Professional Documents
Culture Documents
Cat Rex A10VO Series52 PDF
Cat Rex A10VO Series52 PDF
A10VO
Data sheet
Series 52/53
Size 10...85
Nominal pressure 3600 psi (250 bar)
Peak pressure 4600 psi (315 bar)
Open circuit Series 52 Series 53
Contents Features
Ordering code - standard program 2 – Variable axial piston pump in swash plate design for hydro-
static drives in open circuits
Hydraulic fluids 4
– Flow is proportional to drive speed and displacement. The
Technical data 5
flow is infinitely variable by adjustment of the swash plate.
Operating curves for pumps with pressure control 8
– Strong bearings for long service life
DR - Pressure control 9
– High permissible drive speeds
DRG - Pressure control, remote 10
– High power to weight ratio
DRF (DFR) and DRS (DFR1) - pressure and flow control 11
– Small dimensions
LA... - pressure, flow and power control 12
– Low noise level
Unit dimensions, size 10 14
– Good suction characteristics
Unit dimensions, size 18 16
– Axial and radial loading of drive shaft possible
Unit dimensions, size 28 20
– Pressure and flow control
Unit dimensions, size 45 24
– Electro-hydraulic pressure control
Unit dimensions, size 63 28
– Power control
Unit dimensions, size 85 32
– Electro-proportional displacement control
Combination pumps A10VO + A10V(S)O 36
– Short response times
Overview of through drive mounting options 36
Dimensions through drives 37
Installation notes 40
General information 44
/44 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 703/11.07
Operating mode
02 Pump, open circuit O
Size 10 18 28 45 63 85
in3 0.61 1.10 1.71 2.75 3.84 5.18
03 ~displacement Vg max in
(cm3) (10) (18) (28) (45) (63) (85)
Control devices1)
Pressure control DR DR
with hydraulic flow control
X-T open D F R – DFR
X-T open DR F – DRF
X-T closed DFR1 – DFR1
X-T closed DR S – DRS
with flow control, electro-hydraulic adjustment of differential pressure (inverse proportional characteristic), (RA 92 709)
EF . D . – EF.D.
with remote pressure control
hydraulic DR G DRG
electric, inverse characteristic ED . – ED.
Power control
with pressure control
minimum start of control
145 to 510 psi (10 to 35 bar) LA 5 D – LA5D
04
520 to 1015 psi (36 to 70 bar) LA 6 D – LA6D
1030 to 1520 psi (71 to 105 bar) LA 7 D – LA7D
1535 to 2030 psi (106 to 140 bar) LA 8 D – LA8D
2045 to 3335 psi (141 to 230 bar) LA 9 D – LA9D
with remote pressure control
min. start of control see above LA X D G – LAXDG
with pressure and flow control, X-T closed
min. start of control see above LA X D S – LAXDS
with press. and flow controlol electr. adjustment of diff. press. (inverse prop. characteristic), X-T closed (RA 92 709)
min. start of control see above LA X S . – LAXS.
Electro-proportional displacement control (RA 92 708)
with pressure and flow control, positive characteristic
EP . D . – EP.D.
with pressure and flow control, positive characteristic; deactivation of control at I = 0
EK . D . – EK.D.
Series
05 5
1) For availability of control options in series 52 and 53 see index 06 in ordering code
RA 92 703/11.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. /44
A10V(S) O / 5 – V
01 02 03 04 05 06 07 08 09 10 11 12
Index 10 18 28 45 63 85
DR, DFR, DFR1, DRG, ED – 21)
06 DR, DRF, DRS, DRG, ED... – 3
EF..., LA..., EP..., EK... – 3
Direction of rotation
viewing on shaft end right hand R
07
left hand L
Seals
08 FKM (fluor-rubber) V
Shaft end 10 18 28 45 63 85
Splined shaft to SAE J744, standard shaft S
Similar to shaft „S“ however for higher input torque – – R
09 Splined shaft to SAE J744, reduced diameter, not for through drive – U
Similar to shaft „U“ higher input torque, not for through drive – – – W
Parallel shaft SAE with key – – K2)
Tapered with Woodruff key – – – C2)
Mounting flange
SAE 2-hole C
10
SAE 4-hole – – – – D
Through drive
Without through drive (standard for version 61 and 64) N00
Flange SAE J744 Coupler for splined shaft3) Sealing
82-2 (A) 5/8 in 9T 16/32DP axial – K01
82-2 (A) 3/4 in 11T 16/32DP axial – K52
12 101-2 (B) 7/8 in 13T 16/32DP axial – – K68
101-2 (B) 1 in 15T 16/32DP axial – – – K04
127-4 (C) 1 1/4 in 14T 12/24DP axial – – – – – K15
127-2 (C) 1 1/4 in 14T 12/24DP axial – – – – – K07
127-2 (C) 1 1/2 in 17T 12/24DP axial – – – – – K24
1) Not for new projects. For new projects use only series 53.
2) only Series 52
3) 30° pressure angle, flat base, flank centering, fit class 5
Hydraulic fluids
Prior to project design, please see our technical data sheets Notes on the selection of the hydraulic fluid
RE 90220 (mineral oil), RE 90221 (environmentally acceptable
fluids) and RE 90223 (HF-fluids) for detailed information on In order to select the correct fluid, it is necessary to know the
fluids and operating conditions. operating temperature in the tank (open circuit) in relation to
the ambient temperature.
When using HF- or environmentally acceptable fluids attention
must be paid to possible limitations of the technical data, if The fluid should be selected so that within the operating
necessary contact us. (when ordering please state in clear text temperature range, the viscosity lies within the optimum range
the fluid to be used). Operation on Skydrol is only possible (nopt), see shaded section of the selection diagram. We recom-
after consultation with us. mend to select the higher viscosity grade in each case.
At temperatures between -13 °F (-25 °C) and -40 °F (-40 °C) If above mentioned grades cannot be maintained please con-
special measures may be required, depending on installation sult us.
conditions. Please consult us for further information.
For detailed information on operation with low temperatures
see data sheet RE 90300-03-B.
Selection diagram
-40° -4° 32° 68° 104° 140° 176° 212° °F
-40° -20° 0° 20° 40° 60° 80° 100° °C
7400 1600 1600 7400
4600 1000
3000 600
2000 400
VG 68
1000
VG
VG 22
VG 32
VG 46
200
10
Viscosity n [mm2/s]
500 100
0
300 60
200 40 36 170
nopt
100 20
80 16 80
60 10
Technical data
Operating pressure range Maximum permissible speed (Speed limit)
Permissible speed by increase of inlet pressure pabs at the inlet
Inlet
port S or reduction of displacement (Vg ≤ Vg max ).
Absolute pressure at port S
pabs min _ __________________________________12 psi (0,8 bar) 1.2
[rpm]
the diagram to the right. 1.1
17.5 (1.2)
max
Outlet
Speed n/n0
Pressure at port B
1.0 14.5 (1.0)
Nominal pressure pN ___________________ 3600 psi (250 bar)
Peak pressure pmax _____________________ 4600 psi (315 bar) 13 (0.9)
S to B.
