
In this mode, you will hear noise while tuning into
the stations. The AUTO MUTING indicator goes
From the remote control: off from the display. (The STEREO indicator also
goes off.)
1 Press FM/AM to select the band (FM or FM/AM
AM).
The last received station of the selected band is To restore the stereo effect
tuned in and the10 keys now work for tuner operation. Select “AUTO” in step 1.
• Each time you press the button, the band
alternates between FM and AM.
4 5 6
• For channel number 5, press 5. MENU REAR R
• For channel number 15, press +10 then 5. 7/P 8 9
• For channel number 20, press +10 then 10. ENTER SUBWOOFER
10 0 10
• For channel number 30, press +10, +10, RETURN 100
then 10.
17
EN08-17.RX-5020/5022V[C]_f 17 01.12.27, 10:12 AM
Creating Realistic Sound Fields
English
You can use the following Surround modes to reproduce a realistic Dolby Digital*
sound field: Used to reproduce multichannel sound tracks of the software
■ Dolby Surround encoded with Dolby Digital ( ). D I G I T A L
• Dolby Pro Logic II • To enjoy the software encoded with Dolby Digital, connect the
• Dolby Digital source component using the digital terminal on the rear of this
■ DTS Digital Surround receiver. (See page 7.)
■ DAP (Digital Acoustic Processor) modes
■ All Channel Stereo Dolby Digital 5.1 ch encoding method (so-called discrete
multichannel digital audio format) records and digitally compresses
the left front channel, right front channel, center channel, left rear
■ Dolby Surround channel, right rear channel, and LFE channel signals.
Since each channel is completely independent from the other
Dolby Pro Logic II*
channel signals to avoid interference, you can obtain much better
Dolby Pro Logic II has a newly developed multichannel playback sound quality with much stereo and surround effects.
format to decode all 2 channel sources—regular stereo source and
Dolby Surround encoded source—into 5.1 channel. Note:
Matrix-based encoding/decoding method for Dolby Pro Logic II Dolby Digital software can be roughly grouped into two categories
makes no limitation for the cutoff frequency of the rear treble and —multichannel (up to “5.1” channel) and 2 channel software. To enjoy
enables stereo rear sound compared to conventional Dolby Pro surround sounds while playing Dolby Digital 2 ch software, you can
Logic. use Dolby Pro Logic II.
Dolby Pro Logic II enables to reproduce spacious sound from
original sound without adding any new sounds and tonal colorations.
Dolby Pro Logic II has two modes—Movie mode and Music mode:
■ DTS Digital Surround**
Pro Logic II Movie (PL II MOVIE)—suitable for reproduction of Used to reproduce multichannel sound tracks of the software
Dolby Surround encoded sources bearing the mark DOLBY SURROUND .
encoded with DTS Digital Surround ( ).
You can enjoy soundfield very close to the one created with discrete • To enjoy the software encoded with DTS Digital Surround,
5.1 channel sounds. connect the source component using the digital terminal on the
Pro Logic II Music (PL II MUSIC)—suitable for reproduction of rear of this receiver. (See page 7.)
any 2 channel stereo music sources. You can enjoy wide and deep
sound by using this mode. For this mode, Panorama control can be DTS Digital Surround is another discrete multichannel digital
selected, which gives “wraparound” sound effect with side-wall audio format available on CD, LD, and DVD software.
image. Compared to Dolby Digital, audio compression ratio is relatively
• When Dolby Pro Logic II is activated, PRO LOGIC II low. This fact allows DTS Digital Surround format to add breadth
indicator lights up on the display. and depth to the reproduced sounds. As a result, DTS Digital
Surround features natural, solid and clear sound.
Center
speaker
STANDBY
MASTER VOLUME
MEMORY
STANDBY/ON D I G I T A L
SURROUND
CONTROL
SURROUND MODE SPEAKERS ON/OFF DOWN UP
CD TAPE/CDR FM/AM
SOURCE NAME
PHONES
* Manufactured under license from Dolby Laboratories. “Dolby,” “Pro ** Manufactured underlicense from Digital Theater Systems, Inc. US
Logic,” and the double-D symbol are trademarks of Dolby PAT. No. 5,451,942 and other world-wide patents issued and
Laboratories. Confidential unpublished works. ©1992–1997 Dolby pending. “DTS” and “DTS Digital Surround” are trademarks of
Laboratories, Inc. All rights reserved. Digital Theater Systems, Inc. Copyright 1996 Digital Theater
Systems, Inc. All rights reserved.
