Professional Documents
Culture Documents
Me Questions
Me Questions
On the basis of Indian standards fits can mainly be categorized into three groups:
> Clearance Fit: These types of fits are characterized by the occurrence of a clearance between the two
mating parts. The difference between the minimum size of the hole and the maximum size of the shaft is
called the minimum clearance, the difference between the maximum size of the hole and the minimum
size of the shaft is known as maximum clearance.
> Interference Fit: In these types of fits the size of the mating parts are predefined so that interference
between them always occurs. The tolerance zone of the hole is completely below the tolerance zone of
the shaft.
> Transition Fit: As the name suggests these type of fit has its mating parts sized limited to allow either
clearance or interference. The tolerance zone of the hole and the shaft overlaps in case of such fits.
What are the factors that can affect the Factor of safety selection?
The factor of safety is used in designing a machine component. Prior to selecting the correct factor of
safety certain points must be taken into consideration such as:
> The properties of the material used for the machine and the changes in its intrinsic properties over the
time period of service.
> The accuracy and authenticity of test results to the actual machine parts.
> The applied load reliability.
> The limit of stresses (localized).
> The loss of property and life in case of failures.
> The limit of initial stresses at the time period of manufacture.
> The extent to which the assumptions can be simplified.
The factor of safety also depends on numerous other considerations such as the material, the method of
manufacturing , the various types of stress, the part shapes etc.
What are the rules that must be kept in mind while designing castings?
Some of the points that must be kept in mind during the process of cast designing are as follows:
> To avoid the concentration of stresses sharp corners and frequent use of fillets should be avoided.
> Section thicknesses should be uniform as much as possible. For variations it must be done gradually.
> Abrupt changes in the thickness should be avoided at all costs.
> Simplicity is the key, the casting should be designed as simple as possible.
> It is difficult to create true large spaces and henceforth large flat surfaces must be avoided.
> Webs and ribs used for stiffening in castings should as minimal as possible.
> Curved shapes can be used in order to improve the stress handling of the cast.
What are the points that should be kept in mind during forging design?
Some of the points that should be followed while forging design are:
> A radial flow of grains or fibers must be achieved in the forged components.
> The forged items such as drop and press forgings should have a parting line that should divide the
forging into two equal halves.
> The ribs in a forging should not be high or thin.
> In order to avoid increased die wear the pockets and recesses in forgings should be minimum.
> In forgings the parting line of it should lie as far as possible in a single plane.
> For ease of forging and easy removal of forgings the surfaces of the metal should contain sufficient
drafts.
10. What do you understand by the Hooke`s Coupling what are its purposes?
The Hooke`s coupling is used to connect two shafts whose axes intersect at a small angle. The two
shafts are inclined at an angle and is constant. During motion it varies as the movement is transferred
from one shaft to another. One of the major areas of application of this coupling is in gear boxes where
the coupling is used to drive the rear wheels of trucks and other vehicles. In such usage scenarios two
couplings are used each at the two ends of the coupling shaft. they are also used to transfer power for
multiple drilling machines. The Hooke`s coupling is also known as the Universal coupling. The torque
transmitted by the shafts is given by :
T= (pie/16) x t x (d) cube
Where T = torque, t = shear stress for the shaft material and d the diameter of the shaft.
11. What kind of materials should be used for shafts manufacturing?
Some of the qualities that should be present in materials for shafts are as follows:
> The material should have a high index of strength.
> Also it should have a high level of machinability.
> The material should possess a low notch sensitivity factor.
> The material must also have wear resistant properties.
> Good heat treatment properties should also be present
The common material used to creates shafts of high strengths an alloy of steel like nickel is used. The
shafts are manufactured by hot rolling processes and then the shaft is finished using drawing or grinding
processes.
12. Why should a chain drive be used over a belt or rope driven drive? State
pro`s and con`s?
The advantages of using a chain drives are:
> In a chain drive no slip occurrence takes place.
> The chains take less space as compared to rope or belts as they are made of metal and offer much
strength.
> The chain drives can be used at both short and long ranges and they offer a high level of transmission
efficiency.
> Chain drives can transmit more load and power as compared to belts.
> A very high speed ratio can be maintained in one step of chain drives.
Some of the cons of using a chain drive are:
> The cost of producing chain drives is higher as compared to that of belts.
> The chain drives must be serviced and maintained at regular intervals and henceforth their cost of
ownership is high comparatively.
13. What are the different types of springs and explain them briefly?
Springs can be broadly classified into the following types:
> Helical Springs: These springs as their name suggests are in coil form and are in the shape of helix.
