Professional Documents
Culture Documents
Sewatec / Sewabloc
50 / 60 Hz
DIN / IEC motors
All rights reserved. The contents provided herein must neither be distributed, copied, reproduced,
edited or processed for any other purpose, nor otherwise transmitted, published or made available to
a third party without the manufacturer's express written consent.
Contents
3
Contents
4
Waste Water
Dry-installed Volute Casing Pump
Sewatec / Sewabloc 5
Waste Water
Dry-installed Volute Casing Pump
E impeller:
Product benefits
Closed single- Suitable for the following ▪ Variable hydraulic systems
channel impeller fluids: The right impeller with optimum efficiency for every fluid.
(impeller type E) fluids containing solid High operating reliability due to wide free passages.
substances and long fibres
▪ Double mechanical seal in tandem arrangement with
external liquid feed makes for high operating reliability.
F impeller: ▪ Low maintenance thanks to grease-packed rolling element
bearings sealed for life
Free-flow Suitable for the following
▪ Standardised components are interchangeable within the
impeller fluids:
Sewatec/Sewabloc and Amarex KRT series, so spare parts
(impeller type F) fluids containing solids and
inventories can be optimised and costs reduced.
stringy material as well as
fluids with entrapped air or
gas
Acceptance tests / Guarantees
D, E and F impellers are suitable for handling the following ▪ Each pump is subjected to a performance test to KSB
fluids: Standard ZN 56535.
▪ Activated sludge ▪ Operating data is guaranteed to DIN EN ISO 9906 / 2 / 2B.
▪ Digested sludge
Acceptance tests
▪ Heating sludge
▪ Acceptance tests to ISO/DIN or comparable standards are
▪ Mixed water
available against a surcharge.
▪ Raw waste water
▪ Raw sludge Quality assurance
▪ Recirculated sludge ▪ Quality is assured by means of an audited and certified
Bearings quality assurance system to DIN EN ISO 9001.
Sewatec (bearing brackets S01, S02, S03, S04):
6 Sewatec / Sewabloc
Waste Water
Dry-installed Volute Casing Pump
1) For any fluids which are not listed in this table contact KSB.
2) The first impeller type listed should be given preference.
3) Contact KSB.
4) Severe hydroabrasive wear occurs if solids contents of approx. 0.5 g/l or higher are combined with circumferential speeds
exceeding 20 m/s or low-flow conditions to the left of the duty point.
5) The hydrocarbons mentioned may occur in very high concentrations due to the difference in specific weight and their low
solubility. If this is the case, contact KSB.
6) The required material variants highly depend on the operating hours, rotational speed and flow velocity.
Sewatec / Sewabloc 7
Waste Water
Dry-installed Volute Casing Pump
Shaft seal
Available shaft seal types per bearing bracket
Bearing Standard design Standard variant7)
bracket
Mechanical seal with Stationary mechanical seal Inboard mechanical seal Gland packing
Sewabloc
Sewatec
elastomer bellows (NBR, with spring outside of fluid with covered spring9)
optional: Viton)8) (Cartex S10 cartridge seal)
S01 – ✘ - ✘ -
– B01 ✘ - - -
S02 – ✘ - ✘ -
– B02 ✘ - - -
S03 – ✘ - ✘ -
– B03 ✘ - - -
S04 – ✘ - ✘ -
S05 – ✘ - ✘ ✘
S06 – ✘ - - ✘
S07 – ✘ - - ✘
S08 – - ✘ - ✘
1) For any fluids which are not listed in this table contact KSB.
2) The first impeller type listed should be given preference.
7) A surcharge and longer delivery times apply to standard variants.
8) For all types of waste water
9) For very abrasive fluids or fluids containing metallic particles (e.g. shavings from drilling)
8 Sewatec / Sewabloc
Waste Water
Dry-installed Volute Casing Pump
Sewatec / Sewabloc 9
Waste Water
Dry-installed Volute Casing Pump
10 Sewatec / Sewabloc
Waste Water
Dry-installed Volute Casing Pump
Sewatec / Sewabloc 11
Waste Water
Dry-installed Volute Casing Pump
12 Sewatec / Sewabloc
Waste Water
Dry-installed Volute Casing Pump
Sewatec / Sewabloc 13
Waste Water
Dry-installed Volute Casing Pump
2900 1450 960 725 1750 1160 875 1450 960 725 580 480 1160 875 700 585
20) Selection for a fluid density of 1.0 kg/dm³; higher densities on request only
21) For higher densities up to 1.2 kg/dm³ max.: refer to the corresponding table to select the impeller diameter per bearing
bracket and speed.
14 Sewatec / Sewabloc
Waste Water
Dry-installed Volute Casing Pump
Sewabloc
Sewatec
2900 1450 960 725 1750 1160 875 1450 960 725 580 480 1160 875 700 585
Sewatec / Sewabloc 15
Waste Water
Dry-installed Volute Casing Pump
2900 1450 960 725 580 480 1750 1160 875 700 585 2900 1450 960 725 1750 1160 875 700
22) Selection for a fluid density of 1.0 kg/dm³; higher densities on request only
23) For higher densities up to 1.2 kg/dm³ max.: refer to the corresponding table to select the impeller diameter per bearing
bracket and speed.
16 Sewatec / Sewabloc
Waste Water
Dry-installed Volute Casing Pump
Sewabloc
Sewatec
2900 1450 960 725 580 480 1750 1160 875 700 585 2900 1450 960 725 1750 1160 875 700
Sewatec / Sewabloc 17
Waste Water
Dry-installed Volute Casing Pump
18 Sewatec / Sewabloc
Waste Water
Dry-installed Volute Casing Pump
Material variants
Overview of available materials
Part No. Description Material variant
G G1 G2 GH GC
101 Pump casing EN-GJL-250
135 Wear plate36) EN-GJL-25037) -
163 Discharge cover EN-GJL-250 EN-GJN-HB555 1.4517
183 Support foot Steel38)
210 Shaft 1.4021 1.4462
230 Impeller EN-GJL-250 1.4517 EN-GJN-HB555 1.4517
330 Bearing bracket EN-GJL-250
433 Mechanical seal SiC/SiC (Q1Q1 PGG)
502.01 Casing wear ring EN-GJL-25039) EN-GJL-250 (F impeller only)
VG 434
503 Impeller ring VG 434
452.01 Gland follower40) EN-GJS-400-15
454.01 Stuffing box ring40) EN-GJL-250
456.01 Neck bush40) EN-GJL-250
458.01 Lantern ring40) PTFE
524.01 Shaft protecting 1.4021
sleeve40)
914 Impeller screw Stainless steel41) Stainless steel
902/920 Screws, bolts and
nuts
Screw plugs Steel
Sealing elements NBR
Comparison of materials This type of carbon steel is resistant to cavitation, has excellent
strength values and is used for high circumferential speeds. An
EN ASTM
excellent resistance to pitting corrosion makes ferritic-
EN-GJL-250 A 48 Class 35 B austenitic stainless carbon steel a popular choice for pumping
EN-GJS-400-15 A 536 Class 60–40–18 acidic waste water with a high chloride content as well as
EN-GJN-HB555 A 532 Class II Type B (15 % Cr-Mo) seawater and brackish water. Thanks to its good chemical
1.4517 A 890 CD4MCuN resistance, e.g. also against waste water containing
1.4021 A 276 Type 420 phosphorous and sulphuric acid, this material is used in a wide
1.4462 A 182 F51 range of applications in the chemical industry and and process
engineering. Pumps made of duplex stainless steel have a very
VG 434 -
long service life, even when handling brines, chemical waste
C 35 E A 29 Gr. 1035 water (pH value 1 - 12), grey water and landfill leachate.
