Professional Documents
Culture Documents
Main Moshell Commands
Main Moshell Commands
amos site#
lt all
alt (active alarms)
lga (history os alarms)
lga | grep -i T1phy (shows on and off time for alarms)
lgv (node in node out)
lge (evry minute activities on site)
lgo (changes on site)
lgs (RAX/TX crashes)
lgs -m 48h (gives hardware crashes)
lgd 60: downtime
hc-????
cabr- see restarts of nodeB
cvls (daily activies on site)
llog (log for restarts on the site)
lgsavemo (To get the history of the site for the working)
pmr -m 2 ( two hourly) (1 gives RSSI -97 to -108)
pmr -m 0.25 (quarterly 15 min rop)
st t1(status of T1's)
lst t1 (shows T1s)
pget t1 (status of T1)
st ima (IMA group status)
lh ru fui get devstat- current generated form the sctor with TMA
st link
st ethernet
get iub plane (gives if the site is ip or atm)
pmx -m 2 t1 s -a (error secs)
get . nodebfunction (it will provide you with the # of channel elements available
(DL and UL)(1rax board = 128ch elements, i.e., 512, then 4 rax board is needed (4 x
128 = 512) sometimes, the rax board defined is more than what is physically at the
site)
HXV3386> get . maxtot-max total power
hget rbs rbslocalcell|localcellid|maxDlPowerCapability
readclock
RNC level: can apply grep to all commands (| grep "yyyy-mm-dd")(| grep DXU0040)
amos RNC#
lt all
pmr (8 | grep DXU0040)(8 | sort -k4 -n)
pmx DXU0040 pmNoSystemRabReleaseSpeech �m 4 -a (4 hours and aggregate(-a), sum(-s))
pmx DXU0040 pmnosysRelSpeechNeighbr (gives number of drops due to missing nbrs)
pmx DXU0040 pmnosysRelSpeechUlSynch �m 4 -a (gives drops due to ULsync, last 4
hours aggregated)
alt (active alarms)
get . loadsharingrrcenabled (Should be true(1) in order to activate the load
sharing)
lget utrancell=DXU1858 loadsharingcandidate (shows all the neighbors for which the
loadsharingcandidate is true(1) i.e activated)
lget DXU4020C.*DXU4020Z qoffset2sn (shows the qoffset2sn for the respective source
and target cells)
lget DXU0167.*DXU2479 qoffset2sn (shows the qoffset2sn for the respective source
and target sites)
ced | grep DXU0040 (Utran audit)
cedr | egrep '(DXU0167|DXU2479)'|sort +6n (used during live monitoring, shows all
counters related to power utilization, can be sorted columnwise)
cedr | egrep '(DXU0167|DXU2479)' (used during live monitoring, shows all counters
related to power utilization)
lget utrancell=CNU1732 frequencyrelationtype 0 (gives all the INTRA defined nbrs
for a site)
lget utrancell=CNU1732 frequencyrelationtype 1 (gives all the INTER defined nbrs
for a site)
lget cnu3229A frequencyrel (same as above)
get utrancell=DXU0040 maximumtransmissionpower
get utrancell=DXU0040 hoType
get utrancell=cnu1970 adminis (gives unlocked)
get utrancell=cnu1970 cellreserve (gived reserved)
get UTRANcell=cnu1970 qrxlevmin|usedFreqThresh2dEcno|sIntersearch|cpich|
usedFreqThresh2dRscp|MaximumTransmissionPower (counters can ce clubbed, can check
any possible counters)
lki (will show consistent and in-consistent Iub links all)
h lki (help on lki)
str | grep DXU5850A (Shows the status of the cell DXU5850A)
get utrancell=HXU0470 scr (scrambling code)
Pmx -m 2 aal2ap=b265 pmUnSuccOutConnsRemoteQosClass (getting Iub congestion -remote
last 2 hours)
get PRSJU0033 rbsid (gives the bnum of the site)
get utrancell=PRSJU0010 (gives al information about the cell)
lget utrancell=TXV42374 directedretry
hget utrancell=HXU4921 Administrativestate|operationalstate|cellreserved
rbs: lgo
rnc: lgo | grep ####
amos -v corba_class=5,nm_credential=/home/v94868/Ericsson/OMSec/ssucredentials.xml
SNANTX78CRBR10
to check ROP
lget . defaulthotype
llog(restart info)
get . outputpower