The primary purpose of such springs are to handle compressive and tensile loads. They can be further
classified into two types: compression helical spring and tension helical spring each having their own
unique areas of application./
> Conical and volute springs: Both these spring types have specialized areas of usage where springs with
adaptable rate according to the load is required. In case of conical springs they are wound so as to have
a uniform pitch while on the other hand volute springs are wound in a slight manner of a parabloid.
> Torsion Springs: The characteristics of such springs is that they tend to wind up by the load. They can
be either helical or spiral in shape. These types of springs are used in circuit breaker mechanisms.
> Leaf springs: These types of springs are comprised of metal plates of different lengths held together
with the help of bolts and clamps. Commonly seen being used as suspensions for vehicles.
> Disc Springs: As the name suggests such types of springs are comprised of conical discs held together
by a bolt or tube.
> Special Purpose Springs: These springs are all together made of different materials such as air and
water.
14. During the design of a friction clutch what are the considerations that
should be made?
In order to design a friction clutch the following points must be kept in mind:
> The material for the contact surfaces must be carefully selected.
> For high speed devices to minimize the inertia load of the clutch, low weight moving parts must be
selected.
> The contact of the friction surfaces must be maintained at all the times without the application of any
external forces.
> Provisions for the facilitation of repairs must be there.
> In order to increase safety the projecting parts of a clutch must be covered.
> A provision to take up the wearing of the contact surfaces must be present.
> Heat dissipaters to take away the heat from the point of contacting surfaces must be there.
15. What are the different types of brakes and explain them briefly?
Brakes can be classified on the basis of their medium used to brake, they are as follows:
> Hydraulic Brakes: These brakes as their name suggest use a fluid medium to push or repel the brake
pads for braking.
> Electric Brakes: These brakes use electrical energy to deplete or create a braking force.
Both the above types of breaks are used primarily for applications where a large amount of energy is to
be transformed.
> Mechanical Brakes: They can be further classified on the basis of the direction of their acting force:
Radial Brakes: As their names suggests the force that acts on the brakes is of radial direction. They can
further be classified into internal and external blades. Axial Brakes: In these types of brakes the braking
force is acting in an axial direction as compared to radial brakes.
17. What are the basis on which the best material for Sliding Contact Bearings
manufacturing?
Some of the important properties to lookout for in the material for sliding contact bearings are as follows:
> Compressive Strength: In order to prevent the permanent deformation and intrusion of the bearing the
material selected should be possess a high compressive strength to bear the max bearing pressure.
> Fatigue Strength: the material selected for the bearing should be able to withstand loads without any
surface fatigue cracks getting created. This is only possible if the material has a high level of fatigue
strength.
> Comfortability: The material should be able to adjust or accommodate bearing inaccuracies and
deflections without much wear and heating.
> Embeddability: The material should allow the embedding of small particles without effecting the material
of the journal.
> Bondability: The bearings may be created by bringing together ( bonding ) multiple layers of the
material. Due to the above reason the bondability of the material should be sufficiently high.
> Thermal conductivity and corrosion resistance: Thermal conductivity is an essential property for bearing
materials as it can help in quickly dissipating the generated heat. Also the material should have a level of
corrosion resistance against the lubricant.
20. Explain in an orderly manner how the force in the member of a truss be
detected using the method of joint.
The steps required to calculate the force are as follows:
> The reaction at the support has to be first calculated.
> Once the reaction is calculated the direction of force of the member is made to make it tensile. On
getting the result to be negative the direction assumed is wrong and this implies the force being
compressive in nature.
> A joint needs to be selected whose 2 members are not known. The lami`s theorem is used on the joint
on which less than three forces are acting.
> After the above process is complete the free body diagrams of the joint needs to be made. Since the
system is in equilibrium the condition of Summation of V and H must result in zero.
> After the above step the resolution of forces method needs to be used on the joint on which more than 4
forces are acting.
21. In order to derive the torsional formulas what are the assumptions taken?
The torsion equation is derived on the basis of following assumptions:
> The shaft material is uniform, throughout the shaft.
> Even after loading the shaft circular remains circular.
> After the application of torques the plain section of a shaft remains plain.
> Any twist that occurs in the shaft remains uniform and constant.
> After the application of torque the distance between any two cross-sectional references remains
constant.
> The elastic limit value of a shaft is never exceeded even after the shear stress induced because of
torque application.
