Professional Documents
Culture Documents
Ab Initio Monte Carlo Simulations of The Acidic Dissolution of Stainless Steels Further Insights Into The Mechanisms PDF
Ab Initio Monte Carlo Simulations of The Acidic Dissolution of Stainless Steels Further Insights Into The Mechanisms PDF
Using Ab initio based Monte Carlo simulation techniques (AbMC), dissolution kinetics in acidic media was evaluated for different
stainless steels (SS) as a function of their chemical composition, with particular attention paid to the role of transition metals series
(TM). The elementary dissolution events at the atomic scale were treated as stochastic processes, from which dissolution probabilities
were deduced. Two determining factors emerge as critical for the control of dissolution kinetics: the bonding energy of an alloying
element in the SS matrix and its standard electrochemical potential. The first reflects the ability of an element to form stronger (Mo,
Nb, Ni etc.) or weaker (Cr, Cu, Sn etc.) bonding than Fe, and the second refers to its facility to dissolve under an applied potential.
High bonding energies and high standard potentials lead to a strong dissolution resistance (Mo), whereas low bonding energies and
low standard potentials induce high dissolution kinetics (Sn). The intermediate situations: high-bonding energy and low standard
potential (Nb) or low bonding energy and high standard potential (Cu) usually lead to moderate dissolution regimes with a strong
impact on the dissolution mechanisms.
© The Author(s) 2018. Published by ECS. This is an open access article distributed under the terms of the Creative Commons
Attribution 4.0 License (CC BY, http://creativecommons.org/licenses/by/4.0/), which permits unrestricted reuse of the work in any
medium, provided the original work is properly cited. [DOI: 10.1149/2.1321810jes]
Manuscript submitted April 30, 2018; revised manuscript received July 24, 2018. Published August 4, 2018.
In a recent paper, we developed a numerical approach (the details Physical Modeling and Computational Method
of which are published elsewhere)1 that describes the dissolution pro-
An overview of the AbMC simulation methodology.—The phys-
cess of a metallic alloy by means of the Ab initio based Monte Carlo
ical model used in our simulations is based on the transition state
simulation techniques (AbMC) method. We succeeded in formulat-
theory (TST)12–14 with a view to formulating dissolution probabilities
ing a general expression of the dissolution probability of any given
at the atomic scale.15–18 These probabilities are then used to identify
SS grade as a function of its chemical composition, crystallographic
all the possible dissolution events that may occur on the surface of a
microstructure and the environmental variables (pH and applied po-
given SS grade under given environmental conditions. At this stage,
tential). Our findings pointed out the effect of the chemical nature of
we do not consider any passivation reaction, since we are interested in
a dissolving atom and the number of its nearest neighbors. A critical
very acidic dissolution conditions. We assigned to each surface atom
coordination number (CCN) was then defined, above which the dis-
an activation energy that determines its dissolution probability as a
solution probability of a surface atom is too low to contribute to the
function of its surface position and the chemical composition of its
dissolution rate. It was then shown that increasing the Cr content of
closest neighbors. In the presence of an applied potential ϕ (eV)
ferritic SS does not change the CCN, however, it makes the dissolution
at the SS/electrolyte interface, the dissolution probability (ϑdiss ) of a
process easier because of the low Fe-Cr bonding energy. The addition
surface atom j of a Fe-xCr SS is given by:
of Mo was found to involve multiple CCN, belonging to different
crystallographic orientations, which also resulted in a substantial de-
α j iN E b, i
j α j z j ϕ j
crease of the dissolution kinetics. These results are consistent with ϑdiss, j = ϑo exp − exp −α j · p H exp −
previous works2–9 that have also reported that the dissolution prob- kB T kB T
ability of various Tc base alloys depends strongly on Tc contents. [1]
i