get externalTMA
lget utrancell=HXU4182 hsiflsmarginusers|hsiflsthreshusers|iflsmode|
pathlossthreshold
lget coveragerelation ref
lget utrancell=HXU25551 coveragerelation
get UtranCell=HXU25551,CoverageRelation
Hardware:
board errors
CBU errors
RSSI
overshooting
pilot pollution in the area
vswr
transport issues
SC collision
IFHO failures
Neighboring sites with alarms or cell down time
HSIFLS
this iflsmode will tell that when to trigger eaither 0=rar_est 1=Upswitch_att,
2=Rab_est_or_upswitch_att
hsIflsThreshUsers
First inter-frequency load sharing candidate cells must be defined, by defining
coverage relations and setting the hsLoadSharing and/or dchLoadSharing attributes
to ON. HSDPA load sharing can then be activated by setting hsIflsThreshUsers to a
value other than 0. Non-HSPA load sharing can then be activated by setting
dchIflsThreshPower and/or dchIflsThreshCode to a values other than 0.
this is what i under shood i am sharing to you
if we are keep 0 thenif power congestion ifls will not trigger
if you are keeping cod as 0 the n also it will not trigger
it will trigger only wehn you are keep 50
ok i will try for i cell & share
NON HS
ok so you have total power and than you have power used each cell for cs traffic.
the ideally is to keep that power as low as possible. and whateever the power used
on cs traffic rest are for the hs. the graph that shows the power utilization for
yoru cs are called the non-hs power utilization
you look into this to make judgement if you cell is heavily congested or not. if it
is not than you can cahnge your admission parameters cause many cases they are set
to very high
Date: 2013-07-19
Object Counter 15:00 16:00 17:00
UtranCell=HXU52511 pmNoFailedRabEstAttemptLackDlHw 0 0 0
UtranCell=HXU52511 pmNoFailedRabEstAttemptLackDlHwBest 0 0 0
UtranCell=HXU52512 pmNoFailedRabEstAttemptLackDlHw 0 0 0
UtranCell=HXU52512 pmNoFailedRabEstAttemptLackDlHwBest 0 0 0
UtranCell=HXU52513 pmNoFailedRabEstAttemptLackDlHw 0 0 0
UtranCell=HXU52513 pmNoFailedRabEstAttemptLackDlHwBest 0 0 0
UtranCell=HXU52514 pmNoFailedRabEstAttemptLackDlHw 10 6 0
UtranCell=HXU52514 pmNoFailedRabEstAttemptLackDlHwBest 8 6 0
UtranCell=HXU52515 pmNoFailedRabEstAttemptLackDlHw 56 27 0
UtranCell=HXU52515 pmNoFailedRabEstAttemptLackDlHwBest 46 12 0
UtranCell=HXU52516 pmNoFailedRabEstAttemptLackDlHw 0 0 0
UtranCell=HXU52516 pmNoFailedRabEstAttemptLackDlHwBest 0 0 0
UtranCell=HXU5251A pmNoFailedRabEstAttemptLackDlHw 0 0 0
UtranCell=HXU5251A pmNoFailedRabEstAttemptLackDlHwBest 0 0 0
UtranCell=HXU5251B pmNoFailedRabEstAttemptLackDlHw 0 0 0
UtranCell=HXU5251B pmNoFailedRabEstAttemptLackDlHwBest 0 0 0
UtranCell=HXU5251C pmNoFailedRabEstAttemptLackDlHw 0 0 0
UtranCell=HXU5251C pmNoFailedRabEstAttemptLackDlHwBest 0 0 0
UtranCell=HXV62511 pmNoFailedRabEstAttemptLackDlHw 9 6 0
UtranCell=HXV62511 pmNoFailedRabEstAttemptLackDlHwBest 9 8 0
UtranCell=HXV62512 pmNoFailedRabEstAttemptLackDlHw 15 36 0
UtranCell=HXV62512 pmNoFailedRabEstAttemptLackDlHwBest 14 32 0
UtranCell=HXV62513 pmNoFailedRabEstAttemptLackDlHw 8 6 0
UtranCell=HXV62513 pmNoFailedRabEstAttemptLackDlHwBest 6 6
***********************************************************************************
*************************************************
UtranCell hsdschInactivityTimerCpc long
-----------------------------------------------------------------------------------
-------------------------------------------------
Time after which a CPC activated connection with low throughput is downswitched
from CELL_DCH to CELL_FACH. This parameter is used instead of hsdschInactivityTimer
for CPC activated connections.
