Professional Documents
Culture Documents
Is 2582 3 1987 PDF
Is 2582 3 1987 PDF
/-
\.-_‘I/ Indian Standard
I
(Second Revision)
UDC 621.941:621.9-229.3:006.015.3
/-
\ ,’ ‘I
I
-._
0 BIS 1990
‘-\
:
\ -
I
BUREAU OF INDIAN STANDARDS
MANAK BHAVAN, 9 BAHADUR SHAH ZAFAR MARG
NEW DELHI 110002
Indian Standard
MACHINE TOOLS -SPINDLE NOSES AND FACE
PLATES- SIZES FOR INTERCHANGEABILITY
PART 3 BAYONET TYPE
(Second Revistonj
NATIONAL FOREWORD
This Indian Standard (Part 3) (Second Revision), which is identical with IS0 702/3 : 1975 ‘Machine
tools -Spindle noses, and face plates -Sizesfor interchangeability -Part3: Bayonettype’, issued by
the International Organization for Standardization (ISO) was adopted by the Bureau of Indian
Standards on 23 November 1987 on the recommendation of the Machine Tools, Machine Tool
Elements and Wood-Working Machines Sectional Committee (EDC 11) and approval of the
Mechanical Engineering Division Council.
This standard was first issued in 1963. After the formulation of ISO/R 702, this standard was revised
and split into three Darts in 1972. The IS0 recommendations have since been replaced by IS0 702/l,
IS0 70212 and IS0 702/3. With a viewto achieving international dimensions which are basic in
nature. this revision of IS 2582 (Part 3) and adoption of IS0 702/3:1975 has been considered.
The text of the IS0 standard has been approved as suitablefor publication as Indian Standard without
deviations. Certain conventions are, however, not identical to those used in Indian Standards.
Attention is particularly drawn to the following :
a) Wherever the words ‘International Standard’ appear referring to this standard, they should
be read as ‘Indian Standard’.
b) Comma (,) has been used as decimal marker while in Indian Standards, the current practice
is to use a point 1.1as the de,cimal marker.
ADDITIONAL INFORMATION
Spindle noses of TypeA and Camlock type are covered in Parts 1 and 2 of this standard, as follows :
IS 2582 (Part 1) : 19871180 702/l : 1975 Machine tools -Spindle noses and face plates -
Size for Interchangeability: Part 1 Type A
IS 2582 (Part 2) : 19871180 702/2 : 1975 Machine tools -Spindle noses and face plates -
Size for interchangeability: Part 2 Camlock type
As in the Original Standard, this Page is Intentionally Left Blank
IS 2582 (Part 3) : 1987
IS0 702/3 : 1975
This International Standard specifies the sizes for interchangeability of bayonet-type lathe spindle noses and corresponding
face plates.
NOTE - The types “A” and “Camlock” are dealt with in parts I and I I respectively
3
IS 2582 (Part 3):1987
ISO702/3:1975
Nos. 11 to20
Nor 3rnd4 Nos. 5 to 0
Taper 1 : 4
IS 2582 (Part 3) : 1987
IS0 702/3 : 1975
Dimensions in millimetres
dl 8
H8lh 14.25 15.9 19.05 23.8 28.6 34.9 %I,3
rf, 64 6.4
~.
6.4 8.4 10.5 10.5 13 13
1
-L -r
I I I I 1 I I
rl-
“;I
I lnA
.“,_
1 It-IA
._, .
1 1llA
__,_ II 13.5 tI 16.5 1 16.5 II 19 II 19
I --I- 1 I
E 11 11 13 14 16 18 19 21
F 16 20 22 25 28 35 42 48
.G 5 5 5 6 6 8 8
H 10 10 10 11 12 13 15 15
5
IS 25’82 (Part 3) : 1987
IS0 70213 : 1975
SectionA-A
Thrust socket
6
IS 2582 (Part 3) : 1987
IS0 702/3 : 1975
Dimensions in millimetres
s 14 14 14 17 22 22 27 27
7
IS 2582 (Part 3)’ : 1987
IS0 70213 : 1975
-t-
8
IS 2582 (Part 3) : 1987
IS0 702/3 : 1975
Dimensions in millimetre .
9
IS 2582 (Part 3) : 1987
IS0 702/3 : 1975
Stud
Dimensions in millimetres
dl
hll
Bmreao of Indian Standards
BIS is a statutory institution established under the Bureau of Indian Standards Act, 1986 to promote
harmonious development of the activities of standardization, marking and quality certification of goods
and attending to connected matters in the country.
Copyright
BIS has the copyrght of all its publications. No part of these publications may be reproduced in any form
without the prior permission in writing of BIS. This .does not preclude the free use, in the course of
implementing the standard, of necessary details, such as symbols and sizes, type or grade designations.
Enquiries relating to copyright be adressed to the Director ( Publications ), BIS.
Indian Standards are reviewed periodically and revised, when necessary and amendments, if any, are
issued from time to time. Users of Indian Standards should ascertain that they are in possession of the’
latest amendments or edition. Comments on this Indian Standard may be sent to BIS giving the
following reference:
Headquarters :
Manak Bhavan, 9 Bahadur Shah Zafar Marg, New Delhi 110002 Telegrams : Manaksanstha
Telephones : 331 01 31,331 13 75 ( Common to all 05ces )