In these works, the most active surface atoms are found to act as a E b, j is the bonding energy of the surface atom with its
site-blocking element at surface kinks and step-edges. ith nearest neighbor, the pre-exponential factor given by ϑo =
The present work seeks to extend our approach to both ferritic Fe +x.E Cr )
kt k BhT exp( z.((1−x).E
2k B T
) relates the vibration frequency of the sur-
and austenitic steels and to consider the effect of more transition or face atom and the average value of its chemical potential expressed
post-transition alloying elements which, together with Fe, Cr and Mo in terms of the chemical composition of Fe-Cr SS. Z , k B , T, h are
offer a large panorama of 3d TM (Fe, Cr, Ni, Mn and Cu) and 4d TM respectively the coordination number of the ferritic bcc structure, the
(Mo, Nb and Sn) currently used in stainless steel making. Boltzmann constant, the temperature and the Planck constant. kt is
The interest of this work lies in the need to understand the role a transmission coefficient related to the frequency of the vibrational
of alloying elements in controlling dissolution kinetics, an issue of a mode responsible for converting the activated complex to the product
practical implication usually involved in picking and localized corro- in the TST. α j is the symmetry factor counting for the fraction of the
sion. The objective is to clarify the link that may exist between the interfacial potential at the interface which helps to lower the energy
chemical composition of a given SS, its microstructure and the result- barrier and z j being the valence of the dissolving atom.
ing dissolution kinetics and surface morphologies. The example of i
All E b, j energies are deduced from ab initio calculations. The
localized corrosion of SS is worth noting in this respect, as the active effective electrical potential ϕ j felt by a surface atom may depend
dissolution is known to be a critical step in the stabilization process on the chemical composition of the surface,19 particularly for highly
either in pitting or crevice corrosion.10 Therefore, understanding the alloyed surfaces. This effect was first neglected in the previous work1
metallurgical factors controlling dissolution kinetics is a matter of and we will show in this work that this assumption, even if it remains
both practical and theoretical concerns. The findings may be used to valid for high electrical fields (pickling and electropolishing regimes),
interpret the experimental measurements and develop more consistent may not be appropriate for low fields (corrosion regime).
approaches for the prediction and the design of SS.11 A simple MC scheme with a transition probability based on
Equation 1 is then used to obtain the dissolution dynamics of a
given SS microstructure. An iteration procedure is implemented in
∗ Electrochemical Society Member. the simulation in which the dissolution probability of a surface atom
z
E-mail: Brahim.Malki@simorg-computing.fr is subjected to a MC decision process. For each step, a normalized
Downloaded on 2018-08-16 to IP 88.162.207.150 address. Redistribution subject to ECS terms of use (see ecsdl.org/site/terms_use) unless CC License in place (see abstract).
C704 Journal of The Electrochemical Society, 165 (10) C703-C709 (2018)
Pure α-Fe cell with 2 atoms Pure γ-Fe cell with 4 atoms
2E T (Fe)−E T (Fe2) 4E T (Fe)−E T (Fe4)
E coh = 2 E coh = 4
2E T (Fe)−E T (Fe2) 4E T (Fe)−E T (Fe4)
E Fe−Fe = 8 E Fe−Fe = 24
Downloaded on 2018-08-16 to IP 88.162.207.150 address. Redistribution subject to ECS terms of use (see ecsdl.org/site/terms_use) unless CC License in place (see abstract).
Journal of The Electrochemical Society, 165 (10) C703-C709 (2018) C705
a) 3d TM in ferritic SS b) 4d TM in ferritic SS
1,5 1,6
0,8 0,8
0,4 0,4
0,0 0,0
Fe Cr Ni Mn Cu Fe Mo Nb Si Sn
c) 3d TM in austenitic SS d) 4d TM in austenitic SS
1,0 1,0
0,8 0,8
0,5 0,5
0,3 0,3
0,0 0,0
Fe Cr Ni Mn Cu Fe Mo Nb Si Sn
Figure 2. Histograms of the bonding energies of various TM in ferritic (a and b) and austenitic (c and d) stainless steels; individual bond energies are much lower
in austenitic system than ferritic one, but the high coordination number of fcc structure makes the cohesive energies of the two systems rather comparable.
