Professional Documents
Culture Documents
Rotorclip Catalog (2012) PDF
Rotorclip Catalog (2012) PDF
ROTOR CLIP ®
Designed for Quality ®
Price: $2.00 U.S.
www.rotorclip.com
Rotor Clip Company, Inc.® - World Headquarters
187 Davidson Avenue, Somerset, NJ 08873
1-800-557-6867 • +1 732-469-7333 • Fax: +1 732-469-7898
e-mail: sales@rotorclip.com • www.rotorclip.com
E/SE/ RE BE C LC PO/POL EL
Page 50-51 Page 58-59 Page 52-53 Page 54-55 Page 56-57 Page 60-61
YE/ZE
Page 48-49
Axially Installed
Self-Locking, Inch Tapered Section Retaining Rings
External Internal
SHF RG TX TY TI
Page 62-63 Page 64 Page 65 Page 66 Page 67
2 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
Product Index
Inch Constant Section Retaining Rings
Internal External
DKR DKL KLM MKM MKR MKG MKA DCR DCL CLM MCM MCR MCG MCA
DIN 472 Page 182-183 Page 186-187 Page 190-191 Page 194-195 Page 198-199 Page 202-203 DIN 471 Page 184-185 Page 188-189 Page 192-193 Page 196-197 Page 200-201 Page 204-205
Page 176-179 Page 180-181
Wave Springs
Single Turn Multi Turn
Gap Overlap Gap Gap Overlap Shim Ends Plain Ends Shim Ends Plain Ends
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 3
Rotor Clip Your Single Source
All Rings Have A
Function...
A discussion of retaining rings must inevitably begin with a
debunking of myths; namely, that one style retaining ring will
function better than all other types in all instances. No one
retaining ring style is “better” than another. Rather, the
parameters of an application actually determine which
retaining ring is best to use, and this can vary from assembly
to assembly. Selecting the correct type of retaining ring based
on variables such as installation/removal requirements, The following are some points to take into consideration when
anticipated thrust load, and end play take-up can ensure the choosing a ring. Our engineers work with you to find the right
retaining ring you choose will perform reliably, while type of ring for your design.
significantly reducing fastener costs.
There are three main types of retaining rings available to the TAPERED SECTION
designer: tapered, constant section and spiral. These are Tapered section rings make
typically made from carbon steel, stainless steel or beryllium uniform contact with the
copper and feature a variety of finishes for corrosion groove, with a gap between
protection (see accompanying table). Again, the final selection the lugs.
of a type and size retaining rings depends upon these and the
previously mentioned parameters.
CONSTANT SECTION
Constant section rings are
elliptical when installed in the
groove, making only 3-point
contact as illustrated
SPIRAL RINGS
Spiral rings make 360°
contact with the groove
4 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
Ring Attributes
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 5
Part Numbers & Packaging
ROTOR CLIP PART NUMBER
HO-50 ST PA S
Identifies the TYPE of ring
Denotes PACKAGING
(Note: Bulk packaging has no code.
Not all ring types can be stacked)
6 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
rotorclip.com Online Ordering
DISCOUNT AVAILABLE
Place Your Order Online
As an added incentive to sign up, we’re offering all of our
and You May be Eligible non-contract customers a discount (2% for carbon steel,
1.5% for stainless steel) on all orders placed online in our
for a Discount standard box quantities.
Now you can. As a current/prospective customer, Rotor Clip “DOUBLE ENTRY” NOT A PROBLEM
invites you to take advantage of our online ordering system to
help you reduce your transaction costs and to make important No need to be concerned about “double entry”…having
information like order status, availability and quote status to enter the order into your system and ours. A simple
available to you when you want to see it. No need to make a conversation between our respective IT departments should
phone call or wait for a customer service person to lookup solve this issue, usually by arranging to transmit a flat file.
your information. It can be available to you 24/7 on your This eliminates the need to enter the order twice into our
computer. respective systems.
With Rotor Clip’s online ordering system you can check stock and availability as well as place your order. You can also check
the status of your order, submit, view or print quotes, and view and print invoices.
TO SIGN UP FOR ROTOR CLIP ONLINE ORDERING
CALL 1-800-557-6867 OR E-MAIL ADV@ROTORCLIP.COM
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 7
Materials Tapered/Constant Section Rings
Standard material for Rotor Clip retaining rings is carbon spring steel (SAE 1060-1090/UNS G10600-G10900). Rings can also be produced
in our standard stainless steel (PH 15-7 Mo/UNS S15700) with 420 type cold rolled stainless steel (UNS S42000) as an option and in our
standard beryllium copper (Alloy #25/UNS C17200) with copper alloy C72900 and phosphor bronze (Alloy#5218/UNS C52180) as options.
Please note that the availability of rings in the stainless steel and copper materials is subject to prior inquiry and acceptance of a formal
quotation.
Rotor Clip can also produce rings one gauge thicker or thinner than standard sizes. Again, such orders are subject to prior inquiry and
acceptance of a formal quotation.
CARBON SPRING STEEL - This steel is known for its high PHOSPHOR BRONZE ALLOY#5218 - The least expensive
strength, and reliability in retaining ring applications. Since copper material Rotor Clip offers. This type exhibits higher
carbon spring steel is subject to corrosion, Rotor Clip treats all strength compared to standard phosphor bronze materials
such rings with a protective coating to ensure some corrosion with the same tin percentages. It is also characterized by very
resistance. For long-term corrosion protection, a zinc plating good stress relaxation characteristics. (Note: Rotor Clip can
or non-metallic finish should be applied over the steel.(See also supply phosphor bronze material to DIN standard 17 662,
"Finishes" section). Material Number 2.1020. Contact Rotor Clip Technical Sales
for more information).
STAINLESS STEEL -
8 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
Tapered/Constant Section Rings Finishes
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 9
Materials/Finishes Spiral Rings
Materials: Finishes:
CARBON SPRING STEEL OIL DIP
This steel is known for its high strength and reliability in spiral This standard finish for carbon steel spiral retaining rings
ring applications. Since carbon steel is subject to corrosion, offers an extended shelf-life protection against rusting.
Rotor Clip rings are oil dipped to ensure some corrosion
resistance. BLACK OXIDE
This flat, black finish is used more for when aesthetics of the
STAINLESS STEEL - AISI 302 part are a factor with minimal corrosion protection.
This general purpose stainless steel offers corrosion
resistance and can be cold worked to high tensile strengths. CADMIUM PLATING
This protective coating offers excellent corrosion protection,
STAINLESS STEEL - AISI 316 ductility, natural lubricity and solderability in specialized
This type of stainless steel is heat resistant with superior applications.
corrosion resistance than other chromium nickel steels. It
offers high creep strength at elevated temperatures and PASSIVATION
resistance to pitting. The passivation process removes "free iron" contamination
left behind on the surface of stainless steel due to the
STAINLESS STEEL - PH17-7 manufacturing process. Also, the passivation process
A high strength corrosion-resistant steel with good facilitates the formation of a thin, transparent oxide film
workability, easy hardening and excellent mechanical that protects the stainless steel from selective oxidation
properties at elevated temperatures. Can be heat treated (corrosion).
at relatively low temperatures for high strength properties.
ZINC PHOSPHATE
BERYLLIUM COPPER This coating affords carbon steel excellent salt spray
Applications that require conductivity are best served by protection and corrosion resistance.
this material. It is also characterized by excellent corrosion
resistance and is particularly effective in sea air and seawater
atmospheres
10 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
Wave Springs
WAVE SPRING ADVANTAGE 17-7 STAINLESS STEEL
• Used for high stress and fatigue applications.
Using wave springs can reduce • Can withstand much higher temperatures than
traditional coil spring heights as much SAE 1070-1090 and not lose its spring qualities.
as 50% saving weight and costs as • Higher corrosion resistance than SAE 1070-1090.
well as reducing overall assembly
sizes. WAVE SPRING TERMS:
Coil Spring Wave Spring
STATIC: A spring that holds a load at a given height for the life
WAVE SPRING TYPES: of the assembly; there is no cycling of the part.
GAP SINGLE TURN/OVERLAP SINGLE TURN
Standard Inch (SST) / Narrow Inch (NST) / Metric (MST) DYNAMIC: A spring that is constantly moving up and down
until the end of its life. It has two working heights and hence,
• Ideal for short deflection applications with low to medium
two loads. Generally, the higher the cycle life the stronger the
forces. spring needs to be.
• Offered in a number of waves and material thicknesses.
• Designed for a wide range of bore and rod diameters. HYSTERESIS: The effect in springs where there is a higher
• Ideal for: response force during compression (loading) and a lower
- Narrow radial wall dimensions force during relaxation (unloading).
- Light duty applications
- Low clearance applications SPRING HEIGHTS: Free height—The height of the wave
- Ball or roller bearing applications spring when uncompressed; Work height—The height the
spring is compressed to for delivering the desired force.
MULTI-TURN PLAIN ENDS/MULTI-TURN SHIM ENDS
OPERATES IN BORE/CLEARS SHAFT: Pilot Bore - Designed
Light (WSL-MWL) / Medium (WSM-MWM) / Heavy (WSR-MWR) to fit in a bore, and have excess clearance by the shaft;
• Decreasing spring rate is proportional to the number of Pilot Shaft - Designed to fit over a shaft, and have excess
turns: More turns equals less force. clearance by the bore.
• Used for low force applications with large deflections.
• Utilizes nearly 1/2 the space as helical compression springs LOAD: The force the wave spring exerts when compressed.
while producing the same force. Load requirements can be stated three ways: A load
• Ideal for: requirement at a specific working height; the minimum load
- Medium & heavy duty applications requirement at one working height, and a maximum load
- High thrust load capacity requirement at another working height; the specified spring
rate between the minimum and maximum working heights.
- Light & medium bearing series: double row,
tapered bearing depending on the spring version. SPRING RATE: The force per displacement (lbs./in. or
Newton/mm.) More accurate than stamped wave washers.
CHOOSING A WAVE SPRING:
5 critical factors when considering a wave spring: DEFLECTION: How much the spring compresses.
• The constraints of the application: Pilot bore/shaft,
ID/OD, etc. DIAMETER EXPANSION: A wave spring tends to open
• The load (force). outward during compression, which will increase the diameter.
• The working height at which the load is applied.
• The material desired. FATIGUE: All springs suffer fatigue, the weakening or failure
• Whether it’s dynamic or static. of a material resulting from prolonged stress. This can be
compensated for with optimal materials and sizing.
MATERIAL TYPES:
SAE 1070-1090 CARBON STEEL To have Rotor Clip design engineers help you custom
• This prehardened material is the standard material for design a wave spring for your particular application, fill
wave springs.
out the Custom Wave Spring Design Form available at
• Less expensive option to Stainless Steel.
rotorclip.com/wave_spring_design_form or use our online
(Continued next column) custom wave spring calculator on rotorclip.com/wsc .
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 11
Hose Clamps Self-Compensating
For Low Pressure Applications,
Clamp It With Rotor Clamp
Rotor Clamp, Inc. produces a line of self-compensating hose clamps for low-pressure
applications in single wire, double wire and constant tension band (CTB) configurations,
including light band and narrow band clamps.
A hook catches a “dimple” when the clamp is opened for a more secure hold. The
clamp can then be glued in position on a hose.