Wear-resistant white cast iron (EN-GJN-HB555 (XCR14) or
Description of materials technically equivalent material)
Grey cast iron EN-GJL-250 (lamellar graphite cast iron): This is a wear-resistant white cast iron for highly abrasive fluids
Lamellar graphite cast iron to EN 1561 is the most widely used containing sand, ash or iron ore sinter. It has a Rockwell
cast material for handling municipal sewage, waste water and hardness of 61.5 to 68, which is higher than that of hardened
sludges as well as stormwater and surface water. It is suitable chrome steel. Owing to its hardness, the chromium-
for neutral fluids which are only slightly aggressive and cause molybdenum alloy cast iron features a notably higher wear
little wear. The pH value should be ≥ 6.5, the sand content resistance than EN-GJL-250 grey cast iron and other cast
≤ 0.5 g/l. materials.
Duplex stainless steel (1.4517 or technically equivalent
material)
Sewatec / Sewabloc 19
Waste Water
Dry-installed Volute Casing Pump
Technical data
K impeller
Overview
Size Bearing Pump data K impeller
bracket Shaft seal Pressure limits Inspection
hole diameter
based on water
Suction nozzle
Mechanical seal
Gland packing
Casing
Sewabloc
Sewatec
[mm] [mm] [Nm/rad] [bar] [bar] [mm] [mm] [mm] [mm] [mm] [kgm2]
050-250 S01 - 65 50 13.000 - ✘ 10 15 - 80 3 15 260 150 0,05
050-250 - B01 65 50 13.000 - ✘ 10 15 - 80 3 15 260 150 0,05
050-251 S02 - 65 50 50.000 - ✘ 10 15 - 80 3 15 256 150 0,05
050-251 - B02 65 50 50.000 - ✘ 10 15 - 80 3 15 256 150 0,05
065-250 S01 - 80 65 13.000 - ✘ 6 9 - 80 2 50 230 170 0,08
065-250 - B01 80 65 13.000 - ✘ 6 9 - 80 2 50 230 170 0,08
080-250 S01 - 100 80 13.000 - ✘ 6 9 - 120 2 71 235 205 0,08
080-250 - B01 100 80 13.000 - ✘ 6 9 - 120 2 71 235 205 0,08
080-315 S03 - 100 80 80.000 - ✘ 10 15 - 120 2 33 220 140 0,07
080-315 S05 - 100 80 220.000 - ✘ 10 15 - 120 2 33 220 140 0,07
080-315 - B03 100 80 80.000 - ✘ 10 15 - 120 2 33 220 140 0,07
100-250 S01 - 100 100 50.000 - ✘ 6 9 118 120 2 71 256 210 0,07
100-250 - B01 100 100 50.000 - ✘ 6 9 118 120 2 71 256 210 0,07
100-251 S02 - 100 100 50.000 - ✘ 6 9 118 120 2 71 256 235 0,07
100-251 - B02 100 100 50.000 - ✘ 6 9 118 120 2 71 256 235 0,07
100-400 S04 - 150 100 190.000 - ✘ 10 15 100 150 2 76 408 355 1,1
100-400 S05 - 150 100 220.000 ■ ✘ 10 15 100 150 2 76 408 355 1,1
100-401 S04 - 125 100 190.000 - ✘ 10 15 120 120 2 50 404 310 0,50
100-401 S05 - 125 100 220.000 ■ ✘ 10 15 120 120 2 50 404 310 0,50
125-315 S03 - 125 125 80.000 - ✘ 6 9 118 120 2 76 312 235 0,09
125-315 - B03 125 125 80.000 - ✘ 6 9 118 120 2 76 312 235 0,09
150-315 S03 - 150 150 80.000 - ✘ 6 9 118 150 2 76 310 235 0,18
150-315 - B03 150 150 80.000 - ✘ 6 9 118 150 2 76 310 235 0,18
150-400 S04 - 200 150 190.000 - ✘ 10 15 100 200 3 76 404 300 0,83
150-400 S05 - 200 150 220.000 ■ ✘ 10 15 100 200 3 76 404 300 0,83
150-401 S04 - 150 150 190.000 - ✘ 10 15 120 200 2 76 404 330 0,916
150-401 S05 - 150 150 220.000 ■ ✘ 10 15 120 200 2 76 404 330 0,916
150-401 S06 - 150 150 370.000 ■ ✘ 10 15 120 200 2 76 404 330 0,916
151-401 S05 - 150 150 220.000 ■ ✘ 10 15 120 200 3 80 408 380 0,52
150-500 S05 - 150 150 220.000 ■ ✘ 10 15 118 150 3 60 504 350 0,71
150-500 S06 - 150 150 370.000 ■ ✘ 10 15 118 150 3 60 504 350 0,71
200-315 S03 - 200 200 80.000 - ✘ 6 9 118 200 3 70 295 210 0,22
200-315 - B03 200 200 80.000 - ✘ 6 9 118 200 3 70 295 210 0,22
200-316 S03 - 200 200 80.000 - ✘ 6 9 118 200 2 100 305 230 0,22
200-316 - B03 200 200 80.000 - ✘ 6 9 118 200 2 100 305 230 0,22
200-330 S04 - 250 200 190.000 - ✘ 10 15 118 200 3 70 326 270 0,35
200-330 S05 - 250 200 220.000 ■ ✘ 10 15 118 200 3 70 326 270 0,35
200-400 S04 - 200 200 190.000 - ✘ 10 15 200 200 3 80 404 330 0,52
200-400 S05 - 200 200 220.000 ■ ✘ 10 15 200 200 3 80 404 330 0,52
200-400 S06 - 200 200 370.000 ■ ✘ 10 15 200 200 3 80 404 330 0,52
200-402 S04 - 200 200 190.000 ■ ✘ 10 15 140 200 3 80 408 300 0,52
200-402 S05 - 200 200 220.000 ■ ✘ 10 15 140 200 3 80 408 300 0,52
200-500 S05 - 200 200 220.000 ■ ✘ 10 15 118 200 3 75 504 400 0,83
200-500 S06 - 200 200 370.000 ■ ✘ 10 15 118 200 3 75 504 400 0,83
200-500 S07 - 200 200 1.020.000 ■ ✘ 10 15 118 200 3 75 504 400 0,83
20 Sewatec / Sewabloc
Waste Water
Dry-installed Volute Casing Pump
based on water
Suction nozzle
Mechanical seal
Gland packing
Casing
Sewabloc
Sewatec
[mm] [mm] [Nm/rad] [bar] [bar] [mm] [mm] [mm] [mm] [mm] [kgm2]
200-501 S06 - 250 200 370.000 ■ ✘ 10 15 200 200 2 100 502 400 1,68
200-631 S07 - 250 200 1.020.000 ■ ✘ 10 15 140 200 2 105 622 480 4,41
200-631 S08 - 250 200 1.400.000 ■ ✘ 10 15 140 200 2 105 622 480 4,41
250-400 S04 - 250 250 190.000 - ✘ 10 15 143 200 3 85 370 330 0,5
250-400 S05 - 250 250 220.000 ■ ✘ 10 15 143 200 3 85 370 330 0,5
250-400 S06 - 250 250 370.000 ■ ✘ 10 15 143 200 3 85 370 330 0,5
250-401 S04 - 250 250 190.000 - ✘ 10 15 143 200 2 105 404 310 0,56