will exhibit a strong tendency to dissolve unlike the rest of the 3d TM. Dissolution mechanisms in FeCr based ferritic steels.—In this
This effect cannot be found in 4d TM due to the large spatial extent of section, we examine the role of some alloying elements in the disso-
the 4d-orbitals (far beyond the first nearest neighbors), which forces lution mechanisms of both ferritic and austenitic SS. The influence of
the electrons to always participate in the formation of the chemical alloying elements on the dissolution probability is analyzed on both a
bond. metallurgical and an electrochemical level. The metallurgical level is
a) b)
Cr Cu
Fe
0.05e -Å-3
Figure 3. Projected electronic density around some alloying
elements (Cr, Cu, Mo and Sn) obtained by subtracting electronic
(100) charges before and after their insertion in a α-Fe matrix; these
changes in the partial charges around an element (negative in
c) d) blue and positive in red and of the order of 0.05e− /Å3 ) reflect the
mode of formation of the chemical bond of the given element.
Mo Sn
-0.05e -Å-3
Downloaded on 2018-08-16 to IP 88.162.207.150 address. Redistribution subject to ECS terms of use (see ecsdl.org/site/terms_use) unless CC License in place (see abstract).
C706 Journal of The Electrochemical Society, 165 (10) C703-C709 (2018)
Table II. Calculated cohesive energies of some transition metals. icantly high for Cr, which is enhanced by the slight decrease in the
induced bonding energies (Figure 2). The result is a multiplication of
3d TM Ti V Cr Mn Fe Ni Cu Zn the initiation sites extended to higher coordinated atoms up to CN = 6
within the (110) dense planes, as shown in Figure 4b. These findings
Ecoh (eV) 4.9 5.2 4.1 2.8 4.4 4.5 3.3 1.4 illustrate the strong oxidability of Cr which will readily form a passive
4d TM Zr Nb Mo Ag Cd Sn film provided that the pH and potential conditions are fulfilled.
Ecoh (eV) 5.4 7.5 7.9 6.8 1.2 2.9 In general, one would expect antagonistic effects from the alloying
elements depending on the polarization level. This is the case for Cu
Table III. Standard potentials of some transition metals. for instance, which exhibits weak bonding energies (see Figure 2) and
element Fe Cr Ni Cu Mn Mo Nb Sn Si hence a certain tendency toward bond breakdown, however, its high
E0 (V/SHE) −0.45 −0.75 −0.25 0.34 −1.14 −0.20 −1.09 −0.14 −0.80 standard potential is likely to reduce the dissolution probability. This
effect is also evident for Sn but to a lesser extent. On the contrary, Nb
with its tendency to form strong bonds has, nonetheless, a very low
represented by the pre-exponential term of Equation 1, where the effect standard potential. A compensating effect is therefore expected in this
of bonding energies was previously demonstrated. The electrochemi- case.