22. What are Bevel Gears and what are its types?
Bevel gears are the type of gears in which the two shafts happen to intersect. The gear faces which are
tooth bearing are conical in shape. They are generally mounted on shafts which are 90 degrees apart but
they can be made to work at other angles as well. The bevel gears are classified into the following types
on the basis of pitch surfaces and shaft angles:
> Mitre Gears: These types of gears are similar to each other ie. they have the same pitch angles and
contain the same number of teeth. The shaft axes intersect at 90 degrees angle.
> Angular bevel gears: When two bevel gears connect at any angle apart from 90 degrees.
> Crown bevel gears: When the two shaft axes intersect at an angle greater than 90 and one of the bevel
gears have a pitch angle of 90 degrees they are known as crown bevel gears.
> Internal bevel gears: In these type of gears the teeth on the gears is cut on the inside area of the pitch
cone.
23. What are the different values that need to be determined in order to
design a cylinder for an ICE?
The following values are needed to be determined:
> Thickness of the cylinder wall: The cylinder walls in an engine is made witness to gas pressure and the
side thrust of a piston. This results in two types of stresses: longitudinal and circumferential stress. Both
the types of stresses are perpendicular to each other and hence it is aimed to reduce the resulting stress
as much as possible.
> Length and bore of the cylinder: The length of the cylinder and the length of the stroke is calculated on
the basis of the formula: length of cylinder L = 1.15 times the length of the stroke (l). L = 1.15(l)
> Cylinder flange and studs: The cylinders are always cast integral as a part of the upper crankcase or in
some cases attached to it by means of nuts and bolts. The flange is integral to a cylinder and henceforth
its thickness should be greater than that of the cylinder wall. The thickness of flange should generally be
between 1.2t-1.4t where t is the cylinder thickness.
The stud diameter is calculated by equating gas load ( due to max pressure ) to the grand total of all the
resisting forces of the studs.
24. What are considerations taken into account while creating a piston head?
The piston head is designed on the basis of the following considerations:
> The crown should have enough strength to absorb the explosion pressure inside the engine cylinder.
> The head must always dissipate the heat of the explosion as quickly as possible to the engine walls.
The thickness of the head is calculated on the basis of another formula which takes into consideration the
heat flowing through the head, the conductivity factor of the material. The temperature at the center and
edges of the head.
> The thickness of the piston head is calculated on the basis of the Grashoff`s formula which takes into
consideration the maximum gas pressure of an explosion , the permissible bending and the outside
diameter of the piston.
What is mechanism?
A mechanism is an assembly of different parts which perform a complete motion and is often part of a
machine.
First Law: Energy can be neither created nor destroyed. It can only change forms. In any process in an
isolated system, the total energy remains the same.
Eg: turning on a light would seem to produce energy; however, it is electrical energy that is converted.
Second Law: The second law of thermodynamics states that the entropy of any isolated system not in
thermal equilibrium almost always increases.
Eg: A car that has run out of gas will not run again until you walk 10 miles to a gas station and refuel the
car.
Third Law: As temperature approaches absolute zero, the entropy of a system approaches a minimum.
Eg: Water in gas form has molecules that can move around very freely. Water vapor has very high
entropy (randomness). As the gas cools, it becomes liquid which can still move around but not as freely.
At this point they have lost some entropy. On cooling further it becomes solid ice where molecules can no
longer move freely but can only vibrate within the ice crystals. The entropy is now very low. As the water
nears absolute zero, the vibration of the molecules diminishes. If the solid water reaches absolute zero,
all molecular motion would stop completely. And at this point the water would have no entropy at all.
What is PS?
Personal Statement. It is something that gives an informative background about an individual.
-Ball bearing
-Roller bearing
-Ball Thrust bearing
-Roller thrust bearing
-Tapered roller bearing
-Magnetic bearings
-Giant Roller Bearing
Who invented the four stroke engine? According to you which one is more
efficient, four stroke engine or a two stroke engine and why?
Nikolaus Otto invented the four stroke engine. Both, two stroke and four stroke have their own
advantages and disadvantages. 4 stroke is more fuel efficient. However, 2 stroke produces more power.
Explain why diesel engine is known as high torque and petrol engine as high
speed engine?
Each power stroke in a petrol engine releases more heat and is converted into mechanical energy due to
a higher rate of burning. This is the reason petrol engine has higher power and acceleration.
Diesel engine is a compression ignition engine with higher compression ratio, therefore extreme pressure
is high. Since the piston of a diesel engine is larger, more torque is delivered in produced.