250-401 S05 - 250 250 220.000 ■ ✘ 10 15 143 200 2 105 404 310 0,56
250-630 S07 - 250 250 1.020.000 ■ ✘ 10 15 143 143 4 90 630 500 2,76
250-630 S08 - 250 250 1.400.000 ■ ✘ 10 15 143 143 4 90 630 500 2,76
250-900 S09 - 350 250 2.500.000 ■ ✘ 13 19,5 100 - 3 110 840 717 19,03
300-400 S04 - 300 300 190.000 - ✘ 10 15 143 200 3 100 388 332 0,75
300-400 S05 - 300 300 220.000 ■ ✘ 10 15 143 200 3 100 388 332 0,75
300-400 S06 - 300 300 370.000 ■ ✘ 10 15 143 200 3 100 388 332 0,75
300-401 S04 - 300 300 190.000 - ✘ 10 15 143 200 2 135 408 367 0,75
300-401 S05 - 300 300 220.000 ■ ✘ 10 15 143 200 2 135 408 367 0,75
300-500 S06 - 300 300 370.000 ■ ✘ 6 9 143 200 3 100 504 430 1,48
300-500 S07 - 300 300 1.020.000 ■ ✘ 6 9 143 200 3 100 504 430 1,48
350-500 S06 - 350 350 370.000 ■ ✘ 6 9 143 200 3 110 508 393 3,12
350-500 S07 - 350 350 1.020.000 ■ ✘ 6 9 143 200 3 110 508 393 3,12
350-501 S06 - 350 350 370.000 ■ ✘ 6 9 143 200 2 170 509 490 3,00
350-501 S07 - 350 350 1.020.000 ■ ✘ 6 9 143 200 2 170 509 490 3,00
350-630 S07 - 350 350 1.020.000 ■ ✘ 10 15 143 200 3 135 630 500 5,22
350-630 S08 - 350 350 1.400.000 ■ ✘ 10 15 143 200 3 135 630 500 5,22
350-710 S07 - 350 350 1.020.000 ■ ✘ 10 15 143 200 3 110 730 580 10,6
350-710 S08 - 350 350 1.400.000 ■ ✘ 10 15 143 200 3 110 730 580 10,6
400-500 S06 - 400 400 370.000 ■ ✘ 6 9 200 200 3 130 508 355 3,37
400-500 S07 - 400 400 1.020.000 ■ ✘ 6 9 200 200 3 130 508 355 3,37
400-630 S08 - 500 400 1.400.000 ■ ✘ 6 9 200 200 3 132 620 400 8,21
400-710 S09 - 500 400 2.500.000 ■ ✘ 10 15 150 - 3 165 739 587 16,0
400-820 S09 - 500 400 2.500.000 ■ ✘ 13 19,5 143 - 3 130 830 659 17,79
500-630 S07 - 500 500 1.020.000 ■ ✘ 4 6 200 200 3 133 582 490 6,11
500-630 S08 - 500 500 1.400.000 ■ ✘ 4 6 200 200 3 133 582 490 6,11
500-900 S09 - 600 500 2.500.000 ■ ✘ 9 13,5 200 - 3 202 908 721 45,0
500-900 S10 - 600 500 5.000.000 ■ ✘ 9 13,5 200 - 3 202 908 721 45,0
500-632 S08 - 500 500 1.400.000 ■ ✘ 4 6 200 200 3 135 639 560 6,00
500-710 S09 - 500 500 2.500.000 ■ ✘ 8/6,9 6,9/9,0 200 - 3 150 700 586 16,0
600-520 S07 - 500 600 1.020.000 ■ ✘ 4 6 200 200 3 145 532 457 7,02
600-710 S08 - 600 600 1.400.000 ■ ✘ 4 6 200 200 3 165 736 664 16,96
600-900 S10 - 700 600 5.000.000 ■ ✘ 9 13,5 200 - 3 180 908 760 50,0
700-900 S08 - 700 700 1.400.000 ■ ✘ 3 4,5 200 200 3 190 850 638 40,0
Sewatec / Sewabloc 21
Waste Water
Dry-installed Volute Casing Pump
D impeller
Overview
Size Bearing Pump data D impeller
bracket Shaft seal Pressure limits Inspection
hole diameter
based on water
Suction nozzle
Mechanical seal
Gland packing
Casing
Sewabloc
Sewatec
[mm] [mm] [Nm/rad] [bar] [bar] [mm] [mm] [mm] [mm] [mm] [kgm2]
080-315 S03 - 100 80 80.000 - ✘ 10 15 - 120 1 70 260 242 0,124
080-315 S05 - 100 80 220.000 - ✘ 10 15 - 120 1 70 260 242 0,124
080-315 - B03 100 80 80.000 - ✘ 10 15 - 120 1 70 260 242 0,124
080-316 S03 - 125 80 80.000 - ✘ 10 15 - 120 1 70 306 280 0,222
080-316 - B03 125 80 80.000 - ✘ 10 15 - 120 1 70 306 280 0,222
100-251 S02 - 150 100 50.000 - ✘ 6 9 118 120 1 76 265 234 0,115
100-251 - B02 150 100 50.000 - ✘ 6 9 118 120 1 76 265 234 0,115
100-315 S05 - 125 100 220.000 - ✘ 10 15 100 120 1 75 222 196 0,065
100-316 S03 - 150 100 80.000 - ✘ 10 15 100 150 1 85 306 270 0,223
100-316 - B03 150 100 80.000 - ✘ 10 15 100 150 1 85 306 270 0,223
150-251 S02 - 150 150 50.000 - ✘ 6 9 120 150 1 100 254 225 0,150
150-251 - B02 150 150 50.000 - ✘ 6 9 120 150 1 100 254 225 0,150
150-315 S03 - 150 150 80.000 - ✘ 6 9 118 150 1 100 317 280 0,289
150-315 - B03 150 150 80.000 - ✘ 6 9 118 150 1 100 317 280 0,289
150-400 S05 - 200 150 220.000 ■ ✘ 10 15 100 200 1 100 363 326 0,573
150-401 S05 - 250 150 220.000 ■ ✘ 10 15 120 200 1 110 412 370 0,999
150-401 S06 - 250 150 370.000 ■ ✘ 10 15 120 200 1 110 412 370 0,999
200-315 S03 - 200 200 80.000 - ✘ 6 9 118 200 1 100 315 280 0,261
200-315 - B03 200 200 80.000 - ✘ 6 9 118 200 1 100 315 280 0,261
200-400 S05 - 250 200 220.000 ■ ✘ 10 15 125 200 1 100 402 355 0,825
200-400 S06 - 250 200 370.000 ■ ✘ 10 15 125 200 1 100 402 355 0,825
250-400 S05 - 250 250 220.000 ■ ✘ 10 15 143 200 1 120 375 320 0,653
250-400 S06 - 250 250 370.000 ■ ✘ 10 15 143 200 1 120 375 320 0,653
300-400 S05 - 300 300 220.000 ■ ✘ 10 15 143 200 1 150 408 375 0,925
300-400 S06 - 300 300 370.000 ■ ✘ 10 15 143 200 1 150 408 375 0,925
22 Sewatec / Sewabloc
Waste Water
Dry-installed Volute Casing Pump
F impeller
Overview
Size Bearing Pump data F impeller
bracket Shaft seal Pressure Inspection
limits hole
diameter
based on water
Suction nozzle
Mechanical seal
Gland packing
Casing
Sewabloc
Sewatec
[mm] [mm] [Nm/rad] [bar] [bar] [mm] [mm] [mm] [mm] [mm] [kgm2]
050-250 S01 - 65 50 13.000 - ✘ 10 15 - 80 25 200 150 0,027
050-250 - B01 65 50 13.000 - ✘ 10 15 - 80 25 200 150 0,027
050-251 S02 - 65 50 50.000 - ✘ 10 15 - 80 25 190 150 0,027
050-251 - B02 65 50 50.000 - ✘ 10 15 - 80 25 190 150 0,027