cal level refers to the effect of an electrical field at the SS/electrolyte To better illustrate these effects, here is a detailed simulation of
interface on the magnitude of the energy barrier that a surface atom the acid dissolution of a ferritic Fe20Cr4Cu SS at pH 0 (Figure 5). To
must cross to dissolve toward the electrolyte. The expression ϕ j of carry out the study, we used to analyze first the metallurgical contri-
Equation 1 includes a reference to the standard potential of a given bution alone by setting ϕ j = 0 eV for all elements of the SS (Figure
alloying element j, from which the local electrical potential is defined. 5a). Then, we added the electrical contribution in a second step (Fig-
We use the standard potential of each alloying element at pH 0 as a ure 5b). As shown by the inserted current transients in Figure 5a, the
reference for ϕ j overpotentials33 (see Table III). metallurgical effect of Cr and Cu is revealed by the acceleration of the
These two critical aspects concerning the role of alloying elements dissolution dynamics due to the high dissolution probabilities induced
are illustrated in the dissolution patterns obtained for pure α-Fe and by their weak bonding energies. This is reflected in the dissolution
α-Fe17Cr monocrystalline structures at pH 0 and ϕ Fe = 0 eV (see patterns by an increase in the density of the initiation sites, extended
Figure 4). In the absence of alloying elements, such as in the case to higher coordinated atoms. Considering the electrical contribution
of pure iron, the dissolution proceeds along the most densely packed of alloying elements (ϕ Fe = 0 is set only for Fe), a significant de-
planes (110) in blue in Figure 4a (for more details see our previous crease of the dissolution currents is obtained, likely due to the high
paper).1 The most active neighborhood configuration that governs the standard potential of Cu. Some of the initiation sites are pinned on
experimentally observed dissolution kinetics is found to be the 4 near- the surface by Cu atoms during the dissolution process, leading to
est neighbors system (with a CN = 4, i.e. kink atoms). Conversely, in a rapid depletion of less coordinated atoms. This surface-blocking
the presence of alloying elements, this primary dissolution mechanism scheme is comparable to that observed for Mo but with a rather dif-
undergoes significant changes depending on the nature of the alloying ferent mechanism.1 At the macroscopic level, this behavior results in
element and the applied potential, Figure 4b illustrates the effect of a gradual shift of the equilibrium potential toward higher values,34 a
Cr. Regarding the applied potential (ϕ Fe = 0 eV which implies that fact that is not explicitly integrated in our simulation.
ϕCr = +0.3 eV), the dissolution probability is found to be signif-
Dissolution mechanisms in FeCrNi based austenitic stainless
steels.—The purpose of this section is to investigate the effect of
before dissolution after dissolution
some alloying elements on the acidic dissolution mechanisms of Ni-
a) Pure α -Fe bearing austenitic SS. The transition from a bcc (8 NN) to fcc (12
NN) structure substantively changes the neighborhood configuration
of surface atoms. For a Fe18Cr8Ni SS, for example, there are up to
450 neighborhood possibilities. An immediate consequence is that the
(110)
resulting dissolution probability spectrum will extend to several crys-
(110)
tallographic systems, and this will necessarily affect the dissolution
kinetics.
Figure 6 shows the average dissolution probability of a Fe18Cr8Ni
(110)
polycrystalline structure at two different polarization levels: a)
ϕ Fe = 0 eV and b) ϕ Fe = +0.4 eV, along with the corresponding
dissolution patterns. It appears from this result that the acid dissolu-
b) Fe17Cr SS
tion of austenitic SS is more complex than that of ferritic SS, since
it involves several critical coordination numbers at the same time. At
low polarization levels (corrosion regime), the initiation sites are lo-
calized on the edge of the (111) dense planes having 5NN and 6NN
as the CCN, whereas for high polarization levels (pickling regime)
7NN/(111) system and higher dominate the dissolution dynamics.
This complex distribution of the dissolution probability is expected
to generate different dissolution kinetics depending on the chemical
composition of a surface and the crystal orientation.35,2,36
In addition, the role of alloying elements can be regarded as similar
to that of ferritic SS with, however, more complex antagonist effects.
Figure 7 shows the dissolution probability obtained at a high applied
potential ϕ Fe = 0.45 eV of some austenitic SS selected to illustrate
Fe Cr sites with CN = 6
the role of Cr, Ni, Nb, Cu and Sn. As is expected, the beneficial effect
Figure 4. Dissolution patterns of: (a) a pure monocrystalline α-Fe and (b) a
of the Nb, which is a priori similar to Mo from a metallurgical point of
ferritic Fe17Cr SS in highly acidic conditions (pH 0 and ϕ Fe = 0) before view (Figure 1), is somewhat canceled out by the electrical effect due
and after few iterations of simulation; the most active sites in α-Fe are those to its low standard potential (Table II). In the case of Cu and Sn, which
localized on the edge of the (110) dense planes. The addition of Cr will increase both induce weak chemical bonds, the metallurgical effect is stronger
the number of initiation sites localized even in the (110) planes. for Cu than for Sn. A deactivation of several dissolution systems of
Downloaded on 2018-08-16 to IP 88.162.207.150 address. Redistribution subject to ECS terms of use (see ecsdl.org/site/terms_use) unless CC License in place (see abstract).