Technical data
Table of values (theoretical values, without considering efficiencies and tolerances; values rounded)
Size A10V(S)O 10 18 28 45 63 85
Displacement Vg max in3 0.64 1.10 1.71 2.75 3.84 5.18
(cm3) (10,5) (18) (28) (45) (63) (85)
Speed1)
max. at Vg max n0 max rpm 3600 3300 3000 26002) 2600 2500
max. at Vg < Vg max n0 max zul rpm 4320 3960 3600 3120 3140 3000
Flow
at n0 max qV0 max gpm 9.7 15.6 22 31 43 55
(L/min) (37) (59) (84) (117) (163) (212)
at nE=1500 min-1 qVE max gpm 4 7.1 11.1 18 25.1 34
(L/min) (15) (27) (42) (68) (95) (128)
Power Dp = 3600 psi
(250 bar)
at n0 max Po max HP (kW) 22 (16) 34 (25) 47 (35) 65 (49) 90 (68) 119 (89)
at nE=1500 min-1 PE max HP (kW) 9.4 (7) 15 (11) 24 (18) 38 (28) 52 (39) 71 (53)
Torque
at Vg max Dp = 3600 psi Tmax lb-ft 31 52 82 132 184 247
(250 bar) (Nm) (42) (71) (111) (179) (250) (338)
Dp = 1440 psi T lb-ft 13 21 33 53 74 102
(100 bar) (Nm) (17) (29) (45) (72) (100) (135)
Torsional stiffness Shaft S c lb-ft/rad 6760 8082 16400 27560 48100 105100
(Nm/rad) (9200) (11000) (22300) (37500) (65500) (143000)
Shaft R c lb-ft/rad – 10870 19400 30240 51200 –
(Nm/rad) – (14800) (26300) (41000) (69400) –
Shaft U c lb-ft/rad 5020 5870 – 22130 36290 75900
(Nm/rad) (6800) (8000) – (30000) (49200) (102900)
Shaft W c lb-ft/rad – – – 25370 39830 86960
(Nm/rad) – – – (34400) (54000) (117900)
Shaft K/C c lb-ft/rad 7965 – 19770 32380 54506 –
(Nm/rad) (10800) – (26800) (43900) (73900) –
Moment of inertia rotary group JTW lbs-ft2 0.0142 0.2207 0.0403 0.0783 0.1329 0.2848
(kgm2) (0,0006) (0,00093) (0,0017) (0,0033) (0,0056) (0,012)
Angular acceleration, max.3) a rad/s2 8000 6800 5500 4000 3300 2700
Fill volume V gal 0.05 0.06 0.08 0.13 0.21 0.26
(L) (0,2) (0,25) (0,3) (0,5) (0,8) (1)
Weight approx. (without fluid) m lbs (kg) 17 (8) 25 (11,5) 31 (14) 40 (18) 48.5 (22) 75 (34)
1) Values are valid with inlet pressure of 15 psi (1 bar) at suction inlet S. With reduced displacement or increased inlet
pressure the drive speed can be increased according to the diagram on page 5.
2) For higher drive speeds please consult us.
3) –These values are valid for conditions between the min. required and the max. permissible drive speeds.
For external sources of excitation (eg. diesel engine 2-8 fold rotary frequency, cardan shaft 2 fold rotary frequency).
– The limit is valid for a single pump.
– The load carrying capacity of the connecting parts must be taken into consideration.
Caution: Exceeding these limits can lead to a loss of operability, reduction of service life or complete destruction of the axial
piston unit. The permissible values can be calculated.
RA 92 703/11.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. /44
Technical Data
Determination of pump size
Size 10 18 28 45 63 85
Radial force, max. Fq
at Fq max lbf 56 78 270 337 382 450
X/2 (N) (250) (350) (1200) (1500) (1700) (2000)
X/2 X/2
X
TD
/44 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 703/11.07
(Fluid: mineral oil to ISO VG 46 DIN 51519, t = 122 °F (50 °C)) – – – – n = 1500 rpm
n = 2600 rpm
Size 10
gpm (L/min) (kW) HP
– – – – n = 1500 rpm 30
(120) (60) 80
n = 3600 rpm (50)
(100) qv
25
Drive power P qV
(35) (20) 25 Pqv min 20
5 (20) (10)
7.5 qV (15) 20
Flow qV
35
(120) qv (60) 80
30
(100) Pqv max (50)
gpm (L/min) (kW) HP 25 60
(40)
(40) 20 (80)
(60) 50
Drive power P qV
15 (60) (30) 40
qV 15
(50) (30) 40
Flow qV
10 (40) (20)
10 Pqv min 20
(40) (20) (10)
20 5 (20)
pqV max
(30) pqV min (10) 0 0
(50) (100) (150) (200) (250) (bar)
5 (20) (0) 0
0 (50) (100) (150) (200) (250) (bar) 0 1000 2000 3000 3625 psi
Operating pressure p
1000 2000 3000 3625 psi
Operating presure p
Size 85
– – – – n = 1500 rpm
Size 28 n = 2500 rpm
40
Drive power Pqv
(30) 40 100
15 (60)
Drive power P qV
35
10 (40) (20)
20 (120) (60) 80
30
5 (20) Pqv min (10)
(100) (50)
25 pqV max
0 0 60
(80) (40)
(50) (100) (150) (200) (250) (bar) 20
0 1000 2000 3000 3625 psi 15 (60) (30) 40
Operating pressure p 10 (40) (20)
pqV 0
20
5 (20) (10)
0 0
(50) (100) (150) (200) (250) (bar)
0 1000 2000 3000 3625 psi
Operating pressure
qV • p qV
ht = hV =
PpV max • 600 qV theor
RA 92 703/11.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. /44
DR - Pressure control
Adjustment range
setting range
290 (20)
min max L2 S
Flow qV [gpm (L/min)]
Dynamic characteristic
Ports
The curves show average measured values under test condi-
B Outlet port
tions.
S Inlet port
Conditions: n = 1500 rpm L, L1/2 Case drain port (L1/2 plugged)
tfluid = 120 °F (50 °C)
Control data
Line main relief set at 4570 psi (315 bar)
Hysteresis and repeatability Dp max. 45 psi (3 bar)
Stepped loading by suddenly opening or closing the pressure
Pilot fluid consumption max. approx. 0.8 gpm (3 L/min)
line using a pressure relief valve at 3.3 ft (1 m) downstream
Flow loss at qV max see page 8
from the pump pressure outlet.
Control times
psi (bar)
4570 (315)
4350 (300)
tSA [ms] tSA [ms] tSE [ms]
Operating pressure p
3620 (250)
Size against 725 psi against 3200 psi standby - 3600 psi
2900 (200)
(50 bar) (220 bar) (250 bar)
2175 (150) 10 70 50 15
1450 (100) 18 70 70 30
725 (50) 28 70 65 20
0 45 85 75 25
Vg max 63 100 80 30
85 120 100 40
Displacement
(swivel angle)
Vg min
Control time
stroking time tSA de-stroking time tSE
10/44 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 703/11.07
Control data
See page 9
L2 S
Ports
B Outlet port
S Inlet port
L, L1/2 Case drain ports (L1/2 plugged)
X Pilot pressure port
RA 92 703/11.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. 11/44
DpV
see table of values
3625 (250)
Operating press. pB [bar]
Setting range
L2 S
Differential pressure Dp
Flow qV
The curves are measured average values under test conditions Control data
(bar) psi
100 (315) 4570 For pressure control see page 9.
