Professional Documents
Culture Documents
Ha Oct 2014.docxha Oct 2014
Ha Oct 2014.docxha Oct 2014
in)
Heavy Aero plane OCT 2014
2. Which method may be used to inspect fiberglass/honeycomb structure for entrapped water?
1. Acoustic emission
2. X-ray
3. Back lighting
a) 1 and 2
b) 1 and 3
c) 2 and 3
3. One method of inspecting a laminated fiberglass structure that has been subjected to damage is to
a) Strip the damaged area of all paint and show a strong back light through structure.
b) Use dye-penetrant inspection
c) Use eddy current probe on both sides of damage.
4. What is the material layer used within the vaccum bag pressure system to absorb excess resin during curing called?
a) Release
b) Bleeder
c) Breather
14. The elevators of a conventional airplane are used to provide rotation about
a) Longitudinal axis b) lateral axis c) vertical axis
15. If the wing of a monoplane is improperly rigged to a greater angle of incidence than designed ,it will cause
a) Airplane to be off balance both laterally and directionally.
Share your documents with us at (aviatorslinks@gmail.com) DownloadOur Mobile App For Recent Papers Page 1
Aviation World (www.dgcaquestionpapers.in)
b) Airplane to pitch and roll about lateral axis
c) Right wing to have both increased lift and drag.
17. When used near magnetic compass, cotter pins are made of
a) Anodized Al alloy b) Corrosion resistance steel c) Cd plated low carbon steel
18. A tension regulator in the flight control cable system of large all metal aircraft is to
a) Provide a means of changing cable tension in flight
b) Retain a set tension
c) Increase a cable tension in cold weather.
21. During weight and balance check of heavy airplane the most adverse condition can be achieved by loading the aircraft in
a) Max.gross weight
b) Forward adverse condition
c) Rearward adverse condition
d) All the above.
24. The preload pressure of the accumulator will be ______ as the system pressure
a) Same b)twice c)One third d)half
26. The crack detection method which is used to find the defects developed in such parts as turbine shaft, vanes…etc
a) Magnetic inspection
b) Liquid penetration method
c) Eddy current method
d) Ultra sonic test
27. In vapor cycle system, cabin air loses heat and get cooled when passing through
a) Evaporator
b) Condenser
Share your documents with us at (aviatorslinks@gmail.com) DownloadOur Mobile App For Recent Papers Page 2
Aviation World (www.dgcaquestionpapers.in)
c) Expansion valve
34. When the aircraft is on ground, all positive pressure in the cabin is discharged out by
a) Outflow value
b) positive pressure valve
c) Dump valve
d) safety valve
35. The design which allows the operation of a component when one member of a complex structure fails, some other member
would assume the load of the failed component – is called
a) Fail safe b) safe life c) Damage tolerant
38. The check carried out to determine whether the aircraft components are properly aligned or not
a) Rigging check b) Alignment check c) Symmetry check
Share your documents with us at (aviatorslinks@gmail.com) DownloadOur Mobile App For Recent Papers Page 3
Aviation World (www.dgcaquestionpapers.in)
c) Apparent turn towards south
41. Which valve installed in hydraulic system will have the highest pressure setting
a) Thermal relief valve b) pressure relief valve c) Main relief valve
43. A pressure operated flow control valve in hydraulic system which is used to operate two components in a sequence after
completing one component actuation.
a) Priority valve
b) Sequence valve
c) Orifice check valve
44. In an aircraft all three hydraulic system pressure became low in flight due to engine failure. Emergency pressure is supplied
to the system automatically by
a) Electric Motor driven pump
b) EDP
c) Accumulator pressure
48. The point in a boundary layer at which laminar airflow changes to turbulent flow is known as
a) Transition Point
49. For fast detection of fires, which fire detector(s) is/are used
a) Rate of rise type
b) Radiation type
c) Overheat detectors
d) All the above
51. After welding steel tubes, it is heated above its upper critical point and allowed to cool in air to relieve internal stress. This
process is called?
a) Tempering b) Hardening c) Annealing d) Normalizing
52. In subsonic flow, when passes through a convergent duct, its Pressure_________ Velocity ______ and density _________
a) Increases, decreases, remains same
b) Decreases, increases, remains same
c) Decreases, increases, decrease.
53. Seals used in Oil hose, tank linings for aromatic aviation gasoline, gaskets..etc are made up of
a) Buna-N b) neoprene c) Thiokol
Share your documents with us at (aviatorslinks@gmail.com) DownloadOur Mobile App For Recent Papers Page 4
Aviation World (www.dgcaquestionpapers.in)
55. Which valve is used to isolate normal hydraulic power and allow emergency pneumatic power to operate brakes?
a) Shuttle valve b)isolation valve c) check valve
56. In capacitance type fuel quantity gauge, capacitance of fuel dependence upon
a) Area of plates
b) Length of the plates
c) Area of the tank
d) All the above
57. Aircraft that has flown through severe turbulence should be inspected for
A) Wing to fuselage joint, tail to fuselage joint, engine mountings and all areas which are expected to have bending loads.