Journal of The Electrochemical Society, 165 (10) C703-C709 (2018) C707
4000 4000
Fe
3000 3000
2000 Cr 2000
1000 1000
Cu Fe
Cr
0 Cu
0
0 50 100 150 200 0 50 100 150 200
Iterations Iterations
Fe Cr Cu sites with CN = 6
Figure 5. Dissolution patterns and the corresponding current transients of Fe17Cr4Cu SS in acidic media (pH 0) and the corresponding corrosion patterns: (a)
ϕ j = 0 for all elements and (b) ϕ Fe = 0 for Fe only; the effect of Cr and Cu is revealed by the acceleration of the dissolution rate due to the weak bonds
induced by Cu.
1 1
10 10
CCN > 5 0 CCN > 6
0 10
10
Dissolution probability
Dissolution probability
-1 -1
10 10
-2 -2
10 10
-3
10
-3 10
-4
10
-4 10
-5
10
-5 10
-6
10
-6 10
1 2 3 4 5 6 7 8 9 10 11 12 1 2 3 4 5 6 7 8 9 10 11 12
Coordination Coordination
Figure 6. Calculated dissolution probability of a polycrystalline Fe18Cr8Ni SS in very acidic media and the corresponding corrosion patterns: a) ϕ Fe = 0 eV
and b) ϕ Fe = 0.4 eV ; depending on the applied potential the dissolution mechanism may involve multiple crystallographic systems at the same time.
Downloaded on 2018-08-16 to IP 88.162.207.150 address. Redistribution subject to ECS terms of use (see ecsdl.org/site/terms_use) unless CC License in place (see abstract).
C708 Journal of The Electrochemical Society, 165 (10) C703-C709 (2018)
Fe20Cr18Ni Fe20Cr18Ni4Cu
1 1
10 10
0 CCN > 6 0
CCN > 3
10 10
Dissolution probability
Dissolution probability
-1 -1
10 10
-2 -2
10 10
-3 -3
10 10
-4 -4
10 10
-5 -5
10 10
-6 -6
10 10
1 2 3 4 5 6 7 8 9 10 11 12 1 2 3 4 5 6 7 8 9 10 11 12
Coordination Coordination
1
Fe20Cr18Ni4Nb Fe20Cr18Ni4Sn
10 1
10
0
CCN > 5 CCN > 5
10 0
10
Dissolution probability
Dissolution probability
-1 -1
10 10
-2 -2
10 10
-3 -3
10 10
-4 -4
10 10
-5 -5
10 10
-6 -6
10 10
1 2 3 4 5 6 7 8 9 10 11 12 1 2 3 4 5 6 7 8 9 10 11
Coordination Coordination
Figure 7. Dissolution probabilities of different austenitic SS grades selected as best illustrating the role of Cr, Ni, Nb, Cu and Sn obtained at pH 0 and highly
applied potential ϕ Fe = 0.45 eV.
low coordination is then obtained (CCN >3 for the F20CrNi84Cu, - A first (metallurgical) level in which the bonding energy of an
resulting in a slowing down of dissolution and a completely different alloying element directly controls the dissolution probability of its
surface morphology. surrounding atoms. Strong chemical bonding will tend to block
the surface from dissolution (Mo, W etc.), whereas weak bonding
will enhance the dissolution rates by activating highly coordinated
Conclusions sites, increasing thereby the density of the initiation sites. This
effect is embodied in the pre-exponential term of the phenomeno-
In this work, we carried out MC simulations of the acidic dissolu- logical law of dissolution.