Displacement Vg (%)
(250) 3620 Max. flow deviation (hysteresis and rise) measured at a drive
Load pressure p
75
(200 2900 speed of n = 1500 rpm.
50 (150 2170
Size 10 18 28 45 63 85
(100) 1450
25
(50 725
Dqvmax
0.13 0.24 0.26 0.48 0.66 0.83
0
(18) 260 gpm
(stand by)
Control time (0,5) (0,9) (1,0) (1,8) (2,5) (3,1)
(L/min)
stroking time tSA de-stroking time tSE
Control times Pilot fluid consumption DRF (DFR) max. approx. 0.8...1.2 gpm
(3...4,5 L/min)
tSA [ms] tSE [ms] tSE [ms] Pilot fluid consumption DRS (DFR1) max. approx. 0.8 gpm
(3 L/min)
Size stand by - 3600 psi 3600 psi (250 bar) 725 psi (50 bar)
Flow loss at qVmax see page 8
(250 bar) - stand by - stand by
Possible control valves to be used on B
10 60 15 40 (not included in supply of pump)
18 65 18 45
LS-Mobile control valves
28 70 20 50 Mobile valve block M4-12 (RE 64278)
45 85 25 60 Mobile valve block M4-15 (RE 64282)
Execution of pressure control like DR(G), see pages 9/10. When ordering please state the max. input torque in clear text.
Execution of pressure and flow control like DRS, see page 11.
Control data
In order to achieve a constant drive torque with varying
operating pressures, the swivel angle and with it the output For technical data of pressure control see page 9.
flow of the pump, is varied in such a manner, that the product
For technical data of pressure and flow control see page 11.
of flow and pressure remains constant.
Pilot fluid consumption max. approx. 0.8 gpm (3,0 L/min)
Flow control is possible below the limit of the power curve.
Flow loss at qV max see page 8
4350 (300)
3620 (250)
LA8
X X
not included in
LA7
supply
L L1
LA6 B
LA5
Ports
0 Flow qV [%] 100
B Outlet port
S Inlet port
L, L1 ,L2 Case drain ports (L1 ,L2 plugged)
X pilot pressure port L2 S
RA 92 703/11.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. 13/44
Notes
14/44 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 703/11.07
6)
L
(5
0.43 (11)
20
0.25 (6.4)
2.
Flange SAE J744
4.06 (103)
82-2 (A)
3.248 DIA (Ø 82.55h8)
0. )
DIA 0.43
35
(9
(Ø 11)
45°
Y
2.11 (53.5)
2.20 (56)
3.250
L1 4.19 (106.4)
0.94 (24) 5.28 (134)
5.83 (148)
7.09 (180)
View Y right hand rotation View Y left hand rotation
S B B S
Shaft ends
S Spline shaft U Spline shaft K Parallel keye shaft 0.188 (4.76 +0.025 )
3/4 in 11T 16/32DP1) 5/8 in 9T 16/32DP1) 0.01(2.5) 1.13 0.187
+0.05
ø 5/8 in
0.833
DIA
Ports
Tightening torque, max.2)
B Outlet port ISO 11926 1 1/16-12UNF-2B; 0.79 (20) deep 261 lb-ft (360 Nm)
S Inlet port ISO 11926 1 1/16-12UNF-2B; 0.79 (20) deep 261 lb-ft (360 Nm)
L/L1 Case drain port (L1 plugged) ISO 11926 9/16-18UNF-2B; 0.47 (12) deep 58 lb-ft (80 Nm)
1) ANSI B92.1a-1996, 30° pressure angle, flat root, side fit, tolerance class 5
2) see general information
3) axial retention of coupling half eg. with clamp coupling or with clamping screw
RA 92 703/11.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. 15/44
6)
(5
Flange SAE J744 L
20
2.
82-2 (A)
4.02 (102)
45°
3.250 DIA (ø 82.55 )
3.74 (95)
h8
DIA 0.43
0.3 )
5
(9
45°
2.20 (56)
3.248
L1
0.94 (24) 4.19 (106.4)
5.83 (148) 5.28 (134)
7.09 (180)
S B B S
1.13 1.13 1.13 1.13
(28.6)(28.6) (28.6)(28.6)
2.00 (51) 2.00 (51) 2.00 (51) 2.00 (51)
Ports
Tightening torque, max.1)
B Outlet port ISO 11926 1 1/16-12UNF-2B; 0.79 (20) deep 261 lb-ft (360 Nm)
S Inlet port ISO 11926 1 1/16-12UNF-2B; 0.79 (20) deep 261 lb-ft (360 Nm)
L/L1 Case drain port (L1 plugged) ISO 11926 9/16-18UNF-2B; 0.47 (12) deep 58 lb-ft (80 Nm)
X Pilot pressure port ISO 11926 7/16-20UNF-2B; (11.5) deep 29 lb-ft (40 Nm)
1) see general information
16/44 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 703/11.07
3.27 (83)
0.31 (7.8) 0.39 (10)
0.96
(24.5) L1
L1
Flange SAE J744
4.80 (122)
82-2 (A) L
0.1
2.83 (72)
(2
.5
)
L
3.250 DIA (Ø82.55 )
0.43 (11)
h8
45°
)5
1.
(6
)
42
5
1.
2.
(6
Y
42
2.
2.48 (63)
3.248
45°
L2
3.27 (83) 4.20 (106.4)
6.14 (156) 5.35 (136)
max. 7.20 (183)
View Y
port plate 61
1.87 (47.6)
(Ø20)
0.79
S B
1.19 0.87
(30.2) (22.2)
1.26 1.10
Location of service ports for left hand rotation; turn port plate180° (32) (28)
Shaft ends
S Spline shaft R Spline shaft U Spline shaft
3/4 in 11T 16/32DP1) 3/4 in 11T 16/32DP1) 5/8 in 9T 16/32DP1)
(SAE J744 - 19-4 (A-B)) (SAE J744 - 19-4 (A-B)) (SAE J744 - 16-4 (A))
1/4-20UNC-2B
ø 3/4 in
ø 5/8 in
ø3/4 in
Ports
Tightening torque, max.2)
B Outlet port, SAE flange (code 61) SAE J518c 3/4in
Fixing thread ISO 68 3/8-16UNC-2B; 0.75 (19) deep 31 lb-ft (42 Nm)
S Inlet port, SAE flange (code 61) SAE J518c 1 1/4in
Fixing thread DIN 13 7/16-14UNC-2B; 0.79 (20) deep 48 lb-ft (66 Nm)
L/L1,2 Case drain ports (L1,2 plugged) ISO 11926 3/4-16UNF-2B 116 lb-ft (160 Nm)
1) ANSI B92.1a-1996, 30° pressure angle, flat root, side fit, tolerance class 5
2) see general information
3) axial retention of coupling half, eg. with clamp coupling or with clamping screw
RA 92 703/11.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. 17/44
4.80 (122)
Flange SAE J744
82-2 (A) L
2.83 (72)
2.