18
EN18-23.RX-5020/5022V[C]_f 18 01.12.27, 10:12 AM
English
■ DAP (Digital Acoustic Processor) modes ■ All Channel Stereo
DAP modes have been designed to create important acoustic This mode can reproduce a larger stereo sound field using all the
surround elements. connected (and activated) speakers.
The sound heard in a live club, dance club, hall or pavilion consists All Channel Stereo can be used when the front and rear
of direct sound and indirect sound—early reflections and reflections speakers are connected to this receiver without respect to the
from behind. Direct sounds reach the listener directly without any center speaker connection.
reflection. On the other hand, indirect sounds are delayed by the If the center speaker is connected and activated, the same phase of
distances of the ceiling and walls (see the diagram below). the front left and right signals are output through the center speaker.
These indirect sounds are important elements of the acoustic
All Channel Stereo can be used while reproducing 2 channel stereo
surround effects. The DAP mode can reproduce a realistic sound
software, either analog or digital except Dolby Digital and DTS
field by adding these indirect sounds.
Digital Surround.
DAP modes can be used when the front and rear speakers are • When All Channel Stereo is selected, the DSP indicator lights up
connected to this receiver (without respect to the center speaker on the display.
connection: no sound comes out of the center speaker even if it is
connected).
All Channel Stereo reproduction
The following DAP modes are provided with this receiver:
LIVE CLUB : Gives the feeling of a live music club with a low
ceiling.
DANCE CLUB : Gives a throbbing bass beat.
HALL : Gives clear vocal and the feeling of a concert
hall.
PAVILION : Gives the spacious feeling of a pavilion with a
high ceiling.
These DAP modes can be used to add the acoustic surround effects
while reproducing 2 channel stereo software—either analog or
digital except Dolby Digital and DTS Digital Surround—and can Sound reproduced from normal stereo
give you a real “being there” feeling.
• When one of the DAP modes is selected, the DSP indicator lights
up on the display.
Linear PCM 䡬 ⳯ ⳯ 䡬 䡬 䡬 䡬 䡬 䡬 䡬
Analog 䡬 ⳯ ⳯ 䡬 䡬 䡬 䡬 䡬 䡬 䡬
19
EN18-23.RX-5020/5022V[C]_f 19 01.12.27, 10:12 AM
Creating Realistic Sound Fields
English
Available Surround modes will vary depending on how many speakers are used with this receiver.
Make sure that you have set the speaker information correctly (see pages 12 to 14).
• If only front speakers are connected, you cannot use Surround modes.
• If rear speakers are not connected, you cannot use DAP modes and All Channel Stereo.
When the center and rear speakers Turning on or off the Surround modes
are connected (5 channels): Each time you press SURROUND ON/OFF, Surround modes turn on or off.
SPK TUNED STEREO AUTO MUTING
When the center speaker is connected Turning on or off the Surround modes
(3 channels):
Each time you press SURROUND ON/OFF, Surround modes turn on or off.
SPK TUNED STEREO AUTO MUTING
DIGITAL AUTO L R PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
LINEAR PCM S.WFR
SURROUND ON/OFF
ON/OFF
SURROUND
Front TV Front PL II MOVIE
speaker speaker (Remote) (Front panel) or SURROUND OFF
Center speaker PL II MUSIC
Ex.: “PL II MUSIC” has been selected.
20
EN18-23.RX-5020/5022V[C]_f 20 01.12.27, 10:12 AM
English
Before you start, remember...
• Make sure that you have set the speaker information correctly (see pages 12 to 14).
• You cannot adjust the center speaker output level when you have set “CNTR SP” to “NONE.”
• You cannot adjust the rear speaker output levels when you have set “REAR SP” to “NONE.”
• Remember not to change the speaker setting while using any Surround modes; otherwise, it may be canceled when you deactivate the
speakers required for the Surround mode.
Front Panel
Display
UP UP
ANALOG SPK TUNED STEREO AUTO MUTING SLEEP
STANDBY MASTER VOLUME
DIGITAL AUTO L C R PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT VOLUME
MEMORY LINEAR PCM S.WFR LFE
DIGITAL LS S RS
DOWN DOWN
STANDBY/ON CH-
INPUT ATT
SOURCE NAME
PHONES
Remote Control
Using Dolby Pro Logic II, Dolby Digital
and DTS Digital Surround
Once you have adjusted the sound, the adjustment is memorized for
each source.