(ii) IR Sensors- This device detects and/or emits infrared radiation to sense a particular phase in the
environment. Mostly thermal radiation is emitted by all the objects in the infrared spectrum. This type of
radiation is not visible to the human eye but the infrared sensor detects it.
(iii) UV Sensors- These sensors measure the intensity of the ultraviolet radiation. This form of
electromagnetic radiation has wavelengths which are longer than x-rays yet shorter than visible radiation.
UV sensors can discover the exposure of environment to ultraviolet radiation.
(iV) Touch Sensor- A touch sensor acts as a variable resistor based on the location where it is sensed.
Proximity Sensor- A proximity sensor detects the presence of objects that are placed in close proximity
without any point of contact.
Since it burns in the gaseous phase, it results in less corrosion and engine wear.
Disadvantages
Since complete combustion occurs, more heat is liberated which is not advised for a long journey as the
engine will get over heated.
When power is driven from driver pulley to driven pulley by means of belt , it is known as belt drive.
In open belt drive both the pulleys run in the same direction and in cross belt drive both the pulleys
run in opposite direction to each other.
o Misalignment of pulleys.
o Capacity of machine.
Jockey pulley is used to increase the contacting area in between the belt and pulley and also used to
press the belt for giving tension.
The outer surface or face of rim of the pulley is made in convex form to keep the belt in center when
it is in movement, it is called crowning.
o The movement of belt upon the face of rim or outer surface of driver and driven pulleys within
o If the belt is loosely fitted on pulleys, it slips down which is called slip in belt drive.
o The distance between two pulleys should not be less than three times the diameter of the
larger pulley.
o The slack side should be uppermost which may increase the arc of contact.
o The ratio of diameter of both the pulleys should not exceed 6:1.
o The main advantages of V belt are it has more gripping power, long life and it occupies less
space.
o Disadvantages are it is not fit for long distances and cross belt drive.
o To transmit power.
Worm drive consists of a worm and worm wheel and the worm wheel is always driven by the worm.
It is suitable for heavy loads and also for speed reduction.
o Addendum is the distance from the top of tooth to the pitch circle.
o Dedendum is the distance from the root to the pitch circle of gear tooth.
It is distance in straight line from tooth to tooth along the pitch circle.
What Is Module?
It is the ratio between the pitch diameter and the number of teeth in the gear.
Diameteral pitch is the ratio between the number of teeth of a gear and the pitch circle diameter.
Which Gears Are Used To Connect The Shafts Lying In The Same Plane?
o Herringbone Gears . Double helical gears are known as Herringbone gears. These gears
have teeth in series on both sides from the centre in the inclined position to the axis. These
type of gears are used to transmit motion at high speed with heavy load without producing
noise.
o Helical Gears. These type of gears have teeth in series of single way in an inclined position.
Helical gears are used to transmit the motion at high speed without producing noise.
Which Gears Are Used To Connect The Shafts Which Intersect At Same Angle?
Which Gears Are Used To Connect The Shafts At An Angle But Lying In The Same Plane?
o Spiral gears
Rack is a flat bar having straight teeth in series .It is meshed with a pinion having straight teeth like
spur gear. These type gears used in carriage of lathe and milling machine table.
o Friction bearings. This type of bearings contact that shaft directly such as bush bearing
,journal bearing etc. These bearings generally made of cast iron ,brass and gun metal.
o Anti-friction bearings. These type of bearings have rolling elements such as balls, rollers etc.
While removing the damaged lining it helps to melt the lining at low temperature and it helps to
spread over the molten metal on the bearing surface.
o Ball bearing is generally used on high speed with light load because it has point contact.
o Roller bearing is generally used on high speed with heavy load because it has line contact.
A taper roller bearing is used to carry heavy loads because it has taper rollers instead of plain
cylindrical rollers.
It is generally used on high speed with light load because its bearing metal controls the heat.
The main reasons are, inadequate lubrication ,overloading ,miss-alignment and bearing in defective
condition.
What Are The Various Types Of Bearings?
o Bush Bearing. It is a plain cylindrical bearing made of brass , gun metal ,cast iron etc. Its
inner bore is finished and made running fit to the shaft. It is generally used on low speed
o Ball bearing. It consists of outer race, inner race, steel balls and cage. The balls are rolling
themselves in the tracks between the outer and inner races ,bearing is fitted on shaft while
its outer portion is fixed in housing .Balls have point contact and are free in the races,friction
It is a split bearing having two halves which are made of brass, gun metal, etc. Its outer ends have
collar on both sides. IT is fitted in the housing generally made of cast iron. It is used where the
supporting pressure of the bearing is at right angle to the shaft axis.
o For running at slow and high speed carrying light and heavy loads.