3.250 DIA (Ø82.55 )
5
0.43 (11)
h8
45°
)5
1.
(6
2.31 (58.7)
)
42
5
1.
1.26 DIA
2.
(6
(Ø32)
Y
42
2.
2.48 (63)
3.248
45°
S L2
3.27 (83) 1.19 (30.2) 4.19 (106.4)
5.63 (143) 5.35 (136)
6.70 (170)
2.44 (62)
View Y X
port plate 62
4.17 (106)
View Z
0.79 DIA(Ø20)
1.87 (47.6)
B 0.87
(22.2)
Location of service ports for left hand rotation; turn port plate180°
Ports
Tightening torque, max.1)
B Outlet port, SAE flange (code 61) SAE J518c 3/4in
Fixing thread ISO 68 3/8-16UNC-2B; 0.75 (19) deep 31 lb-ft (42 Nm)
S Inlet port, SAE flange (code 61) SAE J518c 1 1/4in
Fixing thread DIN 13 7/16-14UNC-2B; 0.79 (20) deep 48 lb-ft (66 Nm)
L/L1,2 Case drain ports (L1,2 plugged) ISO 11926 3/4-16UNF-2B 116 lb-ft (160 Nm)
X Pilot pressure port ISO 11926 7/16-20UNF-2B; 0.45 (11.5) deep 29 lb-ft (40 Nm)
1) see general information
18/44 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 703/11.07
8.86 (225)
4.45 (113)
3.27 (83)
0.31 (7.8) 0.39 (10)
0.96 (24.5)
L1
Flange SAE J744
4.80 (122)
4.45 (113)
82-2 (A)
L
2.83 (72)
0.1 .5)
(2
3.248 DIA (Ø82.55h8)
0.43 (11)
45°
) 5
1.
(6
) 5
42
1.
(6
2.
Y
42
2.
2.48 (63)
3.250
45°
L2
3.27 (83) 4.19 (106.4)
6.14 (156) 5.35 (136)
View Y 2.44 (62)
port plate 61 X
4.13 (105)
0.79 (Ø20)
1.26 DIA (Ø32)
2.31 (58.7)
1.87 (47.6)
S B
1.19 0.87
(30.2) (22.2)
1.26 1.10
Location of service ports for left hand rotation; turn port plate180° (32) (28)
Ports
Tightening torque, max.1)
B Outlet port, SAE flange (code 61) SAE J518c 3/4in
Fixing thread ISO 68 3/8-16UNC-2B; 0.75 (19) deep 31 lb-ft (42 Nm)
S Inlet port, SAE flange (code 61) SAE J518c 1 1/4in
Fixing thread DIN 13 7/16-14UNC-2B; 0.79 (20) deep 48 lb-ft (66 Nm)
L/L1,2 Case drain ports (L1,2 plugged) ISO 11926 3/4-16UNF-2B 116 lb-ft (160 Nm)
X Pilot pressure port ISO 11926 7/16-20UNF-2B; 0.45 (11.5 deep) 29 lb-ft (40 Nm)
1) see general information
RA 92 703/11.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. 19/44
8.86 (225)
4.45 (113)
3.27 (83)
0.31 (7.8) 0.39 (10)
0.96 (24.5)
L1
4.45 (113)
4.80 (122)
82-2 (A) L
0.1 .5)
2.83 (72)
(2
0 0.43 (11)
(Ø82.55h8)
45°
5)
1.
(6
2.31 (58.7)
5)
42
1.
Y
1.26 (Ø32)
(6
2.
42
3.250 DIA
2.
2.48 (63)
45°
3.248
S L2
3.27 (83) 1.19 (30.2) 4.19 (106.4)
5.63 (143) 5.35 (136)
6.69 (170)
View Y 2.44 (62)
Port plate 62 X
4.17 (106)
View Z
1.87 (47.6)
0.79 DIA
Z
(Ø20)
B 0.87
S B
(22.2)
Location of service ports for left hand rotation; turn port plate180°
Ports
Tightening torque, max.1)
B Outlet port, SAE flange (code 61) SAE J518c 3/4in
Fixing thread ISO 68 3/8-16UNC-2B; 0.75 (19) deep 31 lb-ft (42 Nm)
S Inlet port, SAE flange (code 61) SAE J518c 1 1/4in
Fixing thread DIN 13 7/16-14UNC-2B; 0.79 (20) deep 48 lb-ft (66 Nm)
L/L1,2 Case drain ports (L1,2 plugged) ISO 11926 3/4-16UNF-2B 116 lb-ft (160 Nm)
X Pilot pressure port ISO 11926 7/16-20UNF-2B; 0.45 (11.5 deep) 29 lb-ft (40 Nm)
1) see general information
20/44 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 703/11.07
3.54 (90)
4.86 (123.5)
L
0.56 (14.3)
L
4.0000 DIA (ø101.6 )
h8
9)
Y
(6
72
2.60 (66)
2.
2.87 (73)
3.9979
L1
(47.6)
1.87
S B
S B
1.30 1.30 1.19 (30.2) 0.87 (22.2)
(33) (33) 1.30 1.30
Location of service ports for left hand rotation; turn port plate 180° (33) (33)
Shaft ends
S Spline shaft R Spline shaft K Parallel keyed shaft
7/8 in 13T 16/32DP1) 7/8 in 13T 16/32DP1) 0.251 (6.35 +0.025)
(SAE J744 - 22-4 (B)) (SAE J744 - 22-4 (B)) 0.10 1.13 0.250
(2.5) (28.6)
(25 -0.2 )
DIA 0.8742 (ø22.225 -0,02)
1/4-20UNC-2B
1/4-20UNC-2B
0.9843
0.9764
1/4-20UNC-2B
ø7/8 in
ø7/8 in
0.63
(16)
0.8750
4.86 (123.5)
X
L
0.55 (14.3)
L
3.9979 DIA (ø101.6h8)
5)
8.
2.31 (58.7)
(6
Y
1.26 (ø32)
70
2.