065-250 S01 - 80 65 13.000 - ✘ 6 9 - 80 65 210 170 0,027
065-250 - B01 80 65 13.000 - ✘ 6 9 - 80 65 210 170 0,027
080-250 S01 - 100 80 13.000 - ✘ 6 9 - 120 76 210/250 150 0,095
080-250 - B01 100 80 13.000 - ✘ 6 9 - 120 76 210/250 150 0,095
080-315 S03 - 100 80 80.000 - ✘ 10 15 - 120 76 250 150 0,119
080-315 S05 - 100 80 220.000 - ✘ 10 15 - 120 76 250 150 0,119
080-315 - B03 100 80 80.000 - ✘ 10 15 - 120 76 250 150 0,119
100-250 S01 - 100 100 50.000 - ✘ 6 9 118 120 100 210/265 170 0,119
100-250 - B01 100 100 50.000 - ✘ 6 9 118 120 100 210/265 170 0,119
100-251 S02 - 100 100 50.000 - ✘ 6 9 118 120 100 265 249 0,119
100-251 - B02 100 100 50.000 - ✘ 6 9 118 120 100 265 249 0,119
100-252 S01 - 100 100 50.000 - ✘ 6 9 118 120 100 210/265 170 0,119
100-252 - B01 100 100 50.000 - ✘ 6 9 118 120 100 210/265 170 0,119
100-253 S02 - 100 100 50.000 - ✘ 6 9 118 120 100 265 249 0,119
100-253 - B02 100 100 50.000 - ✘ 6 9 118 120 100 265 249 0,119
100-401 S04 - 125 100 190.000 - ✘ 10 15 120 120 100 390 325 0,475
100-401 S05 - 125 100 220.000 ■ ✘ 10 15 120 120 100 390 325 0,475
125-315 S03 - 125 125 80.000 - ✘ 6 9 118 120 120 300 240 0,214
125-315 - B03 125 125 80.000 - ✘ 6 9 118 120 120 300 240 0,214
150-315 S03 - 150 150 80.000 - ✘ 6 9 118 150 120 290 250 0,214
150-315 - B03 150 150 80.000 - ✘ 6 9 118 150 120 290 250 0,214
150-401 S04 - 150 150 190.000 - ✘ 10 15 120 200 135 390 325 0,475
150-401 S05 - 150 150 220.000 ■ ✘ 10 15 120 200 135 390 325 0,475
150-401 S06 - 150 150 370.000 ■ ✘ 10 15 120 200 135 390 325 0,475
Sewatec / Sewabloc 23
Waste Water
Dry-installed Volute Casing Pump
E impeller
Overview
Size Bearing Pump data E impeller
bracket Shaft seal Pressure limits Inspection
hole diameter
based on water
Suction nozzle
Mechanical seal
Gland packing
Casing
Sewabloc
Sewatec
[mm] [mm] [Nm/rad] [bar] [bar] [mm] [mm] [mm] [mm] [mm] [kgm2]
100-250 S01 - 100 100 50.000 - ✘ 6 9 118 120 100 245 - 0,16
100-250 - B01 100 100 50.000 - ✘ 6 9 118 120 100 245 - 0,16
100-251 S02 - 100 100 50.000 - ✘ 6 9 118 120 100 265 - 0,16
100-251 - B02 100 100 50.000 - ✘ 6 9 118 120 100 265 - 0,16
100-401 S04 - 125 100 190.000 - ✘ 10 15 120 120 80 412 389 0,65
100-401 S05 - 125 100 220.000 ■ ✘ 10 15 120 120 80 412 389 0,65
125-317 S03 - 125 125 80.000 - ✘ 6 9 118 120 100 330 - 0,25
125-317 - B03 125 125 80.000 - ✘ 6 9 118 120 100 330 - 0,25
150-315 S03 - 150 150 80.000 - ✘ 6 9 118 150 120 320 - 0,25
150-315 - B03 150 150 80.000 - ✘ 6 9 118 150 120 320 - 0,25
150-401 S05 - 150 150 220.000 ■ ✘ 10 15 120 200 135 407 348 0,68
150-401 S06 - 150 150 370.000 ■ ✘ 10 15 120 200 135 388 348 0,68
200-400 S04 - 200 200 190.000 - ✘ 10 15 200 200 125 400 319 0,86
200-400 S05 - 200 200 220.000 ■ ✘ 10 15 200 200 125 400 319 0,86
200-400 S06 - 200 200 370.000 ■ ✘ 10 15 145 200 125 400 319 0,86
200-500 S05 - 200 200 220.000 ■ ✘ 10 15 118 200 150 508 420 2,07
200-500Ex S05 - 200 200 220.000 ■ ✘ 10 15 200 200 200 500 500 3,47
250-500 S06 - 250 250 370.000 ■ ✘ 10 15 200 200 180 516 454 3,22
250-500 S07 - 250 250 1.020.000 ■ ✘ 10 15 200 200 180 516 454 3,22
250-630 S07 - 250 250 1.020.000 ■ ✘ 10 15 200 143 196 640 540 6,56
250-630 S08 - 250 250 1.400.000 ■ ✘ 10 15 200 143 196 640 540 6,56
300-630 S07 - 300 300 1.020.000 ■ ✘ 10 15 200 200 220 640 530 7,25
300-630 S08 - 300 300 1.400.000 ■ ✘ 10 15 200 200 220 640 530 7,25
350-710 S07 - 400 350 1.020.000 ■ ✘ 6 9 200 200 280 740 670 15,21
350-710 S08 - 400 350 1.400.000 ■ ✘ 6 9 200 200 280 740 670 15,21
24 Sewatec / Sewabloc
Waste Water
Dry-installed Volute Casing Pump
Motor ratings
Motor ratings, 50 Hz
Motor size Motor rating to IEC IP 55 [kW]42)
50 Hz
2900 rpm 450 rpm 960 rpm 750 rpm
100 L 3 2,2 1,5 0,75
3 1,1
112 M 4 4 2,2 1,5
132 S 5,5 5,5 3 2,2
7,5
132 M - 7,5 4 3
5,5
160 M 11 11 7,5 4
15 5,5
160 L 18,5 15 11 7,5
180 M 22 18,5 - -
180 L - 22 15 11
200 L 30 30 18,5 15
37 22
225 S - 37 - 18,5
225 M 45 45 30 22
250 M 55 55 37 30
280 S 75 75 45 37
280 M 90 90 55 45
315 S 110 110 75 55
315 M 132 132 90 75
315 L 160 160 110 90
200 200 132 110
250 250 160 132
315 315 200
315 - - 250 160
200
355 355 355 315 250
400 400 355 315
500 500 400
42) The motor ratings per motor size may differ, depending on the make.
Sewatec / Sewabloc 25
Waste Water
Dry-installed Volute Casing Pump
Motor ratings, 60 Hz
Motor size Motor rating42) to IEC IP 55 [kW]
1750 rpm 1160 rpm 875 rpm
100 L 2,55 1,75 1,3
3,45
112 M 4,55 2,55 1,75
132 S 6,3 3,45 2,55
132 M 8,6 4,6 3,45
6,3
160 M 12,6 8,6 4,6
6,3
160 L 17,3 12,6 8,6
180 M 18,5 - -
180 L 25,3 18 13,2
200 L 34,5 22 18
26,5
225 S 42,5 - 22
225 M 52 36 26,5
250 M 63 44,5 36
280 S 86 54 44,5
280 M 104 66 54
315 S 127 90 66
315 M 152 108 90
315 L 184 132 108
230 158 132
300 192 158
400 240
315 288 - -
362
355 408 - -
460
575
400 644 - -
725
42) The motor ratings per motor size may differ, depending on the make.