• When playing back digital multichannel software (Dolby Digital
5.1 ch or DTS Digital Surround), the SURROUND MODE button
CENTER +/–
TV CATV A/V CONTROL STANDBY/ON
does not work.
RECEIVER
SOUND
TEST CENTER AUDIO From the remote control:
TEST 1 2 3
EFFECT REAR L TV/CATV It will be convenient for you to use the remote control for
EFFECT 4 5 6
REAR•L +/– adjustments, since you can make adjustments from your listening
MENU REAR R VCR
7/P 8 9 point by using the test signal.
ENTER SUBWOOFER DVD REAR•R +/– • For selecting Panorama control for Pro Logic II Music, use the
10 0 10
RETURN 100 SLEEP
buttons on the front panel.
SOUND
SOUND
PTY–PTY SEARCH–PTY
REW FF
1 Setting the analog or digital input mode for the
REC PAUSE CD–DISC source you like to listen and start playing.
When playing back software encoded with Dolby Digital and
TAPE/CDR CD DVD
DTS Digital Surround, select the digital input mode (see page
ANALOG
FM/AM TV SOUND VCR /DIGITAL 11).
FM MODE
SURROUND
TV/VIDEO SURROUND
ON/OFF
MUTING
ON/OFF 2 Press SURROUND ON/OFF to ON/OFF
SURROUND
MODE activate Surround mode.
SURROUND
MODE Each time you press the button, Surround mode
VCR CH TV/CATV CH TV VOLUME turns on and off alternately.
• If you are playing back software encoded with Dolby Digital
VOLUME
multichannel, “DOLBY DIGITAL” is selected.
REMOTE CONTROL RM - SRX5020J
• If you are playing back software encoded with DTS Digital
Surround, “DTS SURROUND” is selected.
• If you are playing back any software other SURROUND
than above, you can select “PL II MUSIC” or MODE
• No test tone comes out of the rear speakers when “REAR SP” DOWN ∞ to adjust the selected
is set to “NONE.” speaker output level.
5 Adjust the speaker output levels 2
CENTER
3 3) Repeat steps 1) and 2) to adjust
(–10 to +10). the other speaker levels.
Adjust the center speaker and rear speakers levels
comparing to the sound from the front speakers. REAR L
When you select “PL II MUSIC,” you can go to the
5 6
• To adjust the center speaker level, press
following adjustment.
CENTER +/–.
• To adjust the left rear speaker level, press REAR R
REAR•L +/–. 9
• To adjust the right rear speaker level, press
8
4 Turn on Panorama control or off. Remote
NOT
REAR•R +/–. 1) Press ADJUST repeatedly until
“PANORAMA” (with the current ADJUST SETTING
Surround modes. However, no test tone is available when using the DOWN ∞ to select if you turn on
buttons on the front panel. So make adjustments while listening to or off Panorama control.
the sound of the source played back. • Each time you press the button, “ON”
and “OFF” change alternately.
1 Setting the analog or digital input mode for the
source you like to listen and start playing. ON : Select this when you like to enjoy
When playing back software encoded with Dolby Digital and “wraparound” sound effect with side-wall
DTS Digital Surround, select the digital input mode (see page image.
11). OFF : Select this when you like to enjoy
originally recorded sounds.
2 Press SURROUND ON/OFF to SURROUND ON/OFF
22
EN18-23.RX-5020/5022V[C]_f 22 02.1.9, 4:37 PM
English
Using DAP Modes and All Channel Stereo 2 Press SURROUND ON/OFF to SURROUND ON/OFF
The 10 keys are activated for sound adjustments. to adjust the selected speaker
output level.
5 Adjust the speakers output levels REAR L
3) Repeat steps 1) and 2) to adjust
5 6
(–10 to +10).
the other speaker level.
• To adjust the left rear speaker level, press
REAR•L +/–.
• To adjust the right rear speaker level, press
REAR R 5 For DAP modes only: Adjust the effect level.