4.0000
2.60 (66)
2.87 (73)
S
4.21 (107)
Ansicht Z
1.87 (47.6)
0.79 (ø20)
B Z
S
B
0.87 (22.2)
Location of service ports for left hand rotation; turn port plate 180°
Shaft ends
C Tapered2) 0.75
DIA 0.749
(19)
(19.024)
(3-0,2) 0.251(6.35+0.025)
0.250
A
— 0.006 ) DIA 0.863
0.251(6.35+0.025)
(21.91)
0.130(3.2+0.1)
B
0.250
0.126
0.16 (4)
(21.774 +0.006
0.57
DIA 0.8575
0.8570
(14.4)
2.19 (55.6)
Taper
125:1000
9.09 (231)
5.49 (139.5)
3.54 (90)
L1
L1
5.12 (130)
0.37 (9.5) 1.14 X
4.76 (121)
0.25 (6.3) (29)
X
3.23 (82)
101-2(B) )
L
L
DIA 4.0000 (ø101.6 h8)
45°
(7 .91
2
4)
W
3.9979
2.59 (75)
(7 .91
45°
2
4)
0
0.47 (12) (3 .12 L2
)
3.54 (90) 5.75 (146)
6.69 (170)
6.77 (172)
4.49 (114)
1.87 (47.6)
DIA 0.79
DIA 1.26
(ø20)
(58.7)
(ø32)
2.31
S B
Ports
Tightening torque, max.1)
B Outlet port, SAE flange (code 61) SAE J518c 3/4in
Fixing thread ISO 68 3/8-16UNC-2B; 0.75 (19) deep 31 lb-ft (42 Nm)
S Inlet port, SAE flange (code 61) SAE J518c 1 1/4in
Fixing thread ISO 68 7/16-14UNC-2B; 0.79 (20) deep 48 lb-ft (66 Nm)
L/L1 Case drain ports (L1 plugged) ISO 11926 3/4-16UNF-2B 116 lb-ft (160 Nm)
X Pilot pressure port ISO 11926 7/16-20UNF-2B; 0.45 (11.5) deep 29 lb-ft (40 Nm)
1)see general information
RA 92 703/11.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. 23/44
9.09 (231)
5.49 (139.5)
3.54 (90)
0.37 (9.5) 1.14 L1 L1
5.12 (130)
(29) X
0.25 (6.3)
4.74 (120.5)
X
3.23 (82)
L L
(ø101.6 h8)
45°
(7 .91
2
4)
(ø32)
Z
(58.7)
1.26
2.31
4.0000
3.9979
(7 .91
2.95 (75)
45°
2
4)
S
DIA
0
0.47 (12) (3 .12 L2
1.19 )
3.54 (90) (30.2) 5.75 (146)
6.30 (160) 6.77 (172)
7.36 (187)
View Y 2.48
port plate 62 (63) X
right hand rotation
4.49 (114)
View Z
DIA 0.79
(47.6)
(ø20)
V
1.87
B
S
B
0.87
(22.2)
2.60 (66) 2.60 (66)
Location of service ports for left hand rotation; turn port plate 180°
Ports
Tightening torque, max.1)
B Outlet port, SAE flange (code 61) SAE J518c 3/4in
Fixing thread ISO 68 3/8-16UNC-2B; 0.75 (19) deep 31 lb-ft (42 Nm)
S Inlet port, SAE flange (code 61) SAE J518c 1 1/4in
Fixing thread ISO 68 7/16-14UNC-2B; 0.79 (20) deep 48 lb-ft (66 Nm)
L/L1 Case drain ports (L1 plugged) ISO 11926 3/4-16UNF-2B 116 lb-ft (160 Nm)
X Pilot pressure port ISO 11926 7/16-20UNF-2B; 0.45 (11.5) deep 29 lb-ft (40 Nm)
1) see general information
24/44 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 703/11.07
3.90 (99)
0.37 (9.5) 0.47 (12)
0.25 (6.3) 1.18 (30) 45°
5.18 (131.5)
Flange SAE J744 L1
101-2 (B) L
0.56 (14.3)
L
3.9979 DIA (ø101.6h8)
3.03 (77)
8)
Y
(7
07
2.70 (68.5)
3.
4.0000
View Y View Y
port plate 64 port plate 61
right hand rotation right hand rotation
.9 )
69
(ø38)
1.50
.4)
2.
S B S B
1.50 1.50 1. 1.0
(35 41 (26 3
(38) (38) .7) 3 0° .2) 30°
Location of service ports for left hand rotation; turn port plate 180° 1.50 1.50
(38) (38)
Shaft ends
S Spline shaft R Spline shaft U Spline shaft W Spline shaft
1 in 15T 16/32DP1) 1in 15T 16/32DP1) 7/8 in 13T 16/32DP1) 7/8 in 13T 16/32DP1)
(SAE J744 - 25-4 (B-B)) (SAE J744 - 25-4 (B-B)) (SAE J744 - 22-4 (B)) (SAE J744 - 22-4 (B))
1/4-20UNC-2B
1/4-20UNC-2B
1/4-20UNC-2B
1/4-20UNC-2B
ø7/8in
ø7/8in
ø1in
ø1in
L1
5.18 (131.5)
S
3.03 (77)
L
0.56 (14.3)
4.0000 DIA (ø101.6 )
h8
1.50 (ø38)
2.75 (69.9)
78
Y
2.70 (68.5)
3.9979
4.53 (115)
View Z
2.06 (52.4)
0.98 (ø25)
Z
S B
Location of service ports for left hand rotation; 1.03 3.54 (90) 3.54 (90)
turn port plate 180° (26.2)
Shaft ends
K Shaft C Tapered shaft (ISO 3019-1 - 25-3)2)
DIA 1in 0.84(21.41)
A
-0,2
3/4-16UNF-2B
0.251(6.35+0.025)
1/4-20UNC-2B
(25.4)
1.0000
0.130 (3.2+0.1)
1.1024
0.63 B
0.250
0.126
(16)
0.56 0.12 (3)
0.99(25.16)
9.25 (235)
5.75 (146)
3.90 (99)
0.37 (9.5) 1.22 (31) L1
Flange
0.25 (6.3)
SAE J744
L
5.24 (133)
101-2 (B)
4.84 (123)
0.1
2
3.27 (83)
(3
0.56 (14.3)
3.9979 DIA (Ø101.6h8)
)
45°
7)
(7
5)
Y
5.
03
(7
3.
97
45°
4.0000
2.
3.62 (92)
0.1
0.47 (12) L2 2
(3
3.90 (99) )
7.44 (189) 5.75 (146)
6.77 (172)
2.68 (68)
View Y
port plate 61 X
right hand rotation
4.57 (116)
9)
1.50 DIA (ø38) (69.
.4)
2.
S B
1.
(35 41 1.0
3 3 0°
.7) 30° (26.
2)
1.50 1.50
(38) (38)
Location of service ports for left hand rotation; turn port plate 180°
Shaft ends see page 24, 25
Ports
Tightening torque, max.1)
B Outlet port, SAE flange (code 61) SAE J518c 1in
Fixing thread ISO 68 3/8-16UNC-2B; 0.71 (18) deep 31 lb-ft (42 Nm)
S Inlet port, SAE flange (code 61) SAE J518c 1 1/2in
Fixing thread ISO 68 1/2-13UNC-2B; 0.87 (22) deep 65 lb-ft (90 Nm)
L/L1 Case drain ports (L1 plugged) ISO 11926 7/8-14UNF-2B 174 lb-ft (240 Nm)
X Pilot pressure port ISO 11926 7/16-20UNF-2B; 0.45 (11.5) deep 29 lb-ft (40 Nm)
1) see general information
RA 92 703/11.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. 27/44
9.25 (235)
5.75 (146)
3.90 (99)
0.37 (9.5) 1.22 (31) L1
0.25 (6.3)
Flange L1 X L
5.24 (133)
SAE J744
4.84 (123)
101-2 (B)
0.
