Protection Transmission and Distribution
Communication Channels As The Weakest Link In The System
Protection Chain
Secure & Dependable Protection
Protection engineers have a variety of communication channels to use for relay protection. This is a field in
itself, and is very important for a discussion of the protective systems. Historically and currently, channels
generally have been the weakest link in the protection chain.ammunication Channels As The
/eakest Link In The System Protection Chain (on photo: El
line aps and optical er cable)
ity pylon with
‘Tremendous progress has been made from the early applications in the 1930s to the quite sophisticated
and highly reliable equipment available in recent times. This is a specialized field, and applications for
protection should be made by specialists in this area, who are familiar with the protection requirements.Contents:
4. Power-Line Carrier: On-Off or Frequeney-Shift
2. Pilot Wires ~ Audio Tone Transmission
3. Pilot Wires ~ 50 Hz Or 60 Hz Transmission
4, Digital Channels
5. Summary
‘1. Power-Line Carrier — On-Off or Frequency-Shift
Beginning in the early 1930s radio frequencies between 50 and 150 kHz were superimposed on the power
lines for pilot protection. They were originally used in an on-off mode and, as the art progressed,
frequency-shift became available.
‘These are known as power-line carrier channels (PLCC) and are in wide use with frequencies between
30 and 300 kHz. Figure 1 illustrates a typical channel of this type.
In the United States, phase-to-ground coupling is most commonly used. Other types used are
phase-to-phase, two-phase-to-ground, and so on. The transmitters generate about 1-10 W of
radiofrequency (RF) power.normally mounted at the base of the coupling capacitor unit, cancels the capacitance of the coupling
capacitor unit.
This provides essentially a low-impedance resistive path for efficient transfer of RF signals to and from the
line sectionbus trap trap bus
—, oR
Re Line Re
THH
Relays 4 3 k- Relays
yy Bau
RF Line Coupling
transmitter tuner capacitor
receiver with optional
voltage device
(ccvT)
jure + Typlealsinglo-ne dagramn ora paso-to-ground power-tne cs
Re ow
Coupling line RF
capacitor tuner transmitter—
with optional receiver
voltage device
(ccvT)
rr chanelfrequency tuner
The inductance between the coupling capacitor and ground presents a high impedance to the RF signal,
but low impedance to the system 50 or 60 Hz. This unit may also supply secondary voltage as Coupling
capacitor voltage devices (CCVTS), in which case, three are used to connect individual phases, and only
one is used for coupling, as shown
Aline trap is connected in the high-voltage line at each terminal just external to the RF path. It is tuned to
provide a high RF impedance, to minimize signal loss into the buses and associated systems, and to
prevent external ground faults from potentially shorting out the signal.
Traps are available for tuning to a single frequency, double (two) frequencies, or to a broad band of RF
frequencies. They are designed to carry a 50 to 60 Hz-load current continuously at low loss, and to
withstand the maximum fault current that can pass through the line.Coupling _|
Capacitor 7
Toning
Elements
Figure 2 ~ Single Phase-to-Ground (Center Phase) Coupling
Although the RF signal is introduced to one of the phases, it is propagated by all three-phase conductors.
There have been several occasions when the accidental coupling to different phases at the two terminals
has gone unnoticed for several years because an adequate signal was received
In fact, the signal may be greater when coupled to different phases.predicting carrier performance and the best method of coupling and
transmission. This is important, especially for long lines.
Overhead power lines tend to have a characteristic impedance (Zp) between 200 and 500 V phase-to-
ground and 400-488 V between phases. The carrier equipment and coupling particularly match these
values for maximum power transfer of the RF.
Taps and discontinuities, particularly if they are at quarter wavelengths, can result in high signal losses.
The RF signals should be selected to avoid these problems.
Power-line carrier applications to power cables may be impossible or very difficult, as their
characteristic impedance is low and the losses are higher than that for overhead lines.
Carrier transmitter-receivers are operated on-off, frequency-shift with mark-space signals, or single
sideband, depending on the design and application.
Fault arc noise has not been a problem or a significant factor in the use of power-line carrier for
protection. Disconnect switches with currents less than 200 A can cause operation of carrier on-off
receivers, but this does not impair the protection used with this type of equipment
More Information: Power-Line Carrier Channel & Application Considerations For Transmission Line
RelayingGo back to contents 7
2, Pilot Wires — Audio Tone Transmission
Audio tones in the range of 1000-3000 Hz are used for protection. They are more compatible for use
over leased telephone facilities and, therefore, they are frequently applied over these channels for
protection.
he protection hazards and solutions outlined earlier are applicable. When used, neutralizing transformers
should be able to pass the audio-frequencies with low losses.
Frequency-shift, on-off, and pulse-code equipment is available.Go back to contents 1
3. Pilot Wires - 50 Hz Or 60 Hz Transmission
One of the early and stil used channels is a twisted pair of “telephone” wires to provide a low-voltage,
low-power continuous circuit between the protected zone terminals.