8 9
REAR•R +/–. 1) Press ADJUST repeatedly until ADJUST SETTI
23
EN18-23.RX-5020/5022V[C]_f 23 01.12.27, 10:13 AM
COMPU LINK Remote Control System
English
The COMPU LINK remote control system allows you to operate Automatic Power On/Off (Standby): only possible with the
JVC’s audio components through the remote sensor on the receiver. COMPU LINK-3 and COMPU LINK-4
To use this remote control system, you need to connect JVC’s audio
Both the CD player and cassette deck (or CD recorder) turn on and
components through the COMPU LINK-4 (SYNCHRO) jacks (see
off (standby) along with the receiver.
below) in addition to the connections using cables with RCA pin
When you turn on the receiver, the CD player or cassette deck (or
plugs (see page 6).
CD recorder) will turn on automatically, depending on which
• Make sure that the AC power cords of these components are
component has been previously selected.
unplugged before connection. Plug the AC power cords only after
When you turn off the receiver, both the CD player and cassette
all connections are completed.
deck (or CD recorder) will turn off (standby).
Synchronized Recording
Cassette deck
Synchronized recording means the cassette deck starts recording as
or
soon as a CD begins playing.
CD recorder
To use synchronized recording, follow these steps:
COMPU LINK-4
(SYNCHRO) 1 Put a tape in the cassette deck and a disc in the
CD player.
2 Press the record (¶) button and the pause (8)
CD player
button on the cassette deck at the same time.
This puts the cassette deck into recording pause.
If you do not press the record (¶) button and pause (8) button at
Notes: the same time, the synchronized recording feature will not
operate.
• There are four versions of COMPU LINK remote control system.
This receiver is equipped with the fourth version—COMPU LINK-4. 3 Press the play (3) button on the CD player.
This version is added systematic operations with the CD recorder to The source changes on the receiver, and as soon as play starts,
the previous version—COMPU LINK-3.
the cassette deck starts recording. When the play ends, the
• If your audio component has two COMPU LINK jacks, you can use
either one. If it has only one COMPU LINK jack, connect it so that it
cassette deck enters recording pause, and stops about 4 seconds
is the last item in the series of components. later.
• To operate the cassette deck or CD recorder using the COMPU
LINK remote control system, set the source name correctly. Notes:
(See page 8.) • During synchronized recording, the selected source cannot be
• Refer also to the manuals supplied with your audio components. changed.
• If the power of any component is shut off during synchronized
This remote control system allows you to use four functions listed recording, the COMPU LINK remote control system may not
below. operate properly. In this case, you must start again from the
beginning.
Remote Control through the Remote Sensor on the Receiver
You can control the connected audio components through the remote
sensor on the receiver using this remote control. Aim the remote
control directly at the remote sensor on the receiver. For details, see
pages 25 to 27.
24
EN24-32.RX-5020/5022V[C]_f 24 01.12.27, 10:13 AM
Operating JVC’s Audio/Video Components
English
You can use the remote control to operate other JVC’s Sound Adjustment
components. You can always perform the following operations:
Operating Audio Components SURROUND ON/OFF : Turn on or off the Surround modes.
SURROUND MODE : Select the Surround modes.
IMPORTANT:
To operate JVC’s audio components using this remote control:
• You need to connect JVC’s audio components through the COMPU
After pressing SOUND, you can use the following buttons for sound
LINK (SYNCHRO) jacks (see page 24) in addition to the adjustment:
connections using cables with RCA pin plugs (see page 6).
SUBWOOFER +/– : Adjust the subwoofer output level.
• Aim the remote control directly at the remote sensor on the receiver.
• If you use the buttons on the front panel, the remote control will not CENTER +/– : Adjust the center speaker output level.
operate that source. To operate a source with the remote control,
REAR•L +/– : Adjust the left rear speaker output level.
the source must be selected using source selecting buttons on the
remote control. REAR•R +/– : Adjust the right rear speaker output level.
• To operate the cassette deck or CD recorder using the COMPU EFFECT : Select the DAP effect level.
LINK remote control system, set the source name correctly. (See
page 8.) TEST : Turn on or off the test tone output.
• Refer also to the manuals supplied with your audio components.
Note:
After adjusting sounds, press the corresponding source selecting
button or CD-DISC to operate your target source by using the 10
keys; otherwise, the 10 keys cannot be used for operating your target
source.
3 : Start playback.