tion of various stainless steels grades with the aim to investigate the - A second (electrochemical) level related to the thermodynamic
effect of their chemical composition and/or crystallographic structure equilibria of a given chemical element in aqueous media. The
on the dissolution kinetics. Using ab initio calculations, we first eval- higher the standard potential of an alloying element, the lower
uated the bonding energies induced by alloying elements for different its dissolution probability, and this is likewise reflected in the
solid solutions (ferritic and austenitic). It was found that all the va- exponential term of the dissolution law.
lence orbitals (s, p and d) of a given alloying element contribute to
the chemical bonding, though there is a predominance for d-orbitals
depending on their occupancy state. 3d transition metals are found to
generate bonding energies comparable to Fe-Fe ones (in the case of From this perspective, the dissolution mechanisms of both ferritic
Cr, Ni, Ti and V), or even smaller (in the case of Cu and Zn) due to the and austenitic SS can be regarded as governed by the combination of
fully saturated 3d-orbitals. Note that Mn represents a singularity in these two aspects and a wide variety of situations was found:
this series since it tends to form weak bonds with all the other elements
due to the half-filled state of its d-orbitals. By contrast, 4d transition
metals systematically generate strong bonding energies (in the case - High bonding energies with high standard potentials (Mo): this
of Mo, Nb, Zr and W), except when one approaches orbital saturation configuration offers the highest dissolution resistance. One would
(in the case of Sn, Cd, In etc.). We believe that this wide variety of expect similar behavior from W.
bonding energies in SS has a substantial impact on the dissolution - High bonding energies but low standard potentials (Nb): a drop in
mechanisms of both ferritic and austenitic SS. the dissolution resistance is obtained.
Through a series of simulations conducted on several SS grades, - Low bonding energies with high standard potentials (Cu): this is
we found that the role of the alloying elements should be considered reflected in a selective dissolution of the SS due to the blocking
at two different levels: effect of Cu atoms on the surface.
Downloaded on 2018-08-16 to IP 88.162.207.150 address. Redistribution subject to ECS terms of use (see ecsdl.org/site/terms_use) unless CC License in place (see abstract).
Journal of The Electrochemical Society, 165 (10) C703-C709 (2018) C709
These findings remain the same in the case of austenitic SS, though 15. R. Callejas-Tovar, C. A. Diaz, J. M. Martinez de la Hoz, and P. B. Balbuena, Elec-
with, higher degrees of complexity, with the crystallographic structure trochimica Acta., 101, 326 (2013).
16. J. Erlebacher, J. Electrochem. Soc., 151, C614 (2004).
itself exhibiting little influence on the dissolution ability. 17. I. McCue, E. Benn, B. Gaskey, and J. Erlebacher, Annu. Rev. Mater. Res. 46, 263
(2016).
18. B. Diawara, Y.-A. Beh, and P. Marcus, J. Phys. Chem., 114, 19299 (2010).
ORCID 19. J. Greeley and J. K. Nørskov, Electrochimica. Acta., 52, 5829 (2007).
20. Q. Du, V. Faber, and M. Gunzburger, SIAM Rev. 41, 637 (1999).
B. Malki https://orcid.org/0000-0002-2605-1565 21. R. G. Parr and W. Yang, “Density Functional Theory of Atoms and Molecules,”,
Oxford University Press, New York, (1989).
22. J. P. Perdew, K. Burke, and M. Ernzerhof, Phys. Rev. Lett. 77, 3865 (1996).
References 23. S. Kurth, J. P. Perdew, and P. Blaha, Int. J. Quant. Chem., 75, 889 (1999).
24. X. Gonze, B. Amadon, P. M. Anglade, J. M. Beuken, F. Bottin, P. Boulanger,
1. B. Malki, S. Saedlou, I. Guillotte, and B. Baroux, J. Electrochem. Soc., 163, C807 F. Bruneval, D. Caliste, R. Caracas, T. Deutsch, L. Genovese, P. Ghosez,
(2016). M. Giantomassi, S. Goedecker, D. Hamann, P. Hermet, F. Jollet, G. Jomard, and
2. R. S. Lillard, G. F. Wang, and M. I. Baskes, J. Electrochem. Soc.,153, B358 S. Leroux, Comput. Phys. Commun., 180, 2582 (2009).