Preferably, wires on the order of AWG 19 are desired both for mechanical strength and to provide loop
that is not more than about a 2000 V for two terminals or not more than 500 V per leg for three-terminal
applications.the pair from signals on other pairs in the cable and from external voltages outside the cable
The problems that are experienced with pilot wires result from induction from lightning or a paralleled
power circuit, insulation stress from a rise in station ground-mal voltage during faults, direct physical
contact by lightning or with the power circuit, physical damage by insulation failure, or gunfire directed at
overhead circuits
Go back to contents 1
4, Digital Channels
In recent years, digital channels are increasingly used for pilot relaying communications. Some of the types
of digital channels that are used for this function include:
+ Dark fiber (dedicated fiber-optic cable),
+ Multiplexed fiberoptic systems (T1 and SONET),
* Digital microwave,
+ Radio links, and
+ 56 kbps phone lines (Digital Data Service)
Digital microwave can be point-to-point or used within a SONET ring. Digital communication systems are a
study in themselves and are beyond the scope of this article.High Speed
‘SONET Ring
Collector Ring Collector Ring
Figure 3 - The most popular method (and the most expensive) isto implement
‘SONET in a series of interconnected rings, as shown below (the SONET Network
the cloud... contains interconnected rings that span the USA), The rings themeoWes
are comprised of 4 b-eirectonal fibers ~ one primary pair of vansmitreceive and
‘on secondary (backup) pai of transmitreceive
Itis important, however, for protection engineers to become familiar with this area as digital communication
systems continually play a large role in modern protective systems.for protection and control is replaced in many cases with digital
communication systems with the application of microprocessor based
relaying. Practically all modern microprocessor relays have built-in
digital communication capability and ports for sending and
receiving digital messages.
With respect to pilot relay systems, the optimal digital channel performance can be obtained from a
dedicated fiber pair. The dedicated pair is virtually immune from electrical interference, has a very low bit
error rate, and a very short end-to-end data delay time.
Such application, however, is very expensive and can be prone to long outages if the fiber is cut.
Multiplexed digital networked systems offer the advantage of very low outage rates. In such systems, if
a path is lost, an alternate route is automatically and quickly inserted. Such systems are also more
economical than dark fiber because up to 24 channels can be multiplexed on a single fiber pair.
Delay times and time to switch over to an alternate path need to be considered when applying
multiplexed digital communication systems. The normal magnitudes of delay and switchover times
involved, however, usually do not prevent the use of multiplexed communication systems in pilot
schemes that use digital relays.‘A concern with using digital microwave is its tendency to fade during inclement weather conditions — it
is during these types of conditions that faults are most likely to occur on the power system!
‘Some of the important parameters that need to be con:
systems in pilot relay schemes include the following:
jered when applying digital communication
1. Delay time from end-to-end
The pilot system must be capable of dealing with variations in delay times that exist in many digital
systems. A difference could exist between the delay time involved in sending a signal and that involved
with receiving a signal
Delay times can also change when alternate paths are inserted
2, Interruptions to the communication channel
The system must be designed to be capable of resynchronization following a switching operation on the
communication network.
3, Exessive bit errors.
High attenuation caused by long distances can result in bit error rates that are very high for obtaining
satisfactory operation of a pilot system. Moreover, copper links can exist within communication networks
resulting in the possibility of electrical interference.NOTE: — In such applications, channel delays less than 1 msec are desirable and channels with
delays more than 2 msec should not be considered.
Experience has shown that digital channels that are available from telephone companies through
channel service units (CSUs) are not suitable for protective relaying applications. As the CSU is,
not hardened for use within a substation, nearby faults can cause the channel to be lost.
Periodic interruptions, long delay times (greater than 20 msec), and asymmetrical delays are other
problems that have been encountered when attempted to apply such systems in relaying schemes.
Go back to contents 1
Summary
The channels used for protective relaying are as follows:
1, Pilot wires A twisted wire pair for transmitting 60, 50 Hz DC between terminals. Originally
telephone pairs were used, privately owned dedicated pairs are preferred.
2, Audio frequency tones — On-off or frequency-shift types over wire pairs, power-line carrier, or
microwave.
3. Power-line carrier — Radio frequencies between 30 and 300 kHz, transmitted chiefly over high-
voltage transmission lines, On-off or frequency-shift types are used,5. Digital Channel — Types of media include dedicated optical fiber (dark fiber) or multiplexed
networks. Multiplexed networks include T1 multiplexing, SONET, digital microwave, and radio
links.
When owned by the utility, fiber-optic cables can be imbedded
in the ground wire, wrapped around a power cable, or buried
along the right-of-way. Digital channels may also be leased from
an outside telecommunications company.
Go back to contents }
Power line carrier in power transmission line (VIDEO)Reference /! Protective Relaying Principles and Applications by J. Lewis Blackburn and Thomas J. Domin
(Purchase hardcopy from Amazon)ruvaru usanyt
Electrical engineer, programmer and founder of EP, Highly specialized for design of LV/MV switchgears
and LV high power busbar trunking (<6300A) in power substations, commercial buildings and industry
fascilities. Professional in AutoCAD programming. Present on Google+