The mechanism to hold the clamp open is accomplished with only minor changes to
the original design of the clamp. The clamp cannot be preopened any further than
the stop, ensuring the clamp will not be over-expanded. Contact technical sales for
more information: 1-800-557-6867.
12 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
Interchange Chart
Rotor Clip Products May Be Used Interchangeably
With The Part Numbers Indicated Below.
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 13
Axially Assembled, Internal
Once installed in the groove of a housing/bore, the portion of
HO Housing Rings the ring protruding from the groove (also called a “shoulder”)
holds an assembly in place.
Free Diameter & Ring Measurements Housing Diameter & Clearance Diameter Clearance Diameter & Gap
with Section B-B Groove Dimensions Compressed in Housing Width Released in Groove
14 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
Allowable Corner Radius and Chamfer Exploded Groove Profile & Edge Margin (Y) Alternate Lug Design Alternate Design
Maximum bottom radii (R), .005 for ring sizes For Larger Sizes (Manufacturer's Option)
-25 thru -100; .010 for ring sizes 102 thru 1000 (Manufacturer's Option)
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 15
Axially Assembled, Internal
Free Diameter & Ring Measurements Housing Diameter & Clearance Diameter Clearance Diameter & Gap
with Section B-B Groove Dimensions Compressed in Housing Width Released in Groove
16 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
Allowable Corner Radius and Chamfer Exploded Groove Profile & Edge Margin (Y) Alternate Lug Design Alternate Design
Maximum bottom radii (R), .005 for ring sizes For Larger Sizes (Manufacturer's Option)
-25 thru -100; .010 for ring sizes 102 thru 1000 (Manufacturer's Option)
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 17
Axially Assembled, Internal
Once installed in the groove of a housing/bore, the portion of
HO Housing Rings the ring protruding from the groove (also called a “shoulder”)
holds an assembly in place.
Free Diameter & Ring Measurements Housing Diameter & Clearance Diameter Clearance Diameter & Gap
with Section B-B Groove Dimensions Compressed in Housing Width Released in Groove
18 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
Allowable Corner Radius and Chamfer Exploded Groove Profile & Edge Margin (Y) Alternate Lug Design Alternate Design
Maximum bottom radii (R), .005 for ring sizes For Larger Sizes (Manufacturer's Option)
-25 thru -100; .010 for ring sizes 102 thru 1000 (Manufacturer's Option)
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 19
Axially Assembled, External
Once installed in the groove of a shaft, the portion of the ring
Free Diameter & Ring Measurements Shaft Diameter & Clearance Diameter Clearance Diameter &
with Section B-B Groove Dimensions Expanded Over Shaft Gaging Diameter
Released in Groove.
20 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 21
Axially Assembled, External
Once installed in the groove of a shaft, the portion of the ring
Free Diameter & Ring Measurements Shaft Diameter & Clearance Diameter Clearance Diameter &
with Section B-B Groove Dimensions Expanded Over Shaft Gaging Diameter
Released in Groove.
22 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 23
Axially Assembled, External
Once installed in the groove of a shaft, the portion of the ring
Free Diameter & Ring Measurements Shaft Diameter & Clearance Diameter Clearance Diameter &
with Section B-B Groove Dimensions Expanded Over Shaft Gaging Diameter
Released in Groove.
24 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 25
Axially Assembled, Internal Inverted
Functions like an HO ring in a housing/bore, only the lugs are
HOI Housing Rings “reversed.” This version reduces the distance the lugs of the standard
HO extend into the inner circumference of the housing/bore and allows
for another assembly to pass through unimpeded.
26 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 27
Axially Assembled, External Inverted
Functions like an SH ring on a shaft, only the lugs are “reversed.” This version
SHI Shaft Rings reduces the distance the lugs of the standard SH extend beyond the
circumference of the shaft. The shaft can then be used in an
application where clearance is minimal.
Free Diameter & Ring Measurements Shaft Diameter & Clearance Diameter Clearance Diameter & Gaging
with Section B-B Groove Dimensions Expanded Over Shaft Diameter Released in Groove
28 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
Exploded Groove Profile & Edge Margin (Y) Measuring Free Diameter Alternate Design
Maximum Corner Radius & Chamfer Maximum bottom radii (R), .005 for ring (Df) SHI Series Manufacturer’s Option
sizes -50 thru -100; .010 for ring sizes -106 Df = D1 - 2(S max)
thru -393
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 29
Axially Assembled, External Reinforced
The SHR is an extra thick version of a regular SH retaining ring.
30 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
Square Corner Abutment Maximum Corner Radius & Chamfer Exploded Groove Profile & Edge Alternate Design
Margin (Y)Maximum bottom radii (R), (Manufacturer’s
.005 for ring sizes -39 thru -98; -010 for Option)
ring sizes -106 thru -200
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 31
Axially Assembled, External Tamper-Proof
The SHM also functions like an SH retaining ring, but in “smaller”
SHM Shaft Rings applications. It is also a tamper proof ring which does not
have any lugs and can not be easily removed once installed.
Free Diameter & Ring Measurements Shaft Diameter & Clearance Diameter &
with Section B-B Groove Dimensions Gaging Diameter
32 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
Mandrel Bushing
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 33
Axially Assembled, Internal Bowed
Free Diameter & Ring Measurements Housing Diameter & Clearance Diameter Clearance Diameter &Gap
with Section B-B Groove Dimensions Compressed in Housing Width Released in Groove
34 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
Outer Groove Location Exploded Groove Profile & Edge Margin (Y)
Maximum Corner Radius & Chamfer A max = B min + J max Maximum bottom radii (R), .005 for ring sizes
A min = B max + J min -25 thru -100; .010 for ring sizes -102 and over
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 35
Axially Assembled, External Bowed
Compensating for accumulated tolerances is what a BSH “bowed”
Free Diameter & Ring Measurements Shaft Diameter & Groove Dimensions Clearance Diameter &
with Section B-B Gaging Diameter
36 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 37
Axially Assembled, Internal Beveled
These rings look exactly like their HO counterpart, only they have a
VHO Housing Rings 15° angle on the outer edge. This combines with a complementary
groove angle to eliminate endplay by wedging itself between the
groove and the retained part.
Free Diameter & Ring Measurements Housing Diameter & Clearance Diameter Clearance Diameter & Gap
with Section B-B Groove Dimensions Compressed in Housing Width Released in Groove
38 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 39
Axially Assembled, Internal Beveled
These rings look exactly like their HO counterpart, only they have a
VHO Housing Rings 15° angle on the outer edge. This combines with a complementary
groove angle to eliminate endplay by wedging itself between the
groove and the retained part.
Free Diameter & Ring Measurements Housing Diameter & Clearance Diameter Clearance Diameter & Gap
with Section B-B Groove Dimensions Compressed in Housing Width Released in Groove
40 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 41
Axially Assembled, Internal Beveled
These rings look exactly like their HO counterpart, only they have a
VHO Housing Rings 15° angle on the outer edge. This combines with a complementary
groove angle to eliminate endplay by wedging itself between the
groove and the retained part.
Free Diameter & Ring Measurements Housing Diameter & Clearance Diameter Clearance Diameter & Gap
with Section B-B Groove Dimensions Compressed in Housing Width Released in Groove
42 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 43
Axially Assembled, External Beveled
These rings look exactly like their SH counterpart, only they have a 15°
VSH Shaft Rings angle on the inner edge. This combines with a complimentary groove
angle to eliminate endplay by wedging itself between
the groove and the retained part.
Free Diameter & Ring Measurements Shaft Diameter & Clearance Diameter Clearance Diameter &
with Section B-B Groove Dimensions Expanded Over Shaft Gaging Diameter
Released in Groove
44 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
Exploded Groove Profile & Edge Margin Asymmetrical Design Alternate Lug Design
Maximum Corner Radius & Chamfer Maximum bottom radii (R), .005 for ring Manufacturer’s Manufacturer’s Option
sizes -100 thru -200; .010 for ring sizes Option For Larger Sizes
-206 thru -1000
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 45
Axially Assembled, External Beveled
These rings look exactly like their SH counterpart, only they have a 15°
VSH Shaft Rings angle on the inner edge. This combines with a complimentary groove
angle to eliminate endplay by wedging itself between
the groove and the retained part.
Free Diameter & Ring Measurements Shaft Diameter & Clearance Diameter Clearance Diameter &
with Section B-B Groove Dimensions Expanded Over Shaft Gaging Diameter
Released in Groove
46 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
Exploded Groove Profile & Edge Margin Asymmetrical Design Alternate Lug Design
Maximum Corner Radius & Chamfer Maximum bottom radii (R), .005 for ring Manufacturer’s Manufacturer’s Option
sizes -100 thru -200; .010 for ring sizes Option For Larger Sizes
-206 thru -1000
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 47
Radially Assembled, External ‘E’
Perhaps the most popular and widely used radial retaining ring is the “E” (so named
E Shaft Rings because it is shaped like the letter “E”.) Three prongs make contact with the bottom of
the groove and provide a shoulder for effective retention of assemblies.
Free Diameter & Ring Measurements Shaft Diameter & Clearance Diameter
With Section B-B Groove Dimensions Installed In Groove
48 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 49
Radially Assembled, External Reinforced ‘E’
The RE retaining ring is a reinforced version of the E ring, which will
RE Shaft Rings
accommodate higher thrust loadings and RPM. RE rings function in
the same groove as regular E rings, so that you can change
from one to the other without re-engineering the application.
Free Diameter & Ring Measurements Shaft Diameter & Clearance Diameter
with Section B-B Groove Dimensions Installed In Groove
50 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 51
Radially Assembled, External Crescent
Ideal for low clearance applications
Free Diameter & Ring Measurements Shaft Diameter & Clearance Diameter
with Section B-B Groove Dimensions Installed In Groove
52 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 53
Radially Assembled, External Interlocking
The LC ring is produced in two identical halves. The ends interlock into a groove on
LC Shaft Rings a shaft and, once assembled, are dynamically balanced. As a result, they are
particularly effective at retaining assemblies with extremely high rotational speeds.
Free Diameter & Ring Measurements Shaft Diameter & Plier Notch Design Clearance Diameter
with Section B-B Groove Dimensions (Call for additional information) Installed in Groove
54 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 55
Radially Assembled, External Poodle
The PO ring features wide “ears” (resembling those of a
PO/POL Shaft Rings poodle dog, thus the name) which offer extra retention
surface against the retained part. PO rings also come
in thinner sizes as a standard series of rings known as POL.
Free Diameter & Ring Measurements Shaft Diameter & Clearance Diameter
With Section B-B Groove Dimensions Installed In Groove
56 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
Optional
Exploded Groove Profile & Edge Center
Margin (Y)Maximum bottom radii (R), .005 Prong
For ring sizes 15 Design Optional Center
thru 50; .010 For ring sizes 62 thru 100 Prong Design
Maximum Corner Radius & Chamfer PO-125 thru 200
.015 For ring sizes 125 thru 150; .020
For ring sizes 175 thru 200
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 57
Radially Assembled, External Bowed ‘E’
Compensating for accumulated tolerances is what a BE “Bowed”
Free Diameter & Ring Measurements Shaft Diameter & Clearance Diameter
With Section B-B Groove Dimensions Installed In Groove
58 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 59
Radially Assembled, External Bowed Locking
Another variation of a bowed E ring is the EL. In addition to the
60 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
Exploded Groove Profile & Edge Margin (Y) Outer Grove Wall Location
Maximum bottom radii (R) .005 for ring sizes Lmax=Bmin + Jmax
-9 thru -25; .010 for ring sizes -31 thru -37 Lmin=Bmax + Jmin
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 61
External, Self-Locking Friction
The SHF ring resembles a regular SH ring except that it its designed to function on
SHF Shaft Rings a shaft without a groove. The design of the ring causes it to exert significant
gripping power uniformly on the shaft (except where the gap occurs.)
