Professional Documents
Culture Documents
Sample EngDrawings PDF
Sample EngDrawings PDF
Sample EngDrawings PDF
O N
<Design>
Shallow End
100
Min
main drain in Mid HRV pools Refer to Detail 5.3 300 Max
Depth
Depth
Sheet 5 for extra reinf .
Flat Ends Mid HRV
500
Min
<Design>
C
Vert/TransverseCTS
U
Thickness, <Design> MPa
<Design> cover to Ensure all excavation
pool side reinf . corners are free of spoil 300 WIDTH
HRV Sump under lowest point
R
Reinforcement must be prior to spray
of floor. <Design>
radius bent to suit cove.
NOTES:
Do not square bend
di
Compliant Anti-vortex
Covers not able to be
removed without tools
4.1 LONGITUDINAL SECTION
dinside
REINF AT HRV :
<Design>
O N HRV
lap 450 min. Stagger alternate laps where possible.
<Design>
Skimmer Reinf :
<Design>
Pool penetration &
suction pipes
<Design>
di
NOTE: Suction and covers
to be compliant with
AS 1926-3 2003 Section 5.
Main Reinf
C <Design>
<Design>
Skimmer Throat
O R
<Design>
T.W.L.
See Pool Plan
4.5 HRV REINF PLAN VIEW
DROPPERS:
See Table 2
WATER SIDE
<Design>
Cover to
Horiz Bars
Depth
SECTION
VIEW
REINF AT SKIMMER:
FRONT VIEW
T
Form Bars:
<Design> <Design>
N O
Refer to detail 4.2 for Long Steps where
massed construction is not required.
DropperCTS
Into Floor
Into Wall
<Design>
<Design>
<Design>
Scale: 1:50 typ
4.7 SKIMMER BLOCK DETAIL
Date: 02/2011
PLAN VIEW
NOTE: Skimmer to
be compliant with
AS 1926-3 2003
Section 4.
WirraWongaP/L 2011
This drawing and any information set out hereon is the
copyright property of WirraWonga Pty Ltd, and must not
checked for applicabilility to the referenced pool
4.2 TYPICAL CROSS SECTION JN: 11- DWG: GA11 be loaned, modified, copied or used for any purpose
Note: Swimout Ledge may be positioned
plan only, and must not be used for other projects
anywhere around pool perimeter
AT HRV AND SWIMOUT LEDGE Checked: * Sheet: 4
other than that relating to the project for which it was
prepared.
ADDITIONAL INFORMATION - FEATURE, RAISED & RETAINING WALL DETAILS WirraWonga
TO BE READ IN CONJUNCTION WITH POOL PLAN 11-xxxx SHEET 2 & GENERAL ARRANGEMENT SHEET 4 Consulting Engineers
<Design> <Design> WALL DESIGN PARAMETERS:
BLOCK WALL: Bulk Density of earth : kN/m3
<Design>
BLOCK WALL:
See Table 3 for Reinf .
SPRAYED WALL REINF :
<Design>
See Table 4 for Reinf
N
Shear Angle
Cohesion
O
C:
Hydrostatic load
:
kPa
<Design>
Surcharge Load: kPa
<Design>
WALL STARTER BARS:
<Design> SPRAYED WALL REINF :
<Design>
<Design>
I
FULL MASONRY WALL
<Design>
<Design> <Design>
U
4. Retaining WallReinf Details
DROPPERS: Wall StarterCTS <Design>
See Table 4 All retaining walls
R
Pool to be fully drained Block WallVert CTS <Design>
Max Shell
to level of pool coping
Depth Block WallHoriz CTS <Design>
See Drainage Notes
DROPPERS:
See Table 3
<Design>
<Design>
S T
DRAINAGE NOTES: Drainage behind masonry retaining walls
N
Block WallVert CTS <Design>
Block WallHoriz CTS <Design> 5.2 RETAINING WALL DETAIL
C O
NOTE: Refer to attached specifications
for masonry construction requirements
and control joint spacings
TIMBER DECKING:
Design by others.
May be supported onto Pool Shell.
<Design>
Deck by others <Design>
Fixing Detail:
<Design>
Reinf : F O
<Design>
Wall Reinf :
<Design>
Reinf :
<Design>
T
<Design>
<Design>
<Design>
<Design>
O
EJ to Joist Support
N
Ledger
NOTE: This drawing has
<Design> <Design> been engineer checked for SUPPORTING DECKING LOADS
applicabilility to the ALTERNATIVE
referenced pool plan only, Scale: NTS Date: 02/2011 This drawing and any information set out hereon is the
and must not be used for copyright property of WirraWonga Pty Ltd, and must not
other projects JN: 11- DWG: GA11 be loaned, modified, copied or used for any purpose
5.3 OUT OF GROUND (EXPOSED) POOL WALL DETAIL WirraWongaP/L 2011 Checked: * Sheet: 5
other than that relating to the project for which it was
prepared.
O N
T I
U C
T R
N S
C O
O R
F
O T
N