What Is A Cam?
A cam is a cylinder, plate or other solid with curved outline which is designed to convert rotary
motion into timed irregular motion on the follower which is in contact with it.ie,cams rotary motion can
be changed to reciprocating motion.
o Radial cam. On this cam the follower operates in a plane perpendicular the axis of the
camshaft .
o Main shaft
o Counter shaft
o Crank shaft
o Splined shaft.
Commonly used followers are, Pointed , Flat faced, Roller and Spherical faced.
A Screw jack consists of a body and a square threaded screw rod. Its screw rod has a head and a
revolving pad. This screw rod acts on both directions according to the action of the lever attached
with ratchet arrangement with the handle. It is used to lift the loads therefore it is mostly used by
motor mechanics.
Clutch is used to connect and disconnect the driving and driven units of a machine. It does the
function when machine speed is changed after stopping the driving unit.
It is a device used to connect two shafts. These are generally used to increase the length of shafts.
It is very common type of coupling used to connect the shafts by means of two flanges. Two cast
iron flanges are fitted with key to the ends of the two shafts to be connected and fastened together
by means of bolts and nuts.
It connects the shafts with soft materials such as rubber, leather, canvas etc. It adjusts the little
misalignment and controls the vibrations also. It is generally used electric pumps.
Pulley block is a block in which two or three group of pulleys are used with a rope to lift and heavy
loads. The load is tied in the hook of the movable block and the effort is applied at the end of the
rope which comes through the fixed pulley block.
It is a hollow piece which is used with key to connect the shafts. It may be found in cylindrical
muff,half lap muff or split muff type. A gib head key or a saddle key is inserted between the coupling
and shafts through out for connecting the shafts.
It consists of a cylinder and ram. The oil is forced into the cylinder. The load is lifted by this jack
according to the pressure of the oil. In its working system the oil is filled through the oil plug in the oil
reservoir. It has a tube at the lower en d and a non return valve. When the lever is operated up and
down, plunger moves up in the tube supplying the oil and it down the non return valve which allow
the oil into the cylinder which causes the ram raises. The ram raises according to the pressure of the
oil which lift the load accordingly.
It consists of two grooved pulleys which are fixed side on the same spindle having chain also. While
another pulley is fitted with clamp in which a lifting hook is provided. One chain connects the hanging
pulley. When a chain is pulled by hand then all the pulleys start functioning and the hook carries the
load. In this way the load is lifted to a required height.
What Is The Formula To Find Out The Length Of A Belt In An Open Belt Drive?
What Is The Formula To Find Out The Length Of A Belt In A Closed Belt Drive?
L = 2C + 1.57 (D +d ) + (D+d)2/ 4C
How To Calculate The Number Of Teeth In A Gear If Given The Module And Pitch Circle
Diameter?
Pipe threads are grouped in certain ranges such as 1/4” to 3/8” pipe threads have 19 T.P.I , ½ “ to 7/
8” pipe threads have 14 T.P.I, 1” and above size pipe threads have 11 T.P.I . Pipe threads may be
either straight or tapered.
Commonly used pipe fitting accessories are : Socket, Reducing socket, Cross, Union, Stop valve,
Elbow, Union, Plug, Flange, Tee.
It is used to hold the pipe firmly and it is fit for rotation on both ways.
Explain About Common Types Of Pipe Materials And How Are Pipes Specified?
Pipes are commonly made of cast iron , steel, copper, lead, zinc, galvanized iron(G.I) wrought iron ,
aluminium and also cement and plastic pipes are used. Generally pipes are specified by the length,
material, bore size.
o Threads joints should be fixed applying red lead, white lead, dry point etc. in the threads,
bound the pipe threads using twine and tightened them fully with a suitable wrench.
o Flanged joint should be fixed using a washer of rubber, leather, card board or soft metal in
Generally tools used in pipe fittings are Pipe vice, Pipe wrench, Pipe die, Pipe tap, Chain wrench,
Chisel, Hammer, Reamer and Pipe cutter.
o Pipe vice. It is used to hold the pipe firmly while cutting, threading etc.
This joint is generally used to connect cast iron pipes which are buried in ground .This is also
suitable for straight pipe line carrying water and this joint has less rigidity.
This joint is used to carry the piping system at high pressure. This joint is provided with gland and
stuffing box which make the joint perfectly steam tight. To prevent leakage asbestos packing is
provided.