62 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
Maximum Corner Radius & Chamfer Maximum Corner Radius & Chamfer Exploded Groove Profile &
Optional Lug Design
(With Grooves) (Without Grooves) Edge Margin (Y)
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 63
External, Self-Locking Radial Grip
The RG makes indentations on either side of the groove once installed which
RG Shaft Rings significantly increases its holding power. It can also be installed directly
against the face of the retained part, virtually eliminating end play.
(Note: this product works only on “soft” shafts.)
Clearance Diameter
Free Diameter & Ring Measurements Installed On Shaft
64 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
External, Self-Locking Push-On (Curved Rim)
This ring features an outer rim with a series of prongs protruding into the center. The
ends create interference with the shaft when the ring is installed and a load introduced
to the other side. The outer rim of the TX is curved which affords greater thrust load
capacity and is easier to orient for assembly than the TY ring (next page.)
TX Shaft Rings
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 65
External, Self-Locking Push-On (Flat Rim)
This ring features an outer rim with a series of prongs
TY Shaft Rings protruding into the center. The ends create interference with the
shaft when the ring is installed and a load introduced to
the other side. The outer rim of the TY is flat.
66 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
Internal, Self-Locking Push-On
The internal version of the TY featuring a series of prongs protruding
outward. The ends create interference with the housing when the
ring is installed and a load introduced to the other side. TI Housing Rings
PLUNGER
For Fast, Easy Installation
Of Rotor Clip TX, TY Rings.
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 67
Axially Assembled, Internal, Metric
Once installed in the groove of a housing/bore, the portion of
Alternate Design
Groove Details (Manufacturer’s Option)
Free Diameter & Ring Measurements Groove Dimensions Allowable Corner Alternate Design Alternate Design
With Section B-B Radius & Chamfer (Manufacturer’s Option) (Manufacturer’s Option)
68 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
Alternate Design
Groove Details (Manufacturer’s Option)
Free Diameter & Ring Measurements Groove Dimensions Allowable Corner Alternate Design Alternate Design
With Section B-B Radius & Chamfer (Manufacturer’s Option) (Manufacturer’s Option)
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 69
Axially Assembled, Internal, Metric
Once installed in the groove of a housing/bore, the portion of
Alternate Design
Groove Details (Manufacturer’s Option)
Free Diameter & Ring Measurements Groove Dimensions Allowable Corner Alternate Design Alternate Design
With Section B-B Radius & Chamfer (Manufacturer’s Option) (Manufacturer’s Option)
70 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
Alternate Design
Groove Details (Manufacturer’s Option)
Free Diameter & Ring Measurements Groove Dimensions Allowable Corner Alternate Design Alternate Design
With Section B-B Radius & Chamfer (Manufacturer’s Option) (Manufacturer’s Option)
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 71
Axially Assembled, Internal, Metric
Once installed in the groove of a housing/bore, the portion of
Alternate Design
Groove Details (Manufacturer’s Option)
Free Diameter & Ring Measurements Groove Dimensions Allowable Corner Alternate Design Alternate Design
With Section B-B Radius & Chamfer (Manufacturer’s Option) (Manufacturer’s Option)
72 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
Alternate Design
Groove Details (Manufacturer’s Option)
Free Diameter & Ring Measurements Groove Dimensions Allowable Corner Alternate Design Alternate Design
With Section B-B Radius & Chamfer (Manufacturer’s Option) (Manufacturer’s Option)
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 73
Axially Assembled, Internal, Metric
Once installed in the groove of a housing/bore, the portion of
Alternate Design
Groove Details (Manufacturer’s Option)
Free Diameter & Ring Measurements Groove Dimensions Allowable Corner Alternate Design Alternate Design
With Section B-B Radius & Chamfer (Manufacturer’s Option) (Manufacturer’s Option)
74 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
Alternate Design
Groove Details (Manufacturer’s Option)
Free Diameter & Ring Measurements Groove Dimensions Allowable Corner Alternate Design Alternate Design
With Section B-B Radius & Chamfer (Manufacturer’s Option) (Manufacturer’s Option)
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 75
Axially Assembled, Internal Inverted, Metric
Functions like an DHO ring in a housing/bore, only the lugs are “reversed.”
DHI Housing Rings This version reduces the distance the lugs of the standard DHO extend into
the inner circumference of the housing/bore and allows
for another assembly to pass through unimpeded.
Alternate Design
(Manufacturer’s Option)
76 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
Alternate Design
(Manufacturer’s Option)
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 77
Axially Assembled, Internal Teeth, Metric
Similar in design to the DHO internal ring, this features several
78 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 79
Axially Assembled, Internal Reinforced, Metric
A thicker version of the DHO featuring a larger radial width than
80 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
Axially Assembled, External Reinforced, Metric
The DSR is an extra thick version of a regular DSH retaining ring.
As such, it is stronger and can withstand greater thrust loads
than its standard counterpart. DSR Shaft Rings
DIN 471 - Heavy Type
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 81
Axially Assembled, External, Metric
Once installed in the groove of a shaft, the portion
Alternate Design
Free Diameter & Ring Measurements Shaft Diameter & Maximum Corner Manufacturer’s Option
Groove Dimensions Radius & Chamfer Alternate Design sizes > -165
With Section B-B Manufacturer’s Option
82 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
Alternate Design
Free Diameter & Ring Measurements Shaft Diameter & Maximum Corner Manufacturer’s Option
Groove Dimensions Radius & Chamfer Alternate Design sizes > -165
With Section B-B Manufacturer’s Option
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 83
Axially Assembled, External, Metric
Once installed in the groove of a shaft, the portion
Alternate Design
Free Diameter & Ring Measurements Shaft Diameter & Maximum Corner Manufacturer’s Option
Groove Dimensions Radius & Chamfer Alternate Design sizes > -165
With Section B-B Manufacturer’s Option
84 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
Alternate Design
Free Diameter & Ring Measurements Shaft Diameter & Maximum Corner Manufacturer’s Option
Groove Dimensions Radius & Chamfer Alternate Design sizes > -165
With Section B-B Manufacturer’s Option
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 85
Axially Assembled, External, Metric
Once installed in the groove of a shaft, the portion
Alternate Design
Free Diameter & Ring Measurements Shaft Diameter & Maximum Corner Manufacturer’s Option
Groove Dimensions Radius & Chamfer Alternate Design sizes > -165
With Section B-B Manufacturer’s Option
86 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
Alternate Design
Free Diameter & Ring Measurements Shaft Diameter & Maximum Corner Manufacturer’s Option
Groove Dimensions Radius & Chamfer Alternate Design sizes > -165
With Section B-B Manufacturer’s Option
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 87
Axially Assembled, External, Metric
Once installed in the groove of a shaft, the portion
Alternate Design
Free Diameter & Ring Measurements Shaft Diameter & Maximum Corner Manufacturer’s Option
Groove Dimensions Radius & Chamfer Alternate Design sizes > -165
With Section B-B Manufacturer’s Option
88 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
Alternate Design
Free Diameter & Ring Measurements Shaft Diameter & Maximum Corner Manufacturer’s Option
Groove Dimensions Radius & Chamfer Alternate Design sizes > -165
With Section B-B Manufacturer’s Option
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 89
Axially Assembled, External Inverted, Metric
Functions like a DSH ring in a shaft, only the lugs are “reversed.”
DSI Shaft Rings This version reduces the distance the lugs of the standard DSH
extend beyond the circumference of the shaft. The shaft can then
be used in an application where clearance is minimal.
Alternate Design
(Manufacturer’s Option)
The radius “R”
on the load side
must not
exceed 0.1T
Free Diameter & Ring Shaft Diameter &
Measurements Groove Dimensions
Maximum corner
With Section B-B Measuring Free Diameter (Df)
Radius & Chamfer
DSI SERIES Df=D1-2S
90 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
Alternate Design
(Manufacturer’s Option)
The radius “R”
on the load side
must not
exceed 0.1T
Free Diameter & Ring Shaft Diameter &
Measurements Groove Dimensions
Maximum corner
With Section B-B Measuring Free Diameter (Df)
Radius & Chamfer
DSI SERIES Df=D1-2S
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 91
Axially Assembled, External Teeth, Metric
Similar in design to the DSH external ring, this features several “teeth”
Free Diameter & Ring Measurements Shaft Diameter & Maximum Corner
With Section B-B Groove Dimensions Radius & Chamfer
92 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
Free Diameter & Ring Measurements Shaft Diameter & Maximum Corner
With Section B-B Groove Dimensions Radius & Chamfer
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 93
Radially Assembled, External E, Metric
Perhaps the most popular and widely used radial retaining ring
DE Shaft Rings
(DIN 6799)
is the “E” (so named because it is shaped like the letter “E”).
Three prongs make contact with the bottom of the groove
and provide a shoulder for effective retention of assemblies.
Clearance Diameter
Installed In Groove
Edge Margin (Y)
Shaft Diameter & Maximum Corner The radius “R” on the load
Ring Measurements Groove Dimensions Radius & Chamfer side must not exceed 0.1T.
94 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
External, Self-Locking Friction, Metric
The DSF ring resembles a regular DSH ring except that it its designed to
function on a shaft without a groove. The design of the ring causes it to exert
significant gripping power uniformly on the shaft (except where the gap occurs.) DSF Shaft Rings
Clearance Diameter
Free Diameter & Ring Measurements Shaft Diameter Installed on Shaft
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 95
Radially Assembled, External Crescent, Metric
Ideal for low clearance applications where radial
96 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 97
Self-Locking, External “Push-On”, Metric
This ring features a curved outer rim with a series of prongs
DTX Shaft Rings protruding into the center. The ends create interference with the
shaft when the ring is installed and a load introduced to the other side.
98 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
Self-Locking, Internal “Push-On”, Metric
The internal version of the TX with a curved inner rim and
a series of prongs protruding outward. The ends create
interference with the housing when the ring is installed and
a load introduced to the other side.
DTI Housing Rings
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 99
Axially Assembled, Internal, ANSI Metric
Once installed in the groove of a housing/bore, the portion
MHO Housing Rings of the ring protruding from the groove (also called a
“shoulder”) holds an assembly in place.
Free Diameter & Ring Measurements Housing Diameter & Clearance Diameter Clearance Diameter & Gap
With Section B-B Groove Dimensions Compressed In Housing Width Released In Groove
100 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
Exploded Groove Profile & Edge Margin (Y) Alternate Lug Design Alternate Design
Allowable Corner Radius & Chamfer Maximum bottom radii (R), 0.10 for ring sizes For Larger Sizes (Manufacturer’s Option)
-8 thru -17; 0.2 for ring sizes -18 thru -30; (Manufacturer’s Option)
0.3 for ring sizes -32 thru -55
0.4 for ring sizes -56 thru -250
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 101
Axially Assembled, Internal, ANSI Metric
Once installed in the groove of a housing/bore, the portion
MHO Housing Rings of the ring protruding from the groove (also called a
“shoulder”) holds an assembly in place.