VOLUME
25
EN24-32.RX-5020/5022V[C]_f 25 01.12.27, 10:13 AM
Operating JVC’s Audio/Video Components
English
Note:
Before starting the above operations, make sure that you have
changed the source name correctly. See page 8.
26
EN24-32.RX-5020/5022V[C]_f 26 01.12.27, 10:13 AM
English
DVD menu operations TEST CENTER
Operating Video Components 1 2 3
After pressing DVD (source selecting button), EFFECT REAR L
• Some JVC’s VCRs can accept two types of the control signals— 10 0 10
RETURN 100
remote code “A” and “B.” Before using this remote control, make
sure that the remote control code of the VCR connected to the VCR
jacks is set to code “A.” MENU : Display or erase the menu screen.
• Aim the remote control directly at the remote sensor on each 5/∞
∞/3
3/2
2 : Select an item on the menu screen.
component, not on the receiver.
ENTER : Enter a selected item.
VCR
You can always perform the following operations: TV
STANDBY/ON VCR
Before operating, set TV/CATV selector to TV.
: Turn on or off a VCR. You can always perform the following operations:
VCR CH +/– : Change the TV channels on the VCR. STANDBY/ON TV/CATV
: Turn on or off a TV.
TV/VIDEO : Change the input mode (TV tuner and video
After pressing VCR (source selecting button), you can use the
input).
following buttons for VCR operations:
TV VOLUME +/– : Adjust the volume.
3 : Start playback.
TV/CATV CH +/– : Change the channels.
FF : Fast wind a tape.
REW : Rewind a tape. After pressing TV SOUND (source selecting button), you can use
7 : Stop playback or recording. the following buttons for TV operations:
8 : Pause playback. To release it, press 3. 1 – 9, 0, 100+ (+10) : Select a channel.
REC PAUSE : Press this button to enter recording pause. RETURN (10) : Function as the RETURN button.
Press this button then 3 to start recording.
DVD player
You can always perform the following operations:
STANDBY/ON DVD
: Turn on or off a DVD player.
After pressing DVD (source selecting button), you can use the
following buttons for DVD operations:
3 : Start playback.
4 : Return to the beginning of the current
(or previous) chapter.
¢ : Skip to the beginning of the next chapter.
7 : Stop playback.
8 : Pause playback. To release it, press 3.
27
EN24-32.RX-5020/5022V[C]_f 27 01.12.27, 10:13 AM
Operating Other Manufacturers’ Video Equipment
English
By changing the transmittable signals, you can use the remote To change the transmittable signals for
control supplied for this unit to operate other manufacturers’ operating a CATV converter
equipment.
• Refer also to the manuals supplied with the other products.
• To operate these components with the remote control, first you 1 Set TV/CATV selector to CATV.
need to set the manufacturers’ codes each for TV, CATV 2 Press and hold STANDBY/ON TV/CATV.
converter, VCR and DVD player. 3 Press TV SOUND.
• After replacing batteries of the remote control, set the 4 Enter manufacturer’s code using buttons 1–9,
manufacturers’ codes again. and 0.
5 Release STANDBY/ON TV/CATV.
Now, you can perform the following operations on the CATV
To change the transmittable signals for
converter.
operating a TV
STANDBY/ON TV/CATV
: Turn on or off the CATV converter.
1 Set TV/CATV selector to TV.
TV/CATV CH +/– : Change the channels.
2 Press and hold STANDBY/ON TV/CATV.
3 Press TV SOUND. After pressing TV SOUND (source selecting button), you can
4 Enter manufacturer’s code using buttons 1–9, use the following buttons on the CATV converter:
and 0. 1 – 10, 0, +10 (100+) :Select the channels.
5 Release STANDBY/ON TV/CATV. +10 (100+) button will be function as the
Now, you can perform the following operations on the TV. ENTER button if your equipment requires
pressing ENTER after selecting a channel
STANDBY/ON TV/CATV
number.
: Turn on or off the TV.
TV/VIDEO : Set the input mode (either TV or VIDEO). Note:
TV VOLUME +/– : Adjust the volume. Refer also to the manual supplied with your CATV converter.
TV/CATV CH +/– : Change the channels.
6 Try to operate your CATV converter by pressing
After pressing TV SOUND (source selecting button), you can STANDBY/ON TV/CATV.
use the following buttons on the TV: When your CATV converter turns on or off, you have entered
1 – 10, 0, +10 (100+) :Select the channels.
the correct code.