26 Sewatec / Sewabloc
Selection charts
20 30 40 50 US.gpm 100 200 300 400 500 1000 2000 3000 4000 5000
20 30 40 50 IM.gpm 100 200 300 400 500 1000 2000 3000 4000 5000
100
300
50
40 100-400K 200-631K
80-315K 100-401K
30 150-400K 100
200-400K
20 125-315K
100-251K
50
50-250K 80-250K 200-330K
40
10 150-315K
30
65-250K
200-315K 20
200-316K
5
100-250K
3 10
ft
2
H
5
[m]
Waste Water
4
1
1 Q[l/s] 2 3 4 5 10 20 30 40 50 100 200 300 400 500
400-820K /6p
200
350-710K /6p
50
250-630K /6p
40 400-710K /6p
250-400K /4p
250-401K /4p 400-630K /6p
20
50
300-500K /6p 350-500K /6p
40
400-500K /6p
10
30
250-400K /6p 300-400K /6p
250-401K /6p 300-401K /6p
350-500K /8p 20
4 400-500K /8p
H 300-400K /10p
[m] 300-401K /10p 5
Waste Water
40 50 Q[l/s] 100 200 300 400 500 1000 2000
200 300 400 500 m³/h 1000 2000 3000 4000 5000
Sewatec/Sewabloc, n = 960/725/580/480 rpm, K impeller, nominal discharge nozzle diameter 500, 600, 700 (diameter-based selection chart)
200
50
40
500-710K /6p
500-900K /8p 100
30
500-632K /6p
600-900K /8p
20
600-900K /10p
500-900K /10p
50
500-630K /6p 600-710K /8p
40
10 700-900K /10p
30
600-710K /10p
500-630K /8p
600-520K /8p 20
3 10
ft
2
H
5
[m]
Waste Water
200 300 400 500 Q[l/s] 1000 2000 3000
200 300 400 500 US.gpm 1000 2000 3000 4000 5000
200 300 400 500 IM.gpm 1000 2000 3000 4000 5000
100
300
200
50
40
50
80-316D
100-316D 150-315D 200-400D 40
10 250-400D
30
200-315D 300-400D 20
100-251D 150-251D
5
ft
2
H
5
[m]
4
Waste Water
9 10 Q[l/s] 20 30 40 50 100 200 300 400 500
200
50 100-401F 80-315F
40
50-251F
30 100
50
40
65-250F 100-250F 100-253F
10
30
20
100-252F 150-315F
5
ft
2
H
5
[m]
4
Waste Water
1 Q[l/s] 2 3 4 5 10 20 30 40 50 100 200
100 US.gpm 200 300 400 500 1000 2000 3000 4000 5000 10000
100 IM.gpm 200 300 400 500 1000 2000 3000 4000 5000 10000
50
40
150-401E
30 100
100-401E 250-630E
40
10
100-250E 150-315E 200-500E 30
20
3 10
H
5
[m]
Waste Water
6 10 Q[l/s] 20 30 40 50 100 200 300 400 500 800
1 l/s 2 3 4 5 10 20 30 40 50 100
400
100
300
200
50
40
100-401K /6p 20
50
50-251K /4p
40 80-315K /4p 100-251K /4p
10
30
20
50-250K /6p 65-250K /6p 5
10 3
H 50-250K /8p 65-250K /8p 100-251K /6p
5 m
4
1
3
Waste Water
10 Q[US.gpm] 20 30 40 50 100 200 300 400 500 1000 2000
200
150-401K /4p 200-631K /6p 50
40
100 30
200-631K /8p
150-315K/ 4p 150-400K /6p 20
200-501K /6p
50
150-401K /6p
40 200-400K /6p
200-402K /6p 10
30
150-315K /6p 200-330K /6p
20
200-315K /6p 5
4
150-315K /8p
10 3
H 200-316K /6p
5 200-330K /8p
200-316K /8p m
4
1
3
Waste Water
200 300 400 500 Q[US.gpm] 1000 2000 3000 4000 5000 7000
200 300 400 500 IM.gpm 1000 2000 3000 4000 5000
Sewatec/Sewabloc, n = 1160/875/700 rpm, impeller K, discharge nozzle diameter DN 250, 300 (diameter selection chart)
100
300
250-900K /8p
250-630K/ 6p
200
50
40
250-630K /8p
100 30
20
50
40
250-400K /6p
10
30 300-400K /6p
300-401K /6p
m
250-400K /8p 250-401K /6p
20
10 3
H
[ft] 300-400K /10p
300-401K /10p 2
Waste Water
700 1000 Q[US.gpm] 2000 3000 4000 5000 9000
300 400 500 m³/h 1000 2000 3000 4000 5000 10000
100
300
50
350-710K /8p
500-900K /10p 40
350-500K /8p
50
600-710K /10p
40 350-501K /8p
600-710K /12p
10
30 350-500K /10p
700-900K /12p
350-501K /10p 400-500K /8p 500-630K /8p m
20
600-520K /10p
5
700-900K /14p
4
Waste Water
1000 Q[US.gpm] 2000 3000 4000 5000 10000 20000 30000 40000 50000
1000 IM.gpm 2000 3000 4000 5000 10000 20000 30000 40000
Sewatec/Sewabloc, n = 1750/1160/875 rpm, impeller D (diameter selection chart)
40
100 30
150-401D /6p 20
80-315D /4p
50
40 150-400D /6p
10
30 100-316D /6p
200-400D /6p 300-400D /6p
250-400D /6p 4
H
[ft]
150-251D /6p 250-400D /8p 2
200-315D /8p m
1
3
Waste Water
100 Q[US.gpm] 200 300 400 500 1000 2000 3000 4000 5000 6000
100 IM.gpm 200 300 400 500 1000 2000 3000 4000
37
Sewatec/Sewabloc, n = 1750/1160/875 rpm, impeller F (diameter selection chart)
38
Sewatec / Sewabloc
4 5 l/s 10 20 30 40 50 100
160
40
125-315F /4p
100 30
100-251F /4p
80-315F /4p
20
50
40
50-250F /4p 100-253F /4p 150-401F /6p 10
30
20
1
3
Waste Water
50 Q[US.gpm] 100 200 300 400 500 1000 2000 3000
30 40 50 m³/h 100 200 300 400 500 1000 2000 3000 4000
40
100 30
300-630E /8p 20
250-500E /8p
50
350-710E /10p
40 125-317E /6p
300-630E /10p 10
30
250-500E /10p 350-710E /12p
125-317E /8p
20
100-251E /6p
100-250E /6p 150-315E /6p 5
125-317E /10p
4
1
3
Waste Water
100 Q[US.gpm] 200 300 400 500 1000 2000 3000 4000 5000 10000 20000
100 IM.gpm 200 300 400 500 1000 2000 3000 4000 5000 10000
39
Waste Water
Dry-installed Volute Casing Pump
Types of installation
Horizontal installation
Sewatec - Fig. 0 Sewabloc
Bare shaft pump Pump set with directly flanged motor (B5/V1 type of
construction)
Pump set with baseplate, belt drive and belt guard Pump set with baseplate, belt drive, belt guard and motor stand
Pump set with baseplate, coupling (also with coupling spacer), Pump set with directly coupled drive, baseplate, coupling (also
coupling guard, counter shaft stand, counter shaft, motor stand, with coupling spacer), coupling guard and height adjustment of
belt drive and belt guard the motor
Vertical installation
Sewatec – vertical (V) Sewatec – vertical (VU)
Bare shaft pump, soleplate and suction elbow Pump set with soleplate, drive lantern, coupling, coupling guard