Free Diameter & Ring Measurements Housing Diameter & Clearance Diameter Clearance Diameter & Gap
With Section B-B Groove Dimensions Compressed In Housing Width Released In Groove
102 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
Exploded Groove Profile & Edge Margin (Y) Alternate Lug Design Alternate Design
Allowable Corner Radius & Chamfer Maximum bottom radii (R), 0.10 for ring sizes For Larger Sizes (Manufacturer’s Option)
-8 thru -17; 0.2 for ring sizes -18 thru -30; (Manufacturer’s Option)
0.3 for ring sizes -32 thru -55
0.4 for ring sizes -56 thru -250
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 103
Axially Assembled, Internal, ANSI Metric
Once installed in the groove of a housing/bore, the portion
MHO Housing Rings of the ring protruding from the groove (also called a
“shoulder”) holds an assembly in place.
Free Diameter & Ring Measurements Housing Diameter & Clearance Diameter Clearance Diameter & Gap
With Section B-B Groove Dimensions Compressed In Housing Width Released In Groove
104 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
Exploded Groove Profile & Edge Margin (Y) Alternate Lug Design Alternate Design
Allowable Corner Radius & Chamfer Maximum bottom radii (R), 0.10 for ring sizes For Larger Sizes (Manufacturer’s Option)
-8 thru -17; 0.2 for ring sizes -18 thru -30; (Manufacturer’s Option)
0.3 for ring sizes -32 thru -55
0.4 for ring sizes -56 thru -250
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 105
Axially Assembled, External, ANSI Metric
Once installed in the groove of a shaft, the portion of the
MSH Shaft Rings ring protruding from the groove (also called
a “shoulder”) holds an assembly in place.
Free Diameter & Ring Measurements Shaft Diameter & Clearance Diameter Clearance Diameter &
with Section B-B Groove Dimensions Expanded Over Shaft Gaging Diameter
Released in Groove.
106 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 107
Axially Assembled, External, ANSI Metric
Once installed in the groove of a shaft, the portion of the
MSH Shaft Rings ring protruding from the groove (also called
a “shoulder”) holds an assembly in place.
Free Diameter & Ring Measurements Shaft Diameter & Clearance Diameter Clearance Diameter &
with Section B-B Groove Dimensions Expanded Over Shaft Gaging Diameter
Released in Groove.
108 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 109
Axially Assembled, External Reinforced, ANSI Metric
The MSR is an extra thick version of a regular MSH
MSR Shaft Rings retaining ring. As such, it is stronger and can withstand
greater thrust loads than its standard counterpart.
110 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 111
Radially Assembled, External ‘E’, ANSI Metric
Perhaps the most popular and widely used radial retaining
ME Shaft Rings ring is the “E” (so named because it is shaped like the letter “E”).
Three prongs make contact with the bottom of the groove
and provide a shoulder for effective retention of assemblies.
Free Diameter & Ring Measurements Shaft Diameter & Clearance Diameter &
With Section B-B Groove Dimensions Installed In Groove
112 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 113
Radially Assembled, External Crescent, ANSI Metric
Ideal for low clearance applications
Free Diameter & Ring Measurements Shaft Diameter & Clearance Diameter
With Section B-B Groove Dimensions Installed In Groove
114 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 115
Radially Assembled, External Reinforced ‘E’, ANSI Metric
The MRE retaining ring is a reinforced version of the ME ring, which will
MRE Shaft Rings accommodate higher thrust loadings and RPM. MRE rings function in the
same size grooves as regular E rings, so that you can change from one to
the other without re-engineering the application.
Free Diameter & Ring Measurements Shaft Diameter & Clearance Diameter
With Section B-B Groove Dimensions Installed in Groove
116 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 117
Radially Assembled, External ‘E’, JIS
Perhaps the most popular and widely used radial retaining
JE Shaft Rings
(JIS B 2805)
ring is the “E” (so named because it is shaped like the letter “E”).
Three prongs make contact with the bottom of the groove
and provide a shoulder for effective retention of assemblies.
Free Diameter & Ring Measurements Shaft Diameter & Groove Dimensions
With Section B-B
118 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
Snap Ring, Internal, Inch
Designed for needle bearings, once installed in
the groove of a housing/bore, the portion of the
ring protruding from the groove holds an
assembly in place.
HN Constant Section Rings
For alternate cutoff styles, contact Rotor Clip Technical Sales at 1-800-557-6867 (E-mail: tech@rotorclip.com)
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 119
Snap Ring, Internal Notched, Inch
Once installed in the groove of a housing/bore,
UHO Constant Section Rings the portion of the ring protruding from the
groove holds an assembly in place.
For alternate cutoff styles, contact Rotor Clip Technical Sales at 1-800-557-6867 (E-mail: tech@rotorclip.com)
120 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For alternate cutoff styles, contact Rotor Clip Technical Sales at 1-800-557-6867 (E-mail: tech@rotorclip.com)
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 121
Snap Ring, Internal, Inch
Once installed in the groove of a housing/bore,
UHB Constant Section the portion of the ring protruding from the
groove holds an assembly in place.
For alternate cutoff styles, contact Rotor Clip Technical Sales at 1-800-557-6867 (E-mail: tech@rotorclip.com)
122 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For alternate cutoff styles, contact Rotor Clip Technical Sales at 1-800-557-6867 (E-mail: tech@rotorclip.com)
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 123
Snap Ring, Internal, Inch
Once installed in the groove of a housing/bore,
UHB Constant Section the portion of the ring protruding from the
groove holds an assembly in place.
For alternate cutoff styles, contact Rotor Clip Technical Sales at 1-800-557-6867 (E-mail: tech@rotorclip.com)
124 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
Snap Ring, External, Inch
Once installed in the groove of a shaft,
the portion of the ring protruding from the
groove holds an assembly in place. USC Constant Section
For alternate cutoff styles, contact Rotor Clip Technical Sales at 1-800-557-6867 (E-mail: tech@rotorclip.com)
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 125
Snap Ring, External, Inch
Once installed in the groove of a shaft,
For alternate cutoff styles, contact Rotor Clip Technical Sales at 1-800-557-6867 (E-mail: tech@rotorclip.com)
126 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 127
Snap Ring, External Notched, Inch
Once installed in the groove of a shaft
USH Constant Section the portion of the ring protruding from the
groove holds an assembly in place.
For alternate cutoff styles, contact Rotor Clip Technical Sales at 1-800-557-6867 (E-mail: tech@rotorclip.com)
128 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
Snap Ring, External, Inch
A light-duty ring designed for needle bearings,
once installed in the groove of a shaft
the portion of the ring protruding from the
groove holds an assembly in place.
SNL Constant Section
For alternate cutoff styles, contact Rotor Clip Technical Sales at 1-800-557-6867 (E-mail: tech@rotorclip.com)
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 129
Snap Ring, External, Inch
SLC/SLO Square Section.
Once installed in the groove of a shaft
130 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
Snap Ring, External, Inch
Round Section.
Once installed in the groove of a shaft
RLC/RLO
the portion of the ring protruding from the
groove holds an assembly in place. RHC/RHO Constant Section
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 131
Snap Ring, Internal, Metric
Designed for SAE Standard Metric Bearings.
For alternate cutoff styles, contact Rotor Clip Technical Sales at 1-800-557-6867 (E-mail: tech@rotorclip.com)
132 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For alternate cutoff styles, contact Rotor Clip Technical Sales at 1-800-557-6867 (E-mail: tech@rotorclip.com)
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 133
Snap Ring, External, Metric
For Grooves in Outer Tracks of Ball or Roller Bearings.
For alternate cutoff styles, contact Rotor Clip Technical Sales at 1-800-557-6867 (E-mail: tech@rotorclip.com)
134 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
Snap Ring, External, Metric
For SAE Standard Metric Bearings.
Once installed in the groove of a shaft,
the portion of the ring protruding from the
groove holds an assembly in place.
SB Constant Section
Drawing depicts using rings to retain bearings Shaft Diameter & Free Diameter &
in a typical shaft application. Groove Dimensions Ring Measurements
For alternate cutoff styles, contact Rotor Clip Technical Sales at 1-800-557-6867 (E-mail: tech@rotorclip.com)
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 135
Snap Ring, External, Metric
Flat Wire.
Free Diameter & Ring Dimensions Shaft Diameter & Groove Dimensions
136 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
Free Diameter & Ring Dimensions Shaft Diameter & Groove Dimensions
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 137
Snap Ring, External, Metric
Flat Wire.
Free Diameter & Ring Dimensions Shaft Diameter & Groove Dimensions
138 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
Snap Ring, External, Metric
For Bearings.
Once installed in the groove of a shaft,
the portion of the ring protruding from the
groove holds an assembly in place.
CBS Constant Section DIN 5417
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 143
Snap Ring, External, Metric
For Bearings.
144 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
Snap Ring, External, Metric
Round Wire.
Once installed in the groove of a shaft,
the portion of the ring protruding from the
groove holds an assembly in place.
CRS Constant Section DIN 7993
Free Diameter & Ring Dimensions Shaft Diameter & Groove Dimensions
For alternate cutoff styles, contact Rotor Clip Technical Sales at 1-800-557-6867 (E-mail: tech@rotorclip.com)
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 145
Snap Ring, Internal, Metric
Round Wire.
Once installed in the groove of a housing/bore,
the portion of the ring protruding from the
groove holds an assembly in place.
CRH Constant Section DIN 7993
Free Diameter & Ring Dimensions Housing Diameter & Groove Dimensions
For alternate cutoff styles, contact Rotor Clip Technical Sales at 1-800-557-6867 (E-mail: tech@rotorclip.com)
146 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
Constant Section Ring Optional Cutoff Styles
The following cutoff styles represent "specials" requested by the marketplace over a period of many years.One of
these configurations may suit your application requirements and may be substituted for any size ring listed in the
catalog specification pages. Or, we can make any configuration your application requires. For more information,
contact Rotor Clip technical sales: 1-800-557-6867, E-mail: tech@rotorclip.com.
Internal/Notched External/Notched External/
Speared Ends
A B C
D E F
G H J
K L M
N P
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 147
Internal, Light Duty
These single-turn retaining rings are ideal for
Free Diameter & Ring Measurements Housing Diameter & Groove Dimensions
148 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
Free Diameter & Ring Measurements Housing Diameter & Groove Dimensions
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 149
External, Light Duty
These single-turn retaining rings are ideal for
Free Diameter & Ring Measurements Shaft Diameter & Groove Dimensions
150 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
Free Diameter & Ring Measurements Shaft Diameter & Groove Dimensions
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 151
Internal, Medium Duty
These rings offer the greatest economy in price and size.
KM Spiral Housing Rings They are able to handle approximately twice the
thrust capacity of the KL series, and to be
produced to military specifications if needed.
KM-50 to KM-150
152 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
KM-50 to KM-150
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 153
Internal, Medium Duty
These rings offer the greatest economy in price and size.
KM Spiral Housing Rings They are able to handle approximately twice the
thrust capacity of the KL series, and to be
produced to military specifications if needed.
KM-50 to KM-150
154 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
KM-50 to KM-150
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 155
External, Medium Duty
These rings offer the greatest economy in price and size.