+10 (100+) button will be function as the
ENTER button if your TV requires pressing If there are more than one code listed for your brand of
ENTER after selecting a channel number. CATV converter, try each one until the correct one is entered.
Note:
Manufacturers’ codes for CATV converter
Refer also to the manual supplied with your TV.
Manufacturer Codes
JVC 01*
Hitachi 10
Magnavox 02
Mitsubishi 03
Panasonic 04, 11
RCA 05
Samsung 12
Sanyo 13
Sharp 06
Sony 07
Toshiba 08
Zenith 09
*Initial setting
28
EN24-32.RX-5020/5022V[C]_f 28 01.12.27, 10:13 AM
ent
English
To change the transmittable signals for To change the transmittable signals for
operating a VCR operating a DVD player
1 Press and hold STANDBY/ON VCR. 1 Press and hold STANDBY/ON DVD.
2 Press VCR. 2 Press DVD.
3 Enter manufacturer’s code using buttons 1–9, 3 Enter manufacturer’s code using buttons 1–9,
and 0. and 0.
4 Release STANDBY/ON VCR. 4 Release STANDBY/ON DVD.
Now, you can perform the following operations on the VCR. Now, you can use the following buttons on the DVD player.
STANDBY/ON VCR : Turn on or off the VCR. STANDBY/ON DVD : Turn on or off the DVD player.
VCR CH +/– : Change the channels.
After pressing DVD (source selecting button), you can use the
After pressing VCR (source selecting button), you can use the following buttons on the DVD player:
following buttons on the VCR: 3 : Start playback.
3 : Start playback. 7 : Stop playback.
FF : Fast-wind a tape. ¢ : Skip to the beginning of the next
chapter.
REW : Rewind a tape.
4 : Return to the beginning of the current
7 : Stop playback or recording.
(or previous) chapter.
8 : Pause playback. To release it, press 3.
8 : Pause playback. To release it, press 3.
REC PAUSE : Press this button to enter recording
pause. DVD menu operations TEST CENTER
1 2 3
Press this button then 3 to start After pressing DVD (source EFFECT REAR L
recording. selecting button), you can use the 4 5 6
MENU REAR R
following buttons for DVD menu 7/P 8 9
operations: ENTER SUBWOOFER
Note: 10 0 10
RETURN 100
Refer also to the manual supplied with your VCR.
5 Try to operate your VCR by pressing MENU : Display or erase the menu screen.
STANDBY/ON VCR.
5/∞
∞/3
3/2
2 : Select an item on the menu screen.
When your VCR turns on or off, you have entered the correct
code. ENTER : Enter a selected item.
If there are more than one code listed for your brand of
VCR, try each one until the correct one is entered. 5 Try to operate your DVD player by pressing
STANDBY/ON DVD.
When your DVD player turns on or off, you have entered the
Manufacturers’ codes for VCR correct code.
Manufacturer Codes
29
EN24-32.RX-5020/5022V[C]_f 29 01.12.27, 10:13 AM
Troubleshooting
English
Use this chart to help you solve daily operational problems. If there is any problems you cannot solve, contact your JVC’s service center.
The power does not come on. The power cord is not plugged in. Plug the power cord into an AC outlet.
No sound from speakers. Speaker signal cables are not connected. Check speaker wiring and reconnect if
necessary.
The SPEAKERS ON/OFF button is not Press SPEAKERS ON/OFF button correctly.
set correctly.
An incorrect input mode (analog or Select the correct input mode (analog or
digital) is selected. digital).
Sound from one speaker only. Speaker signal cables are not connected Check speaker wiring and reconnect if
properly. necessary.
The balance is set to one extreme. Adjust the balance properly (see page 15).
Continuous hiss or buzzing during FM Incoming signal is too weak. Connect an outdoor FM antenna or contact
reception. your dealer.
An incorrect antenna is used. Check with your dealer to be sure you have
the correct antenna.
Occasional cracking noise during FM Ignition noise from automobiles. Move the antenna farther from automobile
reception. traffic.
“OVERLOAD” starts flashing on the Speakers are overloaded because of high 1. Press STANDBY/ON on the front
display. volume. panel to turn off the receiver.
2. Stop the playback source.
3. Turn on the receiver again, and adjust the
volume.