(2006). 25. X. Gonze, J. Beuken, R. Caracas, F. Detraux, M. Fuchs, G. Rignanese, L. Sindic,
3. E. Kim, P. F. Weck, C. D. Taylor, O. Olatunji-Ojo, X. Liu, E. Mausolf, G. D. Jarvinen, M. Verstraete, G. Zerah, F. Jollet, M. Torrent, A. Roy, M. Mikami, P. Ghosez, J. Raty,
and K. R. Czerwinskie, J. Electrochem. Soc., 161, C83 (2014). and D. Allan, Comput. Mater. Sci., 25, 478 (2002).
4. C. D. Taylor, Journal of Metallurgy, 2011, 954170 (2011). 26. X. Gonze, G. Rignanese, M. Verstraete, J. Beuken, Y. Pouillon, R. Caracas,
5. C. D. Taylor, J. Nuc. Mat., 408, 183 (2011). F. Jollet, M. Torrent, G. Zerah, M. Mikami, P. Ghosez, M. Veithen, J. Raty,
6. C. D. Neurock and X. Y. Liu, J. Nuc. Mat., 434, 382 (2013). V. Olevano, F. Bruneval, L. Reining, R. Godby, G. Onida, D. Hamann, D. Allan,
7. C. D. Taylor, R. G. Kelly, and M. Neurock, Journal of The Electrochemical Society, and Z. Kristallogr., Z. Kristallogr., 220, 558 (2005).
154, 217 (2007). 27. M. Torrent, F. Jollet, F. Bottin, G. Zrah, and X. Gonze, Comput. Mater. Sci., 42, 337
8. C. D. Taylor and M. Neurock, Current Opinion in Solid State and Materials Science, (2008).
9, 49 (2005). 28. “ABINIT PAW Atomic Data” (2014).
9. C. D. Taylor, S. A. Wasileski, J. S. Filhol, and M. Neurock, Physical Review B, 73, 29. H. J. Monkhorst and J. D. Pack, Phys. Rev. B, 13, 5188 (1976).
165402 (2006). 30. M. Torrenta, F. Jolleta, F. Bottina, G. Zéraha, and X. Gonze, Comput. Mater. Sci., 42,
10. G. S. Frankel, J. Electrochem. Soc., 145, 2186 (1998). 337 (2008).
11. Shubhabrata Datta and J. Paulo Davim, “Computational Approaches to Mate- 31. F. D. Murnaghan, Proc. Nat. Acad. Sci., U.S.A. 30, 244 (1944).
rials Design: Theoretical and Practical Aspects,”, IGI Global Editor; 1st Ed, 32. P. Marcus, Corrosion Science., 36, 2155 (1994).
(2016). 33. "CRC Handbook of Chemistry and Physics,", CRC Press, New York, (1996).
12. H. Eyring, Journal of Chemical Physics., 3, 107 (1935). 34. T. Sourisseau, E. Chauveau, and B. Baroux, Corrosion Science, 47, 1097 (2004).
13. K. J. Laidler, Theories of Chemical Reaction Rates, in “McGraw-Hill Series in Ad- 35. K. Fushimi, Y. Takabatake, T. Nakanishi, and Y. Hasegawa, Electrochimica Acta.,
vanced Chemistry”, p 234 (1969). 113, 741 (2013).
14. Davis and E Neal, PhD thesis, University of Illinois (2011). 36. R. K. Guptaa and N. Birbilis, Corrosion Science., 92, 1 (2015).
Downloaded on 2018-08-16 to IP 88.162.207.150 address. Redistribution subject to ECS terms of use (see ecsdl.org/site/terms_use) unless CC License in place (see abstract).