S
08
3.27 (83)
3.9979 DIA (Ø101.6h8)
(2
1.50 (Ø38)
)
45°
14.3
2.75 (69.9)
7)
(7
5)
03
5.
Y
(7
3.
97
45°
2.
4.0000
3.62 (92)
0.1
L2 2
0.47 (12) 1.41 (3
)
3.90 (99) (35.7) 5.75 (146)
7.00 (178) 6.77 (172)
8.31 (211)
4.57 (116)
View Z
2.06 (52.4)
0.98 (ø25)
Z
S
B
B
Location of service ports for left hand rotation; turn port plate 180°
5.39 (137)
L1
Flange SAE J744
101-2 (B) L
S
3.42 (87)
L
0.56 (14.3)
3.9979 DIA (ø101.6h8)
5)
3.06 (77.8)
1.97 (ø50)
8.
Y
(7
09
3.
4.0000
2.99 (76)
1.69
(42.9)
7.93 (201.5) 5.75 (146)
9.43 (239.5) 6.77 (172)
View Y
port plate 62
right hand rotation
View Z
2.06 (52.4)
0.98 (ø25)
Z
S B
B 1.11
(26.2)
Shaft ends
S Spline shaft R Spline shaft U Spline shaft W Spline shaft
1 1/4 in 14T 12/24DP1) 1 1/4 in 14T 12/24DP1) 1 in 15T 16/32DP1) 1 in 15T 16/32DP1)
(SAE J744 - 32-4 (C)) (SAE J744 - 32-4 (C)) (SAE J744 - 25-4 (B-B)) (SAE J744 - 25-4 (B-B))
5/16-18UNC-2B
5/16-18UNC-2B
1/4-20UNC-2B
1/4-20UNC-2B
ø1 1/4 in
ø1 1/4 in
ø1 in
ø1 in
0.75
0.75 (19) 0.63 (16) 0.63 (16)
(19)
1.50 1.14
1.56 (38) 0.98 (29)
(39.5) (25)
2.18 (55.4) 1.81 (45.9)
2.18 (55.4) 1.81 (45.9)
Ports
Tightening torque, max.2)
B Outlet port, SAE flange (code 61) SAE J518c 1in
Fixing thread ISO 68 3/8-16UNC-2B; 0.71 (18) deep 31 lb-ft (42 Nm)
S Inlet port, SAE flange (code 61) SAE J518c 2in
Fixing thread ISO 68 1/2-13UNC-2B; 0.87 (22) deep 65 lb-ft (90 Nm)
L/L1 Case drain ports (L1 plugged) ISO 11926 7/8-14UNF-2B 174 lb-ft (240 Nm)
1) ANSI B92.1a-1996, 30° pressure angle, flat root, side fit, tolerance class 5
2) see general information
RA 92 703/11.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. 29/44
5.93 (137)
127-4 (C)
0. 4.3
(1
56 )
3.43 (87)
L
(ø127h8)
5)
4.51 (114.5)
5.83 (148)
8.
(7
Y
5.0000 DIA
09
3.
2.99 (76)
4.9975
4.74 (120.5)
right hand rotation
3.06 (77.8)
1.97 (ø50)
(ø25)
0.98
2.06 (52.4)
B
S
1.67 (42.9) 1.03 (26.2)
1.30 (33) 1.81 (46)
Location of service ports for left hand rotation; turn port plate 180°
Shaft ends
K Parallel keyed shaft C Tapered (ISO 3019-1 - 25-3)2)
0.3136 0.13 1.16 Section A-B
0.3126 (7.94 )
+0,025
(35.3-0,2)
A
3/4-16UNF-2B
0.3136(7.94+0.025)
DIA 1.25
(31.75)
0.1394(3.54—0.1)
(25.4)
5/16-18UNC-2B
1.3898
1.3819
B
0.3126
1.2500
0.75
0.1354
1.18 Taper
0.31 (7.9) (30) 125:1000
0.93 1.37
2.18 (55.4) (23.6) (34.9)
2.61 (66.4)
Ports
Tightening torques, max.1)
B Outlet port, SAE flange (code 61) SAE J518c 1in
Fixing thread ISO 68 3/8-16UNC-2B; 0.71 (18) deep 31 lb-ft (42 Nm)
S Inlet port, SAE flange (code 61) SAE J518c 2in
Fixing thread ISO 68 1/2-13UNC-2B; 0.87 (22) deep 65 lb-ft (90 Nm)
L/L1 Case drain ports (L1 plugged) ISO 11926 7/8-14UNF-2B 174 lb-ft (240 Nm)
X Pilot pressure port ISO 11926 7/16-20UNF-2B; 0.45 (11.5) deep 29 lb-ft (40 Nm)
1) see general information 2) only series 52
30/44 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 703/11.07
9.72 (247)
5.93 (150.5) Mounting flange „D“
4.55 (115.5)
0.5 (12.7) 1.54 (39) L1
6.3 X L1
(14 55
L
0.
)
5.04 (128)
5.51 (140)
Flange SAE J744
127-4 (C)
43 °
3.50 (89)
4.9975 DIA (ø127h8)
45° 45°
4.51 (114.5)
5.75 (146)
9)
(7
Y
1
)
7.5
3.1
(7
5.0000
3.46 (88)
05
45°
3.
L2
0.59 (15)
4.55 (115.5) 4.51 (114.5)
8.19 (208) 5.91 (150)
2.56 (65)
View Y X
port plate 61
right hand rotation
4.88 (124)
2.06 (52.4)
0.98 (ø25)
3.06 (77.8)
1.97 (ø50)
S B
Ports
Tightening torque, max.1)
B Outlet port, SAE flange (code 61) SAE J518c 1in
Fixing thread ISO 68 3/8-16UNC-2B; 0.71 (18) deep 31 lb-ft (42 Nm)
S Inlet port, SAE flange (code 61) SAE J518c 2in
Fixing thread ISO 68 1/2-13UNC-2B; 0.87 (22) deep 65 lb-ft (90 Nm)
L/L1 Case drain ports (L1 plugged) ISO 11926 7/8-14UNF-2B 174 lb-ft (240 Nm)
X Pilot pressure port ISO 11926 7/16-20UNF-2B; 0.45 (11.5) deep 29 lb-ft (40 Nm)
1) see general information
RA 92 703/11.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. 31/44
9.72 (247)
5.91 (150) Mounting flange „C“
4.55 (115.5)
5.51 (140)
5.04 (128)
Flange SAE J744
101-2 (B)
L
3.50 (89)
43°
0.56 (14.3)
L
4.0000 DIA (ø101.6 )
h8
(7 .11
3.06 (77.8)
1.97 (ø50)
9)
3
Y
(7 .05
)
3.9979
7.5
3
45°
3.46 (88)
S
2.56 (65)
View Y
port plate 62 X
right hand rotation
4.88 (124)
View Z
2.06 (52.4)
0.98 (ø25)
Z
B
S
1.03 (26.2)
Location of service ports for left hand rotation; turn port plate 180°
Ports
Tightening torque, max.1)
B Outlet port, SAE flange (code 61) SAE J518c 1in
Fixing thread ISO 68 3/8-16UNC-2B; 0.71 (18) deep 31 lb-ft (42 Nm)
S Inlet port, SAE flange (code 61) SAE J518c 2in
Fixing thread ISO 68 1/2-13UNC-2B; 0.87 (22) deep 65 lb-ft (90 Nm)
L/L1 Case drain ports (L1 plugged) ISO 11926 7/8-14UNF-2B 174 lb-ft (240 Nm)
X Pilot pressure port ISO 11926 7/16-20UNF-2B; 0.45 (11.5) deep 29 lb-ft (40 Nm)
1) see general information
32/44 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 703/11.07
6.12 (155.5)
127-2 (C)
L
0.69 (17.5)
3.68 (93.5)
L
5.0000 DIA (ø127 )
h8
5)
(9
Y
74
3.