and suction elbow
40 Sewatec / Sewabloc
Waste Water
Dry-installed Volute Casing Pump
Pump set with soleplate for pump and motor, supporting frame, Pump set with directly flanged motor (B5/V1 type of
drive lantern, suction elbow and universal joint shaft construction), with soleplate and suction elbow, for underfloor
installation
Sewatec / Sewabloc 41
Waste Water
Dry-installed Volute Casing Pump
Impeller type
BLOC BLOC-V BLOC-VF Fig.0 3EN 3ENH 3HZ 3HM 3HVG-N 3HVG-NH V VU VGW
050-250 B01 F ✘ ✘ ✘ - - - - - - - - - -
050-250 B01 K ✘ ✘ ✘ - - - - - - - - - -
050-250 S01 F - - - ✘ ✘ ✘ ✘ - - - ✘ - -
050-250 S01 K - - - ✘ ✘ ✘ ✘ - - - ✘ - -
050-251 B02 F ✘ ✘ ✘ - - - - - - - - - -
050-251 B02 K ✘ ✘ ✘ - - - - - - - - - -
050-251 S02 F - - - ✘ ✘ ✘ ✘ - - - ✘ - -
050-251 S02 K - - - ✘ ✘ ✘ ✘ - - - ✘ - -
065-250 B01 F ✘ ✘ ✘ - - - - - - - - - -
065-250 B01 K ✘ ✘ ✘ - - - - - - - - - -
065-250 S01 F - - - ✘ ✘ ✘ ✘ - - - ✘ - -
065-250 S01 K - - - ✘ ✘ ✘ ✘ - - - ✘ - -
080-250 B01 F ✘ ✘ ✘ - - - - - - - - - -
080-250 B01 K ✘ ✘ ✘ - - - - - - - - - -
080-250 S01 F - - - ✘ ✘ ✘ ✘ - - - ✘ - -
080-250 S01 K - - - ✘ ✘ ✘ ✘ - - - ✘ - -
080-315 B03 D ✘ ✘ ✘ - - - - - - - - - -
080-315 B03 F ✘ ✘ ✘ - - - - - - - - - -
080-315 B03 K ✘ ✘ ✘ - - - - - - - - - -
080-315 S03 D - - - ✘ ✘ ✘ ✘ - - - ✘ - -
080-315 S03 F - - - ✘ ✘ ✘ ✘ - - - ✘ - -
080-315 S03 K - - - ✘ ✘ ✘ ✘ - - - ✘ - -
080-315 S05 D - - - ✘ ✘ ✘ ✘ ✘ - - - - -
080-316 B03 D ✘ ✘ ✘ - - - - - - - - - -
080-316 S03 D - - - ✘ ✘ ✘ ✘ - - - ✘ - -
100-250 B01 E - - - - - - - - - - - - -
100-250 B01 F ✘ ✘ ✘ - - - - - - - - - -
100-250 B01 K ✘ ✘ ✘ - - - - - - - - - -
100-250 S01 E - - - ✘ ✘ ✘ ✘ - - - ✘ - -
100-250 S01 F - - - ✘ ✘ ✘ ✘ - - - ✘ - -
100-250 S01 K - - - ✘ ✘ ✘ ✘ - - - ✘ - -
100-251 B02 D ✘ ✘ ✘ - - - - - - - - - -
100-251 B02 E - - - - - - - - - - - - -
100-251 B02 F ✘ ✘ ✘ - - - - - - - - - -
100-251 B02 K ✘ ✘ ✘ - - - - - - - - - -
100-251 S02 D - - - ✘ ✘ ✘ ✘ - - - ✘ - -
100-251 S02 E - - - ✘ ✘ ✘ ✘ - - - ✘ - -
100-251 S02 F - - - ✘ ✘ ✘ ✘ - - - ✘ - -
100-251 S02 K - - - ✘ ✘ ✘ ✘ - - - ✘ - -
100-252 B01 F ✘ ✘ ✘ - - - - - - - - - -
100-252 S01 F - - - ✘ ✘ ✘ ✘ - - - ✘ - -
100-253 B02 F ✘ ✘ ✘ - - - - - - - - - -
100-253 S02 F - - - ✘ ✘ ✘ ✘ - - - ✘ - -
100-315 B03 D ✘ ✘ ✘ - - - - - - - - - -
100-315 S03 D - - - - - - - - - - ✘ - -
100-315 S05 D - - - ✘ ✘ ✘ ✘ - - - - - -
100-316 B03 D ✘ ✘ ✘ - - - - - - - - - -
100-316 S03 D - - - ✘ ✘ ✘ ✘ - - - ✘ - -
100-400 S04 K - - - ✘ ✘ ✘ ✘ ✘ - - ✘ - -
100-400 S05 K - - - ✘ ✘ ✘ ✘ ✘ - - ✘ ✘ ✘
100-401 S04 E - - - ✘ ✘ ✘ ✘ - - - - - -
100-401 S04 F - - - ✘ ✘ ✘ ✘ - - - - - -
100-401 S04 K - - - ✘ ✘ ✘ ✘ - - - - - -
100-401 S05 E - - - ✘ ✘ ✘ ✘ ✘ - - ✘ ✘ ✘
100-401 S05 F - - - ✘ ✘ ✘ ✘ ✘ - - ✘ ✘ ✘
100-401 S05 K - - - ✘ ✘ ✘ ✘ ✘ - - ✘ ✘ ✘
125-315 B03 F ✘ ✘ ✘ - - - - - - - - - -
125-315 B03 K ✘ ✘ ✘ - - - - - - - - - -
125-315 S03 F - - - ✘ ✘ ✘ ✘ - - - ✘ - -
125-315 S03 K - - - ✘ ✘ ✘ ✘ - - - ✘ - -
125-317 B03 E - - - - - - - - - - - - -
125-317 S03 E - - - ✘ ✘ ✘ ✘ - - - ✘ - -
150-251 B02 D ✘ ✘ ✘ - - - - - - - - - -
150-251 S02 D - - - ✘ ✘ ✘ ✘ - - - ✘ - -
150-315 B03 D ✘ ✘ ✘ - - - - - - - - - -
150-315 B03 E - - - - - - - - - - - - -
150-315 B03 F ✘ ✘ ✘ - - - - - - - - - -
150-315 B03 K ✘ ✘ ✘ - - - - - - - - - -
150-315 S03 D - - - ✘ ✘ ✘ ✘ - - - ✘ - -
150-315 S03 E - - - ✘ ✘ ✘ ✘ - - - ✘ - -
150-315 S03 F - - - ✘ ✘ ✘ ✘ - - - ✘ - -
150-315 S03 K - - - ✘ ✘ ✘ ✘ - - - ✘ - -
150-400 S04 K - - - ✘ ✘ ✘ ✘ ✘ - - ✘ - -
42 Sewatec / Sewabloc
Waste Water
Dry-installed Volute Casing Pump
Bearing bracket
Impeller type
BLOC BLOC-V BLOC-VF Fig.0 3EN 3ENH 3HZ 3HM 3HVG-N 3HVG-NH V VU VGW
150-400 S05 D - - - ✘ ✘ ✘ ✘ ✘ - - ✘ ✘ ✘
150-400 S05 K - - - ✘ ✘ ✘ ✘ ✘ - - ✘ ✘ ✘
150-401 S04 E - - - ✘ ✘ ✘ ✘ - - - ✘ - -
150-401 S04 F - - - ✘ ✘ ✘ ✘ - - - ✘ - -
150-401 S04 K - - - ✘ ✘ ✘ ✘ - - - ✘ - -
150-401 S05 D - - - ✘ ✘ ✘ ✘ ✘ - - ✘ ✘ ✘
150-401 S05 E - - - ✘ ✘ ✘ ✘ ✘ - - ✘ ✘ ✘
150-401 S05 F - - - ✘ ✘ ✘ ✘ ✘ - - ✘ ✘ ✘
150-401 S05 K - - - ✘ ✘ ✘ ✘ ✘ - - ✘ ✘ ✘
150-401 S06 D - - - ✘ ✘ ✘ - - - - ✘ ✘ ✘
150-401 S06 E - - - ✘ ✘ ✘ - ✘ - - ✘ ✘ ✘
150-500 S05 K - - - ✘ ✘ ✘ ✘ ✘ ✘ ✘ ✘ ✘ ✘
150-500 S06 K - - - ✘ - - - - - - ✘ ✘ -
151-401 S05 K - - - ✘ - - - - - - ✘ ✘ -
200-315 B03 D ✘ ✘ ✘ - - - - - - - - - -
200-315 B03 K ✘ ✘ ✘ - - - - - - - - - -
200-315 S03 D - - - ✘ ✘ ✘ ✘ - - - ✘ - -
200-315 S03 K - - - ✘ ✘ ✘ ✘ - - - ✘ - -
200-316 B03 K ✘ ✘ ✘ - - - - - - - - - -
200-316 S03 K - - - ✘ ✘ ✘ ✘ - - - ✘ - -
200-330 S04 K - - - ✘ ✘ ✘ ✘ - - - - - -
200-330 S05 K - - - ✘ ✘ ✘ ✘ ✘ - - ✘ ✘ ✘
200-400 S04 E - - - ✘ ✘ ✘ ✘ - - - - - -
200-400 S04 K - - - ✘ ✘ ✘ ✘ - - - - - -
200-400 S05 D - - - ✘ ✘ ✘ ✘ ✘ - - ✘ ✘ ✘
200-400 S05 E - - - ✘ ✘ ✘ ✘ ✘ - - ✘ ✘ ✘
200-400 S05 K - - - ✘ ✘ ✘ ✘ ✘ - - ✘ ✘ ✘
200-400 S06 D - - - ✘ ✘ ✘ - ✘ - - ✘ ✘ ✘
200-400 S06 E - - - ✘ ✘ ✘ - ✘ - - ✘ ✘ ✘
200-402 S04 K - - - ✘ ✘ ✘ ✘ ✘ - - ✘ - -
200-402 S05 K - - - ✘ ✘ ✘ ✘ ✘ - - ✘ ✘ ✘
200-500 S05 E - - - ✘ ✘ ✘ ✘ ✘ - - ✘ ✘ ✘
200-500 S06 K - - - ✘ ✘ ✘ - - - - ✘ ✘ ✘
200-500 S07 K - - - ✘ ✘ ✘ - ✘ ✘ ✘ ✘ ✘ ✘
200-501 S06 K - - - ✘ - - - - - - ✘ ✘ -
200-631 S07 K - - - ✘ - - - - - - ✘ ✘ -
200-631 S08 K - - - ✘ - - - - - - ✘ ✘ -
250-400 S04 K - - - ✘ ✘ ✘ ✘ - - - - - -
250-400 S05 D - - - ✘ ✘ ✘ ✘ ✘ - - ✘ ✘ ✘