CM Spiral Shaft Rings They are able to handle approximately twice the
thrust capacity of the CL series, and to be
produced to military specifications if needed.
CM-50 to CM-150
156 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
CM-50 to CM-150
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 157
External, Medium Duty
These rings offer the greatest economy in price and size.
CM Spiral Shaft Rings They are able to handle approximately twice the
thrust capacity of the CL series, and to be
produced to military specifications if needed.
CM-50 to CM-150
158 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
CM-50 to CM-150
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 159
Internal, Medium-Heavy Duty
With load bearing capacities closer to the Heavy-duty
KR-156 to KR-600
KR-50 to KR-150
160 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
KR-156 to KR-600
KR-50 to KR-150
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 161
External, Medium-Heavy Duty
Externally fitted to up to 10in. Shaft diameter, these rings can
CR Spiral Shaft Rings handle all but the most rigorous applications.
CR-156 to CR-600
CR-46 to CR-150
162 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
CR-156 to CR-600
CR-46 to CR-150
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 163
Internal, Heavy Duty
The greatest size range and thrust capacity make these
KG Spiral Housing Rings rings the only choice for applications that require minimum
deflection or thrust loads that demand a deep groove capacity.
KG-50 to KG-75
164 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
KG-50 to KG-75
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 165
Internal, Heavy Duty
The greatest size range and thrust capacity make these
KG Spiral Housing Rings rings the only choice for applications that require minimum
deflection or thrust loads that demand a deep groove capacity.
KG-50 to KG-75
166 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
KG-50 to KG-75
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 167
External, Heavy Duty
The rigors of the toughest applications are easily
CG Spiral Shaft Rings handled by this external series. Its large size, and
ease of application and removal, transfers into
an assurance of quality for demanding uses.
CG-46 to CG-66
168 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
CG-46 to CG-66
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 169
External, Heavy Duty
The rigors of the toughest applications are easily
CG Spiral Shaft Rings handled by this external series. Its large size, and
ease of application and removal, transfers into
an assurance of quality for demanding uses.
CG-46 to CG-66
170 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
CG-46 to CG-66
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 171
Internal, Heavy-Duty Snap Ring
These single-turn snap rings are ideal
KLR Spiral Housing Rings for applications involving high thrust loads.
Optional End
Designs
Free Diameter & Ring Measurements Housing Diameter & Groove Dimensions
172 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
Optional End
Designs
Free Diameter & Ring Measurements Housing Diameter & Groove Dimensions
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 173
External, Heavy-Duty Snap Ring
These single-turn snap rings are ideal
CLR Spiral Shaft Rings for applications involving high thrust loads.
174 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 175
Internal, Heavy Duty DIN
An internal metric ring which meets DIN
Free Diameter & Ring Measurements Housing Diameter & Groove Dimensions
176 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
Free Diameter & Ring Measurements Housing Diameter & Groove Dimensions
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 177
Internal, Heavy Duty DIN
An internal metric ring which meets DIN
Free Diameter & Ring Measurements Housing Diameter & Groove Dimensions
178 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
Free Diameter & Ring Measurements Housing Diameter & Groove Dimensions
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 179
External, Heavy Duty DIN
For applications where European DIN standards need
Free Diameter & Ring Measurements Shaft Diameter & Groove Dimensions
180 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
Free Diameter & Ring Measurements Shaft Diameter & Groove Dimensions
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 181
Internal, Light Duty, Metric
These single-turn retaining rings are ideal for
Optional End
Designs
Free Diameter & Ring Measurements Housing Diameter & Groove Dimensions
182 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
Optional End
Designs
Free Diameter & Ring Measurements Housing Diameter & Groove Dimensions
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 183
External, Light Duty, Metric
These single-turn retaining rings are ideal for
184 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 185
Internal, Light-Duty, Metric
These single-turn retaining rings are ideal for
Free Diameter & Ring Measurements Housing Diameter & Groove Dimensions
186 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
Free Diameter & Ring Measurements Housing Diameter & Groove Dimensions
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 187
External, Light-Duty, Metric
These single-turn retaining rings are ideal for
Free Diameter & Ring Measurements Shaft Diameter & Groove Dimensions
188 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
Free Diameter & Ring Measurements Shaft Diameter & Groove Dimensions
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 189
Internal, Medium Duty, Metric
These rings offer the greatest economy in price and size.
MKM Spiral Housing Rings They are able to handle approximately twice the
thrust capacity of the DKL series.
MKM-12 to MKM-36
190 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
MKM-12 to MKM-36
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 191
External, Medium Duty, Metric
These rings offer the greatest economy in price and size.
MCM Spiral Shaft Rings They are able to handle approximately twice the
thrust capacity of the DCL series.
MCM-12 to MCM-40
192 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
MCM-12 to MCM-40
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 193
Internal, Medium-Heavy Duty Metric
With load bearing capacities closer to the Heavy-duty
MKR Spiral Housing Rings series, and almost universal groove dimensions,
these rings offer greatest ease of assembly
with greatest thrust capacity.
MKR-36 to MKR-155
MKR-12 to MKR-35
194 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
MKR-36 to MKR-155
MKR-12 to MKR-35
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 195
External, Medium-Heavy Duty, Metric
With load bearing capacities closer to the Heavy-duty
MCR Spiral Shaft Rings series, and almost universal groove dimensions,
these rings offer greatest ease of assembly
with greatest thrust capacity
MCR-36 to MCR-155
MCR-12 to MCR-35
196 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
MCR-36 to MCR-155
MCR-12 to MCR-35
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 197
Internal, Heavy Duty, Metric
The greatest size range and thrust capacity make
MKG Spiral Housing Rings these rings the only choice for applications
that require minimum deflection or thrust
loads that demand a deep groove capacity.
MKG-12 to MKG-19
198 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
MKG-12 to MKG-19
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 199
External, Heavy Duty, Metric
The rigors of the toughest applications are easily
MCG Spiral Shaft Rings handled by this external series. Its large size, and
ease of application and removal, transfers into
an assurance of quality for demanding uses.
MCG-12 to MCG-17
200 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
MCG-12 to MCG-17
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 201
Internal, Aerospace, Metric
Dimensions Conform to Metric Aerospace
MKA-12 to MKA-19
202 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
MKA-12 to MKA-19
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 203
External, Aerospace, Metric
Dimensions Conform to Metric Aerospace
MCA-12 to MCA-17
204 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
MCA-12 to MCA-17
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 205
Internal, Spiral, Inch
The waves in this spiral ring
NKG TruWave TM
Housing Ring
compensate for accumulated
tolerances.
Free Diameter & Ring Measurements Shaft Diameter & Groove Dimensions
206 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
External, Spiral, Inch
The waves in this spiral ring
compensate for accumulated
tolerances. NCG TruWave TM
Shaft Ring
Free Diameter & Ring Measurements Shaft Diameter & Groove Dimensions
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 207
Single Turn, Inch
Ideal for short deflection applications with low to medium
208 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 209
Single Turn, Narrow, Inch
Ideal for short deflection applications where
Gap Type
*Multiple Waves
(see table)
210 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
Single Turn, Metric
Ideal for short deflection applications with low to medium
forces. Offered in a number of waves and material
thicknesses. Designed for a wide range of bore
and rod diameters.
MST Wave Springs
Wave Spring Measurements
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 211
Single Turn, Metric
Ideal for short deflection applications with low to medium
212 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
Bearing Interchange Chart
This chart pairs metric single turn wave springs with
the appropriate standard bearing number.
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 213
Multi Turn, Inch
WSL,WSM, Used for low force applications with large deflections:
More turns equals less force. Utilizes nearly half the space as
WSR Wave Springs helical compression springs while producing the same force.
214 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 215
Multi Turn, Inch
WSL,WSM, Used for low force applications with large deflections:
More turns equals less force. Utilizes nearly half the space as
WSR Wave Springs helical compression springs while producing the same force.
216 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 217
Multi Turn, Inch
WSL,WSM, Used for low force applications with large deflections:
More turns equals less force. Utilizes nearly half the space as
WSR Wave Springs helical compression springs while producing the same force.
218 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 219
Multi Turn, Inch
WSL,WSM, Used for low force applications with large deflections:
More turns equals less force. Utilizes nearly half the space as
WSR Wave Springs helical compression springs while producing the same force.
220 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 221
Multi Turn, Inch
WSL,WSM, Used for low force applications with large deflections:
More turns equals less force. Utilizes nearly half the space as
WSR Wave Springs helical compression springs while producing the same force.
222 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
Multi Turn, Metric
Used for low force applications with large deflections:
More turns equals less force. Utilizes nearly half the space as
MWL,MWM,
helical compression springs while producing the same force.
MWR Wave Springs
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 223
Multi Turn, Metric
MWL,MWM, Used for low force applications with large deflections:
More turns equals less force. Utilizes nearly half the space as
MWR Wave Springs helical compression springs while producing the same force.
224 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 225
Multi Turn, Metric
MWL,MWM, Used for low force applications with large deflections:
More turns equals less force. Utilizes nearly half the space as
MWR Wave Springs helical compression springs while producing the same force.
226 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 227
Multi Turn, Metric
MWL,MWM, Used for low force applications with large deflections:
More turns equals less force. Utilizes nearly half the space as
MWR Wave Springs helical compression springs while producing the same force.
228 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 229
Multi Turn, Metric
MWL,MWM, Used for low force applications with large deflections:
More turns equals less force. Utilizes nearly half the space as
MWR Wave Springs helical compression springs while producing the same force.
230 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 231
Multi Turn, Metric
MWL,MWM, Used for low force applications with large deflections:
More turns equals less force. Utilizes nearly half the space as
MWR Wave Springs helical compression springs while producing the same force.
232 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
www.rotorclip.com
1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 233
Multi Turn, Metric
MWL,MWM, Used for low force applications with large deflections:
More turns equals less force. Utilizes nearly half the space as
MWR Wave Springs helical compression springs while producing the same force.
234 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
Shims
Shims are typically used in order to support, adjust for
better fit, or provide a level surface. Shims may also be
used as spacers to fill gaps between parts subject to wear. KMS Shims
Shim Measurements
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 235
Single Wire, Self-Compensating Hose Clamp
Single wire clamps have the most effective holding force and
HC Hose Clamps clamping strength. The single wire concentrates the clamping
force in one specific area around the hose.
EFFECTIVE CLAMPING RANGE: After expanding to no greater than “A” diameter of the gage, the clamp in relaxed condition shall not pass over “D”
diameter. When clamp is assembled on “A”, “B” or “C” diameter of gage, a wire of “X” diameter shall not pass between gage and clamp when inserted
in a direction parallel to the axis of the gage.
FINISH: Peen-Plate Zinc (non-electrolytic process) .0002 minimum thickness plus dichromate treatment. (See color codes below.)
MATERIAL: Specially processed premium grade spring wire, hardened and austempered to meet the performance requirements specified.
236 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
Slim Wire, Self-Compensating Hose Clamp
A slimmer version of the Single Wire Hose clamp. The single wire
concentrates the clamping force in one specific area around the
hose. Can be installed with manual and pneumatic tools HW Hose Clamps
EFFECTIVE CLAMPING RANGE: After expanding to no greater than “A” diameter of the gage, the clamp in relaxed condition shall not pass over “D”
diameter. When clamp is assembled on “A”, “B” or “C” diameter of gage, a wire of “X” diameter shall not pass between gage and clamp when inserted
in a direction parallel to the axis of the gage.