3.46 (88)
4.9975
66.7
ø32
S B
1.97 1.77
(50) (45)
2.00 (50.8) 1.25 (31.8)
Location of service ports for left hand rotation; turn port plate 180° 3.62 (92) 3.11 (79)
Shaft ends
S Spline shaft U Spline shaft W Spline shaft
1 1/2 in 17T 12/24DP 1) 1 1/4 in 14T 12/24DP 1) 1 1/4 in 14T 12/24DP 1)
(SAE J744 - 38-4 (C-C)) (SAE J744 - 32-4 (C)) (SAE J744 - 32-4 (C))
5/16-18UNC-2B
5/16-18UNC-2B
7/16-14UNC-2B
ø1 1/4 in
ø1 1/4 in
ø1 1/2 in
Ports
Tightening torque, max.2)
B Outlet port, SAE flange (code 62) SAE J518c 1 1/4in
Fixing thread ISO 68 1/2-13UNC-2B; 0.75 (19) deep 65 lb-ft (90 Nm)
S Inlet port, SAE flange (code 61) SAE J518c 2 1/2in
Fixing thread ISO 68 1/2-13UNC-2B; 1.07 (27) deep 65 lb-ft (90) Nm
L/L1 Case drain ports (L1 plugged) ISO 11926 1 1/16-12UN-2B 260 lb-ft (360 Nm)
1) ANSI B92.1a-1996, 30° pressure angle, flat root, side fit, tolerance class 5
2) see general information
RA 92 703/11.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. 33/44
6.12 (155.5)
127-2 (C) S
L
3.68 (93.5)
L
0.69 (17.5)
(ø127h8)
5)
3.5 (88.9)
(9
Y
75
5.0000 DIA
3.
3.46 (88)
4.9975
2.00
(50.8) 6.22 (158)
9.27 (235.5) 7.13 (181)
10.90 (276.8) 8.27 (210)
View Y 2.91 (74) 0.45 (11.5)
port plate 62 X
right hand rotation
5.47 (139)
View Z
B
2.63 (66.7)
1.26 (ø32)
Z
S B
1.25
(31.8)
3.74 (95) 3.35 (85)
Location of service ports for left hand rotation; turn port plate 180°
Ports
Tightening torque, max.1)
B Outlet port, SAE flange (code 62) SAE J518c 1 1/4in
Fixing thread ISO 68 1/2-13UNC-2B; 0.75 (19) deep 65 lb-ft (90 Nm)
S Inlet port, SAE flange (code 61) SAE J518c 2 1/2in
Fixing thread ISO 68 1/2-13UNC-2B; 1.07 (27) deep 65 lb-ft (90) Nm
L/L1 Case drain ports (L1 plugged) ISO 11926 1 1/16-12UN-2B 260 lb-ft (360 Nm)
X Pilot pressure port ISO 11926 7/16-20UNF-2B 0.45 (11,5) deep 29 lb-ft (40) Nm
1) see general information
34/44 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 703/11.07
10.75 (273)
7.15 (181.5)
5.63 (143)
0.50 (12.7) 1.42 (36)
X L1
0.40 (10.2) L1
X
5.71 (145)
5.91 (150)
FlangeSAE J744
0.1 4)
127-2 (C)
3.98 (101)
6
(
L
4.9975 DIA (ø127h8)
45° L
(9 .74
5)
3
Y
4
3.7 5)
4.04 (102.5)
0.69 (17.5)
5.0000
(9
45°
0.1 4)
0.79 (20) L2
6
(
5.12 (130) 7.13 (181)
9.65 (245)
8.27 (210)
2.91 (74) X
View Y
port plate 61
right hand rotation
2.63 (66.7)
5.24 (133)
1.26 (ø32)
3.50 (88.9)
2.36 (ø60)
B
S
2.00
(50.8) 1.25 (31.8)
1.97 (50) 1.77 (45)
Location of service ports for left hand rotation; turn port plate 180°
Ports
Tightening torque, max.1)
B Outlet port, SAE flange (code 62) SAE J518c 1 1/4in
Fixing thread ISO 68 1/2-13UNC-2B; 0.75 (19) deep 65 lb-ft (90 Nm)
S Inlet port, SAE flange (code 61) SAE J518c 2 1/2in
Fixing thread ISO 68 1/2-13UNC-2B; 1.07 (27) deep 65 lb-ft (90 Nm)
L/L1/2 Case drain ports (L1/2 plugged) ISO 11926 1 1/16-12UN-2B 360 Nm
X Pilot pressure port ISO 11926 7/16-20UNF-2B; 0.45 (11.5) deep 29 lb-ft (40 Nm)
1) see general information
RA 92 703/11.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. 35/44
10.75 (273)
7.15 (181.5)
5.63 (143)
X
L1
0.50 (12.7) 1.42
(36)
L1
0.40 (10.2)
Flange SAE J744 X
5.91 (150)
5.71 (145)
0.1
127-2 (C)
6
L
(4
L
)
5.0000 DIA (ø127 )
45°
4
3.7 5)
3.50 (88.9)
2.48 (ø63)
Y (9
4
3.7 5)
0.69 (17.5)
4.9975
(9
45°
S
2.00
0.1 4)
0.79 (20) L2
6
(
5.12 (130) (50.8) 7.13 (181)
9.27 (235.5)
8.27 (210)
10.91 (277)
2.91 (74)
View Y X
port plate 62
right hand roation
5.24 (133)
View Z
1.26 DIA (ø32)
2.63 (66.7)
Z
S
B
B
1.25 (31.8)
Location of service ports for left hand rotation; turn port plate 180°
Ports
Tightening torque, max.1)
B Outlet port, SAE flange (code 62) SAE J518c 1 1/4in
Fixing thread ISO 68 1/2-13UNC-2B; 0.75 (19) deep 65 lb-ft (90 Nm)
S Inlet port, SAE flange (code 61) SAE J518c 2 1/2in
Fixing thread ISO 68 1/2-13UNC-2B; 1.07 (27) deep 65 lb-ft (90 Nm)
L/L1/2 Case drain ports (L1/2 plugged) ISO 11926 1 1/16-12UN-2B 360 Nm
X Pilot pressure port ISO 11926 7/16-20UNF-2B; 0.45 (11.5) deep 29 lb-ft (40 Nm)
1) see general information
36/44 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 703/11.07
Size 10 18 28 45 63 85
Permissible overhang moment
static Tm lb-ft – – 656 664 1010 2270
(Nm) (890) (900) (1370) (3080)
dynamic at 10 g Tm lb-ft – 65 66 101 227
(322 ft/sec2(9,81 m/s2)) (Nm) (89) (90) (137) (308)
Weight m1 lbs 18 25 31 40 48.5 75
(kg) (8) 11,5 (14) (18) (22) (34)
Distance to center of gravity l1 in – – 3.19 3.74 3.94 4.8
(mm) (81) (95) (100) (122)
m1, m2 Weight of pumps [lbs (kg)]
l1, l2 Dist. to center of gravity [in (mm)]
m1 m2 1
(Tm = (m1 • l1 + m2 • l2) • [lb-ft (Nm)])
12 (102)
l1
l2
SectionA-B Size A1 A3 A4 A5
A4
not on size 28 A3 28 8.03 0.39 1.85 M10; 0.63
(204) (9.9) (47) (16) deep
45 9.02 0.42 2.09 M10; 0.63
45°
(229) (10.7) (53) (16) deep
(ø82.55 +0.020 )
+0.050
A B
3.2520 DIA
63 10.04 0.37 2.32 M10; 0.63
4.19
3.2508
(106 (255) (9.5) (59) (16) deep
.5)
85 11.89 0.53 2.68 M10; 0.63
A5 (302) (13.4) (68) (16) deep
0.39 (10)
not on size 28 to pump mounting face A1
A B
63 10.04 1.55 0.74 2.40 M10; 0.63
3.2508
4
(ø .19 (255) (39.4) (18.9) (61) (16) deep
106