250-400 S05 K - - - ✘ ✘ ✘ ✘ ✘ - - ✘ ✘ ✘
250-400 S06 D - - - ✘ ✘ ✘ - ✘ - - ✘ ✘ ✘
250-401 S04 K - - - ✘ ✘ ✘ ✘ - - - - - -
250-401 S05 K - - - ✘ ✘ ✘ ✘ ✘ - - ✘ ✘ ✘
250-500 S06 E - - - ✘ ✘ ✘ - ✘ - - ✘ ✘ ✘
250-500 S07 E - - - ✘ ✘ ✘ - ✘ - - ✘ ✘ ✘
250-630 S07 E - - - ✘ ✘ ✘ - ✘ - - ✘ ✘ ✘
250-630 S07 K - - - ✘ ✘ ✘ - ✘ ✘ ✘ ✘ ✘ ✘
250-630 S08 E - - - ✘ ✘ ✘ - - ✘ ✘ ✘ ✘ ✘
250-630 S08 K - - - ✘ - - - - - - ✘ ✘ ✘
250-900 S09 K - - - - - - - - - - ✘ - -
300-400 S04 K - - - ✘ ✘ ✘ ✘ - - - - - -
300-400 S05 D - - - ✘ ✘ ✘ ✘ ✘ - - ✘ ✘ ✘
300-400 S05 K - - - ✘ ✘ ✘ ✘ ✘ - - ✘ ✘ ✘
300-400 S06 D - - - ✘ ✘ ✘ - ✘ - - ✘ ✘ ✘
300-401 S04 K - - - ✘ ✘ ✘ ✘ - - - - - -
300-401 S05 K - - - ✘ ✘ ✘ ✘ ✘ - - ✘ ✘ ✘
300-500 S06 K - - - ✘ ✘ ✘ - ✘ - - ✘ ✘ ✘
300-500 S07 K - - - ✘ ✘ ✘ - - ✘ ✘ ✘ ✘ ✘
300-630 S07 E - - - ✘ ✘ ✘ - ✘ - - ✘ ✘ ✘
300-630 S08 E - - - ✘ ✘ ✘ - - ✘ ✘ ✘ ✘ ✘
350-500 S06 K - - - ✘ ✘ ✘ - ✘ - - ✘ ✘ ✘
350-500 S07 K - - - ✘ ✘ ✘ - ✘ ✘ ✘ ✘ ✘ ✘
350-501 S06 K - - - ✘ ✘ ✘ - ✘ - - ✘ ✘ ✘
350-501 S07 K - - - ✘ ✘ ✘ - - ✘ ✘ ✘ ✘ ✘
350-630 S07 K - - - ✘ ✘ ✘ - ✘ ✘ ✘ ✘ ✘ ✘
350-630 S08 K - - - ✘ ✘ ✘ - - - - ✘ ✘ ✘
350-710 S07 E - - - ✘ - - - - - - ✘ ✘ ✘
350-710 S08 E - - - ✘ ✘ ✘ - - ✘ ✘ ✘ ✘ ✘
350-710 S08 K - - - ✘ - - - - - - ✘ ✘ -
400-500 S06 K - - - ✘ - - - - - - ✘ ✘ -
400-500 S07 K - - - ✘ - - - - - - ✘ ✘ -
400-630 S08 K - - - ✘ - - - - - - ✘ ✘ -
400-710 S09 K - - - - - - - - - - ✘ - -
400-820 S09 K - - - - - - - - - - ✘ - -
500-630 S07 K - - - ✘ ✘ ✘ - ✘ ✘ ✘ ✘ ✘ ✘
500-630 S08 K - - - ✘ - - - - - - ✘ ✘ ✘
Sewatec / Sewabloc 43
Waste Water
Dry-installed Volute Casing Pump
Bearing bracket
Impeller type
BLOC BLOC-V BLOC-VF Fig.0 3EN 3ENH 3HZ 3HM 3HVG-N 3HVG-NH V VU VGW
500-632 S08 K - - - ✘ ✘ ✘ - - ✘ ✘ ✘ ✘ ✘
500-710 S09 K - - - - - - - - - - ✘ - -
500-900 S09 K - - - - - - - - - - ✘ - -
500-900 S10 K - - - - - - - - - - ✘ - -
600-520 S07 K - - - ✘ - - - - - - ✘ ✘ -
600-710 S08 K - - - ✘ - - - - - - ✘ - -
600-900 S10 K - - - - - - - - - - ✘ - -
700-900 S08 K - - - ✘ - - - - - - ✘ - -
44 Sewatec / Sewabloc
Waste Water
Dry-installed Volute Casing Pump
Replacement part
(including stand-by pumps)
1 2 3 4 5 6 8 10 and more
Spare part
Wear part
163 Discharge cover 1 2 2 2 3 3 4 50 % ✘ - -
210 Shaft 1 1 1 2 2 2 3 30 % ✘ - -
230 Impeller 1 1 1 2 2 2 3 30 % - ✘ -
321.01/02 Rolling element bearing (set) 1 1 1 2 2 3 4 50 % - - ✘
330 Bearing bracket, complete - - - - - - 1 2 pcs. ✘ - -
433.01/02 Mechanical seal, complete (set) 1 2 3 4 4 4 6 90 % - - ✘
Assembly for gland packing 1 1 1 2 2 2 3 40 % - ✘ -
consisting of:
▪ Neck bush
▪ Shaft protecting sleeve
▪ Lantern ring
Packing cord (4 rings) 4 4 6 8 8 9 12 100 % - - ✘
502.01 Casing wear ring 1 2 2 2 3 3 4 50 % - - ✘
503 Impeller ring 1 2 2 2 3 3 4 50 % - - ✘
135 Wear plate 1 2 2 2 3 3 4 50 % - - ✘
Sealing elements (set) 2 4 6 8 8 9 12 150 % - - ✘
Sewatec
Scope of supply Depending on the model, the following items are included in
the scope of supply:
Sewabloc
▪ Pump
Depending on the model, the following items are included in
the scope of supply: ▪ Drive
▪ Pump without motor or with directly flanged standardised ▪ Baseplate or soleplate
motor
▪ Coupling and coupling guard
▪ Foundation rails43) ▪ Suction-side double-flanged taper or suction elbow with
▪ Suction-side double-flanged taper or suction elbow with inspection hole
inspection hole ▪ Universal joint shaft
▪ Baseplate or soleplate
Sewatec / Sewabloc 45
Waste Water
Dry-installed Volute Casing Pump
General assembly drawing: Sewatec with bearing brackets S01, S02, S03, S04
411.02 903.02
903.03
902.01
920.01 903.90 411.90 321.01 330 321.02
411.03
101
932.02
502
914.10 /
906
550.23*
904.01** 940.02
433.02 360.02
230
901.01
903.01
550.01
411.01
163 515 /
932.03 932.20 411.22 183
412.04
412.15 411.46 903.46 433.01 903.22 210
Sewatec with E impeller
Impeller types
230 914.12
230 412.34
230
914.10
550.23
914.24
135
F impeller K impeller D impeller
46 Sewatec / Sewabloc
Waste Water
Dry-installed Volute Casing Pump
900.02
503
920.17 914.10
550.04 260
164.02 940.01
412.05
Inspection hole Option: impeller wear ring (K impeller) Impeller fastening for bearing bracket S04
List of components
Part No. Description Part No. Description
101 Pump casing 502 Casing wear ring
135 Wear plate 503 Impeller wear ring45)
163 Discharge cover 504 Spacer ring
164 Inspection cover 515 Taper lock ring
183 Support foot 550 Disc
210 Shaft 900 Screw
230 Impeller 901 Hexagon head bolt
260 Impeller hub cap 902 Stud
321 Deep groove ball bearing 903 Screw plug
330 Bearing bracket 906 Impeller screw
360 Bearing cover 914 Hexagon socket head cap screw
411 Joint ring 920 Nut
412 O-ring 932 Circlip
433 Mechanical seal 940 Key
Sewatec / Sewabloc 47
Waste Water
Dry-installed Volute Casing Pump
General assembly drawing: Sewatec with bearing brackets S05, S06, S07, S08
Horizontal installation
903.07
903.03 411.07
902.01 903.90
411.03 412.35 920.01 412.11 411.90 636.02 412.02 914.18 320.02 636.03
101
931.01
502
920.21
230
421.02
412.06
433.02 433.01 940.02
906
210
525.04
500.32
412.03
330.12
550.23
940.01 932.02
411.01 183
Impeller types
X
502* 914.12
412.34
230
13-6** 914.10
550.23
914.24
135
F impeller K impeller D impeller
(* Not for 100-401.