FINISH: Peen-Plate Zinc (non-electrolytic process) .0002 minimum thickness plus dichromate treatment. (See color codes below.)
MATERIAL: Specially processed premium grade spring wire, hardened and austempered to meet the performance requirements specified.
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 237
Double Wire, Self-Compensating Hose Clamp
Double wire clamps are used where a lower clamping force than offered by
DW Hose Clamps single wire clamps is sufficient and aesthetics are important. The double
wound wire spreads out the clamping force around the hose, and are more
cost effective than single wire clamps.
EFFECTIVE CLAMPING RANGE: After expanding to no greater than “A” diameter of the gage, the clamp in relaxed condition shall not pass over “D”
diameter. When clamp is assembled on “A”, “B” or “C” diameter of gage, a wire of “X” diameter shall not pass between gage and clamp when inserted
in a direction parallel to the axis of the gage.
FINISH: Peen-Plate Zinc (non-electrolytic process) .0002 minimum thickness plus dichromate treatment. (See color codes below.)
MATERIAL: Specially processed premium grade spring wire, hardened and austempered to meet the performance requirements specified.
238 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
Constant Tension Band, Self-Compensating Hose Clamp
Constant Tension Band clamps are used in applications where a lower
clamping force than offered by single wire clamps is sufficient, but a
higher clamping force than produced by double wire clamps is needed. CTB Hose Clamps
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 239
Constant Tension Light Band,
Self-Compensating Hose Clamp
CTL Hose Clamps These are cost effective alternatives to other types
of band clamps, but do not compromise quality or reliability.
240 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
Pre-Positioned, Pre-Opened, Self-Compensating Hose Clamp
This band clamp is held in the open position by compressing the tangs
and allowing the stop to hook on to a complementary notch on the
side on one of the tangs. Must be pre-glued to the hose.
.
CTO Hose Clamps
Pre-Opened, Pre-Positioned Clamps
This unique, patented version of a preopened clamp is held in the open
position by compressing the tangs and allowing the stop to hook on to a
complementary notch on the side on one of the tangs.
This clamp is intended solely for rubber hose manufacturers who pre-glue
clamps to hoses before supplying to the automotive industry.
A hook catches a “dimple” when the clamp is opened for a more secure hold. The
clamp can then be glued in position on a hose.
The mechanism to hold the clamp open is accomplished with only minor changes to the original design of the clamp. The
clamp cannot be preopened any further than the stop, ensuring the clamp will not be over-expanded. Contact technical
sales for more information:
1-800-557-6867, or e-mail tech@rotorclip.com.
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 241
Standard Pliers
Standard Retaining Ring Pliers - Inch & Metric
Rotor Clip Standard Retaining Ring Pliers are made of high carbon, heat treated steel and produced to exacting
QC specifications. They feature stop and return springs for problem-free installation/removal of retaining rings. This
eliminates overspreading of external retaining rings, and speeds the assembly/removal of internal retaining rings by
orienting plier to exact location of lug holes. Most Rotor Clip retaining ring pliers have exclusive air-cushioned
handles.
Internal Inch
For use with the following
inch retaining rings:
HO HOI
BHO VHO
External Inch
For use with the following
inch retaining rings:
SH SHI
SHR SHF
BSH VSH
External pliers RP-12, RP-15 & RP-18 are available in the standard version with shielded tips. The 45° and 90° versions are unshielded.
Both are equipped with fixed stops to prevent overspreading of the external retaining rings during installation or removal.
Internal Metric
For use with the following
metric retaining rings:
DHO DHT
External Metric
For use with the following
metric retaining rings:
DSH DST
242
Ratchet & Grip Ring Pliers
Ratchet Retaining Ring Pliers
Assemble large retaining rings up to 10” in diameter with ease and comfort using Rotor Clip Ratchet Pliers.
Spring loaded mechanisms compress or expand large rings through gradual “steps.” Plier locks at the desired
size without continued pressure on the handles.
(Note: Ratchet Pliers do not include plier tips, which must be purchased separately.)
Internal
For use with the
following retaining rings:
HO HOI
BHO VHO
External
For use with the
following retaining rings:
SH SHI
SHR BSH
VSH
External
For use with the
following retaining rings:
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 243
Convertible & Heavy-Duty Pliers
Convertible Retaining Ring Pliers
Convert quickly and easily from internal to external pliers and back again.This two-in-one capability is cost
effective and ideal for handling a variety of applications with a minimum number of tools. Simply move the
screw to the other hole and tighten with finger pressure to convert quickly to an internal/external plier.
Internal
For use with the
following retaining rings:
HO HOI
BHO VHO
External
For use with the
following retaining rings:
SH SHI
SHR BSH
SHF VSH
Internal
For use with the
following retaining rings:
HO HOI
DHO DHT
MHO
External
For use with the
following retaining rings:
SH SHI
SHR DSH
DST MSH
244 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
Dispensers
D
Retaining Ring Dispensers Rotor Clip retaining ring dispensers feature “rail” over which a
stack of retaining rings can be slipped. Once in position, they can be “dispensed” one at a time using a retaining
ring applicator for ease of installation. Two such models are available to meet you particular dispensing needs:
Spring Rail (SD) dispensers are competitively priced and offer significant improvements (like more rail capacity and
SD durable construction) on existing designs. For use with Rotor Clip C, E/SE/YE, RE, PO/POL, DE, DC, ME & JE rings.
SD The Heavy Duty (D) is a more permanent version which features replaceable parts and can be permanently affixed
to your work station.
Features:
•Sturdy, Industrial-Quality Construction. •Longer Rail For More Capacity.
•Fast, Easy Loading. •Part and Tool Number Stamped on Dispenser for Fast, Easy
•Accept Tape-Stacked Rings. Identification of Tool and Corresponding Ring.
•Precise, Single Ring Ejection. •Powder Metal Coating for a Durable, No-Rust Finish (Spring
Rail Dispenser, Only.)
RE Dispensers
For use with Rotor Clip “RE” Rings.
JE Dispensers
For use with Rotor Clip “JE” Rings.
ME Dispensers
For use with Rotor Clip “ME” Rings.
DC Dispensers DE Dispensers
For use with Rotor Clip “DC” Rings.
For use with Rotor Clip “DE” Rings.
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 245
Applicators
Retaining Ring Applicators
Applicators are designed to install standard inch & metric radial retaining rings on a shaft. Used with Rotor Clip
Dispensers, applicators enable operators to install rings quickly and correctly and allows for installation without
turning the tool (ring “snaps” when properly seated in groove.) Heat treated for strength. For use with Rotor Clip
C, E, BE, RE, PO/POL, EL, DE, DC, ME and JE Retaining rings.
PO Applicator
POL For use with Rotor Clip “PO/POL” Rings.**
JE Applicator
For use with Rotor Clip “JE” Rings.**
246 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
Applicators
DE Applicator ME Applicator For Bowed “E” Rings
For use with Rotor Clip “DE” Rings.** For use with Rotor Clip “ME” Rings.**
BE Applicator
BSE For use with Rotor Clip “BE/BSE” Rings.
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 247
Automatic Assembly Tools
Pneumatic Retaining Ring Tools
These pneumatic hand tools automate assembly using a compressed air line (85 psi). Saves time while
eliminating injury. Pneumatic Retaining Ring Tools are designed to fit the following inch/metric retaining rings:
HO, VHO, BHO, HOI, SH, VSH, BSH, SHI, SHR, DHO, DSH, DST, DHT.
Call 1-800-557-6867 for technical information, or e-mail tech@rotorclip.com.
* Note: Power pack and tips must be purchased together for tool to operate.
External For use with the following retaining rings: Internal For use with the following retaining rings:
SH VSH BSH SHI SHR DSH DST HO VHO BHO HOI DHO DHT
HAZ-2 Pliers Single Wire Hose Clamp Plier - Heavy Duty (HAZ-2)
For use with single
wire “HC” hose clamps: A heavy-duty version of the Single Wire Pliers (KC-18). Tool locks into place when clamp is
fully compressed, relieving hand pressure when installing/removing. Tips can be adjusted to
HC desired clamp opening to ensure fast, consistent installation or removal. ONE SIZE FITS ALL.
Specify HAZ-2 for any Rotor Clamp Single wire (HC) hose clamp you are installing.
248 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
Hose Clamp Tools Pneumatic
Pneumatic Hose Clamp Tools
Pneumatic Hose Clamp Tools use a compressed air line of 90 psi, and are activated by a simple lever reducing
stress on the hand from repeated assembly/disassembly. Tangs of the clamp fit in the jaws of the tool and are
compressed for installation or removal on the hose. Helps eliminate carpal tunnel syndrome.
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 249
Retaining Ring Plier Kits
Retaining Ring Plier Kits
Stock the tools you use the most with any or all of these four retaining ring plier kits. Rugged carrying cases
provide portability and durability in a manufacturing/factory environment. Tools are designed to fit a wide range of sizes
from 3/8” to 4” diameter retaining rings, meeting most everyday MRO requirements. Rotor Clip Plier Kits can be easily
stored on a bench or in a maintenance cabinet/storage area. Descriptions and specifications follow.
SH SHI
Convertible Pliers Mini Convertible
SHR BSH Kit (RPK#3) Pliers Kit (RPK#6)
Contains 12 pliers which can be This abbreviated version of the
easily converted from internal to RPK#3 features 6 pliers in straight
**
SHF VSH external and back again. Includes and 90° configurations that will fit
straight, 45° and 90° tip pliers that retaining rings up to 2” in diameter.
** Convertible Plier Kit only
will fit retaining rings up to 2” in diameter. Does the work of 24 Durable plastic case is easily stored in the tightest of spaces.
individual tools!
250 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
Automated Assembly Axial Rings
Automated Assembly is used in the manufacturing process
as a cost reduction tool that additionally achieves increased
production rate and added quality through repeatability. The same
holds true for automated assembly of retaining rings. Parts can
be assembled fast, reducing costs without sacrificing quality.
Properly designed installation equipment shuttles the ring into the
groove without disruption and guards against permanent set
(overstretching/over- compressing of ring) to ensure a tight fit.
Design Considerations
Feed equipment should be designed to work with rings meeting
standard specifications. Most critical is to design equipment that
EXTERNAL INTERNAL
can accommodate the helix and pitch limitations for the type of Use tapered mandrel to expand Use tapered housing to compress
ring you are using. If the equipment is sensitive to any of these ring and install in groove on shaft. ring and install in groove in hous-
factors, it will require special processing that will add to your (Note: angle of inclination of ing. (Note: angle of inclination
costs. Design guidelines include: taper should be 3-5 degrees). of taper should be 3-5 degrees).
1. Consider use of a tapered mandrel for external retaining
rings and a tapered housing for internal retaining rings (see
illustrations). It is not recommended to pick up and transfer
rings by the lug holes.