.5) 85 11.89 1.74 0.93 2.56 M10; 0.63
A5 (302) (44.1) (23.6) (65) (16) deep
0.39 (10)
not on size 28 A2
to pump mounting face A1
0.39 (10)
not on size 28 and 45
A2
to pump mounting face A1
1) 30° pressure angle, flat root, side fit, tolerance class 5
38/44 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 703/11.07
Section
CoupeA-BA-B Size A1 A2 A3 A4 A5
non on
not avec
sizecal.
4545 A4
45 9.02 1.88 0.74 2.10 M12; 0.71
A3
(229) (47.9) (18.9) (53.4) (18) deep
63 10.04 1.86 0.72 2.32 M12; 071
45°
(255) (47.4) (18.4) (58.9) (18) deep
A B
+0.020 )
(ø101.6+0.050
85 11.89 2.01 0.87 2.71 M12; 0.79
ø101.6 DIA
5.7 (302) (51.2) (22.2) (69) (20) deep
5
ø101.6
(14
6)
A5
non on
not avec
sizecal.
4545 0.39 (10)
A2
jusqu‘au
to pump flasque
mounting facedeAmontage
1
+0.050
5.0008
7.13 )
1
(ø18
5.0008
A5
B
0.51 (13)
to pumpjusqu‘au flasque
mounting face de
A1 montage
(ø127 +0.020 )
5.0020 DIA
+0.050
7.13 )
1
(ø18
5.0008
A5
B
0.51 (13)
jusqu‘au
to pump flasqueface
mounting de montage
A1
1) 30° pressure angle, flat root, side fit, tolerance class 5
40/44 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 703/11.07
Before installation fill pump housing, keeping it in a horizontal Arrangement inside the reservoir
position.
a) If the min. fluid level is equal to or above the pump mounting a) If the min. fluid level is above the top of the pump: plug port
face: plug port "L" , "L1" and "S" open; it is recommended to "L1" , "L" and "S" open; it is recommended to pipe "L“ and
pipe "L1" and connect a suction pipe to "S" (see fig. 1). connect a suction pipe to "S“ (see fig. 3).
b) If the min. fluid level is below the pump mounting face: pipe b) If the min. fluid level is below the top of the pump: pipe "L"
ports "L1" and „S" acc. to fig. 2 "L" plugged. (see also limit of and "S" acc. to fig. 4, "L1" plugged (see also limit of condi-
conditions) tions).
Note: to avoid pump damage, remove all protective parts (dust Note: to avoid pump damage, remove all protective parts (dust
covers, plastic plugs etc.) before installation. covers, plastic plugs, etc) before installation.
Fluid
min. 7.87 in (200 mm)
Fluid L
L1
L S
ht min
L1 Fig. 3
min. 7.87 in S
(200 mm) Fig. 1
Arrangement outside the reservoir
Above the reservoir as in fig. 2. Before installation fill pump Pipe port "S" and the highest of the case drain ports "L", "L1"
housing, keeping it in a horizontal position. or "L2“ .
a) Mounting above the tank: see fig. 4. (see also "Limit of
Limit of conditions conditions“)
Min. pump inlet pressure pabs min = 12 psi (0,8 bar) under static
and dynamic conditions. L1 S
Note: try to avoid mounting above tank in order to obtain a low
L
ht min hmax
Fluid
Baffle Fig. 2
ht min
L Fig. 5
RA 92 703/11.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. 41/44
Notes
42/44 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 703/11.07
Notes
RA 92 703/11.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. 43/44
Notes
44/44 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 703/11.07
General information
– The A10VO pump is designed to be used in open circuits.
– Project planning, assembly and commissioning of the pump require the involvement of qualified personnel.
– The service line ports and function ports are only designed to accommodate hydraulic lines.
– During and shortly after operation, there is a risk of burns on the pump and especially on the solenoids. Take suitable safety
precautions, e.g. wear protective clothing
– There may be shifts in the characteristic depending on the operating state of the pump (operating pressure, fluid temperature).
– Tightening torques:
- The tightening torques specified in this data sheet are maximum values and must not be exceeded
(maximum values for screw thread).
Manufacturer´s instruction for the max. permissible tightening torques of the used fittings must be observed!
- For DIN 13 fixing screws, we recommend checking the tightening torque individually according to VDI 2230 Edition 2003.
– The data and information contained herein must be adhered to.
Bosch Rexroth Corporation Bosch Rexroth Corporation © This document, as well as the data, specifications and other information set
Mobile Hydraulics Industrial Hydraulics forth in it, are the exclusive property of Bosch Rexroth AG. It may not be repro-
Axial & Radial Piston Units 2315 City Line Road duced or given to third parties without its consent.
8 Southchase Court Bethlehem, PA 18017-2131 The data specified above only serve to describe the product. No statements
Fountain Inn, SC 29644-9018 USA concerning a certain condition or suitability for a certain application can be de-
USA Telephone (610) 694-8300 rived from our information. The information given does not release the user from
Telephone (864) 967-2777 Facsimile (610) 694-8467 the obligation of own judgment and verification. It must be remembered that our
products are subject to a natural process of wear and aging.
Facsimile (864) 967-8900 www.boschrexroth-us.com
www.boschrexroth-us.com Subject to change.