Special value
-1: corresponding parameter on MOC ChannelSwitching is used
Resolution: 5
Dependencies: Used if the feature InactivityTimerCellConfig is activated and if the
parameter value is defined. If not the corresponding parameter on MOC
ChannelSwitching is used.
Feature: InactivityTimerCellConfig
Change takes effect: New connections
Unit: 0.1 s
Range: -1, 0 to 1000, Default=-1
***********************************************************************************
*************************************************
***********************************************************************************
*************************************************
UtranCell hsdschInactivityTimer long
-----------------------------------------------------------------------------------
-------------------------------------------------
Time after which a connection with low throughput is downswitched from HS-DSCH to
CELL_FACH.
Once the throughput on both the uplink and downlink has fallen below the value of
ChannelSwitching::downswitchTimerThreshold, a downswitch to FACH/RACH is normally
requested after this length of time. However, the downswitch is not requested if
the throughput has subsequently increased above the value of
ChannelSwitching::downswitchTimerThreshold. If CELL_FACH state is not available,
the connection is switched down to IDLE state. Applicable only for radio
connections without CPC.
Special values:
-1: corresponding parameter on MOC ChannelSwitching is used
7200: only for internal use.
Dependencies: Used if the feature InactivityTimerCellConfig is activated and if the
parameter value is <> -1. If not the corresponding parameter on MOC
ChannelSwitching is used.
Feature: InactivityTimerCellConfig
Change takes effect: New connections
Unit: s
Range: -1, 1 to 255, 7200, Default=-1
***********************************************************************************
*************************************************
for parameters
mom MO parametername
for counters
pmom MO countername
HOW TO MOBATCH
VLOOKUP(B2,Sheet1!A:V,MATCH(D2,Sheet1!A$1:V$1,0),0)
lgaes -s 20130901-alarms,event,crashes
llog
lgd-downtime
st t1
pmr -m 3 -r 25-report no 25 to show the packetloss
lh rax te log read | grep -i error-RAX check
lh tx te log read | grep -i error-Tx Check
s+
AAL2 BO
mobatch -v
corba_class=5,nm_credential=/home/v94868/Ericsson/OMSec/ssucredentials.xml
AUSSTXBWRNC002,AUSUTXNICRBR11,AUSUTXNICRBR12,AUSUTXNICRBR13,AUSUTXNICRBR15,AUSUTXNI
CRBR17,AUSUTXNICRBR18, 'lt utranrelation;lget . frequencyrelationtype 0' AUS_1002
v94868@all2e2cx2> cd AUS_1002
v94868@all2e2cx2> grep UtranCell ./*.log > AUS_1002.txt
v94868@all2e2cx2> gzip AUS_1002.txt
v94868@all2e2cx2> pwd