** For 100-401, 200-400 only.)
48 Sewatec / Sewabloc
Waste Water
Dry-installed Volute Casing Pump
X 260.01
900.02
550.87
920.17 503
901.87
550.04 931.02
164.02 412.03
412.04
Inspection hole Option: impeller wear Impeller fastening for bearing brackets S06 and
ring (K impeller) larger,
except pump size 500-632
List of components
Part No. Description Part No. Description
13-6 Casing insert 502 Casing wear ring
101 Pump casing 503 Impeller wear ring46)
135 Wear plate 504 Spacer ring
163 Discharge cover 525 Spacer sleeve
164 Inspection cover 550 Disc
183 Support foot 636 Lubricating nipple
210 Shaft 900 Screw
230 Impeller 901 Hexagon head bolt
320 Rolling element bearing 902 Stud
322 Radial roller bearing 903 Screw plug
330 Bearing bracket 906 Impeller screw
411 Joint ring 914 Hexagon socket head cap screw
412 O-ring 920 Nut
421 Lip seal 931 Lock washer
432 Auxiliary seal 932 Circlip
433 Mechanical seal 940 Key
500 Ring
Sewatec / Sewabloc 49
Waste Water
Dry-installed Volute Casing Pump
500.32
914.24
550.23 550.24
932.02 421.02
500.31 330.12
914.18
932.01
421.01
322.01
330.11
412.02
433.01
636.02
504.52
903.90
411.90 932.03
412.24 903.46
411.46
902.01
920.01 903.22
411.22
903.02
411.02
412.11
903.07
411.07 412.35
163
433.02
940.01 525.04
101 412.06
502 230
412.03
400.03
906
901.01
550.07 903.01
411.01
164.01 901.16
550.16
Sewatec with E impeller – pump for underfloor installation, shaft sealed by mechanical seal
* If applicable
Impeller types
X
502* 914.12
412.34
230
13-6** 914.10
550.23
914.24
135
F impeller K impeller D impeller
(* Not for 100-401.
** For 100-401, 200-400 only.)
50 Sewatec / Sewabloc
Waste Water
Dry-installed Volute Casing Pump
X 260.01
900.02
550.87
920.17 503
901.87
550.04 931.02
164.02 412.03
412.04
Inspection hole Option: impeller wear Impeller fastening for bearing brackets S06 and
ring (K impeller) larger,
except pump size 500-632
List of components
Part No. Description Part No. Description
101 Pump casing 504 Spacer ring
139 Suction elbow 525 Spacer sleeve
163 Discharge cover 550 Disc
164 Inspection cover 576 Handle
210 Shaft 636 Lubricating nipple
230 Impeller 680 Guard
322 Radial roller bearing 893 Soleplate
320 Rolling element bearing 900 Bolt/screw
330 Bearing bracket 901 Hexagon head bolt
341 Drive lantern 902 Stud
400 Gasket 903 Screw plug
411 Joint ring 906 Impeller screw
412 O-ring 914 Hexagon socket head cap screw
421 Lip seal 920 Nut
433 Mechanical seal 931 Lock washer
500 Ring 932 Circlip
502 Casing wear ring 940 Key
503 Impeller wear ring47)
Sewatec / Sewabloc 51
Waste Water
Dry-installed Volute Casing Pump
500.32
550.23
421.02
932.02
500.31 330.12
914.18
932.01
421.01
322.01
330.11
412.02
433.01
636.02
504.52
903.90
411.90 932.03
412.24 903.46
411.46
902.01
920.01 903.22
411.22
903.02
411.02
412.11
903.07
411.07
412.35
163
433.02
940.01 525.04
101 412.06
502 230
400.03 412.03
906
901.01
550.07 903.01
411.01
164.01
901.16
550.16
Sewatec with E impeller – pump with universal joint shaft, shaft sealed by mechanical seal
* If applicable
52 Sewatec / Sewabloc
Waste Water
Dry-installed Volute Casing Pump
Impeller types
X
502* 914.12
412.34
230
13-6** 914.10
550.23
914.24
135
F impeller K impeller D impeller
(* Not for 100-401.
** For 100-401, 200-400 only.)
X 260.01
900.02
550.87
920.17 503
901.87
550.04 931.02
164.02 412.03
412.04
Inspection hole Option: impeller wear Impeller fastening for bearing brackets S06 and
ring (K impeller) larger,
except pump size 500-632
List of components
Part No. Description Part No. Description
101 Pump casing 504 Spacer ring
139 Suction elbow 525 Spacer sleeve
163 Discharge cover 550 Disc
164 Inspection cover 576 Handle
210 Shaft 636 Lubricating nipple
230 Impeller 680 Guard
320 Rolling element bearing 893 Soleplate
322 Radial roller bearing 900 Bolt/screw
330 Bearing bracket 901 Hexagon head bolt
341 Drive lantern 902 Stud
400 Gasket 903 Screw plug
411 Joint ring 906 Impeller screw
412 O-ring 914 Hexagon socket head cap screw
421 Lip seal 920 Nut
433 Mechanical seal 931 Lock washer
500 Ring 932 Circlip
502 Casing wear ring 940 Key
503 Impeller wear ring48)
Sewatec / Sewabloc 53
Waste Water
Dry-installed Volute Casing Pump
411.03
101
433.01
502 433.02
914.10 /
906
550.23*
515 /
904.01**
932.03
230 932.20
800
901.57
920.57
903.01 411.01 163 412.15 412.04 903.46 411.46 903.22 411.22 550.57
901.99
Sewabloc with F impeller
Impeller types
914.24 412.05
135
K impeller D impeller Inspection hole
503
List of components
Part No. Description Part No. Description
101 Pump casing 503 Impeller wear ring49)
135 Wear plate 515 Taper lock ring
163 Discharge cover 550 Disc
164 Inspection cover 800 Motor
54 Sewatec / Sewabloc
Waste Water
Dry-installed Volute Casing Pump
Sewatec / Sewabloc 55
01.12.2014
2580.5/18-EN
KSB Aktiengesellschaft
P.O. Box 200743 • 06008 Halle (Saale) • Turmstraße 92 • 06110 Halle (Germany)
Tel. +49 345 4826-0 • Fax +49 345 4826-4699
www.ksb.com