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 251
Formulas Load Capacities
When there is radial play between the retained part and the
Static Thrust Loads shaft or housing, such play must be treated as though the
retained part had a chamfered corner. The magnitude of the
1. ALLOWABLE THRUST LOADS - RINGS (Pr or P′′r) chamfer should be considered equal to the play. Loading data
for rings abutted by chamfered parts (P′r) as shown in the
Maximum allowable static thrust capacities for rings normally specific ring data charts must be considered. (See CORNER
used with grooves are listed in the data charts for each ring RADII & CHAMFERS, page 257, right column.)
type. The load limits are given for rings (Pr or P′r) and
grooves (Pg). Allowable load capacities for rings (Pr) apply only to standard
thickness rings made of standard materials using the shear
The values for Pr or P′r are applicable only when the ring is strength values listed in Table 1, below, left.
installed in a housing or on a shaft made of hardened steel
where the thrust load capacity of the groove is equal to or When the following special materials are used, multiply the
greater than that of the ring. When the ring is seated in a allowable thrust load of the ring by the conversion factor
groove cut in softer material, and Pg is less than Pr or P′r, shown below.
Pg becomes the limiting factor in the assembly.
252 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
Load Capacities Formulas
Pg = GfDsdπσy
K1Fs
For this example, assume that the edge margin will only be
half the listed catalog value or, y/d=1.5. The above equation
is as follows:
= 1130.4
4.40
= 256.9 lbs.
Maximum thrust load for reduced edge margin
For Technical Assistance,
e-mail tech@rotorclip.com
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 253
Formulas Load Capacities
The allowable load of a part in which a retaining ring groove Formulas for determining ring and groove load limits — with
is cut depends upon the ultimate tensile strength and tensile sample calculations for Series HO internal rings and Series SH
yield strength of the material used, and on the bearing area external rings — are given below. The loads are calculated for
of the ring against the groove wall. For internal rings used in retained parts having sharp corners. Correction factors (Gf)
bores and housings — and external rings assembled on for calculating Pr and Pg are given in Table 2 on right. The
hollow shafts — wall thickness dimension w, illustrated correction factors are based upon the load characteristics of
below, can be calculated from the formulas: the rings.
w = Ds - Dg2 - 3GfDsdσy
2 4 σu
where:
Ds = Shaft or housing dia. (in.)
Dg = Groove dia. (in.) ALLOWABLE THRUST LOAD — RING (Pr in lbs.)
Gf = Correction Factor [See Table 2, Page 255]
d = Groove depth (in.) Pr = Gf Dh T π Ss
σy = Tensile yield strength of groove material (psi) Fs
[See Table 3, Page 258] where:
σu = Ultimate tensile strength of groove material (psi) Gf = Conversion Factor [See Table 2, Page 255]
Dh = Housing dia. (in.)
These formulas provide for a wall thickness that is safe for T = Ring thickness (in.)
allowable groove thrust loads (Pg) calculated with the formula Ss = Shear Strength of ring material (psi)
at the right. If substantially lighter loads will be encountered [See Table 1, Page 252]
and a thinner wall is desired, actual tests are recommended. Fs = Safety factor
254 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
Load Capacities Formulas
ALLOWABLE THRUST LOAD — GROOVE (Pg in lbs.) ALLOWABLE THRUST LOAD — GROOVE (Pg in lbs.)
Pg = (1.2) 2.000 (.061) π 40, 000 = 9200 lbs. > 7000 lbs. Pg = (1) 1.000 (.030) π 45,000 = 2100 lbs. > 2000 lbs
2 2
Pr = Gf Ds T π Ss
Fs
where:
Gf = Conversion Factor [See Table 2, right]
Ds = Shaft dia. (in.)
T = Ring thickness (in.)
Ss = Shear Strength of ring material (psi)
[See Table 1, Page 252]
Fs = Safety factor
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 255
Formulas Load Capacities
This can occur when a surge in thrust load is transmitted to FOR THE GROOVE: Ig = Pgd = 10,400 (.061)
a ring installed in a tight assembly, without play between the
2 2
retained part and the ring. Sudden loads of this nature should
= 320 in. lbs. > 200 in. lbs.
not exceed, at their maximum, 50% of the allowable static
thrust load (Pr or Pg, whichever is lower). 3. VIBRATION LOADING
256 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
Load Capacities Formulas
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 257
Formulas Load Capacities
NOTE: R and Ch cannot exceed the values for Rmax and Chmax
listed in the data charts for the individual ring types.
258 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
Load Capacities Formulas
Ring Seated at
Minimum Depth
If the take-up requirement is satisfied, the groove location
limits (Amin & Amax) can be calculated as follows:
Ring Seated at
Maximum Depth
(Near Groove
Bottom)
The allowable “take-up” capability of a ring is its ability to The groove location limits will be as follows:
compensate for the dimensional variation of the components
in an assembly. Whether a beveled ring can be used in this Amin = 1.002 + .045 + .072/2 (tan 15°) = 1.057
way depends on two factors: Amax = .998 + .043 + .072 (tan 15°) = 1.060
1. The summation of the three relevant tolerances which If the user’s ability to locate the groove requires less than the
determine the take-up required. As can be seen in the drawing .003 allowable tolerance, the maximum seating depth position
(upper right), these parameters are the variation in retained can be moved up the groove to provide a higher minimum
part width (ΔB), groove location (ΔA), and ring beveled edge axial force.
(ΔU). For simplicity of analysis, the groove and ring 15°
angles are assumed to have no variability. Until now, the explanation has focused on a technique
which will assure that 100% of the assemblies will have the
2. The capability of the ring to provide take-up or ring seated within the limits shown. If the user will accept a
compensation for the variability of the assembly components statistically small number of assemblies (2 out of 1000) with
listed above. For the ring to provide sufficient take-up to the ring seating slightly outside of these limits, the statistical
compensate for the variability, and to seat within the limits d/2 groove location technique can be used. This will provide
to d, the following requirement must be satisfied: slightly more take-up than the technique described above.
Please contact the Rotor Clip Engineering Department for
information about this concept.
260 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
Bowed Retaining Rings Formulas
BE Series
Bowed E-Ring
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 261
Inspection Procedures
DETERMINING PERMANENT SET LIMITS DETERMINING PERMANENT SET LIMITS
FOR BASIC EXTERNAL RETAINING RINGS FOR BASIC INTERNAL RETAINING RINGS
SH, VSH, SHI HO, VHO, HOI
1. Measure thickness (designated as "T" in specification 1. Measure thickness (designated as "T" in specification
charts) of the ring for adherence to specified tolerances. charts) of the ring for adherence to specified tolerances.
2. Using a Rotor Clip retaining ring plier, separate the lugs 2. Using a Rotor Clip retaining ring plier, compress the lugs
until the ring barely fits over a shaft 1% larger than the fully until they touch. Repeat this procedure four additional
nominal shaft diameter. Repeat this procedure four additional times using the same ring. Examine the ring for cracks.
times using the same ring. Examine the ring for cracks.
3. Measure ring diameter (D) in three directions as
3. Measure ring diameter (D) in three directions as indicated below.
indicated below.
4. FOR SH AND VSH RINGS - Take the results of these three 4. FOR HO AND VHO RINGS - Take the results of these three
measurements and compute the average. Compare this figure measurements and compute the average. Compare this figure
to the minimum groove diameter listed in the specification to the maximum groove diameter listed in the specification
chart for SH and/or VSH rings. If the average diameter after chart for HO and/or VHO rings. If the average diameter after
permanent set is less than the groove diameter, THEN permanent set is GREATER than the groove diameter, THEN
THE RING IS FULLY FUNCTIONAL AND WILL PERFORM THE RING IS FULLY FUNCTIONAL AND WILL PERFORM
ACCORDING TO STATED SPECIFICATIONS: ACCORDING TO STATED SPECIFICATIONS:
Average Diameter < Minimum Groove Diameter ("Dg" in Spec Average Diameter > Maximum Groove Diameter ("Dg" in
Chart) Spec Chart)
5. FOR SHI RINGS - Take the results of the three diameter 5. FOR HOI RINGS - Take the results of the three diameter
measurements described in #3 above and compute the measurements described in #3 above and compute the
average. Measure the maximum section (“S max” in the average. Measure the maximum section ("S max" in the spec
spec charts). Compare the average diameter minus 2 times charts). Compare the average diameter plus 2 times "S max"
"S max" to the minimum groove diameter listed in the to the maximum groove diameter listed in the specification
specification chart for SHI rings. If the average diameter chart for HOI rings. If the average diameter plus twice the
minus twice the maximum section after permanent set is maximum section after permanent set is GREATER than the
less than the groove diameter, THEN THE RING IS FULLY groove diameter, THEN THE RING IS FULLY FUNCTIONAL AND
FUNCTIONAL AND WILL PERFORM ACCORDING TO STATED WILL PERFORM ACCORDING TO STATED SPECIFICATIONS:
SPECIFICATIONS:
Average Diameter + 2S max > Maximum Groove Diameter
Average Diameter – 2S max < Minimum Groove Diameter ("Dg" in Spec Chart)
("Dg" in Spec Chart)
262 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
Inspection Procedures
LIMITATIONS – DISH, PITCH & BURR
Rotor Clip retaining rings meet accepted industry parameters for limitations of dish and pitch. These characteristics are
illustrated below.
1. DISH LIMITATIONS
Dish is any difference in height occurring from the outer edge of the ring to the inner edge. This
condition should be considered separate from Pitch (see #2). To determine Dish, a small amount
of weight can be applied to the upper surface of the ring to remove pitch from the overall height
measurement.
2. PITCH LIMITATIONS
Pitch takes into account thickness of the ring including any mismatching of lugs,
where applicable.
3. BURR LIMITATIONS
A burr results from the metal stamping process. It is a raised edge for which the
following parameters apply.
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 263
Inspection Procedures
INSPECTION PROCEDURES FOR CONSTANT CONSTANT SECTION RING
SECTION RETAINING RINGS “KICK-IN” FEATURE
Measure the ring for the parameters indicated and compare Constant Section retaining rings become elliptical when
them to the dimensions listed in the specification pages for deformed making three-point contact with the groove (see
that particular ring. NOTE: ALL DIMENSIONS ARE TAKEN drawing). Two of these contact points are the ends, which
IN THE FREE STATE EXCEPT FOR THE GAP, WHICH IS seat deeply into the groove making it extremely difficult to
MEASURED ONCE THE RING IS INSTALLED. install/remove in an application.
*These dimensions are External (USH) ring makes "Kick out" feature makes
measured with the ring three-point contact with the lugs more accessible for
installed in the groove. groove of a shaft. easier installation and
removal.
264 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
Retaining Ring Definitions
Tapered Retaining Rings—Rotor Clip basic rings have a Retaining Ring Pliers—For
tapered section which decreases symmetrically from the retaining rings with lug holes—
center to the free ends. As a result, basic internal and external the tips of these special tools are
rings remain circular when contracted or expanded within the inserted into the lug holes and
limits of normal use. This assures contact with the groove compressed (internal) for instal-
along the entire periphery of the ring (a key factor in obtaining lation in a housing or expanded
high thrust capacity). (external) for installation over a
shaft.
Constant Section Retaining Rings—These rings have a
uniform section height. When they are contracted or Applicators—Used to install radial retaining rings onto a
expanded, they take on an oval deformation (rather than shaft.
circular, like tapered rings). As a result, they contact the
groove bottom at three or more isolated points, but never Dispensers—Dispenses stacked radial retaining rings onto an
continuously around the periphery. applicator.
Spiral Retaining Rings—These Permanent Set—This occurs when a ring has been deformed
make 360 degree contact with beyond its elastic limits and does not return to its original
the groove in a housing or on a condition, resulting in its failure to seat properly in the groove.
shaft. However, they accommo-
date less force than a tapered Thrust Load Capacity—The amount of force a retaining ring
ring and are more will accommodate once installed in a groove.
difficult to install/remove.