Speakers are overloaded because of short Press STANDBY/ON on the front panel,
circuit of speaker terminals. then check the speaker wiring.
If “OVERLOAD” does not disappear, unplug
the AC power cord, then plug it back again.
If speaker wiring is not short-circuited, contact
your dealer.
“DSP MICON NG” starts flashing on the The built-in microcomputer is not Press STANDBY/ON on the front panel to
display. functioning correctly. turn off the receiver. After unplugging the
power cord, consult your dealer.
The STANDBY lamp lights up after The receiver is overloaded because of a Press STANDBY/ON on the front panel to
turning on the power, but soon the high voltage. turn off the receiver. After unplugging the
receiver turns off (into standby mode). power cord, consult your dealer.
Remote control does not work. There is an obstruction in front of the Remove the obstruction.
remote sensor on the receiver.
Remote control does not work as you The remote control is not ready for your Press SOUND or a source selecting button
intend. intended operation. first, then press the buttons you want to use.
(See pages 25 to 27).
30
EN24-32.RX-5020/5022V[C]_f 30 01.12.27, 10:13 AM
Specifications Designs & specifications are subject to change without notice.
English
Amplifier
Output Power
At Stereo operation:
Audio
Audio Input Sensitivity/Impedance (1 kHz): CD, TAPE/CDR, TV SOUND, VCR, DVD:
220 mV/47 k Ω
Audio Input (DIGITAL IN)* : Coaxial: DIGITAL 1 (DVD): 0.5 V (p-p)/75 Ω
Optical: DIGITAL 2 (CD): –21 dBm to –15 dBm (660 nm ±30 nm)
* Corresponding to Linear PCM, Dolby Digital, and DTS Digital Surround
(with sampling frequency — 32 kHz, 44.1 kHz, 48 kHz).
Audio Output Level: TAPE/CDR, VCR: 220 mV
Signal-to-Noise Ratio (’66 IHF/’78 IHF): CD, TAPE/CDR, TV SOUND, VCR, DVD: 87 dB/78 dB
Frequency Response (8 Ω): CD, TAPE/CDR, TV SOUND, VCR, DVD: 20 Hz to 20 kHz (±1 dB)
Tone Control: Bass (100 Hz): ±10 dB
Treble (10 kHz): ±10 dB
Video
Video Input Sensitivity/Impedance:
Composite video: VCR, DVD: 1 V (p-p)/75 Ω
Video Output Level/Impedance:
Composite video: VCR, MONITOR OUT: 1 V (p-p)/75 Ω
Synchronization: Negative
Signal-to-Noise Ratio: 45 dB
31
EN24-32.RX-5020/5022V[C]_f 31 01.12.27, 10:14 AM
Specifications
English
FM tuner (IHF)
Tuning Range: 87.5 MHz to 108.0 MHz
Usable Sensitivity: Monaural: 12.8 dBf (1.2 µV/75 Ω)
50 dB Quieting Sensitivity: Monaural: 21.3 dBf (3.2 µV/75 Ω)
Stereo: 41.3 dBf (31.5 µV/75 Ω)
Signal-to-Noise Ratio (IHF-A weighted): Monaural: 78 dB at 85 dBf
Stereo: 73 dB at 85 dBf
Total Harmonic Distortion: Monaural: 0.4% at 1 kHz
Stereo: 0.6% at 1 kHz
Stereo Separation at REC OUT: 35 dB at 1 kHz
Alternate Channel Selectivity: 45 dB: (±400 kHz)
Frequency Response: 30 Hz to 15 kHz: (+0.5 dB, –3 dB)
AM tuner
Tuning Range: 530 kHz to 1 710 kHz
Usable Sensitivity: Loop antenna: 400 µV/m
Signal-to-Noise Ratio: 50 dB (100 mV/m)
General
Power Requirements: AC 120V , 60 Hz
Power Consumption: 180 W/230 VA (at operation)
2 W (in standby mode)
Dimensions (W x H x D): 435 mm x 146.5 mm x 416 mm
(17 3/16 in. x 5 13/16 in. x 16 7/16 in.)
Mass: 8.8 kg (19.5 lbs)
32
EN24-32.RX-5020/5022V[C]_f 32 01.12.27, 10:14 AM
VICTOR COMPANY OF JAPAN, LIMITED
EN, FR V
J C 0102NHMMDWJEIN