60. To prevent rapid extension of an oleo shock strut, after initial compression resulting from landing impact
a) Various types of valves or orifices are used to restrict the reverse fluid flow
b) the air is forced through a restricted orifice in reverse direction
c) The metering pin gradually reduces the size of the orifice as the shock strut extends.
61. Power boost brake systems are used on aircraft that have
a) High landing speeds
b) Low normal hydraulic system pressure
c) More than one brake assembly per axle.
62. An automatic dampening action occurs at the steer damper if for any reason the flow of high-pressure fluid is removed from
the
a) outlet of the steer damper
b) inlet of the steer damper
c) Replenishing check valve.
63. If the extended longitudinal axis of the main landing gear wheel assemblies intersects aft of the aircraft, the wheels can be
termed as having
a) Toe-In
b) Toe-Out
c) Negative camber
66. on most aircraft, the oil level of an air and oil shock strut is checked by
a) Removing the oil filler plug and inserting a gauge.
b) Measuring the length of the strut extension with a certain air pressure in the strut.
c) Releasing the air and seeing that the oil is to the level of the filler plug.
67. An aircraft pneumatic system, which incorporates an engine driven multistage reciprocating compressor, also requires
a) An oil separator
b) A surge chamber
c) A moisture separator.
68. In an air cycle machine, moisture and water in the bleed air is collected after downstream of the expansion turbine
a) Water separator
Share your documents with us at (aviatorslinks@gmail.com) DownloadOur Mobile App For Recent Papers Page 5
Aviation World (www.dgcaquestionpapers.in)
69. Engine bleed air is conditioned before entering to aircraft cabin by____________ machine
a) Air cycle
b) Vapor cycle
c) Otto cycle
70. Phosphate ester base hydraulic fluid is very susceptible to contamination from
a) Teflon seal material
b) Ethylene-elastomers
c) Water in atmosphere
71. Which of the following lists only desirable properties of a good hydraulic fluid?
a) Low viscosity, chemical stability, high flash point, high fire point
73. If an a/c constant pressure hydraulic system cycles more frequently than usual and no fluid leakage can be detected, the
most probable cause is
a) A too high relief valve setting c) low accumulator preload
b) A pump volume output too high
76. The air that is expended and no longer needed when an actuating unit is operated in a pneumatic system is
a) Exhausted or dumped, usually overboard.
77. In a typical high pressure pneumatic system, if the moisture separator does not vent accumulated water when the
compressor shuts down, a likely cause is a
a) Saturated chemical dryer b) Malfunctioning pressure transmitter
b) Malfunctioning solenoid dump valve.
78. Which is generally used in pressurized aircraft as an emergency back up of Oxygen that is efficient and require least
maintenance?
a) Chemical oxygen candle c) high pressure O2 system
b) Low pressure O2 system
79. The condition of the refrigerant as it enters the condenser of a vapor cycle system will be of _______pressure_________?
a) High, liquid c) High, vapor
b) Low, liquid
80. The electronic type fuel quantity indicating system consists of a bridge cicuit
a) An amplifier, an indicator, and a tank unit
b) A tank, an amplifier, an indicator
c) A tank unit, a tank, an amplifier
81. What will be the indication in cockpit during landing gear operation?
a) Red for unsafe gear, green for down and locked, No light for up & locked
82. In a brake antiskid system, when an approaching skid is sensed, an electrical signal is sent to the skid control valve which
a) Relieves hyd.pressure from brakes
b) Acts as a bypass for the de-booster cylinders
c) Equalize the hyd.pressure in adjacent brakes.
Share your documents with us at (aviatorslinks@gmail.com) DownloadOur Mobile App For Recent Papers Page 6
Aviation World (www.dgcaquestionpapers.in)
84. A typical take off warning indication system, in addition to throttle setting, monitors the position of
a) Elevators, speed brakes, flaps, horizontal stabilizer trim.
86. When an airplane’s primary flight control surfaces are set for a particular phase of flight, such as landing or take off, the
corresponding control-surface indicating system will show
a) Trim position
87. When a landing gear safety switch on a main strut closes at lift off, which system is deactivated
a) Landing gear position system c) Antiskid system
b) Aural warning system
88. What maintains normal windshield temperature control in an electrically heated windshield system?
a) Thermistors
89. MTCS
a) Horizon bar is below the miniature aircraft during climb
91. Elevator is moved up with the help of trim tab for Nose up, trailing edge of the tab will be
a) Upwards relative to the surface.
94. When the rivet is excessively strong in shear, what occurs in the sheet metal at the edge of the rivet hole?
a) Bearing failure
97. A tab which does not move along with flight control surfaces on flight
a) Trim tab c) servo tab
b) Balance tab d)spring tab
Reference
1. Jeppsen airframe text book
2. Jeppesen test guide
3. AC 65-15A
4. AC 65-9A
5. AMR
6. Aircraft basic science
Share your documents with us at (aviatorslinks@gmail.com) DownloadOur Mobile App For Recent Papers Page 7