Spiral Retaining Rings.
Edge Margin—The distance
Inverted Lugs—Allows more clearance on a shaft or in a from the groove to the end of
housing; the lugs also abut the bottom of the groove. the shaft or housing.
Radial Installation.
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 265
Design Considerations Retaining
Ring
TWO OVERALL RULES FOR SELECTING 3. Load capacity - Maximum allowable static thrust load
THE RIGHT RETAINING RING FOR YOUR capacities for all rings are listed in the catalog pages for all
APPLICATION Rotor Clip rings. If a ring is seated in a groove cut in material
softer than the ring, the thrust load capacity of the groove
1. Consider the ring as an integral part of your design from (“Pg” in the ring data charts) becomes the limiting factor in
original concept through prints and prototypes. If you work the assembly. If the ring is installed in a housing or on a shaft
this way, chances are you’ll be able to use smaller, lighter made of hardened steel, the maximum allowable static thrust
components for substantial cost savings. And you’ll be able load capacity of the ring (Pr) may be used.
to use one of our standard ring designs, which is a lot
more economical than finding later you need an expensive, Importance of load capacity to your design - If you need
custom-designed fastener. rings to position and secure bearings in a pump, or lock up
components in a car or truck transmission, load capacity can
2. Think ahead to the assembly line: how will the ring be be critically important for function, safety and reliability of the
installed - by hand, semi-automatically or with mechanized ring application. On the other hand, if you plan to use a ring
tools - in relation to other manufacturing operations. This can merely to hold a plastic wheel on the axle of a toy truck,
save you a great deal of time and effort, and avoid problems chances are you won’t have to worry about loads on the ring.
when you go into production. All you really need is a ring that will stay put once you have it
positioned. It is pointless to “over design” for high load
BASIC CONSIDERATIONS capacity and pay the price for both rings and grooves when
another ring will do the job less expensively. So take a hard
1. Size - Bore, housing and shaft diameters will determine the look at your load capacity requirements before making any
size of the rings you can use. ring selections. As we indicated earlier, you’ll find everything
you need to know in the Rotor Clip Catalog.
266 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
Retaining
Ring
Design Considerations
5. Types of Axial/Radial Rings - The basic internal/ and How the Bevel Works - When a beveled retaining ring is
external (HO/SH) rings provide heavy thrust load capacities. assembled in its groove, if there is end-play between
components in the assembly, the ring’s spring action causes
• The inverted versions of these rings have lower thrust the fastener to seat deeper in the groove, compensating for
load capacity but provide better clearance and form a higher the end-play. The spring action also exerts an axial force
uniform shoulder good for retaining bearings and other against the retained part which can be calculated with
components with large corner radii or chamfers. formulas given in the Rotor Clip Catalog. Rotor Clip beveled
rings are available only in ring types for axial installation
• Radial rings generally have lower thrust load capacity but
speed assembly where the parts being retained are more 7. To Groove or Not to Groove - Most retaining rings are
accessible; they also form larger shoulders against the designed to be assembled in accurately located grooves
retained parts. These are general rules, however, and there which become an integral part of the fastening system. The
are exceptions; e.g., Series PO and POL retainers are radial groove assures proper location of the ring and contributes
rings with substantially greater gripping strength than some to its load capacity in the assembly. For many products,
axial rings. however, it isn’t practical to cut a groove and in some
designs, you don’t need one. The groove is unnecessary, for
• Series LC two-part interlocking rings were designed example, in many electronic instruments, small appliances,
for high rotational speeds and provide a more attractive toys, plastic products and other applications where the
appearance than some axial types. required shoulder need not absorb any sizable thrust load but
rather must serve merely as a positioning and locking device
against small vibrations and impacts.
6. End-Play Take-Up Rings -
In many products, accumulated Rotor Clip self-locking rings do not require any grooves,
tolerances or wear in the retained threads or other preparatory machining. They may be
parts can cause objectionable installed quickly and economically even by unskilled labor
end-play in the assembly. There and - because they may be seated at any point on a shaft
are two types of rings you can use or in a housing - automatically compensate for accumulated
to avoid this: Rotor Clip bowed Bowed rings, for resilient end- tolerances in the retained parts. Series SHF retainers may be
play take-up, function as both
rings are designed to provide spring and fastener.
removed for product adjustment or service; the other rings
resilient take-up by functioning must be destroyed for disassembly.
as both spring and fastener. In
addition to compensating for
end-play, they also can be used to
dampen vibration and oscillation.
SHF RG TX TY TI DSF
They are available in several
different types for axial or radial
assembly. 8. Assembly and Disassembly - As mentioned earlier, it is
helpful for design engineers to “think ahead” about assembly
Rotor Clip beveled rings provide before specifying retaining rings. That way you can choose
rigid end-play take-up by rings which can be installed quickly and economically with
functioning as a “wedge” between Beveled rings take up end-play Rotor Clip pliers, applicators and dispensers, or other simple
the retained part and the load- rigidly, forming “wedge” hand tools (see pages 242-250). If you are going to design
between part and groove.
bearing groove wall. Series VHO and build you own automate installation equipment, be sure to
beveled rings have a 15° bevel on check with our technical sales department for guidelines that
just one side of the outer circumference. Series VSH external will help you avoid problems after your equipment is put into
rings also have a single bevel which is located on the inner service.
circumference of the ring.
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 267
Military Retaining Rings
ROTOR CLIP OFFERS 100% MILITARY
CERTIFIED RETAINING RINGS
• DFARS Compliant
• CAGE CODE: 07382
• MADE IN USA
Rotor Clip now offers retaining rings certified to
military standards in the popular materials and
finishes listed below:
Lot
Number
Flaking Finish - Look for finish that is flaking off parts. If
you see a similar condition on your retaining rings, contact
your supplier. Wherever the finish is removed, the parts can
potentially rust and fail.
Country of Origin - Like the lot number, this should be
displayed prominently on any packages you receive. YOU
HAVE A RIGHT TO KNOW WHERE YOUR RINGS WERE MADE.
Flaking
Finish
Country of
Origin
Critical Measurements - These include thickness,
Min/Max sections, lug height and hardness. Be sure these
measurements match the print or the Rotor Clip catalog
specifications for that particular part.
Rust - The presence of rust is an indication that the rings
have passed their shelf life and should not be used. Use a
micrometer to
measure the
thickness
Rusty dimension of
Ring your ring
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 269
Joint Design Guide Hose Clamps
B. The outside diameter depends on the wall thickness, A. Factors to consider when sizing a clamp:
which varies depending upon the hose type and construction.
It is important to specify a hose with a closely controlled wall • CTB type clamps: The clamps have a number designation
thickness, the smaller the tolerance the better. This will aid in equivalent to the outside diameter of the joint to be clamped,
sizing the clamp for the application. expressed in millimeters (Ex.-CTB-27).
C. Constant tension type clamps transmit force more easily • HC (SAE Type “E”), HW and DW (SAE type CTW) - Clamps
through a hose with a thin cross section. have a range of recommended application diameters, listed
in the catalog as ”A”, “B” and “C” diameters. The nominal
D. A higher hose durometer (hardness) means the hose is diameter of the clamp is the clamp size divided by 16.
less compliant and more difficult to install. Lower durometer
hoses allow the clamp to translate its force directly to the • The joint diameter will equal the fitting outside diameter plus
sealing surface of the fitting. twice the wall thickness, including the tolerances associated
with each.
E. The straighter the angle of the hose, the easier it is to
install. • The clamp must be large enough to fit over the
maximum diameter of the joint bead and hose at this point
The Society for Automotive Engineers recognizes two basic (see illustration above).
types of hoses for heater and radiator applications. They
are described below. (For more detailed explanation of B. You can use a smaller clamp on an application to increase
these and other hose types, see SAE specification J20.) force. This can be done by placing the clamp on the fitting,
installing the hose and sliding the clamp “backwards” up to
A. SAE 20R3 Heater Hose - Used for heater systems in the bead.
ground transportation vehicles. Wall thickness range: for sizes
less than 25.4mm, the OD is the target ID +8mm (total wall), C. Ideally, a clamp should be sized to fit onto the joint when
±0.8mm. For 25.4mm size, the OD is 34mm±1.2mm. opened to 90% of full (as a safety factor) and close to no less
than the nominal (size) diameter when in the final position.
270 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
Hose Clamps Joint Design Guide
III. FITTING IV. ASSEMBLY
The fitting is the portion of the joint over which the hose
is installed. To reap the full benefits of a constant tension • Clamps should be installed with specific pliers
clamp joint, the fitting should have the following recommended for the type of clamp being used.
characteristics:
• Expansion of the clamp beyond the intended
A. The fitting should be round (within .003 inches). operating diameter will diminish the force that the
clamp can apply.
B. There should be interference between the fitting and the
hose, typically between 5% and 10% of the hose inner • Any lubricating substance used to aid assembly of the
diameter. (Ex. A 1” nominal diameter hose could have a hose must never be in contact with the clamp.
1.062” diameter fitting for a 6.2% interference fit. All
tolerances should be considered when calculating this • Such lubricants in contact with a clamp can enable
diameter.) a mechanism for hydrogen migration, causing failure
through material fracture.
C. The surface of the fitting should be free of pits, scratches,
"dents," parting line mismatches, and any surface defect that • Examples of lubricants known to cause clamp failure
might cause a leak. include acetone, chlorine, flourine, mineral oil, dish
detergents, and laundry detergents.
D. The fitting should contain a bead that will prevent
slippage under conditions of pressure where the hose is
not constrained.
For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com 271
www.rotorclip.com
NOTES 1.800.557.6867 • +1 732.469.7333 • sales@rotorclip.com
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
272 For the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
ROTOR CLIP Trademarks
TRUARC ®
®
Rot
orCl
ipCompany
,Inc.
® -Wor
ldHeadquar
ter
s
187Dav idsonAvenue,Somerset,NJ08873
1-800-557-6867•+1732- 469-7333•Fax:+1732-
469-
7898
www. r
otorcl
ip.
com
Rot
orCl
ipLi
mit
ed®
Uni
t6,Meadowbr ookPark,Holbr
ook,Shef
fi
el
d,S203PJUni
tedKi
ngdom
+44(0)1142473399•Fax :+44(0)1142474499
e-
mail
:rcl
td@rotorcl
i
p.com
www.r
otorcl
i
p.co.uk
Rot
orCl
ipGmbH®
Buchwiese3,D-65510Idstei
n/T
aunus Ger
many
+49(0)6126227360•Fax :+49(0)61262273619
e-
mail
:rcgmbh@r ot
orcl
i
p.com
www.rotor
cli
p.
de
Rot
orCl
ipCzec
ha.
s.
Pražská403,CZ-41
118BudyněnadOhří
+420416863168•Fax:+420416863193•e-
mai
l
:rot
orc
li
pcz
@rot
orc
li
p.c
om
www. segnor
.cz
Rot
orCl
ipShanghaiRepOf
fice
Room 1510~1511,JHPlaza,2008Huqi
ngpingRoad
Shanghai
,201702 Peopl
e'
sRepubli
cofChina
Tel
:0017324697333*4101
Mobil
e:+8613601784145
www.rot
orcl
i
p.com